Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
1
LT-904
8 bit / 16 bit
CHANNELS
2 kinds of DMX interfaces
www.ltech-led.com
6. With fast self-testing function.
8. 16bit (65536 levels) / 8bit (256 levels) grey level optional.
7. High/low frequency PWM for optional
2. Easy operation with digital display and the touch buttons.
1. Designed with 4 channels output, and Max. 6A current per channel, up to 576W output power.
Product introduction
www.ltech-led.com
4. With RDM remote management protocol, the operations can be completed via the RDM master console, such as parameters browsing & setting, DMX address setting, equipment recognition, etc.
006
OTP/OCP/SCP protection
Photoelectricisolation
3. 3-pin XLR, RJ45 DMX interface with photoelectric isolation, improve signal transmission efficiency and anti-interference ability.
1
warranty5 years
E500585
Short circuitProtection
RDM Over currentProtection
RJ453-pin XLR Photoelectricisolation
Over temp.protection
5. when fault.
With short circuit / over temp. / over current protection, as well as warning function
Technical specs
www.ltech-led.com
Unit: mm
LT-904
DMX512/RDM
3-pin XLR, RJ45
~
×
× 4CH Max. 576W
12 24Vdc
6A 4CH Max. 24A
(0~72W...144W)
8bit (256 levels) / 16bit (65536 levels)
Protection:
Working temp.:
:
:
:
Dimensions
Package size
Weight (G.W.)
Model
Input signal
Input voltage
Current load
:
:
DMX interface:
:
:
:
Output power:
Grey level
Short circuit / Over temp./ Over current protection,
recover automatically.
-30°C~65°C
L122×W110×H37mm
L127×W123×H41mm
550g
Photoelectric isolation: Yes
11086
110
2
37
122
Main component description
Signal indicator
Digital display
Screen
Hig Smooth
Low Std
30S off
Enable
PWM Hz DIM
Digital display will enter the locked mode without operating after 15 seconds.
Dip switch
16
Bit
8
Long press “M” key to unlock.
Short press “M” key to switch numbers.
Press “ ””v” key to adjust value.^
M <<
888
www.ltech-led.com
Power indicator 12-24Vdc
input voltageLED lamps connection
Digital display
Dip switch
RJ453-pin XLR
DMX/RDM input & output
DMX/RDM input & output
006
3
4 5
www.ltech-led.comwww.ltech-led.com
DMXRDM
DMXRDM
Wiring diagram
1 Connecting LED lights:
Signal Signal
LEDPower Supply
12-24Vdc
DMX
console
2. DMX console onnectionc :
DMX signal DMX signal
12-24Vdc 12-24Vdc 12-24Vdc
Resistor terminal
An amplifier is needed if more than 32 decoders are connected , signal amplification should not be more than 5 times continuously.
or use overlong signal line
If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W 90-120Ω terminal resistor at the end of each line.
LT-904 is equipped with 2 types DMX terminals for users’ selection. The following diagram takes 3-pin XLR as an example, same connecting method for RJ45.
*
*
RGBW LED
RGBW LED
DMX signalLT-904
LT-904 LT-904 LT-904
132
PUSH
132
PUSH
GND
DATA+DATA-
V+
1
2
3
4
www.ltech-led.com
These 2 terminals can be connected in a mixed way.
Rj45 connected in parallel
3-pin XLR connected in parallel
3. The connection diagram of 2 kinds of DMX/RDM terminals:
* Installation attention : please reserve enough ventilation distance between decoders (>20mm),
be sure not to block the vent, or will affect lifetime of decoder for .poor heat dissipation
Installation distance > 20mm
Vent
LT-904 LT-904
LT-904 LT-904
6
Terminal resistor
Terminal resistor
LT-904
LT-904
Update time: 2019.07.20_A1
No further notice if any changes in the manual.Product function depends on the goods. Please feel free to contact your supplier if any question.