8

Products and Services and Services Access Scaffolding Systems!TSS Total Scaffold System (Steel/Aluminum)!TSF Total System Frame (Aluminum)!Traditional Frame Scaffolding Shoring Systems!Truss

Embed Size (px)

Citation preview

Products and Services

Access Scaffolding Systems

! TSS Total Scaffold System (Steel/Aluminum)

! TSF Total System Frame (Aluminum)

! Traditional Frame Scaffolding

Shoring Systems

! Truss Shoring System (Steel/Aluminum)

! QSS Quick Strip System (Aluminum)

! HD Frame Shoring (Steel/Aluminum)

! Post Shores (Steel/Aluminum)

Forming System

! Panel Forming System (Steel/Aluminum)

! Mega Form Panel Forming System (Aluminum)

! Gang Forming System (Aluminum)

! Aluminum Beams

! Aluminum Strong Backs

Technical Services

! Project Analysis

! Technical Training

! On Site Technical Support

! Custom Design

TOTAL SCAFFOLD SYSTEM

Etobicoke Ironworks Limited141 Rivalda Road Weston Ontario M9M 2M7

Tel: (416) 742-7111email: [email protected]

Fax: (416) 742-2737www.eiw-ca.com

W

wW

wW Etobicoke Ironworks Limited

141 Rivalda Road Weston Ontario M9M 2M7Tel: (416) 742-7111email: [email protected]

Fax: (416) 742-2737www.eiw-ca.com

Distributed by:

CODE LENGTH WEIGHT

156840 4' (1.219 m) 21 lbs (9.6 kg)

156850 5' (1.524 m) 25 lbs (11.4 kg)

156860 6' (1.829 m) 31 lbs (14.0 kg)

156870 7' (2.130 m) 36 lbs (16.4 kg)

156880 8' (2.438 m) 41 lbs (18.7 kg)

156900 10' (3.048 m) 50 lbs (22.7 kg)

CODE LENGTH WEIGHT

157840 4' (1.219 m) 26 lbs (11.8 kg)

157850 5' (1.524 m) 31 lbs (14.1 kg)

157860 6' (1.829 m) 38 lbs (17.3 kg)

157870 7' (2.130 m) 45 lbs (20.5 kg)

157880 8' (2.438 m) 51 lbs (23.2 kg)

157900 10' (3.048 m) 62 lbs (28.2 kg)

SAFE WORKING LOAD22.30 kN/m

2(50 lbs/ft )

SAFE WORKING LOAD22.30 kN/m

2(50 lbs/ft )

SAFETY-GRIP PLANK (10” WIDE)

SAFETY-GRIP PLANK (12” WIDE)

*OTHER PLANKS/DECKS AVAILABLE UPON REQUEST

wW

Fit adjustable bases with collars and layout roughly in position with theircorresponding ledgers. Pick the highestground level for a setting out point tosimplify later adjustment. It helps if thescrew jack is near (not at) the bottom ofthe thread by allowing maximumadjustment on lower ground levels.

Connect the ledgers to the rosette on thecollar of the adjustable base. DO NOTDRIVE HOME THE WEDGES AT THISSTAGE.

Using a spirit level, adjust the bases sothat the ledgers are horizontal. Accuracyin leveling at this stage eliminates theneed for further leveling and plumbing asthe scaffolding is erected.

Place two aluminum planks or four 255mm(10”) wide board in each bay spanningthe ledgers to square up the system.Move progressively round the base of thescaffolding. When squared and leveleddrive home the wedges.

When basing out is completed, the firststandards are positioned into the collarof the base.

Ledgers can now be placed at the requiredlevels.

Handrails is automatically positioned.

Planks are now moved up to this first lift,decking out fully if this is to be a workingplatform.

Fix diagonal braces across the face of thebays. Hammer wedges home.

The scaffolding is completed by addingledger midrails, handrails and toe boardson the working platform.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

TOTAL SCAFFOLD SYSTEMERECTION PROCEDURE

wW

DESCRIPTION CODE LENGTH WEIGHT

SL 10 152100 3.05 m (10'0") 11.6 kg (25.4 lbs)

SL 8 152800 2.44 m (8'0") 9.2 kg (20.3 lbs)

SL 7 152700 2.13 m (7'0") 8.3 kg (18.3 lbs)

SL 6 152600 1.83 m (6'0") 6.9 kg (15.2 lbs)

SL 5 152500 1.57 m (5'2") 6.5 kg (14.2 lbs)

SL 4 152400 1.15 m (3'10") 4.8 kg (10.6 lbs)

SL 2 152200 0.65 m (2'2") 3.1 kg (6.8 lbs)

CUSTOM SIZES AVAILABLE UPON REQUEST

DESCRIPTION CODE HEIGHT WEIGHT

1.0m Standard 151100 1.00 m (3'3") 5.0 kg (11lbs)

1.5m Standard 151150 1.50 m (4'11") 7.5 kg (16 lbs)

2.0m Standard 151200 2.00 m (6'7") 9.5 kg (21 lbs)

3.0m Standard 151300 3.00 m (9'10") 14.3 kg (31.5 lbs)

Total Scaffold System (TSS) is manufactured usinghi-strength steel, robotically welded and hot-dipgalvanize finish. This offers the user the highestpossible product quality and durability with the leastpossible maintenance.

Typical project applications include:suspended scaffolding, scaffold fortanks, petro-refineries and otherindustrial uses, access scaffold formasons, precasters, bricklayers, temporary grandstands or stages for cultural events.

The EIW Total Scaffold System isone of the most advanced,sophist icated and completemodular system on the worldmarket. All components are engineered to lock onto the uniquerosette, and the system isd e s i g n e d t o m i n i m i z enumber of pieces and keep allcomponents standard and flexible.The Total System is erected withspeed and efficiency resulting incost savings through labour andscheduling. The fastest and mostefficient way of erecting scaffoldingto suit all types of structures,refineries, industrial buildings,renovations, special events andmany other structures and towers.

VERSATILE

TSS STANDARDS

SINGLE LEDGERS

(AVAILABLE IN ALUMINUM)

(AVAILABLE IN ALUMINUM)

CODE LENGTH WEIGHT

179565 3' 10" (1.168 m) 20 lbs (9.5 kg)

179560 5' 2" (1575 m) 27 lbs (12.3 kg)

179555 6' (1.829 m) 31 lbs (14.1 kg)

179550 7' (2.130 m) 36 lbs (16.4 kg)

CODE LENGTH WEIGHT

179590 6' (1.829 m) 20 lbs (9.5 kg)

179585 7' (2.130 m) 23 lbs (10.5 kg)

179580 8' 6" (2.590 m) 27 lbs (12.5 kg)

179570 10' (3.048 m) 32 lbs (14.5 kg)

EIW TOTAL PLANK

SAFE WORKING LOAD23.60 kN/m

2(75 lbs/ft )

SAFE WORKING LOAD23.60 kN/m

2(75 lbs/ft )

SAFE WORKING LOAD23.60 kN/m

2(75 lbs/ft )

ALUMINUM PLANK (9.5” WIDE)

ALUMINUM PLANK (12” WIDE)

ALUMINUM PLANK (19” WIDE)

CODE LENGTH WEIGHT

179620 3' 10" (1.168 m) 11 lbs (5.0 kg)

179615 5' 2" (1.575 m) 13 lbs (5.9 kg)

179610 6' (1.829 m) 15 lbs (6.9 kg)

179605 7' (2.130 m) 18 lbs (8.1 kg)

179600 8' (2.438 m) 20 lbs (9.5 kg)

TSS STAIRWAYS

TSS FRAMES

STAIR THREADCODE:

WEIGHT:

160620 (41” WIDE)160630 (32” WIDE)

10 - 12 lbs STAIR STRINGERCODE:

WEIGHT:

160600 (8’ 6”)160610 (7’)

45 - 55 lbs

WEIGHT: 54 lbs (24.5 kg)CODE: 101145

WEIGHT: 46 lbs (20.9 kg)CODE: 101100

3’ 10” x 6’ 6” SYSTEM ARCH FRAME 2’ 4” x 6’ 6” SYSTEM ARCH FRAME

DESCRIPTION CODE LENGTH WEIGHT

DTL 28 154280 8.52 m (28' 0") 100 kg (219 lbs)

DTL 21 154210 6.39 m (21' 0") 73 kg (160 lbs)

DTL 20 154200 6.10 m (20' 0") 68 kg (150 lbs)

DTL 17 154170 5.18 m (17' 0") 59 kg (130 lbs)

DTL 14 154140 4.26 m (14' 0") 47 kg (103 lbs)

Speed of erection and dismantlingare possible because of themodularity of the system and anabsence of loose fittings, such asnuts, bolts or clamps. All pieces arepre-measured and pre-engineered. All of which cuts the labour costs considerably.

There exists minimal chance of error due to the “positive” lockjoints, pre-set modules, the lightweight factor of the componentsand the simple fact that one personwith one hammer can erect thesystem.

ECONOMICAL

SAFE

DOUBLE LEDGERS

DOUBLE TRUSS LEDGERS

(AVAILABLE IN ALUMINUM)

(AVAILABLE IN ALUMINUM)

CUSTOM SIZES AVAILABLE UPON REQUEST

DESCRIPTION CODE LENGTH WEIGHT

TL 10 153100 3.05 m (10' 0") 22.4 kg (49 lbs)

TL 8 153800 2.44 m (8' 0") 17.9 kg (39 lbs)

TL 7 153700 2.13 m (7' 0") 15.8 kg (35 lbs)

TL 6 153600 1.83 m (6' 0") 13.3 kg (29 lbs)

TL 5 153500 1.57 m (5' 2") 11.8 kg (26 lbs)

wW

COMBINATION SIDE BRACKET& WALL TIE

DESCRIPTION CODE LENGTH WEIGHT

SB 880 156588 0.88 m (2' 11") 10.0 kg (22.0 lbs)

SB 650 156565 0.66 m (2' 2") 7.0 kg (15.3 lbs)

SB 400 156563 0.40 m (1' 4") 4.0 kg (9.0 lbs)

CANTILEVER APPLICATION

DESCRIPTION CODE LENGTH WEIGHT

BB 10 155100 3.56 m (11' 8-1/4") 11.8 kg (26.0 lbs)

BB 7 155700 2.85 m (9' 4-1/8") 9.5 kg (21.0 lbs)

BB 5 155500 2.48 m (8' 1-11/16") 9.1 kg (20.0 lbs)

BB 4 155400 2.26 m (7' 4-7/8") 7.5 kg (16.5 lbs)

BB 2 155200 2.07 m (6' 9-5/8") 6.9 kg (15.2 lbs) This is the best word to describe theTotal Scaffold System. In terms ofadaptability, the system can besuited to any project requirementand conditions. The rosette cantake 8 connections on the sameplane.

ADAPTABLE

SPECIAL EVENTSDuring special events, the TotalScaffold System converts to grand-stands, bleachers, stages, VIP suitesor television towers. Modular indesign and portable, the productoffers safety, capacity and versatility.The System for special events wasdesigned with safety and efficiencyin mind, capable of withstandingdynamic loads comparable to per-manent structures and to rival theirdu rab i l i t y . Grands tands andbleachers can be put together byunskilled workers quickly and easilybecause of the pre-set designs andlack of nuts, bolts and clamps whichdominate other systems.

BAY BRACES(AVAILABLE IN ALUMINUM)

SIDE BRACKET(AVAILABLE IN ALUMINUM)

CUTOM SIZES AVAILABLE UPON REQUEST

LARGER BRACKETS CAN BE MADE USING STANDARDCOMPONENTS OF LEDGERS, BASE COLLARS AND BAY BRACES

BAY BRACES ARE DESCRIBED BY THE HORIZONTAL RUNOR THE SAME AS THE LEDGER THEY WORK WITH.THE RISE ON ALL STANDARD BAY BRACES IS 2.0 m (6’ 6”)

CUSTOM SIZES AVAILABLE UPON REQUEST

W

STAIRWAY (7’ BAY)10 LEGS STANDARD DESIGN MEETSNATIONAL BUILDING CODE

PETRO-CHEMICAL, PULP &PAPER, OFFSHORE,POWER PLANTS

NEW CONSTRUCTION

F o r i n t r i c a t e , c o m p l e x a n demergency access situations, theEIW Total Scaffold System is theonly choice. The easy to handlemodular components can beconnected around any structure,piping, walkways and adapted tomeet any project requirement. Thatis why refineries and industrial plantsrely on the EIW Total ScaffoldSystem. The versatility, the speed oferection and the safety are the keyingredients to a cost effectivesystem.

The EIW Total Scaffold System isadaptable to new constructionrequirements such as: outsidescaffolding to high rise buildings foruse by masonry contractors,precasters and outside claddingcontractors. It can be erected incomplex areas as atriums or specialhigh ceilings for glazers, painters andelectrical work.

BASE JACKCODE: 156010

SIZE: 6” x 6” x 24”ADJUSTMENT: 18”

WEIGHT: 15 lbs

ACCESSORIES

BASE PLATECODE: 108140SIZE: 6” x 6”WEIGHT: 3.5 lbs

SAFETY CLIPCODE: 163100WEIGHT: 0.25 lbs

BASE COLLARCODE: 156530WEIGHT: 4.0 lbs(AVAILABLE IN ALUMINUM)

ADAPTOR BOLT CLAMPCODE:

WEIGHT:

163130 (RA)

3.5 lbs163140 (SWIVEL)

THE EIW TECHNICALADVANTAGE

EIW uses 70 ksi (482 MPA) hightensile steel. The key componentsof the system are the Rosette,Ledger and Brace Heads all ofwhich are robotically welded withstate of ar t machinery. A l lcomponents are hot dippedgalvanized, meaning a much longermaintenance free lifespan of thep r o d u c t . C h e c k d a t a a n dengineering manual for furtherinformation. EIW can providetechnical drawings and advice oncomplex projects.

RENOVATION/REHABILITATION

There is no project that is impossibleto handle. The more unusual andirregular the shape or anglestructure, the better. ChurchSteeples, Building Towers, CityHalls, Clock Towers and complexgeometrical facades are easilyhandled by EIW Total Scaffold System. Even the most difficult problem such as entrances,recessed facades, height ofplatforms and special loadingrestrictions are overcome in themost economical way possible.

STARTER BRACKETCODE: 115100

WEIGHT: 6.0 lbs

RIGHT ANGLEBOLT CLAMPCODE: 163215WEIGHT: 4.0 lbs

SWIVEL BOLT CLAMPCODE: 163220WEIGHT: 4.0 lbs

SPIGOT ADAPTORCODE: 164000WEIGHT: 4.0 lbs

LADDERCODE: 115103 (3’)

115105 (5’)SIZE: 3’ - 8’WEIGHT: 17 - 33 lbs

(AVAILABLE IN ALUMINUM)

CODE: 161010SIZE: 8”WEIGHT: 12.0 lbs

CAPACITYStation: 500 kg or 1100 lbsRolling: 250 kg or 550 lbs

CAPACITYStation: 1000 kg or 2200 lbsRolling: 500 kg or 1100 lbs

CODE: 161011SIZE: 8”WEIGHT: 13.0 lbs

CASTER WHEELS