Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
PRODUCT INFORMATION
Penco Clipper Shelving
2946 Larimer St. Denver, CO 80205 303-295-1100 / 800-373-7693 FAX 303-295-2464 Email [email protected] www.snyderequipment.com
1
Clipper ® Industrial Shelving
Clipper® ShelvingFeatures Hi-Performance®
Box Beam Shelves
Automatic shelf welding on Hi-Performance shelfproduction line.
Cross Section of a Hi-Performance shelf.
Four Clipper Compression Clipsincluded with each shelf. Shelf is held
tight against post.
Clipper Clipallows shelfadjustment on 1"vertical centers.
Penco Clipper Hi-Performance shelves areproduced on a state-of-the-art productionline that begins with a flat steel blank andends with a completed shelf. The result is ashelf with an exceptional strength to weightratio.
A. Front and rear flanges of each shelfutilize Box Beam construction for extrastrength – no additionalreinforcing necessary.
B. Sides are double flangedand accept additionalreinforcements ifrequired.
C. Flanges are welded to theunderside of shelf on 3"centers.
D. Corners are lapped andwelded.
E. Shelves are available in three maincapacity ranges: Medium, Heavy Dutyand Extra Heavy Duty.
At the heart of the Clipper Shelving Systemis the ingenious Penco Clipper Clip. It iseasily installed, holds the shelf firmly inplace, can be repositioned at any time, andactually helps make the shelving more rigid.Clipper Shelving offers a wide variety ofsizes and capacities. This gives you theflexibility to provide top quality storage fora simple back room area, or a sophisticatedmulti-level or high-rise application.The following pages detail the units, compo-nents and accessories for designing ashelving system that meets your individualneeds. You can’t buy finer industrial gradeshelving than Penco Clipper.
B
EC
AA
D
C
D
®
2
Clipper ® Shelving VersatilityVersatile Clipper Shelving can be accessorized for any job.
Clipper Hi-Performance® ShelfAvailable in 19 sizes and 4classes of load carrying capacity.May be clipped or bolted to posts.
Base StripDesigned to closethe space betweenthe bottom shelfand floor topromote goodhousekeeping.
Side PanelSteel sheet usedto encloseshelving sides oras a partitionbetween sectionsplaced side byside.
Back PanelCompletely closesthe back ofshelving units andprovides lateralstability.
Full HeightDividersUsed to subdividethe shelf openinginto smaller units.Punched top andbottom for attach-ment to shelves.
Heavy DutyModular DrawersProvides securehigh densitystorage for smallparts. 100% fullextension.
Shelf BoxesStrong steel opentopped box forstoring small parts.Equipped withbuilt-in stop.
Partial DividerDivides shelfsurface intosections.
Bin FrontTo retain smallbulk parts on shelf.
Finished EndPanelAn optionalattractive row endwithout exposedfasteners. (Notshown.)
Box PostUsed as a common front post orrow end. Allows independent 1"vertical adjustability and accessto the full shelf width.
OffsetAngle PostRoll formed forstrength andpunched on 1"centers for shelfadjustment. Canbe used at front orback of unit.
Sliding DividerFormed to fitaround front andrear flanges of theshelf. May bepositionedanywhere alongshelf surface.
Back BracesAttaches to rearposts of opentype shelving toensure lateralstability.
Side BracesEliminates front toback sway onopen typeshelving.
®
Label HolderAccepts 7/8" labels.
3
Basic Clipper Ordering Data
Clipper Open & Closed Shelving in a retail storage lock-up area.
How To Order Clipper Units
Virtually all shelving storage needs may besatisfied by ordering standard shelving units asillustrated on the following pages.
These units are shipped KD with all requiredcomponents, shelf clips, hardware and assemblyinstructions.
To order standard shelving units 87" high:
1. Determine the shelving type desired(open, closed or ledge).
2. Determine shelf width and depth.3. Order by catalog number as many
basic units as required to form acontinuous row of shelving.
4. Order by catalog number oneending kit to end each row.
5. Select the appropriate accessoriesfor your application.
Growth Dimension ConsiderationsSeveral factors contribute to dimensional growth of acontinuous row of shelving beyond specified dimensions.To determine the overall dimension of a continuous row ofshelving employing box posts, refer to detail drawings andtable below.
Choice of Post ArrangementsPenco standard shelving units employ box posts at frontand offset angle posts at rear for each section. Other postassembly plans may be employed using offset angle postsat front and rear, when ordered as individual componentparts. The illustrations below show typical growth for 36"wide units using two types of post arrangements.
Growth Showing Clipper Conventional Flange Shelves
3' - 0 5/8" 3' - 0 5/8" 3/8"9' - 2 5/8"
Box Posts Front, Angle Posts Rear
3' - 0 5/8"3/8"
STARTER ADD-ON ADD-ONDepth
+5/16"
3' - 0 5/8" 3' - 0 5/8" 3' - 0 5/8"9' -1 7/8"
Angle Posts Front & Rear
STARTER ADD-ON ADD-ONDepth
+5/16"
Growth ShowingPenco High Performance® Shelves
3' - 0 1/2" 3' - 0 1/2" 3/8"9' 2-1/4"
3' - 0 1/2" 3' - 0 1/2" 3' - 0 1/2"9' 1-1/2"
Box Posts Front, Angle Posts Rear
Angle Posts Front & Rear
3' - 0 1/2"3/8"
STARTER ADD-ON ADD-ON
STARTER ADD-ON ADD-ONDepth
+5/16"
Depth+
5/16"
All dimensions are theoretical subject tomanufacturing tolerances.
4
Open Clipper UnitsOpen type shelving is the basic and most economicalshelving design for general purpose use. Backs and sidesare open, except that sections are stabilized by swaybraces.
For convenient ordering, 36 different open configurations ofBasic Units are shown below with their respective End Kits.The completed units below utilize Heavy Duty Hi-Performance®
Shelves with box posts at front and offset angle posts atrear. Label holders are not included. Refer to page 3 forordering instructions.
The standard stock color for Clipper shelving is 028 Gray.Refer to the inside back cover for complete color informa-tion. Many other configurations can be designed from thecomponent parts and accessories on the following pages.
End Kit1 box post1 set side
swaybraceshardware
Basic Unit1 box post2 angle posts1 set side sway braces1 set back sway braces
shelveshardware
OPEN TYPE SHELVINGBox Post at FrontOffset Angle Posts at Rear
** For Evenly Distributed Load
snoisnemiD)sehcni(
**yticapaCflehSreP flehS5 flehS6 flehS7 flehS8 tiKdnE
W D H sdnuoP tinUcisaB.oN.taC
tinUcisaB.oN.taC
tinUcisaB.oN.taC
tinUcisaB.oN.taC
tiKdnE.oN.taC
636363
218142
787878
008058008
5107H15207H15307H1
6107H16207H16307H1
7107H17207H17307H1
8107H18207H18307H1
782101788101784201
242424
218142
787878
006006006
5407H15507H15607H1
6407H16507H16607H1
7407H17507H17607H1
8407H18507H18607H1
782101788101784201
848484
218142
787878
005005035
5707H15807H15907H1
6707H16807H16907H1
7707H17807H17907H1
8707H18807H18907H1
782101788101784201
5
Closed Clipper UnitsLabel holders and closed front bases are not included andmust be ordered separately. Refer to page 3 for orderinginstructions.
Standard stock color is 028 Gray; refer to the inside backcover for complete color information. Many other configura-tions can be designed from the component parts andaccessories on the following pages.
Closed type shelving units are covered on three sides withsteel panels to provide stability, protection and to promotecleanliness of stored items. Optional locking doors may beadded for greater security.
The 36 configurations shown below with their respectiveEnd Kits employ Heavy Duty Hi-Performance® shelves withbox posts at the front and offset angle posts at the rear.
End Kit1 box post1 side panel
hardware
Basic Unit1 box post2 angle posts1 side panel1 back panel
shelveshardware
CLOSED TYPE SHELVINGBox Post at FrontOffset Angle Posts at Rear
Order Closed Bases Separately
flehS5 flehS6 flehS7 flehS8 tiKdnE **yticapaCflehSreP
snoisnemiD)sehcni(
tinUcisaB.oN.taC
tinUcisaB.oN.taC
tinUcisaB.oN.taC
tinUcisaB.oN.taC
tiKdnE.oN.taC sdnuoP W D H
5108H15208H15308H1
6108H16208H16308H1
7108H17208H17308H1
8108H18208H18308H1
7821C17881C17842C1
008058008
636363
218142
787878
5408H15508H15608H1
6408H16508H16608H1
7408H17508H17608H1
8408H18508H18608H1
7821C17881C17842C1
006006006
242424
218142
787878
5708H15808H15908H1
6708H16808H16908H1
7708H17808H17908H1
8708H18808H18908H1
7821C17881C17842C1
005005035
848484
218142
787878
** For Evenly Distributed Load
6
Front bases are included. Label holders must be orderedseparately. This and the following page catalog 36" & 48"wide units, but many other configurations are possible byordering component parts. Most units are available forquick shipment in 028 Gray. See inside back cover forother colors.
Clipper Shelving Bin Units are closed units with Heavy DutyHi-Performance® shelves, in various quantities, plus dividersand bin fronts as required. Offset angle posts are used atthe rear of each unit, and box posts at the front. Order oneEnd Kit to finish a unit or row of units.
Note: Bin widths are nominal. They are measured from the hole centers on the shelves, notthe vertical bead of the dividers.
36" Wide Clipper Bin Units
"78hgiH
SGNINEPO9 SGNINEPO31 SGNINEPO12 SGNINEPO12 TIKDNE
"9x"638"21x"631
"6x"6321"21x"631 "21x"2112 "21x"2112
stnorFniB"37
htpeD .oN.taC .oN.taC .oN.taC .oN.taC .oN.taC
"21"81"42
9016H19026H19036H1
3116H13126H13136H1
1216H11226H11236H1
1266H11256H11246H1
7821C17881C17842C1
"78hgiH
SGNINEPO92 SGNINEPO53 SGNINEPO73 SGNINEPO34 TIKDNE
"9x"961"21x"94"21x"219
stnorFniB"38
"9x"923"21x"213
"6x"942"21x"94"21x"219
"6x"642"9x"219"9x"94"21x"216
htpeD .oN.taC .oN.taC .oN.taC .oN.taC .oN.taC
"21"81"42
9216H19226H19236H1
5316H15326H15336H1
7316H17326H17336H1
3416H13426H13436H1
7821C17881C17842C1
7
With Heavy Duty Hi-Performance Shelves
®
Note: Bin widths are nominal. They are measured from the hole centers on the shelves, notthe vertical bead of the dividers.
48" Wide Clipper Bin Units
"78hgiH
SGNINEPO9 SGNINEPO31 SGNINEPO82 SGNINEPO82 TIKDNE
"9x"848"21x"841
"6x"8421"21x"841 "21x"2182 "21x"2182
stnorFniB"37
.oN.taC .oN.taC .oN.taC .oN.taC .oN.taC htpeD
9046H19056H19066H1
3146H13156H13166H1
8246H18256H18266H1
8236H18226H18216H1
7821C17881C17842C1
"21"81"42
"78hgiH
SGNINEPO24 SGNINEPO25 SGNINEPO45 SGNINEPO85 TIKDNE
"9x"2/1-761"9x"98
"21x"2/1-74"21x"92"21x"2121stnorFniB"38
"9x"2/1-723"9x"961"21x"214
"6x"2/1-742"6x"921
"21x"2/1-74"21x"92"21x"2121
"6x"623"9x"2121"9x"2/1-74
"9x"92"21x"218
.oN.taC .oN.taC .oN.taC .oN.taC .oN.taC htpeD
2446H12456H12466H1
2546H12556H12566H1
4546H14556H14566H1
8546H18556H18566H1
7821C17881C17842C1
"21"81"42
8
Ledge & Counter UnitsLedge UnitsLedge type shelving is recommended where greater depthof the lower compartment is desired, and a convenientworking height surface ledge is required. Seven HeavyDuty Hi-Performance® shelves are included plus a heavygauge ledge top with a reinforcing pan welded to thebottom for extra strength. This provides a total of sevenopenings.
The units are available in open or closed construction andmay be equipped with standard shelving accessories,including locking doors at the top and the bottom. Unitsare 36" wide, 12" deep at the top, and 24" deep at thebottom. Overall height is 87"; the ledge top is 39" high.
The End Kit includes 2 ledge top finishing strips to providea finished appearance at the sides of the ledge top. Orderone End Kit to finish each single unit, or row of units.
Counter UnitsPenco steel counters present an extremely clean, classicappearance for over the counter or stockroom use. Asmooth, extra heavy gauge reinforced counter top providesan excellent work surface. Three standard Heavy Duty Hi-Performance® Clipper shelves, adjustable on 1" centers, areused below. Units have box posts at all four corners.
The top is designed to butt against adjacent tops whenmore than one unit is used in a row for a continuous flushsurface. One End Kit is required for each single unit, or toend a row of units. Two counter top finishing strips areincluded with each End Kit, to extend the top beyond theend and provide a finished appearance.
Front and rear views of2 1H122C Basic Unitsplus 1 19125E End Kit
Counter Units - 3 OpeningsSize Unit End Kit
W x D x H Cat. No. Cat. No.36" x 24" x 39" 1H122C 19125E42" x 24" x 39" 1H123C 19125E48" x 24" x 39" 1H124C 19125E
Counter Tops and Fronts may be purchased as separatecomponents. Note that they may be used only when boxposts are used at front and rear of unit.
Counter Tops OnlySize
W x D Cat. No.36" x 24" 13670H42" x 24" 13680H48" x 24" 13690H
Counter Fronts OnlySize
W x H Cat. No.36" x 39" 13870H42" x 39" 13880H48" x 39" 13890H
Open Type Ledge Unit
Size Unit End KitW x D x H Cat. No. Cat. No.
36" x 12/24" x 48/39" 1H432L 19433E
Closed Type Ledge Unit
36" x 12/24" x 48/39" 1H434L 19435E
Open Unitwith End Kit
Closed Unitwith End Kit
9
tinUcisaB tiKdnE
eziSHxDxW
fo.oNsevlehS
fo.oNsrediviD
golataCrebmuN
golataCrebmuN
"78"81"63 6 52 5076H1 7881C1
rediviDseititnauQ
H"61/31-41gninepOraelC-H06851.oN.taC-H"61xD"81-51H"61/31-61gninepOraelC-H07851.oN.taC-H"81xD"81-01
tinUcisaB tiKdnE
eziSHxDxW
fo.oNsevlehS
fo.oNsrediviD
golataCrebmuN
golataCrebmuN
"78"63"84 81 65 9566H1 7863C1
tinUcisaB tiKdnE
eziSHxDxW
fo.oNsevlehS
fo.oNsrediviD
golataCrebmuN
golataCrebmuN
"78"21"63 8 53 907671 7821C1
tinUcisaB tiKdnE
eziSHxDxW
fo.oNsevlehS
fo.oNsrediviD
golataCrebmuN
golataCrebmuN
"78"42"63 4 51 0076H1 7842C1
Special Purpose UnitsArtwork Shelving Open Shelf Filing Record Storage
This efficient unit serves theneed for storing, organizingand protecting artwork. It is abasic piece of storage equip-ment wherever artwork ismaintained. The unit has 18openings, each with a 26-3/4"clear vertical opening. The unitincludes closed back, sidesand base, four Hi-Performance®
shelves and 15 dividers.Dividers adjust easily on 1-1/2"centers. Can be accessorizedwith lockable doors. Order EndKit to finish each unit or row.
Shown in Light Putty (723)enamel. Available in otherstandard Clipper ShelvingColors.
A space-saving efficient unitdesigned for filing a variety ofrecords in a safe, organized,easily accessible system.Special tabbed dividers insertinto the shelf and special backbracket for divider stability.They adjust easily on alternate1" and 2" centers. The unitfeatures closed sides and base.A special bracket at each shelflevel is pierced to accept onetab of the divider. Order EndKit to finish a unit or row.
Shown in Light Putty (723)enamel. Available in otherstandard Clipper Shelvingcolors.
NOTE: Utilizes 18 ga. StandardFlange Shelves only.
An efficient, practical storageunit with a broad applicationthroughout the healthcareindustry for the protectivestorage of X-rays. The unitfeatures Heavy Duty Hi-Performance shelves, closedback, sides, and base. 25dividers are furnished in twosizes which adjust easily on 1-1/2" centers. The dividersattach to the shelf with strongplastic buttons. Order End Kitto finish each unit or row.
Shown in Light Putty (723)enamel. Available in otherstandard Clipper Shelvingcolors.
Refer to opening sizes in chartbelow.
X-Ray Shelving Plan Shelving
Designed with the engineer,draftsman or architect in mind,this unit allows plans anddrawings to be stored eitherrolled or flat. This unit provides64 openings 6" x 36" x 6" forrolled storage and 9 openings48" x 36" x 4" for flat storage.Unit includes Heavy Duty Hi-Performance shelves, closedback, sides and base. Can beaccessorized with lockabledoors. Order End Kit to finisheach row.
Shown in Light Putty (723)enamel. Available in otherstandard Clipper Shelvingcolors.
10
C
Clipper Shelving Components
Box Post Offset Angle Box PostPost Intermediate
1 Box Post 2 Offset Angles 1 Box Post1 Angle Post 1 Side Panel 2 Offset Posts1 Side Panel 1 Side Panel
Deep High Cat. No. Cat. No. Cat. No.12" 87" 15412CC 15412AC 15412BC18" 87" 15418CC 15418AC 15418BC24" 87" 15424CC 15424AC 15424BC
D. Floor Anchor Clip – Heavygauge device punched for fastening poststo floor. Includes hardware to fasten topost. Catalog No. 10006Z
E. Foot Plate – Used to distribute unitload and protect the floor. For box andangle post. Catalog No. 10007Z
Shim, 11 Gauge - (not shown) Foroptional placement beneath Floor AnchorClip. Catalog No. 10011C
Closed Upright AssembliesSteel Panels used to close the sides of 87" high shelving units. Panels are securelywelded to posts for rigidity, helping to reduce installation time and costs.
A & B. Clipper Clips – One piece14 gauge rugged compression clip insertsinto either box or offset angle posts tohold shelf securely while allowing easyremoval if changes are needed.
A — Cat. No. 10002Z - For Hi-Performance ShelvesB — Cat. No. 100001Z - For Standard Flange Shelves
C. Post Splice – Used to join Box orAngle posts for high rise or mezzanineapplications. One per post.Catalog No. 10030H
Box Posts – A high strength rollformed tubular box section usually used atunit fronts; permits full access to shelfwidth. Designed to be used in commonbetween units, or at row ends. Permitsvertical shelf adjustment on 1" centersusing clips or nuts & bolts. Internal flangeis punched on 3" centers to accept sidesway bracing or closed side panels.
Offset Angle Posts – A roll formedhigh strength post which permits 1"vertical shelf adjustment, using clips ornuts & bolts. Can be used at rear of units,or at front and rear. Offset recess addsrigidity and allows for independent shelfclip adjustment. Ends of flanges arepunched on 3" centers to accept swaybraces or closed panels.
14 Ga. 16 Ga.Height Cat. No. Cat. No.
39" 1B4039 –48" 1B4048 –75" 1B4075 –87" 1B4087 1B608799" 1B4099 –123" 1B4123 –147" 1B4147C –
14 Ga. 16 Ga.Height Cat. No. Cat. No.
39" 1A4039 –48" 1A4048 –75" 1A4075 –87" 1A4087 1A608799" 1A4099 –123" 1A4123 –147" 1A4147C –
)sdnuop(-seiticapaCtsoPreppilC.aG41
htgneLdecarbnU elgnAelbuoD
ecapS.xaM()sevlehSneewteB tsoPxoB elgnAelgniS
nodetloB()sretneC"21
"9"21"51"81"12"42
047605460706036509050844
067309430313007208120861
072807670886049509740644
AB
D
E
Box Post Offset AnglePost
Closed Upright Assembly
11
Closed ConstructionBack and Side PanelsPanels to enclose the backs andsides of Closed Type Shelvingprovide unit stability while givinggreater protection to the shelv-ing contents.
Back panels fasten to theflanges of offset angle posts atthe rear of units. The center ofthe back is held tight against ashelf with a "back panel clip"furnished with each back. Com-mon backs may be used whenunits are placed back-to-back,provided that units are securelybolted together.
Backs 36" wide are furnished inone piece through 87" high.Over 87" high, they are split hori-zontally (2 pieces). 42" & 48"wide backs are furnished in onepiece through 51" high; above51" they are split horizontally (2pieces). Hardware included.
Side panels fasten to the flanges in the front and rear posts.Furnished in one piece through 87" high. As an alternate toside panels, you may order Closed Upright Assemblies(shown on the previous page) which combine posts andside panels in one welded unit.
Clipper Shelving ComponentsOpen Construction
Sway BracesSway braces provide stability forOpen Type shelving. They arefurnished in sets of two bracesto fasten to one back or side ofa unit. Hardware included.
Back sway braces eliminatelateral sway. They fasten to theflanges of offset angle postsused at the rear of units. Bracesalso bolt to each other at thecenter hole to ease installation.
Side sway braces eliminate frontto back sway. They fasten to theflanges of the front and rearposts.
)D(slenaPediS
thgieH)sehcni(
)sehcni(htpeDflehS
9.oN.taC
21.oN.taC
51.oN.taC
81.oN.taC
42.oN.taC
03.oN.taC
63.oN.taC
938415577899
----
H04311-
H00411H90411H01411H03411H04411H05411
----
H04511-
H00611H90611H01611H03611H04611H05611
H00711-
H01711H03711H04711H05711
H00811---
H04811H05811
H00911--
H03911H04911H05911
)C(slenaPkcaB
thgieH)sehcni(
)sehcni(htdiWflehS
42.oN.taC
03.oN.taC
63.oN.taC
24.oN.taC
84.oN.taC
9315577899
---
H04321-
---
H04421-
H00521H01521H03521H04521H05521
H00621H01621H03621H04621H05621
H00721H01721H03721H04721H05721
Corner Angle BracesFor applications requiring clear entry to shelves front andrear, Corner Angle Braces may be used. Contact yourPenco representative for pass-thru applications. Notrecommended for two levelshelving. Hardware included.
E. For box posts used in com-mon with two standard flangeshelves. Used at front andrear of unit.
Catalog No. 10044H
F. For angle post only. Use atfront and rear of unit.
Catalog No. 10043H
)A(secarByawSkcaBhtdiWtinU
)sehcni(htgneLllarevO
)sehcni( .oN.taC4203632484
5405
4/3-058/1-752/1-56
A54021A05021H63021H24021H84021
)B(secarByawSediShtpeDtinU
)sehcni(htgneLllarevO
)sehcni( .oN.taC921518142032363
115191624354
4/1-6494
S11021S51021S91021S62021S43021S54021S64021S94021
F
E
B
A C
D
12
Hi-Performance® ShelvesClipper Hi-Performance® Shelves maximize load handlingcapacity through a design which shapes the front and rearflanges into rigid tubular box beams. The box shapeprovides two vertical surfaces in each box-flange thatinherently give it a high strength-to-weight ratio.
The shelves are efficiently manufactured from high strengthcold rolled steel on a modern automated roll forming mill.
For additional strength, flanges of the box beams arewelded to the underside of the shelf on 3" centers. Shelfcorners are lapped and welded.
Shelves are available in a wide variety of sizes shown belowin the capacity chart. All shelves are punched on the faceand surface to accept shelving accessories such asdividers, label holders and bin fronts.
All shelves are supplied with Clipper Clips.All shelf load capacities are in pounds for evenly distributed loads,
and include a safety factor of 1.65.Note: (1): Class 3 capacities are based upon the use of Extra Heavy Duty Shelves with
(A) Side Shelf Supports and(B) Center Support for additional capacity. Must use nuts and bolts for shelves, not clips.
Clipper Hi-Performance Shelf Capacities
ytuDmuideM0ssalC
ytuDmuideMleetShtgnertShgiH
ytuDyvaeH1ssalC
ytuDyvaeHleetShtgnertShgiH
ytuDyvaeHartxE2ssalC
ytuDyvaeHartxEleetShtgnertShgiH
ytuDyvaeHartxE)1(etoNeeS-gnicrofnieRhtiW
DxW .oN.taC yticapaC .oN.taC yticapaC .oN.taC yticapaC yticapaC
"21x"63"51x"63"81x"63"42x"63"03x"63"63x"63
C216322H1C516322H1C816322H1C426322H1
--
005005005005
--
C216302H1C516302H1C816302H1C426302H1C036302H1C636302H1
008008058008005005
C216381H1C516381H1C816381H1C426381H1C036381H1C636381H1
0011001100210521009009
--
0002000200020002
"21x"24"51x"24"81x"24"42x"24"03x"24"23x"24"63x"24
-------
-------
C212402H1C512402H1C812402H1C422402H1C032402H1C232402H1C632402H1
006006006006526525574
C212481H1C512481H1C812481H1C422481H1C032481H1C232481H1C632481H1
0011001105010090001059009
--
00610061006100610061
"21x"84"51x"84"81x"84"42x"84"03x"84"63x"84
C218422H1-
C818422H1C428422H1
--
053-573004
--
C218402H1C518402H1C818402H1C428402H1C038402H1C638402H1
005005005005005005
C218481H1C518481H1C818481H1C428481H1C038481H1C638481H1
057058009009057057
--
0021002100210021
Clipper bins at parts distribution center
B. Class 3 Center Support: Runs left to right beneath themid-point of the shelf for conversion to Class 3. Sup-ported by side shelf supports.
Width Cat. No.36" H13736C42" H13742C48" H13748C
A. Class 3 Side Shelf Support (pairs): Used to sup-port Center Support in Class 3 applications.
Depth Cat. No.18" 1H830H24" 1H840H30" 1H850H36" 1H860H
13
0ssalC B-1ssalC B-2ssalC A-2ssalC
sdaoLlamroNroFlanoitiddaoN.tnemecrofnier
gniriuqeRsdaoLlamroNroFdradnatSA.ecnatsiseRtcapmInoitiddaehthtiwflehS0ssalCnirabgnicrofnier"8/1x"1afo
.egnalftnorfeht
.sdaoLmuideMroFhtiwB-1ssalCsaemaS
afonoitiddaehtraerehtnirabgnicrofnier
.egnalf
.sdaoLyvaeHotmuideMroFehthtiwflehs0ssalCdradnatsA
"8/1x"1x"1dellatsnidleiffonoitiddaraerdnatnorfniselgnagnicrofnier
.segnalf
eziSflehSDxW
0ssalC.oN.taC
tAnoitcelfeDtnorFretneC
egdE yticapaC yticapaC yticapaC
"21x"42"81x"42"42x"42
C01821C03821C04821
"002."002."002.
09901110411
072103410901
085103410901
"21x"03"81x"03"42x"03
C01921C03921C04921
"052."052."052.
067028029
08906010301
032102310301
"9x"63"21x"63"51x"63"81x"63"42x"63"03x"63"63x"63
C00031C01031C02031C03031C04031C05031C06031
"003."003."003."003."003."003."003.
026026026066007097047
sevlehs,1ssalCeromylbaicerppaevahtonod
seitilibapacgniyrracdaol,0ssalCrevo
desuebdluohstubrotcapmierehwsdaoldetartnecnoc
.egdetnorfehtgnolarucco
097018028058029068047
0890101020105010901068047
"21x"24"51x"24"81x"24"42x"24"03x"24"63x"24
C01131C02131C03131C04131C05131C06131
"053."053."053."053."053."053.
025025055085026086
096096017047008047
058068088039008047
"21x"84"81x"84"42x"84"03x"84"63x"84
C01231C03231C04231C05231C06231
"004."004."004."004."004.
054074084015055
095006046076027
047077097038027
Conventional Flange ShelvesClipper Conventional Flange Shelves are fabricated from 18 gauge cold rolled steel. All sides of the shelf are doubleflanged for added strength. The corners are lapped and welded for positive reinforcement. Shelves secure to posts withPenco's unique compression Clipper clip, or can be bolted. Shelves are punched laterally for divider placement on alter-nating 1" and 2" centers.
A - Reinforcing Bar: Rolled steel barsinsert in the shelf channel for reinforce-ment. Hardware is included.
Wide Deep High Cat. No.30" 1/8" 1-3/32" 16660H36" 1/8" 1-3/32" 16670H42" 1/8" 1-3/32" 16680H48" 1/8" 1-3/32" 16690H
All shelves are supplied with Clipper Clips. Nuts and bolts may be substituted upon request. All capacities are forsafe static loads distributed uniformly over the entire shelf surface as determined by test. Refer all "Pass Thru" or
other unusual conditions to Penco Engineering for their evaluation.
Clipper Conventional Flange Shelf Capacities - 18 Gauge
B
A B - Reinforcing Angle: 1/8" thick rolledsteel angles added to the shelf flangesfor developing class 2A shelves. Hard-ware is included.
Wide Deep High Cat. No.36" 1" 1" 16520H42" 1" 1" 16530H48" 1" 1" 16540H
Clipper shelvingused for records storage
14
Swinging Doors
3 Point latching withlocking handle and 2keys.
NOTE: Not for use withModular Drawers.
Doors are pre-hung atthe factory on a welded
frame for easy assembly and good fit.Can be used on standard ledge or counterunits up to 87" high. Order doorsseparately from units. Door can beattached to box posts or angle posts.Base strips should be ordered to close theopening between the door frame and thefloor.
Door Frame Unit PairWidth Height Height Cat. No.
(For Below Ledge or Counter Height)36" 36" 39" 19600H
(For Above Ledge Unit)36" 48" 48" 19610H
(For Standard Shelving Units)36" 73" 75" 19630H36" 85" 87" 19640H
48" 36" 39" 19646H48" 85" 87" 19650H
Sliding Doors
Flanged on all 4 sides and reinforced.Doors slide on quiet, smooth-running nylonrollers and guides. Designed for use withtwo 36" wide units side by side. Completewith grooved key cylinder lock and 2 keys.Hardware included. Not for use withModular Drawers.
Door Frame Unit PairWidth Height Height Cat. No.72" 36" 39" 1H90723672" 84" 87" 1H907284
Clipper Shelving AccessoriesD - Full Height Dividers: Used todivide a shelf opening into smaller units.Divider has a beaded front edge forstrength and safety. Hardware included.Note: for Class 3 shelving applications,contact your representative regardingspecial notching of dividers.
Deep High Cat. No.12" 6" 15600H12" 9" 15620H12" 12" 15640H12" 14" 15650H12" 18" 15670H
15" 6" 15700H15" 12" 15740H
18" 6" 15800H18" 9" 15820H18" 10" 15830H18" 12" 15840H18" 16" 15860H18" 18" 15870H18" 24" 15890H
24" 6" 15900H24" 9" 15920H24" 12" 15940H24" 18" 15970H24" 24" 15990H
36" 18" 16170H
E - Label Holders: A formed steelstrip that accepts 7/8" labels. Fastens tothe shelf with plastic buttons (included).
Width Cat. No.24" 13900H30" 13910H36" 13920H42" 13930H48" 13940H
Front Base Strip
Closes the space between the floor andbottom shelf. Hardware included.
Wide High Cat. No.24" 3" 14500H30" 3" 14510H36" 3" 14520H42" 3" 14530H48" 3" 14540H
A - Bin Front: A formed steel panelpartially enclosing the front opening of ashelf to keep bulk items within a bin.
Wide High Cat. No.36" 1" 14210H36" 2" 14220H36" 3" 14230C42" 3" 14330C48" 3" 14430C
1" & 2" Bin Fronts attach to the front of the shelfwith bolts & nuts. Hardware included.
3" high Bin Front attaches to posts with metalclips. Hardware included.
B - Sliding Divider: Formed to fitaround front and rear flanges on the shelf.Position anywhere on surface. Nohardware needed.
For Hi-Performance Shelves
Deep High Cat. No.12" 4" 1H4124C12" 6" 1H4126C18" 4" 1H4184C18" 6" 1H4186C24" 4" 1H4244C24" 6" 1H4246C
C - Partial Dividers: Partiallysubdivides shelf to separate stored items.Hardware included.
Deep High Cat. No.12" 2" 16395H12" 4" 16410H18" 2" 16397H18" 4" 16430H24" 4" 16440H
A
BC
E
D
15
Finished End Panel
Formed sheet steel panels used to finishthe end of a shelving row.Panels attach to posts to coverholes and hardware. Presentsan attractive and finishedappearance.
Deep High Cat. No.12" 87" 18241H18" 87" 18440H24" 87" 18540H
Must be used with Box Post atfront, Angle Posts at rear.
Multi-Level Support Brackets
For attachment of cross aisle deckingsupports. Bolts to shelvingposts.
A – For Box PostCat. No. 10063H
B – For OffsetAngle PostCat. No. 10062H
Coat Rod Bracket
A metal channel "V" groved to accept a1-1/16" O. D. pipe for hanging clothes orother material. Attaches to front and rearposts. Two required per coat rod.
Wide High Cat. No.18" 1-3/4" 14705H24" 1-3/4" 14706H
Coat Rod – 3/4" Galv. Pipe 1-1/16" O. D.36" 9405C48" 9406C
Shelf Boxes
This strong compact open topped boxmeasures 4-5/8" high and is ideal forstoring small parts where shelves arespaced on 6" centers. It features a fullwidth drawer pull, built-in drawer stop andrecessed label holder. Box guides areprovided for each row of boxes. Finishedin 028 Gray only. Order 2 Shelf BoxGuides for each shelf of boxes.Cat. No. 10038H.
Box Size Boxes Per
w x d Cat. No. 36" Shelf5-5/8" x 11" 38030 68-7/16" x 11 38035 411-1/4" x 11" 38040 3
5-5/8" x 17" 38180 68-7/16" x 17" 38185 411-1/4" x 17" 38190 3
5-5/8" x 23" 38255 68-7/16" x 23" 38260 411-1/4" x 23" 38265 3
Clipper Shelving Accessories
Closed Clipper Shelving with sliding dividersused for storage of medical records.
A
B
Shelf Box DividersDividers have built-in label holders anddrop into slots in the box sides.Adjustment on 1" centers allow you tocompartmentalize each box. Galvanizedfinish.
Sizew x h Cat. No.
5-5/8" x 4-1/2" 383068-7/8" x 4-1/2" 3830711-1/4" x 4-1/2" 38308
Automotive parts warehouse with two levelshelving and full height dividers
16
GENERAL: All shelving shall comply with SMA and ANSI MH 28.1-1982and in addition shall have the following characteristics:
POSTS: All posts shall be punched for clip or nut and bolt construction.Shelves and accessories are to be vertically adjustable on 1" centers. Sidesway braces or side panels to be attached to the side flange of the post.Bolts, nuts, and sway braces or panels shall not obstruct the full adjustabilityof the shelves.
BOX POST: Box post to be roll formed and have overall dimensions of 3/4" wide x 2-7/16" deep. Box post to be flush within 1/4" of the face of theshelves when assembled.
OFFSET ANGLE: Offset angle post shall be roll formed and have overalldimensions of 1-1/8" wide x 2-1/2" deep. The rear flange shall be punchedto accept sway braces or backs, the side flange shall be punched to acceptside sway braces or side panels.
SIDE PANELS: Shall be 24 gauge steel. Each side shall be punched withholes for bolting to posts.
BACKS: Shall be 24 gauge steel with holes on each side for bolting toangle posts and in the middle for using a back panel clip.
SWAY BRACES: To be 12 gauge x 3/4" steel punched at each end forbolting to posts and at the center for strength and ease of assembly
CLIPPER SHELF CLIP: One piece 14 gauge rugged compression type toinsert into either box or offset angle posts to form a positive four pointconnection. Clips shall have two claw-like hooks to seat firmly into postslots and two tabs at bottom to seat into post holes for a tight frictionconnection. All clips for all posts and shelves to be the same. Design shalloffer a pre-clipping feature to simplify erection. Finish: zinc plated. Allshelves are to have four independently adjustable clips.
SHELVES: CONVENTIONAL FLANGE, CLASS “O”: Shall be 18 gaugesteel with a 1-3/16" vertical face on all four sides, front and rear faces tohave 17/32" return flange 90o with the edges coined upward to preventsnagging. Sides to have a 5/8" return flange 90o. All four shelf cornersshall be closed by lapping and spot welding together to provide a firm,rigid shelf. Shelf shall be universally punched for use with all availableaccessories and for clip or bolted assembly. Shelves are available in 24",30", 36", 42" and 48" widths and 9", 12", 15", 18", 24", 30" and 36" depths.Shelves can be reinforced by adding 1-3/32" x 11 ga. bars or 1" x 1" x 1/8" angles to front and back flanges.
SHELVES: CLIPPER HI-PERFORMANCE® BOX FORMED: MediumDuty, Heavy Duty and Extra Heavy Duty are manufactured from cold rolledsteel in three material thicknesses that provide up to three different shelfcapacities per size. Shelves have 1-1/4" face on all four sides. Front andrear faces have four 90o bends providing a 3/4" x 1-1/4" high tubular shapewith an 11/16" wide flange seated against the underside of the shelf. Theflange is spot welded to the underside of the shelf on 3" centers. Sideshave a 5/8" return flange 90o. All four corners are closed by lapping andspot welding together. Medium Duty and Heavy Duty shelf tabs for lappingand welding have formed ribs to maintain the same snug fit in the shelf clipas the extra heavy duty shelf. Overall, the shelf depth and width is 1/4"less than nominal. The shelf is punched for divider adjustment on 1-1/2"centers and for attachment of label holders, bin fronts and base fronts. Hi-Performance shelves are available in 36", 42", & 48" widths and 12", 15",18", 24", 30" & 36" depths.
Extra Heavy Duty Reinforced (Class 3) Hi-Performance Shelves providemaximum capacity using Extra Heavy Duty shelves that are reinforced us-ing 13 gauge side shelf supports bolted to the Clipper posts and 14 gauge1-5/32" high hat shaped center supports held in place by a notch andflange in the side shelf support.
LEDGE TOPS: To be 14 gauge steel. Face of ledge to be 1-1/8" and havea center reinforcing pan. Ledge top to project 1-1/8" beyond the face of thepost and to have two 14 gauge angles welded to underside for strengthand bolting to post. Must be used with box posts below ledge.
LEDGE ENDS: To be manufactured from 14 gauge steel and furnished togive ledge top a finished appearance.
COUNTER TOPS: To be 14 gauge steel. Face of counter top to be 1-1/8"and project 1-1/8" beyond face of post with a welded center reinforcingpan. Units to be furnished with box post front and rear for finished appear-ance. 14 gauge counter top ends can be furnished at the ends of all rowsfor a finished appearance.
COUNTER FRONT: To be 18 gauge steel attached with no exposed fas-teners.
BASE STRIP: Shall be 18 gauge steel attached to face of shelf with boltsand nuts to close space between the bottom of the shelf and the floor.
LABEL HOLDER: Shall be 24 gauge steel with necessary holes for attach-ing to shelves with plastic push-in fasteners.
SHELF DIVIDERS: 6" high through 20" high shall be 24 gauge, 24" highand over shall be 20 gauge. All divider front flanges shall have a 5/16"diameter bead. Top, bottom and rear flanges are 7/8". Dividers less than24" high shall be attached with plastic push-in fasteners, 24" and higher arebolted.
PARTIAL DIVIDERS: Shall be 18 gauge steel with a 7/8" flange at thebottom. Attached with push-in Plastic Button fasteners.
SLIDING DIVIDER: To be 20 gauge steel manufactured to give infinitelateral adjustability. Divider portion shall be sloped 45o at front, 1/2" radiusat front corner.
BIN FRONTS: To be 18 gauge steel. One and two inch high bin frontsshall be bolted to the face of the shelf. Three inch high bin fronts to beattached to the post by use of 16 gauge zinc plated channel clips.
SHELF BOXES: To be 20 gauge steel with a rigid curled handle at thefront of the box, punched with an integral card holder on front and rear. Boxshall be 4-5/8" high to fit between shelves on 6" centers and shall be slot-ted to accept dividers on 1" centers.
SHELF BOX DIVIDERS: To be 20 gauge steel. Punched with an integralcard holder.
SWINGING DOORS: Consist of a 16 gauge steel frame and 20 gaugedoors, reinforced to prevent warping. Doors are riveted to three 5-knucklehinges and have a three-point latching device with chrome plated key lockhandle. Doors to be preassembled in the frame at factory.
SLIDING DOORS: Set of doors is 72" wide and cover two 36" wide units.Each door shall be 22 gauge with two or more 18 gauge reinforcing pans,recessed handle and nylon glides and rollers. Each set has16 gauge chan-nels welded at the top and bottom, and 20 gauge channels on the ends.Doors shall be contained in top, bottom and vertical channels. Right handdoor has a provision for a cylinder lock.
FOOT PLATES: Shall be 13 gauge zinc plated steel and be used to pro-tect floors.
FINISH: All painted parts shall be selected from a minimum of five stan-dard colors. Materials shall be cleaned and phosphatized in a multi-stageprocess, dried in a 400o oven and electrostatically spray painted with ahigh grade enamel and baked on at 360o.
Clipper® and Hi-Performance® are registered trademarks of Penco Products, Inc.
PENCO RESERVES THE RIGHT TO VARY SPECIFICATIONS CONSISTENT WITH OUR POLICY OF CONTINUOUS PRODUCT IMPROVEMENT.
Clipper ® Specifications
17
Heavy Duty Modular DrawersThe Cubic Advantage
How To Order Modular DrawersFor Shelving
A. The easiest way to order Clipper Heavy DutyModular Drawers is by selecting the Drawer Kitthat matches your needs, and then add theappropriate Drawer Interior Subdivision.
B. If you need to order from parts and accessories:1. Select the size of mounting brackets. 2.Order drawer front sizes that add up to thebracket size. 3. Order one shelf closure stripper mounting bracket kit. 4. Order partitions ÷rs, plus any accessories sized to fit yourapplication.
C. Color: Drawers, brackets and carriage arefinished in Putty 3. Partitions are Gray.
NOTE: We strongly recommend that shelving be flooranchored, wall anchored, or cross aisle top tied. For FloorAnchoring Clip order Catalog Number 10006Z.
NOT FOR USE WITH SHELVING DOORS.
MountingBrackets
Heavy Duty Modular DrawersProvide secure high density storage of smallparts. Heavy duty 100% full suspension allowsfull view of contents. Available in a variety ofsizes with a wide range of accessories. Can beadded to existing shelving installations.
• For 36" WideClipper Shelving
Units
• Available for18" & 24" depths
• 400 lb. capacity per drawer
• Improve inventory control
• Increased versatility
• Reduce stockroom labor
• Reduce inventory damage
• Improved security
• Economy through accessibility
• Efficient space utilization
With Clipper® Heavy Duty Modular Drawers inshelving you can effectively utilize your storagespace above as well as below your drawers. Byconsolidating your bulk storage needs in thesame floor space taken up by a conventionaldrawer cabinet unit, you can increase yourstorage capabilities up to 40% or more! PencoModular Drawers can be installed at any level,and can be moved if your needs change. If youneed drawers, your present Clipper shelvinginstallation can be retrofitted right now withoutthe capital expense of new shelving or cabinets.
Best of all, Penco Modular Drawers are trulymodular. All heights and adjustments are on 1"centers, drawers can be interchanged andswitched (2-3" drawers replace a 6" drawer etc.).The wide variety of sizes and drawer subdivisionpossibilities make this system versatile enoughto fill practically any need.
Can be used in units with either Hi-Performanceor Standard Flange Shelves.
Drawer
DrawerCarriage
Carriage Rail
18
Heavy Duty Modular DrawersModular Drawer Kits
All Clipper Modular Drawer Kits come complete with mount-ing brackets, drawer, carriage, rails, hardware and shelf clo-sure strips necessary to install easily into new or existingClipper shelving. All are available for 18" and 24" deepshelving. Drawer combinations shown are representative ofthe most popular configurations. See the Componentspage to design drawer combinations not shown.
Three Drawer KItOverall Height – 12"
18" Deep 24" DeepCat. No. Cat. No.1MK601P 1MK602P
Six Drawer KItOverall Height – 24"
18" Deep 24" DeepCat. No. Cat. No.1MK605P 1MK606P
NOTE: All overall heightdimensions do not includethe shelves placed at thetop and bottom of thedrawers.
Eight Drawer KItOverall Height – 36"
18" Deep 24" DeepCat. No. Cat. No.1MK613P 1MK614P
Seven Drawer KItOverall Height – 36"
18" Deep 24" DeepCat. No. Cat. No.1MK609P 1MK610P
Four Drawer KItOverall Height – 12"
18" Deep 24" DeepCat. No. Cat. No.1MK603P 1MK604P
Six Drawer KItOverall Height – 24"
18" Deep 24" DeepCat. No. Cat. No.1MK607P 1MK608P
Seven Drawer KItOverall Height – 56"
18" Deep 24" DeepCat. No. Cat. No.1MK611P 1MK612P
Eleven Drawer KItOverall Height – 56"
18" Deep 24" DeepCat. No. Cat. No.1MK615P 1MK616P
B
Interior Subdivisions
Calculating CompartmentDimensions
The slots in all sides of each drawer are on nominal 1" centers(.97"). Partitions, which are inserted from front to rear, have thesame slot pattern as the sides. The diagram below enables youto figure the exact compartment sizes of interior subdivisions.
Number of Spaces
Number of Spaces
Depth of Compartments
B = (number of spaces x 0.9688") *
* Subtract 1/4" each for compartments at thefront and rear.
Compartment Width
A = (number of spaces x 0.9688") – 0.500"
A
19
Organized storage of small parts is achieved by dividingthe drawer body into smaller compartments. Illustrated arethe most common configurations. To customize your owndrawer compartments, order partitions and dividers
Interior Subdivisions For 24" Deep Shelving
4 CompartmentsDrawer Front
Height Cat. No.3" 1MD0694" 1MD0715" 1MD0706" 1MD0728" 1MD073
6 CompartmentsDrawer Front
Height Cat. No.3" 1MD1034" 1MD1055" 1MD1046" 1MD1068" 1MD107
8 CompartmentsDrawer Front
Height Cat. No.3" 1MD0754" 1MD0775" 1MD0766" 1MD0788" 1MD079
9 CompartmentsDrawer Front
Height Cat. No.3" 1MD1114" 1MD1085" 1MD1276" 1MD1098" 1MD110
10 CompartmentsDrawer Front
Height Cat. No.3" 1MD0434" 1MD0455" 1MD0446" 1MD0468" 1MD047
12 CompartmentsDrawer Front
Height Cat. No.3" 1MD0814" 1MD0835" 1MD0826" 1MD0848" 1MD085
15 CompartmentsDrawer Front
Height Cat. No.3" 1MD0494" 1MD0515" 1MD0506" 1MD0528" 1MD053
16 CompartmentsDrawer Front
Height Cat. No.3" 1MD0874" 1MD0895" 1MD0886" 1MD0908" 1MD091
20 CompartmentsDrawer Front
Height Cat. No.3" 1MD0554" 1MD0575" 1MD0566" 1MD0588" 1MD059
24 CompartmentsDrawer Front
Height Cat. No.3" 1MD0924" 1MD0945" 1MD1286" 1MD095
25 CompartmentsDrawer Front
Height Cat. No.3" 1MD0614" 1MD0635" 1MD0626" 1MD0648" 1MD065
30 CompartmentsDrawer Front
Height Cat. No.3" 1MD0664" 1MD0675" 1MD1296" 1MD068
32 CompartmentsDrawer Front
Height Cat. No.3" 1MD0964" 1MD0975" 1MD1306" 1MD098
40 CompartmentsDrawer Front
Height Cat. No.3" 1MD0994" 1MD1015" 1MD1316" 1MD102
48 CompartmentsDrawer Front
Height Cat. No.3" 1MD093
Interior Subdivisions For 18" Deep
Heavy Duty Modular Drawers
Drawer Interior with Plastic Bins
36 Plastic BinsDrawer Front
Height Cat. No.3" 1MD1244" 1MD126
72 Plastic BinsDrawer Front
Height Cat. No.3" 1MD1204" 1MD122
24" Deep
18" Deep
6 CompartmentsDrawer Front
Height Cat. No.3" 1MD0134" 1MD0155" 1MD0146" 1MD0168" 1MD017
15 CompartmentsDrawer Front
Height Cat. No.3" 1MD0254" 1MD0275" 1MD0266" 1MD0288" 1MD029
8 CompartmentsDrawer Front
Height Cat. No.3" 1MD0194" 1MD0215" 1MD0186" 1MD0228" 1MD023
18 CompartmentsDrawer Front
Height Cat. No.3" 1MD0314" 1MD0335" 1MD0326" 1MD0348" 1MD035
54 Plastic BinsDrawer Front
Height Cat. No.3" 1MD1124" 1MD114
27 Plastic BinsDrawer Front
Height Cat. No.3" 1MD1164" 1MD118
separately. Compartment dimensions are clear openingsizes. Catalog numbers are provided for convenientordering of partitions and dividers only. Order drawersseparately. Partitions and dividers are not factory installed.
20
Label HolderAttaches todivider. Accepts2-1/4" wide x 3/4"label.
Cat. No. 1M0009
Modular Drawers
All drawers are furnished completewith a heavy duty roller bearing car-riage, carriage rails, extruded alumi-num pull with built-in label holder, la-bel, clear acetate label cover andhardware. Capacity is 400 pounds,evenly distributed.
18" Deep ShelvingInterior Dimensions: 30" w. x 15" d.
24" Deep ShelvingInterior Dimensions: 30" w. x 21" d.
Drawer Drawer Usable 18" 24"Front Body Drawer Deep Deep
Height* Height Height Cat. No. Cat. No.
3" 1-1/2" 2" 1MD301P 1MD307P4" 2-1/2" 3" 1MD302P 1MD308P5" 3-1/2" 4" 1MD303P 1MD309P6" 4-1/2" 5" 1MD304P 1MD310P8" 6-1/2" 7" 1MD305P 1MD311P
* Actual height 1/16" less.
Mounting Bracket Kit
Includes four bracketsand hardware forfastening to shelvingposts.
Height Cat. No.
12" 1MK112P18" 1MK118P24" 1MK124P36" 1MK136P
Shelf Closure Strip
A finish trim strip which fastens to theshelf and closes the gap above thetop drawer.
Size Cat. No.2" 1M137H
Partitions
Runs from front to rear to separatedrawer left to right. Accepts dividers inpre-punched slots.
DrawerShelving Front
Depth Height Cat. No.18" 3" 1M336H18" 4" 1M339H18" 5" 1M338H18" 6" 1M342H18" 8" 1M345H
24" 3" 1M337H24" 4" 1M340H24" 5" 1M341H24" 6" 1M343H24" 8" 1M347H
DividersZinc plated dividersinsert into slots foreasy adjustment.
Drawer No. ofFront Slots
Height Wide Cat. No.3" 4 1M03313" 5 1M03323" 6 1M03333" 7 1M03343" 8 1M03353" 10 1M03373" 11 1M0338
4" 4 1M03474" 5 1M03484" 6 1M03494" 7 1M03504" 8 1M03514" 10 1M03534" 11 1M0354
5" 4 1M03395" 5 1M03405" 6 1M03415" 7 1M03425" 8 1M03435" 10 1M03445" 11 1M0345
6" 4 1M03566" 5 1M03576" 6 1M03586" 7 1M03596" 8 1M03766" 10 1M03786" 11 1M0379
8" 4 1M03818" 5 1M03828" 6 1M03838" 7 1M03848" 8 1M03858" 10 1M03868" 11 1M0388
*NOTE: If more than one set of brackets isused in a single shelving unit, contact yourPenco representative for applicable lockingmechanism.
Drawer Locking MechanismContains twokeyed alike built-incylinder locks andprevents drawersform beingopened. Suppliedwith two keys.*
MountingBracketHeight Cat. No.
12" 1MK41218" 1MK41824" 1MK42436" 1MK436
Components & AccessoriesPlastic Bins
Sturdy gray molded plastic bin forsmall parts has built-in label holder.
Drawer NominalFront DimensionHeight w x d x h Cat. No.
3" 2-1/2" 2-1/2" 1-1/2" 1M00013" 2-1/2" 5" 1-1/2" 1M00023" 5" 5" 1-1/2" 1M0003
4" 2-1/2" 2-1/2" 2-1/2" 1M00044" 2-1/2" 5" 2-1/2" 1M00054" 5" 5" 2-1/2" 1M0006
21
Clipper Applications
40' high shelving ready for loading.High density record storage.
Industrial parts warehouse makes gooduse of shelving with bins.
Two level automotive parts storage.
Upper level of retail mail order central warehouse.Automobile parts distribution center.
Archives records storage. Multi-level shelving with open deck above second level.