Pro-kuvasto eng

CATALOGUE

Valid from 1 September 2011

PUBLIC PREMISES WALLS, CEILINGS AND FLOORS ALUMINIUM FRAME IMPACT GUARDS, HANDRAIL AND

PROFILES HATCHES ENTRANCE SUPPORT CARPETS HANDLES

DUURI OYTapulikaupungintie 35PL 26, 00750 HelsinkiFINLANDTel. (09) 351 050fax (09) 3510 [email protected]

www.dione.fiwww.dionepro.fi

D-PROFILE ABKabelvägen 1055302 JönköpingSWEDENTel. +46-(0)36-186363Fax +46-(0)36-186366 [email protected]

D-PROFILE ASRevefaret 123060 SvelvikNORWAYMobile +47 90 47 06 30Fax +47 33 77 32 [email protected]

ООО «Дюри Профайл Рус»Россия 143362 МоскваРОССИЯг.Апрелевка, Сентябрьская ул., д.12Тел. +7-495-982 3875 Факс: +7-495-982 3875Эл. почта: [email protected]

SIA D-profileRīgas iela 6LV-2114 OlaineLATVIATel. +371 67783506Fax +371 [email protected]

CATALOGUE

The DionePro selection provides you with quality products for professional use. The products are ideal for public premises and designed to withstand extremely hard wear and tear.

• Profiles for public premises• Manholes as well as wall and ceiling access hatches• Handrails and impact guards• Carpets for entrance tambours• Accessibility products

CONTENT OF THE CATALOQUECOVER STRIPS. ... ... ... ... ... ... ... ... ... ... ...8

FIRE THRESHOLDS ... ... ... ... ... ... ... ... ...9

EDGE TRIMS. ... ... ... ... ... ... ... ... ... ... ... ...9

RAMPS WITH LEVEL DIFFERENCE.. ...10

END PROFILES ... ... ... ... ... ... ... ... ... ... ...11

STAIR EDGE PROFILES. ... ... ... ... ... ... ...12

TILING PROFILES ... ... ... ... ... ... ... ... ... ...20

CORNER PROTECTION PROFILES ... ...22

SKIRTINGS ... ... ... ... ... ... ... ... ... ... ... ... ...23

COLUMN COLLARS . ... ... ... ... ... ... ... ...24

CURVED PROFILES ... ... ... ... ... ... ... ... ...25

CUSTOM-MADE PRODUCTS ... ... ... ...25

EXPANSION JOINT PROFILES ... ... ... ...26

ENTRANCE CARPETS WITH ALUMINIUM

FRAME ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...29

INSPECTION AND ACCESS HATCHES ... ... ... ... ... ... ... ... ... ... ... ... ... ...32

VINYL-COATED HANDRAILS. ... ... ... ...60

VINYL-COATED IMPACT GUARDS .. ...62

VINYL-COATED CORNER PROTECTION PROFILE. ... ... ... ... ... ... ... ... ... ... ... ... ... ...63

SHOPPING TROLLEY SHELTERS .. ... ...65

CORNER PROTECTION PROFILES FOR PARKING HALL. ... ... ... ... ... ... ... ... ... ... ... ... 65

IMPACT GUARDS FOR PARKING HALL ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...66

SUPPORT HANDRAILS FOR SENIOR CITIZENS’ HOMES

AND ASSISTED LIVING FACILITIES . ...6

COLOUR MAP ... ... ... ... ... ... ... ... ... ... ... ...64

FREQUENTLY ASKED QUESTIONS ... ... .70

DELIVERY TERMS ... ... ... ... ... ... ... ... ... ... .71

Minor things often matter most Therefore DionePro is the best solutionDionePro - high-quality products for professional use

Our selection includes a variety of options for products and solutions that withstand hard wear and tear in public premises. First-rate DionePro products are designed for professional use in particular, which makes it easy to create impressive general impressions with minor but significant details in tones.

Ordering our standard products is easy by using the product's specific product code. Samples of most of our products are available on order and enable you to decide whether they fit in with the rest of your interior decoration.

PROFILESFOR PUBLIC PREMISES

When you need elegant and reliable solutions.

Quality DionePro profiles made of stainless steel are designed for public premises and withstand extremely hard use. Stylish and strong materials preserve their fresh and modern look for a long time. Our selection includes a wide variety of impressive and durable profile options.

All DionePro profiles are tested for wear and tear in accordance with our quality system. We also make every effort to ensure that the delivery speed of our products is excellent, and the products are safe and easy to install. All our tested standard products with different mounting methods are, in no time at all, available to customers from our warehouse, which makes their installation easy and cost-effective.

We also make custom-made special profiles.

PROFILES FOR PUBLIC PREMISES www.dionepro.fi 7

PROFILES FOR PUBLIC PREMISES 8 www.dionepro.fi

Durable finish

COVER STRIPSPublic premises are most often provided with glue or screw-mounted cov-er strips. The cover strips separate different materials and put the finishing touches to expansion joints. Standard strips with a width of 30–120 mm are directly available from stock.

Our new product, a hard CPL-coated oak imitation cover strip, is also suitable for public premises subject to hard use. The strip is provided with an inconspicuous and secure nail/plug mounting.

FOR SEAM

FINISH

STAINLESS STEEL COVER STRIPS FOR PUBLIC PREMISES

Material: made of ground stainless steel suitable for public premises. Material thickness 1.5 mm. Fastening: screw or glue mounting. We recommend fastening the glue-mounted strips with assembly glue.Cutting: strips are shortened with a wheel fit for cut-ting stainless steel. The wheel is attached to an angle grinder. A small number of profiles can be cut with a hacksaw.Applications: offices, hotels, schools, shopping cen-tres and other public premises where no hard-wheeled pallet jacks are used.

Width/type Length Product code

S/O

30 mm, curved surface, without holes 300 cm 7093005-R S

30 mm, ridged centre, without holes 300 cm 7094605-R S

38 mm, aluminium/stainless steel, with-out holes

270 cm B2 AS 270-R S

40 mm, ridged centre, without holes 300 cm 7094505-R S

40 mm, ridged edges, with holes 90 cm A4 RST 90 S

40 mm, ridged edges, with holes 180 cm A4 RST 180 S

40 mm, ridged edges, with holes 300 cm 7095305 S

40 mm, ridged edges, with holes 300 cm 7095305-R S

45 mm, aluminium/stainless steel, plug-mounted

270 cm KI AS 270 S

50 mm, ridged edges, without holes 300 cm 7094405-R S


60 mm, ridged edges, without holes 90 cm A5 RST 90 S

60 mm, ridged edges, without holes 180 cm A5 RST 180 S




70 mm, ridged edges, with side holes 300 cm 7095015 S

80 mm, ridged edges, without holes 90 cm A6 RST 90-R S











*S = IN STOCK O= ORDER PRODUCT

Curved surface

Ridged centre

Ridged edges


FIRE THRESHOLD

EDGE TRIMSMaterial: made of ground stainless steel suitable for public premises.Material thickness 1.5 mm. An option made of stainless steel coated aluminium is also available.

Fastening: screw or glue mounting. We recommend using the Duuri assembly glue for the fasten-ing of glue-mounted profiles.

Cutting:trims are shortened with a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder.

Applications: offices, hotels, schools, shopping centres and other public premises where no hard-wheeled pallet jacks are used.

CPL-COATED COVER STRIPSFOR PUBLIC PREMISESMaterial: made of CPL-coated oak imitation aluminium profile fit for public premises.Fastening: plug mounting.Applications: offices, hotels, schools, shopping centres and other public premises where no hard-wheeled pallet jacks are used.

Width/type Colour Length Product code

S/O

45 mm, CPL cover strip Oak 270 cm K2 OA 270 S


The fire threshold is designed in cooperation with architects to im-prove the comfort and safety in assisted living facilities that have fire doors. The fire threshold surface remarkably reduces the risk of slipping, as compared with thresholds made of sheet metal. The mat silver coated profile is an impressive surface option which is commonly used in homes as well. It goes well with a number of flooring shades.

The slightly curved threshold is also suitable for a level dif-ference of a couple of centimetres. The profile thickness is 5 mm and total height 10 mm.The silver-anodised option is available for 250 mm fire thresholds.

NEW PRODUCT

Width/type Colour Length Product code

S/O

250 mm, fire threshold Silver-anodised 270 cm GE-AA0002 O


Width/type Length Product code S/O

level difference 4.5 mm, ridged edges, with holes, width 32 mm 300 cm 7092205 S

level difference 0–12 mm, curved surface, without holes, width 40 mm

300 cm 7090405-R S

level difference 8–15 mm, curved surface, without holes, width 50 mm

300 cm 7090905-R S

level difference 0–12 mm, aluminium/stainless steel, without holes, width 40 mm

270 cm B3 AS 270-R S



RAMPS WITH LEVEL DIFFERENCE

NEW PRODUCT

Wide ramps even out the level difference of different materials in renovation objects in particular, and save renovation time and costs. The ramps are designed to make the traffic easier in public premises and facilities. Length 270 mm.

Type Colour Length Product code

S/O

Ramp 1 Aluminium 270 cm 2062309 O

Ramp 2 Aluminium 270 cm 2062101 O

Ramp 3 Silver-anodised aluminium 270 cm 5502290 O





Ramp 12062309 Aluminium

Ramp 22062101 Aluminium

Ramp 35502290 Silver-anodised aluminium





END PROFILES

E7 OAK 270oak

E7 SI 270silver

E7 WH 270white

The end profile with a bottom rail is ideal for joining the floating floors and the threshold. It is also used instead of the skirting by the wall with floating floors.

The profile package contains two bottom rails of unequal height. Of the bottom rails, the higher is used with parquet and the lower with laminate.

End profile with a bot-tom rail

Length Product code

S/O

White 7–18 mm 270 cm E7 WH 270 S

Silver 7–18 mm 270 cm E7 SI 270 S

Oak 7–18 mm 270 cm E7 OAK 270 S


END PROFILES FOR TILES AND CARPETS

Coloured end pro-files

Height Length Product code

S/O

White 6 mm 250 cm 13110 O




White 10 mm 250 cm 13310 O

White 10 mm 300 cm 17310 O

White 12.5 mm 250 cm 13410 O

White 12.5 mm 300 cm 17410 O

Light grey 6 mm 250 cm 13140 O





Light grey 12.5 mm 250 cm 13440 O

Black 6 mm 250 cm 13130 O

Black 8 mm 250 cm 13230 O

Black 12.5 mm 250 cm 13430 O

Black 10 mm 250 cm 13330 O

Stainless steel 3 mm 250 cm E30 S

Stainless steel 4.5 mm 250 cm E45 S







Bendable end profiles Height Length Product code

S/O

Brass 3 mm 250 cm 12003 O

Brass 4.5 mm 250 cm 12053 O



Brass 10 mm 250 cm 12303 O

Brass 12.5 mm 250 cm 12403 O

Brass 15 mm 250 cm 12503 O

Aluminium 3 mm 250 cm 13003 O

Aluminium 4.5 mm 250 cm 13053 O




Aluminium 12.5 mm 250 cm 13403 O


Stainless steel 3 mm 250 cm 14003 O

Stainless steel 4.5 mm 250 cm 14053 O




Stainless steel 12.5 mm 250 cm 14403 O

Bending rolls 9800 O


PLEASE FIND READY-MADE EXPANSION JOINT PROFILES ON PAGE 26!


STAIR EDGE PROFILES FOR HARD USE IN PUBLIC PREMISESDionePro stair edge profiles are an impressive solution for public prem-ises. They are well suited to shopping centres, airports, hotels, offices, hospitals, and stairways in other public premises, for example.

Another option is a stair edge profile with LEDs fit for cinemas and res-taurants, for example.

STAINLESS STEEL STAIR EDGE PROFILES


35 x 25 mm, smooth surface 300 cm 7352505-R S

40 x 25 mm, embossed surface 250 cm 7352605-R S

42.5 x 23.5 mm, grooved surface 300 cm 7523105-R S




Different roughening options for stair edge profiles reduce the risk of slipping in the stairways of public premises.

Grooved surface

Smooth surface Embossed surface


BC1-25 18 LR1-25 19 MC1-25 06

MOUNTING OF STAIR EDGE PROFILESWITH ANTISLIP INSERTSIN PUBLIC PREMISESThe profiles are attached to stairsteps with assembly glue. They can also be mounted with screws through countersank holes drilled in the profile at the installation stage. Screwheads are covered with caps (delivered with profiles in accordance with your order).

POLISHED BRASS STAIR EDGE PROFILES WITH ANTISLIP INSERTS

Available with black or brown antislip inserts.Order codes for colours: black 01, brown 11.

Stair edge/type Length Product code S/O

62.5 x 29 mm, polished brass 300 cm BC1-25 18 O

56 x 50 mm, polished brass 300 cm LR1-25 19 O

52.5 x 29 mm, polished brass 300 cm MC1-25 06 O



C2-25 09 R1-25 14

T1-25 16D1-25 11

M1-25 15 E1-25 08 B1-25 00 07

F1-25 07

E2-25 10

STAIR EDGE PROFILES MADE OF BRUSHED ALUMINIUM

Stair edge profiles can be provided with black or brown antislip inserts.Order codes for colours: black 01, brown 11.


87.5 x 45 mm, brushed aluminium 300 cm E2-25 10 O

87.5 x 28.5 mm, brushed aluminium 300 cm C2-25 09 O

52.5 x 35 mm, brushed aluminium 300 cm D1-25 11 O

54 x 30 mm, brushed aluminium 300 cm M1-25 15 O

56.5 x 51 mm, brushed aluminium 300 cm R1-25 14 O

55 x 40 mm, brushed aluminium 300 cm T1-25 16 O

51.5 x 50 mm, brushed aluminium 300 cm E1-25 08 O

61 x 50 mm, brushed aluminium 300 cm F1-25 07 O

67 x 27 mm, brushed aluminium 300 cm B1 25 06 O



BC1-25 18 LR1-25 19

STAIR EDGE PROFILES MADE OF SILVER-ANODISED ALUMINIUM


67 x 27 mm, silver-anodised aluminium 300 cm B1-25 00 07 O


Made of silver-anodised aluminium. Colour options for antislip inserts: black, grey, brown, blue, red, yellow and green.

STAIR EDGE PROFILES WITH LEDSThe stair edge profiles with LEDs are excellently suited to cinemas and restaurants, for example. Their antislip inserts and frames are black in colour. Colour options for the transparent plastic casing: colourless, blue or red. The LEDs are located at intervals of 5, 10 or 20 cm. Delivered with a transformer to be connected to the network. Separate end pieces are available for the profiles.


77 x 41.5 mm, stair edge profile with LEDs 300 cm BAL7-05 04 98 O

92 x 41.5 mm, stair edge profile with LEDs 300 cm BAL7B-05 01 98 O



8T-22 02 40 7T-22 09 40

B3-24 04 99

STAIR EDGE PROFILES MADE OF UNTREATED ALUMINIUM

Stair edge/type Length Product code

S/O

100 x 32 mm, untreated aluminium 300 cm 8T-22 02 40 O

78 x 33 mm, untreated aluminium 300 cm 7T-22 09 40 O


FOR EXTREMELY HARD

WEAR AND TEAR

STAINLESS STEEL STAIR EDGE PROFILE S= 4.5 mm


55 x 40 mm, stainless steel 250 cm B3-24 04 99 O


Fit for extremely hard terminal use, such as in the corners of the most frequently used stairways at underground stations.

Mounting with screws or separate casting fasteners directly on the casting is possible.


AA109 AA113 AA114

AA115 AA116 AA201

AA202

AA203 AA204

AA205 AA206

TREDSAFE-ANTISLIP STAIR EDGE PROFILES- safety is vital to us and the end result has never looked so good as this!

NEW PRODUCT

Slipping on the stairs is very common and its consequences are all too often serious. New Tredsafe antislip stair edge profiles prevent people from slipping very efficiently. The antislip inserts are made of highly durable polyurethane-coated quartz/vinyl compound.

The pyramidal antislip surface rules slipping out in every direction at an angle of 360 degrees, ensuring that every step taken is safe. As the surface structure removes water efficiently, it is the only safe antislip solution that functions well in wet conditions as well.

Stair edge profiles, thickness 2 mm


AA123AA345

AA 122 AA 125 AA 207

Stair edge profiles for textile carpets, thickness 3.7 mm

Stair edge profiles for textile car-pets, thickness 5 mm:

Stair edge profiles for tiles, thickness 12 mm:

Tredsafe profiles provide ideal protection against slipping in indoor and outdoor areas! In addition to 20 antislip colour options, the selection includes very impressive self-luminous antislip inserts.

The Tredsafe profiles have a silver-anodised coating, which makes them well suited to public premises.

Burgundy/brown Jade greenNeutral black Brown Medium grey Putty Light greyCoal-black

White Blue Bright blue Bright green Burgundy/red Yellow Antislip insert with safety colouring

The Tredsafe stair edge profiles are designed for challenging premises that set special requirements for finish and safety:

• hotels

• shopping centres

• airports

• hospitals

• public means of transport

• theatres

• homes

The antislip inserts with orange/black safety colours are designed to offer the best possible visibility across the edge of the step.

A perfect safety solution for bus-ses, trains and trams that call for the best possible antislip ability and have steps that must be discerned as clearly as possible. Helps visually dis-abled and elderly people discern the edge of the step.


The self-luminous antislip inserts are as safe and durable as the Tredsafe profiles.

There are two options to choose from in antislip products: en-tirely self-luminous antislips and antislips with a self-luminous front edge. They are made with the latest phosphorous technol-ogy and illuminate no less than ten times longer in the dark, as compared with previous self-luminous guide models.

Applications include all challenging objects in public premises that require additional illumination in the stairways in case of emergency.

STAIR EDGE PROFILES WITH SELF-LUMINOUS ANTISLIPS

NEW PRODUCT

The quartz/vinyl antislip inserts are coated with polypropene.

The Super Night Glow self-luminous antislip inserts developed in Japan illuminate ten times longer than normal self-luminous pig-ments!

Object Product Quantity Product code

Village Cinema, Singapore Putty Zebron 980 m AA123

Village Cinema, Singapore Black Zebron 450 m AA123

Waikato Hospital, New Zealand Black Zebron 350 m AA201

Otago Stadium, New Zealand Yellow with safety yellow insert 3,500 m UP117

Paris Stadium, France Light Grey Insert 8,000 m AA122

ACC Housing, New Zealand Super Night Glow Insert 500 homes AA139


Examples of reference projects:

All profile models displayed on page 17 and 18 can be provided with self-luminous antislip inserts.

Reddish-brownJade greenBright green BrownPuttyWhite Burgundy/red

YellowNeutral black Medium grey Light greyCoal-black Bright blueBlue

Fluorising


TILING PROFILESTiling profiles protect outer tiling corners, keep them cleaner and cover tiling edges. The tiling profiles save time and make tiling work easier.

Material: made of stainless steel suitable for public premises.Installation: the profile is pressed on the mounting mortar when outer corner tiles are installed.Cutting: profiles are shortened with a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder. A small number of profiles can be shortened with a hacksaw.Applications: offices, hotels, schools, shopping centres and outer tiling corners in other public premises.


Round model

Stainless steel H=6 mm 250 cm (300 cm) 6530-RST (58100) S/O

Stainless steel H=6 mm, ground 250 cm (300 cm) 54116 (58100) O

Stainless steel H=6 mm, glossy 250 cm (300 cm) 54130 (58130) O

Stainless steel H=8 mm 250 cm (300 cm) 6534-RST (58200) S/O



Stainless steel H=10 mm 250 cm (300 cm) 6535-RST (58300) S

Stainless steel H=10 mm, ground 250 cm (300 cm) 6535-RST HI (58316) S/O


Stainless steel H=11 mm 250 cm (300 cm) 54350 (58350) O



Stainless steel H=12.5 mm 250 cm (300 cm) 6570-RST (58400) S/O

Stainless steel H=12.5 mm, ground 250 cm (300 cm) 54416 (58416) O

Stainless steel H=12.5 mm, glossy 250 cm (300 cm) 54430 (58430) O

Stainless steel H=15 mm 250 cm (300 cm) 54500 (58500) O

Inner corner for 6535 profile, type 6535-IC

6535-IC S

Outer corner for 6535 profile, type 6535-OC

6535-OC S

Square model

Stainless steel H=8 mm, glossy 250 cm 6550 S

Stainless steel H=8 mm, ground 250 cm 14245 O


Stainless steel H=10 mm, ground 250 cm 14365 O

Stainless steel H=12.5 mm, glossy 250 cm 6560 S

Stainless steel H=12.5 mm, ground 250 cm 14465 O


Stainless steel H=22 mm, glossy 250 cm 526808 O

Square model for hard use

Stainless steel H=10 mm 250 cm E 20-10 S

Coloured aluminium, round model

White H=6 mm 250 cm (300 cm) 53110 (57110) O

White H=8 mm 250 cm (300 cm) 53210 (57210) O

White H=10 mm 250 cm (300 cm) 53310 (57310) O

White H=12.5 mm 250 cm (300 cm) 53415 (57410) O

White H=15 mm 250 cm (300 cm) 53510 (57510) O

Light grey H=6 mm 250 cm (300 cm) 53140 (57140) O




Order products (O) are delivered in full consignments of 10 pcs.

Outer and inner corner pieces are available on order to nearly all models! Please consult our sales department for additional information.

Round model

Square model

Coloured model

Round tiling profiles come in lengths of 250 and 300 cm. (The code in brackets is for the length of 300 cm).


TILING STAIR EDGE PROFILES


Beige, H=8 mm 250 cm (300 cm) 80220 (89220) O

Beige, H=11 mm 250 cm (300 cm) 80420 (89420) O

Beige, H=12 mm 250 cm (300 cm) 80620 (89620) O

Brown, H=8 mm 250 cm (300 cm) 80250 (89250) O

Brown, H=11 mm 250 cm (300 cm) 80450 (89450) O

Brown, H=12 mm 250 cm (300 cm) 80650 (89650) O

Grey, H=8 mm 250 cm (300 cm) 80240 (89240) O

Grey, H=11 mm 250 cm (300 cm) 6590-harmaa (89440) S/O

Grey, H=12 mm 250 cm (300 cm) 80640 (89640) O

Black, H=8 mm 250 cm (300 cm) 80230 (89230) O

Black, H=11 mm 250 cm (300 cm) 6590-black (89440) S/O

Black, H=12 mm 250 cm (300 cm) 80630 (89630) O


Order products (O) are sold in full consignments of 10 pcs.

The code in brackets is for the length of 300 cm.

Rubber-rimmed stair edge profiles prevent people from slipping in the stairways.

NEW PRODUCT

TILING EDGE TRIMS


Stainless steel, bright, H=8 mm

250 cm (300 cm) 54600 (58600) O

Stainless steel, brushed, H=8 mm

250 cm (300 cm) 54615 (58615) O


250 cm (300 cm) 54700 (58700) O


250 cm (300 cm) 54715 (58715) O


250 cm (300 cm) 54800 (58800) O


250 cm (300 cm) 54815 (58815) O



Material: made of bright annealed or ground stain-less steel suitable for public premises. Material thickness 1.0 mm.Fastening: profiles are fastened with Elasticfix tape. The profile's pre-installed adhesive tape saves installation time and the costs. The backing of the adhesive tape is removed and the profile is pressed in place. If the outer corner is not straight, glue must be used as an additional reinforcement.

STAINLESS STEEL CORNER PROFILESCutting: profiles are shortened with a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder. A small number of profiles can be cut with a hacksaw.Applications:offices, hotels, schools, shopping centres and outer corners in other public premises.Other materials: Corner protection profiles, size 30 x 30 mm, are also available in aluminium (colours: silver-an-odised, white, beech, cherry, light cherry, oak, wenge and walnut).


S/O

20 x 20 mm, ground surface 270 cm B20 RST 270 S

20 x 20 mm, bright annealed surface 300 cm 7300135 S



30 x 30 mm, aluminium/stainless steel

270 cm B8 AS 270 S

30 x 30 mm, ground surface 300 cm 7303335 S


40 x 40 mm, ground surface 300 cm 7300000 O

40 x 40 mm, bright annealed surface 300 cm 7300002 O


50 x 50 mm, ground surface 300 cm 7333335 S







100 x 100 mm, bright annealed surface

300 cm 7300008 O


PROTECT AGAINST DENTS

AND WEAR AND TEAR

Material: stove-enamelled, anodised or wood imitation coated aluminium. Profile length: 300 cm (wood imitation coated: 270 cm).Fastening: profiles are fastened with Elasticfix tape. The profile's pre-installed ad-hesive tape saves installation time and the costs. The backing of the adhesive tape is removed and the profile is pressed in place. If the outer corner is not straight, glue must be used as an additional reinforcement.Cutting: profiles are shortened with a hacksaw or circular saw.Applications: offices, hotels, schools, shopping centres and outer corners in other public premises.


30 x 30 mm, oak 270 cm B8 TA 270 S

30 x 30 mm, beech 270 cm B8 PY 270 S

30 x 30 mm, walnut 270 cm B8 PH 270 S

30 x 30 mm, cherry 270 cm B8 KI 270 S

30 x 30 mm, light cherry 270 cm B8 VKI 270 S

30 x 30 mm, wenge 270 cm B8 WE 270 S

30 x 30 mm, white 300 cm 7303031-W S

30 x 30 mm, silver-anodised 300 cm 7303032 S


ALUMINIUM CORNER PROTECTION PROFILES

PROFILES FOR PUBLIC PREMISES www.dionepro.fi 23PROTECT AGAINST DENTS

AND WEAR AND TEAR

METAL SKIRTINGSMetal skirtings are an inexpensive and easy option for ground stainless steel profiles. Elegant column collar skirtings are made to order from L-shaped skirtings.

Material: made of stainless steel or aluminium suitable for public premises.Installation: profiles are fastened with glue, mounting clips or bottom profiles.Cutting: profiles are shortened with a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder. A small number of profiles and aluminium skirtings can be shortened with a hacksaw.Applications: offices, hotels, schools, shopping centres and objects in other public premises.


Stainless steel

40 x 10 mm, L model, ground stainless steel 300 cm JL RST 40 Hi 0.8 S

60 x 10 mm, L model, ground stainless steel 300 cm JL RST 60 Hi 0.8 S

40 x 10 mm, clip-mounted model, ground stainless steel

300 cm JL RST 40-JOHTO S

Outside corner for JL RST 40-JOHTO profile RST -Johto U-Kulma S

End piece, left, for JL RST 40-JOHTO profile RST-Johto V-pääty S

End piece, left, for JL RST 40-JOHTO profile RST-Johto O-pääty S

ALUMINIUM

40 x 12 mm, LJ model, silver-anodised 300 cm JL SI 40 S

40 x 12 mm, LJ model, stainless steel anodised

300 cm JL AS 40 S

40 x 12 mm, LJ model, graphite-anodised 300 cm JL NG 40 S

60 x 12 mm, LJ model, silver-anodised 300 cm JL SI 60 S

60 x 12 mm, LJ model, stainless steel anodised

300 cm JL AS 60 S

60 x 12 mm, LJ model, graphite-anodised 300 cm JL NG 60 S

45 x 16 mm, beam model, silver-anodised 250 cm CS1 SI 250 S

45 x 16 mm, beam model, white 250 cm CS1 WH 250 S

60 x 16 mm, beam model, silver-anodised 250 cm CS2 SI 250 S

60 x 16 mm, beam model, white 250 cm SC2 WH 250 S


Aluminium, beam model

L model, stainless steel Clip-mounted model, stainless steel

Aluminium, LJ model


COLUMN COLLARSMaterial: made of stainless steel or brass suitable for public prem-ises. Always manufactured on order in accordance with the reported diameter. Material thickness 0.8 mm or 1.5 mm.Cutting:the assembly margin of the other half is shortened to size accurately by using a hacksaw, or a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder.Installation: profiles are fastened with glue using a tightening line.Applications: offices, hotels, schools, shopping centres and objects in other public premises.

Width/type Product code S/O

more than 200 mm, height: 40–150 mm, ground stainless steel, 2-part

JLRST 300 * O

more than 200 mm, height: 40–150 mm, ground brass, 2-part JLMS 300 * O

less than 200 mm, height: 40–150 mm, ground stainless steel, 4-part

JLRST 200 * O

less than 200 mm, height: 40–150 mm, ground brass, 4-part JLMS 200 * O

*Accurate height and diameter dimensions must be notified when ordering the products. The width of the bottom flange in the two-part collar is always 10 mm but 15–40 mm in the 4-part collar at the customer's option.


2-part and 4-part col-umn collars


CURVED PROFILESCurved cover strips are used in points where the floor surface mate-rial changes to provide the floor with impressive details. Regular curves are bent in accordance with a radius. If the radius is irregular, an accurate model must be prepared and the strip bent in accor-dance with it.

Material: made of ground stainless steel or brasssuitable for public premises. Material thickness 1.5 mm. Bending a variety of extruded brass profiles to a curve is also possible.Consult our sales department for more informa-tion about the bending of profiles.Fastening:countersunk holes are drilled to the profiles at the installation stage and the profiles are fastened with suitable screws.Cutting: both ends of all profiles have a 10 cm un-bent section that is shortened from the most suitable point before fastening the profiles.The profiles are shortened with a hacksaw or a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder.

The minimum bending radii for cover strips to be bent* S/O

GROUND BRASS or STAINLESS STEEL

Profile width 30 mm - minimum bending radius R=300 O



EXTRUDED BRASS




*The minimum radii for edge and stair edge profiles vary case by case. Please consult our sales department for additional information!

Applications: offices, hotels, schools, shopping centres and objects in other public premises. In addition to standard pro-files, we make a number of custom-made profiles, such as bathroom thresholds, inside and outside corner protection pro-files with different angles, as well as cover strips and skirtings of different size and design.

CUSTOM-MADE PRODUCTSMaterial: made of ground or glossy steel or brass suitable for public premises.Edge grinding: grinding profile edges at the manufacturing stage removes the sharp edges caused by the cutting of profiles.Examples: in addition to standard profiles, we make a wide variety of custom-made pro-files, such as bathroom thresholds, inside and outside corner strips with different angles, and cover strips and skirtings of different size and design.Cutting:profiles are cut with a hacksaw or shortened with a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder.Applications: offices, hotels, schools, shopping centres and objects in other public premises.

Custom-made thresholds

Custom-made corner protection profiles

Custom-made cover strips and skirtings


EXPANSION JOINT PROFILESFOR FLOORING MATERIALSThe expansion joint profile covers the expansion joint between two floorings.

Material: made of stainless steel suitable for public premises.Installation:profiles are mounted in connection with installation at the point where the expansion joint is.Cutting: profiles are shortened with a wheel fit for cutting stainless steel. The wheel is attached to an angle grinder. A small number of profiles can be shortened with a hacksaw.Applications: offices, hotels, schools, shopping centres and flooring expansion joints in other public premises.


Flooring expansion joint, L model H=3 mm 250 cm E 30 S

Flooring expansion joint, L model H=4.5 mm 250 cm E 45 S




Flooring expansion joint, L model H=12.5 mm 250 cm E 125 S


Ready-made expansion joint profile with a rubber, H=10 mm, aluminium

250 cm LS 100 AL GREY S

Ready-made expansion joint profile with a rubber, H=8 mm, stainless steel

250 cm LS 80 RST GREY O

Ready-made expansion joint profile with a rubber, H=10 mm, stainless steel


Ready-made expansion joint profile with a rubber, H=12.5 mm, stainless steel




LL1 Grey 300 cm 0393023 O

LL1 Black 300 cm 0393009 O

LL2 Grey 300 cm 0346029 O

LL2 Black 300 cm 0346005 O

LL3 Grey 300 cm 0393320 O

LL4 Grey 300 cm 0342427 O

LL5 Grey 300 cm 0315025 O

LL6 Grey 300 cm 0316022 O


Expansion joint profile, aluminiumExpansion joint profile LL1

Expansion joint profile LL2 Expansion joint profile LL3 Expansion joint profile LL4

Expansion joint profile LL5 Expansion joint profile LL6 Expansion joint profile, L model

Expansion joint profile, stainless steel


STRUCTURAL EXPANSION JOINT PROFILESProviding the expansion joint between surface casting and flooring with one profile only saves time and costs. The use of expansion joint profiles makes it possible to avoid expensive expansion joint repairs under warran-ty and provide the flooring with an impressive looking expansion joint.

Model Clearance Cover width

Structural width

Totalheight

Structural expan-sion jointwidth, max

BS 2 5000 1 14 mm (-7 mm, +7 mm) 55 mm 40 mm 190 mm 55 mm

GTA-N 2 1022 1 10 mm (-5 mm, +5 mm) 75 mm 22 mm 200 mm 50 mm

GTA-N 2 1040 1 10 mm (-5 mm, +5 mm) approx. 75 mm

40 mm 200 mm 50 mm

EX 10 mm (-5 mm, +5 mm) 30 mm 84 mm acc. to need*

50 mm

*to be specified within 30–100 mm

EXLoad endurance: light lorries with a maximum total weight of 3 tons. Unsuitable for premises where hard-wheeled pallet jacks are used.Material: ground stainless steel (S= 1.0 mm). The seal is made of flexible and durable plastic.Seal colours:grey and black. Also available with an oil-proof nitrite rubber. Length 3 m.Installation: a bed of mortar is spread on both sides under the expansion joint profile to make it possible to adjust the final height of the profile's upper edge. The profile is pressed on the mortar bed. After the mortar bed has hardened, the profile is mounted on the floor with bolts at intervals of 40 cm. The surface mortar's upper edge is left as much below the profile's top edge as the surface material requires so that the final surface material is flush with the profile's edge.Applications:expansion joints of floor structures in points that require an impressive looking expansion joint profile placed at exactly the correct height.

GTA -NMaterial and load endurance: frame is totally made of extruded aluminium. Withstands the load generated by light vans with a total weight of 1.5 tons. In addition, it withstands the load generated by shopping trolleys (the maximum weight of trolleys with plastic wheels is 500 kg). Not recommended for points where pallet jacks are used.Installation: a bed of mortar is spread on both sides under the expansion joint profile to make it possible to adjust the final height of the profile's upper edge. The profile is pressed on the mortar bed. After the mortar bed has hardened, the profile is mounted on the floor with bolts at intervals of 40 cm. The surface mortar's upper edge is left as much below the profile's top edge as the surface material requires so that the final surface material is flush with the profile's edge.Applications: expansion joints of floor structures in shopping centres and other objects subject to hard wear and tear.

BSMaterial and load endurance: frame is made of extruded aluminium. The seal is made of flex-ible and durable plastic. Seal colours: light grey, black and brown. Length 5 m. Withstands the load generated by light lorries with a maximum total weight of 3 tons. Unsuitable for premises where hard-wheeled pallet jacks are used.Installation:a bed of mortar is spread on both sides under the expansion joint profile to make it possible to adjust the final height of the profile's upper edge. The profile is pressed on the mortar bed. After the mortar bed has hardened, the profile is mounted on the floor with bolts at intervals of 40 cm. The surface mortar's upper edge is left as much below the profile's upper edge as the surface material requires so that the final surface material is flush with the profile's edge.Applications: expansion joints of floor structures. The profile is provided with a large clearance and its structure is durable.


RO Material and load endurance: thick aluminium profile, withstands the load generated by lorries, industrial trucks and pallet jacks. Installation:both profile edges must be mounted on the floor with epoxide resin across the width of 100 mm to allow the profile to remain in place in hard use. The profile is efficiently pressed onto epoxide resin and the substance is allowed to harden entirely. The height of the flooring and the casting must be taken into account at the installation stage to enable the profile surface to be mounted flush with the flooring. Then the profile is fastened in place with at least 10 mm stress-resistant bolts at intervals of 300 mm. Applications: expansion joints of the floors in shops, fair centres, warehouses and airports. Withstands heavy use and suitable for challenging objects in public premises.

TBGMaterial and load endurance: aluminium profile, withstands the load generated by passenger cars, industrial trucks and light lorries with a maximum total weight of 3 tons and the wheel diameter of 300 mm. Installation: a mortar bed with a width of about 10 cm is spread on both sides of the expansion joints. The thickness of the mortar bed determines the final height of the profile. The profile is pressed on the mortar. After the mortar has hardened, horizontal profile sections are mounted in place with bolts at intervals of about 30 cm.Applications: Industrial premises and parking halls.

BL

Material and load endurance: the aluminium profile withstands the load generated by passenger cars and light lorries with a maximum total weight of 3 tons. Unsuitable flooring material for objects where industrial trucks or pallet jacks are used.Installation:a mortar bed with a width of about 10 cm is spread on both sides of the expansion joints. The thickness of the mortar bed determines the final height of the profile. The profile is pressed on the mortar. After the mortar has hardened, horizontal sections of the profile are mounted in place with bolts at intervals of about 40 cm.Applications: offices and public buildings.

Model Clearance Cover width

Total width

Structural height

Max. structural expansion joint width

S/O

RO 2 0500 2 6 mm (-3 mm, +3 mm) 65 mm 155 mm 40 or 50 mm 50 mm O

RO 2 0800 2 10 mm (-5 mm, +5 mm) 85 mm 175 mm 40 or 50 mm 80 mm O

RO 2 1000 2 15 mm (-7.5 mm, +7.5 mm) 105 mm 195 mm 40 or 50 mm 100 mm O

TBG 2 5030 4 8 mm (-4 mm, +4 mm) 42 mm 110 mm 20 mm 30 mm O

TBG 2 5035 4 8 mm (-4 mm, +4 mm) 42 mm 110 mm 35 mm 30 mm O

BL 2 2900 1 10 mm (-5 mm, +5 mm) 28 mm 125 mm 40 mm 30 mm O


www.dionepro.fi 29ENTRANCE CARPETS WITH ALUMINIUM FRAME

NEW PRODUCT

The first impression of the whole building depends on its vestibule. A modern and quality entrance car-pet in the vestibule provides the building with an up-to-date look, saves cleaning costs and extends the life of the surrounding floor.

Sturdy and long-lasting aluminium-frame vesti-bule carpet with high-quality and durable bristles. Is durable and retains its shape when rolled up for cleaning.

Long-lasting, shape-retaining and soil-repellent bristles are made of the best possible raw materials.

The rubber pieces attached to the aluminium rails attenuate noise and efficiently keep the carpet in place.

Our carpets conform to fire resistance standards EN 11925-2 and EN 9239-1.

ENTRANCE CARPETS WITH ALUMINIUM FRAME

Surface options:

Made to order. Several colour alternatives available for each surface option. Cut-to-shape carpets are also available. Please consult our sales department for additional information.

Grooved rubber Rough fibre ribbon Bristle



INSPECTION AND ACCESS HATCHESThe DionePro access covers on the floor offer a number of significant benefits. The product set durability is ensured with load endurance certification and quality control. Water and gas-proof hatches are safe and enable their installa-tion in challenging applications as well. The fire protection system of DionePro hatches ensures a 90-minute fire endurance time, for instance, for the BV-F90 hatch in accordance with the official IBS fire-endurance test.

Durable and high-quality opening handles, locking mechanisms, spring sys-tems and corner shapes emphasise the user-friendliness and strong quality of our inspection and access hatches.

INSPECTION AND ACCESS HATCHES 32 www.dionepro.fi

WALL AND CEILING COVER PLATESDionePro cover plates can be mounted on the walls or ceilings. Steel covers are white-painted and glossy. Cover plates are protected against scratching with a transparent protective film. The film is easy to detach at the installa-tion stage.

- Rounded and trimmed edges

- Mounting holes in corners, diameter 4 mm

- Colour: matt white

COVER PLATES

Model Size (mm) Thickness (mm) Colour Weight (kg) Package size S/O

PL 140 200 x 200 x 0.8 mm 0.8 mm White 0.26 kg 10 S






INSPECTION AND ACCESS HATCHES www.dionepro.fi 33

NEW INSPECTION DOOR SET DESIGNED FOR WALLS AND CEILINGS

Our DionePro hatch selection includes new inspection door options designed for walls and ceilings. Four models with different properties are available and come in several sizes.

Basic steel-made wall-mounted inspection doors with white surface painting differ from the options on the market due to their new round edge design. They are best suited to conspicuous locations in which the highest possible requirements are set for the hatch appearance and finish. The selection includes impressive, thermally insulated inspection doors made of ground aluminium as well.

Other models include inspection doors that are made of steel, primed white and fire-proof, or inspection doors that are fire-proof and thermally insulated.

NEW PRODUCT

Illustrations: 1. Steel inspection door with round edges (left top edge), 2. Thermally insulated aluminium inspection door (right top edge)3. Fire-proof steel inspection door (left bottom edge) 4. Fire-proof thermally insulated inspection door (right bottom edge).


THERMALLY INSULATED INSPECTION DOORLT-314, LT-467

Applications• Suitable for all wall surfaces in indoor and outdoor use.Properties:• The cover is provided with a thermally insulated plate.• Concealed hingeMaterial: • Light-structured, untreated aluminium with brushed surface.• The frame is equipped with a seal.• The lock can be opened with a screwdriver.

THERMALLY INSULATED INSPECTION DOORS

Model Type Hatch size Installation opening size Weight S/O

LT-314 Thermally insulated inspection door

305 x 305 mm 314 x 314 mm 1.8 kg S

LT-467 Thermally insulated inspection door

457 x 457 mm 467 x 467 mm 2.7 kg S

S = IN STOCK O= ORDER PRODUCT

INSPECTION DOOR

INSPECTION DOORS

Model Hatch size Installation opening size

Weight (kg)

S/O

UF-158 152 x 152 mm 157 x 157 mm 0.68 kg S

UF-208 203 x 203 mm 208 x 208 mm 0.91 kg S

UF-310 305 x 305 mm 310 x 310 mm 1.14 kg S

UF-386 381 x 381 mm 386 x 386 mm 2.50 kg S

UF-462 457 x 457 mm 462 x 462 mm 3.41 kg S

UF-615 610 x 610 mm 615 x 615 mm 5.45 kg S


Applications• Suitable for all wall and ceiling surfaces.Properties:• The seamless frame with round corners is made of one part only.• Concealed hingeMaterial• Galvanised steel with white surface painting.• The lock can be opened with a screwdriver.


FW-30890, FW-46090

FIRE-PROOF WALL HATCHFB-30890, FB-46090

Applications• Suitable for all wall surfaces in indoor and outdoor use.• Fire-proof on wall surfaces (90 min).Properties:• Cover provided with a 2.5 cm fire insulation.• Concealed hinge• Self-closing and locking (equipped with a spring).Material: • White, primed steel

• Lockable with a key and openable with a separate fixed opening knob attached to the hatch.• Locking is openable also from inside.

FIRE HATCHES

Model Type Hatch size Installation opening size Weight Fire endur-ance

S/O

FB-30890 Fire-insulated wall-mounted inspection door

305 x 305 mm 308 x 308 mm 3.8 kg 90 min S

FB-46090 Fire-insulated wall-mounted inspection door

457 x 457 mm 460 x 460 mm 6.5 kg 90 min S


FIRE-PROOF WALL-MOUNTED INSPECTION DOOR WITH THERMAL INSULATION

Applications• Suitable for all wall and ceiling surfaces.• Fire-proof on wall surfaces (90 min), fire-retardant on ceiling surfaces.Properties:• Cover provided with a 5 cm fire-proof thermal insulation.• Concealed hinge• Self-closing and locking (equipped with a spring).Material: • White, primed steel

• Lockable with a key or openable with a separate fixed opening knob attached to the hatch.• Locking is openable also from inside.

FIRE HATCHES

Model Type Hatch size Installation opening size Weight Fire endurance S/O

FW-30890 Fire-proof inspection door with thermal insulation

305 x 305 mm 308 x 308 mm 4.8 kg 90 min S

FW-46090 Fire-proof inspection door with thermal insulation

457 x 457 mm 460 x 460 mm 9.1 kg 90 min S



ACCESS COVERS

GALVANISED STEEL

DionePro access covers are gas and water-proof, precision-machined and easy to coat. The access covers come in many sizes and shapes. They are made of aluminium, or stainless and galvanised steel. Thanks to their patented opening mechanism, the manholes are easy to open.

As DionePro access covers are gas and water-proof, they are best suited to inspection doors for well-ventilated base floors, also in radon areas. The access covers are also available as options lined up in rows and used in cable chan-nels of passages, for example.

When cast and coated, basic models withstand the weight of the passenger car. Access covers that withstand the weight generated by heavy vehicles are also available. Stainless steel manholes are suitable for hospitals and food production premises as well.

The fire-endurance time of the cast and coated basic models is about 60 min. In addition, challenging objects can be provided with fire hatches with a fire-endurance time of 90 min.

The emergency hatch to be mounted on the balcony is pro-vided with a ladder that can be released from inside the hatch, or without a ladder.

BALCONY HATCHES

Model Inner measure (cm)

Outer measure (cm)

Weight without ladder (kg)

PL 66 60 x 60 cm 78 x 78 cm 50 kg


Load endurance: 125 kNMaterial: the frame and cover are made of a 2 mm steel profile. The structure is galvanised after welding.Properties: gas and water-proof access cover which is manufactured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the manhole is almost inconspicuous in the flooring after its installation. The reinforcement inside the access cover im-proves structural load endurance.Applications: manholes that must be gas and water-proof in indoor and outdoor use.

BV STEEL ACCESS COVER GAS AND WATER-PROOF

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip

The BV access cover partly covered with tiles.

The BV access cover mounted on the café floor.

The BV access cover, opened and lifting handles in place.

The cross-sectional drawing of the BV access cover

Model Inner measure (cm)C x D

Outer measure (cm)A x B

Weight before fill-ing (kg)

S/O*

BV 33 30 x 30 43.5 x 43.5 10 kg S

BV 44 40 x 40 53.5 x 53.5 13 kg S

BV 45 45 x 45 58.5 x 58.5 16 kg S

BV 55 50 x 50 63.5 x 63.5 17 kg S

BV 64 60 x 40 73.5 x 53.5 17 kg S

BV 66 60 x 60 73.5 x 53.5 21 kg S

BV 635 63.5 x 63.5 77.0 x 77.0 22 kg S

BV 86 80 x 60 93.5 x 73.5 27 kg S

BV 88 80 x 80 93.5 x 93.5 31 kg S

BV 106 100 x 60 113.5 x 73.5 31 kg S

BV 108 100 x 80 113.5 x 93.5 37 kg S

BV 110 100 x 100 113.5 x 113.5 42 kg S



Load endurance: 125 kNMaterial: the frame and cover are made of extruded aluminium, the base is made of aluminium plate.Properties: gas and water-proof access cover which is manufactured with accurate dimensions. Water-proof even under the water pressure of 1000 mm. Thanks to its small corners and accurately dimensioned edge structure, the access cover is almost inconspicuous in the flooring after its installation. Ideal for locations where extremely high requirements are set for the appearance of the access cover’s visible edge. The reinforcement in the access cover improves structural load endurance.Applications: gas and water-proof access cover located indoors when high requirements are set for the appearance of the access cover's visible edges or when the floor must be ground afterwards (e.g. parquet floors).

BV ALUMINIUM ACCESS COVER GAS AND WATER-PROOF

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Base plate8. Corner welding9. Frame

The cross-sectional drawing of the aluminium BV access cover




S/O*

BVA 22 20 x 20 32 x 32 3 kg O

BVA 33 30 x 30 42 x 42 5 kg O

BVA 44 40 x 40 52 x 52 7 kg O

BVA 45 45 x 45 57 x 67 8 kg O

BVA 55 50 x 50 62 x 62 9 kg O

BVA 64 60 x 40 72 x 52 9 kg O

BVA 66 60 x 60 72 x 72 10 kg O

BVA 635 63.5 x 63.5 75.5 x 75.5 11 kg O

BVA 77 70 x 70 82 x 82 12 kg O

BVA 86 80 x 60 92 x 72 12 kg O

BVA 88 80 x 80 92 x 92 15 kg O

BVA 106 100 x 60 112 x 72 15 kg O

BVA 108 100 x 80 112 x 92 21 kg O

BVA 110 100 x 100 112 x 112 23 kg O

Cover depth: 6.6 cm, total structural height: 7.6 cm


The aluminium BV access cover, opened in a textile carpet covered floor.

The aluminium BV access cover, partly covered with tiles.





S/O*

BVA 22 20 x 20 32 x 32 3 kg O

BVA 33 30 x 30 42 x 42 5 kg O

BVA 44 40 x 40 52 x 52 7 kg O

BVA 45 45 x 45 57 x 67 8 kg O

BVA 55 50 x 50 62 x 62 9 kg O

BVA 64 60 x 40 72 x 52 9 kg O

BVA 66 60 x 60 72 x 72 10 kg O

BVA 635 63.5 x 63.5 75.5 x 75.5 11 kg O

BVA 77 70 x 70 82 x 82 12 kg O

BVA 86 80 x 60 92 x 72 12 kg O

BVA 88 80 x 80 92 x 92 15 kg O

BVA 106 100 x 60 112 x 72 15 kg O

BVA 108 100 x 80 112 x 92 21 kg O

BVA 110 100 x 100 112 x 112 23 kg O



BVE STAINLESS STEEL ACCESS COVER GAS AND WATER-PROOFLoad endurance: 125 kNMaterial: made of 2 mm stainless steel (quality 304). The surface is pas-sivated throughout after welding.Properties:gas and water-proof access cover which is manufactured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the manhole is almost inconspicuous in the flooring after its installation. The reinforcement in the manhole improves structural load endurance.Applications: access cover that must be gas and water-proof, extremely corrosion-resistant or hygienic, such as those in food production prem-ises or hospitals.

Access cover made of acid-proof stainless steel (quality 316) are available on order.

The stainless steel BV access cover is suitable for food production premises, for example.


The cross-sectional drawing of the stainless steel BV manhole




S/O*

BVE 33 30 x 30 43.5 x 43.5 9 kg O

BVE 44 40 x 40 53.5 x 53.5 13 kg O

BVE 45 45 x 45 58.5 x 58.5 17 kg O

BVE 55 50 x 50 63.5 x 63.5 17 kg O

BVE 64 60 x 40 73.5 x 53.5 16 kg O

BVE 66 60 x 60 73.5 x 73.5 20 kg O

BVE 86 80 x 60 93.5 x 73.5 24 kg O

BVE 88 80 x 80 93.5 x 93.5 30 kg O

BVE 106 100 x 60 113.5 x 73.5 29 kg O

BVE 108 100 x 80 113.5 x 93.5 33 kg O

BVE 110 100 x 100 113.5 x 113.5 40 kg O

Cover depth: 5 cm, total structural height: 7.5 cm



Load endurance: 15 kN (walking-resistant).Material: the frame and cover edges are made of extruded alumini-um, the base of aluminium plate.Properties: the access cover is well suited to 24 mm surface material at the maximum and prefilled with a light composite plate. The cover structure is lighter than in the manhole with a normal concrete filling. The access cover is gas and water-proof and manufactured with ac-curate dimensions.Thanks to its small corners and accurately dimensioned edge struc-ture, the access cover is almost inconspicuous in the flooring after its installation. Ideal for locations where extremely high requirements are set for the appearance of the access cover’s visible edge.Applications: access cover that must be gas and water-proof in in-door use. To ensure waterproofness, the section between the access cover’s outer edge and the surrounding floor must be insulated with water-proof insulation.

CLA ALUMINIUM ACCESS COVER, PREFILLED WITH A LIGHT COMPOSITE PLATE, WITH A SEAL

1. Frame2. Cover3. Seal4. Locking bolt5. Shield plug6. Composite plate7. Frame joint8. Bolt thread9. Frame

The cross-sectional drawing of the CLA access cover




S/O*

CLA 22 20 x 20 32 x 32 3 kg O

CLA 33 30 x 30 42 x 42 5 kg O

CLA 44 40 x 40 52 x 52 7 kg O

CLA 55 50 x 50 62 x 62 9 kg O

CLA 64 60 x 40 72 x 52 9 kg O

CLA 66 60 x 60 72 x 72 10 kg O

CLA 86 80 x 60 92 x 72 12 kg O

CLA 88 80 x 80 92 x 92 15 kg O

CLA106 100 x 60 112 x 72 15 kg O




CCA ALUMINIUM, HINGED, PREFILLED WITH A LIGHT COMPOSITE PLATE, WITH A SEAL

Load endurance: 15 kN (walking-resistant).Material: the frame and cover edges are made of extruded alu-minium, the base of aluminium plate.Properties: the access cover is well suited to 24 mm surface ma-terials at the maximum and prefilled with a light composite plate. The cover structure is lighter than in the access cover with a nor-mal concrete filling. The access cover is gas and water-proof and manufactured with accurate dimensions. Thanks to its small cor-ners and accurately dimensioned edge structure, the access cover is almost inconspicuous in the flooring after its installation. Ideal for locations where extremely high requirements are set for the appearance of the manhole's visible edge.Applications: access cover that must be gas and water-proof in indoor use. To ensure waterproofness, the section between the access cover's outer edge and the surrounding floor must be insu-lated with water-proof insulation.

1. Frame2. Cover3. Seal4. Locking bolt5. Frame joint6. Shield plug7. Hinge8. Frame joint9. Frame10. Support rod11. Composite plate




S/O*

CCA 55 50 x 50 62 x 64 10 kg O

CCA 66 60 x 60 72 x 74 12 kg O

CCA 86 80 x 60 92 x 74 14 kg O

CCA 88 80 x 80 92 x 94 17 kg O

CCA 106 100 x 60 112 x 74 17 kg O



A cross-sectional drawing of the hinged BV aluminium access cover.

The light, hinged access cover is easy to open.

The support rod keeps the cover open when required.


BV SHALLOW STEEL AND BVE SHALLOW STAINLESS STEEL ACCESS COVER GAS AND WATER-PROOF

Load endurance: 15 kN (walking-resistant).Material: the frame and cover are made of a 2 mm steel profile.The structure is galvanised after welding. The stainless steel product is made of 2 mm stainless steel (quality 304). The surface is passivated throughout after welding.Properties: The manhole cover is manufactured with accurate di-mensions. The cover's total height is only 5 cm.The access cover filled with a thinner surface casting is light to open. The reinforcement inside the manhole improves structural load endurance.Applications: access cover in indoor use.

The reinforced bottom side of the shal-low BV access cover.

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. Reinforced bottom side

The cross-sectional drawing of the shallow BV access cover.




S/O*

GALVANISED STEEL

BV-shallow 22 20 x 20 33 x 33 5 kg O

BV-shallow 30 x 30 43 x 43 8 kg O







BV-shallow 100 x 60 103 x 73 27 kg O

STAINLESS STEEL

BVE-shallow 30 x 30 43 x 43 8 kg O











BV-F90 STEEL ACCESS COVER GAS AND WATER-PROOF FIRE ENDURANCE OF 90 min

Load endurance:125 kNMaterial: the frame and cover are made of a 2 mm steel profile.The structure is galvanised after welding. The access cover is equipped with a fire-protection plate and a fire-resistant special seal.Properties: the fire-resistant, gas and water-proof access cover is manufac-tured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the access cover is almost inconspicuous in the flooring after its installation. The reinforcement inside the access cover improves structural load endurance.Fire-endurance class:the fire endurance time is 90 min after installation and coating. Suitable for objects with high fire safety requirements. The fire protection properties are verified with an official IBS fire-endurance test.Applications: access cover that must be gas and water-proof and require a high fire-endurance class in indoor and outdoor use.

1. Frame2. Cover3. Fire-proof seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. Fire-retardant plate9. Plate lifting ring10. Fire-retardant plate's edge profile The cross-sectional drawing of the fire-retardant access cover.




S/O*

BV-F90 33 30 x 30 43.5 x 43.5 13 kg O

BV-F90 45 45 x 45 58.5 x 58.5 21 kg O

BV-F90 55 50 x 50 63.5 x 63.5 23 kg O

BV-F90 64 60 x 40 73.5 x 53.5 23 kg O

BV-F90 66 60 x 60 73.5 x 73.5 30 kg O

BV-F90 635 63.5 x 63.5 77.0 x 77.0 32 kg O

BV-F90 86 80 x 60 93.5 x 73.5 38 kg O

BV-F90 88 80 x 80 93.5 x 93.5 45 kg O

BV-F90,106 100 x 60 113.5 x 73.5 45 kg O

BV-F90,108 100 x 80 113.5 x 93.5 54 kg O

BV-F90,110 100 x 100 113.5 x 113.5 63 kg O




BVS-250 STEEL MANHOLEFOR HEAVY VEHICLES GAS AND WATER-PROOF

Load endurance: 250 kNMaterial: the frame and cover are made of a steel profile.The structure is galvanised after welding. The manhole is equipped with reinforcement beams to enable heavy use.Properties: gas and water-proof manhole which is manufactured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the manhole is almost inconspicuous in the flooring after its installation. The reinforcement inside the manhole improves structural load endurance.Applications:warehouses and loading platforms where industrial trucks are used.

The BVS-250 access cover’s bottom side is reinforced with I beams.

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. Reinforcement beam

The cross-sectional drawing of the BVS-250 access cover




S/O*

BVS 250/44 40 x 40 53.5 x 53.5 17 kg O

BVS 250/55 50 x 50 63.5 x 63.5 26 kg O

BVS 250/64 60 x 40 73.5 x 73.5 25 kg O

BVS 250/66 60 x 60 73.5 x 73.5 31 kg O

BVS 250/88 80 x 80 93.5 x 93.5 52 kg O

BVS 250/106 100 x 60 113.5 x 73.5 52 kg O

BVS 250/110 100 x 100 113.5 x 113.5 78 kg O

Cover depth: 5 cm, total structural height: 7.5 cmThe structural height is increased with a 10 cm I beam placed at the bottom of the access cover..



The BVS-400 access cover’s bottom side is reinforced with I beams and the framework.

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. The framework for reinforcement beams9. Reinforcement beam

The cross-sectional drawing of the BVA-400 access cover




S/O*

BVS 400/55 50 x 50 63.5 x 71.5 52 kg O

BVS 400/64 60 x 40 73.5 x 61.5 50 kg O

BVS 400/66 60 x 60 73.5 x 81.5 62 kg O

BVS 400/88 80 x 80 93.5 x 101.5 103 kg O

BVS 400/106 100 x 60 113.5 x 81.5 119 kg O

BVS 400/110 100 x 100 113.5 x 121.5 175 kg O

Cover depth: 5 cm, installation height: 18 cm (60 x 60-80 x 80) or 22 cm (100 x 100)


BVS-400 STEEL ACCESS COVERFOR HEAVY VEHICLES GAS AND WATER-PROOF

Load endurance: 400 kNMaterial: the frame and cover are made of a steel pro-file. The structure is galvanised after welding. The access cover is equipped with reinforcement beams and the steel framework to enable heavy use.Properties: gas and water-proof access cover which is manufactured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge struc-ture, the access cover is almost inconspicuous in the flooring after its installation. The reinforcement inside the access cover improves structural load endurance.Applications: factories, warehouses, loading platforms and driving routes. Withstands the load generated by industrial trucks and heavy vehicles.


BV-GD STEEL ACCESS COVER WITH GAS SPRINGS AND BVE-GD STAINLESS STEEL ACCESS COVER WITH GAS SPRINGSGAS AND WATER-PROOFLoad endurance:125 kNMaterial: the frame and cover are made of a 2 mm steel profile. The structure is galvanised after welding. The stainless steel product is made of 2 mm stain-less steel (quality 304). The surface is passivated throughout after welding. The access cover is provided with high-quality gas springs.Properties: gas and water-proof access cover which is manufactured with ac-curate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the access cover is almost inconspicuous in the flooring after its installation.Opening: gas springs that facilitate opening make it possible for one user to open the access cover without much effort.Applications: access cover that must be gas and water-proof in indoor and outdoor use. Ideal for locations where the access covermust be opened very often.Installation:gas springs are attached in place after the access cover has been installed and the concrete has hardened.

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. Gas spring

The cross-sectional drawing of the BVA-250 access cover

The bottom side of the BV-GD access cover..

The BV-GD access cover, installed on a terrace.




S/O* The number of springs

GALVANISED STEEL

BV-GD 66 60 x 60 73.5 x 75.15 29 kg O 1

BV-GD 86 80 x 60 93.5 x 75.15 36 kg O 2

BV-GD 88 80 x 80 93.5 x 95.15 42 kg O 2

BV-GD 106 100 x 60 113.5 x 75.15 40 kg O 2

BV-GD 110 100 x 100 113.5 x 115.15 55 kg O 2

STAINLESS STEEL

BVE-GD 66 60 x 60 73.5 x 75.15 28 kg O 1

BVE-GD 86 80 x 60 93.5 x 75.15 35 kg O 2

BVE-GD 88 80 x 80 93.5 x 95.15 41 kg O 2

BVE-GD 106 100 x 60 113.5 x 75.15 40 kg O 2

BVE-GD 110 100 x 100 113.5 x 115.15 53 kg O 2




Load endurance: 125 kNMaterial: the frame and cover are made of a 2 mm steel profile. The structure is galvanised after welding.Properties: gas and water-proof access cover which is manufactured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the manhole is almost inconspicuous in the flooring after its installation.Opening: gas springs that facilitate opening make it possible for one user to open the access cover without much effort. The lock is opened from above with an Allen key and from below with a handle.Applications: access covers that must be gas and water-proof in in-door and outdoor use. Ideal for locations, such as service pits, where the access cover must be opened very often.Installation: gas springs are attached in place after the access cover has been installed and the concrete has hardened.

BV-GDZ STEEL ACCESS COVER WITH GAS SPRINGSGAS AND WATER-PROOF OPENABLE FROM ABOVE AND BENEATH

Opening the BV-GDZ access cover

The bottom locking system in the BV-GDZ access cover..

The cross-sectional drawing of the BV-GDZ access cover.

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. Gas spring9. Opening handle



Weight before filling (kg)

S/O* The number of springs

BV-GDZ 66 60 x 60 73.5 x 75.15 30 kg O 1

BV-GDZ 86 80 x 60 93.5 x 75.15 38 kg O 2

BV-GDZ 88 80 x 80 93.5 x 95.15 44 kg O 2

BV-GDZ 110 100 x 100 113.5 x 115.15 58 kg O 2

Cover depth: 5 cm, installation height: 18 cm (60 x 60-80 x 80) or 22 cm (100 x 100)



Load endurance: 125 kNMaterial: the frame and cover are made of a 2 mm steel profile. The structure is galvanised after welding.Properties: the gas and water-proof access cover is manufac-tured with accurate dimensions and has a 10 cm cover that can be coated. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the access cover is almost inconspicuous in the flooring after its installation. The reinforcement inside the access cover improves structural load endurance.Applications: access covers that must be gas and water-proof in indoor and outdoor use, when the cover is filled up with bricks, concrete slabs, or yard or street paving stones. Other models that can be filled up with yard paving stones: the easy-to-open BVH-GD MAXI access cover with gas springs and a load endur-ance of 125 kN; the reinforced BVHS 250 steel access cover with a load endurance of 250 kN that withstands the load generated by heavy vehicles; the reinforced BVHS 400 steel access cover with a load endurance of 400 kN that withstands the load generated by heavy vehicles. The cover depth of these models is 10.2 cm; several sizes available.

Please consult our sales department for additional informa-tion!

BVH-MAXI STEEL ACCESS COVERGAS AND WATER-PROOF CAN BE COVERED WITH YARD PAVING STONES

The BV-MAXI access cover, partly filled up with paving stones.

The BV-MAXI access cover in the paving.


The cross-sectional drawing of the BV-MAXI access cover.




S/O*

BVH maxi 44 40 x 40 55.2 x 55.2 22 kg O

BVH maxi 55 50 x 50 65.2 x 65.2 27 kg O

BVH maxi 66 60 x 60 75.2 x 75.2 28 kg O

BVH maxi 86 80 x 60 95.2 x 75.2 35 kg O

BVH maxi 88 80 x 80 95.2 x 95.2 40 kg O

BVH maxi 106 100 x 60 115.2 x 75.2 40 kg O

Cover depth: 10.2 cm, structural height: 12.5 cm



BVH-GD MAXI STEEL ACCESS COVER WITH GAS SPRINGSDEEP COVER CAN BE COATED WITH PAVING STONES




S/O*

BVH-GD maxi 66 60 x 60 75 x 75 52 kg O

BVH-GD maxi 86 80 x 60 95 x 75 60 kg O

BVH-GD maxi 88 80 x 80 95 x 95 64 kg O

BVH-GD maxi 106 100 x 60 115 x 75 65 kg O

Cover depth 10.2 cm, installation height 12.5 cm


Load endurance: 125 kNMaterial: the frame and cover are made of a 2 mm steel profile. The structure is galvanised after welding.Properties:equipped with two gas springs. Easy to open. The gas-proof and almost water-proof access cover is manufactured with accurate dimensions and has a 10 cm cover that can be coated. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the access coveris almost inconspicuous in the flooring after its installation. The reinforcement inside the access cover improves structural load endurance.Applications: access covers that must be gas and water-proof in indoor and outdoor use, when the cover is filled up with bricks, concrete slabs, or yard or street paving stones in objects where the access cover must be easy to open.The cover depth is 10.2 cm; several sizes available. Gas springs are delivered separately and installed in place as the last parts after the access cover has been cast and coated.


Load endurance:15 kN (walking-resistant).Material: the frame and cover are made of a 2 mm steel profile.(45 x 45 mm, 50 x 50 cm and 60 x 60 cm, the access cover made of 3 mm steel). The cover can be used by placing the plate surface up or by turning the cover upside down and coating the chute section. The depth of the coatable casing section: 15 mm. The selection includes manhole options painted on order in RAL tones.Properties: equipped with a seal but it is not entirely gas and water-proof. The 30 x 30 cm access cover is provided with mounting screws. The access cover is opened by lifting it with the screws. Other sizes of manholes are opened with a separate lifting handle. Their delivery does not include mounting screws. If the access cover with the lifting handle is coated, the lifting handle must be embedded in the coat-ing's opening on the other side of the access cover.Applications: access covers in indoor use, when they must be coatable and made of inexpensive sheet metal.Installation: the access cover is fitted in the opening and fastened with screws through the foot part holes in the opening's vertical edge. When necessary, the ac-cess cover can be attached with glue or mortar from the frame to the floor.

HL GALVANISED ACCESS COVER




S/O*

HL SI 33 30 x 30 35.5 x 35.5 3.7 kg S

HL SI 45 45 x 45 50.5 x 50.5 8.7 kg O

HL SI 55 50 x 50 55.5 x 55.5 10.2 kg S

HL SI 66 60 x 60 65.5 x 65.5 12.6 kg S

Structural height: 4.5 cm





S/O*

HL TL 33 30 x 30 35.5 x 35.5 2.9 kg O

HL TL 45 45 x 45 50.5 x 50.5 4.8 kg O

HL TL 55 50 x 50 55.5 x 55.5 7.8 kg O

HL TL 66 60 x 60 65.5 x 65.5 9.2 kg O


Load endurance:15 kN (walking-resistant).Material: the frame is made of a 2 mm steel profile. The cover is made of 3 mm anti-slip riffled plate-coated aluminium.Properties:equipped with a seal but it is not entirely gas and water-proof. The 30 x 30 cm access cover is provided with mounting screws. The manhole is opened by lifting it with the screws. Other sizes of manholes are opened with a separate lifting handle. Their deliv-ery does not include mounting screws.Applications: access covers in indoor use, when they must be made of inexpensive, anti-slip plate. They are available on order with stainless steel frames to allow their use in out-door locations (if turned upside down, the other side can be coated if required).Installation:the access cover is fitted in the opening and fastened with screws through the foot part holes in the opening's vertical edge. When necessary, the manhole can be attached with glue or mortar from the frame to the floor.

HL RIFFLED-PLATE ACCESS COVER

The HL SI 66 manhole with a galvanised plate surface.

The HL SI 33 access cover used upside down and coated with parquet.





S/O*

RVE 22 20 x 20 30.5 x 30.5 6 kg O

RVE 33 30 x 30 40.5 x 40.5 9 kg O

RVE 44 40 x 40 50.5 x 50.5 13 kg O

RVE 55 50 x 50 60.5 x 60.5 15 kg O

RVE 54 60 x 40 70.5 x 50.5 15 kg O

RVE 66 60 x 60 70.5 x 70.5 24 kg O

RVE 86 80 x 60 90.5 x 70.5 30 kg O

RVE 88 80 x 80 90.5 x 90.5 36 kg O

RVE 106 100 x 60 110.5 x 70.5 36 kg O

RVE 110 100 x 100 110.5 x 110.5 54 kg O


Gas and water-proof, stainless steel

Load endurance:15 kNMaterial: the frame, plate and reinforcement are made of stainless steel (quality 304)Properties:gas and water-proof model, flat structure. The special seal withstands chemicals well. The delivery includes an opening tool.Applications: pits in walking areas in buildings or in their neigh-bourhood, especially in objects that require perfect corrosion re-sistance.

RVE-RSTGAS AND WATER-PROOF




S/O*

RV 64 60 x 40 70.5 x 50.5 22 kg O

RV 66 60 x 60 70.5 x 70.5 29 kg O

RV 86 80 x 60 90.5 x 70.5 37 kg O

RV 88 80 x 80 90.5 x 90.5 45 kg O


RV-STEEL ACCESS COVERGAS AND WATER-PROOF

Load endurance:15 kNMaterial:the frame is made of 2 mm cold-formed, galvanised steel that has been profiled with precision tools. The access cover is made of embossed plate.Properties: gas and water-proof model, flat structure. The special seal withstands chemicals well. The delivery includes an opening tool.Applications:pits in walking areas in buildings and their neighbourhood; ideal for maintenance pits.Installation: the access cover must be installed exactly in ac-cordance with its installation instructions. To ensure water-proofness, the access cover’s outer edge must be attached tightly to the floor with casting.


RVA- ALUGAS AND WATER-PROOF.Load endurance:15 kNMaterial: the frame is made of extruded aluminium profile. The bottom side reinforcement is made of aluminium.Properties: gas and water-proof model, flat structure. The special seal with-stands chemicals well. The delivery includes an opening tool.Applications: pits in walking areas in buildings and their neighbourhood, ideal for objects that require corrosion resistance and/or withstand only minor loads.Installation:the manhole must be installed in accordance with its installa-tion instructions. To ensure waterproofness, the manhole's outer edge must be attached tightly to the floor with casting.




S/O*

RVA 33 30 x 30 38.5 x 38.5 3 kg O

RVA 55 50 x 50 58.5 x 58.5 5 kg O

RVA 64 60 x 40 68.5 x 48.5 5 kg O

RVA 66 60 x 60 68.5 x 68.5 8 kg O

RVA 86 80 x 60 88.5 x 68.5 10 kg O

RVA88 80 x 80 88.5 x 88.5 12 kg O

RVA 106 100 x 60 108.5 x 68.5 12 kg O

RVA 110 100 x 100 108.5 x 108.5 18 kg O



Load endurance:15 kN (walking-resistant).Material:the frame and cover are made of a 2 mm stainless steel profile (45 x 45 mm, 50 x 50 cm and 60 x 60 cm; the access cover cover made of 3 mm stainless steel). The cover can be used by placing the plate surface up or by turning the cover upside down and coating the chute section. The depth of the coatable casing section: 15 mm.Properties: equipped with a seal but it is not entirely gas and water-proof. The 30 x 30 cm manhole is provided with mounting screws. The access cover is opened by lifting it with the screws. Other sizes of access coverS are opened with a separate lifting handle. Their delivery does not include mounting screws.If the access covers equipped with the lifting handle is coated, the lift-ing handle must be embedded in the coating on the other side of the access covers.Applications: indoor and outdoor access covers when it is necessary to use a plate-surface manhole or an easy-to-coat stainless steel access covers.Installation: the access cover is fitted in the opening and fastened with screws through the foot part holes in the opening's vertical edge. When necessary, the manhole can be attached with glue or mortar from the frame to the floor.

HL STAINLESS STEEL ACCESS COVER


Outer mea-sure (cm)A x B


S/O*

HL RST 33 30 x 30 35.5 x 35.5 3.7 kg O

HL RST 45 45 x 45 50.5 x 50.5 8.7 kg O

HL RST 55 50 x 50 55.5 x 55.5 10.2 kg O

HL RST 66 60 x 60 65.5 x 65.5 12.6 kg O


Material: galvanised steel after welding.Properties: the access cover is manufactured with accurate dimen-sions and equipped with a ventilation pipe. Hinged model that can be locked with a padlock. The ventilation pipe is provided with an insect net. When open, the manhole can be detached entirely. When necessary, the delivery may include the seal.Applications:wells, containers and water supply plants.Other materials: The BR access cover selection also includes an op-tion made of stainless steel. It is suitable for objects that must be corrosion-resistant (model BRE-D).

BR STEEL ACCESS COVER




S/O*

BR-D 55 49.5 x 49.5 56.5 x 56.5 15 kg O

BR-D 66 59.5 x 59.5 66.5 x 66.5 18 kg O

BR-D 88 79.5 x 79.5 86.5 x 86.5 21 kg O

BRE-D 55 50.0 x 50.0 56.5 x 56.5 12 kg O

BRE-D 66 60.0 x 60.0 66.5 x 66.5 15 kg O

BRE-D 88 80.0 x 80.0 86.5 x 86.5 23 kg O

BRE-*S = IN STOCK O= ORDER PRODUCT The cross-sectional drawing of the BR access cover

1. Frame2. Cover plate3. Seal(accessory)4. Padlock's handle5. Ventilation pipewith an insect net6. Hinge


Load endurance: 125 kNMaterial: the frame and cover are made of a 2 mm steel pro-file. The structure is galvanised after welding. The access cover is equipped with a detachable aluminium-coated thermal in-sulation plate.Properties: gas and water-proof access cover which is manu-factured with accurate dimensions. The conical design and the lift key make it easy to open. Thanks to its small corners and accurately dimensioned edge structure, the access cover is almost inconspicuous in the flooring after its installation. The reinforcement inside the access cover improves structural load endurance.Applications: access cover that must be gas and water-proof in indoor and outdoor use, when special requirements are set for the access cover's thermal insulation ability.Installation:to ensure the best thermal insulation ability for the access cover, the gap between the access cover and the surrounding floor must be sealed with care.

BV THERMO ACCESS COVERGAS AND WATER-PROOF WITH THERMAL INSULATION

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Fastening clip8. Insulation plate9. Opening handle for insulation plate10. Insulation plate frame


Outer mea-sure (cm)A x B

Weight be-fore filling (kg)

S/O*

BV-Thermo 55 50 x 50 63.5 x 63.5 19 kg O

BV-Thermo 66 60 x 60 73.5 x 73.5 23 kg O

BV-Thermo 86 80 x 60 93.5 x 93.5 29 kg O

BV-Thermo 88 80 x 80 93.5 x 93.5 33 kg O

BV-Thermo 106 100 x 60 113.5 x 73.5 33 kg O

BV-Thermo 110 100 x 100 113.5 x 113.5 45 kg O

BRE-*S = IN STOCK O= ORDER PRODUCT


BVA ALUMINIUM ROW ACCESS COVER

Load endurance: 125 kNMaterial:the frame and cover edges are made of extruded alu-minium, the base of aluminium plate.Properties: the two or three-part access cover with a seal is manu-factured with accurate dimensions. Thanks to its small corners and accurately dimensioned edge structure, the manhole is almost in-conspicuous in the flooring after its installation.Ideal for locations where extremely high requirements are set for the appearance of the access cover's visible edge.The reinforcement in the access cover improves structural load en-durance. The patented detachable intermediate spoke allows the access cover to be opened across its whole length.Properties: the access cover has two or more parts and a seal and is manufactured with accurate dimensions. Almost gas and water-proof (if subject to continuous water flow, some water may leak out from between the cover and the frame). The reinforce-ment in the access cover improves structural load endurance. Applications: challenging access covers in indoor use when high requirements are set for the appearance of the access cover's vis-ible cover edges, or when the floor must be ground afterwards (e.g. parquet floors).

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Base plate8. Corner welding9. Locking nut10. Divider11. Dividerseal12. Dividerlocating sleeve

The cross-sectional drawing of the BVA row access cover.




S/O*

BVA multi 2-part 60 x 132 72 x 144 23 kg O





BRE-*S = IN STOCK O= ORDER PRODUCT


BV-RA MULTI STEEL ACCESS COVERBVE-RA MULTI STAINLESS STEEL ROW ACCESS COVER

Load endurance:125 kNMaterial: The frame and cover of the BV-RV access cover is made of a 2 mm steel profile. The structure is galvanised after welding. The frame of the BVE-RA manhole is made of 2 mm stainless steel (quality 304). The surface is passivated throughout after welding. access covers made of acid-proof stainless steel (quality 316) are also available.

Properties: theaccess cover has two or more parts and a seal and is manufactured with accurate dimensions. Almost gas and water-proof (if subject to continuous water flow, some water may leak out from between the cover and the frame). The reinforcement in the access cover improves structural load endurance.

The patented intermediate spoke detachable without tools allows the access cover to be opened across its whole length. The height of the access cover chute is about 50 mm. The access covercan be equipped with a higher 100 mm chute on order. The chute is filled up with yard paving stones.Applications: challenging objects, such as those in industrial premises and airports. Dimensions: steel and stainless steel row access cover are made to order in accordance with accurate dimensions. We have made row access covers, for instance, for sewers with several tens of ac-cess covers in parallel.


Load endurance: 125 kNMaterial: the frame and cover edges are made of extruded aluminium, the base of aluminium plate.Properties: gas and water-proof row access cover which is manufactured with accurate dimensions. Thanks to its small corners and accurately dimen-sioned edge structure, the manhole is almost in-conspicuous in the flooring after its installation. Ideal for locations where extremely high require-ments are set for the appearance of the access cover's visible edge. The reinforcement in the access cover improves structural load endurance. The patented detachable intermediate spoke al-lows the access cover to be opened across its whole length. The delivery of more than 3-me-tre long row access cover includes separate side frames that are easy to lengthen.Almost gas and water-proof (if subject to continu-ous water flow, some water may leak out from between the cover and the frame). The reinforce-ment in the access cover improves structural load endurance. Applications: challenging access cover in indoor use when high requirements are set for the ap-pearance of the access cover's visible cover edges, or when the floor must be ground afterwards (e.g. parquet floors). Ideal for cable and HEPAC ducts that must be opened across their whole length.

BVA-RA ALUMINIUM ROW ACCESS COVER

The light, hinged access cover is easy to open.

1. Frame2. Cover3. Seal4. Reinforcement5. Locking bolt6. Shield plug7. Base plate8. Corner welding9. Locking nut10. Divider11. Divider seal12. Divider locating sleeve

Row access cover installed in the cor-ridor of a museum.

The cross-sectional drawing of the BVA row access cover.

HANDRAILS AND IMPACT GUARDSThe DionePro vinyl handrails and impact guards are easy-to-clean and protected against bacteria. The vinyl-coated protective products are durable in premises subject to heavy use, such as hospi-tals and health centres. They are also commonly used in assisted living facilities, offices and ships. The vinyl products designed to protect real estates are shock-proof and help keep inner surfaces of the real estates in good condition for a long time.

The colour of the vinyl protection profiles can be chosen from among 60 different colour options! The selection includes different handrail options, impact guide options mounted horizontally on the wall and outer corner protection profiles mounted on the walls. All products are available in tones that fit in with each other. The delivery includes all mounting accessories as well as end and connection pieces.

HANDRAILS AND IMPACT GUARDSGood and safe hygienic solutions that last for a long time in health care premises.

60 www.dionepro.fiIMPACT GUARDS, HANDRAILS AND SUPPORT

BR-400V

VINYL-COATED HANDRAILS WITH ALUMINIUM FRAMEThe easily cleaned and durable handrail solutions are well suited to hospi-tals, nursing homes and other public premises.

All vinyl-coated handrails and impact guards are made on order and in tones that fit in with each other.

Material: made of vinyl-coated aluminium. Standard measure3.66 m. The selection includes 60 colour options.Fastening:easy and quick to mount. The delivery includes mounting acces-sories.End and corner pieces are available.Applications: a durable handrail solution for many premises, such as of-fices, hotels, schools, shopping centres, hospitals and other public premises.

BR-400V1. 1 1/2” diameter2. Vinyl handrail3. Decoration strip4. Mounting screws5. Vinyl impact guard6. Impact absorber7. Aluminium frame8. Wall bracket9. Wall reinforcement

BR-400V1. BRL-425V end piece2. 3 1/8” diameter3. Mitre joint in the inner corner4. BRA-400V aluminium frame5. OBR-450V outer corner6. Factory-made joint extension7. BR-108 clip8. BRV-1200 vinyl-coated surface section9. BRR-425V end piece10. B-100 impact ab-sorber11. BRI-400V decoration12. WGV-4 vinyl-coated surface section

Assembly drawing (all necessary parts included)


S/O*

BR400V handrail/impact guard 365 cm BR400V O

BR400V corner piece OBR-450V O

BR400V bracket BR-108 O

BR400V end piece (left) BRL425V O

BR400V end piece (right) BRR425V O

*S = IN STOCK O= ORDER PRODUCT, DELIVERY TIME 3 MONTHS

www.dionepro.fi 61IMPACT GUARDS, HANDRAILS AND SUPPORT

BR-500V

BR-1200

Width/type Length Product code S/O*

BR500V handrail/impact guard

365 cm BR-500V O

BR500V corner piece IOC-527 O

BR500V bracket BR-107 O

BR500V end piece BR-527 O


BR-500V1. 1 1/2” diameter2. Vinyl-coated surface section3. Mounting screws4. Aluminium frame5. Wall bracket6. Wall reinforcement

BR-500V1. 2 15/16”2. BR-527 end piece3. IOC-557 inner/outer corner4. IOC-557 inner/outer corner5. BRV-500 vinyl-coated surface section6. Factory-made joint extension7. BRA-500 aluminium frame8. BR-107 clip9. BR-527 end piece



BR1200 handrail/impact guard 365 cm BR-1200 O

BR1200 corner piece IOC-1250 O

BR1200 bracket BR-1206 O

BR1200 end piece (right) BRR-1225 O

BR1200 end piece (left) BRL-1225 O


BR-12001. BRL-1225 end piece2. BRV-1200 vinyl-coated surface section3. IOC-1250 inner/outer corner4. IOC-1250 inner/outer corner

BR-12001. Aluminium frame2. 1 1/2” diameter3. Vinyl-coated surface section4. Wall bracket5. Mounting screws6. Wall reinforcement


5. BR-1206 clip6. Factory-made joint extension7. BRA-1200 aluminium frame8. BRR-1225 end piece9. 3”



WG-6C impact guard 365 cm WG-6C O

WG-6C end piece ETC-6C O

WG-6C corner piece (outer) OTC-6C O

WG-6C bracket clip WG-6C-ASM-1 O



WG-8C Corner piece (outer) OTC-8C O

WG-8C bracket clip



WG-5C corner piece (outer) OTC-5C O

WG-5C corner piece (inner) ITC-5C O

WG-5C bracket clip WG-8C-ASM-1 O


WG-7C end piece ETC-7C

WG-7C corner piece (outer) OTC-7C

WG-7C corner piece (inner) ITC-7C

WG-7C bracket clip WG-7C-ASM-1


CLIP-FASTENED VINYL IMPACT GUARDS

Material: easy-to-clean vinyl coating. Mounting clips are provided with im-pact-absorbing springs.Fastening: easy and quick to mount. End pieces are available.Applications: offices, hotels, schools, shopping centres, hospitals and other public premises.

The surface of clip-fastened vinyl-coated impact guards is easy to keep clean.The clip-fastened guards are equipped with impact-absorbing springs. The delivery includes end pieces if required.

WG-5C, WG-6C, WG-7C, WG-8C1. Mounting screws2. Vinyl-coated surface section3. Mounting clip4. Brackets for end pieces

WG-5C cross-sectional drawing WG-6C cross-sectional drawing WG-7C cross-sectional drawing WG-8C cross-sectional drawing


CG-20R CG-10R

PLASTIC-FRAMEDVINYL-COATED CORNER PROTECTION PROFILE

Material: easy-to-clean vinyl coating. The mounting rail is made of flexible recycled plastic.Fastening:easy and quick to mount. End pieces are available.Applications: offices, hotels, schools, shopping centres, hospitals and outer corners in other public premises.

The shock-resistant vinyl-coated corner protection profile protects efficiently against dents. Available in tones that fit in with the rest of the interior decoration.The delivery includes end pieces.


51 x 51 mm, corner protec-tion profile

244 cm CG-20R O

76 x 76 mm, corner protec-tion profile

244 cm CG-10R O




(10)White

(301)LinenWhite

(554)Mission White

(541)White Sand

(361)Pearl

(370)Eggshell

(313)Champagne

(648)Monterey

(411)Prumice

(555)Porcelain

(193)Wheat

(2)Ivory

(263)Pale Yellow

(569)Saffron

(497)Chablis

(676)Dover White

(268)Doeskin

(379)Mojave Sand

(148)Desert Sand

(3)Tan

(682)Khaki Brown

(718)Silkworm

(21)Cappuccino

(113)Toffee

(204)Shell

(486)Caisson

(359)Ginger Spice

(288)Mocha

(694Café Au Lait

(4)Brown

(385)Beige Desert

(22)Woodlands

(176)Taupe

(238)Bone

(483)Harvard Gray

(297)Chinchilla

(210)Silver Gray

(289)Pearl Gray

(5)Gray

(1)Black

(293)See Foam

(369)Blue Fog

(29)Blue Ice

(265)Windsor Blue

(490)Blue Bird

(520)Brittany Blue

(583)Alexis Blue

(377)Teal

(382)Stormy Blue

(371)Sage Green

(376)Pale Jade

(300)Grotto

(156)Hunter Green

(269)Ecru

(494)Lavender Hetather

(366)Soft Peach

(381)Dawn

(373)English Rose

(304)Victorian Rose

(380)Cordovan

COLOUR MAPOur colour map for vinyl materials enables you to emphasise or fade out elements and shapes with soft protection profiles and handrails.

The tones in the colour map are suggestive. Please check the tones from the material map in connection with ordering.


EB -10

EB-1

SHOPPING TROLLEY SHELTERSTrolley shelters are ideal for protecting walls in shops and hospitals, for example.

• Aluminium frame

• Durable and flexible vinyl coating

• End pieces for the profile are available.

• A total of 60 colour options available!

NEW PRODUCT

Flexible vinyl-coated profile

Mitre joint of inner corners

Mounting screws - fastened to the wall at intervals of 45 cm

Steel rail

EB-5 end piece

Outer corners Steel rail

EBV-10 flexible vinyl-coated profile

EB-5 end piece


Mounting screws - fastened to the wall at intervals of 80 cm

Aluminium mounting rail

Mitre joint of inner corners

Outer corner


Aluminium rail

EBP-2 end piece

Factory-madejoint


CORNER PROTECTION PROFILES FOR PARKING HALLS

CG-2E HEAVY-DUTY CORNER PROTECTION PROFILE, BLACK

Rubber corner protection profiles are well suited to extremely hard indoor and outdoor use.

NEW PRODUCT

14 mm

Minimum corner radius

Fastened with screws at intervals of 90 cm

Equipped with holes at the instal-lation stage

Corner protec-tion profile

22 mm radius

CG-15 HEAVY-DUTY CORNER PROTECTION PROFILE, BLACK OR YELLOW

CG-4 CORNER PROTECTION PROFILE, BLACK

End piece

End piece

Skirting profile

Corner protec-tion profile

Delivered without holes (glue-fastened)

Steel mount-ing rail

EDPM rubber profile

Mounting screws

Specified height

Specified height

32 mm radius


WT-25

MD-5

E-1 M-2

D-3

NEW PRODUCTIMPACT GUARDS FOR PARKING HALLSApplications:

• parking halls

• industrial premises

• loading platforms

IMPACT GUARDS FOR MARINE TRAFFIC

Weather-proof impact guard is ideal for extremely hard outdoor use.

Applications:

• quays

• ships


Model Material Colour Dimensions (mm)

Diameter (mm) Consignment (pcs)

S/O Illustration

108-45S108-60S108-70S108-80S108-90S

Stainless steelStainless steelStainless steelStainless steelStainless steel

satinsatinsatinsatinsatin

450 x 85 mm 600 x 100 mm700 x 100 mm 800 x 100 mm900 x 100 mm

32 mm32 mm32 mm32 mm32 mm

10 pcs10 pcs10 pcs10 pcs10 pcs

TTTTT

104-91S104-106S104-120S104-182S104-274S


satinsatinsatinsatinsatin

915 x 85 mm1067 x 85 mm1200 x 85 mm1828 x 85 mm2743 x 85 mm



TTTTT

109-45S Stainless steel satin 450 x 200 mm 32 mm 5 pcs T


413-60S413-70S413-85S413-90S

Stainless steelStainless steelStainless steelStainless steel

satinsatinsatinsatin

600 mm700 mm850 mm900 mm

32 mm32 mm32 mm32 mm

5 pcs5 pcs5 pcs5 pcs

TTTT



DionePro support handrails are shock and corrosion-resistant, high-quality safety products. They provide elderly, physically disabled people with means of coping independently with the challenges set by their living environment at home.

The handrails and handles are made of stainless steel and pro-vided with satin coating or white-powder painting. The prod-ucts are easy to mount and durable during the whole building's life cycle in assisted living facilities and hospitals.

SUPPORT HANDLES AND HAND-RAILS FOR ASSISTED LIVING FACILI-TIES AND SENIOR CITIZENS' HOMES

NEW PRODUCT


Model Material Colour Dimensions (mm)

Diameter (mm) Consignment (pcs)

S/O Illustration

108-45W108-60W108-70W108-80W108-90W


white powder paintwhite powder paintwhite powder paintwhite powder paintwhite powder paint

450 x 85 mm 600 x 100 mm700 x 100 mm 800 x 100 mm900 x 100 mm



TTTTT

104-91W104-106W104-120W104-182W104-274W


white powder paintwhite powder paintwhite powder paintwhite powder paintwhite powder paint

915 x 85 mm1067 x 85 mm1200 x 85 mm1828 x 85 mm2743 x 85 mm



TTTTT

109-45W Stainless steel white powder paint 450 x 200 mm 32 mm 5 pcs T


413-60W413-70W413-85W413-90W

Stainless steelStainless steelStainless steelStainless steel

white powder paintwhite powder paintwhite powder paintwhite powder paint

600 mm700 mm850 mm900 mm

32 mm32 mm32 mm32 mm

5 pcs5 pcs5 pcs5 pcs

TTTT



Duuri Oy works in cooperation with architects and industrial designers to design accessories for elderly people. Such a product set is right now under development that improves the comfort of assisted living facilities and homes for senior citizens while providing physically disabled people with full support and increased safety in their living environment.


FREQUENTLY ASKED QUESTIONSPROFILES How to cut stainless steel profiles?

The easiest way is to use a wheel fit for cutting stain-less steel. The wheel is attached to an angle grinder. The profiles are cut to mitre by using a suitable cut-off saw/metal blade combination, or a bandsaw fit for cutting stainless steel. Individual profiles are easy to cut and saw to mitre with a hacksaw as well.

Are DuuriPro products fit for premises with a swim-ming pool?If in contact with chlorinated water, the profiles or manholes must be made to order from acid-proof steel. Tiling profiles can also be made of plastic. The delivery time for made-to-order, acid-proof steel manholes is 3–4 weeks and the delivery time of skirt-ings is 2–3 weeks.

How to lengthen vinyl handrails in long corridors?The delivery includes an appropriate number of extension pieces to make it possible to connect the extension points with each other. It is advisable to prepare extension points from factory-made ends to ensure that the joint is inconspicuous.

Why is there a dent outwards from the inside in one of the access cover edges?Has the access cover been damaged during trans-port?The dent is a locating mark. It ensures that the man-hole is easy to close after opening. Closing the man-hole in the same position after it has been opened makes it possible to put it easily in place, in spite of the stress that might have occurred in the manhole at the calvanising or casting stage. The dent is not transport damage but a specifically designed detail to prove that the quality of the design and finish is excellent.

What is the easiest way to clean vinyl-coated hand-rails and impact guards?The vinyl surface can be cleaned with standard de-tergents during general cleaning.Is it possible to change the vinyl surface strip when necessary without replacing the whole profile?The surface strip in DionePro vinyl profiles can be replaced during renovation and when the decora-tion tones are changed. As it is mounted directly on top of the old aluminium strip, it is not necessary to replace the whole profile, which saves costs and natural resources.

www.dionepro.fiwww.dione.fi

INSPECTION AND ACCESS HATCHES

HANDRAILS

How to ensure waterproofness when mounting a hatch/access cover in place?The stainless steel and steel manholes with seals are water-proof. The base plate of aluminium man-holes is welded with spot welding (e.g. BVA). If the manufacturing method requires an absolutely water-proof solution, the manhole must be cast with water-proof concrete, or the bottom side of the flooring provided with water-proof insulation. The connection point between the floor and the manhole frame must be made water-tight by using a suitable additive in the concrete when manhole edges are attached to the floor by casting.If in doubt, please consult our sales department for additional information.

Is it possible to mount the access cover directly on the floor at the surface casting stage?Pay special attention to potential shrinkage and expansion at the casting's drying stage. The man-hole cover must be in place in the frame during in-stallation. Use flexible wedges (minimum width 10 mm) in the outer edges of the frame, if necessary. Remove the wedges when the surface casting has dried. Seal the grooves after this with a flexible seal-ing compound.

FREQUENTLY ASKED QUESTIONS

Duuri Oy’s sales and delivery terms

1. Scope of application

These Duuri Oy’s sales and delivery terms shall, unless otherwise agreed, be applied in transactions concerning trade in goods (hereinafter “products”) between Duuri Oy and its customer (hereinafter also the Buyer), where Duuri Oy is the seller of the goods. The Buyer and Duuri Oy are referred to jointly as the Contracting Parties.

When placing an order, the Buyer accepts these sales and delivery terms.

2. Offer

2.1

Duuri Oy may give a written offer concerning the products to the Buyer. The offer shall be valid for 30 days from the date of the offer, unless otherwise stated in the offer.

2.2

A contract comes into being when the Buyer accepts the offer during the period of validity of Duuri Oy’s offer.

2.3

An acceptance that arrives after the period of validity has lapsed or a reply that includes additions, limitations or conditions is considered to be a counter-offer by the Buyer. A contract comes into being on the basis of a counter-offer if Duuri Oy states that it accepts the counter-offer.

3. Order and confirmation of order

3.1

The Buyer may place an order for products, even in the absence of an offer, either orally (e.g. by telephone) or in writing (including telefax and email). In the order, the Buyer shall specify the person placing the order, the goods ordered, the delivery address, required time of delivery and contact person.

3.2

If Duuri Oy accepts the order as such, Duuri Oy shall give the Buyer a written confirmation of order (including telefax and email) in which it confirms the order. If Duuri Oy does not accept the order as such, they shall inform the Buyer of this.

3.3

If Duuri Oy has not given a written confirmation of order, but delivers the ordered goods in accordance with the order, this is held to be a confirmation of order by the same.

4. Ranking order of validity of contract documents

Contract documents supplement each other. If contract documents are mutually contradictory, they shall be observed in the following order of validity, unless otherwise mentioned in the contract:

- a written contract including its appendices

- confirmation of an order including its appendices

- a written order including its appendices

- an offer including its appendices

- Duuri Oy’s sales and delivery terms

- an invitation for tenders

5. Pricing and invoicing

5.1

The prices in Duuri Oy’s price list do not include value added tax. Prices in offers do not include value added tax, unless otherwise stated. Value added tax and any other such taxes or fees shall be added to the stated prices and shall be invoiced in accordance with legisla-tion in force at the time. Prices and other information in price lists are for reference and Duuri Oy reserves the right to make changes.

5.2

Products shall be invoiced at the price valid on the date of delivery, unless otherwise agreed.

5.3

The prices only include Duuri Oy’s standard packaging.Any other packing materials shall be charged for separately. A charge of 10 € / each shall be made for customer pallets.

5.4

Duuri Oy reserves the right to make price adjustments if exchange rates, raw material prices, import charges or other fees, taxes or public fees change after making the offer and before payment by the Buyer. With regard to exchange rates, Duuri Oy is entitled to adjust the price if the exchange rate difference between the date of offer and the date of payment is greater than 2%. Duuri Oy observes the average rate of exchange quoted by the European Central Bank.

6. Transfer of ownership

The ownership of a product is transferred to the Buyer when the whole purchase price is paid. However, the Buyer is entitled, in the course of his normal business activity, to sell also such products that have not yet been paid and for which payment is not yet due. Ownership is then transferred to the Buyer’s customer when the product is delivered.

7. Payment of the purchase price

7.1

The purchase price is paid against the invoice in accordance with agreed payment terms. The term of payment is fourteen (14) days net. The purchase price is deemed to have been paid when the payment arrives in Duuri Oy’s account.

7.2

If the Buyer does not pay the purchase price within the agreed time, Duuri Oy is entitled to charge interest on arrears as mentioned in the contract or invoice and may charge reasonable collection charges. Duuri Oy shall charge 16% interest on arrears from the due date onwards. Duuri Oy shall charge an additional invoicing charge of 10 € for sending an invoice for interest on arrears.

7.3

If the Buyer has any receivables from Duuri Oy, the set-off of the receivable against any invoice must be agreed separately with Duuri Oy.

7.4

If the Buyer delays considerably in making payment, Duuri Oy is entitled to cancel the transaction. The Buyer is then obligated to reimburse Duuri Oy in full for the costs incurred in cancelling the transaction and getting the goods back, including any collection charges.

8. The delivery condition of the product

8.1

Duuri Oy shall be responsible for the quality and other characteristics of the products as defined in the agreement so that they are in accordance with information given in writing by Duuri Oy specifically for the transaction in question.

8. 2

The Buyer shall be responsible for the correctness of the detailed information given to Duuri Oy concerning the purpose of use and the measurements of the products ordered.

8.3

The Buyer shall give notice of any delays in delivery or defects in the products within eight (8) days from the date of delivery in order to retain its right to make a claim concerning the defect. If the defect is noticed la-ter, and it was not possible to notice it earlier, the Buyer must give notice of the defect immediately in order to retain its right to make a claim concerning the defect.

9. Terms of delivery

9.1

The delivery place of the products shall be Duuri Oy’s warehouse in Helsinki (Ex Works, Incoterms 2000).

When agreed, Duuri Oy shall deliver the products to the Buyer at the Buyer’s expense (FCA, Incoterms 2000).

Deliveries in Finland that exceed seven hundred (700) euros in net value excluding value added tax may be delivered freight paid if so agreed (CPT, Incoterms 2000).

9.2

The recipient of the product shall inspect the packages and acknowledge receiving the products in accordance with the delivery note by signing it. Any notices concerning the quantity and condition of the products shall in this connection be recorded in the delivery note which shall also be signed by the carrier. Furthermore, any notices concerning the quantity of products delivered shall be given to Duuri Oy within two (2) working days of receiving the products.

9.3

The instructions given by Duuri Oy concerning transporting and storing shall be observed.

10. Time of delivery and delays

10.1

The normal time of delivery for standard goods in stock is five (5) working days, unless otherwise agreed.

10.2

If the Contracting Parties have agreed on the time of delivery and Duuri Oy is late in delivery, Duuri Oy is obligated to inform the Buyer immediately when it gets to know of the delay. At the same time Duuri Oy shall report the reason for the delay and shall, if possible, give a new estimated time of delivery.

10.3

If a definite date of delivery has been agreed and the delay on the part of one Contracting Party causes essential damage to the other Contracting Party, this Party is entitled to cancel the agreement with regard to the delayed delivery lot after negotiating with the Party causing the delay.

11. Guarantee

11.1

The products may have a valid guarantee possibly granted by their manufacturer. This must always be ascertained for each product. The guarantee period starts from the date of delivery. Duuri Oy is not res-ponsible for guarantees given by other manufacturers, or how they are implemented.

11.2

A guarantee is valid only if the handling, use, mainte-nance and other corresponding instructions for the product have been observed properly. Furthermore, in order for the guarantee to be valid, it is necessary that the Buyer has fulfilled its obligations arising from the delivery and as defined in the contract.

11.3

If defects in raw materials or manufacturing are found in the product, this must be reported immediately to Duuri Oy during the guarantee period, however, not later than twelve (12) months from the date of delivery.

11.4

Duuri Oy pledges with regard to products that it guarantees, either to repair the defective product or replace it with a new product, at its own discretion and at its own cost. On the part of other products, Duuri Oy is entitled at its own discretion and at its own cost, either to repair the defective product or replace it with a new product. The guarantee on products that

have been repaired or replaced is valid up to the end of the guarantee period of the original product.

12. Returns

It is necessary that Duuri Oy gives its consent in ad-vance before any returns are made. No credit is given for goods returned without consent. Returns must be implemented within thirty (30) days of delivery of the products. Duuri Oy shall credit 80% of the invoiced price of faultless products that are returned in unopened packages at the Buyer’s cost. No credit is given for products that are tailor-made.

The following shall always be reported when returning:

- the number and date of the invoice and delivery note,

- with whom was the return agreed and when, and

- the reason for the return.

13. Limitation of liability

13.1

Duuri Oy is not liable for any damage caused by delayed delivery of products unless the Contracting Parties have specifically agreed on this.

13.2

Duuri Oy shall not be liable for any production losses or for any unrealised profits or for any other indirect damage caused by its products or its activity.

13.3

Duuri Oy shall not be liable for any direct damage to persons, things or property caused by the products unless it can be proved that the damage was caused by a faulty product. In that case the upper limit of Duuri Oy’s liability for damages is the price of the product that caused the damage.

13.4

Duuri Oy shall not be liable for any damage that is caused when products are used for any purposes other than those for which they are specifically intended.

13.5

These terms of limited liability do not, however, limit the liability of Duuri Oy under mandatory legislation for damage caused by the products.

14. Force Majeure

A basis for release (force majeure) from the obliga-tions under the contract is deemed to be such an abnormal event that affects the case and prevents the fulfilment of the contract after the contract has been made and which the Contracting Parties had no reason to take into consideration when the contract was made and which is beyond the control of the Contracting Parties and its inhibitory effects cannot be eliminated without unreasonable additional costs or unreasonable loss of time. Such an event may be war, internal unrest, requisition or confiscation by the authorities, import or export ban, natural catastrophe, stoppage of public transport or energy supply, labour dispute, fire or other equally significant and abnormal reason that is beyond the control of the Contracting Parties.

15. Governing law and dispute resolution

The agreement between Duuri Oy and the Buyer concerning orders and deliveries of products shall be governed by Finnish laws.

Differences of opinion between Duuri Oy and the Bu-yer concerning orders and deliveries of products shall be solved in the Helsinki District Court as the court of first instance, if the Contracting Parties are unable to reach mutual understanding on their differences through negotiation.

Duuri Oy’s sales and delivery terms1.9.2011


ООО «Дюри Профайл Рус» г.Апрелевка, Сентябрьская ул., д.1255302,143362 МоскваРОССИЯТел: +7-495-982 3875 Факс+7-495-982 3875 [email protected]

Prin

ted

in 2

011

Duuri Oy

Tapulikaupungintie 35PL 26, 00750 HelsinkiFINLANDtel +358-9-351 050 fax +358-9-3510 [email protected]

D-Profile Ab

Kabelvägen 1055302 JönköpingSVERIGEtel +46 36 186 363fax +46 36 186 [email protected]

D-Profile As

Revefaret 123060 SvelvikNORGEtel +47 3377 3275fax +47 3377 [email protected]

SIA D-Profile

Rigas iela 62114 OlaineLATVIAtel +371 778 3506fax +371 778 [email protected]

www.dionepro.fi

Documents

Pro-kuvasto eng