Probe System Equipment MT/VAST - Metro Place · Email: [email protected] Version: V2011_07_E_3.04 Content ... MT/VAST. 3 Productivity for your ZEISS measuring machine As the manufacturer

I n d u s t r i a l M e t r o l o g y f r o m C a r l Z e i s s

Probe System Equipment MT/VASTOriginal accessories from the technology leader

www.probes.zeiss.com

2 © Carl Zeiss 3D Automation GmbH

ImprintCarl Zeiss 3D Automation GmbH

Schnaitbergstr. 3

D-73457 Essingen bei Aalen

Tel.: +49-7365-9208-210

Fax: +49-7365-9208-29

Email: [email protected]


Version: V2011_07_E_3.04

ContentStyli ........................................................................ 5

Stylus Extensions .....................................................21

Plate Extensions ..................................................... 29

Connecting Elements .............................................31

ThermoFit® Pro ...................................................... 39

Styli Kits M5 ............................................................51

Adapter Plates ....................................................... 59

Temperature Sensor ............................................... 65

Changer Racks ....................................................... 69

Stylus Set-up Device ................................................77

Probe Cabinets ....................................................... 79

Tools ..................................................................... 83

CMM Accessories ................................................... 87

Clamping Systems .................................................. 93

Request Styli M5 ...................................................102

Original accessories from Carl Zeiss

Important Notice:Prices are subject to change.

Styli and accessory components are subject to

technical modifications and changes.

Prices are net without deduction.

All dimensions are in mm.

Pictures can differ from actual products.

You can find our full T&C at:

www.probes.zeiss.com (Imprint)

Accessories optimized for

MT/VAST.

www.probes.zeiss.com 3

Productivity for your ZEISS measuring machine

As the manufacturer of coordinate measuring

machines, we know exactly what is needed for

accurate and efficient measurements. With our

especially for the ZEISS CMMs and probes designed

accessories you can save time and increase your

productivity. Benefit from our extensive know-how

and from our experience.

Largest range of original Carl Zeiss accessories

Save time

Visible productivity

Unrivaled as a service provider

Fixtures, robot automation, custom-made

styli - we assist you with our know-how in every

individual measuring project you might have.

Tried and tested

Our team supplies you fast and worldwide with our

original accessories. You can always find the right

accessory for your application in our clearly struc-

tured online shop www.probes.zeiss.com

Carl Zeiss 3D Automation GmbH

You can always rely on Carl Zeissoriginal products and on our service


Largest range of original ZEISS accessories

Become a registered user today and benefit from

the advantages of our clearly structured online

shop.

Check availabilities and the status of your orders

online. Never miss any of our special offers and

keep yourself always up-to-date on our newest

additions to our program.


Schnaitbergstr.3

D-73457 Essingen bei Aalen

Tel.: +49-7365-9208-210

Fax: +49-7365-9208-29

Email: [email protected]


Global availability


Use our online shop for a fast and easy order process.

All over the world and around the clock.


Styli with sphere / carbide shaft

Styli with a carbide shaft are characterised by their

high stiffness. Carbide shafts are used in styli with

small shaft-diameters or in stepped styli. With large

shaft diameters and/or long styli, weight could be

an issue. In those cases we recommend using styli

with carbon fibre shafts instead.

Straight shaft / ruby sphere

Styli with a ruby sphere and a straight carbide

shaft are used in all standard applications. Ruby is

an extremely hard material that can be shaped into

a very accurate sphere.

More sizes on request.

Styli

Art-Nr DK L ML DS DG weight (g)

626115-0140-033 1,35 32,85 23,85 1,00 11,00 5,5626115-0150-033 1,50 33,00 24,00 1,00 11,00 5,5626115-0200-020 2,00 20,00 9,00 1,00 11,00 5,6626115-0200-034 2,00 33,50 24,50 1,50 11,00 5,8626115-0204-040 2,00 40,00 30,00 1,50 11,00 6,6626115-0250-020 2,50 20,00 10,00 1,50 11,00 6,0626115-0250-034 2,50 34,00 25,00 1,50 11,00 6,0602030-9010-000 3,00 25,00 15,00 2,00 11,00 4,0600342-8020-000 3,00 33,50 23,50 2,00 11,00 4,0626115-0301-040 3,00 40,00 30,00 2,00 11,00 7,1602030-9011-000 3,00 50,00 40,00 2,00 11,00 5,0600342-8021-000 3,00 58,00 48,00 2,00 11,00 6,0600342-8025-000 4,00 33,50 23,50 2,00 11,00 4,0000000-1005-246 4,00 40,00 30,00 2,00 11,00 6,0626115-0402-050 4,00 50,00 40,00 2,00 11,00 9,5602030-9012-000 4,00 64,00 54,00 2,00 11,00 6,0626115-0500-040 5,00 40,00 28,00 3,50 11,00 11602030-9013-000 5,00 50,00 40,00 3,50 11,00 9,0600342-8022-000 5,00 53,00 43,00 3,50 11,00 9,8602030-9015-000 5,00 75,00 65,00 3,50 11,00 13626115-0502-080 5,00 80,00 70,00 3,50 11,00 19600342-8026-000 6,00 54,00 44,00 3,50 11,00 10626115-0600-068 6,00 68,00 55,00 3,50 11,00 13600342-8027-000 7,00 55,00 45,00 3,50 11,00 10600342-8023-000 8,00 63,50 50,50 6,00 11,00 25602030-9016-000 8,00 75,00 62,00 6,00 11,00 30602030-9017-000 8,00 100,00 87,00 6,00 11,00 41600342-8024-000 8,00 114,50 101,50 6,00 11,00 48600342-8029-000 10,00 65,50 52,50 6,00 11,00 27602030-9018-000 10,00 118,00 105,00 6,00 11,00 47626115-1200-065 12,00 65,00 52,00 6,00 11,00 29626115-1200-118 12,00 118,00 105,00 6,00 11,00 62626115-1400-065 14,00 65,00 52,00 6,00 11,00 33626115-1402-118 14,00 118,00 105,00 6,00 11,00 64


Stepped shaft / ruby sphere

Art-Nr DK L ML MLE DS DSE DG weight (g)

626115-0021-025 0,20 25,00 14,00 1,30 1,00 0,10 11,00 4,3626115-0030-022 0,30 21,80 12,80 2,30 1,00 0,20 11,00 6,0626115-0050-022 0,50 22,00 13,00 2,50 1,00 0,30 11,00 6,0626115-0060-022 0,60 22,10 13,10 4,60 1,00 0,40 11,00 5,4626115-0080-022 0,80 22,30 13,30 4,80 1,00 0,60 11,00 6,0602030-8060-000 0,80 32,00 12,00 4,80 1,00 0,60 11,00 4,0626115-0100-022 1,00 22,50 12,50 5,00 1,00 0,80 11,00 6,0

602030-8061-000 1,00 32,00 12,00 5,00 1,00 0,80 11,00 4,0602030-8062-000 1,35 32,00 12,00 1,00 11,00 4,0602030-8063-000 1,35 44,00 19,00 1,00 11,00 4,0602030-8064-000 1,50 32,00 12,00 1,00 11,00 4,0602030-8065-000 1,50 44,00 19,00 1,00 11,00 4,0602030-8066-000 2,00 32,00 12,00 1,50 11,00 7,2602030-8067-000 2,00 44,00 19,00 1,50 11,00 5,0602030-8068-000 2,00 58,00 33,00 1,50 11,00 5,0602030-8069-000 2,50 32,00 12,00 1,50 11,00 4,0602030-8070-000 2,50 44,00 19,00 1,50 11,00 5,0602030-8071-000 2,50 58,00 33,00 1,50 11,00 5,0

Styli with a ruby sphere and a stepped carbide

shaft are used in all standard applications, in which

easy accessibility with small styli with sphere is

essential. Ruby is an extremely hard material that

can be shaped into a very accurate sphere.

Styli


RubyStyli with ruby spheres are commonly used for all

standard applications. Ruby is an extremely hard

material and can be ground into highly accurate

spheres.


Styli

Diamond styli

Diamond is the hardest material known in the

world. Due to its outstanding properties, it opens

up completely new applications for scanning of

extremely hard or soft materials. When scanning

soft aluminum alloys with Diamond!Scan styli, no

material build-up occurs. When scanning hard

ceramics or cast iron, no wear can be observed on

the sphere.

Test Dimond!Scan and profit from its advantages:

- less down time of your cmm due to fewer

changes of used styli

- more stable and confident measuring processes,

because the sphere does not change its shape.

Scanning stylus with thread M5, shaft tungsten

carbide shaft and diamond sphere. The deviation

from the perfect sphere is below 0,25 µm. The

diameter tolerance is +/-20 µm. Special lengths

can be provided upon request.

Diamond• the expert for extreme scanning

• no wear

• no material build-up

• visible productivity

More lengths on request.

Art-Nr DK L ML MLE DS DSE DG weight (g) )

626115-0309-025 3,00 25,00 15,00 2,00 11,00 4,0626115-0309-033 3,00 33,00 23,00 2,00 11,00 4,0626115-0309-050 3,00 50,00 40,00 2,00 11,00 5,0626115-0309-058 3,00 58,00 48,00 2,00 11,00 6,0626115-0309-064 3,00 64,00 54,00 2,00 11,00 8,0626115-0109-022 1,00 22,00 13,00 5,00 1,00 0,8 11,00 4,0626115-0109-032 1,00 32,00 12,00 5,00 1,00 0,8 11,00 4,0


Styli

Straight shaft / SiN sphere


000000-1323-893 1,50 33,00 24,00 1,00 11,00 5,8000000-1323-889 2,00 33,50 24,50 1,50 11,00 6,3626115-0303-025 3,00 25,00 15,00 2,00 11,00 6,6626115-0300-033 3,00 33,00 23,00 2,00 11,00 4,4626115-0302-050 3,00 50,00 40,00 2,00 11,00 7,5626115-0300-058 3,00 58,00 48,00 2,00 11,00 8,0626115-0400-034 4,00 33,50 23,00 2,00 11,00 7,0626115-0401-064 4,00 64,00 54,00 2,50 11,00 6,0626115-0501-050 5,00 50,00 40,00 3,50 11,00 9,0626115-0501-053 5,00 53,00 40,00 3,50 11,00 9,5626115-0500-075 5,00 75,00 65,00 3,50 11,00 15626115-0601-025 6,00 25,00 15,00 2,00 11,00 6,6626115-0603-050 6,00 50,00 40,00 4,00 11,00 13626115-0800-064 8,00 63,50 50,50 6,00 11,00 27626115-0800-075 8,00 75,00 62,00 6,00 11,00 29626115-0801-100 8,00 100,00 88,00 5,00 11,00 40626115-0800-115 8,00 114,50 101,50 6,00 11,00 48626115-1000-165 10,00 165,00 150,00 6,00 11,00 52626115-1201-160 12,00 160,00 150,00 4,50 11,00 46

Styli with a silicon nitride sphere and a straight

carbide shaft are used in all standard applications.

Because of its frictional behavior it is often used as

an alternative to ruby when scanning very hard or

very soft materials.

Stepped shaft / SiN sphere


626115-0104-022 1,00 22,50 12,50 5,00 1,00 0,80 11,00 5,0626115-0103-030 1,00 30,00 19,00 10,00 2,00 0,80 11,00 7,0626115-0151-030 1,50 30,00 19,00 8,00 1,50 1,00 11,00 6,5626115-0200-032 2,00 32,00 12,00 1,50 11,00 7,0626115-0203-044 2,00 44,00 19,00 1,50 11,00 7,7626115-0204-058 2,00 58,00 48,00 33,00 4,00 1,00 11,00 8,7626115-0250-032 2,50 32,00 12,00 1,50 11,00 7,0626115-0250-044 2,50 44,00 19,00 1,50 11,00 7,8626115-0250-058 2,50 58,00 33,00 1,50 11,00 5,0

Styli with a silicon nitride sphere and a straight

carbide shaft are used in all standard applicati-

ons. SiN is an extremely hard material that can be

shaped into a very accurate sphere.




High stiffness body / ruby sphere


626115-0300-035 3,00 34,50 16,50 2,00 19,00 20600342-8124-000 8,00 114,50 92,50 6,00 19,00 59600342-8128-000 9,00 64,50 42,50 6,00 19,00 38

Styli with a ruby sphere, a high stiffness body and

a carbide shaft are used in all standard applicati-

ons, in which a maximum stiffness of the styli is

essential. Ruby is an extremely hard material, that

can be shaped into a very accurate sphere.

Reference styli


600342-8023-010 8,00 63,50 50,50 6,00 11,00 25

Reference styli M5 are marked with a red dot.

Styli


Styli with sphere / ThermoFit® shaft

The advantages of styli with the ThermoFit

CFK-Shaft are: thermal stability, minimum weight

and high stiffness, thus being ideal for long styli

and the application in a production environment.

Ruby sphere


626105-0300-025 3,00 25,00 15,00 2,00 11,00 4,0626105-0300-033 3,00 33,00 23,00 2,00 11,00 4,0626105-0300-050 3,00 50,00 40,00 2,00 11,00 4,0626105-0300-058 3,00 58,00 48,00 2,00 11,00 4,0626105-0400-033 4,00 33,00 23,00 2,00 11,00 4,0626105-0400-064 4,00 64,00 54,00 2,00 11,00 4,0626105-0510-050 5,00 50,00 40,00 3,50 11,00 4,0626105-0510-075 5,00 75,00 65,00 3,50 11,00 5,0626105-0510-100 5,00 100,00 90,00 3,50 11,00 5,0626105-0610-054 6,00 54,00 44,00 3,50 11,00 5,0626105-0710-055 7,00 55,00 45,00 3,50 11,00 5,0626105-0820-063 8,00 63,00 50,00 6,00 11,00 7,0626105-0820-075 8,00 75,00 62,00 6,00 11,00 8,0626105-0820-100 8,00 100,00 87,00 6,00 11,00 9,0626105-0820-114 8,00 114,00 101,00 6,00 11,00 10626105-0820-150 8,00 150,00 137,00 6,00 11,00 12626105-0820-200 8,00 200,00 187,00 6,00 11,00 14626105-1020-065 10,00 65,00 52,00 6,00 11,00 8,0626105-1020-118 10,00 118,00 105,00 6,00 11,00 11626105-1020-150 10,00 150,00 137,00 6,00 11,00 13626105-1020-200 10,00 200,00 187,00 6,00 11,00 15626105-1020-350 10,00 350,00 325,00 6,00 11,00 25626105-1020-500 10,00 500,00 475,00 6,00 11,00 31626105-1220-120 12,00 120,00 105,00 6,00 11,00 11626105-1220-225 12,00 225,00 200,00 6,00 11,00 28626105-1220-355 12,00 355,00 330,00 6,00 11,00 35

ThermoFit styli with minimized temperature

changing CFK shaft can be used for long styli. For

example a stylus with sphere diameter 10 mm and

length 118 mm weighs only 20% of a comparable

metal shaft. Styli are available with ruby and silicon

nitride spheres.

Styli



Silicon nitride sphere


626105-0301-025 3,00 25,00 15,00 2,00 11,00 4,0626105-0301-033 3,00 33,00 23,00 2,00 11,00 4,0626105-0301-050 3,00 50,00 40,00 2,00 11,00 4,0626105-0301-058 3,00 58,00 48,00 2,00 11,00 4,0626105-0401-033 4,00 33,00 23,00 2,00 11,00 4,0626105-0401-064 4,00 64,00 54,00 2,00 11,00 4,0626105-0511-050 5,00 50,00 40,00 3,50 11,00 4,0626105-0511-075 5,00 75,00 65,00 3,50 11,00 5,0626105-0511-100 5,00 100,00 90,00 3,50 11,00 5,0626105-0821-063 8,00 63,00 50,00 6,00 11,00 7,0626105-0821-075 8,00 75,00 62,00 6,00 11,00 8,0626105-0821-100 8,00 100,00 87,00 6,00 11,00 9,0626105-0821-114 8,00 114,00 101,00 6,00 11,00 10626105-0821-150 8,00 150,00 137,00 6,00 11,00 12626105-0821-200 8,00 200,00 187,00 6,00 11,00 14626105-1021-065 10,00 65,00 52,00 6,00 11,00 8,0626105-1021-118 10,00 118,00 105,00 6,00 11,00 11626105-1021-150 10,00 150,00 137,00 6,00 11,00 12626105-1021-200 10,00 200,00 187,00 6,00 11,00 15626105-1021-350 10,00 350,00 325,00 6,00 11,00 25626105-1021-500 10,00 500,00 475,00 6,00 11,00 31

ThermoFit styli with minimized temperature

changing CFK shaft can be used for long styli. For

example a stylus with sphere diameter 10 mm and

length 118 mm weighs only 20% of a comparable

metal shaft. Styli are available with ruby and silicon

nitride spheres.

Styli

Silicon nitrideStyli with silicon nitride spheres are an alternative

to styli with ruby spheres. Unlike ruby, silicon

nitride is polycrystalline and while not being as

hard as ruby, it has a higher preasure resistance.

This has a positive effect on its friction behaviour

when scanning very hard or very soft materials.


Styli with sphere / ceramic shaft

Styli with a ceramic shaft are light and mostly used

with probe heads with a limited load capacity, such

as touch trigger probe heads.

Ruby sphere


600342-8013-000 5,00 53,00 43,00 3,50 11,00 5,0600342-8016-000 6,00 54,00 44,00 3,50 11,00 5,0600342-8017-000 7,00 55,00 45,00 3,50 11,00 5,1600342-8014-000 8,00 63,50 50,50 6,00 11,00 8,0600342-8015-000 8,00 114,50 101,50 6,00 11,00 12600342-8018-000 9,00 64,50 51,50 6,00 11,00 9,1600342-8019-000 10,00 65,50 52,50 6,00 11,00 9,7

Styli with a ruby sphere are used in all standard

applications. Ruby is an extremely hard material

that can be shaped into a very accurate sphere.

Styli

ServiceDo you need a custom-made stylus?

Call us or send us an email.

We will be happy to assist you.


Styli

Styli without thread

Styli without thread can be used only with the

appropriate stylus mount. For example, they can

be used in star styli clamping type (see Probe Styli /

System M5 for more details).

Styli with ruby sphere

Art-Nr DK L MLE DS DSE weight (g)

600341-8450-000 0,30 15,30 2,30 1,00 0,20 1,0600341-8451-000 0,50 15,50 2,50 1,00 0,30 1,0600341-8452-000 0,60 15,60 4,60 1,00 0,40 1,0600341-8453-000 0,80 15,80 4,80 1,00 0,60 1,0600341-8454-000 1,00 16,00 5,00 1,00 0,80 1,0600341-8500-000 1,35 26,35 1,00 1,0600341-8501-000 1,50 26,50 1,00 1,0600341-8502-000 2,00 27,00 1,50 1,0600341-8503-000 2,50 27,50 1,50 1,0600341-8510-000 3,00 38,00 2,00 1,6600341-8511-000 5,00 45,00 3,50 5,8

Accessories

600341-8368-000 holder for stylus, quintuple626115-5000-199 holder for stylus, quintuple600341-8160-000 holder for stylus, single600341-8367-000 holder for stylus, quintuple

Styli with a ruby sphere and a straight carbide

shaft are used in all standard applications. Ruby is

an extremely hard material that can be shaped into

a very accurate sphere.

Stylus holder for 5 styli

Art-Nr L DS DG weight (g)

600341-8367-000 10,00 1,00 11,00 3,0600341-8368-000 10,00 1,50 11,00 3,0626115-5000-199 10,00 2,00 11,00 3,0

Styli without thread can be clamped into this five-

fold stylus holder, thus a basic star stylus with 5

coordinate directions can be assembled.


Styli

Special styli

Star styli

Art-Nr DK L ML DS B DG weight (g)

600331-8093-000 5,00 98,00 28,00 3,50 80,00 19,00 70

Star styli are suited for a multitude of different

measurement jobs in various coordinate directions.

Star styli with cube

Art-Nr DK L ML MLE DS DSE B weight (g)

602030-9025-000 1,50 45,00 15,00 6,50 2,00 1,00 15,00 18602030-9027-000 2,50 45,00 15,00 8,00 2,00 1,50 15,00 18

Star styli with cube are suited for a multitude of

different measurement jobs in various coordinate

directions.

The following contains styli for unique applications

like completely assembled star or pointer styli. Are

you looking for styli in accordance to your speci-

fications? Then don’t hesitate to call us or send us

your drawing.

Conical styli


602030-9019-000 1,00 55,00 4,00 0,80 11,00 12602030-9020-000 1,50 55,00 5,00 1,00 11,00 11602030-9021-000 2,00 55,00 5,00 1,50 11,00 11602030-9023-000 3,50 55,00 10,00 2,50 11,00 11

Conical styli are used in applications where an

extremely stiff stylus shaft is needed.


Styli

Hollow hemisphere

Art-Nr DK L DS B DG weight (g)

626105-1696-020 16,00 20,00 4,00 10,00 11,00 10626105-2296-025 22,00 23,00 4,00 14,50 11,00 13626105-3096-025 30,00 25,00 4,00 18,00 11,00 17

By applying large spheres, flaws in rough surfaces

can be evened out. Ceramic hollow-hemispheres

are ideal for measurements where low weight is

required.

Styli without shaft

Art-Nr DK L DS DG weight (g)

000000-1294-772 15,00 28,00 5,00 11,00 19

626115-1600-028 16,00 28,00 5,00 11,00 20626115-1800-028 18,00 28,00 5,00 11,00 22626115-2000-033 20,00 33,00 5,00 11,00 28626115-3000-043 30,00 43,00 5,00 11,00 67

These styli with sphere can be directly attached to

11 mm diameter extensions. Thus long styli can be

assembled e.g. for deep holes.

Conical shaft styliConical shaft styli are used if high stiffness is

needed and the workpiece is easily accessible.

Pointer styli

Art-Nr L ML DS DG weight (g)

600342-8051-000 61,00 39,00 3,50 11,00 12,00

Pointer styli have been designed for the gauging of

thread forms, marked points and lines.


Styli

Steel disc DS M5

Art-Nr DK DS B weight (g)

602030-0003-000 10,00 5,00 4,00 2,0602030-0004-000 15,00 5,00 4,00 5,0602030-0005-000 20,00 5,00 4,00 9,0602030-0006-000 30,00 5,00 4,00 21602030-0007-000 40,00 5,00 5,00 42602030-0008-000 50,00 5,00 5,00 64602030-0009-000 60,00 5,00 5,00 89

Via a clamping screw, steel discs can be attached

to an extension to generate a disc stylus. Discs

with M5 thread (DS M5) can be mounted directly

on an extension with threaded pin.

Steel disc DS 8

Art-Nr DK DS B weight (g)

602030-0010-000 15,00 8,00 4,00 4,0600341-0200-000 20,00 8,00 2,00 4,0602030-0011-000 20,00 8,00 4,00 8,0600341-0203-000 30,00 8,00 4,00 10600341-0204-000 40,00 8,00 4,00 21600341-0205-000 50,00 8,00 5,00 36600341-0206-000 60,00 8,00 6,00 59

Accessories

600341-0210-000 screw for stylus disc, M5600341-0211-000 screw for stylus disc, M5600341-0212-000 screw for stylus disc, M5

Discs with center hole (DS 8) can be mounted on

an extension using a special screw.

Steel disc styli

Art-Nr DK L B DG weight (g)

600341-8090-000 10,00 21,50 1,50 7,00 3,0600341-8095-000 15,00 21,50 1,50 10,00 6,0000000-1165-629 15,00 40,00 1,00 7,00 5,0602030-8091-000 20,00 60,00 1,00 7,00 8,0

Disc styli are already built with an integrated shaft.

They can be mounted directly to a stylus system.

The disc is made of hardened steel or ceramics.


Styli

Swiveling styli

Via a clamping mechanism, swiveling styli can be

adjusted to a specific angle position, thus making

bevelled holes measurable.

Styli with ruby sphere

Art-Nr DK L ML MLE DS DSE weight (g)

600341-8183-000 1,00 17,50 13,50 5,00 1,00 0,80 1,0600341-8185-000 2,00 28,50 24,50 1,50 1,0

Accessories

600341-8180-000 holder for stylus, single, swiveling 110 deg

The swiveling stylus is inserted into the appropriate

swiveling holder and clamped. The shaft is made

out of carbide, the sphere is made out of ruby.

Swiveling styli holder

Art-Nr L ML B DG weight (g)

600341-8180-000 40,00 22,00 6,00 11,00 15

Accessories

600341-8185-000 stylus without thread, swiveling 110 deg600341-8183-000 stylus without thread, swiveling 110 deg

The swiveling styli holder has been designed to

hold specially designated swiveling styli, that can

be attached to it by a simple insertion and

clamping process.

Disc styliDisc styli are used for measuring shoulders and

diameters inside holes that are not accessible for

star styli. Disc styli are segments of a sphere, which

are available in various diameters, materials and

thicknesses.


Carbide pins

Art-Nr Description

600341-0520-000 tungsten carbide pin for star stylus, L10, DS1600341-0521-000 tungsten carbide pin for star stylus, L10, DS1,5600341-0522-000 tungsten carbide pin for star stylus, L18, DS2600341-0523-000 tungsten carbide pin for star stylus, L18, DS3,5

Tungsten carbide pins are a part of the

customisable star styli clamping type.

Styli

Star styli clamping type

With the components in this section you can built

your own customised star stylus. Screws and styli

with long threads are used to fasten styli without

thread between slotted discs and the clamping

discs. For these star styli, we offer assembly tools

to support assembly.

Styli with thread


600342-8250-000 0,30 21,80 12,80 2,30 1,00 0,20 11,00 6,0600342-8251-000 0,50 22,00 13,00 2,50 1,00 0,30 11,00 6,0600342-8252-000 0,60 22,10 13,10 4,60 1,00 0,40 11,00 6,0600342-8253-000 0,80 22,30 13,30 4,80 1,00 0,60 11,00 6,0600342-8254-000 1,00 22,50 13,50 5,00 1,00 0,80 11,00 6,0600342-8200-000 1,35 32,85 23,85 1,00 11,00 6,0600342-8201-000 1,50 33,00 24,00 1,00 11,00 7,0600342-8202-000 2,00 33,50 24,50 1,50 11,00 7,0600342-8203-000 2,50 34,00 25,00 1,50 11,00 7,0600342-8221-000 3,00 34,50 16,50 2,00 19,00 20600342-8222-000 5,00 43,50 25,50 3,50 19,00 23

Carbide shaft; ruby sphere; thread M5x12.5. These

styli have exclusively been designed for the use

with slotted discs and clamping discs. They can be

mounted directly to an extension.


Clamping discs

Art-Nr Description weight (g)

600341-0140-000 clamp disc for star stylus, DG11, DS1,5, L1,5 1,0600341-0141-000 clamp disc for star stylus, DG19, DS5,1, L1,9 4,0

The clamping disc is screwed with a slotted disc

and a long-threaded stylus towards an extension.

In between styli without thread and tungsten car-

bide pins can be clamped - the result being a star

stylus.

Assembly tools

Art-Nr Description

600341-8300-000 assembly tool for star stylus DG11600341-8301-000 assembly tool for star stylus DG19

With this assembly tool, star styli (clamping type)

can be adjusted and assembled.

Styli

Slotted discs


600341-0150-000 slotted disc for star stylus, DG11, DS5,1, L2, DK1/1,5 1,0600341-0151-000 slotted disc for star stylus, DG19, DS5,1, L4, DK2/3,5 7,0

With the slotted discs, styli and carbide pins can be

inserted and positioned. The slotted disc is screwed

towards an extension with a clamping disc and a

long threaded stylus - the result being a star stylus.


developed by ZEISS produces outstanding results

even under difficult shop floor conditions.

ThermoFit stylus extensions have proven themselves

a thousand times worldwide – in measuring labs

and on the shop floor.

ThermoFit stylus extensions are thermally stable

and keep their length even with fluctuating tempe-

ratures.

Unlike traditional carbon-fiber extensions, thermal

torsion has nearly no effect.

Aluminum and titanium extensions are used for

lower performance requirements. Aluminum is very

light, while titanium has a lower thermal linear

expansion with higher stiffness at a relatively low

weight.

Choose from our extensive standard range. We will

also manufacture custom-made extensions with

lengths based on your specifications.

Contact us and we will gladly help you optimize

your applications.

Stylus Extensions

Measuring difficult-to-access areas

Stylus extensions are screwed directly to the cube

or adapter plate. They enable the assembly of long

styli and large styli systems to measure difficult-

to-access features on a workpiece. The range

requirements are based on the permissible weight,

stiffness and thermal stability.

If the accessibility allows it, we advise you to use

stylus extensions with a diameter as large as

possible, because bending stiffness increases with

the diameter.

To achieve optimal and reproducible measuring

results, it is inevitable to use extremely light and

thermally stable stylus extensions. Therefore, the

material used for very long stylus extensions is a

key factor.

Our unique ThermoFit stylus extensions consist of

highly stiff titanium end caps and thermally stable

carbon-fiber tubes. These tubes are manufactured

on our own machines by using a specially deve-

loped winding technology. This combination of

materials and the gluing-/cutting technology


Stylus Extensions

ThermoFit® Silver

ThermoFit silver stylus extensions can be used for

temperature stable and light configurations.

Delivery in standard lengths from stock. Special

lengths on demand.

Diameter 11

Art-Nr LE DGE weight (g)

626107-1040-100 40,00 11,00 9,0626107-1050-100 50,00 11,00 10626107-1060-100 60,00 11,00 11626107-1070-100 70,00 11,00 11626107-1075-100 75,00 11,00 12626107-1080-100 80,00 11,00 12626107-1090-100 90,00 11,00 13626107-1100-100 100,00 11,00 14626107-1120-100 120,00 11,00 15626107-1150-100 150,00 11,00 17626107-1180-100 180,00 11,00 19626107-1200-100 200,00 11,00 21626107-1250-100 250,00 11,00 24626107-1300-100 300,00 11,00 27626107-1400-100 400,00 11,00 34

Stylus extensions with diameter 11 mm are mainly

used to measure hard-to-reach characteristics of a

workpiece.

ThermoFit® SilverThermoFit Silver extension are very light, extremely

stiff and characterized by their optimal thermal

stability. For measuring tasks in the shop floor

environment, there is no alternative to ThermoFit

Silver!


Diameter 20


626107-2040-100 40,00 20,00 26626107-2050-100 50,00 20,00 28626107-2060-100 60,00 20,00 29626107-2070-100 70,00 20,00 30626107-2075-100 75,00 20,00 31626107-2080-100 80,00 20,00 32626107-2090-100 90,00 20,00 33626107-2100-100 100,00 20,00 34626107-2120-100 120,00 20,00 37626107-2150-100 150,00 20,00 41626107-2180-100 180,00 20,00 45626107-2200-100 200,00 20,00 48626107-2250-100 250,00 20,00 55626107-2300-100 300,00 20,00 62626107-2400-100 400,00 20,00 75626107-2500-100 500,00 20,00 89626107-2600-100 600,00 20,00 103

Stylus extensions with a diameter 20 mm are

mainly mounted directly to the probe head. This

ensures a higher stiffness.

Stylus Extensions


Stylus Extensions

Corresponding connection elements with cone adapter

Diameter 11 with cone receiver

For a detailed description of the accessories for

extensions with a cone receiver, see the ThermoFit

Pro section (connection elements with cone

adapter, pages 47 and 48).

This 11mm diameter ThermoFit Silver stylus exten-

sion has the usual M5 thread on one end and

a cone receiver on the other. The cone receiver

allows the insertion of various rotary, angle, and

star units (available separately) using a cone adap-

ter. This reduces the number of individual parts to

be mounted and is also cost-effective.

ThermoFit® Silver with cone receiver


626107-1050-105 50,00 11,00 13626107-1060-105 60,00 11,00 14626107-1070-105 70,00 11,00 15626107-1080-105 80,00 11,00 15626107-1090-105 90,00 11,00 16626107-1100-105 100,00 11,00 17626107-1110-105 110,00 11,00 18626107-1130-105 130,00 11,00 19626107-1160-105 160,00 11,00 21626107-1190-105 190,00 11,00 24626107-1210-105 210,00 11,00 25626107-1260-105 260,00 11,00 29626107-1310-105 310,00 11,00 33626107-1410-105 410,00 11,00 40

NEW!


Aluminum

Stylus extensions made of aluminum are light and

inexpensive. They can be used in a variety of stan-

dard applications, especially in an enviroment with

constant temperature.

Diameter 11


600341-8261-000 40,00 11,00 10600341-8262-000 60,00 11,00 14600341-8263-000 80,00 11,00 19600341-8264-000 100,00 11,00 24600341-8265-000 120,00 11,00 30



workpiece.

Diameter 20


600341-8425-000 40,00 20,00 32600341-8424-000 60,00 20,00 37600341-8423-000 80,00 20,00 43600341-8422-000 100,00 20,00 50600341-8421-000 150,00 20,00 68

600341-8420-000 200,00 20,00 85


mainly mounted directly to the probe head. This


Stylus Extensions


Titanium

The advantage of titanium extensions compared to

aluminum extensions is that they have a

higher stiffness. They are used in many standard

applications at a slightly higher weight.

Diameter 11


602030-9044-000 10,00 11,00 4,0602030-9045-000 15,00 11,00 6,0602030-9046-000 20,00 11,00 7,0602030-9047-000 25,00 11,00 9,0000000-1251-674 30,00 11,00 12602030-9049-000 40,00 11,00 14602030-9051-000 50,00 11,00 15602030-9053-000 60,00 11,00 14602030-9055-000 75,00 11,00 19602030-9057-000 80,00 11,00 19602030-9059-000 90,00 11,00 20602030-9061-000 100,00 11,00 22602030-9063-000 120,00 11,00 30602030-9065-000 150,00 11,00 29



workpiece.

Stylus Extensions


Diameter 18


626117-2010-030 10,00 18,00 10626117-2015-030 15,00 18,00 16602030-9048-000 25,00 18,00 26602030-9050-000 40,00 18,00 43602030-9052-000 50,00 18,00 35602030-9054-000 60,00 18,00 38602030-9056-000 75,00 18,00 42602030-9058-000 80,00 18,00 41602030-9060-000 90,00 18,00 47602030-9062-000 100,00 18,00 50602030-9064-000 120,00 18,00 56602030-9066-000 150,00 18,00 68602030-9067-000 200,00 18,00 67602030-9068-000 250,00 18,00 68602030-9069-000 300,00 18,00 85


mainly mounted directly to the probe. This


Inox


600341-0250-000 10,00 11,00 6,0600341-0251-000 15,00 11,00 9,0600341-0252-000 20,00 11,00 13600341-0254-000 40,00 11,00 28600341-0256-000 60,00 11,00 42600341-0258-000 80,00 11,00 58600341-0260-000 100,00 11,00 73

Stainless steel extensions have a high stiffness and

used in many standard applications. However the

higher weight has to be taken into account.

Stylus Extensions


Intelligent Logistics

ZEISS ProbeShop

Automated styli issuance on site

The ZEISS ProbeShop makes styli in the measuring

room or the production line instantly available,

whenever they are needed. The robust and automa-

ted storage system makes sure that your coordinate

measuring machines never need to stand still, just

because someone broke the last stylus. With its

intelligent and configurable software, ProbeShop will

automatically place replacement orders directly with

us or notify your purchasing department about critical

storage levels.

Safe and monitored storage

ProbeShop provides you with a complete overview

of your styli stock and all movements therein. A

comprehensive user management with various levels

of authorization gives you complete control over all

withdrawals. Detailed reports and evaluation tables

can be generated automatically and ensure you full

cost control, by enabling you to optimize your stock

step-by-step.

Flexible logistics concept

ProbeShop facilitates a flexible logistics concept for

your coordinate measuring machine accessories that

is matched precisely to your requirements. Automa-

ted, database-supported styli issuance and storage,

consignation stock, “single source” concepts:

contact us to see how we can assist you to simplify

your supply chain.

Inquiries to:


Andreas Holowitz

Tel: +49-7365-9208-243

Fax: +49-7365-9208-29

email: [email protected]

Internet: www.probes.zeiss.com


Plate Extensions

This chapter lists various plate extensions that can

be mounted to the MT/VAST adapter plate with

the part number 600667-9611-000. The chapter

on adapter plates contains more information on

complete adapter plates with an already integrated

ThermoFit plate extension.

More productivity

through fewer interfaces

For the assembly of extremely stiff and light styli

systems, it is best to use plate extensions with

proven ThermoFit technology. The ThermoFit plate

extension is directly connected with the adapter

plate, instead of having a cube in between. This

reduces the number of connections, saves up to

25% in weight and nearly doubles the stiffness.

The higher the stiffness of the styli system, the

faster you can scan without losing accuracy. This

results in higher throughput and more productivity.

The first extension at the adapter plate is critical

for the stiffness of the styli system. Particularly this

transition was optimized for highest stiffness of the

ThermoFit plate extensions. The titanium adapter

of the plate extension is manufactured from a

single piece, optimizing the flow of forces.


Plate Extensions

ThermoFit® Silver with cube 20

Art-Nr LE MLE BE DGE weight (g)

626107-2025-110 25,00 71,50 20,00 20,00 74

626107-2040-110 40,00 86,50 20,00 20,00 76

626107-2050-110 50,00 96,50 20,00 20,00 78

626107-2060-110 60,00 106,50 20,00 20,00 80

626107-2080-110 80,00 126,50 20,00 20,00 82

626107-2100-110 100,00 146,50 20,00 20,00 84

626107-2120-110 120,00 166,50 20,00 20,00 86

626107-2150-110 150,00 196,50 20,00 20,00 91

626107-2200-110 200,00 246,50 20,00 20,00 98

Accessories

600667-9611-000 adapter plate MT/VAST with active ID-Chip, set of 2, 158g/pc



626107-2025-130 25,00 66,50 15,00 20,00 60626107-2040-130 40,00 81,50 15,00 20,00 62626107-2050-130 50,00 91,50 15,00 20,00 64626107-2060-130 60,00 101,50 15,00 20,00 66626107-2080-130 80,00 121,50 15,00 20,00 68626107-2100-130 100,00 141,50 15,00 20,00 70626107-2120-130 120,00 161,50 15,00 20,00 72626107-2150-130 150,00 191,50 15,00 20,00 77626107-2200-130 200,00 241,50 15,00 20,00 84

Accessories

600667-9611-000 adapter plate MT/VAST with active ID-Chip, set of 2, 158g/pc

Plate extensions are attached directly to the

MT/VAST adapter plate. They replace the standard

cube. The cube holds five M5 threads.

Plate extensions are attached directly to the

MT/VAST adapter plate. They replace the standard

cube. The cube holds five M5 threads.

standard cube

standard cube


Connecting Elements

With the help of our extensive product range

almost every measuring task can be mastered.

Choose from a wide range of standard products or

make use of our expertise and order custom-made

angle parts.

Do you need a special connecting piece? Do you

need an angle to measure a particular feature?

Contact us today! Our CAD design experts are glad

to help you out.

There are no limits to your creativity

Connectors enable the combination of styli and

extensions into styli systems and furthermore allow

you to measure even difficult-to-access areas on

your workpieces. Save time by combining many

styli to one styli system. Increase your productivity

today!

Cubes help you to easily build rectangular combina-

tions and star styli. Moveable elements like rotary

or knuckle joints are used to create angled stylus

systems. This enables you to easily measure slanted

features. Threaded adapters provide an interface to

use M5 with M2 or M3 styli.


Connecting Elements

Cubes

Cubes are the most common connecting elements

in styli system. We carry a multitude of various

designs for all applications.

Cubes with threaded pin

Art-Nr B MAT weight (g)

600341-8361-000 15,00 titanium 13600341-8002-000 20,00 titanium 32

The threaded pin is fixed on one side of the cube.

Cubes with cone and countersink


626115-6110-002 15,00 titanium 13

One side of the cube is eqiupped with a conical

countersink. A conical screw is delivered with the

cube.

Cubes without pin


626115-6110-001 15,00 titanium 13626115-6110-003 20,00 titanium 32602030-8363-000 15,00 aluminum 7,5602030-8362-000 20,00 aluminum 20

All six threads can be used to insert a threaded

pin or a stylus. One threaded pin is included in

the delivery.


Star cubes

Star cubes are used to create star styli systems.

They are perfectly suited for operations in gear

measurement.

6-sided block

Art-Nr B DG MAT weight (g)

626105-6010-002 20,00 34,60 aluminum 51626105-6110-001 20,00 34,60 titanium 87

This six sided block 6x60 deg. is equipped with

eight threads. It can be attached to an extension

to assemble a six sided star probe.

6-sided block 30°


626105-6110-031 15,00 34,00 titanium 47

This six sided block 6x60 in a 30° angel is

equipped with eight threads. It can be attached

to an extension to assemble a six sided star probe.

Connecting Elements


8-sided block


626105-6010-000 15,00 29,00 aluminum 23626105-6110-000 15,00 29,00 titanium 40

This eight sided block 8x45 deg. is equipped with

ten threads. It can be attached to an extension to

assemble a eight sided star probe.

8-sided block 30°


626105-6110-030 15,00 41,00 titanium 66

This eight sided block 8x45 in a 30° angel is

equipped with ten threads. It can be attached to

an extension to assemble a eight sided star probe.

Connecting Elements


Revolving elements

Rotary joints

Art-Nr L DG MAT weight (g)

602030-9095-000 30,00 18,00 titanium 43626105-6280-020 20,00 11,00 titanium 13626105-6280-030 30,00 11,00 titanium 11

Moveable elements like rotary joints are used to

assemble angled styli combinations. The angle

adjustment is done lengthwise to the main axis of

the rotary joint.

Rotary knuckle


626105-6280-040 40,00 11,00 titanium 15

Moveable elements like rotary knuckles are used to

assemble angled styli combinations.

Rotable 90° angle

Art-Nr L ML DG MAT weight (g)

626105-6280-010 30,50 25,00 11,00 titanium 9,6

With this 360 deg. rotable angle you can connect

a stylus 90° perpendicular to an extension, to

measure e.g. a bore hole on the rear side of a

work-piece. Their special form allows better

accessibility than a standard cube.

Connecting Elements


Holder for styli without thread

Styli without thread can be clamped into the M5

styli holder. In case of breakage, only the stylus

without thread has to be replaced.

Stylus holder for 5 styli

Art-Nr L DS DG weight (g)

600341-8367-000 10,00 1,00 11,00 3,0600341-8368-000 10,00 1,50 11,00 3,0626115-5000-199 10,00 2,00 11,00 3,0

Styli without thread can be clamped into this

five-fold styli holder, thus a basic star stylus with

5 coordinate directions can be assembled.

L-holder for styli without thread

Art-Nr L ML DS B DG weight (g)

600341-8160-000 45,00 22,00 1,50 6,00 11,00 16

Styli without thread can be clamped into this

L-holder, thus a basic hook-shaped stylus can

be assembled.

Connecting Elements


Quadruple/revolvable


626105-6280-050 25,00 11,00 titanium 12

Small styli can be build up with this quadruple

revolvable styli holder. The holder can be mounted

on a extension.

90° angle


626105-6901-001 22,50 17,00 11,00 titanium 6,0

With this 90 deg. angles you can connect a stylus

90° perpendicular to an extension, to measure e.g.

a bore hole on the rear side of a work-piece. Their

special form allows better accessibility than a

standard cube.

Angle blocks

Art-Nr B angle (deg.) weight (g)

626105-6020-015 12,00 15,00 11626105-6020-030 12,00 30,00 11626105-6020-045 12,00 45,00 11626105-6020-060 12,00 60,00 11626105-6020-075 12,00 75,00 11

In this section you can find our standard angles.

All angles from 1-90° in this design available. We

can custom manufacture almost any angle for you.

Please use our request form.

Connecting Elements


Knuckle joints


600342-9002-000 30,00 11,00 titanium 11600342-9003-000 36,00 18,00 titanium 37

Accessories

626109-9020-000 set up device kit for knuckle joints626109-0025-000 set up device for knuckle joints DG 11

Moveable elements like these knuckle joints are

used to assemble angled styli combinations. The

angle adjustment is done diagonally to the main

axis of the joint.

Screws for styli discs

Art-Nr L ML B weight (g)

600341-0212-000 17,50 10,00 7,00 7,0600341-0211-000 30,00 21,00 19,00 9,0600341-0210-000 35,00 26,00 24,00 9,0

With these screws, discs are fastened to probe

extensions to assemble disc probes.

Screws for cubes

Art-Nr L ML weight (g)

626109-0015-000 20,00 15,00 3,0626109-0016-000 25,00 20,00 3,0626109-0017-000 27,00 22,00 4,0

These screws can be screwed through a cube into

an extension, thus an angle adjustment of the

downstream component is possible. The required

length of the screw is determined by the thickness

of the cube.

Connecting Elements

Quick and easily create you own production

suited styli system with the new ThermoFit Pro

kit. Instead of multiple single components, we

now offer prealigned and exchangeable groups of

components, consisting of extensions and rotary

adapters, instead of multiple single components.

Either use angles, knuckle joints or star styli and

adjust them to the required angles. We also fasten

your adjustment for the use in production e.g. by

laser welding.

We quickly and precisely machine preassembled

angle blocks and solid angle blocks made of a high

quality titanium alloy for you. Or you can manuf-

acture the angles yourself out of our raw angle

blocks.

The online software stylus kit “Stylus System

Creator” SSC (e.g. included in Calypso Planner,

Caligo or iDA) provides all angle blocks as adju-

stable components. The design and production of

complex special angles can be highly time-consu-

ming. Shorten the start-up phase of your inspec-

tion plan by simply using the available elements.


ThermoFit® Pro

Styli systems for the production


ThermoFit® Pro

Extensions ThermoFit® Pro

ThermoFit Pro extensions can be mounted to a

ThermoFit Pro adapter plate with the help of the

distortion secure plug connection. Star styli or

special angle pieces can be attached and adjusted

to the conical interface.

Extensions 11


626107-4050-000 50,00 11,00 17626107-4060-000 60,00 11,00 17626107-4070-000 70,00 11,00 18626107-4080-000 80,00 11,00 19626107-4090-000 90,00 11,00 20626107-4100-000 100,00 11,00 20626107-4110-000 110,00 11,00 21626107-4130-000 130,00 11,00 23626107-4160-000 160,00 11,00 25626107-4190-000 190,00 11,00 27626107-4210-000 210,00 11,00 29626107-4260-000 260,00 11,00 32626107-4310-000 310,00 11,00 36626107-4410-000 410,00 11,00 44

Accessories

626107-6020-000 Angle unit with cone adapter, blank626107-6280-050 Star probe retainer with cone adapter, 1mm, titanium626107-6280-040 Knuckle element with cone adapter, titanium626107-6280-010 End angle with cone adapter, titanium626107-6280-030 Rotary unit with cone adapter, long626107-6280-020 Rotary unit with cone adapter, short626119-0001-019 Screw set for cone receiver, ThermoFit Pro, 10 pcs

This extension has a diameter of 11mm and a

ThermoFit Pro adapter. This extension is used to

measure hard-to-reach areas on your workpiece.



Extensions 20/11


626107-4165-105 165,00 105,00 11,00 20,00 47

626107-4205-105 205,00 105,00 11,00 20,00 53626107-4215-155 215,00 155,00 11,00 20,00 51626107-4255-105 255,00 105,00 11,00 20,00 60626107-4255-155 255,00 155,00 11,00 20,00 57626107-4265-065 265,00 65,00 11,00 20,00 64626107-4265-205 265,00 205,00 11,00 20,00 54626107-4275-155 275,00 155,00 11,00 20,00 60626107-4285-085 285,00 85,00 11,00 20,00 66626107-4305-105 305,00 105,00 11,00 20,00 68626107-4305-155 305,00 155,00 11,00 20,00 64626107-4305-205 305,00 205,00 11,00 20,00 60626107-4315-065 315,00 65,00 11,00 20,00 72626107-4315-255 315,00 255,00 11,00 20,00 58626107-4325-205 325,00 205,00 11,00 20,00 63626107-4335-085 335,00 85,00 11,00 20,00 73626107-4355-105 355,00 105,00 11,00 20,00 75626107-4355-155 355,00 155,00 11,00 20,00 71626107-4355-205 355,00 205,00 11,00 20,00 68626107-4355-255 355,00 255,00 11,00 20,00 64626107-4365-065 365,00 65,00 11,00 20,00 79626107-4375-255 375,00 255,00 11,00 20,00 67626107-4385-085 385,00 85,00 11,00 20,00 81626107-4405-105 405,00 105,00 11,00 20,00 82626107-4405-155 405,00 155,00 11,00 20,00 79626107-4405-205 405,00 205,00 11,00 20,00 75626107-4405-255 405,00 255,00 11,00 20,00 71626107-4465-065 465,00 65,00 11,00 20,00 94626107-4485-085 485,00 85,00 11,00 20,00 95

Accessories


The ThermoFit Pro extension 20/11 is used for

stylus systems which require a high bending resi-

stance. This extension consists out of two pieces,

one with a diameter of 11mm and one with a

diameter of 20mm. All pieces are connected by

the unique ZEISS cutting adhesive technology.

ThermoFit® Pro



Plate extensions

Plate extensions in ThermoFit technology are most

suitable for the use in assembling very stiff and

light styli systems. This reduces the number of

connections, saves up to 25% of weight and

nearly doubles the stiffness.

ThermoFit® Pro

Plate extensions with cube

Art-Nr MLE BE DGE weight (g)

626107-2025-160 88,10 20,00 20,00 99626107-2040-160 103,10 20,00 20,00 101626107-2050-160 113,10 20,00 20,00 102626107-2060-160 123,10 20,00 20,00 104626107-2080-160 143,10 20,00 20,00 107626107-2100-160 163,10 20,00 20,00 110626107-2120-160 183,10 30,00 20,00 113626107-2150-160 213,10 20,00 20,00 117626107-2200-160 263,10 20,00 20,00 124

ThermoFit Pro extensions, angle pieces or

standard styli M5 can be attached to the

ThermoFit Pro plate extensions. Including fastening

screws and tool.

Plate extensions without cube

Art-Nr MLE DGE weight (g)

626107-2025-145 56,50 20,00 51626107-2040-145 71,50 20,00 54626107-2050-145 81,50 20,00 55626107-2060-145 91,50 20,00 57626107-2080-145 111,50 20,00 60626107-2100-145 131,50 20,00 62626107-2120-145 151,50 20,00 65626107-2150-145 181,50 20,00 70626107-2200-145 231,50 20,00 77

Angle pieces can be attached to ThermoFit Pro

extensions without cube. Additionally, a bar can be

directly attached to the extension. Including

fastening screws.


ThermoFit® Pro

Adapter with conical interface

Art-Nr LE DGE MAT weight (g)

626107-6060-000 25,00 11,00 titanium 13

Accessories


The adapter with conical interface is used to create

solid angle pieces which are fast and easy to adjust.

Raw sphere block, short

Art-Nr L ML MAT weight (g)

626107-6021-000 25,00 17,00 titanium 19

An angle piece can easily be created by machining

the raw sphere block.

Solid angle piece, short

Fully worked angle pieces are available on

request/order.

Art-Nr L ML MAT W

626107-6021-xxx 25,00 17,00 titanium on request


ThermoFit® Pro

Raw sphere block, long

Art-Nr L ML MAT weight (g)

626107-6022-000 43,00 35,00 titanium 27

The long sphere block like the short sphere block

can be used to create a solid angle piece. The

sphere block can replace the adapter with conical

interface, because of its length.

Solid angle piece, long

Art-Nr L ML MAT W

626107-6022-xxx 43,00 35,00 titanium on request

Fully worked angle pieces are available on

request/order.

Rotary elementsOur original ZEISS rotary elements are based on

the concept of a play-free conical joint. The robust

M3 internal-thread styli with Torx joint ensure high

clamping forces. Even after repeated use, the rotary

elements can be adjusted well and hold their tracer

pins securely.


Adapter plate ThermoFit® Pro

Adapter plate with single cube


626107-2000-961 adapter Plate MT/VAST with Single Cube, ThermoFit Pro 160

Adapter plates can be mounted to a MT/VAST

probe and are equipped with a ID-chip. This chip

can be identified by the CMM. The single cube

enables unilateral ThermoFit Pro styli systems.

The adapter plate is delivered with screws, marking

clip and tools.

Adapter plate with double cube


626107-2000-962 adapter Plate MT/VAST with Double Cube, ThermoFit Pro 181

Adapter plates can be mounted to a MT/VAST

probe and are equipped with a ID-chip. This chip

can be identified by the CMM. The double cube

enables bilateral styli systems. The adapter plate is

delivered with screws, marking clip and tools.

ThermoFit® Pro


ThermoFit® Pro with double cube

Art-Nr MLE BE DGE weight (g)

626107-2025-960 88,10 20,00 20,00 211626107-2040-960 103,10 20,00 20,00 213626107-2050-960 113,10 20,00 20,00 214626107-2060-960 123,10 20,00 20,00 216626107-2080-960 143,10 20,00 20,00 219626107-2100-960 163,10 20,00 20,00 222626107-2120-960 183,10 20,00 20,00 225626107-2150-960 213,10 20,00 20,00 229626107-2200-960 263,10 20,00 20,00 236

Accessories

626109-0037-000 hex wrench, 4mm, L350

Adapter plate with ThermoFit Pro plate extension

and double cube. Including fastening screws, mar-

king clip and tool.

ThermoFit® Pro without cube

Art-Nr MLE DGE weight (g)

626107-2025-945 56,50 20,00 163626107-2040-945 71,50 20,00 166626107-2050-945 81,50 20,00 167626107-2060-945 91,50 20,00 169626107-2080-945 111,50 20,00 172626107-2100-945 131,50 20,00 174626107-2120-945 151,50 20,00 177626107-2150-945 181,50 20,00 182626107-2200-945 231,50 20,00 189

Accessories

626109-0037-000 hex wrench, 4mm, L350

Angle pieces can be attached to ThermoFit Pro

extensions without cube. Additionally, a bar can be

directly attached to the extension. Including faste-

ning screws.

ThermoFit® Pro


Connection elements with conical interface

End angle

Art-Nr L ML B DG MAT weight (g)

626107-6280-010 15,50 10,00 5,50 11,00 titanium 4,7

End angles allow to bend a stylus at the end of

an extension in a 90° angle, e.g. to measure a

bore hole on the bottom side of a workpiece. The

special design enables a better accessibility than a

standard cube. The end angle can be mounted and

adjusted to a conical interface.

ThermoFit® Pro

Knuckle joints


626107-6280-040 19,00 11,00 titanium 11

The knuckle joint can be directly mounted to a

conical interface and any solid angle piece can be

attached to the knuckle joint.

Raw angle block


626107-6020-000 16,00 10,00 11,00 titanium 4,5

Angle pieces can be created out of angle blocks

fast and easily and can be mounted to conical

interfaces.

Machined angle piece

Art-Nr L ML DG MAT W

626107-6020-xxx 16,00 10,00 11,00 titanium on request

We machine angle pieces out of our raw blocks for

you. Please use the request form on the last pages

of this catalogue.


ThermoFit® Pro

Star stylus 1mm

Art-Nr L DS DG MAT weight (g)

626107-6280-050 10,00 1,00 11,00 titanium 4,1

Create small star styli with the star stylus piece.

Clamp the stylus without thread into the adapter.

Mount and adjust the star stylus to the conical

interface. A standard stylus can be attached

additionally to the M5 thread.

Short rotary piece

The rotary piece is mounted to a conical interface

and any M5 component can be attached to the

rotary piece.


626107-6280-020 5,00 11,00 titanium 2,5

Long rotary piece


626107-6280-030 15,00 11,00 titanium 6,9

The rotary piece is mounted to a conical interface

and any M5 component can be attached to the

rotary piece.

Star adapter M3 XXT


626107-6280-060 10,00 5,00 11,00 titanium 5,0

Up to five M3 XXT styli can be mounted to the

star adapter. This makes versatile and extreme

small star styli possible.


ThermoFit® Pro

Multiple holders

Multiple holders allow the creation of complex styli

systems in ThermoFit Pro design.

Fivefold holder

Art-Nr L B MAT weight (g)

626107-6060-005 104,00 20,00 titanium 124

Accessories

626107-6060-006 screw with female thread for cube, ThermoFit Pro, V2A626107-6060-002 screw for cubes, ThermoFit Pro, V2A

Extensions and angle pieces can be attached to the

bar in an exact angular position. The fivefold

holder contains 20 connection points. Five screws

and tools included.

Threefold holder

Art-Nr L B MAT weight (g)

626107-6060-003 64,00 20,00 titanium 76

Accessories

626107-6060-006 screw with female thread for cube, ThermoFit Pro, V2A626107-6060-002 screw for cubes, ThermoFit Pro, V2A

Extensions and angle pieces can be attached to

the bar in an exact angular position. The threefold

holder contains 12 connection points. Three screws

and tools included.


ThermoFit® Pro

Screws for cubes

Screw with female thread for cube

Screw set for cone retainer

Art-Nr L ML weight (g)

626107-6060-001 15,00 10,00 3,7626107-6060-002 30,00 25,00 5,2626119-0001-018 30,00 25,00 screw set, 10 pcs

Art-Nr Description

626119-0001-019 Screw set for cone retainer, ThermoFit Pro, 10 pcs

Screws are used to mount extensions to ThermoFit

Pro cubes.

Screws are used to mount extensions to ThermoFit

Pro cubes.

This spare parts kit comprises ten M3 Torx screws to be used to secure conical connections.

Index disc


626107-6060-004 5,00 20,00 titanium 6,6

Index discs are used to mount the threefold and

fivefold holders to the adapter plates with cube.

Art-Nr L ML B weight (g)

626107-6060-006 30,00 25,00 10,00 27

Accessories


Styli Kits M5

All individual parts of the styli kits are available

from stock. Place your orders online at our web

shop www.probes.zeiss.com

The perfect start

Styli kits are the ideal initial equipment for your

coordinate measuring machine. Inspired by our

own experience – designed to enhance your

measuring experience: our styli kits contain a

variety of carefully selected components for the

assembly of styli systems.

We provide well-matched and extensive kits to

measure large and small workpieces. Inside the

kits you can also find special tools and adjusting

devices to ensure a fast and reliable setup.


Styli Kits M5

Styli kit, M5, MT/VAST for small workpieces

Art-Nr Description

626115-9030-000 styli kit, M5, MT/VAST for small workpieces, set of 29 pcs.

Content Qty Description

602030-8060-000 1 stylus with thread, shouldered, HM, ruby, DK0,8, L32

602030-8061-000 1 stylus with thread, shouldered, HM, ruby, DK1, L32

602030-8064-000 1 stylus with thread, shouldered, HM, ruby, DK1,5, L32

602030-8067-000 2 stylus with thread, shouldered, HM, ruby, DK2, L44

600341-8452-000 1 stylus without thread, HM, ruby, DK0,6, L15,6


600341-8451-000 3 stylus without thread, HM, ruby, DK0,5, L15

600341-8454-000 3 stylus without thread, HM, ruby, DK1, L16


600341-8502-000 1 stylus without thread, HM, ruby, DK2, L27


600342-9002-000 1 knuckle joint, titanium

602030-9025-000 1 star stylus with cube, B15, DK1,5, ML15

600341-8262-000 1 stylus extension, aluminium, DGE11, L60

600341-8264-000 1 stylus extension, aluminium, DGE11, L100

602030-0021-000 1 hex wrench DIN 911, SW2,5

600341-8361-000 1 cube, titanium, B15

600341-8367-000 1 holder for stylus, quintuple 1,0

600341-8368-000 1 holder for stylus, quintuple, 1,5

600341-8596-000 1 set of 2 pin wrenches, 2,9

626109-0022-000 1 tweezer

Styli kit, M5, MT/VAST for small workpieces, set of

29 pcs.


Styli kit, M5, MT/VAST, for large workpieces

Art-Nr Description

626115-9031-000 styli kit, M5, MT/VAST, for large workpieces,set of 34 pcs.

Content Qty

600342-8020-000 2 stylus with thread, HM, ruby, DK3, L33,5600342-8021-000 2 stylus with thread, HM, ruby, DK3, L58600342-8022-000 2 stylus with thread, HM, ruby, DK5, L53600342-8023-000 1 stylus with thread, HM, ruby, DK8, L63,5

600342-8124-000 1 stylus with thread, HM, ruby, DK8, L114,5600342-8024-000 1 stylus with thread, HM, ruby, DK8, L114,5600341-8261-000 2 stylus extension, aluminium, DGE11, L40600341-8262-000 2 stylus extension, aluminium, DGE11, L60600341-8264-000 2 stylus extension, aluminium, DGE11, L100600341-8425-000 2 stylus extension, aluminium, DGE20, L40600341-8424-000 1 stylus extension, aluminium, DGE20, L60600341-8422-000 2 stylus extension, aluminium, DGE20, L100600341-8420-000 1 stylus extension, aluminium, DGE20, L200600341-0206-000 1 stylus disc, DK60600341-0203-000 1 stylus disc, DK30600341-8090-000 1 ball disc stylus with thread, DK 10, L21,5600341-0252-000 2 stylus extension, V2A, DGE11, L20600341-0210-000 2 screw for stylus disc600341-0212-000 2 screw for stylus disc600341-8002-000 2 cube, titanium, B20600342-9003-000 1 knuckle joint, titanium600341-8595-000 1 tool set

Styli kit, M5, MT/VAST, for large workpieces, set of

34 pcs.

Styli Kits M5


Styli Kits M5

Styli kit, M5, ST/ST3, small

Art-Nr Description

626115-9021-000 styli kit, M5, ST/ST3, small, set of 19 pcs.


602030-9011-000 1 stylus with thread, HM, ruby, DK3, L50600342-8024-000 1 stylus with thread, HM, ruby, DK8, L114,5600342-8020-000 3 stylus with thread, HM, ruby, DK3, L33,5600342-8022-000 2 stylus with thread, HM, ruby, DK5, L53600342-8023-000 1 stylus with thread, HM, ruby, DK8, L63,5600341-8265-000 2 stylus extension, aluminium, DGE11, L120600341-8262-000 4 stylus extension, aluminium, DGE11, L60600341-8596-000 1 set of 2 pin wrenches, 2,9600341-0211-000 1 screw for stylus disc600341-0221-000 1 screw for cube600341-8361-000 2 cube, titanium, B15

Styli kit, M5, ST/ST3, small set of 19 pcs.

Extension kit, M5, ThermoFit® Silver, diameter 11 m

Art-Nr Description

626107-9013-100 extension kit, M5, ThermoFit silver


626107-1050-100 2 stylus extension, ThermoFit silver, DGE11, L50626107-1100-100 3 stylus extension, ThermoFit silver, DGE11, L100626107-1150-100 2 stylus extension, ThermoFit silver, DGE11, L150626107-1200-100 2 stylus extension, ThermoFit silver, DGE11, L200000000-0015-328 2 pin wrench, 2,9

Extension kit, M5, ThermoFit silver, diameter 11

mm, 11 pcs. ThermoFit silver stylus extensions

reacts very stable on temperature fluctuations.

Thereby you receive a good repeatability even on

the shop floor. ThermoFit extensions are optimized

for the use with VAST scanning technologie from

Carl Zeiss.


Extension kit, M5, ThermoFit® Silver, diameter 20 m

Art-Nr Description

626107-9014-100 extension kit, M5, ThermoFit silver


626107-2300-100 2 stylus extension, ThermoFit silver, DGE20, L300626107-2200-100 4 stylus extension, ThermoFit silver, DGE20, L200626107-2150-100 3 stylus extension, ThermoFit silver, DGE20, L150

626107-2100-100 3 stylus extension, ThermoFit silver, DGE20, L100000000-0015-328 2 pin wrench, 2,9

Extension kit, M5, ThermoFit silver, diameter 20

mm 14 pcs. ThermoFit silver stylus extensions

reacts very stable on temperature fluctuations.

Thereby you receive a good repeatability even on

the shop floor. ThermoFit extensions are optimized

for the use with VAST scanning technologie from

Carl Zeiss.

Styli Kits M5

Styli kit, M5, ST/ST3, standard

Art-Nr Description

626115-9020-000 styli kit, M5, ST/ST3, standard, set of 38 pcs.


600342-8020-000 4 stylus with thread, HM, ruby, DK3, L33,5600342-8021-000 2 stylus with thread, HM, ruby, DK3, L58600342-8015-000 1 stylus with thread, HM, ruby, DK3, L114,5602030-9013-000 2 stylus with thread, HM, ruby, DK5, L50600342-8023-000 2 stylus with thread, HM, ruby, DK8, L63,5600342-8024-000 1 stylus with thread, HM, ruby, DK8, L114,5600341-8261-000 2 stylus extension, aluminium, DGE11, L40600341-8262-000 6 stylus extension, aluminium, DGE11, L60600341-8264-000 1 stylus extension, aluminium, DGE11, L100600341-8265-000 2 stylus extension, aluminium, DGE11, L120626107-1200-100 2 stylus extension, ThermoFit silver, DGE11, L200602030-8091-000 1 disc stylus with thread, DK20, L60600341-8095-000 1 ball disc stylus with thread, DK15, L21,5000000-1165-629 1 ball disc stylus with thread, DK15, L40600341-0221-000 2 srew for cube600341-8361-000 4 cube, titanium, B15600342-9002-000 2 knuckle joint, titanium602030-0021-000 1 hex wrench DIN 911, SW2,5600341-8596-000 1 set of 2 pin wrenches, 2,9

Styli kit, M5, ST/ST3, standard, set of 38 pcs.


Styli and extension Kit M5, ThermoFit® Silver, small

Art-Nr Description

626107-9011-000 styli and extension kit, M5, ThermoFit silver


626107-1060-100 1 stylus extension, ThermoFit silver, DGE11, L60626107-1080-100 1 stylus extension, ThermoFit silver, DGE11, L80626107-1120-100 1 stylus extension, ThermoFit silver, DGE11, L120626107-2060-100 1 stylus extension, ThermoFit silver, DGE20, L60626107-2080-100 1 stylus extension, ThermoFit silver, DGE20, L80626107-2180-100 1 stylus extension, ThermoFit silver, DGE20, L180626105-0301-033 2 stylus with thread, ThermoFit, SiN, DK3, L33 626105-0511-075 1 stylus with thread, ThermoFit, SiN, DK5, L75626105-0821-114 1 stylus with thread, ThermoFit, SiN, DK8, L114602030-8064-000 1 stylus with thread, shouldered, HM, ruby, DK1,5, L32602030-8066-000 1 stylus with thread, shouldered, HM, ruby, DK2, L32626107-2050-110 1 plate extension, ThermoFit silver, DGE20, L50, cube, B20000000-0015-247 1 hex wrench DIN 911, SW3000000-0015-248 1 hex wrench DIN 911, SW4626109-0016-000 1 screw for cube, V2A, L25, ML20

626109-0015-000 1 screw for cube, V2A, L20, ML 15626109-0017-000 1 screw for cube, V2A600341-8361-000 2 cube, titanium, B15626109-0012-000 2 hook wrench DG11626109-0013-000 2 hook wrench DG20626105-6280-020 1 rotary joint DG11, L20

Styli and extension kit M5, ThermoFit silver, small

set of 25 pcs.

Styli Kits M5


Styli and extension kit M5, ThermoFit® Silver, large

Art-Nr Description

626107-9010-000 styli and extension kit, M5, ThermoFit silver


626105-0301-058 3 stylus with thread, ThermoFit, SiN, DK3, L58626105-0511-050 3 stylus with thread, ThermoFit, SiN, DK5, L50626105-0511-075 3 stylus with thread, ThermoFit, SiN, DK5, L75 626105-0821-114 2 stylus with thread, ThermoFit, SiN, DK8, L114626105-0821-150 2 stylus with thread, ThermoFit, SiN, DK8, L150626105-1021-200 1 stylus with thread, ThermoFit, SiN, DK10, L200626107-1040-100 2 stylus extension, ThermoFit silver, DGE11, L40626107-1050-100 2 stylus extension, ThermoFit silver, DGE11, L50626107-1060-100 2 stylus extension, ThermoFit silver, DGE11, L60626107-1080-100 2 stylus extension, ThermoFit silver, DGE11, L80626107-1100-100 2 stylus extension, ThermoFit silver, DGE11, L100626107-2050-100 1 stylus extension, ThermoFit silver, DGE20, L50626107-2080-100 1 stylus extension, ThermoFit silver, DGE20, L80626107-2100-100 1 stylus extension, ThermoFit silver, DGE20, L100626107-2150-100 1 stylus extension, ThermoFit silver, DGE20, L150626107-2200-100 1 stylus extension, ThermoFit silver, DGE20, L200 626107-2300-100 1 stylus extension, ThermoFit silver, DGE20, L300626107-2100-110 1 plate extension, ThermoFit silver, DGE20, L50, cube B20626107-2050-110 2 plate extension, ThermoFit silver, DGE20, L50, cube B20600341-8002-000 2 cube, titanium, B20600341-8361-000 4 cube, titanium, B15626105-6280-020 2 rotary joint DG11, L20600342-9002-000 2 knuckle joint, titanium, DG11, L29626109-0015-000 1 screw for cube, V2A, L20, ML15626109-0016-000 1 screw for cube, V2A, L25, ML20626109-0017-000 1 screw for cube, V2A, L27, ML22626109-9010-000 1 tool kit

Styli and extension kit M5, ThermoFit, large set of

47 pcs.

Styli Kits M5


Styli Kits M5

Styli kit, M5, MT/VAST, gear measurement

Art-Nr Description

626115-9040-000 styli kit, M5, MT/VAST, for gear tooth measurement, 35 pc.


600341-0250-000 2 stylus extension, V2A, DGE11, L10600341-0251-000 2 stylus extension, V2A, DGE11, L15600341-0252-000 1 stylus extension, V2A, DGE11, L20600341-0254-000 1 stylus extension, V2A, DGE11, L40600341-0258-000 1 stylus extension, V2A, DGE11, L80600341-8454-000 2 stylus without thread, HM, ruby, DG1, L16600341-8501-000 1 stylus without thread, HM, ruby, DG1,5, L26,5600341-8503-000 1 stylus without thread, HM, ruby, DG2,5, L27,5600341-8510-000 1 stylus without thread, HM, ruby, DG3, L38600341-8511-000 1 stylus without thread, HM, ruby, DG5, L45600342-8020-000 1 stylus with thread, HM, ruby, DG3, L33,5600342-8025-000 1 stylus with thread, HM, ruby, DG4, L27600342-8013-000 1 stylus with thread, ceramic, ruby, DG5, L53600342-8016-000 1 stylus with thread, ceramic, ruby, DG6, L54600342-8017-000 1 stylus with thread, ceramic, ruby, DG7, L55,5600342-8014-000 1 stylus with thread, ceramic, ruby, DG8, L63,5600342-8018-000 1 stylus with thread, ceramic, ruby, DG9, L64,5600342-8019-000 1 stylus with thread, ceramic, ruby, DG10, L65,5600341-8367-000 4 holder for stylus, quintuple, 1,0600341-8368-000 4 holder for stylus, quintuple, 1,5602030-0222-000 1 pin wrench, 2,9602030-0027-000 1 pin wrench,1,7626109-0022-000 1 tweezer

Styli kit, M5, MT/VAST for gear measurement, set

of 35 pcs.


Adapter Plates

Original Carl Zeiss adapter plates for MT/VAST

probes are manufactured exclusively by Carl Zeiss

in Germany. The quality is continually monitored

in accordance with our strict and thorough review

process. Take advantage of our expertise.

Adapter plates are available for all applications:

standard adapter plates, adapter plates with

multiple styli holder for gear measurement and

adapter plates with ThermoFit stylus extensions

for the shop floor. Choose from our wide range of

products.

Don't compromise!

Your coordinate measuring machine from Carl Zeiss

is a highly accurate system in which all components

have been precisely adjusted. Small deviations from

the quality requirements of the integrated compo-

nents, such as those that can occur with non-ZEISS

components, may have a considerable impact on

the measuring uncertainty of the entire coordinate

measuring machine.

And the adapter plate is located at a critical

position between the CMM and your workpiece!


Adapter Plates

Adapter plates with cube


600667-9601-000 adapter plate MT/VAST with active ID-Chip 158600667-9611-000 adapter plate MT/VAST with active ID-Chip, set of 2600667-9602-000 adapter plate MT/VAST, active ID-Chip, reference plate 158

Accessories

626109-0010-000 torque hex wrench 2 Nm, 2,5 mm600660-8365-000 probe socket MT/VAST

Adapter plates with M5 holder


626107-2000-940 adapter plate MT/VAST, M5, without cube 139

Adapter plates with extensionThe adapter plates are delivered with a completely

built-in and adjusted extension.

These adapter plates can be attached to the

MT/VAST probe. They are equipped with

an ID-chip that is recognized by the CMM.

The reference adapter plate is marked with a

red ring.

A styli or an extension diameter 20 can be vertically

mounted to these adapter plates. Because of the

flat design they are very qualified for the utilization

of the Z measuring range.


Adapter Plates

Adapter plates with extension



626107-2025-930 25,00 66,50 15,00 20,00 167626107-2040-930 40,00 81,50 15,00 20,00 169626107-2050-930 50,00 91,50 15,00 20,00 171626107-2060-930 60,00 101,50 15,00 20,00 173626107-2080-930 80,00 121,50 15,00 20,00 175626107-2100-930 100,00 141,50 15,00 20,00 177626107-2120-930 120,00 161,50 15,00 20,00 179626107-2150-930 150,00 191,50 15,00 20,00 184



626107-2025-910 25,00 71,50 20,00 20,00 181626107-2040-910 40,00 86,50 20,00 20,00 183

626107-2050-910 50,00 96,50 20,00 20,00 185626107-2060-910 60,00 106,50 20,00 20,00 187626107-2080-910 80,00 126,50 20,00 20,00 189626107-2100-910 100,00 146,50 20,00 20,00 191626107-2120-910 120,00 166,50 20,00 20,00 193626107-2150-910 150,00 196,50 20,00 20,00 198

Adapter plates with star


626107-2070-950 70,00 110,50 29,00 20,00 200

The extension is assembled to a MT/Vast adapter

plate and already adjusted.

The extension is assembled to a MT/Vast adapter

plate and already adjusted.

This adapter plate with built-in eightfold star unit

is preferentially used for the measuring of external

teethes. The star unit has a flank pitch of 8x45°.

standard cube

standard cube

standard cube


Adapter Plates

Multiple styli holder

Multiple styli holders are basically used for the measuring of gears. Multiple styli and extensions can be

mounted to it.

Encoded MT/VAST plate with multiple styli holder


626107-2000-951 multiple styli adapter plate encoded with MT/VAST plate 425

The encoded MT/VAST plate with multiple styli

holder contains 26 M5 threads.



626107-2070-951 multiple styli adapter plate encoded with MT/VAST plate 391

This encoded MT/VAST plate with multple styli

holder has a spacer made of thermally stable

ThermoFit. The holder contains 26 M5 threads.



626107-2070-911 70,00 96,50 180,00 20,00 418

All titanium cubes are adjusted and permanently

glued. The space are made of thermally stable

ThermoFit extensions - for applications directly in

production.

standard cube


Adapter Plates

Marking clip

Marking set

Art-Nr Description

626119-0010-001 labeling clips set MT/VAST

Accessories

626119-0010-004 typewriter ribbon, white 9mm626119-0010-000 labeling clips MT/VAST (set of 10 pcs.)626119-0010-003 lettering device for labeling clips MT/VAST

Mark your styli systems and avoid errors.

Marking clips allow the labelling of MT/VAST

adapter plates. The set contains a lettering

device with ribbon and 20 clips.

Marking clips

Art-Nr Description

626119-0010-000 labeling clips MT/VAST (set of 10 pcs.)

Marking clips are made of plastic. They are directly

mounted to the adapter plate. (Delivery without

adapter plate).

The lettering device is used for printing labels for

the marking clips.

For use in lettering device 626119-0010-003.

Lettering device

Art-Nr Description

626119-0010-003 lettering device for labeling clips MT/VAST

Accessories

626119-0010-004 typewriter ribbon, white 9mm

Typewriter ribbon

Art-Nr Description

626119-0010-004 typewriter ribbon, white 9mm



VAST® gold mit Temperaturtastkopf

Temperature Sensor

Measuring the temperature directly at

the workpiece

You can connect an adapter plate with temperature

sensor to the VAST gold probe. Thus the temperature

is measured directly at the workpiece during the

automatic measuring run – without manual

intervention. This is a great time saver.


Temperature Sensor

Adapter plate for RST-T/VAST

Art-Nr Description

600667-9603-000 adapter plate for temperature probe head RST/VAST

Adapter plate for temperature probe RST/VAST.

Temperature probe

Art-Nr Description

600661-9670-000 temperature probe head RST-T/VAST "Gold" with case

Accessories

600661-8600-000 temperature sensor PT-100600661-8421-000 probe extension, RST, ThermoFit600667-9603-000 adapter plate for temperature probe head RST/VAST600661-9225-000 RST knuckle joint600661-8420-000 probe extension, RST, ThermoFit

The RST temperature probe can be mounted to a

MT/VAST adapter plate. The temperature sensor is

exchangeable.

Replacement sensor for temperature measuring

head RST-T/VAST. The sensor can easily be

removed from and inserted onto the measuring

head by hand.

Spare sensor for RST-T

Art-Nr Description

600661-8600-000 temperature sensor PT-100


Probe extensions


600661-8420-000 60,00 24,00 46600661-8421-000 100,00 24,00 56600661-8422-000 200,00 24,00 78600661-8423-000 300,00 24,00 100600661-8435-000 350,00 24,00 114

With this extension the RST probe can be fixed to

the resting swivel joint (RDS). Hard-to-reach areas

can be better accessed with the help of various

extensions. The tubes of the extensions are produ-

ced with the proven ZEISS ThermoFit technology.

Temperature Sensor

RST knuckle joint


600661-9225-000 94,00 24,00 97

With the RST knuckle joint angles between 0 and

90 degrees can be adjusted, e.g. to access features

that are difficult to reach with the RST probe.


Machine Accessories

Manual shifting table

for all coordinate measuring machines

The shifting table enables the ergonomic loading

of the jig outside the measurement volume. The

shuttle path measures 440mm. The clamping sur-

face of the shifting plate measures 620x620mm

and is equipped with M12 threaded bores in a

100x100 mm grid. The permitted maximum load

is 150kg. A built-in cable pull for feeders enables

the easy integration of temperature sensors.

Technician`s position at loading

with shifting tablewithout shifting table

Inquiries to:


Andreas Holowitz

Tel: +49.7365.9208.243

Fax: +49.7365.9208.29

email: [email protected]

Internet: www.probes.zeiss.com

The shifting plate is also compatible with the

following pallet systems:

- J&P CMB base plates up to 600 x 400mm

- 500 x 500mm interchangeable pallet systems

(626109-9220-622 and 626109-9220-652)

- Other systems available on request


Changer Racks

ProMax – make use of the entire measuring range

ProMax is an upgrade to the Multi-Sensor-Rack

(MSR). To measure complex parts 15-25 styli

systems are often needed. Whenever large and

very long stylus systems are stored in a fixed

changer rack, it makes part of the measuring range

unavailable by limiting the movement paths of the

CMM’s sensor.

The solution: ProMax automatically moves the

Multi-Sensor Rack out of the measuring range

when the styli are no longer needed. Thus you do

not have to sacrifice any of the CMM’s valuable

measuring range and are still able to measure and

move around even very large parts.

ProMax is modularly designed, making it adjustable

to nearly any coordinate measuring machine from

Carl Zeiss. For retrofits of existing coordinate

measuring machines, the existing CALYPSO

measurement plans do not have to be modified.

ProMax is a proven system: hundreds of installed

systems worldwide enable our customers to

optimally use their measuring range. Please contact

us for further details.

Productivity at its best

Changer racks increase the capabilities of your

coordinate measuring machine. Our Multi-Sensor-

Racks (MSR) store and keep all styli systems that

you need for your measurements. The styli systems

are placed in the probe sockets on the MSR.

During a measuring run, the CMM acquires a new

styli system and places the no-longer-needed

system in the rack. This makes the MSR a prerequi-

site for interruption-free measuring runs.

You can freely select the number and position

of the sensor and stylus slots. The height of the

assembly levels can be set as needed. This provides

a high degree of flexibility and you can optimally

adapt the MSR to your requirements. Use our MSR

for the entire range of sensors from Carl Zeiss.


Changer Racks

Multi Sensor Rack

Art-Nr B H MMZ UPMC Accura Prismo Spectrum Contura

626100-9302-000 800 550 7/X700 7/X700 700DT/XT/G2626100-9302-010 800 450 5/X700 5/X700 700626100-9302-100 800 550 850626100-9312-000 1000 550 7/X900 7/X900626100-9322-000 1100 550 1000DT/XT/G2626100-9322-010 1100 450 1000626100-9322-020 1100 700 G2/U-Stone626100-9332-000 1250 800 10/X1200 10/X1200626100-9342-000 1600 800 10/X1600 10/X1600626100-9342-010 1600 800 MMZ-G/T

Accessories

626100-8390-000 fastening angle for MSR626100-9303-000 additional level MSR, L=800 without probe socket600660-8365-000 probe socket MT/VAST626100-9333-000 additional level MSR, L=1250 without probe socket 626100-9313-000 additional level MSR, L=1000 without probe socket 626100-9343-000 additional level MSR, L=1600 without probe socket 626100-9323-000 additional level MSR, L=1100 without probe socket

The Multi Sensor Rack (MSR) mini is a simple and

flexible changer rack for coordinate measuring

machines with small measuring range. (Probe

sockets are not included).

Multi Sensor Rack mini

Art-Nr Description

626100-9392-000 Multi Sensor Rack mini B720/H450

Accessories

600660-8365-000 probe socket MT/VAST

The Multi Sensor Rack (MSR) is an efficient and

flexible probe and sensor changer for bridge type

CMMs. By choosing which sensor and probe

sockets to mount, the new MSR types can be

configured easily to your requirements. This allows

total flexibility for future extensions of your CMM.

The sensor change is passive, i. e. the CMM

handles the change of the probe configurations.

For this purpose, the MSR is placed inside the

measuring range of the CMM. (Probe sockets are

not included).


Multi Sensor Rack duplex

Art-Nr B H Accura Prismo

626100-9304-000 800 480 5/X700 5/X700626100-9314-000 1000 580 7X/900 7/X900626100-9324-000 1250 880 10/X1200 10/X1200

Accessories


The Multi Sensor Rack duplex offers two MSR on

one CMM. To change the current MSR, it has to

be pushed out of the measuring range, rotated

through 180° and replaced into the measuring

range again. You can instantly continue with your

measurements with a new set of styli.

Changer Racks

Multi Sensor Rack accessories

Art-Nr Description

626100-9303-000 additional level MSR, L=800 without probe socket626100-9313-000 additional level MSR, L=1000 without probe socket 626100-9323-000 additional level MSR, L=1100 without probe socket 626100-9333-000 additional level MSR, L=1250 without probe socket 626100-9343-000 additional level MSR, L=1600 without probe socket 626100-8390-000 fastening angle for MSR

With these additional levels and mounting brackets

you can easily and flexibly expand your MSR. The

width of the third level is adapted to the width

of the base module. The y-axis mounting bracket

allows the fastening and adjustment of the MSR

along the y-axis of your CMM.

Probe socket MT/VAST

Art-Nr Description


This probe socket can hold one Zeiss MT/VAST

adapter plate.


MSR-T for CenterMax

Art-Nr Description

626100-9305-000 MSR-T for CenterMax, incl. 8 MT/VAST probe sockets626100-9305-100 MSR-T for CenterMax without probe sockets

Accessories

600660-8365-000 MT/VAST probe socket, single storage slot

Changer Racks

Multi Sensor Rack-Telescopic

NEW!

Easy handling and improved ergonomics make

the Multi Sensor Rack Telescopic (MSR-T) the ideal

complement to your CenterMax coordinate measu-

ring machine.

The MSR-T‘s telescopic extraction for pulling the

probe socket out of the measuring range improves

the accessibility of your styli systems and enables

easy fitting and cleaning. This prevents damage to

the probe head head of your CenterMax.

The MSR-T is easy to use and the pullout direction

can be preset to go forwards or backwards. This

makes it a flexible solution whatever the ambient

conditions of your CenterMax are. The MSR-T is

available as a conversion kit without sockets or

as a practical set including eight MT/VAST probe

sockets.


Changer Racks

ProMax

ProMax systems are automatically moving changer

racks for Zeiss CMMs. Usually, when a CMM is in

use, the probes necessary for the measuring are

provided within the measurement range. For com-

plex workpieces often ten to fifteen probes have to

be stored. As a result, up to 25% of the measure-

ment range of the CMM is used up by the changer

rack. Especially when large workpieces are measu-

red, where long probes are needed, the CMM is

restricted by fixed changer racks.

The solution: ProMax automatically transports the

probe sockets out of the measurement range

whenever a changer rack is not necessary.ProMax

is completely made up of modular components

and is therefore easily adaptable to your cmm and

quickly available. Individual linear modules are

fitted to a base frame. The modules can be adju-

sted sideways and in height. Existing measuring

plans do not have to be modified, since ProMax

plugs directly into the cmm control cabinet.

Probe sockets are not included in the delivery.

ProMax

Art-Nr for machine levels linear modules max. probe sockets fixed sockets

000000-1152-179 Contura 7 2 4 8 No000000-1152-180 Prismo 5 / Accura 5 1 2 4 Yes000000-1152-181 Prismo 7 / Accura 7 2 6 12 No000000-1152-182 Prismo 10 / UPMC 1200 3 12 15 No

Accessories

600660-8365-000 probe socket MT/VAST000000-1152-188 assembly of ProMax on CMM within EU000000-1152-187 assembly of ProMax on CMM within Germany000000-1152-186 Passive box for ProMax, to integrate fixed probe sockets000000-1152-185 Linear module 500 for ProMax, stroke 500 mm000000-1152-184 Linear module 300 for ProMax, stroke 300 mm


Changer Racks

ProMax-C for Centermax

Art-Nr Description

626100-9510-000 ProMax-C - automatic probe changer

Accessories

600660-8365-000 probe socket MT/VAST000000-1152-188 assembly of ProMax on CMM within EU000000-1152-187 assembly of ProMax on CMM within Germany626100-8510-000 3rd level for ProMax-C (new changer) without sockets

ProMax-C is an automatically moving changer rack

for the ZEISS Centermax CMM. It is designed espe-

cially for the use in production enviroment and has

ten MT/VAST probe sockets mounted on two linear

modules on two levels. The linear modules allow

(with a stroke of approx. 200 mm) to transport the

probes pneumaticaly out of the measuring range

when not needed. With your Calypso software, the

probe sockets will be automatically positioned in the

measuring range, when required.

ProMax-C 3rd level

Art-Nr Description

626100-8510-000 3rd level for ProMax-C (new changer) without sockets

Accessories


ProMax-C can be expanded with the additional

level.


Changer Racks

ProMax-G for GageMax

Art-Nr Description

626100-9420-000 ProMax-G for GageMax (without probe sockets)

Accessories

600660-8365-000 probe socket MT/VAST000000-1152-188 assembly of ProMax on CMM within EU000000-1152-187 assembly of ProMax on CMM within Germany

ProMax-G is an automatically moving changer rack

for ZEISS in line CMM GageMax. ProMax-G is espe-

cially developed for the production line. Up to five

MT/VAST probe sockets can be mounted on a ledge

that will automatically move out of the measuring

range. With your Calypso software, the probe

sockets will be automatically positioned in the

measuring range, when required.

ProMax-G lateral mounting

Art-Nr Description

626100-9430-000 ProMax-G probe changer lateral mounting

Rack with two ProMax-G on two levels, 8 probe

sockets MT/VAST total, for mounting on GageMax

base plate.


ProMax accessories

Art-Nr Description

000000-1152-184 Linear module 300 for ProMax, stroke 300 mm000000-1152-185 Linear module 500 for ProMax, stroke 500 mm000000-1152-186 Passive box for ProMax, to integrate fixed probe sockets000000-1152-187 assembly of ProMax on CMM within Germany000000-1152-188 assembly of ProMax on CMM within EU

Accessories for the extension of your ProMax

system. Please give us a call, we will give you a

quotation for the installation and integration into

your existing system.

(Only for use with ProMax systems from order no.

000000-1152-179 to 000000-1152-182).

Changer Racks


Stylus Set-up Device

FixAssist – saves time

The assembly of styli systems requires a lot of diligence

and precision. We recommend the FixAssist stylus

set-up device to make sure that your styli systems

can always meet the requirements on accuracy and

can be reproducibly assembled. This assembly station

reliably ensures that the necessary angularities and

stylus orientations are met.

With the help of the convenient set-up device, you

are able to build your styli systems beginning with

the adapter plate. Extensions, cubes or clamping

pieces can be added and instantly adjusted.

Together with the appropriate tool set, the

FixAssist is an extremely useful addition to

your CMM.

Do you align the angles of your styli systems

directly on your coordinate measuring machine?

What is the hourly expense of your CMM?

FixAssist enables you to quickly and easily cut

costs by setting up your styli systems away from

the CMM. You do the math.


Stylus Set-up Device

FixAssist VAST linear

Art-Nr Description

626109-9120-000 FixAssist VAST linear, incl. tool kit

Accessories

626109-9150-000 XXT adaptor set for FixAssist Linear

The probing system alignment device FixAssist

VAST linear is used to hold a MT/VAST changer rack

adapter plate while mounting a probing system

and to align the probing system precisely around

the CMM Z-axis and the horizontal axis. The device

is delivered including a tool kit for mounting

probing systems.

Your advantages are that the CMM is not required

for pre-adjustment. FixAssist allows easy handling

wich prevents damage to your probes and styli and

it secures fast and reproducible probe assembly as

well as high measurement certainty through

optimally adjusted probes.

XXT Adapter set FixAssist linear

Art-Nr Description

626109-9150-000 XXT adapter set for FixAssist Linear

For the adjusting of XXT styli systems with the

FixAssist linear.

Consists of:

- adapter plate made of stainless steel

- magnetic adapter prism made of stainless steel

Set up device kit for knuckle joints

Art-Nr Description

626109-9020-000 set up device kit for knuckle joints626109-0025-000 set up device for knuckle joints DG 11

Accessories

600342-9002-000 knuckle joint, M5, titanium

Set up device for knuckle joints diameter 11 mm

(600342-9002-000). With this Set up device,

knuckle joints can be easily adjusted accurately

(1°) to the requested angle. Kit includes 5 knuckle

joints, set up device and tools.

Modular according to your wishes

The MSC modular probe cabinet can be designed

to your individual requirements. Select a cabinet

with glass doors or the standard model with metal

doors and adapt the configuration to fit your

requirements.

Store your valuable styli systems clearly arranged

and easily accessible in a safe place. The robust

MSC multi-sensor cabinet is designed for use on

the shop floor and in the measuring lab. The basic

configuration of the MSC for MT/VAST comprises

30 MSC probe sockets on five adjustable bars.

Useful accessories make it easily adaptable to your

requirements and you can mount additional MSC

probe sockets by yourself.

Styli and extensions can be stored on pallets of

different sizes. The pallets can be mounted in

vertical and horizontal positions. A tool tray

provides the required tools for the stylus assembly.

The MSC can be easily upgraded with additional

storage bars.


Probe Cabinets

Safely store your styli systems


Probe Cabinets

Probe cabinet MSC, glass doors MT/VAST

Art-Nr Description

626100-9025-100 probe cabinet MSC, with glass doors and 30 sockets MT/VAST

Accessories

626100-8022-000 tool tray for probe cabinet MSC626100-8024-000 additional level for cabinet MSC626100-8021-000 pallet for 67 styli M5 for cabinet MSC626100-8011-010 probe socket MT/VAST for cabinet MSC626100-8023-000 shelf for cabinet MSC

Multi Sensor Cabinet MSC to store probe configu-

rations, styli and accessories for MT/VAST.

Design: cabinet with glas doors, colour: light

gray RAL7035, lock, external dimensions WxDxH

1000x400x2000 mm. Incl. 5 mounting bars with

30 probe sockets. Position, height and depth of

the levels are adjustable.

Probe cabinet MSC MT/VAST

Art-Nr Description

626100-9025-000 probe cabinet MSC, with 30 sockets MT/VAST

Accessories

626100-8022-000 tool tray for probe cabinet MSC626100-8024-000 additional level for cabinet MSC626100-8021-000 pallet for 67 styli M5 for cabinet MSC626100-8011-010 probe socket MT/VAST for cabinet MSC626100-8023-000 shelf for cabinet MSC

Multi Sensor Cabinet MSC to store probe configu-

rations, styli and accessories. For MT/VAST.

Design: cabinet with metal sheet doors, colour:

light gray RAL7035, lock, external dimensions

WxDxH 1000x400x2000 mm. Incl. 5 mounting bars

with 30 probe sockets. Position, height and depth

of the levels are adjustable.


Probe Cabinets

1. Choose the cabinet type You can choose between the cabinet with glass doors and the standard type cabinet with metal doors. Both

have a basic equipment of five level bars.

Design your own MSC

Art.-Nr Description Qty.

626100-9015-000 Probe cabinet MSC with metal doors, W x D x H 1000x400x2000 mm,

without probe sockets , incl. 5 level bars

626100-9015-100 Probe cabinet MSC with glass doors, W x D x H

1000x400x2000 mm, without probe sockets , incl. 5 level bars


626100-8023-000 Ground level compartment for the probe cabinet MSC,

powder-coated, max. carrying capacity: 60kg

626100-8024-000 Additional level bar for the probe cabinet MSC

4. Order via Fax: +49 (0) 7365 9208-29

2. AdditionsDesign the interior of your new MSC yourself and get exactly what you require.


626100-8011-010 Probe socket MT/VAST for MSC

626100-8012-000 Probe socket ST/ST3 for MSC

626100-8013-000 Probe socket DSE for MSC

626100-8014-000 Probe socket RDS for MSC

626100-8015-000 Probe socket XXT for MSC

626100-8021-000 Pallet for 67 styli M5 for MSC

626100-8022-000 Tool tray for MSC

3. Combining probe sockets and accessoriesEquip your MSC with various probe sockets, probe pallets or the handy tool tray.

Name Dept.

Comp.

Street ZIP/Loc.

Phone Email


CMM accessories

Productivity for all ZEISS CMM`s

Probe sensor cabinet

Loading system forDuraMax

Pallet rack

Prep table

MSC probe sensor cabinet

Protect your valuable probes ans styli systems from

dirt and damage in the MSC Multi Sensor Cabi-

net. The cabinet allows you to store your probes

making them easy to locate and remove for use.

Art-Nr. 626100-9025-100

Our machine accessories allow you to prepare your

measuring tasks quickly and efficiently. Robust and

flexible storage, work, and retention areas for all

of your accessories create the ideal working envi-

ronment for your coordinate measuring machine.

Prep table

The new prep table is an ergonomic work sta-

tion designed to meet the needs of measuring

technology. It provides a large working surface

for the preparation of jigs, the assembly of styli

systems, and for cleaning probes. The drawers

and cupboard allow you to keep things tidy and

enable the storage of cleaning materials, tools, and

documents. The magnifier (not included) is useful

during cleaning work and, thanks to the integrated

LED lighting system, even allows you to work if the

ambient light is poor.

Art-Nr. 626109-9222-100

Pallet rack

The pallet rack allows you to store your fixture

pallets. Two 300 x 200mm pallets or one 500 x

500mm pallet can be stored on the rack‘s shelves.

The rack has three height-adjustable shelves and

can be extended as required.

Art-Nr. 626109-9222-000

For more information



Tools

Cleanliness is required for exact measurements.

We provide the right care products needed for

your coordinate measuring machine and your

probing system equipment.

The right accessories for your daily

needs

We provide a wide range of approved accessories

for the optimal, time-saving assembly of your

styli systems. Our selection of pin wrenches, hook

wrenches and torque spanners allow you to reliably

mount sensitive stylus components and avoid

damaging the styli and extensions. During the

assembly of your styli systems, make sure that all

connections are rigid. With the right tools this can

be done in no time.


Tools

Tool kit

Art-Nr Description

626109-9010-000 tool kit

Accessories

602030-0002-000 hex wrench DIN 911, BSW1,5000000-0015-248 hex wrench DIN 911, SW4602030-0021-000 hex wrench DIN 911, BSW2,5626109-0010-000 torque hex wrench 2 Nm, 2,5 mm600341-0260-000 stylus extension, M5, V2A000000-0015-245 hex wrench DIN 911, SW2000000-0015-247 hex wrench DIN 911, SW3602030-0222-000 pin Wrench, 2,9626109-0013-000 hook wrench DG20626109-0012-000 hook wrench DG11

Tool kit for styli assembly including 13 pcs. E.g.

hook wrenches, pin wrenches, hex wrenches,

torque wrench.

Torque hex wrench, 2 Nm

Art-Nr Description

626109-0010-000 torque hex wrench 2 Nm, 2,5 mm

The torque wrench with hex wrench 2,5 mm is

used to open and close screws on ZEISS adapter

plates e.g. MT/VAST plates and ST/ST3 plates.


Set of spanner wrenches

Art-Nr Description

626119-0001-000 set of spanner wrenches 5xDG11, 5xDG20

Accessories

626109-0013-000 hook wrench DG20626109-0012-000 hook wrench DG11

includes:

5 x 626109-0012-000 spanner wrench DG11

5 x 626109-0013-000 spanner wrench DG20

Hook wrenches

Art-Nr Description

626109-0018-000 hook wrench DG5626109-0012-000 hook wrench DG11626109-0013-000 hook wrench DG20

A hook wrench is used to assemble and disassemble

styli and extensions. Large torques can be applied.

Tools

Pin wrench ZEISS standard

Art-Nr Description

000000-0015-323 pin wrench, 1,1

000000-0015-328 pin wrench, 2,9

A pin wrench is used for the assembly and disas-

sembly of styli. It can be used on both ends.


Hex wrenches

Art-Nr Description

602030-0042-000 hex wrench DIN 911, BSW0,9602030-0002-000 hex wrench DIN 911, BSW1,5000000-0015-245 hex wrench DIN 911, SW2602030-0021-000 hex wrench DIN 911, BSW2,5000000-0015-247 hex wrench DIN 911, SW3000000-0015-248 hex wrench DIN 911, SW4626109-0035-000 torx wrench T6626109-0037-000 inbus wrench, 4mm, L350

The hex wrench is used for the tightening of cylin-

der head screws with a hex socket, e.g. for joints.

Tools

Other pin wrenches

Art-Nr Description

602030-0001-000 pin wrench, 1,2602030-0027-000 pin wrench,1,7602030-0222-000 pin Wrench, 2,9

Pin wrenches for small hole diameters.

Cleaning and support

Art-Nr Description

000000-0084-895 JFA-CLEAN bottle 1L626119-0010-006 Polyamide-stretch-glove with PU coated palm000000-1359-469 microfiber cleaning tissue626119-0010-007 swabs Knitted Polyester 1,6mm, (500 pcs.)626119-0010-008 swabs Knitted Polyester 3,2mm, (500 pcs.)626119-0010-009 swabs Knitted Polyester 6,4mm, (500 pcs.)626119-0010-005 Dust off 360 Super000000-0424-218 Cleaning cloths Absorbond TX409,9" x9"

Cleanliness is essential for precision measuring.

The workpiece has to be cleaned to achieve

optimum measuring results. Our cleaning material

is recommended for all ZEISS measuring machines.


CMM Accessories

Calibrate styli precisely

Every coordinate measuring machine and every sensor

– no matter if tactile or optical – has specific require-

ments for its calibration process. That’s why we offer

you a wide range of different sized reference spheres.

Custom sizes and special surfaces for optical sensors

are available on demand.

You can mount up to three spheres on the ZEISS RSH

reference holder system for maximum flexibility. A

range of thermally stable holders out of invar or carbon

fibre for usage on the shop floor can be found in our

internet shop www.probes.zeiss.com.


CMM Accessories

RSH Reference sphere holder with spheres

Art-Nr Description

600332-9265-000 reference sphere RSH-214 with stand600332-9266-000 reference sphere RSH-364 with stand600332-9267-000 reference sphere RSH-514 with stand

Accessories

600332-8443-000 reference sphere, RS-D8-C, M6600332-8446-000 reference sphere, RS-DK30-C600332-8445-000 reference sphere, RS-DK25-C600332-8444-000 reference sphere, RS-DK15-C

The reference sphere holders are available with

different heights of 214, 364, and 514 mm for the

reference spheres. This enables optimum adaption

in line with requirements for different machine

sizes and special equipment.

There is a complete set for each of these sizes

consisting of a reference sphere holder and a 30

mm ceramic reference sphere with a shaft. Fixing

material, tool, certificate, and brief instructions.

The set is supplied in a practical transport and

storage case.

RSH Reference sphere holder

Art-Nr Description

600332-9165-000 basic set RSH-214 without calibration sphere600332-9166-000 basic set RSH-364 without calibration sphere600332-9167-000 basic set RSH-514 without calibration sphere

The reference sphere holders are available with

different heights of 214, 364, and 514 mm for the

reference spheres. This enables optimum adaptati-

on in line with requirements for different machine

sizes and special equipment. Technically, this is

the same as the „RSH Complete“ reference sphere

holder. However, it is delivered without reference

spheres.


CMM Accessories

Reference spheres RS

Art-Nr system DK L DG TMAT weight (g)

600332-8443-000 M6 8,00 74,10 18,00 ceramics 90600332-8444-000 M6 15,00 77,60 18,00 ceramics 100600332-8445-000 M6 25,00 82,60 18,00 ceramics 114600332-8446-000 M6 30,00 85,10 18,00 ceramics 133

These reference spheres can be mounted on all

RSH systems. They have a ceramic sphere and a M6

thread. The length from the middle of the sphere

to the base is 70,1 mm. All reference spheres come

with a certificate.

For more reference spheres and special holders, see our Internet shop at



CMM Accessories

Multi-Feature-Check

The Multi-Feature-Check is a method for the deter-

mination of the task specific measurement uncer-

tainty and of the measurement process suitability

for almost all workpiece features including form

and position, being found in coordinate metrology.

Relating to the particular CMM, measuring uncer-

tainties can be determined and a conclusion about

the test process applicability can be deducted.

The following inspection features can be selected

depending on the user’s parts spectrum. For these

features - related to the CMM used - the measure-

ment uncertainties can be determined and the

suitability of the measurements can be stated:

- diameter, length, angle

- straightness, flatness, roundness, cylindricity

- parallelism, squareness, inclination, position,

concentricity, coaxiality, symmetry

- radial run-out, axial run-out, total radial run-out,

total axial run-out

When using this method the measurement uncer-

tainties and the suitability of the measurements are

determined realistically taking into account

- the current on site temperatures

- by means of workpiece-similar material and

- surface properties of the test piece.

Art-Nr Description

626001-0730-000 Multi Feature Check626001-0730-020 Multi Feature Check Calypso Lizenz626001-0790-000 DKD-calibration Multi Feature Check

Artefacts

As an operator of measuring machines, you must

be sure that your measuring equipment meets the

required specifications at all times. This is absolute-

ly vital for the consistently high quality of the parts

you manufacture. Accuracy monitoring at regular

intervals provides the foundation for accurate,

reliable measuring results. For this purpose, we

offer artifacts for a wide variety of applications.

Inquiries to:

Carl Zeiss Industrielle Messtechnik GmbH

Robert-Bosch-Str. 27

73431 Aalen

Tel.: +49-7361-9277-10

Fax: +49-7361-9277-55


CMM Accessories

CMM-Check with case

Art-Nr Description

000000-1103-602 CMM-Check with case626001-0100-100 flightcase for CMM-Check626001-0122-020 software CMM-Check / SW, UMESS UNIX / LINUX626001-0130-020 software CMM-Check / SW Calypso000000-1103-606 DKD-calibration CMM-Check

000000-1103-607 manufacturer calibration CMM-Check

CMM-Check can be used to check coordinate

measuring machines in accordance with DIN EN

ISO 10360 and VDI/VDE 2617. The following fea-

tures can be measured with the artifact and subse-

quently evaluated with the software:

- Probing behavior of the probing system

- Scanning performance of the probing system

- CMM as a form measuring machine incl. filter

characteristics

- Linear measuring errors

- Four-axis error of the CMM with rotary table

(optional)

The basis of the universal artifact consists of a

bend-resistant carrier on which calibrated, high-

precision dimensional and form standards are

mounted:

- one setting ring gage, 50 mm diameter

- one ceramic sphere, 30 mm diameter

- one Flick standard (precision cylinder with

two flat polished sections of approx. 10 µm

and 250 µm)

- two parallel gage blocks, 50 mm and 400 mm

- two ceramic spheres (optional), 30 mm diameter

Art-Nr Description

000000-1103-639 Probe-Check with case626001-0422-020 software Probe-Check for SW UMESS UNIX / LINUX

626001-0430-020 software Probe-Check for SW Calypso000000-1103-642 DKD-Kalibrierung Probe-Check000000-1103-643 Werkskalibrierung Probe-Check

Probe-Check

Probe Check is a procedure to test the probing

and scanning behavior of the probe in combination

with the coordinate measuring system in accordance

with VDI/VDE 2617.

Description:

The artifact basis consists of a bend-resistant carrier

on which

- one ceramic sphere, 30 mm diameter and

- one setting ring gage, 30 mm diameter are

mounted.

- Both are calibrated, high-precision standards.

Needless to say, the artifact can be used on

CMMs from all manufacturers.


CMM Accessories

Multi-Sensor-Check

Art-Nr Description

626001-0830-000 hardware Multi Sensor Check for SW Calypso626001-0830-020 software Multi-Sensor-Check for Calypso626001-0890-000 DKD-calibration Multi-Sensor-Check

The monitoring procedure for coordinate measu-

ring machines with tactile and optical sensors.

The multi-sensor check is a procedure for the

standardized checking of coordinate measuring

machines (CMMs) with tactile/optical sensors. The

universal, calibrated test block is delivered with

complementing control and analysis software. The

multi-sensor check can be used to check coordina-

te measuring machines as per DIN EN ISO 10360-2

and VDI/VDE 2617 Sheet 6.1:

- Probe deviation of measuring head system

- Scan deviation of measuring head system

- Length measurement deviation

- Both the probe deviation and length measurement

deviation are checked using tactile and optical

methods.

The test block basis is a bend-resistant base body

to which high-precision, calibrated measuring

implements are applied:

- A special adjusting ring for tactile and optical

measurements, diameter of 16 mm

- A ceramic precision sphere, 25 mm in diameter

- Two parallel slip gauges, 50 mm and 200 mm in

length

- A glass scale, 200 mm in length; the glass scale

incorporates precise, circular markings for

checking the probe deviation and a division scale

for checking the length measurement deviation.


Clamping Systems

clamped directly outside the measuring range

either directly to the pallet, a vise, the three-jaw

chuck or with a fixture made from the CARFIT®

CMB kit.

Ask our CAD experts if you need a custom-made

fixture for your individual workpiece. We have

years of experience in designing manual and auto-

mated clamping fixtures for series measurement on

coordinate measuring machines.

Fast exchange of your workpieces

Mounting your workpieces takes a lot of time.

With our changeable mounting system, you can

position your workpieces fast, easily and with

repeatable accuracy on your CMM.

A pallet system with interface allows a fast

exchange between several clamping devices. The

pallets are simply mounted by hand on the adap-

ter plate, which is fixed to the CMM. The special

design of the interface enable a safe and

reproducible positioning. Workpieces can be


Clamping Systems

Pallet system 300x200

Interface pallet set

Art-Nr Description626109-9220-130 interface set bench vice626109-9220-140 interface set jaw chuck

Accessories626109-9220-040 jaw chuck interface626109-9220-030 bench vice interface626109-9220-020 raster interface M6626109-9220-010 support plate

This handy interface set contains everything you

need as initial equipment:

- 1 x Support plate

- 1 x Raster interface 300x200

And either 1 x bench vice intreface (73 mm)

or 1 x three chuck interface (125 mm)

Support plate

Art-Nr Description626109-9220-010 support plate

This support plate can be installed directly within

the measureing range of your CMM.

On the statically defined 3-roll-support you can

fast and easily attach the appropriate interface.

In case you need to measure many different work

pieces or having a variety of measurement tasks to

complete, it is a major advantage if you are able to

exchange your fixtures fast and easily.

Our interface pallets are an efficient and timesaving

solution.

No more loss of precious time, because you won`t

have to adjust the fixtures to the workpieces.


Raster interface

Art-Nr Description626109-9220-020 raster interface M6

Accessories600062-0210-000 CARFIT® CMB KIT - System E

This raster pallet for the changeable interface

system has a M6 25 mm hole spacing. It allows

you to assemble your own mounting fixtures with

bracket clamps or other elements included in our

clamping kit (000000-0411-562).

Bench vice interface

Art-Nr Description626109-9220-030 bench vice interface

This interface pallet holds an attached bench vice

with a jaw width of 73 mm and a maximum spread

of 100 mm. The bench vice is mounted with brak-

kets to the pallet and can be moved on the plate.

Clamping Systems

Jaw chuck interface

Art-Nr Description626109-9220-040 jaw chuck interface

300 x 200 mm interface with an attached three

jaw chuck. A handy catch to operate the chuck is

also provided.


Clamping Systems

Pallet system 500x500

Art-Nr Description626109-9220-622 Changeover interface set raster 500x500, M12626109-9220-652 Changeover interface set base 500x500, M12

Accessories626140-9111-200 Temperature sensor with plastic housing, open cable end 3 m626109-9220-550 Workpiece pallet 500x500 base626140-9121-500 TSM-50 contact unit f. temperature sensor, cmm side626140-9122-500 Temperature interface TSP-50 pallet contact unit626140-9112-200 Temperature sensor with steel housing, open cable end 3 m626109-9220-520 Workpiece pallet 500x500 raster

Interface pallet set

The changeover interface set contains a workpiece

pallet (with or without M6 hole patterns), a base

mounting plate, and two insertion aid units that

can be mounted to your coordinate measuring

machine. The base mounting plate and insertion

aid units are available for coordinate measuring

machines with M10 fixing holes, such as DuraMax,

and for coordinate measuring machines with M12

fixing holes. The pallet and base mounting plate

are prepared for the assembly of an interface for

the connection of a jig-integrated temperature

sensor.

NEW!

NEW!

Art-Nr Description626109-9220-520 Workpiece pallet 500x500 raster626109-9220-550 Workpiece pallet 500x500 base

Accessories626140-9122-500 Temperature interface TSP-50 pallet contact unit

Interface pallet

500 x 500mm workpiece pallets are made from

aluminium and have two carrying handles. They

are prepared for the assembly of a temperature

transfer interface. Two versions are available: With

M3 threaded bores in a 50 x 50 pattern and wit-

hout bores (basic version).


Support plate

Art-Nr Description626109-9220-512 Base mounting plate M12 for pallet 500x500

Accessories626109-9220-550 Workpiece pallet 500x500 base626109-9220-520 Workpiece pallet 500x500 raster

Clamping Systems

Torque nut

Art-Nr Description626109-0031-000 Torque Nut, M6626109-0033-000 Torque Nut, M6 small626109-0034-000 Torque Nut, M8

The base mounting plate is mounted onto the

table of the coordinate measuring machine. It is

available in two versions for attachment to M10

and M12 threaded bores. It is delivered with fixing

material and corresponding insertion aid units.

Infinitely variable, single-sided effective torque nuts

made of stainless steel. Thread sizes M6 and M8.

NEW!

NEW!

Improved productivityA clamping fixture precisely matched

to the workpiece and the measuring

machine is absolutely vital for ensuring

repeatable accuracy in serial measure-

ment results. By integrating temperature

sensors into the fixture, the workpiece

temperature can be read and processed

without delay. Our manual or automated

shifting and loading units help you to

avoid collisions during loading and set-up

times will be reduced.

Short run-up timeIn close collaboration with application

technology specialists, we optimize your

sensor system and check workpiece

accessibility by means of simulations.

This shortens run-up times in the start-up

phase. The utilization of standard compo-

nents results in a cost-efficient design.

Optimized for continuous measurement

One stop shop Our expertise as the machine manufactu-

rer and the experience gained from

thousands of customer projects mean

that we will create the best solution for

your requirements. See for yourself and

contact us for a non-obligation consul-

tation.

Individual clamping fixtures


Temperature interface

Clamping Systems

TSM-50 contact unit for temperature sensor, CMM side

Art-Nr Description626140-9121-500 TSM-50 contact unit f. temperature sensor, cmm side

This unit is incorporated into the base mounting

plate 626109-9220-510 incl. cable (3 m) with a

SUB-D female connector for the connection to the

CMM.

TSP-50 contact unit for temperature sensor, pallet side

Art-Nr Description626140-9122-500 Temperature interface TSP-50 pallet contact unit

Accessories626140-9112-200 Temperature sensor with steel housing, open cable end 3 m626140-9111-200 Temperature sensor with plastic housing, open cable end 3 m

The contact unit is integrated into a 500x500

pallet and transmits the temperature sensor signals

to the machine-side contact unit. The sensor can

be connected directly via clamping contacts.

Temperature sensors

Art-Nr Description626140-9111-200 Temperature sensor with plastic housing, open cable end 3 m626140-9112-200 Temperature sensor with steel housing, open cable end 3 m626140-9130-000 Spare sensor 626140-9132-000 Extension cable SUB-D/SUB-D, 3m

These temperature sensors can be directly

integrated into the clamping fixtures. They have

a spring-loaded sensor head, open cable ends

and ferrules (cable length = 3 m). They are

available with a plastic or steel housing.


Clamping Systems

CMB-E clamping kit

Art-Nr Description600062-0210-000 CARFIT® CMB KIT - System E

Accessories600062-0116-000 grid plate CMB 700x800x30 (J&P Art.Nr.: 13 02 0008)600062-0117-000 grid plate CMB 500x500x20 DuraMax (J&P Art.Nr.: 13 02 0009)600062-0112-000 grid plate CMB 250x250x20 (J&P Art.Nr.: 13 02 0003)600062-0113-000 grid plate CMB 400x300x20 (J&P Art.Nr.: 13 02 0005)626109-9220-020 raster interface M6600062-0115-000 grid plate CMB 600x800x30 (J&P Art.Nr.: 13 02 0007)600062-0111-000 grid plate CMB 500x400x20 (J&P Art.Nr.: 13 02 0001)600062-0114-000 grid plate CMB 400x600x20 (J&P Art.Nr.: 13 02 0006)

The extensive CARFIT® CMB KIT - System E con-

tains clamping and positioning elements that can

be used to quickly and easily assemble workpiece-

specific clamping fixtures. No baseplate is included

in the kit.

CARFIT® CMB M6 grid plate

Art-Nr Description600062-0112-000 grid plate CMB 250x250x20 (J&P Art.Nr.: 13 02 0003)600062-0113-000 grid plate CMB 400x300x20 (J&P Art.Nr.: 13 02 0005)600062-0114-000 grid plate CMB 400x600x20 (J&P Art.Nr.: 13 02 0006)600062-0111-000 grid plate CMB 500x400x20 (J&P Art.Nr.: 13 02 0001)600062-0117-000 grid plate CMB 500x500x20 DuraMax (J&P Art.Nr.: 13 02 0009)600062-0115-000 grid plate CMB 600x800x30 (J&P Art.Nr.: 13 02 0007)600062-0116-000 grid plate CMB 700x800x30 (J&P Art.Nr.: 13 02 0008)

The grid plate is the basis for the building of a

series basic measurement fixture. It has a 50 mm

grid pattern of M6 tapped holes. The grid plate

has 4 mounting holes 200 x 200 mm. The

Aluminum is hard-coated.

Visit www.com for a huge assortment of Junker & Partner Kits and individual Parts.


Request Styli M5

Fax request for M5 styli

Spehre material (TMAT)

Ruby (R)

Silicon Nitride (SiN)

Diamond (Diam)

Shaft material (SMAT)

Tungsten Carbide (HM)

Ceramic (Ker)

Carbon Fibre/ThermoFit (TF)

Typ DK mm L mm ML mm MLE mm DS mm DSE mm TMAT SMAT Quantity

Company:

Department:

Name, First:

Address

Zip / City:

Phone: Fax:

E-Mail:

Fax: +49 (0)7365-9208-29

Type 1 Type 2

Type 3 Type 4


Request Styli M5

Fax request M5 disc-/ cylindrical styli

Disc / cylindrical material (TMAT)


Ruby (R)

Ceramic (Ker)

Shaft material (SMAT)


Ceramic (Ker)

Typ DK mm L mm ML mm B mm DS mm TMAT SMAT Quantity

Fax: +49 (0)7365-9208-29

Type 1 Type 2

Company:

Department:

Name, First:

Address

Zip / City:

Phone: Fax:

E-Mail:


Fax request M5 angle block

material titaniummaterial aluminum

Standard ThermoFit Pro

Type Angle W in degree Quantity

Fax: +49 (0)7365-9208-29

Request Angle Block M5

Company:

Department:

Name, First:

Address

Zip / City:

Phone: Fax:

E-Mail:

Type 1 Type 2


Clear conceptSimulation, visualization and constant communication

with our customer - from the quotation to the delivery

is the key to a successful RoboMax project.

Thinking aheadTo provide you with a future-proof solution, we only

use globally available components for easy spare parts

procurement.

RoboMax®

Visible Productivity

Automate your ZEISS cmm

Only a few steps from the idea to its completion

Ask us

Increased ProductivityGet higher throughput and have lower down-

times in your production.

Guaranteed ConnectivityBy modularly connecting the Zeiss CMM, robot

and peripherals with the factory material flow.

We can assist you to increase the

productivity of your quality control.

Send your inquiries to:

Tel.: +49 7365 9208-210

Fax: +49 7365 9208-29

Mail: [email protected]


Carl Zeiss3D Automation GmbH

Telefon: +49 73 65 9208-210Telefax: +49 73 65 9208-29Mail: [email protected]: www.probes.zeiss.com

V201

1_07

_E_3

.04

Prin

ted

in G

erm

any

Subj

ect t

o ch

ange

in d

esig

n an

d sc

ope

of d

eliv

ery

and

as a

resu

lt of

ong

oing

tech

nica

l dev

elop

men

t ©

Car

l Zei

ss 3

D Au

tom

atio

n Gm

bH ©

con

cept

, tex

t and

des

ign:

Car

l Zei

ss 3

D Au

tom

atio

n Gm

bH

Documents

Probe System Equipment MT/VAST - Metro Place · Email: [email protected] Version: V2011_07_E_3.04 Content ... MT/VAST. 3 Productivity for your ZEISS measuring machine As the manufacturer