Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
● Adopts MCU Processing
● Manual Test / Auto-Reset
● Hush Function
● Low Voltage Compensation
● Temperature Compensation
● Low Battery Warning
● Auto-Check Malfunction in Smoke Chamber
● Anti-RF Interference (20V/m-1GHz)
● Dustproof, Mothproof, Anti-light Interference
● SMT Manufacture Technology with High Reliability
● Shockproof Design Suitable for Vehicle Use
INSTALLATION
1. Avoid installations in places with stagnating smoke, heavy
dust, heavy water mist, heavy oil mist, great humidity
(>95%) and high wind speed (>5m/s).
2. Insert the ready battery into the .
Choose a proper position. Normally, the center of the
detection area ceiling is recommended. Fix the detector base
into the chosen position. Then put the detector into the base
and twist to fasten it. Be sure it is fastened tightly.
battery compartment
User Manual of Photoelectric Smoke Detector
1
PRODUCT INTRODUCTION
PRODUCT PROFILE
FEATURES
This product is a battery operated photoelectric smoke
detector. The smoke chamber using the principle of smoke
particles reflecting infrared lights can accurately detect the
early smoke of a fire. When concentration of the leaked
smoke density reaches the given alarm level, the detector LED
flashes red and buzzer gives out alarm sounds. Besides
suitable for early warning and protection of fires in houses,
villas, factories, shopping malls, warehouses, office buildings
etc. indoor places, this unit has a subtle shockproof design,
which makes it also suitable for vehicle use.
OPERATING PRINCIPLE
1. Insert the 2pcs 1.5V AA batteries into the battery
compartment. The detector enters into normal working
status. The LED flashes green once every 30s, indicating
normal power supply.
2. The detector should be tested periodically during use. Short
press Test & Hush Button to run a test. The LED flashes Red
along with buzzer sounding for alarm indication. Do not test
the detector too often to save battery life. One a month is
recommended.
3. During alarming status, short press the Test & Hush Button.
Then the detector goes into mute status. The LED keeps
flashing red while the buzzer will stop sounding. If the alarm
status hasn’t been reset , the mute status wil l end
automatically in 10 minutes later. The buzzer sounds again.
If the alarm status is reset during the 10 minutes, the detector
recovers to normal working status.
4. The detector can auto check open circuit, short circuit and
other malfunctions in smoke chamber. During malfunction,
1
Test & Hush Button
LED Indicator
Battery Compartment
TECHNICAL PARAMETER
Operating Voltage DC 3V (2pcs AA alkaline batteries)
Static Current ≤15uA
Alarm Current ≤35mA
Hush Time 10 minutes
Smoke Sensitivity
Alarm Indication
Failure Indication
Sound Level
Temperature Range
Humidity
Installation Mode
Dimension
Execute Criterion
0.2dB/m(±0.05dB/m)
Red LED and buzzer sounds
Yellow LED
≥85dB/3m
≤95RH (No Congelation)
-10°C ~ +50°C
Wall or Ceiling mounted
Φ110*45mm
EN14604-2005,GB15322.5-2003
M201-3EVer1.0
1
1. Replace the batteries with new ones in time on low battery
condition to ensure normal operation.
2. No block within a radius of 0.5m from the detector.
3.The horizontal distance from the detector to the air
conditioner outlet should not be less than 1.5m.
4. If needs to install the detector in an aisle ceiling with a width
less than 3m, choose a center position. Keep the distance
between the detectors less than 15m. The distance from the
detector to the end wall should not exceed half of the
distance between the detectors.
5. Clean the detector surface with soft brush every month to
EMERGENCY ALARM TREATMENTS
NOTES
Treatments when a smoke alarm is reported:
1. Inspect the causes. If it is caused by cigarette smoking or
other reasons and not a fire alarm, just remove the smoke
resource and the alarm will reset. If it is a false alarm, check
if the installing position is improper.
2. If a fire breaks out, in the early stage, use a fire extinguisher
to put out the fire.
3. If the fire is large, don’t panic. Escape asap and then call the
police.
User Manual of Photoelectric Smoke Detector
2
INDICATIONS SUMMARY
Indications Analysis Elimination
+LED flashes Greenonce every 30s
Normal, indicating normalbattery supply
LED flashes Red
Normal. Caused by pressing Test & Hush Button under alarm or testing status. Detector enters into Mute status.
Repress the Test & Hush Button to lift the mute status
LED flashes Yellow once every 30s along with buzzer sounding
Low battery (<2.4V) Replace newbatteries
LED flashes Yellow twice every minute along with buzzer sounding
Malfunction in smoke chamber
Contact your dealer for repairing or replacement
the LED flashes yellow, twice a minute along with buzzer
sounding to warn user.
5. When battery voltage < 2.4V, the detector will give out low
battery signal periodically. The LED flashes yellow, once
every 30s along with buzzer sounding.
ensure sensitivity. Do not spray air-freshers, hair gels,
paints or other aerosols near the detector.
6. For malfunction problems, contact your dealer. Do not
dismantle and try to repair it privately.
7. The detector can reduce accidents happening, but can not
g u a r a n t e e a h u n d r e d p e r c e n t s a f e t y. F o r s a f e t y
consideration, besides proper usage of the detector, pay
attention to build up safety consciousness and take
preventive measures in daily life.
8. Maintain the detector periodically as per requirements in this
manual.
M201-3EVer1.0