Printer Driver Manual - files.oceusa.comfiles.oceusa.com/media/Assets/PDFs/TSS/external/ix3010/... · The Imagistics Printer driver CD contains the printer driver and TWAIN driver

Printer ControllerTWAIN Driver

User's Guidefor use with ix3010

Software License AgreementREAD BEFORE INSTALLATION

This Software License Agreement (hereinafter the “Agreement”) is a legalcontract made between you (regardless of an individual or a legal entity)and our company, (“Imagistics International Inc.”) regarding softwareproducts contained in this CD-ROM (hereinafter the “Software”). Pleaseread the following terms carefully before installing the Software. You caninstall and use the Software subject to your acknowledge and acceptanceof all of the following terms. If you do not agree to any of the followingterms, you should cancel the installing process.

The condition of the software license:

1. Any and all copyright and any other intellectual property regarding theSoftware remain solely the property of Destiny Technology Corporation (here-inafter “Destiny”).

2. You may use the Software only in the country of your purchase and only for usewith our companies’ hardware.

3. You must not modify, alter all or any part of the Software. You must not makeany attempt to discover the source code of the Software by any method includ-ing reverse-engineering, de-compiling, or de-assembling.

4. You must not sell, transfer, rent, lease or sublicense the Software to any thirdparty by transmitting the software via phone-line or network, or by copying thesoftware to floppy disk, CD-ROM, magnetic data tape or any other media.

5. The software is subject to changes by Destiny in its specifications and programwithout any prior notice.

6. Before installing the software, you are supposed to take any and all proceduresnecessary to secure your records and data at your cost and responsibility,including making backup of your computer files. Neither our company, our dis-tributors/sub-distributors, nor Destiny shall be liable for any damage or losscaused by your failure of taking the foregoing procedure.

7. Neither our company, our distributors/sub-distributors, nor Destiny shall beliable for any damage or loss caused by (1) use of the software in combinationwith the hardware other than the hardware which is defined in Section 2 aboveor (2) modification of the software.

8. Neither our company, our distributors/sub-distributors, nor Destiny shallassume any damages incurred by you or a third party even if such damage isdirectly/indirectly caused by use of the software or incapability to use the software.

The Imagistics Printer driver CD contains the printer driver and TWAINdriver. The printer driver allows you to use your machine as a PC printer,and the TWAIN driver allows you to use your machine as a scanner.

About this manualThis manual contains the information you need to install and use theImagistics printer driver and Imagistics TWAIN driver with your ix3010.Chapter 1 describes installing the Imagistics printer driver and usingthe Imagistics printer driver.Chapter 2 describes installing the Imagistics TWAIN driver and how touse it with your ix3010.

Get the latest printer driverTo obtain the latest version of the printer driver, please contactImagistics.

If problems ariseIn the event your machine requires service or repairs, please contactImagistics.For information, contact the Imagistics Diagnostics Center at 800-243-5556 (from U.S. only).

i

Introductions

Trademark and Copyrights• Imagistics, the Imagistics logo and all Imagistics product names contained herein

are trademarks of Imagistics International, Inc.

• Destiny® is a registered trademark of the Destiny Technology Corporation.• LaserAct® is a registered trademark of the Destiny Technology Corporation.• DPOS® is a registered trademark of the Destiny Technology Corporation.• WinPanel® is a registered trademark of the Destiny Technology Corporation.• LaserAct® Copyrights © 1992-1999, Destiny Technology Corporation, Ver.2.0

All Right Reserved.

• WinRefs® Copyrights © 1995-1999, Destiny Technology Corporation, Ver.2.0All Right Reserved.

• WinPanel® Copyrights © 1995-1999, Destiny Technology Corporation, Ver.1.0All Right Reserved.

• i486, i486DX and Pentium are either registered trademarks or trademarks ofthe Intel Corporation.

covered by one or more of the following US Patents:5,029,108:5,396,584; and bypatents in other countries.

• Agfa and Agfa Rhombus are registered trademarks of Agfa-Gevaert N.V.

• Universal Font Scaling Technology (UFST) is a trademark of AgfaCorporation.

• PCL is a registered trademark of the Hewlett Packard Company.

• Centronics® is a registered trademark of the GENICOM Corporation.

• Microsoft®, Windows®, Windows® 3.1, Windows® 95, Windows® 98, Windows®

Me, Windows NT® 4.0, Windows® 2000 and Windows® XP are registered trade-marks of the Microsoft Corporation.Screen shots reprinted by permission from the Microsoft Corporation.

• Adobe®, Adobe Acrobat®, Adobe Acrobat Reader® are registered trademarks ofAdobe Systems Incorporated.

All other products referenced are trademarks or registered trademarks of theirrespective companies.

ii

Navigating PDF documents

Paging through PDF documentsTo go to the first page, click this button.To go to the previous page, click this button.To go to the next page, click this button.To go to the last page, click this button.To go to back for each step back, click this button.To go to forward for each step forward, click this button.

Adjusting the view of a PDF documentTo return a page to its actual size, click the Actual Size button.To resize the page to fit entirely in the window, click the Fit InWindow buttonTo resize the page to fit the width of the window, click the Fit WidthbuttonIf you need to magnify a page to a size larger than the window, usethe hand tool ( ) to move the page around so that you can view allthe areas on it.To magnify and reduce the view, select the zoom tool, and click thepage. When the zoom-in tool is selected, you can press Ctrl whileclicking to zoom out instead of in. When the zoom-out tool is selected,press Ctrl to zoom in.

iii

Browsing the PDF document

To browse using a bookmark:1 To display the bookmark palette, click Bookmarks tab or icon.2 To jump to a topic using a bookmark, click the bookmark’s icon or text

in the palette.

To follow a link:1 Select the Hand tool ( ) or zoom tool.2 Position the pointer over the linked area on the page until the pointer

changes to a hand with a pointing finger ( ). Then click the link.To go to back for each step back, click button.To go to forward for each step forward, click button.

iv

Introductions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iAbout this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iGet the latest printer driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iIf problems arise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iTrademark and Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iiNavigating PDF documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Chapter 1Using your machine as a printer

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1

Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2Doc Pilot and Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2Connecting the ix3010 to your computer . . . . . . . . . . . . . . . . . . . .1.2Installing Doc Pilot and Remote Shuttle . . . . . . . . . . . . . . . . . . . .1.3

Installing using Setup.exe . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.3Print Test Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.8Plug and Play Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9Installing the printer driver from Add Printer Wizard . . . . . .1.12

Printer driver settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.15Open the printer properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.15

From the application software . . . . . . . . . . . . . . . . . . . . . . . . .1.15From the printer icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.17

Printer settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.19Paper tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.21Page Layout tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.27Quality tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.29Device Option tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.31

Using the Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.32About Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.32Installing the Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . .1.32Start the Remote Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.32Remote Shuttle screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.33Remote Shuttle icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.33Printer setting from Remote Shuttle . . . . . . . . . . . . . . . . . . . . . .1.34

The priority of the setting is as follows: . . . . . . . . . . . . . . . . . .1.34Open the Printer setting screen . . . . . . . . . . . . . . . . . . . . . . . .1.34Paper tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.35Printer setting tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.36

v

Table of contents

PCL font tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.37Test print tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.38Net setting tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.39Configuration tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.40

Canceling the printing job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.41ONLINE key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.41To cancel a print job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.41

Using your machine on a Network . . . . . . . . . . . . . . . . . . . . . . . . . .1.42Connection through print server PC . . . . . . . . . . . . . . . . . . . . . .1.42Connecting through optional network interface . . . . . . . . . . . . .1.43

Peer to Peer network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.43Client/Server network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.43EtherNet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.44Entering the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.44Installing the software for your network environment . . . . . .1.46To remove the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.47

Set TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.48Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.49

Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.55Uninstalling the Doc Pilot and Remote Shuttle . . . . . . . . . . . .1.55

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.56Print the Demo Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.56Print the Printer Configuration Page . . . . . . . . . . . . . . . . . . . . .1.56Print PCL Font List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.56Print NIC status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.57AGFA Font Manager 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.57

Chapter 2 Using your machine as a scanner

System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2To install the TWAIN driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2To uninstall the TWAIN driver . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2

Getting ready to use the Imagistics TWAIN driver . . . . . . . . . . . . . . .2.3Important information regarding the Imagistics TWAIN driver 2.3

Scanning the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5Access to the Imagistics TWAIN driver . . . . . . . . . . . . . . . . . . . . .2.5Using the RS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6

Scanning with the RS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6Using the SB mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.8

The basic operation for the SB mode . . . . . . . . . . . . . . . . . . . . .2.8vi

Create or modify a scan box . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.9Scanning the image into a scan box . . . . . . . . . . . . . . . . . . . . .2.11Erasing a document stored in a scan box . . . . . . . . . . . . . . . . .2.13Erasing an empty scan box . . . . . . . . . . . . . . . . . . . . . . . . . . .2.15Printing a list of documents stored in the scan boxes . . . . . . .2.16Retrieving an image from the scan box . . . . . . . . . . . . . . . . . .2.17

Changing the initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.20Scan parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.20Scanner auto reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.22Printing a list of scanner settings . . . . . . . . . . . . . . . . . . . . . .2.22

Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.23

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.25Entering characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.25The list of scanner settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.27

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.28

vii

Chapter 1

Using your machine as aprinter

System Requirements

1.1

The following are the minimum system requirements to install and oper-ate the Doc Pilot and Remote Shuttle.

CPU: i486DX/66MHz or higherOperating System: Windows® 95

Windows® 98Windows® Millennium EditionWindowsNT® 4.0Windows® 2000Windows® XP

Hard Disk Drive: At least 10MB of available disk space for installingRAM: At least 8 MBTerminal Connector Interface: A bidirectional parallel interface

IEEE1284 (Compatible mode / Nibblemode / ECP mode)

You will also need a bi-directional parallel interface cable (printer cable)to connect your ix3010 to your computer.

Note:Actual requirements will vary based on your system configuration,applications and document that you will print.

Doc Pilot and Remote Shuttle

Doc Pilot (printer driver)The Doc Pilot is a PCL printer driver that enables your software applica-tions to access the ix3010’s printer features.The Imagistics PCL 6 driver option includes the following printer drivers:• Use the PCL 6 driver to take full advantage of the printer features.

The PCL 6 driver is recommended unless backward compatibility withprevious PCL drivers or older printers is necessary.

• Use the PCL 5e driver if you want to preserve compatibility with oldersoftware applications.

Remote Shuttle (printer monitor)The Imagistics PCL printer driver CD also includes a Remote Shuttle forDoc Pilot printer software for end-users.Remote Shuttle displays the status of your printer and can show and setthe default value of the printer parameters. This allows you to check theprinter status and set printer parameters from your PC easily and effi-ciently.Note:If you want to install the Remote Shuttle, please install it using the

setup.exe in the CD-ROM.

Connecting the ix3010 to your computer

1 Turn off both the ix3010 and your computer.

2 Connect the ix3010 to your computer using the bi-directional paral-lel interface cable. On the printer cable, please attach the ferritecore which is in the packing contents.

3 Turn on the ix3010, and then your computer.

Note: If the “Add New Hardware Wizard” or “Found New HardwareWizard” appears when you start Windows, please install theImagistics printer driver referring to “Plug and Playinstalling,” beginning page 1.9.

1.2

Installing

Installing Doc Pilot and Remote Shuttle

Note:To install the printer driver software using Windows NT®,Windows® 2000 or Windows® XP, you must be logged in as theadministrator.

Note:Before you install the software, please read the Readme.txt file inthe appropriate directory of the CD-ROM for important installa-tion information and helpful tips:<Drive>:\Printer\ix3010\<Windows version>\Setup\Readme.txt<Drive> is the drive letter for your CD-ROM drive.In <Windows version>, the following folder name will be applied toyour Windows version:

• Win3x : for Windows 3.1• Win9x_Me : for Windows 95/98/Me• WinNT4 : for Windows NT® 4.0• Win2000 : for Windows® 2000• WinXP : for Windows® XP

Installing using Setup.exe

You can install the Doc Pilot and Remote Shuttle using the following pro-cedure. The following example utilizes Windows XP.According to your Windows version, the procedure may vary. Inthis case, follow the instructions on the screen to install it.

1 Start Windows.

2 Insert the Imagistics PCL printer driver CD into your CD-ROMdrive.

3 Click Start, then select Run.

1.3

4 Type <Drive>:\Printer\ix3010\<Windows version>\Setup\Setup.exe and click OK.

<Drive> is the drive letterfor your CD-ROM drive.

In <Windows version>, thefollowing folder name willapply according to yourWindows version:

· Win3x : for Windows 3.1· Win9x_Me : for Windows 95/98/Me· WinNT4 : for Windows NT® 4.0· Win2000 : for Windows® 2000· WinXP : for Windows® XP

5 The “Doc Pilot ix3010 setupscreen” will appear. ClickNext.

6 The “Software LicenseAgreement screen” willappear. Read the agreementcarefully and, if you agree,click Yes.

Note: To cancel the setup,click No.

1.4

7 The “Type of Connectionscreen” will appear. SelectLocal, and click Next.

Note: If the ix3010 is con-nected to another PCon the local area net-work, selectNetwork.

8 Select the printer port.

(Normally LPT1 is selected)Click Next.

9 The “Printer Name screen”will appear. Click Next.

10 Select the components youwant to install, then clickNext.

Note: The Remote Shuttlewill not work in a net-work environment. Itworks only with theprinter (ix3010)directly connected toyour PC.

1.5

The “Remote Shuttle ix3010” will not appear on this screenwhen you select Network for “Type of Connection” in step 7.

11 When you click the RemoteShuttle, the following screenwill appear.

If you want to start the Remote Shuttle automatically whenWindows is started, click Yes. Otherwise click No. If you select No,you can start the Remote Shuttle from Windows Start menu.

12 Confirm the installing com-ponents, then click Next.

13 The following display (seeright) may appear on yourscreen. However, since thereis no problem functionally,click Continue Anyway tocontinue installation.

14 When the “Setup Completescreen” will appear, clickFinish to complete theinstallation.

1.6

15 After installing, “Doc Pilot” will appear in Programs on theWindows Start menu.

If you’ve set the “Remote Shuttle” to start automatically in step 11,the Remote Shuttle screen will appear.

Important: If you are using Windows XP and your printer as a localprinter, “Found New Hardware Wizard” may appear whenstarting Windows XP even though you have installed theprinter driver. In this case, please install the printer driveras described on page 1.9.

1.7

Print Test PageWhen you have finished installing the Doc Pilot, print the test page toconfirm that the printer has been set up properly.

1 Click on the Windows Startbutton and choose Printersand Faxes.

2 Right-click the “Doc Pilotix3010” icon and selectProperties from the menu.

3 Select the General tab, andthen click the Print Test Pagebutton.

4 The Windows Test Page will beprinted.

Note:If the test page did not print, click No or Troubleshoot and thenfollow the Windows Print Troubleshooter for help.

Note:If an error message is shown on your ix3010’s display, see “ErrorMessages,” page 1.49.

1.8

Plug and Play Installing

Windows 95/98/Me/2000/XP will automatically detect and configure adevice and install the appropriate device drivers.Note:If the Windows Plug & Play feature does not work or the “Device

Driver Wizard” appears, click Cancel to close it. Please install theImagistics printer driver using the setup program (see page 1.3).

Note:To install the printer driver using Windows® 2000 or Windows® XP,you must be logged in as the administrator.

Here, we explain plug and play installing with Windows XP.According to your Windows version, the procedure may vary. Inthis case, follow the instructions on the screen to properly installit.

1 Make sure that the ix3010 and computer are connected properlywith the bi-directional parallel interface cable.

2 Make sure the ix3010 is turned on and your computer is turned off.

3 Turn on your computer and start Windows.

4 The “Found New HardwareWizard” will appear.

Select “Install from a listor specific location”.

Insert the Imagistics PCLprinter driver CD into yourCD-ROM drive.

Click Next.

5 Select “Don’t search. Iwill choose the drive toinstall”, and click Next.

1.9

6 The “Add Printer Wizardscreen” will appear. ClickHave Disk.

7 Type <Driver>:\Printer\ix3010\<Windows ver-sion>\PCL6, then click OK.

<Drive> is the drive letterfor your CD-ROM drive.

In <Windows version>, thefollowing folder name will apply according to your Windows ver-sion:

· Win3x : for Windows 3.1· Win9x_Me : for Windows 95/98/Me· WinNT4 : for Windows NT® 4.0· Win2000 : for Windows® 2000· WinXP : for Windows® XP

Note: You can also browse through the folders by clicking Browse.

Note: When installing the PCL5e driver, type PCL5e instead ofPCL6.

8 Confirm that the Doc Pilot ix3010 PCL6 is selectedand click Next.

1.10

Note: The following display(see right) mayappear on yourscreen.However, since thereis no problem func-tionally, clickContinue Anywayto continue the instal-lation.

9 When the following messageappear (see right), clickFinish to complete theinstallation.

Note:To confirm the printer driver has been set up properly, print theTest Page (see page 1.8).

Note:If the other printer driver has been installed, this printer is not setas default printer. Open “Printers and Faxes” window and setthis printer as default printer.

1.11

Installing the printer driver from Add Printer Wizard

This section explains how to install from the Add Printer Wizard.

Windows 95/98/Me

1 Click on Start > Settings, then click on Printers.

2 Double-click the Add Printer icon.

3 Follow the instructions that appear on the screen.

4 Specify the printer connection.

5 In Printer manufacturer list, click Have Disk.

6 Insert the Imagistics Printer driver CD into your CD-ROM drive.Browse to the printer driver location, then click OK.<Drive>:\Printer\ix3010\Win9x_Me\Pcl6

7 Confirm that the “Doc Pilot ix3010 PCL6” is selected on the printerlist, then click Next.

8 Select the printer port, then click Next.

9 Use “Doc Pilot ix3010 PCL6” as printer name, then click Next.

10 Determine whether print the a Test page or not, then click Finish.

11 After installation, the “Doc Pilot icon” will be added in the printerfolder.

Windows NT 4.0



3 Specify the printer management.


5 On the Printer manufacturer list, click Have Disk.

6 Insert the Imagistics Printer driver CD into your CD-ROM drive.Browse to the printer driver location, then click OK.<Drive>:\Printer\ix3010\WinNT4\Pcl6

7 Confirm that the “Doc Pilot ix3010 PCL6” is selected on the printerlist, then click Next.

8 Use “Doc Pilot ix3010 PCL6” as printer name, then click Next.

1.12

9 Indicate whether this printer will be shared with other networkusers, click Next.

10 Determine whether to print a Test page or not, then click Finish.

11 After installation, the “Doc Pilot icon” will be added in printerfolder.

Windows 2000




4 Specify the printer connection.


6 On the Printer manufacturer list, click Have Disk.

7 Insert the Imagistics Printer driver CD into your CD-ROM drive.Browse to the printer driver location, then click OK.<Drive>:\Printer\ix3010\Win2000\Pcl6

8 Confirm that the “Doc Pilot ix3010 PCL6” has been selected on theprinter list, then click Next.

9 Use “Doc Pilot ix3010 PCL6” as the printer name, then click Next.

10 Indicate whether you want this printer to be available to otherusers, then click Next.

11 “Completing Add Printer Wizard” screen will appear, click Finish.

12 When “Digital signature not found screen” appears, since there isno problem functionally, click Yes.

13 After installation, the Doc Pilot icon will be added in the Printerfolder.

1.13

Windows XP

1 Windows XP Professional: Click Start, then skip to step 3.Windows XP Home edition: Click Start, then click Control Panel.

2 Click Printers and Other Hardware.

3 Click Printers and Faxes.

4 Click Add Printer in the Printer Task.

5 The Add Printer Wizard will start. Click Next.

6 Select the option that describes the printer you want to use, clickNext.


8 In “Install Printer software”, click Have Disk.

9 Insert the Imagistics Printer driver CD into your CD-ROM drive.Browse to the printer driver location, then click OK.<Drive>:\Printer\ix3010\WinXP\Pcl6

10 Confirm that the “Doc Pilot ix3010 PCL6” has been selected on theprinter list, then click Next.

11 Use “Doc Pilot ix3010 PCL6” as the printer name, then click Next.

12 Indicate whether you want this printer to be available to otheruser, then click Next.

13 “Completing Add Printer Wizard” screen will appear, click Finish.

14 When “Hardware Installation screen” appears, since there is noproblem functionally, click Continue Anyway.

15 After installation, the Doc Pilot icon will be added in the Printerfolder.

1.14

Printer driver settings

Open the printer propertiesTo change the printer settings, open the printer properties.There are two ways to open the printer properties:• From the application software• From the printer icon

Note:Changing the printer properties from the printer icon will changethem for all documents you print on this printer. To change theprinter properties for one document, change them from the applica-tion software.

From the application softwareTo open the printer properties from application software depends on thetype of application software you use. Please see your application soft-ware’s manual for details.

The following example utilizes Microsoft Word 2000.

1 Select Print from the File menu of Word 2000.

1.15

2 “Print dialog box” will appear.Confirm that “Doc Pilot ix3010 PCL6” has been selected, then clickProperties.

3 “Doc Pilot ix3010 PCL6 Properties” screen will appear.

4 Adjust the printer settings as you see fit. (See “Printer settings,”page 1.19.)

1.16

From the printer icon

1 Click Start and then click Printers and Faxes.

If you are using Windows XP Home edition, click Start, ControlPanel, Printers and Other Hardware, then click Printers andFaxes.

In other version of Windows, click Start, Settings, then clickPrinters.

2 Right-click the Doc Pilot icon, and then click Properties (Windows95/98/Me), Document Defaults (WindowsNT 4.0), PrintingPreference (Windows 2000/XP).

Windows XP

1.17

Windows 95/98/Me

Windows NT 4.0

Windows 2000

1.18

Printer settingsNow you can access the various windows of the driver by selecting thetabs at the top of the screen.

1.19

Output Image:It shows a sam-ple image howthe documentwill be printedout with speci-fied settings.

Cancel:Close the dialogbox withoutsaving anychanges youhave made.

Apply:Saves all thechanges youhave madewithout closingthe dialog box.

Help:Click to displayonline help.

OK:Close the dialogbox and saveany changesyou have made.

Default:Click to resetthe driver set-tings exceptDevice Optionsettings to thedefault setting.

Printer driversetting items

Tabs:Click to change the setting of menu display.

1.20

Paper tab

Zoom setting

Fit to Paper:Use this option to print a document on a different sized paper than thedocument’s size, for example, Letter-sized document to be printed on A4-sized paper. Select the desired paper to be printed from the paper list,and the document will be printed out on the selected paper automatically.

Scale to fitCheck this box if you want your document to be fitted to the selectedpaper size. The document will be reduced or enlarged automatically to fitto the selected paper.Note:When Combine function is selected, “Fit to Paper” cannot be set.

Scaling(%)You can enlarge or reduce the document in 1 percentage increments, from50 to 200. The scaling ratio refers to the document paper size (Check yourapplication’s page size settings). When enlarging, only the portion of thedocument that remains within the page will be printed. When reducing,white space may appear on the paper.Note:When Scale to Fit (to the paper size) or Combine function is

selected, “Scaling (%)” cannot be set.

1.21

Copies setting

Copies:Enter the number of copies (1-99) you want to print, and select the Sort onor off.Note:The setting in your application software may override the setting in

the printer driver

Sort setting

Sort:When you check this option to be On, multi-page job will be printed in collated sets. When Off is selected, it will be printed on a page-by-pagebasis.

Orientation setting

Orientation:Specifies how the document is positioned on the page. Portrait orients theprint vertically. Landscape orients the print horizontally.

Paper Size setting

Paper Size :Use this option to select the paper size of your document. Select the papersize of your document from the drop list, which shows the paper sup-ported in the printer driver’s current setting. Paper Sizes areconstrained by the Paper Source and Combine settings. If you cannotfind the objective size in the list, change the settings of paper source.Note that the setting made in some application software may override thedriver’s settings, so it is recommended to fit the driver’s settings to matchapplication software settings.Note:For details on the paper sizes your machine supports, see “Paper”

on next page.

1.22

PaperThe ix3010 printer driver supports printing on the following paper size.This also indicates the paper source where each paper can be loaded.

Inch version:Paper Size C1 C2 Bypass Tray

Legal (S) 8.5″ × 14″ Yes Yes Yes

Letter (S) 8.5″ × 11″ Yes Yes Yes

Half Letter (L) 8.5″ × 5.5″ Yes Yes Yes

Executive (S) 7.25″ × 10.5″ No No Yes

A4 (S) 210 × 297 mm No No Yes

A5 (S) 148 × 210 mm No No Yes

A5 (L) 210 × 148 mm No No Yes

A6 (S) 105 × 148 mm No No Yes

F4 (S) 210 × 330 mm No No Yes

COM 10 (S) 4.125″ × 9.5″ No No Yes

Monarch (S) 3.875″ × 7.5″ No No Yes

DL (S) 110 × 220 mm No No Yes

Postcard (S) 100 × 148 mm No No Yes

Custom Paper ScanningNo No

97 mm to 216 mmDirection 3.82″ to 8.5″Feed

No No140 mm to 356 mm

Direction 5.5″ to 14.0″(1 inch = 25.4 mm)

S: Short edge feeding, L: Long edge feedingC1: 1st paper cassetteC2: 2nd paper cassette

1.23

mm version:Paper Size C1 C2 Bypass Tray

Legal (S) 8.5″ × 14″ No No Yes

Letter (S) 8.5″ × 11″ No No Yes

Half Letter (L) 8.5″ × 5.5″ No No Yes

Executive (S) 7.25″ × 10.5″ No No Yes

A4 (S) 210 × 297 mm Yes Yes Yes

A5 (S) 148 × 210 mm No No Yes

A5 (L) 210 × 148 mm Yes Yes Yes

A6 (S) 105 × 148 mm No No Yes

F4 (S) 210 × 330 mm Yes Yes Yes

COM 10 (S) 4.125″ × 9.5″ No No Yes

Monarch (S) 3.875″ × 7.5″ No No Yes

DL (S) 110 × 220 mm No No Yes

Postcard (S) 100 × 148 mm No No Yes

Custom Paper ScanningNo No

97 mm to 216 mmDirection 3.82″ to 8.5″Feed

No No140 mm to 356 mm

Direction 5.5″ to 14.0″(1 inch = 25.4 mm)

S: Short edge feeding, L: Long edge feedingC1: 1st paper cassetteC2: 2nd paper cassette

1.24

Custom paper size settings

Edit Custom:Click this button when you want to add, change or delete your custompaper size. You can add up to 50 custom paper sizes.Note:This button is available when the Paper Source is set to the

Bypass Tray, and the Combines setting has not been selected.

To add a custom paper size:

1 Click Edit Custom.

2 Click Add.

3 Enter the name that identifyyour custom paper. You canenter up to 20 characters.

4 Specifies the width and length ofyour custom paper size.

5 Click OK.

To delete a custom paper size:

1 Select the paper name that you want to delete from paper namelist.

2 Click Delete.

Paper source setting

Paper Source:This setting specifies the cassette or the tray from which the recordingpaper is supplied.You can select the following paper source:• Auto• Bypass Tray• 1st Paper Cassette• 2nd Paper Cassette (if installed)If an objective paper cassette/tray is not listed, go to the Device Optiontab and add it.When you set the Paper Source to Auto, the suitable paper fitted to thesetting of Paper Size and Paper Type will be selected automatically.

1.25

Note:Some of the application software’s settings may override the set-tings in the printer driver.

Paper Destination setting

Paper Destination:Use this option to select the desired paper destination for the print job.The default setting is the Paper Tray. Valid choices include Paper Trayand an additional paper-handling device 2-Bin Tray, if installed on theprinter.Note:If a 2-Bin Tray is not installed, it will not appear in the Paper

Destination drop down list.

Paper Type setting

Paper Type:This option allows you to choose the paper type of the print paper. Byselecting the paper type here, you can get the best print quality for eachpaper type.You can select the following paper type:• Plain• Pasteboard/Labels• OHP• Envelopes/PostcardNote:Special paper such as pasteboard, OHP sheet and envelope/ post-

card can be selected when the Paper Source is set to Bypass Trayor Auto.

Reverse Printing

Reverse Printing:Specifies the order in which the pages of your document will be printed.When Reversing Printing is selected, your machine will print the docu-ment so that page 1 is on top of the stack.

1.26

Page Layout tab

Combine setting

Combine:Specifies how many pages of your document will print on one piece ofpaper.You can print 2, 4 or 8 pages of your document onto one sheet of paper.Note:Before setting this function, make sure that the scaling is set to

100%. Once the Combine function is set, the scaling will be deter-mined automatically and it cannot be changed manually. If you getan unexpected result when printing a multiple-page documentusing this function, check the Sort option off and reprint your docu-ment.

Print Separator Line:You can draw separator lines around each page printed on the sheet,when you set the Combine (2, 4 or 8 pages in 1) function.

Detail of CombineClick this button to open the Detail of Combine dialog in which you canspecify the order of combined pages on the paper. The detailed setting youselect can be viewed in the Output Image display.

1.27

Watermark setting

Watermark:You can print Watermark text (such as “Confidential” and “Sample”) overdocument. Choose the desirable watermark from the drop down list.

Click Edit Watermark to edit, create or delete watermarks.

To create the new watermark:You can register up to 20 types of watermark in this dialog. (The 11 typesof watermark have already been registered.)

Click Add. “Watermark” will be displayed automatically.

Enter the name of your new watermark.You can enter up to 30 characters.

Enter the letters you want to print.You can enter up to 30 characters.

Create a setting for your new watermark.If you need help, click Help.

Click OK to save it.

1.28

Quality tab

Toner SavingSelect toner saving to On to reduce the toner consumption of the printer.

ResolutionThe resolution setting determines the dots per inch used when a docu-ment is printed.

True Type ModeDownload as OutlineThis is the default setting. Most print jobs increase printing speed.

Download as BitmapSelect this mode if graphics are not printed properly as the computerscreen. Note that the printing speed may decrease in this mode.

Download as GraphicsSelect this mode when the document contains graphics and texts togetheron a page. This option is also useful to expose the text which is over-lapped on the graphic background.

1.29

Graphics ModeOnly for Windows 95/98/MeUse the Graphics Mode Setting to tell Windows how to send graphicsinformation to the printer. The Vector mode increases the data transferand printing speed by encoding the image data, but reduces the imagequality in certain cases compared with the Raster mode which causes theraw image data to be transferred in raster or bitmap form to the hostcomputer. Select one of the two options in the Graphics Mode Settingsbox:

VectorSends graphic data to the printer as a mixture of Vector and Rasterimages.

RasterSends all graphics to the printer as Raster images.

Note:When scaling, select Graphics Mode to Vector, and True Type Modeto Download as Outline.

1.30

Device Option tab

2nd Paper CassetteWhen the optional second paper cassette is installed, check this checkbox.The cassette will be added to the Paper Source box in the Paper tab.

2-Bin TrayWhen the optional 2-bin tray is installed, check this checkbox. The traywill be added to the Paper Destination in the Paper tab.

Total Memory for PrinterEnter the amount of memory in your printer.

Automatic Setup Current Option UnitsCheck this box to make the driver recognize which optional devices havebeen installed on the printer. To use this function, run the RemoteShuttle in advance.

1.31

Device ImageYou can see a graphi-cal representation ofthe currently config-ured options on theprinter.

Using the Remote Shuttle

About Remote ShuttleRemote Shuttle is the software utility that monitors the printer status.It helps you quickly determine the cause of problems and tells you whatyou need to do to correct them.Also, you can set the printer settings from your PC using the RemoteShuttle. (See page 1.34.)Note:The Remote Shuttle does not work in a network environment.

It only works for a printer directly connected to your PC with a bi-directional parallel cable.

Installing the Remote ShuttleYou can install the Remote shuttle by using setup.exe, please refer to the“Installing using setup.exe,” page 1.3.

Start the Remote ShuttleTo start the Remote shuttle:

1 Click Start, and point to All Programs > Doc Pilot.

2 Click Remote Shuttle ix3010.

Note:If you set up the Remote Shuttle to start automatically, it will startautomatically when Windows is started.

1.32

Remote Shuttle screenThe following is an example of a screen produced by Remote Shuttle.

Reduced view:

Enlarged view:

Remote Shuttle iconClicking the Remote Shuttle icon on the task bar will allow you to openand close the Remote Shuttle screen.

When you point to the Remote Shuttle icon using the cursor, it will showthe printer’s status. If a printer error occurs the icon’s color will change tored or yellow.

1.33

Printer setting from Remote ShuttleUse this setting mode, if you are using the DOS applications or want toselect the settings which are not included on the printer driver settingfrom the application software or printer icon.

The priority of the setting is as follows:1. Printer driver setting from application software2. Printer driver setting from printer icon3. Printer setting from Remote Shuttle

Open the Printer setting screen

1 Click Printer Setting from the Setup menu on the reduced viewscreen, or click the Printer Setting button on the enlarged viewscreen of the Remote Shuttle.

2 The printer setting screen will appear.

Note:When a printer error occurs, the printer setting screen cannot beopened.

1.34

Paper tab

Paper SizeSelect the paper size of your document from the drop list, which shows thepaper supported in the printer driver’s current setting.

Paper Type:Choose the type of paper. By selecting a paper type here, you can get thebest print quality for each paper type.

Paper SourceSpecify the cassette or tray from which the recording paper is supplied.When you set Paper Source to Auto, the suitable paper fitted to the set-ting of Paper Size and Paper Type will be selected automatically.

Paper DestinationSelect the desired paper destination for the print job.The default setting is Paper Tray. Valid choices include Paper Tray andthe additional paper-handling device 2-bin tray, if installed on the printer.Note:If a 2-bin tray is not installed, it will not appear in the drop down list.

OrientationSpecifies how the document is positioned on the page. Portrait orients theprint vertically. Landscape orients the print horizontally.

CopiesEnter the number of copies you want to print. You can select from 1 to 99copies.

1.35

Printer setting tab

Page ProtectionWhen Page Protection is set to Auto, the printer decides if it executesPage Protection on each page automatically. When Page Protection is setto On, the printer starts to print after each page is stored into memory.Please select Auto, since the printing speed is usually slower when On isselected. If the page is not printed out correctly (printer overrun occurs)at Auto setting, please try to print again after selecting On.

Toner SavingThis is to control the toner saving by selecting either On or Off. You cansave the toner when you select On, though the print density is lighterthan Off setting. The default setting is Off.

I/O Time OutYou can set the time (second) until the printer judges as time out errorwhen it receives the data. The printer cancels the print job automaticallyif it does not receive the data within the time you set.

FormThis is to set the number of lines one page will include. You can selectfrom 5 to 128 lines.

Auto ContinueThis is to set whether the printer will be checked after a warning statusmessage appears. You can select the following selection:

1.36

Off— A message is displayed and the printer goes off line until you pressthe Start key on your printer.

On— A message is displayed and the printer waits a predeterminedinterval time before resuming the printing automatically.

Time Out— You can change the interval time that the printer will waitbefore it starts to print automatically after the warningmessage appears.

ResolutionThe resolution setting determines the dots per inch should be used whena document is printed.

PCL font tab

Font NameYou can select a desired font that is available on the printer.

Font NumberThe printer displays a Font Number that is assigned to each font. If youchange the Font Number, the font and the point of font is changed to theselected one.

Symbol SetYou can select a desired Symbol Set from the available fonts that installedon the printer.

Font PitchThis item will appear, depending on the selected font. A value can bechanged setting by increments of 0.01 for Pitch.

1.37

Font Point SizeThis item will appear, depending on the selected font. A value can bechanged setting by increments of 0.25 for Point Size.

Test print tab

Print Demo PageYou can print the page that demonstrates the features of the printer byclicking this button.

Print Printer Configuration ListYou can print the list that shows the configuration of the printer by click-ing this button.

Print Font ListYou can print the list of the PCL fonts that are installed in the printer byclicking this button.

Print NIC Configuration ListYou can print the list of the NIC Configuration by clicking this buttonwhen the NIC option is installed.

1.38

Net setting tab

Note:The Net Setting is available only when the optional network inter-face card is attached to your machine.

Note:When configuring these settings, contact your network administra-tor.

IP AddressType the IP Address obtained from your network administrator.

Subnet MaskType the Subnet Mask obtained from your network administrator.

Default GatewayType the number of Default Gateway.

Ethernet Frame TypeSelect Ethernet frame type.

1.39

Configuration tab

Total Memory for PrinterThis shows the amount of memory on the printer controller board exclud-ing one for your machine. The standard memory is 16MB. You can installup to max. 144MB. Contact Imagistics for memory upgrades.

Installed OptionsA mark will appear in the check box of options that installed on theprinter.

1.40

Canceling the printing job

ONLINE keyWhen the Printer driver has been installed to the ix3010, the leftmostSoft key will be changed to the ONLINE key.The ONLINE key is used for the canceling of PC printing.

To cancel a print job

During PC printing, the following display will appear on the ix3010’s dis-play, and the LED on the ONLINE key will blink.

If you want to cancel the current printing job, follow the instructionsbelow:

1 Press the ONLINE key on the control panel. These messages willalternate on the LCD:

and

2 If you wish to cancel the current print job, press ENTER.If you do not wish to cancel the current print job, press CANCEL.

Cancel PC Print?No Cancel

Cancel PC Print?Yes Enter

ONLINE

ONLINE key

PC PrintingPage 1

ONLINE

ONLINE key

1.41

Using your machine on a Network

Connection through print server PC

When equipped with a printer controller, your ix3010 can also be madeavailable to other network users by connecting it to the network througha print server PC. In this arrangement, the ix3010 with the printer con-troller is connected to the print server PC using a bi-directional parallelprinter cable. The print server PC is connected to the network through anetwork interface card inside the PC.The print server PC must be turned on, in order for the networkedImagistics fax to be used as a printer.

EtherNet

Print Data

Print Server PC

1.42

Connecting through optional network interfaceWhen equipped with the printer controller and an optional network inter-face card, your fax machine can also be connected to the followingnetwork environment.When you plan to use your fax machine as a PC printer in one of thesenetwork environments, you must setup the network settings as shown onthe following page.❑ Peer to Peer networkThe ix3010 can be used on a peer-to-peer network operating withWindows NT® 4.0 workstation, Windows® 95/98/Me, Windows® 2000 andWindows® XP PCs.

❑ Client/Server networkThe ix3010 can be used on a client/server network operating withWindows NT® 4.0 workstation, Windows® XP, Windows® 2000, Windows®

95/98/Me and Windows® 3.1x clients, with Novell Netware® 2.x/3.x/4.x,Windows NT® 4.0 server on the server.

Print Data

Print Data

Print Server PC

Client PC

EtherNet

EtherNet

Print Data

1.43

EtherNet connectionWith the optional network interface card installation, a 10/100Base-TEtherNet port will be added to your fax machine.To connect to the network:

1 Turn off your fax machine.

2 Connect the network cable to the Ethernet port.

3 Connect the other end of the network cable to the Ethernet.

Note: If you need help with this step, contact your network admin-istrator.

4 Turn on your fax machine.

Entering the IP Address When you use the TCP/IP protocol, you must enter an IP Address, Subnetmask and Default Getaway for network usage. See “Set TCP/IP,” page1.48.Note:If you need help, contact your network administrator.

EtherNet port Network cable(10/100Base-T twist pair cable)

1.44

Software License AgreementREAD BEFORE INSTALLATION

This Software License Agreement (hereinafter the “Agreement”) is a legal contractmade between you (regardless of an individual or a legal entity) and our company(“Imagistics International Inc.”) regarding software products contained in this CD-ROM (hereinafter the “Software”).

Please read the following terms carefully before installing the Software. You can installand use the Software subject to your acknowledge and acceptance of all of the followingterms. If you do not agree to any of the following terms, you should cancel the installingprocess.

The condition of the software license:1. Any and all copyright and any other intellectual property regarding the Software

remain solely the property of NETsilicon Inc. (hereinafter “NETsilicon”).

2. You may use the Software only in the country of your purchase and only when usingour companies’ hardware.

3. You must not modify, alter all or any part of the Software. You must not make anyattempt to discover the source code of the Software by any method includingreverse-engineering, de-compiling, or de-assembling.

4. You must not sell, transfer, rent, lease or sublicense the Software to any third partyby transmitting the software via phone-line or network, or by copying the softwareto floppy disk, CD-ROM, magnetic data tape or any other media.

5. The software is subject to changes by NETsilicon in its specifications and programwithout any prior notice.

6. Before installing the software, you are supposed to take any and all procedures nec-essary to secure your records and data at your cost and responsibility, includingmaking backup of your computer files. Neither our company, our distributors/sub-distributors nor NETsilicon shall be liable for any damage or loss caused by yourfailure of taking the foregoing procedure.

7. Neither our company, our distributors/sub-distributors nor NETsilicon shall beliable for any damage or loss caused by (1) use of the software in combination withthe hardware other than the hardware which is defined in Section 2 above or (2)modification of the software.

8. Neither our company, our distributors/sub-distributors nor NETsilicon shallassume any damages incurred by you or a third party even if such damage isdirectly/indirectly caused by use of the software or incapability to use the soft-ware.

If you acknowledge and acceptance of all of them, install the software following steps.

1.45

Installing the software for your network environmentBefore you install the software, please see the Software LicenseAgreement on page 1.45.

To install the software:

1 Insert the CD-ROM included in the optional NIC package into yourCD-ROM drive.

2 The following screen will appear automatically.

3 If your PC does not have Adobe Acrobat Reader installed on it,please install it. To install Acrobat Reader, click Install AcrobatReader on the screen.

4 After you install Acrobat Reader, click Go to the CD ROM Tableof Contents on the screen. Acrobat Reader will run and the follow-ing screen will appear.

1.46

5 Click the item on the screen and install the software suitable foryour network environment by following the instructions thatappear on the screen.

Note:For details on how to use the settings and buttons, see on-line help.

Note:The Imagistics NIC (network interface card) is not supported by the following protocols.• IPX-P2P in Windows® NT, Windows® 2000 and Windows® XP• IPP in Windows® 2000

To remove the software

1 Close the software you want to uninstall.

2 Click on Start>Settings>Control Panel, then selectAdd/Remove Programs. The Windows® Add/Remove Programsproperties box will appear.

3 Select software you want to remove, then click the Add/Removebutton.


1.47

Set TCP/IPWhen using the TCP/IP protocol, enter the IP Address, Subnet mask andthe default Getaway.Note:To access this function, the optional NIC (Network Interface Card)

must be installed. Contact your network administrator if you haveany questions about these settings.

To enter your network settings:

1 Press Program key, B, 4, 0, 1.

2 Press ENTER. The LCD will show:

3 Enter the IP Address for your printer using the numeric keypad,then press ENTER to save the setting.For example, if your printer’s IP Address is 200.1.37.47, you shouldpress 2 0 0 0 0 1 0 3 7 0 4 7.


5 Enter Subnet Mask address.


7 Enter default Gateway.

8 Press ENTER to save the setting. The machine will return tostandby mode.

9 To effect the TCP/IP setting, turn the machine off and then backon.

Set Default Gateway000.000.000.000

Set Subnet Mask000.000.000.000

Set IP Address000.000.000.000

01 TCP/IP/ /Enter

1.48

Error MessagesThe following message will be displayed on the LCD of the printer whenprinter error occurs.

Message Meaning

Paper Mismatch Cassette paper size does not match the specified Start/Stop/CopyReset paper size.

•Change the paper in paper cassette or papersource.

•If you press STOP, the printer will cancel the current printing job.

•If you press COPY RESET, the printer will cancelall printing jobs stored in its memory.

(See “Paper Mismatch error,” page 1.52.)

Drawer Size Error The paper size you specified cannot be set in theStart/Stop/CopyReset paper cassette.

•Use the bypass tray. To select the bypass tray,press START then select “Tray” by pressingPAPER SIZE?. Set the specified paper in bypasstray.


•If you press COPY RESET, the printer will cancelall printing jobs stored in memory.

(See “Drawer Size Error,” page 1.53.)

Memory Overflow The printer received more data from the Start/Stop/CopyReset computer than it can fit in memory.

•Press START to continue, but there may be somedata loss.



Print Overrun Data sent to the printer is too complex.Start/Stop/CopyReset •Press START to continue, but there may be some

data loss.•If press STOP, the printer will cancel the current

printing job.•If you press COPY RESET, the printer will cancel

all printing jobs stored in memory.

1.49

Message Meaning

Unable To Sort The data is too large to sort.Start/Stop/CopyReset •If you press START, the printer will print only

the document stored in its memory without sorting.


•If you press COPY RESET, the printer will cancelall printing jobs stored in its memory.

Option Install Error The optional paper cassette or 2-Bin tray are not Start/Stop/CopyReset installed.

<2-Bin tray>•Press START. The printer will print your docu-

ment.<2nd paper cassette>•Press START then select correct paper source by

pressing PAPER SIZE. And then press START

again to start printing.•If you press STOP, the printer will cancel the

current printing job.•If you press COPY RESET, the printer will cancel

all printing jobs stored in its memory.(See “Option Install Error,” page 1.54.)

Please Supply Paper The printer has run out of paper.Stop/CopyReset •Add the appropriate type of paper.



Please Replace Drum The drum cartridge has reached the limit of itsStop/CopyReset design life.

•Replace the drum cartridge.•If you press STOP, the printer will cancel the

current printing job.•If you press COPY RESET, the printer will cancel

all printing jobs stored in its memory.

Please Replace Toner Your toner cartridge is empty.Stop/CopyReset •Replace the toner cartridge.



1.50

Message Meaning

Close 1st Cassette Paper cassette is open.Stop/CopyReset •Close it.



PCL: System Error XX An internal controller error has occurred.Turn the printer off then back on. If the errorappears again, contact Imagistics.

1.51

Paper Mismatch errorIf the size of paper in paper cassette does not match the document size,you want to print, the following message will appear on your LCD:

To start the printing:

1 Press START.

Paper size of the selected paper cassette.Document size you want to print

2 Change the paper in the paper cassette you selected (if necessary,see your fax machine’s operating instructions). Then pressPROGRAM and select the same sized paper using the cursor key.After you change the paper, press ENTER. Your machine will startthe printing automatically.–or–If another paper source (e.g. 2nd cassette) has the correct sizepaper for the print job, press PAPER SIZE key to select it. Then pressSTART to start printing.

Note:If you want to print on the paper that is not available on yourpaper cassette, use the Bypass tray.To know what size paper is available for your paper cassette, see“Paper” on pages 1.23—1.24.

To cancel printing job:If you want to cancel the current printing job, press STOP.If you want to cancel all printing jobs stored in your machine’s memory,press COPY RESET.

Select Paper SourceLegl Ltr

Paper MismatchStart/Stop/CopyReset

1.52

Drawer Size errorIf the paper you select is not acceptable for the paper cassette (see“Paper,” pages 1.23—1.24), the following message will appear on yourmachine’s LCD:

To start the printing:

1 Press START.

Paper size of the selected paper cassette.Document size you want to print.

2 Press PAPER SIZE to select the bypass tray.

3 Set the paper in bypass tray and select thepaper size (if necessary, see your machine’s operating instructions).Then press START to start printing.

To cancel this printing job:If you want to cancel the current printing job, press STOP.If you want to cancel all printing jobs stored in your machine’s memory,press COPY RESET.

Select Paper SourcePost None

Select Paper SourcePost Ltr

Drawer Size ErrorStart/Stop/CopyReset

1.53

Option Install errorIf you tried to print with the optional 2nd paper cassette or the 2-Bin traywhen they have not been installed, the following message will appear onyour LCD:

To start the printing:<2-Bin tray>

Press START. The printer will start printing.

<2nd paper cassette>

1 Press START.

2 Press PAPER SIZE to select the 1st papercassette or the bypass tray.

If you select the 1st paper cassette, youcan change the paper size by using the following procedures:While you select the 1st paper cassette, press PROGRAM then selectthe paper size using the cursor key and then press ENTER.

3 Press START to start the printing.

To cancel this printing job:If you want to cancel the current printing job, press STOP.If you want to cancel the all printing jobs stored in your machine’s mem-ory, press COPY RESET.

Select Paper SourceLtr Ltr

Option Install ErrorStart/Stop/CopyReset

1.54

Uninstalling

Uninstalling the Doc Pilot and Remote Shuttle

Note:To uninstall the printer driver software from Windows NT®,Windows® 2000 or Windows® XP, you must be logged in as theadministrator.

1 Close the Remote Shuttle, if it is running.

2 To start the Doc Pilot uninstaller program,click Start > All Programs > Doc Pilot, then clickDoc Pilot ix3010 Uninstaller.

2 Click Yes when uninstall program asks you to confirm.


Note:Uninstaller program is available when a driver was installed usingsetup.exe only. When the driver was installed from “Plug and Play”or “Add Printer Wizard”, open the Printers window, right-click onthe Doc Pilot icon and click Delete.

1.55

Appendix

Print the Demo PageThe demo page provides a demonstration that highlights the features andfunctions of the printer.

To print the demo page:

1 Press Program key, E, 2, 0, 1.

2 Press ENTER to print the demo page.

Print the Printer Configuration PageThe printer configuration page lists the status and configuration of yourmachine.

To print the printer configuration page:


2 Press ENTER to print the printer configuration page.

Print PCL Font ListThe PCL font list provides a list of all PCL fonts currently installed inyour machine.

To print the PCL font list:


2 Press ENTER to print the PCL font list.

03 Font List/ /Enter

02 Status Page/ /Enter

01 Demo Page/ /Enter

1.56

Print NIC status

Note:To make this function available, the optional NIC (NetworkInterface Card) must be installed.

To print the NIC status:


2 Press ENTER to print the NIC status.

AGFA Font Manager 2000AGFA Font Manager 2000 helps you manage your fonts in MicrosoftWindows.Note:AGFA Font Manager 2000 requires Windows® 95/98, Windows® Me,

Windows NT® 4.0, Windows® 2000 or Windows® XP.It is not available on Windows 3.1

To install:

1 Insert the Imagistics Printer driver CD into your CD-ROM drive.

2 Click Start, then click Run.

3 Type <Drive>:\Font\Setup.exe<Drive> is the drive letter for your CD-ROM drive.

You can also browse through the folders to find the Setup.exe fileby clicking Browse button.

4 Click OK to start the software installation program.


Using the font manager 2000:For full details about how to use AGFA Font Manager 2000, click theHelp button on the AGFA Font Manager 2000 window.

04 NIC Status/ /Enter

1.57

Chapter 2

Using your machine as ascanner

This TWAIN-compliant scanner driver is developed by Destiny TechnologyCorporation and is protected under the Copyright Law in various countries. Copy,distribution, modification, use or any other disposal thereof is not allowed unlessotherwise authorized in this manual.

System requirements

2.1

The following are the minimum computer requirements to install andoperate the Imagistics TWAIN driver.

Supporting PC:IBM-PC / AT Compatible

CPU: i486DX/66MHz or higherNote: We recommend Pentium/150MHz or higher.

Operating System:Windows® 95/98/Me, Windows NT® 4.0, Windows® 2000 orWindows® XP

Hard Disk Drive:At least 10MB of available disk space for installing

RAM: At least 32 MB

Application Interface:TWAIN Driver compatibleTWAIN Driver Version: Version 1.9

Terminal Connector Interface:A bidirectional parallel interface IEEE1284 (Compatiblemode / Nibble mode / ECP mode)

Supporting Application Software:Application software which supports TWAIN.We have tested the following packages:· I.R.I.S. Readiris PRO 6· ScanSoft PaperPort DELUXE 7.0· Wordcraft Unimessage Pro Version1.0· Wordcraft Unimessage XLite Version1.1· Adobe Acrobat Capture 3.0· ScanSoft TextBridge Pro Millennium Version9.5· Caere OmniPage Pro 10.0· Microsoft Word 2000· Microsoft Excel 2000· Microsoft PowerPoint 2000· Kodak Imaging for Windows 95/98/Me/2000

Note:Actual requirements will vary based on your PC system configura-tion, the applications and the image you will scan.

Follow the steps below to install the Imagistics TWAIN driver for Windows® 95, Windows® 98, Windows® Me, Windows NT® version 4.0,Windows® 2000 or Windows® XP.Before you install the software, please read the README. TXT file in theappropriate directory of the CD-ROM for important installation informa-tion and helpful hints:

<Drive>:\Scanner\<Windows version>\Readme.txtNote:<Drive> is the drive letter for your CD-ROM drive.

In <Windows version>, the following folder name will be appliedaccording to your Windows version:

• Win9x_Me : for Windows 95/98/Me• WinNT4_2000 : for Windows NT® 4.0 and Windows® 2000• WinXP : for Windows® XP

To install the Imagistics TWAIN driver

1 Start Windows.

Note: If you are using Windows NT® 4.0, Windows® 2000 orWindows® XP, you must log in as the administrator to install(or uninstall) the Imagistics TWAIN driver.

2 Insert the Imagistics Printer driver CD into your CD-ROM drive.

3 Click Start and then Run.

4 Type <Drive>:\Scanner\<Windows version>\Setup.exe.

Note: <Drive> is the drive letter for your CD-ROM drive.<Windows version> is the folder name which means yourWindows’ version. (See above.)

You can also browse through the folders to find the Setup.exe filefor your version of Windows® by clicking Browse.

5 Click OK to start the installer software.


To uninstall the Imagistics TWAIN driver

1 To start the uninstaller program, click on Start>Settings>Control Panel>Add/Remove Programs,select Imagistics TWAIN Driver and click on Add/Remove.


2.2

Installation

Before you use the Imagistics TWAIN driver, the following must be true:• The ix3010 is connected to your PC using the bi-directional parallel inter-

face cable.• The Imagistics TWAIN driver has been installed on your PC.• You must have software that supports TWAIN scanning.

(See page 2.1)

Important information regarding the Imagistics TWAINdriver

Scanning modeImagistics’ TWAIN scanning let’s you scan documents two different ways:• Real-time scanning mode (RS mode)

When you use the real-time scanning mode, or RS mode, yourImagistics machine will scan and transfer document images to yourPC immediately. RS mode is the mode most like traditional documentscanners.

• Scan-box mode (SB mode)When you choose the scan-box mode, or SB mode, your Imagisticsmachine will scan and store the image data into a scan box. You canretrieve the scanned data from the scan box by using the TWAINdriver anytime.

Scanner settingsYou should confirm the following settings before scanning. If youchoose RS mode, make these settings from your PC. If you choose SBmode, set them using the control panel on your Imagistics machine.Regarding the initial settings and details, refer to “The list of scannersettings” on page 2.27.

• Scan size — Set the size you will scan.• Document type — Set the document type according to the document

you want to scan. You can select from:Photo — Select this mode when scanning photographs or drawings.Photo/Text — Select this mode when scanning documents containing

photographs or drawings and text.Text — Select this mode when scanning text.

• Contrast — Sets how light or dark you want the documents to be.

2.3

Getting ready to use theImagistics TWAIN driver

• Resolution — You can choose to scan at 200 dpi, 300 dpi, 400 dpi or 600 dpi resolu-tion. Scanning at 600 dpi provides greater detail in scanned images,but creates large files and uses more memory in your PC and yourImagistics machine.Note: Scanning enlargement is not available at 600 dpi.

• Reduce/Enlarge — You can reduce or enlarge the document once itis scanned. Select one of the preset rates, or enter the desired ratio by1 percent increments.Note: The enlargement is available only for scanning using the FlatBed

Scanner(FBS). It is not available for scanning through the AutomaticDocument Feeder(ADF).

Changing your machine to the Scanner mode

Press the COPY/FAX/SCAN key until both the COPY light and FAXlight turns off.

PriorityThe Imagistics Printer driver CD allows you to use the ix3010 as a PCprinter and a PC scanner through the unit’s single bidirectional parallelinterface port. It is, however, not possible to use both functions at once. Inorder to avoid conflict between these two functions while using theImagistics TWAIN driver while the Remote Shuttle is working, theTWAIN driver will request to close the Remote Shuttle.

Copy/Fax/Scan key

2.4

Access to the Imagistics TWAIN driverFollow the steps below to access the Imagistics TWAIN driver from yourapplication software:

1 Turn on the ix3010.

2 Start the application software that supports TWAIN scanning.

3 Select “Imagistics TWAIN Driver” in your application software. (Ifyou need help, refer to your software’s help file.)

If you use the Microsoft Word 2000, click “Insert” on the menu bar,then select “Picture” then “From Scanner or Camera”. Choose“Imagistics TWAIN Driver” then click Custom Insert. The follow-ing window will appear:

When you want to use the RS mode, select “RS mode” tab.When you want to use the SB mode, select “SB mode” tab.When you want to see information about the Imagistics TWAINdriver, select “About” tab.

Note:“Type 2” at the top of the window means your machine is ix3010.

2.5

Scanning the image

Using the RS mode

Scanning with the RS mode

1 Follow the steps in “Access to Imagistics TWAIN driver” on page 2.5to display the following window:

2 Select the desired elements for each setting. (Refer to “The list ofscanner settings” on page 2.27, if necessary.)If you want to Reduce/Enlarge by 1 percent increments, click thecheck-box next to “Zoom” and enter a ratio.

Note: The enlargement is available only for scanning using theFlatbed Scanner(FBS). It is not available for scanningthrough the Automatic Document Feeder(ADF).

Note: You can choose to scan at 200 dpi, 300 dpi, 400 dpi or 600 dpiresolution. However, the scanning enlargement is not avail-able at 600 dpi. Select other resolution, or select 100% forthe ratio.

2.6

Definition of the Windows buttons:OK — When you have finished adjusting the settings, click thisbutton.Cancel — If you want to close the window without scanning,click this button.Default — If you want to set all values to default, click this button.Help — If you want to see the on-line help, click this button.

3 On your machine, change the machine’s mode to scan mode bypressing COPY/FAX/SCAN.

4 Set the document you want to scan.

5 On your PC, click OK to start scanning.The following window will appear:

Note: If you want to cancel the job during scanning or data transfer,click Cancel button.

6 When scanning is complete, the window will close and the scannedimage will appear.

Scan Ready 200dpiLtr 100%

2.7

Using the SB modeThe scan boxes in which the image data will be stored are installed inyour machine. The scan box specifications are as follows:

• Number of Boxes: 20 boxesSet by two-digits from 01 to 20.

• Number of Files/Box: 10 files/box• ID Code: Each box has an ID Code.

Set by four-digits from 0001 to 9999 .

Note:The number of pages which can be stored in a file depends on yourix3010’s memory capacity, the resolution and type of document(s).

The basic operation for the SB modeThe operation for the SB mode is summarized as follows:

1 Create the scan box. (See pages 2.9–2.10.)

2 Scan the document with your machine. The scanned data will be storedinto the scan box. (See pages 2.11–2.12.)

3 Retrieve the scanned data from the scan box. (See pages 2.17–2.19.)

Memory in your machine

Scan Box 1 Scan Box 2 Scan Box 20..........

Scan Box X File 1 File 2 File 10..........

File X Page 1 Page 2 Page ***..........

2.8

Create or modify a scan box

1 Press Program key, C, 6, 0, 1, ENTER. The LCD will show:

2 Use the numeric keypad to enter a desired scan box number.Here, we’ve entered 0, 3 and the LCD will show:

Important: When entering a scan box number less than 10, you mustenter a leading zero to make two digits. For example,01 – 09.

3 Press ENTER.If you want to register the scan box or you have set 0000 for the I.D. codeof this scan box, skip to step 5.If you want to modify the scan box, the LCD will ask you to enter theproper I.D. code. The LCD shows:

4 Use the numeric keypad to enter the 4-digit I.D. code and then pressENTER.Note: If you enter an invalid I.D. code, the fax machine will reject the

attempt and stops the operation.

5 The LCD asks you to enter the scan box name. The LCD will show:

If you have already named the box and do not want to change it, skip tostep 7.If you want to name the box for the first time or change the name, go onto step 6.

03:Box Name;Upper_

03:Set Scan BoxEnter I.D. Code:****

Select Scan Box03:Not Registered

Select Scan Box01:Not Registered

2.9

6 Enter the name by using the one-touch keys. (If necessary, refer to“Entering characters” on pages 2.25–2.26.) A scan box’s name may be upto 16 characters in length.Note: You must enter characters when using a scan box. If you

enter nothing or only spaces, the machine will beep andshow:

7 Press ENTER. The LCD now asks if you want to erase the files in this boxafter transferring them to the PC.

8 Press or until the mode you desire appears.

9 Press ENTER. The LCD now asks for your scan box’s four-digit securityI.D. code. The LCD shows:

If you do not want to change the I.D. code, skip to step 12.

10 Decide on a four-digit I.D. code (0001 – 9999) for this scan box.Write it down, and store it in a safe place.

11 Use the numeric keypad to enter the four-digit I.D. code for the scan box.

Note: If you want to turn off the I.D. code, enter 0000.

12 Press ENTER.

To create or modify another scan box, repeat steps 2–12.To finish, press STOP.

03:Set Scan BoxEnter I.D. Code:0000

Erase Trans Doc :Off/ /Enter

03:Box Name;UpperEnter Box Name

2.10

Scanning the image into a scan box

Important: You should register the scan box before scanning.

1 Press COPY/FAX/SCAN to change to Scan mode.

2 Set the document in the ADF or on the FBS glass.

3 Adjust the following settings. (Refer to “The list of scanner set-tings” on page 2.27, if necessary.)• Scan size — Press DOCUMENT SIZE to select the scan size you want.• Resolution — Press or to select the resolution you want.• Document type — Press DOCUMENT to select the document type you

want.• Contrast — Press CONTRAST to select the contrast you want.• Reduction/Enlargement — Press , or ZOOM to select the ratio

you want. (Refer to the Operating Guide of ix3010, for more details.)

4 Press START. The LCD will show:

5 Use the numeric keypad to enter the desired scan box number.Here, we’ve entered 0, 3 and the LCD will show:

Important: When entering a scan box number less than 10, you mustenter a leading zero to make two digits. For example,01 – 09.

Select Scan Box03:ScanBox3


Scan Ready 200dpiLtr 100%

2.11

6 Press ENTER. The LCD shows:

Note: If you have set 0000 for the I.D. code of the scan box, this messagedoes not appear. Skip to step 8.

7 Use the numeric keypad to enter the scan box’s four-digit I.D. code.Then, press ENTER.Note: If you’ve entered an incorrect I.D. code, your machine rejects the

attempt and returns to standby mode.

8 Your machine will start scanning the document into the scan box.If you are using the ADF, proceed to step 9.If you are using the FBS, skip to step 10.

9 If you have more documents to scan, press NEXT DOC during scan-ning. Then proceed to step 10.Otherwise, the machine will return to the standby mode after it hasfinished scanning.

10 When the scanning is done, the LCD will show:

If you want to scan more pages, proceed to step 11.Otherwise, press ENTER to finish scanning, and the machine will returnto the standby mode.

11 Place the next page.If you want to change the scanner settings, press any of the cursor keys.The LCD will show:

Change the scanner settings as you want, and then press ENTER.(see steps 3 and 4)

Press NEXT DOC to start scanning.

To scan more pages, repeat steps 10–11. (If you’ve used the ADF, repeatsteps 9–11.)Otherwise, press ENTER to finish scanning, and the machine will returnto the standby mode.

03:Store Doc 200dpiLtr 100%

Start Scan →→ NextDocEnd Scan →→ Enter

03:Store DocumentEnter I.D. Code:****

2.12

Erasing a document stored in a scan boxYou can erase a document stored in a scan box two ways; from the PC andfrom your Imagistics machine.

To erase a stored document from the PC:

1 Follow steps 1–5 on pages 2.17–2.18 so that the file you want toerase appears.

2 Click on the file you want and click Delete.

To erase a stored document from your Imagistics machine:

1 Press Program key, D, 2, 0, 4, ENTER The LCD shows:

2 Use the numeric keypad to enter the two-digit number (01-20) of thescan box that stores the document you want to erase. We’ve entered 0, 3:

3 Press ENTER.If you have set 0000 for the I.D. code of this scan box, skip to step 5.Otherwise, the LCD shows:

Note: If the scan box is not storing documents, the machine briefly dis-plays the following before returning to step 2:

4 Use the numeric keypad to enter the scan box’s four-digit I.D. code.Then, press ENTER.Note: If you’ve entered an incorrect I.D. code, your machine will reject

the attempt and returns to the standby mode.

5 The LCD shows:

03:Scan Box DocumentFile No. :_

Select Scan BoxNo Document Stored

03:Scan Box DocumentEnter I.D. Code:****



2.13

6 Use the numeric keypad to enter the file number (1 – 10) of the docu-ment you want to erase. Here we’ve entered 3:

Note: If you want to erase all documents stored in the scan box,enter 0.

7 Press ENTER. The LCD shows:

Note: If you want to quit without erasing any documents in the scanbox, press STOP. The machine will return to the standby mode.

Note: If the file you entered in step 6 does not exist, the machine brieflydisplays the following and then returns to the standby mode.

8 Press ENTER to erase the document(s) and return to the standby mode.

Scan Box Document** Complete **

03:Scan Box DocumentNo Document Stored

03:Scan Box DocumentCheck Enter/Stop

03:Scan Box DocumentFile No. :3_

2.14

Erasing an empty scan boxA scan box must be empty in order to erase it. If you select a scan box that isnot empty, the machine will beep. If this happens, erase all documents in thebox before erasing it.

To erase an empty scan box:

1 Press Program key, C, 6, 0, 2, ENTER. The LCD shows:

2 Use the numeric keypad to enter the two-digit number (01 – 20) of thescan box that you want to erase. Here, we’ve entered 0, 3 and see:

3 Press ENTER.If you have set 0000 for the I.D. code of this scan box, skip to step 5.Otherwise, the LCD shows:

Important: If you select a scan box that is not empty, the machinebeeps and, before returning to step 2, briefly displays:

Erase all documents stored in the scan box, then repeatthis procedure from the beginning to erase the box.Otherwise, select another scan box.

4 Use the numeric keypad to enter the four-digit I.D. code.Then, press ENTER.Note: If you’ve entered an incorrect I.D. code, your machine rejects the

attempt and returns to the standby mode.

5 The LCD shows:

Note: If you want to quit without erasing the scan box you’ve selected,press CANCEL. The machine will return to step 2.

Note: If you want to quit without erasing any scan boxes, press STOP.The machine returns to the standby mode.

03:Erase Scan BoxCheck Enter/Cancel

Select Scan BoxBox In Use

03:Erase Scan BoxEnter I.D. Code:****



2.15

6 Press ENTER to erase the scan box.

To erase another scan box, repeat steps 2–6.To finish, press STOP.

Printing a list of documents stored in the scan boxesTo print a list of document stored in your scan boxes, press Program key,E, 1, 1, 8, ENTER.

Erase Scan Box** Complete **

2.16

Retrieving an image from the scan box

1 Follow the steps in “Access to Imagistics TWAIN driver” onpage 2.5.

2 Select the “SB Mode” tab. You will see:

3 Double click on “ScanBox Top”. You will see:

Note: If the icon next to the scan box is gray, that means there isnot a file currently stored.

2.17

4 Double click on the scan box you want.If the scan box does not have an I.D. code, skip to step 5.Otherwise, the I.D. code dialog box will appear as follows:

Enter the proper 4-digit I.D. code and then click OK.

5 You will see:

The buttons on the dialog box mean:Preview — Select the “File” you want to see, and click this button.You can see the image on the first page of the scanned data.Refresh — Clicking this button will allow you to see the latestinformation in the scan boxes.

2.18

OK — When you want to start transferring, select the “File” youwant and click this button.Cancel — If you want to close the window, click this button.Delete — If you want to delete a file, click on the “File” and clickthis button. After a file is deleted, all files in this box willrearrange from 1 to the maximum file number in this box.Note: You can not delete a scan box with this button.Help — If you want to see the on-line help, click this button.

Note:When you click on a file, you will see detailed information about thefile in the information box.

6 Select the file you want to transfer to the PC and click OK.The following window will appear:

Note: If you want to cancel the job during data transfer, clickCancel.

7 When transferring is complete, the window will close and thescanned image will appear.

2.19

You can change the following initial scanner settings for the SB mode.Regarding the factory settings and details, refer to “The list of scannersettings” on page 2.27.Note:The initial settings for the RS mode cannot be changed except for

the mixed original mode.

Scan parameters — Sets the document type, resolution, contrast, scan sizeand mixed original mode for your documents.Scanner auto reset — Sets the time after which the scanner settings returnto its initial condition automatically.

Scan parametersThe following different settings tell your machine how to scan documentsfor the SB mode. The initial factory settings are probably right for mostapplications, so try using them before changing any of these settings:• Document type — Sets the document type for your documents.• Resolution — Sets the resolution for your documents.

Choose from 200 dpi, 300 dpi, 400 dpi or 600 dpi.• Contrast — Sets how light or dark you want the documents to be.• Scan size — Sets the scanning size for your documents.• Mixed original mode — When setting is ON, the scan size will belong to

the original document size (Max.: 90 cm(35.8 inch)). When setting is OFF,it will be fixed on the size you set in “Scan size” even if the document sizesare various.

Note: The mixed original mode is also available in the RS mode.

To set these modes:See next page.

2.20

Changing the initial settings

1 Press Program key, B, 5, 0, 1, ENTER. The LCD asks you to select a doc-ument type:

2 Press or until the mode you want appears. Then, press ENTER.

3 The LCD asks you to select a resolution:

4 Press or until the mode you want appears. Then, press ENTER.Note: If you select 600 dpi, the scanning enlargement will be not

available.

5 The LCD asks you to select a contrast setting:


7 The LCD asks you to select a scanning size:


9 The LCD asks you to select a mixed original mode:

10 Press or until the mode you want appears.

11 Press ENTER to save the settings.To return to standby mode, press STOP.

Mixed Original :On/ /Enter

Scan Size :Ltr/ /Enter

Contrast :Normal/ /Enter

Resolution :200dpi/ /Enter

Doc. Type:Text/ /Enter

2.21

Scanner auto resetThe scanner settings are initially set to return to their initial condition auto-matically when 10 minutes have passed since you last pressed any key. Youcan, however, change this time from 1 to 10 minutes. Also, you can programthe settings to return to their initial condition as soon as the scanning is com-plete.

1 Press Program key, B, 5, 0, 2, ENTER. The LCD asks you to set the autoreset time:

2 Use the numeric keypad to enter the time you want the scanner to autoreset. Then, press ENTER.Note: Enter a leading zero when entering a quantity less than 10.

3 The LCD will ask if you want the scanner settings to return to their initial condition as soon as scanning is complete.

4 Press or until the mode you want appears.

5 Press ENTER to save the setting.

To finish, press STOP.

Printing a list of scanner settingsTo print a list of your scanner settings:

Press Program key, E, 1, 1, 8, ENTER.A list of your scanner settings will be printed.

Auto Reset** Complete **

Reset After Scan:Off/ /Enter

Auto Reset Time(01-10):03

2.22

Error MessagesThe following message will be displayed on the LCD of your ix3010 when aproblem occurs.

Message Meaning

Memory Overflow The machine scanned more data than it can storein its memory while scanning the first page.•Keep sufficient memory to store documents.•If you press CANCEL, the machine will cancel the

current scanning job.

Memory Overflow The machine scanned more data than it can storeEnter or Cancel in its memory while scanning two or more pages.

•Press ENTER to transfer the data alreadyNote 1 scanned to the computer.

•If you press CANCEL, the machine will cancel thecurrent scanning job.

Open&Close ScanCover An original document jammed while scanningReset Document the first page using the ADF.

orPlaten cover opened while scanning the first page.•Open the scanner cover and remove the docu-

ments in ADF. Then close the scanner cover andreset the documents.

Document Jam An original document jammed while scanningEnter or Cancel two or more pages in RS mode.

orNote 1 Scanner cover, top cover or platen cover opened

while scanning two or more pages in RS mode.•Remove the jammed paper.•Press ENTER to transfer the data already

scanned to the computer.•If you press CANCEL, the machine will cancel the

current scanning job.

Document Jam An original document jammed while scanningContStor Enter/Cancel two or more pages in SB mode.

orNote 1 Scanner cover or platen cover opened while scan-

ning two or more pages in SB mode. •Remove the jammed paper.•Press ENTER to continue the operation•If you press CANCEL, the machine will cancel the

current scanning job.2.23

Error Message

Message Meaning

Mirror Carriage Error The mirror carriage of your machine has becomeinoperable. •Contact Imagistics.

Use FBS Glass You tried to enlarge the documents when scan-ning from the ADF. •Set the documents on the FBS.

Box in Use You tried to erase a scan box which contains atleast one document.

orYou tried to erase a file while transferring.•Erase the document(s), then try again.•After transferring is finished, try again.

Document Full You tried to store a document into a scan box, butthe scan box has reached its capacity (10 docu-ments).•Delete documents stored in scan boxes until the

scan box will let you proceed.

Invalid I.D. Code The scan box’s I.D. code you entered isn’t valid.

Call For Service The scanner lamp is dim or inoperable.•Make repeated copies to help evaporate any

internal moisture. If that doesn’t resolve theproblem, contact Imagistics.

Note 1: If you leave the machine without pressing any key for more than 60 seconds, it willerase from memory all pages stored during this operation and the machine willreturn to the standby mode.

2.24

Entering charactersTo enter letters or other characters for a scan box name, use one-touch keys,numeric keypad or CODE keys.

Using one-touch keys to enter characters

The word “Upper” means the machine will enter only upper-case letters.To type a lower-case letter, press ALPHABET which is one of the one-touch keys.The display changes to:

This means pressing one-touch keys will enter lower-case letters.To switch back for upper-case entries, press ALPHABET.To enter spaces, punctuation and symbols, use the one-touch keys.

Note: If you make a mistake, press CANCEL to erase to the left.To change just one character in the name, press or to move thecursor to that character. Press CANCEL to erase the character. Then re-enter the character correctly.

Using code to enter charactersAlso, you can use the CODE key to enter special characters or symbols.

1 When the machine prompts you to enter a name, press CODE.The LCD changes to:

01:Box Name;Code_

01:Box Name;Lower_

01:Box Name;Upper_

2.25

Appendix

2 Find the character you want to enter in the chart below.

The legends in the black border indicate which key you press, and inwhich order, to get a given character.For example, to get a back-slash (\) character, you’d press C, 8. (Theblank areas, for example 2, 0, indicate spaces.)

3 To enter each character, press the key combination listed on the chart.

Important: Remember, there are three ways to enter characters:Enter UsingNumbers Numeric keypadLetters/characters One-touch keysLetters/characters/numbers CODE chart for key combinations

4 Press ENTER to save the name.

0123456789ABCDEF

2 3 4 5 6 7 A B C D E F0 @ P ` p Ç É

! 1 A Q a q ü æ " 2 B R b r é Æ á β# 3 C S c s â ô í$ 4 D T d t ä ö ` ó µ% 5 E U e u à ò . ú ü& 6 F V f v å û ñ’ 7 G W g w ç ù Ñ( 8 H X h x ê ÿ \ a) 9 I Y i y ë Ö o* : J Z j z è Ü ¿+ ; K [ k { ï, < L ¥ l | î £- = M ] m } ì ¡ ÷. > N ^ n Ä «/ ? O _ o Å »

Seco

nd k

eypr

ess

First keypress

˚

¥

2.26

The list of scanner settingsItem Setting Initial setting

Document type Text, Photo/Text, Photo TextResolution 200, 300, 400, 600 dpi 200 dpiContrast Light, Little Light, Normal,

Little Dark, Dark NormalScan size Letter(SEF), Legal(SEF),

Half-letter(LEF) Letter(SEF)Reduce/Enlarge 100%, 77%(Legal→Letter),Ratio 50-200% by 1% increments 100%Auto reset time 1-10 minutes 3 minutes

On/Off *1 OffMixed original mode On/Off On

*1: It is the setting if you want to auto reset as soon as the scanning is completed.

2.27

2.28

For Printer driver

AAdd Printer Wizard . . . . . . . . . . . . . . . . . . 1.12Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.56Automatic setup current option units . . . . 1.31

CCanceling the printing job . . . . . . . . . . . . . 1.41Combine . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.27Configuration tab . . . . . . . . . . . . . . . . . . . . 1.40Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22

DDevice option tab . . . . . . . . . . . . . . . . . . . . 1.31Doc Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

EEdit custom . . . . . . . . . . . . . . . . . . . . . . . . . 1.25Error messages . . . . . . . . . . . . . . . . . . . . . . 1.49

FFit to paper . . . . . . . . . . . . . . . . . . . . . . . . . 1.21Font Manager 2000 . . . . . . . . . . . . . . . . . . 1.57

GGraphics mode . . . . . . . . . . . . . . . . . . . . . . 1.30

IInstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

from Add Printer Wizard . . . . . . . . . . . . . 1.12Installing Doc Pilot and Remote Shuttle . 1.3Plug and Play installing . . . . . . . . . . . . . . 1.9Using Setup.exe . . . . . . . . . . . . . . . . . . . . . 1.3

NNet setting tab . . . . . . . . . . . . . . . . . . . . . . 1.39Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.42

Connecting through optional network interface . . . . . . . . . . . . . . . . . . . . . . . . . . 1.43

Client/Server network . . . . . . . . . . . . . . 1.43

Peer to peer network . . . . . . . . . . . . . . . 1.43Connection through print server PC . . . 1.42Installing the software for your network environment . . . . . . . . . . . . . . . . . . . . . . . 1.46Remove the software . . . . . . . . . . . . . . . . 1.47Set TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . 1.48

OONLINE key . . . . . . . . . . . . . . . . . . . . . . . . 1.41Orientation . . . . . . . . . . . . . . . . . . . . . . . . . 1.22

PPage layout tab . . . . . . . . . . . . . . . . . . . . . . 1.27Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.23

Inch version . . . . . . . . . . . . . . . . . . . . . . . 1.23mm version . . . . . . . . . . . . . . . . . . . . . . . . 1.24

Paper destination . . . . . . . . . . . . . . . . . . . . 1.26Paper size . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22Paper source . . . . . . . . . . . . . . . . . . . . . . . . 1.25Paper tab . . . . . . . . . . . . . . . . . . . . . . 1.21, 1.35Paper type . . . . . . . . . . . . . . . . . . . . . . . . . . 1.26PCL font tab . . . . . . . . . . . . . . . . . . . . . . . . 1.37Plug and Play . . . . . . . . . . . . . . . . . . . . . . . . 1.9Print NIC status . . . . . . . . . . . . . . . . . . . . . 1.57Print PCL font list . . . . . . . . . . . . . . . . . . . 1.56Print the printer configuration page . . . . . 1.56Printer driver . . . . . . . . . . . . . . . . . . . . . . . . 1.2Printer driver settings . . . . . . . . . . . . . . . . 1.15

Open the printer properties . . . . . . . . . . 1.15From the application software . . . . . . . 1.15From the printer icon . . . . . . . . . . . . . . 1.17

Printer settings . . . . . . . . . . . . . . . . . . . . 1.19Printer monitor . . . . . . . . . . . . . . . . . . . . . . . 1.2Printer setting tab . . . . . . . . . . . . . . . . . . . 1.36

QQuality tab . . . . . . . . . . . . . . . . . . . . . . . . . 1.29

RRemote Shuttle . . . . . . . . . . . . . . . . . . 1.2, 1.32

Enlarged view . . . . . . . . . . . . . . . . . . . . . 1.33Installing . . . . . . . . . . . . . . . . . . . . . . . . . 1.32Printer setting from Remote Shuttle . . . 1.34Reduced view . . . . . . . . . . . . . . . . . . . . . . 1.33Remote Shuttle icon . . . . . . . . . . . . . . . . . 1.33

Index

2.29

Start the Remote Shuttle . . . . . . . . . . . . 1.32Remove the Doc Pilot and Remote Shuttle 1.55Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . 1.29Reverse printing . . . . . . . . . . . . . . . . . . . . . 1.26

SScale to fit . . . . . . . . . . . . . . . . . . . . . . . . . . 1.21Scaling(%) . . . . . . . . . . . . . . . . . . . . . . . . . . 1.21Software License Agreement for Network card . . . . . . . . . . . . . . . . . . . . 1.45

Software License Agreement for Printer driver . . . . . . . . . . . . . . . . . . . . . . i

Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22System requirements . . . . . . . . . . . . . . . . . . 1.1

TTest print tab . . . . . . . . . . . . . . . . . . . . . . . 1.38Toner saving . . . . . . . . . . . . . . . . . . . . . . . . 1.29True Type mode . . . . . . . . . . . . . . . . . . . . . 1.29

UUninstalling . . . . . . . . . . . . . . . . . . . . . . . . 1.55

WWatermark . . . . . . . . . . . . . . . . . . . . . . . . . 1.28

For TWAIN driver

AAccess to the Imagistics TWAIN driver . . . 2.5Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.25

CContrast . . . . . . . . . . . . . . . . . . . . . . . . 2.3, 2.20

DDocument type . . . . . . . . . . . . . . . . . . . 2.3, 2.20

EEntering characters . . . . . . . . . . . . . . 2.25-2.26Error Messages . . . . . . . . . . . . . . . . . . 2.23-2.25

II.D. Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9

Information of the Imagistics TWAIN driver 2.3Initial settings . . . . . . . . . . . . . . . . . . . . . . . 2.20

Scan parameters . . . . . . . . . . . . . . . 2.20-2.21Scanner auto reset . . . . . . . . . . . . . . . . . . 2.22

Install the TWAIN driver . . . . . . . . . . . . . . . 2.2

MMixed original mode . . . . . . . . . . . . . . . . . . 2.20

RReal-time scanning mode . . . . . . . . . . . . . . . 2.3Reduce/Enlarge . . . . . . . . . . . . . . . . . . . . . . . 2.4Resolution . . . . . . . . . . . . . . . . . . . . . . . 2.4, 2.20

SScan boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8Scan size . . . . . . . . . . . . . . . . . . . . . . . . 2.3, 2.20Scan-box mode . . . . . . . . . . . . . . . . . . . . . . . 2.3

Erasing a document stored in a scan box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.13-2.14Erasing a scan box . . . . . . . . . . . . . . 2.15-2.16Preview . . . . . . . . . . . . . . . . . . . . . . . 2.18-2.20Refresh . . . . . . . . . . . . . . . . . . . . . . . 2.18-2.20Retrieving an image . . . . . . . . . . . . . . . . . 2.17Scan-box mode . . . . . . . . . . . . . . . . . . 2.9-2.10Scanning the image . . . . . . . . . . . . . 2.11-2.12

Scanner settings list . . . . . . . . . . . . . . . . . . 2.22Scanning the image . . . . . . . . . . . . . . . . . . . 2.5

Using the Real time Scanning mode . 2.6-2.7Using the Scan Box mode . . . . . . . . . 2.8-2.19

System requirements . . . . . . . . . . . . . . . . . . 2.1

UUninstall the TWAIN driver . . . . . . . . . . . . 2.2

D76-9A070-60

Printer Controller User's Guide

Documents

Printer Driver Manual - files.oceusa.comfiles.oceusa.com/media/Assets/PDFs/TSS/external/ix3010/... · The Imagistics Printer driver CD contains the printer driver and TWAIN driver