Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Product Catalog
CHUMMY Enterprise CO., LTDTel: +886-2-2222-1943
Fax: +886-2-2222-5943Email: [email protected]
Website: WWW.CHUMMYDECAL.COM
Sticker Self-Adhensive
SubstrateSuitable for metals, composites, woods, and plastics.
Feature-Low cost, durable, easy to apply to various substrates.-Transfer carrier reinforce stickers for more complex and difficult posi-tioning.
一般自黏標
特性價廉物美,使用方便,適用於各種產品。材質柔軟可貼於彎曲或弧形表面
適用材質金屬、複合材料、木材、塑膠等
Brushed Metal & Laser Substrate
Suitable for metals, composites,
woods, and plastics.
FeatureModern pattern with metallic, shiny, and hologram colors.
Sticker 拉絲&雷射 自黏標
適用材質金屬、複合材料、木材、塑膠等
特性炫麗的多彩雷射效果或具現代感之電鍍金屬色澤
3-D Substrate
Suitable for metals, composites, woods, and plastics.
Feature-3D effect, enforce quality of prod-ucts-Soft enough to be attached on curved surface
Sticker 3D自黏標
適用材質金屬、複合材料、木材、塑膠等
特性浮雕立體效果,增加產品質感質地柔軟可貼於有彎度之表面
Water TransferHeat Resistant
SubstrateSuitable for carbon, powder coating, aluminium, titanium, anodic coating, metals, composites, wood, and plas-tics
Feature-Super thin, great adhesion, can use either clear coating or non-clear coat-ing.-Suitable for more complex, larger re-dian and larger dimension decals.-Bake it at either high or low tempera-ture.
適用材質碳纖維、粉體塗裝、鋁合金、鈦合金、楊極、金屬、複合材料等
一般撕膜標
特性-超薄、高附著力-適應較複雜與弧度較大、面積較大的圖案-可選擇噴金油或不噴金油-可用高溫或低溫烘烤
LaserWater Transfer
雷射撕膜標
SubstrateSuitable for carbon, powder coating, aluminium, titanium, anodic coating, metals, composites, wood, and plas-tics.
Feature-Super thin, great adhesion, can use either clear coating or non-clear coat-ing.-Suitable for more complex, larger re-dian and larger dimension decals.-Bake it at either high or low tempera-ture.-Silver metal effect, the decal inoforce the beauty of a frame.
適用材質碳纖維、粉體塗裝、鋁合金、鈦合金、楊極、金屬、複合材料等
特性-超薄、高附著力-適應較複雜與弧度較大、面積較大的圖案-可選擇噴金油或不噴金油-可用高溫或低溫烘烤-商標呈現銀絲效果,瞬間加強車架辨識度
Brushed Metal
SubstrateSuitable for carbon, powder coating, aluminium, titanium, anodic coating, metals, composites, wood, and plas-tics.
Feature-Super thin, great adhesion, can use either clear coating or non-clear coat-ing.-Suitable for more complex, larger re-dian and larger dimension decals.-Bake it at either high or low tempera-ture.-Silver metal effect, the decal inoforce the beauty of a frame.
Water Transfer拉絲撕膜標 適用材質
碳纖維、粉體塗裝、鋁合金、鈦合金、楊極、金屬、複合材料等
特性-超薄、高附著力-適應較複雜與弧度較大、面積較大的圖案-可選擇噴金油或不噴金油-可用高溫或低溫烘烤-商標呈現銀絲效果,瞬間加強車架辨識度
3-D
SubstrateSuitable for carbon, powder coating, aluminium, titanium, anodic coating, metals, composites, wood, and plas-tics
Feature-Super high adhesion, can use clear coating or non-coating, paint or non-paint.-3D, the substrate will have extrusion molding effect after paint.
Water Transfer3D 撕膜標
適用材質碳纖維、粉體塗裝、鋁合金、鈦合金、楊極、金屬、複合材料等
特性-超黏, 可選擇上光,不上光,局部上光-3D效果在噴漆後可呈現出立體突出品牌特色
Heat Resistant BC Solvent TransferBC 標
SubstrateSuitable for carbon, powder coating, aluminium, titanium, anodic coating, metals, composites, wood, and plas-tics
Feature-Super thin, great adhesion, can use either clear coating or non-clear coat-ing.-Suitable for more complex, larger re-dian and larger dimension decals.-Bake it at either high or low tempera-ture.
適用材質碳纖維、粉體塗裝、鋁合金、鈦合金、楊極、金屬、複合材料等
特性-超薄、高附著力-適應較複雜與弧度較大、面積較大的圖案-可選擇噴金油或不噴金油-可用高溫或低溫烘烤
How to apply 黏貼方式
Water Tranfer 撕膜標
1. 將商標浸泡純水30秒
2. 等待離型後,貼於車架上
用刮板將水與氣泡刮乾
3. 靜置30分鐘
作80-90度的烘烤,車架即可噴漆
4. 再將撕膜標的膜撕去,噴上金油,
再以130-150度烘烤,粉體金油控制
於180度以上,如果是碳纖車架或塑
膠材質,則需以70-80度烘烤即告完成
BC Solvent BC標
1. 準備BCS, (比例BCS:水)為1:20
水溫維持在30度到40度內
2. 將保護用的離型紙去除,
浸泡在溶劑中10到20秒
3. 將整張貼標移到被貼物上,
以刮刀將貼紙內的水和氣泡刮乾
4. 用清水清洗后以70-100度烘烤20分
鐘,噴上金油後再以150度烘烤,粉體金
油需用195度以下烘烤,如果是碳纖車
架或塑膠材質,則需以70-80度烘烤即
告完成
1. Remove the separator and soak the transfer in the water for 30 seconds.
2. Place the decals on an object. Press down transfer sheet with a rubbersqueegee firmly for excluding extra water and air.
3. Wait for 30 minutes and cure it at 70 degrees to 80 degrees then paint.
4. Take off masking then spray on clearcoating and cure it at 130 degrees -150 degrees for liquid coating, at least 180 degrees for powder coating,or at 70-80 degrees for carbon or plasticsubstrate.
1. Mixing BC Solvent with water (1:20), keep tem-perature at from 30 degrees to 40 degrees.
2. Remove the separator sheet and soak the transfer in BC Solvent for 10 to 20 seconds.
3. Place the decal on the substrate. Press downtransfer sheet with a rubber squeege firmly for excluding extra water and air.
4. Rinse with water. Cure it at from 70 degrees to 100 degrees for 20 minutes then spray on clearcoating and cure it at 150 degrees for liquid painting, up to 195 degrees for powder coating,or at 70-80 degrees for carbon or plasticsubstrate.
CHUMMY Enterprise CO., LTDTel: +886-2-2222-1943
Fax: +886-2-2222-5943Email: [email protected]
Website: WWW.CHUMMYDECAL.COM