Procraft Rigging Products - Pro Sling & Safety · Pro Sling & Safety Inc. Procraft Rigging Products Never Exceed Working Load Limit. It is the users responsibility to determine the

PRO SLING & SAFETY INC.

Procraft Rigging Products

Lift with Experience

Pro Sling & Safety Inc. Procraft Rigging Products

2

Load Rated Shackles...............................................3,4 & 5Non Load Rated Shackles.................................................6Trawl Shackles...................................................................6Stainless Steel Shackles....................................................7Drop Forged Wire Rope Clips...................................8 & 9Malleable Wire Rope Clips...............................................9Heavy Duty Wire Rope Thimbles...................................10 Light Duty Wire Rope Thimbles.....................................11 Tube Thimbles.................................................................11Aluminium Wire Rope Sleeves..............................12 & 13Aluminium Button Stops.................................................13Copper Wire Rope Sleeves & Button Stops....................14Choker Hooks & Knobs..................................................15Alloy Eye Hooks.............................................................16Swivel Alloy Hooks........................................................17Replacement Latch Kits..................................................17Barrel Hooks....................................................................18Pear Links........................................................................18Round Rings....................................................................18Eyebolts...........................................................................19Shoulder Nut Eyebolts.....................................................21Machinery Eyebolts.........................................................22Eyenuts............................................................................22Padeyes............................................................................23Screw Eyebolts (Lag)......................................................23Timber Washers...............................................................23Turnbuckles............................................................24 & 25Snatch Blocks........................................................26 & 27Yarding Blocks................................................................28Off Road Blocks & Sheaves............................................29Load Securement.............................................................30Grade 70 Transport Chains..............................................31Grade 70 Hooks - Grab, Slip & Latched Slip........31 & 32Loadbinders (Cinches) - Ratchet & Lever......................33Winch Straps & Accessories...........................................34Ratchet Tie Down Straps.................................................35Commercial Grade Chains..............................................36Stainless Steel Chain.......................................................37Long Link Mooring Chain..............................................37Connecting Links - Lap, Missing, Twin, Double...38 & 39Quick Links & Snap Links..............................................40Snap & ‘S’ Hooks............................................................41Danforth Anchors............................................................41Sledge Hammers..............................................................42Rafting Dogs...................................................................43Wire Rope Staples...........................................................43

Index


3 Never Exceed Working Load Limit. It is the users responsibility to determine the suitability of the equipment for its intended use. Incorrect use of shackles can cause death, serious injury, or property damage.

GALVANIZED LOAD RATED SHACKLES are used extensively for lifting in static environments as removable links to connect all types of slings to fittings and attachments. Shackle TypesAnchor type shackles are generally used on multi-leg systems or where more space at the top is required. Chain Shackles are generally used on single leg assemblies only. However, in most circumstances chain and anchor shackles are interchangeable. Screw Pin Shackles should be used in applications where they need to be connected and disconnected frequently. However, NEVER use them in long term or permanent applications, or where there is a chance that the load may rotate the pin. Please use Bolt Type (Safety) Shackles in these types of applications.Procraft shackles are hot dipped galvanized and meet or exceeds US Fed Spec RR-C-271 Type IVA Class 2 Grade A and ASTM B30.26. Working Load Limits (WLL) are marked on all shackles, and the factor of safety is 6:1. The WLL marked on shackles is for in line loading, angular loading should be avoided wherever possible. Manufacturers traceability code is forged on the pin and body for easy identification.Rigging PracticesWhen installing screw pin shackles make sure that the pin is fully engaged and the collar makes contact with the shackle body, a wrench or screw driver can be used to lock the pin. If you are using a safety pin shackle make sure the nut is secured and the cotter pin is in good condition and inserted correctly. Check that the pin has penetrated the entire length of the threaded eye, if it does not remove from service as you may have a bent pin or incorrect pin for the shackles. When using screw pin shackles for an extended time the pin should be moused or secured to the body of the shackle, this will prevent the pin from backing out.Make sure that you have selected the correct shackle for your application and that the shackle’s working load limit will not be exceeded. Contact with any sharp edges should be avoided. The load applied to the shackle should be centered in the bow of the shackle to prevent side loading. If side loading is to occur the following reductions should be considered:0 Deg - 100% of marked working load limit45 Deg - 30% reduction on marked working load limit90 Deg - 50% reduction on marked working load limitOver 90 Deg is not recommendedMultiple leg slings should never be applied to the shackle pin, place the shackle pin in the hook. When shackles are used with multi leg slings the angle should never exceed 120 deg included angle, and consideration should also be given to the effect of the angle between the legs. As the horizontal angle decreases so does the load on the sling leg and shackle.When a shackle is used in a choke hitch, the pin must be secured in the choking eye of the sling. Packing can be placed in shackle pins to make sure the hook is centered. Do not weld any material to the pin or body of the shackle. Shock loading should always be avoided.Inspection Before UseAs with all lifting equipment, shackles should be inspected before being used each day. Begin your visual inspec-tion of the shackle by checking for a clearly marked working load limit. If you can not determine the working load limit remove shackle from service. Check the body for wear, cracks, nicks and gouges especially in the bowl of the shackle and the pins. A reduction of 10% on the original or catalogue dimensions, at any point around the body or pin, is reason for retirement of the shackle. Make sure the shackle pin and body are compatible and are from the same manufacturer. NEVER use a shackle with a pin that has been replaced by a nut and bolt. Check the shackle pin thread for wear or damage. Make sure it fits correctly and snugly into the shackle body. Check that the shackle has not opened up between the ears, and the shackle is not bent or twisted. If the shackle pin is not seating properly due to this, remove shackle immediately from service.Evidence of heat damage including weld splatter or arc strike, and unauthorized welding of shackle is reason for removal from service.

100 %WLL

50 %WLL

70 %WLLVertical Line

90° fromVertical Line

45° fromVertical Line


4 Never Exceed Working Load Limit. It is the users responsibility to determine the suitability of the equipment for its intended use. Incorrect use of shackles can cause death, serious injury, or property damage.

Stock Code

Size Inches

Working Load Limit

Tons

Pin Diameter

Inside Length

Inside Width @ Pin

Weight per Piece Pounds

50LSP-G06 3/16 1/3 1/4 7/8 3/8 0.0650LSP-G08 1/4 1/2 5/16 1 1/8 15/32 0.1050LSP-G10 5/16 3/4 3/8 1 7/32 17/32 0.1950LSP-G12 3/8 1 7/16 1 7/16 21/32 0.3150LSP-G14 7/16 1-1/2 1/2 1 11/16 3/4 0.3850LSP-G16 1/2 2 5/8 1 7/8 13/16 0.7250LSP-G20 5/8 3-1/4 3/4 2 3/8 1 1/16 1.3750LSP-G24 3/4 4-3/4 7/8 2 13/16 1 1/4 2.3550LSP-G28 7/8 6-1/2 1 3 5/16 1 7/16 3.6250LSP-G32 1 8-1/2 1 1/8 3 3/4 1 11/16 5.0350LSP-G36 1 1/8 9-1/2 1 1/4 4 1/4 1 13/16 7.4150LSP-G40 1 1/4 12 1 3/8 4 11/16 2 1/32 9.550LSP-G44 1 3/8 13-1/2 1 1/2 5 1/4 2 1/4 13.5350LSP-G48 1 1/2 17 1 5/8 5 3/4 2 3/8 17.2050LSP-G56 1 3/4 25 2 7 2 25/32 27.7850LSP-G64 2 35 2 1/4 7 3/4 3 1/4 45.0050LSP-G80 2 1/2 55 2 3/4 10 1/2 4 1/8 94.0050LSP-G96 3 85 3 1/4 13 5 145.00

Procraft load rated shackles are hot dipped galvanized and meet or exceed US Fed Spec RR-C-271 Type IVA Class 2 Grade A. Working Load Limits (WLL), diameter and traceability code are forged on all Procraft load rated shackles as per ASME Standard B30.9. Load rated shackles are available as an Anchor (Bow) or Chain (Dee) type shackle, and are available with either a Screw Pin or Bolt Type (Safety) with nut and cotter pin. Look for the ‘Blue Pin’ which identifies Procraft’s quality and reliability.

Manufacturer Trace Code

Manufacturer

Size

Capacity (WLL)

Procraft Screw Pin Load Rated Anchor ShackleLoad Rated Screw Pin Anchor (SPA) Shackles are hot dipped galvanized and meet or exceeds US Fed Spec RR-C-271 Type IVA Class 2 Grade A. The screw pin is the most common type of shackle due to its ease of installa-tion, DO NOT use screw pin shackles or fit pins in contact with moving parts if the pin can roll and unscrew.


5

Stock Code

Size Inches

Working Load Limit

Tons

Pin Diameter

Inside Length

Inside Width @ Pin


50LSA-G16 1/2 2 5/8 1 7/8 13/16 0.7950LSA-G20 5/8 3-1/4 3/4 2 3/8 1 1/16 1.6850LSA-G24 3/4 4-3/4 7/8 2 13/16 1 1/4 2.7250LSA-G28 7/8 6-1/2 1 3 5/16 1 7/16 3.9550LSA-G32 1 8-1/2 1 1/8 3 3/4 1 11/16 5.6650LSA-G36 1 1/8 9-1/2 1 1/4 4 1/4 1 13/16 8.2750LSA-G40 1 1/4 12 1 3/8 4 11/16 2 1/32 11.7150LSA-G44 1 3/8 13-1/2 1 1/2 5 1/4 2 1/4 15.8350LSA-G48 1 1/2 17 1 5/8 5 3/4 2 3/8 20.8050LSA-G56 1 3/4 25 2 7 2 25/32 33.9150LSA-G64 2 35 2 1/4 7 3/4 3 1/4 55.2550LSA-G80 2 1/2 55 2 3/4 10 1/2 4 3/16 98.2550LSA-G96 3 85 3 1/4 12 3/4 5 154.00

Stock Code

Size Inches

Working Load Limit

Tons

Pin Diameter

Inside Length

Inside Width @ Pin


51LSP-G08 1/4 1/2 5/16 7/8 15/32 0.1151LSP-G10 5/16 3/4 3/8 1 1/32 17/32 0.1751LSP-G12 3/8 1 7/16 1 1/4 21/32 0.2851LSP-G14 7/16 1-1/2 1/2 1 7/16 3/4 0.4351LSP-G16 1/2 2 5/8 1 5/8 13/16 0.6051LSP-G20 5/8 3-1/4 3/4 2 1 1/16 1.2551LSP-G24 3/4 4-3/4 7/8 2 3/8 1 1/4 2.6351LSP-G28 7/8 6-1/2 1 2 13/16 1 7/16 3.1651LSP-G32 1 8-1/2 1 1/8 3 3/16 1 11/16 4.7551LSP-G36 1 1/8 9-1/2 1 1/4 3 37/64 1 13/16 6.7551LSP-G40 1 1/4 12 1 3/8 3 15/16 2 1/32 9.0651LSP-G44 1 3/8 13-1/2 1 1/2 4 3/8 2 1/4 11.63

Never Exceed Working Load Limit. It is the users responsibility to determine the suitability of the equipment for its intended use. Incorrect use of shackles can cause death, serious injury, or property damage.

Procraft Screw Pin Chain ShackleLoad Rated Screw Pin Chain (SPC) Shackles are hot dipped galvanized and meet or exceeds US Fed Spec RR-C-271 Type IVA Class 2 Grade A. The screw pin is the most common type of shackle due to its ease of installation, DO NOT use screw pin shackles or fit pins in contact with moving parts if the pin can roll and unscrew.

Procraft Bolt Type (Safety) Anchor ShackleLoad Rated Screw Pin Anchor (SBA) Shackles are hot dipped galvanized and meet or exceeds US Fed Spec RR-C-271 Type IVA Class 2 Grade A. Bolt type shackles are perfect for permanent or semi-permanent installations.


6 This product is not designed for load carrying purposes. Do not use in load carrying, overhead lifting or any load bearing application where disengagement could result in death, serious injury or property damage.

Stock Code

Size Inches

Grade of Steel

Inside Length

Inside Width @ Pin


50SP-G08 1/4 C-1015 1 1/8 1/2 0.0950SP-G10 5/16 C-1015 1 7/32 17/32 0.1150SP-G12 3/8 C-1015 1 7/16 21/32 0.2750SP-G14 7/16 C-1015 1 11/16 23/32 0.4250SP-G16 1/2 C-1015 1 7/8 13/16 0.4450SP-G20 5/8 C-1015 2 3/8 1 1/16 1.3250SP-G24 3/4 C-1015 2 13/16 1 1/4 1.9250SP-G28 7/8 C-1015 3 5/16 1 7/16 3.0850SP-G32 1 C-1015 3 3/4 1 11/16 4.40

Stock Code

Size Inches


51TRL-S12 3/8 0.2651TRL-S16 1/2 0.49

Stock Code

Size Inches

Grade of Steel

Inside Length

Inside Width @ Pin


51SP-G08 1/4 C-1015 7/8 1/2 0.0951SP-G10 5/16 C-1015 1 17/32 0.1151SP-G12 3/8 C-1015 1 3/16 21/32 0.2751SP-G14 7/16 C-1015 1 27/32 23/32 0.4251SP-G16 1/2 C-1015 1 5/8 13/16 0.4451SP-G20 5/8 C-1015 2 1 1/16 1.3251SP-G24 3/4 C-1015 2 3/8 1 1/4 1.90

Procraft Non-Rated Anchor ShackleNon-Rated Shackles are generally used in conjunction with chain, wire rope and cordage in non-load bearing applications such as guying, anchoring and mooring. These shackles are non-load rated and SHOULD NOT be used in any load bearing or lifting applications!

Procraft Non-Rated Trawl ShackleTrawl Shackles are used extensively in the fishing industry. The square head is used for ease of installation and the thin head avoids getting caught on netting and gear. These shackles are non-load rated and SHOULD NOT be used in any load bearing or lifting applications!

Procraft Non-Rated Chain ShackleNon-Rated Shackles are generally used in conjunction with chain, wire rope and cordage in non-load bearing applications such as guying, anchoring and mooring. These shackles are non-load rated and SHOULD NOT be used in any load bearing or lifting applications!


7

Stock Code

Size Inches

Grade of Stainless

Inside Length

Inside Width @ Pin


50LSP-SS08 1/4 Type 316 1 1/16 1/2 0.1050LSP-SS10 5/16 Type 316 1 5/16 9/16 0.1950LSP-SS12 3/8 Type 316 1 7/16 5/8 0.3150LSP-SS16 1/2 Type 316 1 13/16 7/8 0.7250LSP-SS20 5/8 Type 316 2 5/16 1 1/16 1.3750LSP-SS24 3/4 Type 316 2 7/8 1 3/16 2.3550LSP-SS32 1 Type 316 3 3/4 1 5/8 5.00

Stock Code

Size Inches

Grade of Stainless

Inside Length

Inside Width @ Pin


51LSP-SS08 1/4 Type 316 7/8 15/32 0.1051LSP-SS10 5/16 Type 316 1 1/2 0.1651LSP-SS12 3/8 Type 316 1 1/4 5/8 0.2451LSP-SS16 1/2 Type 316 1 5/8 13/16 0.4051LSP-SS20 5/8 Type 316 1 15/16 1 1/16 1.0051LSP-SS24 3/4 Type 316 2 5/16 1 3/16 2.0551LSP-SS32 1 Type 316 3 1/4 1 9/16 4.12

This product is not designed for load carrying purposes. Do not use in load carrying, overhead lifting or load bearing application where disengagement could result in death, serious injury or property damage.

Procraft Non-Rated Stainless Steel Anchor ShackleStainless Steel Shackles are manufactured from grade 316 stainless steel. They are generally used in corrosive environments in conjunction with chain, wire rope and cordage as part of non-load bearing applications such as railings, mooring and anchoring. These shackles are non-load rated and SHOULD NOT be used in any load bear-ing or lifting applications!

Procraft Non-Rated Stainless Steel Chain ShackleStainless Steel Shackles are manufactured from grade 316 stainless steel. They are generally used in corrosive environments in conjunction with chain, wire rope and cordage as part of non-load bearing applications such as railings, mooring and anchoring. These shackles are non-load rated and SHOULD NOT be used in any load bear-ing or lifting applications!


8 Strictly adhere to manufacturers instructions on installation. Failure to understand and install wire rope clips correctly could result in death, serious injury or property damage.

Stock Code

Size Inches

Minimum Clips per

Eye

Amount of Rope to Turn Back Inches

Torque in Foot-Pounds


22SS-04 1/8 2 3 1/4 4.5 0.0622SS-06 3/16 2 3 3/4 7.5 0.0922SS-08 1/4 2 4 3/4 15 0.1822SS-10 5/16 2 5 1/4 30 0.3122SS-12 3/8 2 6 1/2 45 0.4322SS-16 1/2 3 11 1/2 65 0.7622SS-20 5/8 3 12 95 1.0122SS-24 3/4 4 18 130 1.52

Procraft Drop Forged Stainless Steel Wire Rope ClipsStainless Steel Drop Forged Clips are manufactured from grade 304 Stainless material. They are generally used in corrosive or harsh environments, and are easily installed to form eyes in wire rope.

DROP FORGED WIRE ROPE CLIPS are useful for field installation of eyes in wire rope. With correct instal-lation using a torque wrench, this type of termination can create 80% efficiency when used with 6 x 19 / 6 x 36 class wire rope.It is important that installation instructions are followed carefully and the table below outlining minimum clips to be used and torque to be applied is strictly adhered to.Installation1. Turn back specified amount of rope (see table) from thimble or loop. Apply first clip one base width from dead end of rope. Apply U-bolt over dead end of wire rope - live end rests in saddle (Never saddle a dead horse!). Tighten nuts evenly, alternating from one nut to the other until reaching the recom-mended torque.2. Apply the second clip as near the loop or thimble as possible. Tighten nuts evenly, alternating until reaching the recommended torque. When more than two clips are required, apply the second clip as near the loop or thimble as possible, turn nuts on second clip firmly, but do not tighten. Proceed to Step 3. 3. When three or more clips are required, space additional clips between first two - take up rope slack - tighten nuts on all clips, alternating from one nut to the other until reaching the recommended torque.4. Apply an initial load equal to or greater than the loads expected in use. Inspect for proper spacing and re-tight-en the nuts to the recommended torque.Maintenance & Use Wire Rope clips should be inspected frequently to make sure there is no wire rope slippage, indication of wire rope damage, improperly installed clips, loose or improperly tightened nuts and any signs of fatigue, wear or corrosion on the clip. Periodical re-tightening of nuts to torque values may be required. Wire rope clips should not come into contact with any loads or obstruction during lifts or when installed in static environments. Shock loading should be avoided at all times and using wire rope clips for lifting slings is prohibited. When joining two wire ropes with wire rope clips they must be installed as per diagram opposite. NEVER use wire rope clips with plastic coated wire rope.


9

Stock Code

Size Inches

Minimum Clips Per

Eye

Amount of Rope to Turn Back Inches

Torque in Foot-Pounds


22FG-04 1/8 2 3 1/4 4.5 0.0622FG-06 3/16 2 3 3/4 7.5 0.1022FG-08 1/4 2 4 3/4 15 0.1922FG-10 5/16 2 5 1/4 30 0.2822FG-12 3/8 2 6 1/2 45 0.4822FG-16 1/2 3 11 1/2 65 0.8022FG-18 9/16 3 12 95 1.0922FG-20 5/8 3 12 95 1.1022FG-24 3/4 4 18 130 1.4222FG-28 7/8 4 19 225 2.1222FG-32 1 5 26 225 2.5222FG-36 1 1/8 6 34 225 2.8322FG-40 1 1/4 7 44 360 4.3822FG-44 1 3/8 7 44 360 4.4222FG-48 1 1/2 8 54 360 5.4422FG-56 1 3/4 8 61 590 9.3422FG-64 2 8 71 750 13.00

Malleable Clips are not designed for load carrying purposes. Do not use in load carrying, overhead lifting or any application where disengagement could result in death, serious injury or property damage.

Stock Code Size Inches Weight per Piece Pounds22MG-02 1/16 0.0322MG-04 1/8 0.0422MG-06 3/16 0.0322MG-08 1/4 0.1222MG-10 5/16 0.1422MG-12 3/8 0.2122MG-14 7/16 0.2722MG-16 1/2 0.3522MG-20 5/8 0.5822MG-24 3/4 0.8422MG-28 7/8 1.2422MG-32 1 1.50

Procraft Drop Forged Wire Rope ClipsDrop forged wire rope clips are used for heavy duty applications or where loading conditions are severe. Preci-sion manufactured and galvanized to meet Federal Specifications FF-C-450, Type 1, Class 1. The base is drop forged and hot dipped galvanized for the toughest conditions. Please see installation instructions on page 8.

Procraft Malleable Wire Rope ClipsMalleable Clips are used in very light rigging applications where strength is not required. DO NOT use these clips for lifting, hoisting or any critical load carrying applications.


10 This product is not load rated but is designed to protect rope from damage. Remove from service any thimbles that are damaged, cracked, worn or elongated.

THIMBLES are designed and manufactured to protect wire rope from wear and damage, and preserve the shape of the eye when using shackles and hooks. Always ensure that you have the correct thimble for the size of rope being used, for any intermediate size the next size must be used. Thimbles are not load rated and only serve to protect the rope. Always inspect thimbles for abuse, damage, cracks and deformation (stretch) before use. Thim-bles can be used for wire or synthetic rope.

Stock Code

Size Inches

Maximum Inside Diameter Inches


76HD-G08 1/4 11/16 0.0776HD-G10 5/16 13/16 0.1476HD-G12 3/8 15/16 0.2576HD-G14 7/16 1 0.3576HD-G16 1/2 1 1/8 0.5176HD-G20 5/8 1 3/8 0.7676HD-G24 3/4 1 5/8 1.4776HD-G28 7/8 1 7/8 1.7876HD-G32 1 2 1/2 3.00

76HD-G3640 1 1/8 to 1 1/4 2 3/4 3.8076HD-G4044 1 1/4 to 1 3/8 3 1/2 8.6076HD-G4448 1 3/8 to 1 1/2 3 1/2 12.9476HD-G56 1 3/4 4 1/2 17.7576HD-G64 2 6 27.75

Stock Code

Size Inches



76SS-HD08 1/4 11/16 0.0876SS-HD10 5/16 13/16 0.1476SS-HD12 3/8 15/16 0.2676SS-HD16 1/2 1 1/8 0.5376SS-HD20 5/8 1 3/8 0.7076SS-HD24 3/4 1 5/8 1.2576SS-HD28 7/8 1 7/8 1.5076SS-HD32 1 2 1/2 2.50

Procraft Galvanized Heavy Duty ThimblesHeavy duty thimbles should be used for any lifting or load bearing applications. These heavy duty thimbles are galvanized and ideal for use in wire rope slings, winch lines and other wire or synthetic rope terminations.

Procraft Stainless Steel Heavy Duty ThimblesHeavy duty thimbles should be used for any lifting or load bearing applications. These heavy duty thimbles are stainless steel and ideal for use in wire rope slings, winch lines and other wire or synthetic rope terminations. The Stainless Steel finish make them ideal for many marine applications.


11This product is not load rated and not suitable for any load bearing or lifting applications. Thimbles are designed to protect rope from damage.

Stock Code

Size Inches



76ST-G04 1/8 11/16 0.0476ST-G06 3/16 11/16 0.0476ST-G08 1/4 11/16 0.0476ST-G10 5/16 13/16 0.0576ST-G12 3/8 15/16 0.0876ST-G16 1/2 1 0.1476ST-G20 5/8 1 1/4 0.3676ST-G24 3/4 1 1/2 0.5076ST-G28 7/8 1 3/4 0.9076ST-G32 1 2 3/8 1.04

Stock Code

Size Inches



76SS-02 3/64,1/16, 5/64 3/8 0.0176SS-04 3/32,1/8, 7/64 3/8 0.0276SS-05 5/32 7/16 0.0376SS-06 3/16 1/2 0.0376SS-08 1/4 3/4 0.0476SS-10 5/16 15/16 0.0676SS-12 3/8 1 0.08

Stock Code

Size Inches



76TB-16 3/8 0.87 0.5576TB-20 1/2 1.05 0.9376TB-24 5/8 1.25 1.3376TB-28 3/4 1.40 1.7776TB-32 7/8 1.75 3.0176TB-36 1 1.80 4.42

Procraft Zinc Plated Light Duty ThimblesLight duty thimbles are used in light rigging applications where the thimble is not exposed to heavy loads. Thesethimbles will stretch and deform if subject to heavy loading.

Procraft Stainless Steel Light Duty ThimblesLight duty thimbles are used in light rigging applications where the thimble is not exposed to heavy loads. Thesethimbles will stretch and deform if subject to heavy loading. The Stainless Steel finish make them ideal for many marine applications.

Procraft Steel Tube ThimblesTube thimbles are designed to protect the rope at the bearing point and the sides from chaffing. They are com-monly used in the fishing industry and as end fittings on utility winch lines.


12Aluminium sleeves are not recommended for any critical overhead lifting applications. To determine the holding strength of any assem-bly a proof load test and destruction testing is recommended. Sleeves crimped over plastic jackets on wire rope will not hold to published breaking strengths. Unsafe use of this product could result in disengagement and the potential of death, serious injury or property damage.

WIRE ROPE SLEEVES are used in conjunction with swaging tools and ma-chines to form eyes or stops onto wire rope. When field installation is required for smaller diameter ropes, a wire rope crimping tool can be used on hand swage sleeves. To ensure a safe and correct swage the following needs to be reviewed:1 - Always ensure that you have the correct size sleeve for the wire rope diameter that you are using. 2 - The correct tool and groove on the tool is used for your wire rope diameter.3 - You have the correct number of presses on the sleeve for your diameter rope.4 - Check the sleeve for the correct finish diameter (many tools have a gauge to assist with this)5 - When crimping wire rope to form an eye it is important to allow a tail to protrude from the end of the sleeve. This tails should be at least 1.5 times the rope diameter before crimping. If swaging a Thimble eye there should be a small space between the thimble and sleeve to allow thimble some self alignment. To crimp the sleeve as follows:Step 1 - Crimp centre of the Sleeve first.Step 2 - Crimp the end closest to the eye next. Step 3 - Crimp the end closest to the tail.Aluminum sleeves are not to be used for dynamic loads.

Wire Rope

Oval Sleeve

2nd Stage3rd Stage1st Stage

1.5 Times Wire Rope Diameter

Oval Sleeve

Wire Rope

Procraft Aluminum Duplex Sleeves (Hourglass)Aluminum hourglass sleeves are an economical way to install eyes on site with the use of a swaging tool. To determine actual holding strength of the pressed assembly a proof load test is recommended.

Stock Code

Size Inches


56AL-015 3/64 0.00156AL-02 1/16 0.00156AL-03 3/32 0.00356AL-04 1/8 0.00656AL-05 5/32 0.00856AL-06 3/16 0.01656AL-08 1/4 0.02656AL-10 5/16 0.046

56AL-12HG 3/8 0.06256AL-14HG 7/16 0.11856AL-16HG 1/2 0.176


13

Stock Code

Size Inches


56AL-10 5/16 0.04356AL-12HG 3/8 0.05356AL-14HG 7/16 0.11056AL-16HG 1/2 0.165

56AL-18 9/16 0.22056AL-20 5/8 0.32056AL-24 3/4 0.52056AL-28 7/8 0.67056AL-32 1 1.25056AL-36 1 1/8 1.72056AL-40 1 1 /4 2.140

Stock Code

Size Inches


56BS-02 1/16 0.00156BS-03 3/32 0.00156BS-04 1/8 0.00356BS-05 5/32 0.00456BS-06 3/16 0.00456BS-08 1/4 0.02156BS-10 5/16 0.021

Procraft Aluminum Oval Swage SleevesAluminum oval swage sleeves are for installing eyes onto wire ropes for non critical applications. These sleeves are used in hydraulic presses with special dies to swage the sleeve. To determine actual holding strength of the pressed assembly a proof load test is recommended.

Procraft Aluminum Button StopsAluminum button stops are mainly used to install stop ends on wire ropes for quick installation into drums and fittings. Stop sleeves will not hold to the nominal published break strength of any cable, if installed correctly the stop will hold to 1/3 the nominal strength of the cable.

Aluminium sleeves and stops are not recommended for any critical overhead lifting applications. To determine the holding strength of any assembly a proof load test and destruction testing is recommended. Sleeves and stops crimped over plastic jackets on wire rope will not hold to published breaking strengths. Unsafe use of this product could result in disengagement and the potential of death or serious injury.


14

Procraft Copper Duplex Sleeves (Hourglass)Copper hourglass sleeves are an economical way to install eyes on site with the use of a swaging tool. To deter-mine actual holding strength of the pressed assembly a proof load test is recommended.

Stock Code

Size Inches


56CP-015 3/64 0.00256CP-02 1/16 0.00356CP-03 3/32 0.00956CP-04 1/8 0.01856CP-05 5/32 0.02756CP-06 3/16 0.05556CP-08 1/4 0.07956CP-10 5/16 0.14156CP-12 3/8 0.19656CP-14 7/16 0.37256CP-16 1/2 0.595

Procraft Copper Button StopsCopper button stops are mainly used to install stop ends on wire ropes for quick installation into drums and fit-tings. Stop sleeves will not hold to the nominal published break strength of any cable, if installed correctly the stop will hold to 1/3 the nominal strength of the cable.

Stock Code

Size Inches


56BS-02 1/16 0.00156BS-03 3/32 0.00256BS-04 1/8 0.00756BS-05 5/32 0.01456BS-06 3/16 0.01456BS-08 1/4 0.07156BS-10 5/16 0.064

Copper sleeves are not recommended for any critical overhead lifting applications. To determine the holding strength of any assembly a proof load test and destruction testing is recommended. Sleeves crimped over plastic jackets on wire rope will not hold to published breaking strengths. Unsafe use of this product could result in disengagement and the potential of death, serious injury or property damage.


15

Stock Code

Description & Wire Rope Diameter


30CHK-12 3/8” Midget 0.3730CHK-14 7/16” Midget 0.3530CHK-16 1/2" Midget 0.3330CHK-18 9/16" Midget 0.8030CHK-20 5/8" Midget / Dwarf 0.8030CHK-24 3/4" Bantam 1.10

Stock Code

Description Wire Rope Diameter


30CFER-L293I Micro Midget 3/8”-7/16”-1/2” 1.00

30CFER-L625I Heavy Duty Midget 3/8"-1/2"-9/16" 1.75

30CFER-L320I Light Bantam (Dwarf) 1/2"-5/8"-11/16" 3.00

Procraft Steel Machine Press Choker KnobsSteel press choker knobs are heavily used in the logging industry. They are easily inserted under logs and loads that are to be lifted or moved, and are quickly installed in choker bells to form a tight choke around loads. These fittings are designed to be installed onto cables by special dies and presses, and SHOULD NOT be installed by any other methods.

Procraft Choker Hooks (Choker Bells)Procraft choker hooks are used in conjunction with choker knobs to form a strong choke around logs or loads which are to be moved or lifted. They are made from high quality steel to provide strength and ruggedness. Make sure that you are properly trained in the use of this product before using it with loads.

Choker Knobs and Hooks ARE NOT intended for use in overhead lifting operations except for some log harvesting systems where adequate protection and precautions are taken. Unsafe use of this product could result in disengagement and the potential of death, serious injury or property damage.


16

ALLOY HOOKS are used extensively for overhead lifting in a variety of applications to connect loads to slings and other hardware.Rigging PracticesAlways use alloy hooks for overhead lifting. Know what hook to use, and how to use it, and match or exceed the WLL of the slings that you are to use. When rigging a load on hooks make sure the load is centered in the bowl of the hook. If using two slings the angle from the vertical to the outermost leg should not exceed 45 degrees.NEVER tip load, point load, side load or back load a hook. Always check to ensure that the safety latch has fully closed correctly before lifting and ensure the safety latch is NOT sup-porting any load.Always use a swivel hook with a proper bearing if you intend to rotate a hook when fully loaded. NEVER swivel or turn a standard swivel hook with bushing or bearing washer when fully loaded (as per hooks found in this catalogue). Inspection before use is extremely important.InspectionAlways check that the WLL is still visible.Check that the safety latch is installed and functioning correctly.Hooks should be inspected carefully for cracks, distortion, corrosion or heat strike / welding marks.Inspect for any signs of excessive wear. Any wear exceeding 10% should be removed from service immediately.Check the throat opening. If throat opening exceeds 15% of the original dimension, it must be removed from service. A good practice is to remove any hook that shows sign of throat opening.Check hook for side loading. If the hook tip and eye do not line up and the hook is bent or twisted remove from service.Never use a hook that has been repaired or altered by heating, welding, burning or bending.Inspect carefully the neck (shank) of a swivel hook for signs of side loading, wear or deterioration.

Check for Opening Up.

Check for Wear & Deformation

Check for Wear & Cracks

Check for Cracks & Twisting

45° 45°

Stock Code

Working Load Limit Tons

Opening Inches


36EYE-A010 1 0.90 0.6136EYE-A015 1 1/2 0.93 0.8236EYE-A020 2 1.00 1.4436EYE-A030 3 1.13 1.9436EYE-A050 5 1.44 4.3036EYE-A070 7 1.75 7.7536EYE-A110 11 2.29 15.00

Inspect all alloy hooks prior to use. NEVER point load or side load a lifting hook. NEVER exceed the working load limit. Unsafe or im-proper use could result in disengagement and the potential of death, serious injury or property damage.

Procraft Alloy Eye Hoist HooksAlloy eye hooks come complete with a safety latch, and are marked with the working load limit, manufacturer and traceability code as per ASME standards. They have a built in safety factor of 5:1 which make them ideal for wire rope, synthetic rope and chain assemblies.


17

Stock Code

Working Load Limit Tons

Opening Inches


36SW-A010 1 0.90 0.7736SW-A015 1 1/2 0.93 1.2736SW-A020 2 1.00 2.2836SW-A030 3 1.13 2.6036SW-A050 5 1.47 4.8136SW-A070 7 1.75 10.4036SW-A110 11 2.29 16.42

Stock Code

Hook Capacity Tons

Overall Length

Width @ Opening


36XLK-A010 1 1.48 0.41 0.0236XLK-A015 1 1/2 1.84 0.41 0.0236XLK-A020 2 1.84 0.49 0.0336XLK-A030 3 2.02 0.49 0.0336XLK-A050 5 2.41 0.63 0.0636XLK-A070 7 2.99 0.71 0.1136XLK-A110 11 3.68 0.79 0.17

Procraft Alloy Swivel Eye Hoist HooksSwivel alloy eye hooks come complete with a safety latch, and are marked with the working load limit, manu-facturer and traceability code as per ASME standards. They have a built in safety factor of 5:1 which make them ideal for wire rope, synthetic rope and chain assemblies. These hooks are designed for load positioning and there-fore will not swivel under load. NEVER swivel this type of hook when fully loaded.

Procraft Stainless Steel Latch KitsThese latch kits are a suitable replacement for when your factory installed latches have been damaged or are beyond repair. They are manufactured from Stainless Steel for increased service life.

Inspect all alloy hooks prior to use. NEVER point load or side load a lifting hook. NEVER exceed the working load limit. Safety latches are not designed to be loaded. Unsafe or improper use could result in disengagement and the potential of death, serious injury or property dam-age.

Procraft Alloy Swivel Trigger HooksSwivel positive locking trigger hooks are marked with manufacturer and traceability code as per ASME stand-ards. They have a built in safety factor of 4:1 which make them ideal for chain. These hooks are designed for load positioning and therefore will not swivel under load. NEVER swivel this type of hook when fully loaded.

Stock Code

Chain Size

Working Load Limit Pounds


71HSA-SE08 1/4" - 5/16" 3,500 2.6571HSA-SE12 3/8" 7,100 4.9671HSA-SE16 1/2" 12,000 9.1171HSA-SE20 5/8" 18,100 16.87


18

Stock Code

Diameter Inches



40SLG-12 3/8" 1,800 0.2340SLG-16 1/2" 2,900 0.5140SLG-20 5/8" 4,200 1.0640SLG-24 3/4" 6,000 1.9540SLG-32 1" 10,800 4.35

Stock Code

Diameter Inches



40RNG-2840 7/8" x 4" 7,200 2.7240RNG-3240 1" x 4" 10,800 3.47

Ensure the Working Load Limit of any Links or Rings is greater than the rated capacity of the wire rope or chain bridle. NEVER exceed the working load limit. Unsafe or improper use could result in disengagement and the potential of death, serious injury or property damage.

Stock Code


Weight per Pair Pounds

36BAR-I 2,000 (Pair) 3.56

Procraft Galvanized Barrel HooksBarrel hooks can be used with wire rope, web, rope or chain slings. Ensure that the barrel to be lifted is in excel-lent condition and that the barrel hooks are secured safely on barrel before lifting. Use extreme caution once load is lifted from the ground. These hooks have a 4:1 factor of safety. DO NOT exceed Working Load Limits.

PEAR LINKS AND ROUND RINGS are designed for use on wire rope, synthetic rope and web assemblies. They are carbon steel weldless links that are drop forged to create a seamless one piece unit. They are great for sling assemblies with multiple legs, but may not be optimal for some crane hook designs. Before use, links and rings should be inspected for signs of wear, bending, distortion (elongation or collapse), cracks, corrosion damage, nicks and gouges. Any links or rings which have 10% loss of material diameter from original diameter should be discarded. If any gouges or nicks have penetrated to 10% of the original material diameter, the product must be removed from service.Links or rings which are bent more than 10 degrees in the plane, or which are visibly distorted or twisted should also be discarded.

Procraft Carbon Steel Round LinksSteel round rings are generally used as part of multi leg wire or synthetic rope bridles. They have a 5:1 factor of safety and marked on the ring working load limit, manufacturer and traceability code. DO NOT exceed Working Load Limits.

Procraft Galvanized Carbon Steel Pear LinksPear shaped sling links are generally used as part of multi leg wire rope, synthetic rope or chain bridles. They are a one piece carbon steel forged product, hot dipped galvanized, with the Working Load Limit, manufacturer and traceability code marked on the link. They have a 6:1 factor of safety. DO NOT exceed Working Load Limits.


19

Stock Code

Diameter Inches



68JE-08 1/4 850 0.2168JE-10 5/16 1,250 0.3468JE-12 3/8 2,250 0.6668JE-16 1/2 3,600 1.3468JE-20 5/8 5,200 2.3068JE-24 3/4 7,200 3.5068JE-28 7/8 10,000 5.8768JE-32 1 12,500 9.85

SWIVELS are used in conjunction with chain, wire or synthetic rope and slings. They are designed to be used for positioning hooks or slings onto the correct plane before lifting any product. They SHOULD NOT be used for rotating product while under load. They are fully forged and hot dipped galvanized product with forged markings for easy indentification and traceability. Two different types are available, a Jaw End Swivel which has an eye one end and a jaw fitting for easy attachment and a Regular Swivel which has an enclosed eye at each end. They have a 5:1 factor of safety for lifting, which the Working Load Limit should NEVER be exceeded. Swivels should be inspected regularly for any signs of damage, distortion or wear. Careful inspection should take place where the two sections of the swivel meet, look for any signs of fatigue, corrosion or excessive wear. A 10% reduction in material diameter is classified as excessive wear, and should be removed from service.

Procraft Galvanized Carbon Steel Jaw End SwivelJaw & Eye or Jaw End Swivels can be used in conjunction with wire, chain or synthetic slings. One end has an enclosed eye while the other end has a jaw fitting for quick installation onto ropes and assemblies. They are NOT designed to rotate under load and are for load positioning only.

Procraft Galvanized Carbon Steel Regular SwivelEye & Eye or Regular Swivels can be used in conjunction with wire, chain or synthetic slings. Each end has an enclosed eye for installation onto ropes and assemblies with connectors. They are NOT designed to rotate under load and are for load positioning only.

Stock Code

Diameter Inches



68REG-08 1/4 850 0.2168REG-10 5/16 1,250 0.3968REG-12 3/8 2,250 0.7168REG-16 1/2 3,600 1.0068REG-20 5/8 5,200 2.0068REG-24 3/4 7,200 4.0068REG-28 7/8 10,000 6.2568REG-32 1 12,500 8.95

Swivels are designed for load positioning, DO NOT force rotation of swivel when under load. Swivels must be inspected for wear, distortion and damage before using for any lifts. DO NOT exceed Working Load Limits.


20 To avoid injury or property damage ensure that instructions are followed carefully and eyebolts are always inspected before each use. If unsure on instructions please check with Pro Sling & Safety for further details.

EYEBOLTS are commonly attached to a load to provide an attachment point for slings and rigging. They are generally manufactured from forged carbon or alloy steel.Eyebolt TypesEyebolts come in many varying configurations. You can get them with shoulder nut, regular (shoulder less), ma-chinery, swivel hoist rings and eyenuts. Shoulder eyebolts are the most practical eyebolt to use as they provide a support to the eyebolt shaft and allows angular lifting with a reduction in capacity. Shoulderless eyebolts are used for in-line lifting only. Swivel hoist rings are suitable for angular type lifting particularly angles exceeding 45 degrees (swivel hoist rings are available in a range of products, please check with Pro Sling & Safety for further details). Eyenuts are drilled and tapped to accept threaded rated rod.Instructions for Safe Use1. Ensure that you have the correct eyebolt for the lift. Always use shoulder eyebolts for all applications, except where it is not possible due to the configu-ration of the load. Shoulderless eyebolts are fine for vertical loading but can bend and fail under angular loading. Shoulder eyebolts loose some capacity when loaded on an angle. Use swivel hoist rings where ever possible on angu-lar lifting especially angles at or less than 45 degrees.2. Ensure shoulder seats snugly on the surface which they bear. Make sure the eyebolt is screwed down completely and the nut is tightened securely against the load. Spacers may be used, if necessary, to ensure proper seating of the eyebolt. A washer should not be less in diameter than the diameter of the shoulder, and the thickness of the steel washer or spacer must not exceed one thread pitch.3. An eyebolt must be installed into a tapped hole with a minimum depth of two times the shank diameter.4. When using lifting slings having two or more legs, make sure the load on each leg is calculated based on the angular loading. Use an eyebolt with a shoulder or swivel hoist ring with the correct WLL suited to the angle being lifted. Reductions for Angular Lifting with Eyebolts:True Vertical - Full catalogue Working Load Limit75° - 55% of full catalogue Working Load limit65° - 35% of full catalogue Working Load limit45° - 25% of full catalogue Working Load limit DO NOT USE less than 45°5. DO NOT reeve a sling through a pair of bolts, attach a separate sling to each eyebolt. NEVER insert the point of a hook in an eyebolt, use a shackle instead.6. DO NOT use wrenches, bars etc to tighten standard eyebolts. Hand tightening is recommenced.7. DO NOT use a single eyebolt to lift a load that can rotate.8. DO NOT exceed the rated capacity. DO NOT shock load eyebolts, gradually increase lifting with a steady and even lift.9. Always inspect eyebolts before use.Inspection Before UseClean eyebolt and inspect for any signs of defects or wear. Check eyebolt for signs of deformation, distortion, cracks, loss of material, bent shank and that the centre line of the thread is aligned with the centre line of the eye. Always inspect carefully the thread ensuring that there is no damage or wear to the threaded section. Remove and destroy any eyebolts showingsigns of damage or abuse as outlined above. NEVER machine, cut, grind or weld any eyebolts. DESTROY any eyebolts showing signs of alteration.

Ensure thread centre is aligned with centre of the eye.

Check for Cracking

Check inside ofeye for wear

Check fordeformation

Check threads fordamage and wear

Applying load in thisdirection will result in a benteyebolt and an unsafe lift.

Load

Result

Result

If eyebolt is not seated snugly against the shoulder, the result will be a damged or unsafe eyebolt.

Load

0°

45°65°75°

Do not use less than 45°

TrueVertical


21

Stock Code

Diameter x Thread Length

Working Load Limit Pounds @ 90 Degrees

Eye Diameter


28BSH-01 1/4 X 2 650 0.50 0.0628BSH-02 1/4 X 4 650 0.50 0.0928BSH-03 5/16 X 2 1/4 1,200 0.62 0.1128BSH-04 5/16 X 4 1/4 1,200 0.62 0.1528BSH-05 3/8 X 2 1/2 1,550 0.75 0.1928BSH-06 3/8 X 4 1/2 1,550 0.75 0.25

28BSH-06X 3/8 x 6 1,550 0.75 0.3128BSH-07 1/2 X 3 1/4 2,600 1.00 0.4128BSH-08 1/2 X 6 2,600 1.00 0.59

28BSH-08X 1/2 x 8 2,600 1.00 0.6328BSH-09 5/8 X 4 5,200 1.25 0.8328BSH-10 5/8 X 6 5,200 1.25 1.00

28BSH-10X 5/8 x 8 5,200 1.25 1.1728BSH-11 3/4 X 4 1/2 7,200 1.50 1.5028BSH-12 3/4 X 6 7,200 1.50 1.68

28BSH-12X 3/4 x 8 7,200 1.50 1.9228BSH-14 1 x 6 13,300 2.00 3.6728BSH-15 1 x 9 13,300 2.00 4.22

28BSH-15X 1 x 12 13,300 2.00 4.7728BSH-16 1 1/4 x 8 21,000 2.50 6.50

Procraft Galvanized Shoulder Nut EyeboltsShoulder nut eyebolts are carbon steel and hot dipped galvanized, which makes them ideal for marine and out-door environments. They are available with long shank lengths suitable for inserting through thicker material. The shoulder gives support to the eyebolt and allows for limited angular loading.

To avoid injury or property damage ensure that instructions are followed carefully and eyebolts are always inspected before each use. If unsure on instructions please check with Pro Sling & Safety for further details.


22

Stock Code

Number & Thread Diam-

eter


Inside Width


28NUT-08 # 1 - 1/4" 520 0.75 0.0928NUT-10 # 1A - 5/16" 700 0.75 0.0928NUT-12 # 2 - 3/8" 1,250 1.00 0.1828NUT-16 # 3A - 1/2" 2,250 1.25 0.2928NUT-20 # 4 - 5/8" 3,600 1.50 0.5828NUT-24 # 5 - 3/4" 5,200 1.75 1.0028NUT-28 # 6 - 7/8" 7,200 2.00 1.7028NUT-32 # 7 - 1" 10,000 2.15 2.7528NUT-40 # 8 - 1 1/4" 15,200 2.50 3.85

To avoid injury or property damage ensure that instructions are followed carefully and eyebolts are always inspected before each use. Ensure any threaded road has the load rated capacity of the eye nut, failure to do so could result in failure and serious injury or death.

Stock Code



Eye Diameter


28BTH-08 1/4 X 1 500 0.88 0.0428BTH-10 5/16 X 1 1/8 900 1.12 0.0628BTH-12 3/8 X 1 1/4 1,300 1.38 0.1328BTH-16 1/2 X 1 1/2 2,400 1.75 0.2528BTH-20 5/8 X 1 3/4 4,000 2.25 0.5028BTH-24 3/4 X 2 5,000 2.75 0.8828BTH-28 7/8 X 2 1/4 7,000 3.25 1.5028BTH-32 1 X 2 1/2 9,000 3.75 2.18

Procraft Carbon Steel Machinery eyeboltsMachinery eyebolts are suitable for equipment lifts. It has a short thread perfect for installing in electric motors, gearboxes, and other types of equipment with pre-sunk holes. The shoulder gives support to the eyebolt and al-lows for limited angular loading.

Procraft Carbon Steel Galvanized Eye NutsEye Nuts are hot dipped galvanized and are suitable for installing onto threaded, load rated rod. When using in lifting applications it is critical that you ensure the threaded rod to be used in conjunction with the Eye Nut has an equal or greater working load limit than the Eye Nut.


23

Stock Code


Eye Diameter


28BSC-12 3/8 X 2 1/2 1.38 0.1928BSC-16 1/2 X 3 1/4 1.75 0.3828BSC-20 5/8 X 4 2.25 0.69

Stock Code

Size Number

Eye Diameter


28PAD-1 # 1 0.37 0.0728PAD-15 # 1 1/2 0.63 0.1128PAD-2 # 2 0.75 0.2228PAD-4 # 4 1.00 0.5328PAD-5 # 5 1.25 0.82

Ensure Pad Eyes are welded and installed correctly according to Canadian & American Welding Standards. Pad Eyes should NEVER be used for any critical overhead lifting applications. DO NOT insert screw eyebolts into any rotting, decaying or damaged timber.

Stock Code

Bolt Diameter


44ZW-TMBR12 3/8 0.1844ZW-TMBR16 1/2 0.2244ZW-TMBR20 5/8 0.3244ZW-TMBR24 3/4 0.4244ZW-TMBR28 7/8 0.5544ZW-TMBR32 1 0.69

Procraft Carbon Steel Self Colour Pad EyesPad Eyes are suitable for installing onto trucks, farm machinery and marine vessels. They are easily installed by welding to steel surfaces. Ensure you follow Canadian Welding instructions and standards.

Procraft Galvanized Malleable Timber WashersTimber washers are used in dock and wood construction. The large surface area is designed to prevent the bolt heads and nuts from pulling into the timber.

Procraft Carbon Steel Screw Eyebolts (Lag Eyebolts)Screw eyebolts are hot dipped galvanized and are ideal for screwing into timbers. DO NOT use this type of eye-bolt for any critical load bearing or lifting applications.


24 To avoid injury or property damage use turnbuckles in direct tension only. NEVER side load or exceed the working load limit. Always ensure there is thread engagement of at least 1.5 times the thread diameter.

TURNBUCKLES are used to make adjustments on length for all type of rigging assemblies. They can be used for both lifting slings and as standing rigging for guy cables on towers and other engineered applications.Description & TypesTurnbuckles sizes are designated by the thread diameter on the end fitting and the length measurement inside the body. For instance a 3/8” x 6” Jaw & Jaw, is 3/8” thread diameter on the jaw fitting and 6” measurement on the inside of the body or “take up”. Turnbuckles can be supplied with several different end fittings including eyes, jaws, stub and hooks. Eye and Jaw end fittings are the most common, and hook or stub end fittings are less fre-quently used and have a rated capacity lower than Jaw and Eye fittings. Instructions for Safe Use1. Ensure the correct Turnbuckle is selected for its application or intended use. Check strength ratings match the wire rope or hardware that it is installed with.2. Place turnbuckle in line with the rigging and adjust turnbuckle so that the “slack” is taken out of the line and tension is applied to the turnbuckle. (turnbuckles are designed for loading in direct tension only).3. Ensure that there is thread engagement at either end of at least 1.5 times the thread diameter.4. When tightening a turnbuckle, do not apply more torque than you would to a bolt of equal size. 5. When turnbuckles are exposed to vibration, lock frames to end fittings. This will prevent turning and loosening of the end fittings. Use jam nuts or lock nuts, or secure end fittings with wire.6. Lubricate threads and body for extra corrosion protection.7. Ensure the threaded fittings in the turnbuckle are clear and free from any potential strike or wear damage from foreign objects.Inspection1. Inspect turnbuckles before installing on any line. Also, regular periodic inspection of permanently installed turnbuckles is required.2. Inspect end fittings for any cracks especially at the neck of the fitting. Check the end fitting for defor-mation or elongation, deformed or bent rods, and any signs of thread damage.3. Check body for deformation or bends, and any signs of thread damage or cracks in the body.4. Locknuts which are fitted are a method of locking the turnbuckle, but may not provide reliable locking under all circumstances. Locknuts should be inspected regularly for any “backing off”.5. Turnbuckles are not designed for continous adjustment while under rated load conditions. If they are used in this way careful frequent inspections of the thread should be performed as wear on the threads is expected.

Ensure �ttings are tight & secured and no bent or distorted pins.

Check for cracks Check for cracks & bent body

Check for damaged threads or bent rods.


25

Eye & Eye Stock Code

Jaw & Jaw Stock Code

Size Inches


Weight Per Piece Pound (Jaw & Jaw)

84TRN-EE0804 84TRN-JJ0804 1/4 x 4 500 0.4084TRN-EE1004 84TRN-JJ1004 5/16 x 4 1/2 800 0.5484TRN-EE1206 84TRN-JJ1206 3/8 x 6 1,200 0.8384TRN-EE1606 84TRN-JJ1606 1/2 x 6 2,200 1.5784TRN-EE1609 84TRN-JJ1609 1/2 x 9 2,200 1.9584TRN-EE1612 84TRN-JJ1612 1/2 x 12 2,200 2.2484TRN-EE2006 84TRN-JJ2006 5/8 x 6 3,500 2.8084TRN-EE2009 84TRN-JJ2009 5/8 x 9 3,500 3.3584TRN-EE2012 84TRN-JJ2012 5/8 x 12 3,500 4.0084TRN-EE2406 84TRN-JJ2406 3/4 x 6 5,200 4.3084TRN-EE2409 84TRN-JJ2409 3/4 x 9 5,200 4.8984TRN-EE2412 84TRN-JJ2412 3/4 x 12 5,200 5.9084TRN-EE2418 84TRN-JJ2418 3/4 x 18 5,200 7.7584TRN-EE2812 84TRN-JJ2812 7/8 x 12 7,200 8.6084TRN-EE2818 84TRN-JJ2818 7/8 x 18 7,200 11.4484TRN-EE3206 84TRN-JJ3206 1 x 6 10,000 9.4484TRN-EE3212 84TRN-JJ3212 1 x 12 10,000 11.5384TRN-EE3218 84TRN-JJ3218 1 x 18 10,000 16.4084TRN-EE3224 84TRN-JJ3224 1 x 24 10,000 18.6084TRN-EE4012 84TRN-JJ4012 1 1/4 x 12 15,200 23.6084TRN-EE4018 84TRN-JJ4018 1 1/4 x 18 15,200 26.6084TRN-EE4024 84TRN-JJ4024 1 1/4 x 24 15,200 31.2084TRN-EE4824 84TRN-JJ4824 1 1/2 x 24 21,400 47.6084TRN-EE6424 84TRN-JJ6424 2 x 24 37,000 115.00

To avoid injury or property damage use turnbuckles in direct tension only. NEVER side load or exceed the working load limit. Always ensure there is thread engagement of at least 1.5 times the thread diameter.

Procraft Hot Dipped Galvanized TurnbucklesThese turnbuckles are drop forged hot dipped galvanized which meets US Federal Spec FF-T-792B Type 1, Form 1 (open Body). They are stamped and marked with size, manufacturer and traceability code to meet with the ASME standards. Procraft turnbuckles come complete with lock nuts installed on the threaded ends for safer installation practices.


26 To avoid injury or property damage know the Working Load Limit of the block, or blocks, to be used and how to use them. This product is not designed for personnel lifting. Working Load Limits are resultant Working Loads. Never exceed working load limit or wire rope size.

YARDING AND SNATCH BLOCKS are one of the most widely used blocks. It is a temporary or intermittent - service block which quickly attaches to the wire rope and moves load over comparatively short distances. This is opposed to long lifts and continuous service for which crane and construction blocks are designed. Snatch Blocks wire rope-to-sheave diameter ratio is not the same as that recommended for crane and construction blocks. Since the height and frequency of the lifts is not as critical, larger sheaves are not as crucial to snatch block operations. However, provisions should be made to increase the sheave size where the situation demands. Naturally a larger sheave is an advantage for bearing and wire rope life. The head fittings on these type of snatch blocks are NOT installed with thrust bearings, therefore the fitting will not swivel under full load.Instructions for Safe Use- Always design and rig snatch block systems so that the load will not slip or fall.- Always design the lifting system with appropriate sheave assembly material to prevent premature sheave, bear-ing or wire rope wear and failure.- Always have a qualified person rig the snatch block system. The lower fittings on snatch blocks are NOT in-stalled with thrust bearings, therefore the fitting will not swivel under full load.- Instruct workers to keep hands and body away from the block sheaves, swivels, and “pinch points” where wire rope makes contact with block parts or loads.- Do not side load snatch blocks. Side loading exerts additional force or loading which the snatch block is not designed to accommodate.- Always make sure the hook (and not the latch) supports the load.- Do not weld snatch blocks or load supporting parts.- Keep out from under a raised load and stay out of the line of force. Never lift personnel with snatch blocks.- Remove from service any snatch block that is cracked or deformed. Blocks must be inspected regularly and maintained to increase service life and to enhance safety.Inspection*Check all nuts or retaining pins for any signs of backing off due to high vibration or damage. The head fitting nut must be checked to ensure it is properly engaged into its retaining nut to full depth and the thread is locked. Also, check for excessive “play” in the head fitting. Excessive free play is a sign of wear.*Look for wear on pins, axles (check if axle is still fixed), side plates, bushings/bearings and fittings attachment points. Any excessive wear (10% wear is the maximum permissible) will require the block to be pulled from service.*Check Sheaves for wobble, misalignment, uneven groove flange wear, corrugations or wear in sheave groove. If sheave wobbles or is misaligned this indicates bearing wear which will require removal from service.*Check any head fittings for deformation or stretch. Make sure hook has not stretched and latch still fits the hook correctly. Check the shackle pin for damage or deformation.Load Angle FactorsThe stress on a snatch block varies between the degree of angle between the lead and load lines. As the angle between the lines increases, the stress on the block is reduced. With both lines parallel, 1000 pounds on the lead line results in 2000 pounds on the block. Provisions should also be made to in-crease the sheave size where the situation demands. Naturally a larger sheave is an advantage for bearing and rope life. Use the chart below to calculate the total load, by multiplying the line pull by the angle factor and then add 10% for sheave fric-tion.

ANGLE FACTOR MULTIPLIERS

Angle Factor Angle Factor

0° 2.00 90° 1.41

10° 1.99 100° 1.29

20° 1.97 110° 1.15

30° 1.93 120° 1.00

40° 1.87 130° 0.84

45° 1.84 140° 0.68

50° 1.81 150° 0.52

60° 1.73 160° 0.35

70° 1.64 170° 0.17

80° 1.53 180° 0.00


27

Stock Code

Size Inches

Working Load Limit

Tons

Wire Rope Diameter

Head Fitting


07SB-HK030 3 2 5/16 - 3/8 Hook 8.6007SB-HK040 4 1/2 4 3/8 - 1/2 Hook 13.6707SB-HK050 6 4 3/8 - 1/2 Hook 18.5207SB-HK060 6 8 5/8 - 3/4 Hook 31.0807SB-HK080 8 8 5/8 - 3/4 Hook 41.8807SB-SH030 3 2 5/16 - 3/8 Shackle 8.3807SB-SH040 4 1/2 4 3/8 - 1/2 Shackle 13.6707SB-SH050 6 4 3/8 - 1/2 Shackle 18.2907SB-SH060 6 8 5/8 - 3/4 Shackle 31.0807SB-SH080 8 8 5/8 - 3/4 Shackle 41.2207SB-SH1508 8 15 7/8 - 1 Shackle 72.7307SB-SH1210 10 12 1 Shackle 76.5007SB-TB030 3 2 5/16 - 3/8 Tailboard 4.8007SB-TB040 4 1/2 4 3/8 - 1/2 Tailboard 8.0007SB-TB060 6 8 5/8 - 3/4 Tailboard 16.0007SB-TB080 8 8 5/8 - 3/4 Tailboard 24.00

Procraft Snatch Blocks Bronze Bush Single SheaveSnatch blocks have a bronze bushing and are generally used with wire rope. They are mostly suited to applica-tions where hoisting speed are not high, and the head fitting is not designed to rotate while under load (not suit-able for concrete tilt wall panels). Snatch blocks are designed with a 4:1 factor of safety.

Stock Code

Size Inches

Working Load Limit

Tons

Wire Rope Diameter

Head Fitting


07SN-DS03J 3 1/2 5/16 Hook 3.3007SN-DS04J 4 1 3/8 Hook 5.5107SN-DS05J 5 1 1/2 1/2 Hook 10.5807SN-DS06J 6 2 5/8 Hook 16.31

Procraft Light Duty Snatch Blocks Single SheaveLight Duty Snatch blocks are suitable for synthetic or wire rope. A drop side plate allows easy access for the installation of the rope, and its light weight design aids quick installation. Snatch blocks are designed with a 4:1 factor of safety.

To avoid injury or property damage know the Working Load Limit of the block, or blocks, to be used and how to use them. This product is not designed for personnel lifting. Working Load Limits are resultant Working Loads. Never exceed working load limit or wire rope size.


28

Stock Code

Size Inches

Working Load Limit Tonnes

Maximum Diameter

Wire Rope


Single Sheave07YD-103 3 0.5 5/16 2.4207YD-104 4 1.0 3/8 3.9707YD-105 5 1.5 7/16 7.7107YD-106 6 2.0 9/16 11.24

Double Sheave07YD-203 3 0.5 5/16 3.9707YD-204 4 1.0 3/8 6.1707YD-205 5 1.5 7/16 12.1207YD-206 6 2.0 9/16 18.74

Procraft Black Painted Yarding BlocksThese yarding blocks have a bronze bushing and are mostly suited to light duty applications where hoisting speed is not high. They are perfect for entertainment rigging with the black painted finish. They are offered with ei-ther a single sheave or double sheave, and can be used with wire or synthetic ropes. Larger sizes come complete with a grease nipple for relubrication. Working load limits are in Metric Tonnes and are built with a 4:1 factor of safety.

To avoid injury or property damage know the Working Load Limit of the block, or blocks, to be used and how to use them. This product is not designed for personnel lifting. Working Load Limits are resultant Working Loads. Never exceed working load limit or wire rope size.

Stock Code

Size Inches

Working Load Limit Tonnes

Wire Rope Diameter


Single Sheave07YD-103G 3 0.5 5/16 2.4207YD-104G 4 1.0 3/8 3.9707YD-105G 5 1.5 7/16 7.7107YD-106G 6 2.0 9/16 11.2407YD-108G 8 4.0 3/4 25.3507YD-110G 10 5.0 7/8 37.47

Double Sheave07YD-203G 3 0.5 5/16 3.9707YD-204G 4 1.0 3/8 6.1707YD-205G 5 1.5 7/16 12.1207YD-206G 6 2.0 9/16 18.7407YD-208G 8 4.0 3/4 36.37

Procraft Hot Dipped Galvanized Yarding BlocksThese yarding blocks have a bronze bearing and are mostly suited to light duty applications where hoisting speed is not high. They are perfect for fishing vessels and other marine uses with the hot dipped galvanized finish. They are offered with either a single sheave or double sheave, and can be used with wire or synthetic ropes. Working load limits are in Metric Tonnes and are built with a 4:1 factor of safety.


29To avoid injury or property damage know the Working Load Limit of the block, or blocks, to be used and how to use them. This product is not designed for personnel lifting. Working Load Limits are resultant Working Loads. Never exceed working load limit or wire rope size.

Procraft Steel Sheaves with BearingCast iron sheaves with installed sealed bearings is ideal for wire rope and synthetic ropes.

Stock Code

Outside Diameter

Axle Pin Diameter (Bore)

Wire Rope Diameter


07SH-B03 3 5/8 5/16 0.9007SH-B04 4 11/16 3/8 1.5007SH-B05 5 7/8 7/16 3.5007SH-B06 6 7/8 9/16 5.8007SH-B08 8 1 1/4 3/4 15.0007SH-B10 10 1 3/8 7/8 20.00

Off Road BlocksThese blocks are perfect for winching or hauling where increased capacity in a winch line is required. The two opening cheek plates allows quick access for synthetic or wire winchline. These blocks are not suitable for over-head lifting or critical load bearing applications.

Stock Code

Sheave Diameter

Rated Capacity Pounds

Wire Rope Diameter


07ORB-104 4 4,500 7/16 4.2007ORB-105 5 12,000 9/16 7.70


30 To avoid injury inspect before use, do not overload, never use handle extenders (cheater bars) and never use grade 70 transport chains and fittings for overhead lifting. Death or injury can occur from improper use.

LOAD SECUREMENT PRODUCTS, “Any load-carrying vehicle must be loaded and driven in such a manner as to prevent danger to any person, or damage to any property” this is why it is extremely important to use and know how to use quality load securement products.Minimum Number of TiedownsEach cargo securement system must be able to withstand a mini-mum amount of force in each direction.Forward Force = 80% of cargo weight when breaking while driv-ing straight ahead.Rearward Force = 50% of cargo weight when accelerating, shift-ing gears while climbing a hill, or breaking in reverse.Sideways Force = 50% of cargo weight when turning, changing lanes, or breaking while turning.Upward Force = 20% of cargo weight when travelling over bumps in the road or cresting a hill.This requirement is satisfied when the cargo is “fully contained” All elements of the vehicle structure, anchor points and tiedowns must be strong enough to withstand the forcesdescribed above (see guide table on number of chains and tie down straps required for loads in weight on follow-ing pages).Always ensure each tiedown is attached and secured so that it does NOT become loose or unfastened, open, or release during transit.Minimum number of tie downs required will also depend upon the length of the article(s) being secured. When an article is not blocked or positioned to prevent forward movement by a bulkhead or headboard, or by other cargo that is positioned to avoid movement and other appropriate blocking devices, loads must be secured by at least:A) One Tiedown if the article is 5 feet (1.52 metres) or less in length, and 1,100 pounds (500kgs) or less in weight.B) Two tiedowns if the article is 5 feet (1.52 metres) or less in length and more than 1,100 pounds (500kgs) in weight.C) Two tiedowns if the article is longer then 5 feet (1.52 metres) but less than or equal to 10 feet (3.04 metres) in length, irrespective of weight and more than 1,100 pounds (500kgs) in weight.D) Two tiedowns if the article is longer than 10 feet (3.04 meters), and one additional tiedown for every 10 feet (3.04 meters) of article length, or fraction thereof, beyond the first 10 feet (3.04 meters) of length.Log WrappersTo determine the required amount of load encircling wrappers for long logs on logging trucks use the following formula; Aggregate working load limit of tie downs used to secure each stack shall be at least 1/6 of the weight of the stack.Example would be 35,000 kg load of long logs using 3/8” wire rope wrappers: 35,000kgs divide by 6 (1/6) = 5,833kgs 5,833kgs divided by 1,360kgs (WLL of 3/8” wrapper) = 4.28 Therefore a total of 5 load wrappers would be required to secure this load.To determine the required amount of load encircling wrappers for short logs on logging trucks use the following formula; Aggregate working load limit of tie downs used to secure each stack shall be at least 1/6 of the weight of the stack.Example would be 14,000 kg load of short logs using 3/8” wire rope wrappers:14,000kgs divide by 6 (1/6) = 2,333kgs - 2,333kgs divided by 1,360kgs (WLL of 3/8” wrapper) = 1.71 Therefore a total of 2 load wrappers would be required to secure each load.Please check with Pro Sling & Safety or the Federal Motor Carriers Safety Administration DOT Regulations for special requirements on securing Dressed Lumber, Metal Coils, Paper Rolls, Concrete Pipe, Vehicles and other special loads. Its important that you also check your local regulations to ensure that you conform to their require-ments.


31

Inspection and Care in UseAlways inspect load securement devices regularly before use. Inspect chains, hooks and binders for wear, cracks, stretch and any signs of fatigue. Inspect Web Straps and Wires for any cuts, nicks or abrasion resulting from sharp corners. If working load tags are damaged, removed or can not be read, assembly should be discarded.Use corner protectors or padding on loads with sharp edges or corners. The lashing capacity of any chain is reduced by 25% if the corner radius is less than the nominal chain size. NEVER use extender (cheater) bars on loadbinders. Always ensure that load securement devices are evenly loaded and secured so that it does NOT be-come loose or unfastened.

To avoid injury inspect before use, do not overload, NEVER use handle extenders (cheater bars) and never use grade 70 transport chains and fittings for overhead lifting. Death or injury can occur from improper use.

Grade 70 ChainDiameter

Working Load Limit Minimum number of chains required to secure loads in forward direction by weight of articles in lbs. (kgs)

(lbs) (kgs) 5,000 (2,270)

10,000 (4,540)

15,000 (6,800)

20,000 (9,070)

25,000 (11,340)

30,000 (13,600)

35,000 (15,870)

40,000 (18,140)

45,000 (20,410)

50,000 (22,680)

1/4 3,150 1,429 2 3 4 6 7 8 9 11 12 13

5/16 4,700 2,132 1 2 3 4 5 6 6 7 8 9

3/8 6,600 2,994 1 2 2 3 4 4 5 5 6 7

7/16 8,750 3,990 1 1 2 2 3 3 4 4 5 5

1/2 11,300 5,127 1 1 2 2 2 3 3 4 4 4

Stock Code

Chain Size Inches

Feet Per Drum


Weight perFoot Pounds

0807-08 1/4 400 3,150 0.940807-10 5/16 550 4,700 1.110807-12 3/8 400 6,600 1.500807-16 1/2 200 11,300 2.60

Stock Code

Chain Size Inches



38CL-A08 1/4 3,150 0.3638CL-A10 5/16 4,700 0.6238CL-A12 3/8 6,600 1.0038CL-A14 7/16 8,800 1.3138CL-A16 1/2 11,300 2.22

Procraft Grade 70 Gold Chromate Transport ChainTransport chain is used in tie down and load securement applications. It has a gold zinc plated finish for cleanli-ness and ease of identification. Procraft transport chain is produced to the NACM standards and is marked with grade and each individual link is proof load tested. DO NOT use in overhead applications and NEVER exceed the rated capacity of the chain.

Minimum number of tie down chains required to secure a load as per Federal Motor Carriers Safety Administra-tion, DOT Regulations; per 49CFR, Part 393 - Paragraph 393.102.

Procraft Grade 70 Gold Chromate Grab HooksGrade 70 Grab Hooks are to be used with Grade 70 transport chain for tie down applications. Grab hooks are designed to grab onto the chain or hook into rails. These hooks are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities.


32

Stock Code

Chain Size Inches



39CL-A08 1/4 2,750 0.5539CL-A10 5/16 4,300 0.7939CL-A12 3/8 5,250 1.2139CL-A14 7/16 7,000 2.0639CL-A16 1/2 9,000 2.75

Procraft Grade 70 Grab Hooks Trigger Safety (Latch)Grade 70 Grab Hooks are to be used with Grade 70 transport chain for tie down applications. Grab hooks are designed to grab onto the chain or hook into rails. These hooks are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities.

Stock Code

Chain Size Inches



38CL-AP12 3/8 6,600 1.2038CL-AP16 1/2 11,300 2.60

Procraft Grade 70 Gold Chromate Slip HooksGrade 70 Slip Hooks are to be used with Grade 70 transport chain for tie down applications. Slip hooks are designed to slip onto the chain or hook into rails. These hooks are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities. Hooks come with or without a safety latch, please advise the preferred type at time of order.

Procraft Grade 70 Slip Hooks with Latch Kit Grade 70 Slip Hooks are to be used with Grade 70 transport chain for tie down applications. Slip hooks are designed to slip onto the chain or hook into rails. These hooks are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities. This hook comes with a safety latch installed for increased safety.

Stock Code

Chain Size Inches



39CL-AL08 1/4 2,750 0.6539CL-AL10 5/16 4,300 0.9239CL-AL12 3/8 5,250 1.3239CL-AL14 7/16 7,000 2.0739CL-AL16 1/2 9,000 2.90

To avoid injury inspect before use, do not overload, NEVER use handle extenders (cheater bars) and never use grade 70 transport chains and fittings for overhead lifting. Death or injury can occur from improper use.


33To avoid injury inspect before use, DO NOT overload, never use handle extenders (cheater bars) and NEVER use grade 70 transport chains and fittings for overhead lifting. Death or injury can occur from improper use.

Stock Code

Chain Size Inches


Weight Per Piece Pounds

04ST-08 1/4 G7 2,600 3.6304ST-12 5/16 G7 to 3/8 G4 5,400 7.9304ST-16 3/8 G7 to 1/2 G4 9,200 12.56

Stock Code

Chain Size Inches



04RA-10 1/4 G7 to 5/16 G4 3,900 3.6804RA-12 5/16 G7 to 3/8 G4 5,400 10.9504RA-16 3/8 G7 to 1/2 G4 9,200 12.96

Procraft Forged Lever Type Loadbinders (Cinches)Procraft Load Binders are forged, quenched and tempered with each binder being proof load tested. The all forged design is better suited to the cold environments than cast product, and will yield or stretch before failing. Loadbinders are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities and NEVER use handle extenders or “cheater” bars.

Procraft Forged Ratchet Loadbinders (Cinches)Procraft Ratchet Load Binders have a ratchet handle with an open design using locking bolts. The open handle allows the user to simply strike with a hammer or other tool, and any substances (ice, snow and dirt) that may interfere with the ratchet system will be removed. They are forged, quenched and tempered with each binder be-ing proof load tested. The all forged design is better suited to the cold environments than cast product, and will yield or stretch before failing. Loadbinders are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities and NEVER use handle extenders or “cheater” bars.

Procraft Forged Ratchet Loadbinders with Safety PinThis Ratchet Load Binders is manufactured to European Standard EN12195-3 and are suitable for use with Grade 80 alloy chain and the grab hooks have safety pins for increased safety. They are forged, quenched and tempered with each binder being proof load tested. Loadbinders are suitable for load securement and are NOT to be used for overhead lifting. DO NOT exceed rated capacities and NEVER use handle extenders or “cheater” bars.

Stock Code

Chain Size Inches

Lashing CapacitykN (Pounds)


04RA08-16CPL 1/2 100 (22,480) 16.53

Open handle design using lock nuts

Open handle designs allow user eaiser cleaning of dirt and grit.


34 To avoid injury inspect before use, check webbing for cuts and abrasion. Protect any web belts from sharp corners or edges. Always ensure you are using the correct strap for the load or job. Never exceed rated capacities. Death or injury can occur from improper use.

WebbingWidth

Working Load Limit Minimum number of web straps required to secure loads in forward direction by weight of articles in lbs. (kgs)

(lbs) (kgs) 5,000 (2,270)

10,000 (4,540)

15,000 (6,800)

20,000 (9,070)

25,000 (11,340)

30,000 (13,600)

35,000 (15,870)

40,000 (18,140)

45,000 (20,410)

50,000 (22,680)

2 3,335 1,512 2 3 4 5 6 8 9 10 11 12

3 4,300 1,950 1 2 3 4 5 6 7 8 9 10

4 5,400 2,449 1 2 3 3 4 5 6 6 7 8

Stock Code Style Mounting Rated Capacity Pounds


44WN-PRT Standard Portable 5,000 10.5044WN-PRTLP Low Profile Portable 5,000 10.5044WN-REG Standard Weld-On 5,400 9.2044WN-RHM Low Profile Weld-On 5,400 9.1044WNBAR-

COMBOCombination Winch Bar » » 5.90

44WN-WNDR Strap Winder » » 2.5044WN Lashing Winch Bolt-On 3,335 3.10

44CAP-04 2 & 4” Wide Plastic Corner » » 0.30

Stock Code Description Rated Capacity

PoundsWeight per

Piece Pounds90TIE-4D25YEL 4" x 25 ft Dee Ring 5,400 5.0090TIE-4D30YEL 4” x 30 ft Dee Ring 5,400 6.2090TIE-4D40YEL 4" X 40 ft Dee Ring 5,400 8.0090TIE-4F30YEL 4” x 30 ft Flat Hook 5,400 6.2090TIE-4F40YEL 4” x 40 ft Flat Hook 5,400 8.00

Procraft Web Tie Down StrapsProcraft web tie down straps are light weight and are simple to use. They are a cost effective product to use in place of chain, but can be more easily damaged and prone to being cut on sharp edges and should NOT be used on certain loads. Procraft straps are manufactured to the WSTDA standards for increased strength and durability, and come complete with rated capacity tags.

Minimum number of tie down web straps required to secure a load as per Federal Motor Carriers Safety Admin-istration, DOT Regulations; per 49CFR, Part 393 - Paragraph 393.102.

Procraft 4” Truck Winch StrapsWinch straps are used in conjunction with truck winches on flat bed trucks and large trailers. Make sure winch straps are protected from sharp corners when securing to the load. Straps can be manufactured to customers re-quirements including varying lengths, special end fittings and ink marked with companies name.

Procraft 4” Truck Winch Straps & AccessoriesWinches are available as portable or weld on units, easily installed on flat bed trucks, trailers, and railcars. Used in conjunction with either 3” or 4” winch straps they can be lighter and easier to handle than chain and loadbind-ers. Extra care should be taken with the webbing on sharp corners.


35To avoid injury inspect before use, check webbing for cuts and abrasion. Protect any web belts from sharp corners or edges. Always ensure you are using the correct strap for the load or job. Never exceed rated capacities. Death or injury can occur from improper use.


PoundsWeight per

Piece Pounds90TIE-3SET30F Flat Hooks 3” x 30 ft 5,000 12.44

90TIE-3SET30WH Wire Hooks 3” x 30 ft 5,000 14.3090TIE-2SET30F Flat Hooks 2” x 30 ft 3,335 6.00

90TIE-2SET30W16 HD Wire Hooks 2” x 30 ft 3,335 5.8090TIE-2SET25W16 HD Wire Hooks 2” x 25 ft 3,335 5.4090TIE-2SET20W16 HD Wire Hooks 2” x 20 ft 3,335 5.0090TIE-2SET15W16 HD Wire Hooks 2” x 15 ft 3,335 4.60

90TIE-2RL08 Ratchet Loop Strap 2” x 8 Ft 3,335 3.40




90TIE-2SET12E ‘E’ Track Fittings with LD Ratchet 2” x 12 ft 1,000 1.00

90TIE-ROPEE ‘E’ Track Tie Off & Dee Ring 1,000 1.00


PoundsWeight per

Piece Pounds90TIE-

1X10WSET1” x 10ft

Wire Hooks 1,000 1.50

90TIE- 1X12WDSET

1” x 12 ft Wire Hooks & Dee Ring 1,000 1.40

90TIE- 1X20WDSET

1” x 20ft Wire Hooks & Dee Ring 1,000 1.60


90TIE-1R20 Ratchet Loop Strap 1” x 20 Ft 1,000 1.40

Procraft 3” & 2” Web Ratchet Tie Down SetsThis type of ratchet tie down is one the most commonly used tie down for general use and is suitable for a wide range of applications including flat bed trucks and van tie downs. Standard assemblies come complete with fixed end, but can be manufactured to customers specifications and requirements. DO NOT use a cheater bar to in-crease leverage on ratchets.

Procraft 1” Web Ratchet Tie Down StrapsThese straps are commonly used for small utility or van tie downs. Standard assemblies come complete with 9” fixed end, but can be manufactured to customers specifications. DO NOT use a cheater bar to increase leverage on ratchets.


36 To avoid injury or property damage never use commercial grade chains for overhead lifting or any critical load bearing applications. Always inspect chain before use, and never use a worn or damaged chain.

COMMERCIAL GRADE CHAINS are commonly used in many marine, light industrial, hardware and general applications. All commercial grade chains are NOT to be used in overhead lifting or critical load bearing applica-tions. This chain will fail without warning or notice, for any lifting applications please see our Grade 80 & Grade 100 chains. The chain is available in four different finish types, with each type having separate qualities and at-tributes. Self Colour / Bright chain is the steel in its raw form with no anti-rust protection applied. It is used as a cheaper cost alternative to other chains where it will not be subject to environmental conditions. It is also used in mooring applications where the chain is fully submerged. The chain has a tan or brown colour. Hot Dipped Galvanized is a Zinc coating applied to the chain after manufacture. Its gives great rust protection so is heavily used in the marine and coastal areas. It is a cost effective alternative to Stainless Steel. It generally has a dull grey and slightly uneven surface. Zinc Plated process adds a very fine zinc finish to the chain. The finish is around 10 times thinner than that of Hot Dip Galvanized and so will not have the rust protection of Hot Dipped Galvanized Chain. This chain is very popular for indoor uses or where a nice finish is preferred due to its silver and smooth finish.Stainless Steel is manufactured from 316 stainless steel and has the highest resistance to corrosive environments. Its the most expensive of all the chain types and has the least strength, but can be used in many marine environ-ments, acidic areas and food preparation areas. The smooth finish also makes it popular as a decorative chain.

Stock Code Diameter Length Per Drum

Inside Dimensions

(L x W)

Breaking Strength Pounds

Weight per Foot Pounds

08PR-T*04 1/8 500 0.94 x 0.22 1,600 0.2008PR-T*06 3/16 500 0.98 x 0.30 3,200 0.4008PR-T*08 1/4 800 1.24 x 0.38 5,200 0.6608PR-T*10 5/16 550 1.29 x 0.44 6,800 0.8608PR-T*12 3/8 400 1.38 x 0.55 10,600 1.4208PR-T*16 1/2 200 1.79 x 0.72 17,900 2.42

Procraft Grade 30 ChainGrade 30 chain is a low carbon chain used for many hardware type applications and light duty marine use. Our chain is all machine welded and each link is proof load tested. This chain is NOT suitable for overhead lifting or any critical load bearing applications

* Insert the following letters for the stock code on finish types, G - Galvanized, S - Self Colour/Bright & Z - Zinc Plated


37

Stock Code Diameter Length Per Drum

Inside Dimensions

(L x W)


Weight Per Foot Pounds

08SS-04 1/8 500 0.94 x 0.25 1,600 0.2008SS-06 3/16 500 0.98 x 0.30 3,200 0.4008SS-08 1/4 800 1.24 x 0.38 5,200 0.6608SS-10 5/16 550 1.29 x 0.44 7,600 0.9608SS-12 3/8 400 1.38 x 0.55 10,600 1.42

Stock Code

Chain Size Inches Length

Inside Dimensions

(L x W)



08MO-GV12 3/8 (GV) 200 2.36 x 0.63 10,000 1.1808MO-GV16 1/2 (GV) 200 3.23 x 0.98 17,000 1.9808MO-GV20 5/8 (GV) 150 3.75 x 0.91 26,500 2.9508MO-GV24 3/4 (GV) 200 4.92 x 2.95 42,082 4.6608MO-SC24 3/4 (SC) 200 4.92 x 2.95 42,082 4.6608MO-GV32 1 (GV) 200 6.10 x 3.93 78,859 7.7508MO-SC32 1 (SC) 200 6.10 x 3.93 78,859 7.7508MO-SC36 1 1/8 (SC) 100 6.60 x 3.98 91,268 10.9308MO-SC40 1 1/4 (SC) 100 6.80 x 4.00 102,220 11.56

Procraft 316 Stainless Steel ChainStainless steel chain is used widely in the marine environment. It is an excellent all purpose chain manufacturedfrom grade 316 stainless steel. DO NOT use in overhead lifting or any critical load bearing applications.

Procraft Long Link Mooring ChainLong link mooring chain is used extensively for mooring and anchoring docks, floats and buoys. The oversized long links is more acceptable to shackles passing directly into the chain links. This chain is a low carbon chain and is not suitable for heavy mooring applications (check stud link anchor chain).

Procraft ChainsProcraft also have available other chains for specialized applications including alloy mooring / boom chains and deck lashing chains for the shipment of logs on transport ships.

Stock Code

Chain Size Inches Length

Inside Dimensions

(L x W)



Galvanized Deck Lashing Chain08DL-LLG16 1/2 (GV) 200 3.25 x 0.79 48,000 3.68

Alloy Galvanized Boom Chain08BM-GV24 3/4 (GV) 200 3.00 x 1.10 75,000 5.03

To avoid injury or property damage never use commercial grade chains for overhead lifting or any critical load bearing applications. Always inspect chain before use, and never use a worn or damaged chain.


38 This product is designed for non load rated chains and fittings. To avoid injury or property damage. DO NOT use this type of product in any critical load bearing or lifting applications.

CHAIN CONNECTING LINKS are used for easy connection of commercial type chains. These types of con-necting links are NOT suitable for any lifting or critical load bearing applications but can be used in conjunction with small diameter chains to form a connection point between two chains or as an attachment point.

Stock Code

Size Inches



Double Clevis Links40DC-08 1/4 2,600 0.4440DC-12 5/16-3/8 5,400 0.8140DC-14 7/16 7,000 1.2840DC-16 1/2 9,200 1.68

Twin Clevis Links40TC-08 1/4-5/16 4,700 0.3140TC-12 3/8 6,600 0.4440TC-14 7/16-1/2 11,300 0.97

Stock Code

Size Inches


40RC-Z08 1/4 0.0740RC-Z12 5/16 0.1040RC-Z14 3/8 0.1840RC-Z16 1/2 0.38

Procraft Double & Twin Clevis LinksClevis links are gold chromate finish and designed for quick connection between Grade 30, 40 & 70 chain to Eyebolts, Padeyes, Hooks, Chain and Rings. DO NOT use this type of attachment on lifting chains.

Procraft Cold ShutsCold shuts are manufactured from mild zinc plated steel and are designed to form a connection between chain and fittings. DO NOT use this type of attachment on lifting chains and they should never be reused once fittings has been closed.


39This product is designed for non load rated chains and fittings. To avoid injury or property damage. DO NOT use this type of product in any critical load bearing or lifting applications.

Stock Code

Size Inches



40MIG-06 3/16 800 0.0340MIG-08 1/4 1,400 0.0640MIG-10 5/16 2,000 0.1040MIG-12 3/8 2,800 0.1840MIG-16 1/2 4,750 0.3840MIG-20 5/8 7,250 0.72

Procraft Galvanized Missing LinksMissing links are commonly used to connect two chain lengths such as an anchor chain. To ensure positive con-nections use the correct size for the chain, and ensure you peen the prongs to fill the hole of the paired half as much as possible. These fittings are NOT to be used for lifting or critical load bearing applications.

Stock Code

Size Inches



40RL-08/40 1/4 x 2 400 0.0940RL-10/64 5/16 x 2 700 0.1440RL-12/52 3/8 x 2 1,250 0.2540RL-16/80 1/2 x 2 1/2 1,525 0.54

Procraft Repair (Lap) LinksRepair / Lap links are manufactured from zinc plated mild steel and are designed to form a connection between chain and fittings, especially useful as a quick and easy repair link on Tire Chains. DO NOT use this type of at-tachment for lifting, and they should never be reused once fittings have been closed.


40 This product is designed for non load rated chains and fittings. To avoid injury or property damage. DO NOT use this type of product in any critical load bearing or lifting applications.

Stock Code

Size Inches

Opening Inches

Inside Dimensions


40SNP-06 3/16 1/4 1/4 x 2 1/8 0.0440SNP-08 1/4 5/16 5/16 x 2 1/2 0.0840SNP-10 5/16 7/16 7/16 x 3 1/8 0.1540SNP-12 3/8 1/2 1/2 x 3 5/8 0.2340SNP-14 7/16 3/4 5/8 x 4 3/4 0.3840SNP-16 1/2 1 11/16 x 5 1/2 0.58

Retainer / Eyelet40SNP-R08 1/4 5/16 5/16 x 2 1/2 0.0840SNP-R10 5/16 7/16 7/16 x 3 1/8 0.1540SNP-R12 3/8 1/2 1/2 x 3 5/8 0.23

Stainless Steel40SNP-SS08 1/4 5/16 5/16 x 2 1/2 0.0840SNP-SS10 5/16 7/16 7/16 x 3 1/8 0.1540SNP-SS12 3/8 1/2 1/2 x 3 5/8 0.23

Stock Code

Size Inches


Opening Inches

Inside Dimensions


40RQ-04 1/8 220 1/8 7/16 x 1 1/8 0.0340RQ-06 3/16 660 3/16 9/16 x 1 5/8 0.0540RQ-08 1/4 880 1/4 5/8 x 1 13/16 0.0740RQ-10 5/16 1,760 5/16 3/4 x 2 1/4 0.1640RQ-12 3/8 2,200 3/8 13/16 x 2 1/2 0.2240RQ-14 7/16 2,650 1/2 7/8 x 2 3/4 0.3240RQ-16 1/2 3,300 9/16 1 x 3 1/4 0.51

Stainless Steel40RQ-08 1/4 875 1/4 5/8 x 1 13/16 0.0740RQ-10 5/16 1,525 5/16 3/4 x 2 1/4 0.1640RQ-12 3/8 2,300 3/8 13/16 x 2 1/2 0.22

Procraft Zinc Plated Quick LinksQuick links provide an easy to use solution for attaching chain and wire rope. DO NOT use this type of attach-ment on lifting chains or slings as they are not suitable for lifting or any critical load bearing applications.

Procraft Zinc Plated Snap LinksSnap links provide an easy to use solution for attaching chain and wire rope. They come with or without an eyelet which traps the cable in the snap end. DO NOT use for any overhead lifting or load bearing applications.


41To avoid injury or property damage ensure that the users has sufficient experience in installing this product. These products are not suited for any lifting or critical load bearing applications.

Stock Code

Hook Size



36SN-G14 7/16 750 0.2336SN-G18 9/16 1,000 0.48

Stock Code

Size Inches

Hole Diameter

Opening Inches


36SN-Z08DI 4 3/4 3/4 0.56

Stock Code Size Overall

LengthWeight per

Piece Pounds36BC-SHK08 # 8 1/4" 3/4 0.1536BC-SHK10 # 10 5/16" 1 0.2836BC-SHK12 # 12 3/8" 1 1/2 0.33

Procraft Galvanized Snap HooksSnap hooks are suitable for light weight rigging and general purpose use. They are galvanized with forged trace-ability on each piece. They have a 4:1 factor of safety and you should NEVER exceed Working Load Limits.

Procraft Zinc Plated Eye Snap HookThis snap hook is generally used in conjunction with tie down webbing or wire rope as quick attachment point. This hook is NOT suitable for any lifting or load bearing applications.

Procraft Zinc Plated ‘S’ Hooks‘S’ Hooks are used for attaching accessories to chain, and also as a side chain end hook for tire chains. Ensure the ‘S’ is closed to prevent disengagement. This type of fitting is NOT load rated and should NEVER be used for overhead lifting or critical load bearing applications.


42 To avoid injury and property damage, be sure to use the correct size of chain and anchor for your application. If unsure please consult Pro Sling or a marine engineer specialising in the marine environment.

Procraft Danforth AnchorsAnchors are generally sized by its weight in the air. Its holding power is determined by the anchors efficiency multiplied by the weight of the anchor. Anchor efficiency is determined by design, testing and the type of soils which the anchor is used in. Danforth Anchors are for smaller recreational vessels including power boats and sail boats.

Stock Code Weight Each06DNFT-G22 22 Pounds06DNFT-G30 30 Pounds06DNFT-G44 44 Pounds

Stock Code Head Weight Description Weight per Piece Pounds

80HSL-H03 3 lbs 18" Oregon Handle 3.15

80HSL-H04FG 4 lbs Soft 16" Composite Handle 5.25





Procraft Sledge HammersSledge hammers have a wide variety of uses in Rigging Applications, including installation of Rafting Dogs and Wire Rope Staples. They are supplied with a heavy duty composite handle which can handle all heavy duty ap-plications.


43

Procraft Zinc Plated Rafting DogsRafting Dogs are used extensively in the marine and logging industry. They are used to secure wire and strand to logs and timber in a safe and efficient manner. These products are not suited for any lifting or critical load bear-ing applications.

Stock Code

Size Inches

Rafting Dog Type


44DOG-16 1/2 Hammer Head 0.6044DOG-20 5/8 Hammer Head 0.93

Stock Code

Material Diameter Size Inches

Length Inches


66WR-124 3/8 4 0.2966WR-1245 3/8 4-1/2 0.3066WR-164 1/2 4 0.5666WR-1645 1/2 4-1/2 0.6366WR-165 1/2 5 0.7066WR-166 1/2 6 0.8466WR-2055 5/8 5-1/2 1.1066WR-206 5/8 6 1.2066WR-208 5/8 8 1.40

Procraft Zinc Plated Wire Rope StaplesWire Rope Staples are used extensively in the marine and logging industry. They are used to secure wire and strand to logs and timber in a safe and efficient manner. These products are not suited for any lifting or critical load bearing applications.

Staples and Rafting Dogs are NOT to be used for critical load bearing applications or overhead lifting.

Lift with Experience

Ratings shown in this catalogue are based upon the items being new or in “as new” condition. Strengths are shown in either working load limit or rated capacity which is the maximum load that should be applied to the product, or breaking strength where the product must be used with an appropriate design factor applied to calculate the rated capacity of the product. All details are correct at time of printing and specifications may change without notice. It is the customers responsibility to determine the suitability of the product to its intend-ed use, including all industry regulations and guidelines. Careful inspection of any lifting and rigging product is highly recommended for any wear, deformation and misused prior to use.

www.proslingsafety.com© Copyright Wesco Industries Ltd. 2012

Head Office Unit 17, 3 Brewster Rd.Brampton ON L6T 5G9

Ph: 905 794 3330 Fx: 905 794 1345

Email: [email protected]

Documents

Procraft Rigging Products - Pro Sling & Safety · Pro Sling & Safety Inc. Procraft Rigging Products Never Exceed Working Load Limit. It is the users responsibility to determine the