Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Processing instructions
Shades – 9 A–D shades (A1, A2, A3, A3.5, A4, B1, B2, B3, C2)
– 2 Bleach shades (BL1, BL3)
Shade selectionThe tooth shade is determined with the help of a shade guide
according to the A–D shade system and the Ivoclar Vivadent Bleach
shades. Shade selection with the patient should be carried out under
defined light conditions (5,500K color temperature) during daylight
(preferably light from the north).
Anterior tooth selectionIf possible, the anterior teeth should be selected directly with
the patient.
The following reference points are determined with the help of a
model analysis:
a) Position of the central incisors in the maxilla
The labial surface of the central incisors is aligned at a distance
of 7 mm to the center of the incisive papilla.
b) Position of the canines
Identify the first large pair of rugae; the midpoint of the labial
surface of the upper canines is aligned at a distance of 9 mm.
The length of the dental arch measured across these three points
can be used as a reference to select a set of anterior teeth with
an appropriate width from the tooth mould chart.
Occlusal conceptThe SR OrthotypTM S is the classic choice for use in complete, partial
and hybrid denture prosthetics.
The Orthotyp teeth are set-up in accordance with a normal bite
situation in a one-to-two relation. In this way, the primary contacts
in the centric position are located in the central fossae in the
mandible as well as on the marginal ridges.
The lingualized occlusal concept of the SR OrtholingualTM S is
particularly suitable for implant prosthetics.
Minimum layer thicknesses It must be ensured that the stability of the teeth and the correct shade
effect are maintained. It is therefore recommended not to reduce
teeth beyond the minimum layer thickness.
• Anteriorteeth:2.5mm
• Posteriorteeth:Centralfossamin.2.0mm,cusptipsmin.2.5mm,
cervicalareamin.2.5mm.
To ensure that removable dentures remain functional over longer
periods of time, the following prerequisites should be met:
– The dentures should be planned and fabricated in close
cooperation with the dentist.
– Dentist and dental technician should ensure a balanced
occlusion and articulation.
– All dental products should be used according to the instructions
of the manufacturer. Denture teeth, in particular, should not be
weakened by excess grinding.
– In order to ensure a reliable bond with the denture base material,
the teeth are cleaned with steam, roughened and wetted with
monomer. When completing the dentures with an auto-curing
polymer, also using mechanical retentions is recommended.
– The application of a glaze varnish or denture cleaning spray is
not recommended.
– The teeth should not come into contact with a flame or direct
heat.
– Heat development as a result of too much pressure during
grinding must be prevented.
– We recommend wearing a face mask and using extraction
equipment for protection against grinding dust.
– Cleaning is performed with commercial cleaning agents.
Contact with solvents must be prevented.
– Do not use if the patient is known to be allergic to any
componentof the product.
The most important principles of lingualized occlusion were taken into
consideration for the design of the SR Ortholingual S.
The centric contacts are concentrated in the mandibular fossae with
the maxillary palatal cusps. The buccal cusps do not come into contact
with each other.
Lingualizedocclusion
One-to-onesetup
Conventionalocclusion
One-to-twosetup
6724.indd 1 2/5/14 1:35 PM
REMOVABLE
©2014 ivoclar Vivadent, inc.ivoclar Vivadent, sr ortholingual, sr orthotyp and sr Vivodent are registered trademarks of ivoclar Vivadent667082 rev 1 1/2014
UnitedStates175 Pineview DriveAmherst, new York 14228716-691-0010800-533-6825Fax: 716-691-2285www.ivoclarvivadent.com
Canada1 - 6600 Dixie roadMississauga, ontario L5t 2Y2905-670-8499800-263-8182Fax: 905-670-3102www.ivoclarvivadent.com
100% CUSTOMER SATISFACTIONG U A R A N T E E D !
ivoclarvivadent.com
Facebook “f ” Logo CMYK / .eps Facebook “f ” Logo CMYK / .eps
coMbinAtion tAbLe
SR Vivodent® S SR OrthotypTM S (22°)
SR OrtholingualTM S (15°)
Maxilla Mandible Semi-anatomical Lingualized
SmallSoft A13 A3 NU3 / NL3 LU3 / LL3
Bold P3 A3 NU3 / NL3 LU3 / LL3
MediumSoft P6, A26 A6 NU5 / NL5 LU5 / LL5
Bold A66 A6 NU5 / NL5 LU5 / LL5
LargeSoft P9 A8 NU6 / NL6 LU6 / LL6
Bold A27, P12 A8 NU6 / NL6 LU6 / LL6
This Combination Table is recommended as a guideline. In special clinical situations, deviations may be possible.
6724.indd 2 2/5/14 1:35 PM
Vivodent® SSR
Mid-line Denture Teeth
Tooth mould chartSRVivodentSSROrthotypSSROrtholingualS
REMOVABLEI V O C L A R V I V A D E N T
More than dentures.
6724.indd 3 2/5/14 1:36 PM
Vivodent SSR
OrthotypTM SSR
OrtholingualTM SSR
Soft Bold
N
L3
NU
3
LL3
LU
3
9.6
8.6
9.3
8.5
A13 P3
A3
42.8 42.6
31.7
8.4 8.0
4.7
10.2
10.6
9.7
sMALL
Dimensions in mm
29.8
32.3
32.5
31.1
6724.indd 4 2/5/14 1:36 PM
Vivodent SSR
OrthotypTM SSR
OrtholingualTM SSR
Soft Bold
N
L5
NU
5
LL5
LU
5
10.3
9.3
9.9
9.0
P6 A66
A26
A6
44.5 45.6
47.0
35.0
8.5 8.7
8.8
5.2
10.7
10.7
11.4
9.6
MeDiuM
Dimensions in mmDimensions in mm
32.2
34.8
32.6
34.3
6724.indd 5 2/5/14 1:37 PM