PRIMERGY BX900/BX400 Blade Server Systems - Fujitsumanuals.ts.fujitsu.com/file/10227/sb6-sb11a-sb11-smg-en.pdf · PY CB Eth Switch/IBP 1 GB 18/6 ... 4.1.2 System Utilities ... 356

System Message Guide

PRIMERGY BX900/BX400 Blade Server Systems Ethernet Connection Blade Module SB6 / SB11a / SB11 Switch and IBP VersionEnglish

PRIMERGY BX400/BX900 Connection Blades

Ethernet Connection Blades

PY CB Eth Switch/IBP 1 GB 18/6 (SB6) PY CB Eth Switch/IBP 1 GB 36/12 (SB11a) PY CB Eth Switch/IBP 1 GB 36/8+2 (SB11)

System Message Guide Switch and IBP version

Edition Jan 2012

© 2011 Fujitsu Technology Solutions

Comments… Suggestions… Corrections…

The User documentation Department would like to know your opinion on this manual. Your feedback helps us to optimize our documentation to suit your individual needs.

Fax forms for sending us your comments are included at the back of the manual. There you will also find the addresses of the relevant User documentation Department.

Copyright and Trademarks

Copyright © 2011 Fujitsu Technology Solutions GmbH.

All rights reserved.

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers


Content

1 System Message Overview ...................................................................................... 7 1.1 How to Read System Messages ................................................................................. 8 1.2 Error Message Traceback Reports ........................................................................... 10

2 Message and Recovery Procedures ..................................................................... 11 2.1 System Messages .................................................................................................... 13 2.2 Event Message......................................................................................................... 25 2.3 File System Messages ............................................................................................. 26 2.4 User Configuration Messages .................................................................................. 28 2.5 CLI Messages .......................................................................................................... 29 2.6 Web Messages......................................................................................................... 31 2.7 ACL Messages ......................................................................................................... 32 2.8 DiffServ Messages ................................................................................................... 33 2.9 COS Messages ........................................................................................................ 44 2.10 DOT1X Messages .................................................................................................... 52 2.11 RADIUS Messages .................................................................................................. 59 2.12 TACACS Messages ................................................................................................. 67 2.13 BOOTP Client Messages ......................................................................................... 68 2.14 DHCP Client Messages ............................................................................................ 70 2.15 DHCP Relay Messages ............................................................................................ 73 2.16 DNS Relay Messages .............................................................................................. 76 2.17 DDNS Client ............................................................................................................. 77 2.18 sFlow Messages ....................................................................................................... 77 2.19 IGMP Snooping System Messages .......................................................................... 79 2.20 SNTP Messages ...................................................................................................... 82 2.21 VLAN Messages ....................................................................................................... 84 2.22 SPAN TREE Messages ............................................................................................ 86 2.23 STORM CONTROL Messages ................................................................................. 90 2.24 Port-Monitor Messages ............................................................................................ 96 2.25 SNMP Messages ...................................................................................................... 97 2.26 PING & TRACEROUTE Utility Messages ................................................................. 99 2.27 TFTP/FTP Messages ............................................................................................. 101 2.28 Timer Messages ..................................................................................................... 105 2.29 Stacking Messages ................................................................................................ 106 2.30 ISMIC Messages .................................................................................................... 113 2.31 Port Group Messages............................................................................................. 114 2.32 Uplink Set Messages .............................................................................................. 115 2.33 VLAN Port Group Messages .................................................................................. 116 2.34 Link State Messages .............................................................................................. 118 2.35 Port Backup Messages ........................................................................................... 119 2.36 SFlow Messages .................................................................................................... 120 2.37 Err-Disable Recovery ............................................................................................. 128 2.38 MAC Bucket Overflow ............................................................................................ 128 2.39 Pin Group ............................................................................................................... 129

3 CLI Error Messages .............................................................................................. 130 3.1 Management .......................................................................................................... 130 3.1.1 Configuration .......................................................................................................... 130 3.1.2 System Utilities ....................................................................................................... 149 3.1.3 File Management .................................................................................................... 153 3.1.4 User Manangement ................................................................................................ 156 3.1.5 Privilege Level ........................................................................................................ 161


3.1.6 Logging .................................................................................................................. 163 3.1.7 SNMP ..................................................................................................................... 165 3.1.8 SNTP ..................................................................................................................... 168 3.1.9 CDP ....................................................................................................................... 171 3.1.10 UDLD ..................................................................................................................... 172 3.1.11 LLDP ...................................................................................................................... 174 3.1.12 DHCP ..................................................................................................................... 177 3.1.13 DNS Relay ............................................................................................................. 179 3.1.14 sFlow ...................................................................................................................... 181 3.2 Switching ................................................................................................................ 183 3.2.1 Forwarding Database ............................................................................................. 183 3.2.2 Port ........................................................................................................................ 184 3.2.3 VLAN ...................................................................................................................... 188 3.2.4 Protocol-based VLAN ............................................................................................. 192 3.2.5 IP Subnet-based VLAN .......................................................................................... 194 3.2.6 MAC-based VLAN .................................................................................................. 196 3.2.7 GARP ..................................................................................................................... 197 3.2.8 VTP ........................................................................................................................ 199 3.2.9 IGMP Snooping ...................................................................................................... 201 3.2.10 MLD Snooping........................................................................................................ 206 3.2.11 Multicast Forwarding Database .............................................................................. 210 3.2.12 Port-Channel .......................................................................................................... 211 3.2.13 Spanning-Tree........................................................................................................ 214 3.2.14 Link-State ............................................................................................................... 220 3.2.15 Port-backup ............................................................................................................ 223 3.2.16 MAC Filter .............................................................................................................. 225 3.3 Group Administration (IBP) ..................................................................................... 227 3.3.1 Uplink Set ............................................................................................................... 227 3.3.2 Port-Group ............................................................................................................. 229 3.3.3 VLAN Port-Group ................................................................................................... 231 3.3.4 Service LAN ........................................................................................................... 233 3.3.5 Service VLAN ......................................................................................................... 235 3.3.6 Lock ....................................................................................................................... 237 3.3.7 Port ........................................................................................................................ 239 3.3.8 IGMP Snooping ...................................................................................................... 243 3.3.9 Port-Channel .......................................................................................................... 244 3.3.10 Link-State ............................................................................................................... 248 3.3.11 Port-backup ............................................................................................................ 249 3.4 Security .................................................................................................................. 250 3.4.1 Port Access Control ................................................................................................ 250 3.4.2 Port Security ........................................................................................................... 254 3.4.3 RADIUS.................................................................................................................. 257 3.4.4 TACACS+ .............................................................................................................. 261 3.4.5 LDAP ...................................................................................................................... 263 3.4.6 Access Control Lists ............................................................................................... 264 3.4.7 IP Filter ................................................................................................................... 271 3.4.8 Secure HTTP ......................................................................................................... 272 3.4.9 Secure Shell ........................................................................................................... 273 3.4.10 Denial-of-Service .................................................................................................... 274 3.5 QoS ........................................................................................................................ 275 3.5.1 DiffServ .................................................................................................................. 275 3.5.2 COS Messages ...................................................................................................... 287 3.6 Stacking ................................................................................................................. 291 3.7 End-Host-Mode ...................................................................................................... 294

4 Web Error Messages ............................................................................................ 295 4.1 Management .......................................................................................................... 295 4.1.1 Configuration .......................................................................................................... 295


4.1.2 System Utilities ....................................................................................................... 304 4.1.3 File Management .................................................................................................... 307 4.1.4 User Manangement ................................................................................................ 310 4.1.5 Logging .................................................................................................................. 315 4.1.6 SNMP ..................................................................................................................... 317 4.1.7 SNTP ..................................................................................................................... 323 4.1.8 UDLD ..................................................................................................................... 328 4.1.9 CDP ....................................................................................................................... 329 4.1.10 LLDP ...................................................................................................................... 330 4.1.11 DHCP ..................................................................................................................... 331 4.1.12 DNS Relay ............................................................................................................. 332 4.1.13 sFlow ...................................................................................................................... 336 4.2 Switching ................................................................................................................ 339 4.2.1 Forwarding Database ............................................................................................. 339 4.2.2 Port ........................................................................................................................ 340 4.2.3 VLAN ...................................................................................................................... 344 4.2.4 Protocol-based VLAN ............................................................................................. 345 4.2.5 IP Subnet-based VLAN .......................................................................................... 346 4.2.6 MAC-based VLAN .................................................................................................. 348 4.2.7 GARP ..................................................................................................................... 349 4.2.8 VTP ........................................................................................................................ 350 4.2.9 IGMP Snooping ...................................................................................................... 351 4.2.10 MLD Snooping........................................................................................................ 356 4.2.11 Multicast Forwarding Database .............................................................................. 361 4.2.12 Port-Channel .......................................................................................................... 362 4.2.13 Spanning-Tree........................................................................................................ 365 4.2.14 Link-State ............................................................................................................... 371 4.2.15 Port-backup ............................................................................................................ 372 4.2.16 MAC Filter .............................................................................................................. 373 4.3 Group Administration (IBP) ..................................................................................... 374 4.3.1 Uplink-Set ............................................................................................................... 374 4.3.2 Port-Group ............................................................................................................. 376 4.3.3 VLAN Port-Group ................................................................................................... 377 4.3.4 Service LAN ........................................................................................................... 379 4.3.5 Service VLAN ......................................................................................................... 381 4.3.6 Port ........................................................................................................................ 383 4.3.7 Port-Channel .......................................................................................................... 385 4.3.8 Link-State ............................................................................................................... 389 4.3.9 Port-backup ............................................................................................................ 390 4.4 Security .................................................................................................................. 391 4.4.1 Port Access Control ................................................................................................ 391 4.4.2 Port Security ........................................................................................................... 393 4.4.3 RADIUS.................................................................................................................. 395 4.4.4 TACACS+ .............................................................................................................. 398 4.4.5 LDAP ...................................................................................................................... 400 4.4.6 Access Control Lists ............................................................................................... 401 4.4.7 IP Filter ................................................................................................................... 410 4.4.8 Secure HTTP ......................................................................................................... 412 4.4.9 Secure Shell ........................................................................................................... 414 4.4.10 Denial-of-Service .................................................................................................... 415 4.5 QoS ........................................................................................................................ 416 4.5.1 DiffServ .................................................................................................................. 416 4.5.2 COS Messages ...................................................................................................... 423 4.6 Stacking ................................................................................................................. 424 4.7 End-Host-Mode ...................................................................................................... 427


Revision History

Revision Date Editor Remark 0.1 1/5/2009 Moore C. J. Lee 1st Draft 0.2 6/1/2009 Moore C. J. Lee

EIT Team Add CLI and Web error messages

0.3 6/26/2009 Moore C. J. Lee switch version 0.4 1/21/2011 Moore C. J. Lee New messages for stacking 0.5 7/29/2011 Moore C. J. Lee New messages for EHM

Storm control and errdisable recovery MAC bucket overflow

0.6 9/29/2011 Moore C. J. Lee Update EHM messages 0.65 01/19/2012 E.Schröer Merged SB6/SB11/SB11a –

Switch/IBP


1 System Message Overview This guide describes the PRIMERGY BX900 Ethernet Connection Blade specific system messages that you might encounter. Basically, the guide does not describe how to install your connection blade or how to configure software features on your switch. It also provide detailed information about commands that have been created or changed for use by the connection blade.

During operation, the system software sends these messages to the console (and, optionally, to a logging server on another system). Not all system messages indicate problems with your system. Some messages are purely informational, whereas others can help diagnose problems with communications lines, internal hardware, or the system software. This guide also includes error messages that appear when the system fails.

This chapter contains these sections:

− How to Read System Messages

− Error Message Traceback Reports


1.1 How to Read System Messages

System log messages can contain up to 80 characters and a percent sign (%), which follows the optional sequence number or time stamp information, if configured. Messages are displayed in this format:

<2> MAR 29 10:02:53 0.0.0.0-1 UNKN[268434944]: bootos.c(520) 1 %% Event(0xaaaaaa

aa)

<6> MAR 29 10:02:54 0.0.0.0-1 UNKN[268434944]: bootos.c(575) 2 %% Starting code.

..

<6> MAR 29 10:03:17 0.0.0.0-1 UNKN[218404976]: edb.c(360) 3 %% EDB Callback: Unit Join: 1.

By default, a switch sends the output from system messages to a logging process. In a switch stack, stack members append their hostnames to the output from system messages and redirect the output to the logging process on the stack master.

Each system message begins with a percent sign (%) and is structured as follows:

%FACILITY-SEVERITY-MNEMONIC: Message-text

• FACILITY is a code consisting of two or more upper case letters that show the facility to which the message refers. A facility can be a hardware device, a protocol, or a module of the system software. Table 1-1 lists the switch system specific facility codes.

The messages are described in Chapter 2, “Message and Recovery Procedures”, in alphabetical order by facility code, with the most severe (lowest number) errors described first.

Facility Code Description ACL Access Control List BOOTP Bootp Client CLI Command Line Interface COS Class of Service (802.1p) DHCP DHCP Client DNS DNS Relay & Client System DDNS Dyamic DNS Client DiffServ Policy Base QoS DiffServ System Dot1X 802.1X Security System Event Event System Log Messages File System Config File System IGMP Snooping IGMP Snooping & Query System Port-Monitor Port Monitor System Ping Ping & Traceroute Utility RADIUS Radius Client Security System System System Configuration & Event Description SNMP SNMP v1/v2/v3 & RMON System


SNTP SNTP Timer Client System Spanning Tree 802.1D/W/S Spanning Tree Control Storm Control Storm Control System Stacking Stacking System TACACS TACACS+ Security System TFTP TFTP/FTP Upgrade System Timer System timer Clock VLAN 802.1Q GVRP/GARP/GMRP User Configuration User Login & Admin Control Web Web UI System

Table 1-1 Facility code list

• SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower the number, the more serious the situation. Table 1-2 lists the message severity levels.

Severity Level Description 0 – emergency System is unusable. 1 – alert Immediate action required. 2 – critical Critical condition. 3 – error Error condition. 4 – warning Warning condition. 5 – notification Normal but significant condition. 6 – informationalInformational message only. 7 – debugging Message that appears during debugging only.

Table 1-2 Message Severity Levels

All syslog messages generated by a PRIMERGY BX900 switch other than the master switch are displayed ending with (Switch-x) where Switch is the ip address of stack master and x is the unit number of the stack member generating the message.

This example shows a partial switch system message on a switch other than a PRIMERGY BX900 Connection Blade:

0 2000/04/01 09:41:21 Link Up: Unit: 1 Slot: 0 Port: 8

1 2000/04/01 06:34:02 Link Down: Unit: 1 Slot: 0 Port: 8

2 2000/04/01 01:57:25 Link Up: Unit: 1 Slot: 0 Port: 8

3 2000/04/01 01:57:24 Link Down: Unit: 1 Slot: 0 Port: 8


1.2 Error Message Traceback Reports

Some messages describe internal errors and contain traceback information. This information is very important and should be included when you report a problem to your technical support representative.

This message example includes traceback information:

− Process=”Exec”, level=0, pid=17

− Traceback=1A82 1AB4 6378 A072 1054 1860

Some System messages ask you to copy the error messages and take further action. These online tools also provide more information about system error messages.


2 Message and Recovery Procedures This chapter describes the PRIMERGY BX900 switch system messages in alphabetical order by facility. Within each facility, the messages are listed by severity levels 0 to 7: 0 is the highest severity level and 7 is the lowest severity level. Each message is followed by an explanation and a recommended action.

The messages listed in this chapter do not include the hostname or the date/time stamp designation that display only if the software is configured for system log messaging.

The chapter includes these message facilities:

• System Messages

• Event Messages

• VLAN Messages

• Spanning Tree Messages

• Storm Control Messages

• Port-Monitor Messages

• IGMP Snooping Messages

• BOOTP Client Messages

• DHCP Client Messages

• DNS Relay Messages

• DDNS Client Messages

• TACACS+ Messages

• DOT1X Messages

• RADIUS Messages

• COS Messages

• ACL Messages

• DiffServ Messages

• Stacking Messages

• File System messages

• PING & TRACEROUTE Utility Messages

• SNTP Messages

• TFTP/FTP Messages

• User Configuration Messages

• SNMP Messages

• CLI Messages

• Web Messages

• sFlow Messages



2.1 System Messages

This section contains system module messages.

Severity Level 2 Error Message 0xaaaaaaaa Explanation Start of new execution Recommended Action The system starts to init.

Severity Level 2 Error Message 0xbbbbbbbb Explanation The auto-download process is finished and the switch is going to

be rebooted. Recommended Action After the switch is booted, checking if it is joined to the stack and

the version of the switch is upgraded.

Severity Level 2 Error Message 0xcccccccc Explanation The event log is cleared. Recommended Action The event log is cleared. There should be one entry in the event

log.

Severity Level 2 Error Message 0xdddddddd Explanation Single-bit ECC error is detected. Recommended Action If it is possible, user is recommended to replace the DDR-RAM

module from the blade switch.

Severity Level 2 Error Message 0x4 Explanation This event is logged while a user try to reload a stack, stack

master and stack members will log this event. Recommended Action Please check if the stack had ever issued a reload command.

Severity Level 2 Error Message 0x0 Explanation This event is logged while a user try to reload a stack member,

stack member will log this event. Recommended Action Please check if the stack master had ever issued a reload

command to this stack member.


Severity Level 2 Error Message OS_TYPE Explanation OS type register fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message logWriteInMemoryLogToFile: osapiFsCreateFile failed Explanation Log file creation is failed on RAMDISK. Recommended Action The system is failed to init.

Severity Level 6 Error Message logWriteInMemoryLogToFile: osapiFsDeleteFile failed Explanation Log file deletion is failed on RAMDISK Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiFsClose failed Explanation Log file close is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiFsDeleteFile failed Explanation Log file deletion is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiMsgQueueCreate: msgQCreate Failed Explanation Message queue create fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiMessageSend called with wait time < -1 Explanation Message queue send fail (wait time < 0). Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiMessageReceive called with wait time < -1 Explanation Message queue receive fail (wait time < 0). Recommended Action The system is failed to init.


Severity Level 6 Error Message Error: SIM – could not add management MAC. Explanation Fail to add the MAC address of systems CPU to table. Recommended Action The system MAC address table is abnormal.

Severity Level 6 Error Message Error on call to sysapiRegistryGet routine with key SYS_MAC Explanation System registry get fail Recommended Action The system is failed to init.

Severity Level 6 Error Message Error on call to sysapiCfgFileWrite routine on config file

simCfgData.cfg Explanation Get system registry fail. Recommended Action The config file is corrupt instead of the factory default


simCfgData.cfg Explanation Get system registry fail. Recommended Action The config file is corrupt instead of the factory default

Severity Level 6 Error Message Failed to Create Transfer Task. Explanation Task creation is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message Error on call to sysapiRegistryGet routine with key SYS_MAC Explanation System registry get fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message simCnfgrInitPhase1Process: Error could not create ip stats Explanation Fail to create the ip counters. Recommended Action The system is failed to init.

Severity Level 6 Error Message SIM: Unable to register for interface state change callback. Explanation Callback function registration is failed. Recommended Action The system is failed to init.


Severity Level 6 Error Message sysapiPrintfMsgQueueTask: Failed to create queue, exiting… Explanation Message queue create is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiMsgQueueGetNumMsgs failed Explanation Message queue count get fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message sysapiPrintfMsgEnqueue: Failed to send … Explanation Message send fail Recommended Action The system is failed to init.

Severity Level 6 Error Message sysapiPrintfMsgEnqueue: sysapiPrintfMsgQueueTask Not

Ready Explanation Message send fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message sysapiRegistryGet failed Explanation System registry get fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message sysapiRegistryPut failed. Explanation System registry put fail. Recommended Action The system is failed to init.

Severity Level 6 Error Message osapiMalloc() failed Explanation Memory allocate fail. Recommended Action The system is crashed.


Severity Level 6 Error Message Failed to malloc pSysapiCfgTree[INDEX] Explanation Memory allocation is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message Could not separate SYSAPI_CONFIG_FILENAME Explanation Configuration file separation is failed. Recommended Action The configuration file is wrong and need to check again.

Severity Level 6 Error Message Configuration file FILENAME size is 0 (zero) bytes. Explanation Getting configuration file size is failed. Recommended Action The configuration file corrupts or does not exists instead of the

factory default.

Severity Level 6 Error Message Failed to read config file FILENAME header Explanation Configuration file read fail. Recommended Action The config file is corrupted instead of the factory default.

Severity Level 6 Error Message Version Check Failed. Explanation Wrong configuration file version. Recommended Action The configuration file needs to be verified.

Severity Level 6 Error Message Configuration file on disk size SIZE1 is less than expected size

SIZE2. Explanation Wrong configuration file size. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message sysapiCfgFilesSeparate: CRC check failed. CHECKSUM1 read

and CHECKSUM2 calculated. Explanation Wrong configuration file checksum value. Recommended Action The configuration file is not matched and need to be checked.

Severity Level 6 Error Message File FILENAME1 hdr name = FILENAME2 is invalid. Explanation Wrong configuration file name. Recommended Action The configuration file name is wrong and need to be checked.


Severity Level 6 Error Message Failed to allocate SIZE for config file FILENAME Explanation Memory allocate fail. Recommended Action The configure file is corrupted instead of the factory default.

Severity Level 6 Error Message File FILENAME: same version (VERSION1) but the sizes

(SIZE1->SIZE2) differ. Explanation Wrong configuration file size. Recommended Action The configuration file is not matched and need to be checked.

Severity Level 6 Error Message File FILENAME corrupted from file system. Checksum

mismatch. Explanation Wrong configuration file checksum value. Recommended Action The configuration file is not matched and need to be checked.

Severity Level 6 Error Message Error on call to sysapiCfgFileWrite routine on file FILENAME. Explanation Configuration file write fail. Recommended Action The configuration file is not matched and need to be checked.

Severity Level 6 Error Message pSysapiCfgTree[INDEX] is NULL Explanation Configuration file index gets fail. Recommended Action The configuration file is not matched and need to be checked.

Severity Level 6 Error Message Out of system buffers. Explanation Netowk mbuf gets fail. Recommended Action The system is still crashed.

Severity Level 6 Error Message nvStore registrar_ID greater than NVSTORE_USER_LAST. Explanation Component save routine registers fail. Recommended Action System is abnormal and suggests to reboot the system.


Severity Level 6 Error Message nvStore registrar_ID already registered. Explanation Component save routine registers fail. Recommended Action System is abnormal and suggests to reboot the system.

Severity Level 6 Error Message nvStore registrar_ID not registered. Explanation Component save routine deregisters fail. Recommended Action System is abnormal and suggests to reboot the system.

Severity Level 6 Error Message Error on call to sysapiRegistryGet routine with key

BULK_STORAGE_TYPE. Explanation Registry gets fail. Recommended Action The configuration file is corrupt instead of the factory default.

Severity Level 6 Error Message sysapiEnableWriteToFlash failed Explanation Flash write enable/disable failed. Recommended Action The restore process was failed and need to check the

configuration file is available.

Severity Level 6 Error Message Bad rc on Save call to registrar_ID Explanation Bad return value on notify save configuration call. Recommended Action The configuration file might be corrupted instead of the factory

default.

Severity Level 6 Error Message About to restore defaults for component id ID at time TIME. Explanation Call all components factory defaults restore routine. Recommended Action The configuration file might be corrupted instead of the factory

default.

Severity Level 6 Error Message Bad rc on Restore call to registrar_ID ID TIME Explanation Bad return value on notify restore call. Recommended Action The restore process was failed and need to check the

configuration file is available.


Severity Level 6 Error Message Bad rc on config dump call to registrar_ID ID Explanation Bad return value on notify configure dump call. Recommended Action The restore process was failed and need to check the

configuration file availability.

Severity Level 6 Error Message Bad rc on debug dump call to registrar_ID ID Explanation Bad return value on notify debug dump call. Recommended Action The restore process was failed and need to check the availability

of the configuration file.

Severity Level 6 Error Message Error on call to osapiFsWrite routine on file FILE Explanation Configuration file writes fail. Recommended Action The configuration file is corrupted instead of the factory_default.

Severity Level 6 Error Message File FILE corrupted from file system. Checksum mismatch. Explanation Configuration file checksum error. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message Migrating config file FILE from version NUMBER1 to NUMBER2.Explanation Configuration file migration is failed. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message Failed to get sizeof Config file FILENAME. Explanation Wrong file size. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message sysapiCfgFileIndexGet (FILENAME) failed. Explanation Wrong file index. Recommended Action The configuration file is corrupted instead of the factory default.


Severity Level 6 Error Message osapiMalloc (SIZE) failed. Explanation Memory allocation is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message Failed to read config file FILENAME data SIZE Explanation Fail to converts uncombined configuration files to combined

configuration files. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message sysapiCfgFileMapInterfaces failed. Explanation Fail to create mapping for interfaces from current release to

subsequence release. Recommended Action The system is failed to init.

Severity Level 6 Error Message cfgFileCount > SYSAPI_MAX_FILE_ENTRIES Explanation Configuration file too much. Recommended Action The system configuration file exceed to the system limitation.

Severity Level 6 Error Message sysapiCfgFileIndexGet (FILENAME) failed. Explanation Configuration file index gets fail. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message Invalid index INDEX MAX = MAXINDEX Explanation Configuration file index gets fail. Recommended Action The configuration file is corrupted instead of the factory default.

Severity Level 6 Error Message Invalid slot SLOT or port PORT Explanation Invalid slot or port value Recommended Action The configuration file is corrupted instead of the factory default.


Severity Level 6 Error Message Map index INDEX is out of range Explanation Invalid index value. Recommended Action The system configuration is error.

Severity Level 6 Error Message File FILENAME not found. Explanation Cannot find file. Recommended Action The configuration file is wrong and need to be checked.

Severity Level 6 Error Message sysapiCfgFileRel4_0Separate: Allocating BUFFERSIZE Explanation Function sysapiCfgFileRel4_0Separate result. Recommended Action The system configuration is error.

Severity Level 6 Error Message Malloc SIZE Failed Explanation Memory allocate fail. Recommended Action The system is crashed.

Severity Level 6 Error Message CRC check failed. CHECKSUM1 read and CHECKSUM2

calculated. Explanation Invalid checksum value. Recommended Action The configuration file is wrong and need to be checked.

Severity Level 6 Error Message Config FILENAME is separated from FILENAME length =

LENGTH Explanation Unconbined configuration file is separated. Recommended Action The configuration file is wrong and need to be checked.

Severity Level 6 Error Message sysapiCfgFileRel4_0CfgEntryAdd(FILENAME) Failed. Explanation Read configuration from buffer and fill the configuration tree fail. Recommended Action The configuration file is wrong and need to be checked.


Severity Level 6 Error Message Config FILENAME is not separated from FILENAME as we don’t

need. Explanation Unconbined configuration file is failed to separate. Recommended Action The configuration file is wrong and need to be checked.

Severity Level 6 Error Message WDT Function init OK. Explanation The watch dog timer is initialized successfully. Recommended Action Watch dog timer is started by system.

Severity Level 6 Error Message ECC Error Detect Function init OK. Explanation The ECC error detect task is initialized successfully. Recommended Action The ECC error detect task is started by system.

Severity Level 6 Error Message ECC Error Detect Function init FAIL. Explanation The initialization of ECC error detect task is failed. Recommended Action Reboot the switch again.

Severity Level 6 Error Message Single-bit ECC error (0x%08x), interrupt counter = %d, capture

addr = 0x%08x Explanation A single-bit ECC error is detected on <addr>. Recommended Action There is a single-bit ECC error is detected. If it is possible, user

is recommended to replace the DDR-RAM module from switch.

Severity Level 6 Error Message Link Up: Unit: <unitId> Slot: <slotId> Port: <portNo> Explanation The interface unit/slot/port is link up. Recommended Action

Severity Level 6 Error Message Link Down: Unit: <unitId> Slot: <slotId> Port: <portNo> Explanation The interface unit/slot/port is link down. Recommended Action


Severity Level 2 Error Message 0x17171717 Explanation This unit is reset due to the lost of the master election Recommended Action All the units attached to this stack master will be reset to join the

stack again.


2.2 Event Message

This section contains Event module messages.

Severity Level 6 Error Message Unable to initialize async event handler utility. Explanation Event handler resource initialization failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message Failed to create event handler for component id ID. Explanation Event handler creation is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message Unable to delete event handler rwlock for component async

handler ID. Explanation Event handler deletion is failed. Recommended Action The system is failed to init.

Severity Level 6 Error Message Entry not in use. Explanation Event handler not in use when delete it. Recommended Action The event handler is failed.

Severity Level 6 Error Message Failed to create correlator for handler id ID and component ID. Explanation Correlator creation is failed. Recommended Action The handler is failed to create.

Severity Level 6 Error Message Handler: ID Correlator: ID : Attempting to delete a correlator

which is not in use. Explanation Correlator deletion is failed. Recommended Action The handler is failed to delete.


2.3 File System Messages

This section contains the File system module messages.

Severity Level 6 Error Message ftruncate failed ?File resides on a read-only file system. Explanation File write fail. Recommended Action The file is read-only.

Severity Level 6 Error Message ftruncate failed ?File is open for reading only. Explanation File write fail. Recommended Action The file is read-only.

Severity Level 6 Error Message ftruncate failed ?File descriptor refers to a file on which this

operation is impossible. Explanation File write fail. Recommended Action The file is read-only.

Severity Level 6 Error Message ftruncate failed ?Return an unknown code in errno. Explanation File write fail. Recommended Action The file is read-only.

Severity Level 6 Error Message File “FILENAMe” delete failed. Explanation Delete file result message. Recommended Action The file is failed to delete.

Severity Level 6 Error Message BootROM file “FILENAME” start up failed. Explanation Start up BootROM file result message. Recommended Action The file is failed to startup.


Severity Level 6 Error Message Operation code file “FILENAME” start up failed. Explanation Start up operation code file result message. Recommended Action The startup operation is failed.

Severity Level 6 Error Message Configuration file “FILENAME” start up failed. Explanation Start up configuration file result message. Recommended Action The configuration file is failed to set to startup configuration.


2.4 User Configuration Messages

This section contains the User Configuration module messages.

Severity Level 2 Error Message Registrar ID Explanation Bad return value on notify save call. Recommended Action The system is not init successful.

Severity Level 6 Error Message Error on call to osapiFsWrite routine on config file user_mgr.cfg Explanation Configuration file write fails. Recommended Action The configuration is corrupted instead of the factory default.

Severity Level 6 Error Message User Login Failed for USERNAME Explanation User authentication is failed. Recommended Action Check the username and password is correct or not.

Severity Level 6 Error Message Access level for user USERNAME could not be determined.

Setting to READ_ONLY. Explanation User authority issue. Recommended Action Check the user authority.

Severity Level 6 Error Message Could not migrate config file user_mgr.cfg from version

NUMBER1 to NUMBER2. Using defaults. Explanation Configuration data migration fails. Recommended Action The configuration file is corrupted instead of the factory default.


2.5 CLI Messages

This section contains the CLI module messages.

Severity Level 6 Error Message Invalid USER access level detected at cliSecurityLevelCheck. Explanation Invalid USER access level detected Recommended Action Invalid user to acces into the system

Severity Level 6 Error Message Invalid access level detected at cliSecurityLevelCheck. Explanation Invalid access level detected Recommended Action Invalid user to acces into the system

Severity Level 6 Error Message Telnet Send Failed errno = 0xXX Explanation Telnet write text string to client Recommended Action The telent function is invalid.

Severity Level 6 Error Message not able to open the file specified Explanation check for file opening Recommended Action The file is failed to open.

Severity Level 6 Error Message not able to closed the file specified Explanation check for file closing Recommended Action The file is falied to closed

Severity Level 6 Error Message File size is zero or file do not exists Explanation Get the size of the file Recommended Action The file is not existed

Severity Level 6 Error Message Not able to read the file Explanation read the contents of file in a temporary array Recommended Action The file is not readable.


Severity Level 6 Error Message Error on call to osapiFsWrite routine on config file

cliWebCfgData.cfg Explanation call save NVStore routine Recommended Action The file is faliled to save.

Severity Level 6 Error Message __FILE__ : cliWebPhaseOneInit: __LINE__: Failed to allocate

memory for cliCommon. Explanation Failed to allocate memory Recommended Action The System is failed for the memory allocated.

Severity Level 6 Error Message Failed registration for TRAPMGR CARD EVENTS Explanation register with TRAPMGR to receive card trap notifications Recommended Action The TRAP EVENY is occurred.

Severity Level 6 Error Message osapiFsDir failed Explanation Get the directory listing Recommended Action The Directory is Failed to get the directory.

Severity Level 6 Error Message Login Session semaphore not created. Explanation Login Session semaphore not created. Recommended Action Login session is not syschonous

Severity Level 6 Error Message Login Session logout index out of bounds (sessionIndex) Explanation Check Login Session logout index Recommended Action The Login users are full of the system


2.6 Web Messages

This section contains the WEB module messages.

Severity Level 6 Error Message Failed to create the Java Socket Explanation Failed to create the Java socket. Recommended Action The web system is failed to init.

Severity Level 6 Error Message Failed to bind to the Java port Explanation Failed to bind to the Java port. Recommended Action The web system is failed to init.

Severity Level 6 Error Message Listen failure on the Java port Explanation Listen failure on the Java port Recommended Action The web system is failed to init.

Severity Level 6 Error Message Error on select. Explanation Error on select. Recommended Action The web system needs to check the network environment.

Severity Level 6 Error Message Max clients exceeded. Explanation Max clients exceeded. Recommended Action The web system is full loading.

Severity Level 6 Error Message Invalid recv datalength Explanation Invalid receive data length. Recommended Action The network environment is abnormal.

Severity Level 6 Error Message Error on send to sockfd <sockfd>, closing connection Explanation Error on send to socket, closing connection. Recommended Action The network environment is abnormal.


2.7 ACL Messages

This section contains ACL module messages.

Severity Level 6 Error Message Total number of ACL rules (%u) exceeds max (%u) on intf %u

%s. Applying deny all rule to device Explanation Total number of ACL rules exceeds ACL rules on interface Recommended Action Reduce other system activity to ease some rules demands.

Severity Level 6 Error Message Removed %s ACL %u from intf %u %s, but unable to apply

remaining ACLs to device Explanation Unable to remove ACL from device. Recommended Action Reduce other system activity to ease demands.


2.8 DiffServ Messages

This section contains DiffServ module messages.

Severity Level 6 Error Message No DiffServ policy applied on port <bcmx_lport> Explanation No DiffServ policy applied on port Recommended Action The port nimber is not matched the Diffserv poicy.

Severity Level 6 Error Message DiffServ not removed from port <bcmx_lport> Explanation DiffServ not removed from port Recommended Action The port nimber is not matched the Diffserv poicy.

Severity Level 6 Error Message routine_name: Error activating saved config for intIfNum

<intIfNum> -- using factory defaults instead Explanation Error activating saved config Recommended Action The Diffserv Config file is corrupt.

Severity Level 6 Error Message routine_name: Error activating saved config for intIfNum

<intIfNum> -- attempt to use factory defaults also failed Explanation Error activating saved config Recommended Action The Diffserv Config file is corrupt.

Severity Level 6 Error Message routine_name: Error deleting service interface <intIfNum>

<Direction> Explanation Error deleting service interface Recommended Action The interface port is not matched the diffserv service

Severity Level 6 Error Message routine_name: Error during callback processing for intf

<intIfNum> , event <event> Explanation Error during callback processing Recommended Action The system is failed to init to the Diffserv Service.


Severity Level 6 Error Message Error accessing DIFFSERV config data for interface <intIfNum>

in diffServMapIntfIsConfigurable. Explanation Error accessing DIFFSERV config data for interface Recommended Action Access the config data error to set.

Severity Level 6 Error Message diffServClassRuleCreate: Error deleting row after create failure

for indexes <classIndex>, <classRuleIndex> Explanation Error deleting row after create failure Recommended Action Error to delete the config data

Severity Level 6 Error Message diffServClassRuleDelete: couldn't delete row AVL node for rule

<classRuleIndex> in class <className> Explanation couldn't delete row AVL node for rule Recommended Action Error to delete the config data and rule.

Severity Level 6 Error Message diffServClassRuleObjectSet: attempt to destroy the row failed Explanation attempt to destroy the row failed Recommended Action Error to delete the config data and rule.

Severity Level 6 Error Message dsmibClassRuleIndexNextUpdate: ERROR -- could not find

class row for index <classIndex> Explanation could not find class row for index Recommended Action To search the class data not match the config

Severity Level 6 Error Message dsmibClassRuleIndexNextUndo: ERROR -- could not find class

row for index <classIndex> Explanation could not find class row for index Recommended Action To search the class data not match the config

Severity Level 6 Error Message dsmibClassRuleIndexNextUndo: WARNING -- attempting to

decrement an indexNext value of <index> for class <classIndex>Explanation attempting to decrement an indexNext value Recommended Action The Class Rule will be full not to add more


Severity Level 6 Error Message dsmibClassRuleAclDelete: Could not delete rule

<classRuleIndex> from class <name> Explanation Could not delete rule Recommended Action Failed to delete the rule base and need to check it.

Severity Level 6 Error Message routine_name: row find error for indexes <classIdx>,<ruleIdx> Explanation row find error for indexes Recommended Action Find the Rule not to mach the class index.

Severity Level 6 Error Message routine_name: relevant class row find error for index <classIdx> Explanation relevant class row find error for index Recommended Action Find the Rule not to mach the class row

Severity Level 6 Error Message routine_name: relevant class rule row find error for indexes

<classIdx>,<ruleIdx> Explanation relevant class row find error for index Recommended Action Find the Rule not to mach the class index

Severity Level 6 Error Message routine_name: refclass row find error for index <refClassIdx> Explanation refclass row find error for index Recommended Action Find the Rule not to mach the refclass index

Severity Level 6 Error Message diffServClassDelete: couldn't delete rule <classRuleIndex> from

class <name> Explanation couldn't delete rule Recommended Action The calss rule index is not matched the class name and need to

check again.

Severity Level 6 Error Message diffServClassObjectSet: attempt to destroy the row failed Explanation attempt to destroy the row failed Recommended Action The row rule need to check again.


Severity Level 6 Error Message routine_name: Unable to obtain DiffServ trace buffer Explanation Unable to obtain DiffServ trace buffer Recommended Action The trace buffer is full or abnormal condition

Severity Level 6 Error Message routine_name: Error activating saved config -- using factory

defaults instead Explanation Error activating saved config Recommended Action The config file is corruptted and is reload the factory default.

Severity Level 6 Error Message diffServCnfgrFiniPhase1: Unable to delete DiffServ trace buffer Explanation Unable to delete DiffServ trace buffer Recommended Action The Tarce buffer is allocated by the other or full.

Severity Level 6 Error Message routine_name: Unconfig phase 2 function failed with

resp=<response>, reas=<reason> Explanation Unconfig phase 2 function failed Recommended Action The diffserv module is failed to init.

Severity Level 6 Error Message dsDistillerReset: Unable to delete TLV instances for policy

<policyIndex>, intf <intIfNum> Explanation Unable to delete TLV instances for policy Recommended Action The TLV instances are not matched the poicy index and

interface number.

Severity Level 6 Error Message dsDistillerInit: Key-to-index table exceeds maximum (keymax) Explanation Key-to-index table exceeds maximum Recommended Action The index table is exceed to maximum.

Severity Level 6 Error Message dsDistillerIntfEventNotify: error (rc=rc2) evaluating policy index

<policyIndex>, intf <intIfNum>, direction <ifDirection> Explanation error evaluating policy index Recommended Action The poicy index is not matched the interface number and

direction.


Severity Level 6 Error Message Policy invalid for service intf: policy <nameStr>, intIfNum

<intIfNum>, direction <ifDirection> Explanation Policy invalid for service interface Recommended Action The poicy is invlaid for the service interface.

Severity Level 6 Error Message dsDistillerPolicyEvaluate: build up or tear down error for policy

<policyIndex>, intIfNum <intIfNum>, direction <ifDirection> Explanation build up or tear down error for policy Recommended Action The poicy is failed to build up for the interface number and

direction.

Severity Level 6 Error Message dsDstlTlvInit: Unable to register with the TLV utility, rc=rc Explanation Unable to register with the TLV utility Recommended Action The TLV is failed to register

Severity Level 6 Error Message dsDstlTlvFini: Unable to Unregister with the TLV utility, rc=rc Explanation Unable to Unregister with the TLV utility Recommended Action Unable to release to the TLV utility

Severity Level 6 Error Message dsDstlTlvPolicyAddSeparate: TLV issued, but could not update

TLV issued flags for policy <policyIndex>, ifIndex <ifIndex> Explanation could not update TLV issued flags for policy Recommended Action The TLV flag is not updated for the poicy index and interface

number.

Severity Level 6 Error Message dsDstlTlvPolicyAddSeparate: Could not delete TLV for handle

<tlvHandle> Explanation Could not delete TLV for handle Recommended Action The TLV handle need to be checked again.

Severity Level 6 Error Message dsDstlTlvPolicyAddCombined: TLVs issued, but could not

update TLV issued flags for policy <policyIndex>, ifIndex <ifIndex>

Explanation DiffServ deletion TLV failure for interface Recommended Action The TLV is not matched for the interface number.


Severity Level 6 Error Message Unrecognized rowInvalidFlags <rowInvalidFlags> in class id Explanation Unrecognized rowInvalidFlags Recommended Action The class ID is invalid.

Severity Level 6 Error Message Unrecognized class rule entry type Explanation Unrecognized class rule entry type Recommended Action The Class rule is invalid.

Severity Level 6 Error Message Unrecognized rowInvalidFlags <rowInvalidFlags> in class rule id Explanation Unrecognized rowInvalidFlags Recommended Action The class rule id is invalid.

Severity Level 6 Error Message Unrecognized policy attribute entry type Explanation Unrecognized policy attribute entry type Recommended Action The poicy attribute is invalid

Severity Level 6 Error Message Unrecognized rowInvalidFlags <rowInvalidFlags> in policy attr id Explanation Unrecognized rowInvalidFlags Recommended Action The policy attr id is invlalid.

Severity Level 6 Error Message Unrecognized police action type Explanation Unrecognized police action type Recommended Action The poice action type is invalid.

Severity Level 6 Error Message diffServAclExtract: Unable to delete rules for class index Explanation Unable to delete rules for class index Recommended Action The rule class is invalid or protected by the system.


Severity Level 6 Error Message Number of fields in ACL rule exceeds DiffServ rules per class

limit Explanation Number of fields in ACL rule exceeds DiffServ rules per class

limit Recommended Action The ACL rule is exceed the Diffserv rules per class limit.

Severity Level 6 Error Message diffServPolicyAttrCreate: Error deleting row after create failure

for indexes Explanation Error deleting row after create failure for indexes Recommended Action The poicy attri is failed to create.

Severity Level 6 Error Message diffServPolicyAttrObjectSet: attempt to destroy the row failed Explanation attempt to destroy the row failed Recommended Action The diffServ policy attri is failed to set.

Severity Level 6 Error Message dsmibPolicyAttrIndexNextUpdate: ERROR -- could not find

policy instance row for indexes Explanation could not find policy instance row for indexes Recommended Action The policy instance is invalid.

Severity Level 6 Error Message routine_name: ERROR -- could not find policy instance row for

indexes <policyIndex>,<policyInstIndex>could not find policy instance row for indexes

Explanation could not find policy instance row for indexe Recommended Action The poicy instance is not found

Severity Level 6 Error Message diffServPolicyInstCreate: Error deleting row after create failure

for indexes Explanation Error deleting row after create failure for indexes Recommended Action The diffserv poicy is failed to create.

Severity Level 6 Error Message diffServPolicyInstDelete: couldn't delete attribute

<policyAttrIndex> from policy instance <policyInstIndex> Explanation couldn't delete attribute Recommended Action The poicy attribute is not matched the poicy instance.


Severity Level 6 Error Message diffServPolicyInstObjectSet: attempt to destroy the row failed Explanation attempt to destroy the row failed Recommended Action The diffserv poicy is failed to destroy.

Severity Level 6 Error Message dsmibPolicyInstIndexNextUpdate: ERROR -- could not find

policy row for index Explanation could not find policy row for index Recommended Action The poicy is not matched for the row for index.

Severity Level 6 Error Message dsmibPolicyPerfAttach: couldn't create Perf <pStr> row for

indexes <policyIndex>, <policyInstIndex> on intIfNum <intIfNum>

Explanation couldn't create Perf Recommended Action The poicy perf is failed to create.

Severity Level 6 Error Message dsmibPolicyPerfDetach: couldn't delete Perf <pStr> row for

indexes <policyIndex>, <policyInstIndex> on intIfNum <intIfNum>

Explanation couldn't delete Perf Recommended Action The poicy is not deleted perf.

Severity Level 6 Error Message diffServPolicyDelete: couldn't delete instance <policyInstIndex>

from policy <name> Explanation couldn't delete instance Recommended Action The policy is not deleted.

Severity Level 6 Error Message diffServPolicyObjectSet: attempt to destroy the row failed Explanation attempt to destroy the row failed Recommended Action The policy object is to destroy.

Severity Level 6 Error Message dsmibMibTableSizeCheck: table ID <tableId> size <tableSize>

exceeds maximum <tableMax> Explanation table ID exceeds Recommended Action The table ID exceeds maxium tableMax.


Severity Level 6 Error Message diffServServiceDelete: unable to delete Policy Perf Table row

for intf <intIfNum>, dir <ifDirection>, policy index <policyIndex Explanation unable to delete Policy Perf Table row Recommended Action The poicy perf table row is not matched.

Severity Level 6 Error Message diffServServiceObjectSet: unable to delete Policy Perf Table

row for intf <intIfNum>, dir <ifDirection>, policy index <prevPolicyIndex>

Explanation unable to delete Policy Perf Table row Recommended Action The poicy perf table is not deleted.

Severity Level 6 Error Message diffServServiceObjectSet: unable to create Policy Perf Table

row for intf <intIfNum>, dir <ifDirection>, policy index <prevPolicyIndex>

Explanation unable to create Policy Perf Table row Recommended Action The poicy perf is failed to create

Severity Level 6 Error Message diffServServiceObjectSet: attempt to destroy the row failed Explanation attempt to destroy the row failed Recommended Action The service object is failed to destroy.

Severity Level 6 Error Message diffServStandardMibInit: Unable to create draft MIB semaphoreExplanation Unable to create draft MIB semaphore Recommended Action The Diffserv is failed to create.

Severity Level 6 Error Message dsTraceModeApply: Unable to apply DiffServ trace mode

(mode), handle=<diffServTraceHandle> Explanation Unable to apply DiffServ trace mode Recommended Action The Apply trace mode is invalid.

Severity Level 6 Error Message Error while building contents of config Explanation Error while building contents of config Recommended Action The config is built for error


Severity Level 6 Error Message Error on call to osapiFsWrite routine for config file Explanation Error on call to osapiFsWrite routine for config file Recommended Action The config file cannot write into the system

Severity Level 6 Error Message Failed to reset DiffServ. Recommend resetting Explanation Failed to reset DiffServ. Recommend resetting Recommended Action The system is crazy to reset.

Severity Level 6 Error Message Error initializing DiffServ Explanation Error initializing DiffServ Recommended Action The Diffserv module is not init.

Severity Level 6 Error Message <File> <Line>: routine_name : Error Explanation open file error Recommended Action The file is invalid

Severity Level 6 Error Message Inconsistent row status value: expected=<rowStatus>

actual=<rowStatus> Explanation Inconsistent row status value Recommended Action The row status is inconsistent.

Severity Level 6 Error Message Corrupted contents for config file Explanation Corrupted contents for config file Recommended Action The config file is corruptted

Severity Level 6 Error Message Unknown Class Rule Type Explanation Unknown Class Rule Type Recommended Action The Class rule is unknown.

Severity Level 6 Error Message Unknown Policy Attribute Type Explanation Unknown Policy Attribute Type Recommended Action The policy attribute is unknown.


Severity Level 6 Error Message Error applying DiffServ config Explanation Error applying DiffServ config Recommended Action The diffserv config is applied error.

Severity Level 6 Error Message Error Initializing Standard MIB Explanation Error Initializing Standard MIB Recommended Action The MIB is wrong to init

Severity Level 6 Error Message WARNING: Invalid build - QOS DiffServ component not

initialized Explanation QOS DiffServ component not initialized Recommended Action The Diffserv is not initialized.


2.9 COS Messages

This section contains the COS module messages.

Severity Level 6 Error Message <routine_name>: Unable to apply saved config -- using factory

defaults instead Explanation Unable to apply saved config Recommended Action The file is corrupt and reset the factory default instead

Severity Level 6 Error Message <routine_name>: Cannot obtain default traffic class mapping for

IP Prec <L7_QOS_COS_MAP_NUM_IPPREC>, intf <intIfNum> Explanation Cannot obtain default traffic class mapping for IP Prec Recommended Action The setting config may be error.

Severity Level 6 Error Message <routine_name>: Cannot obtain default traffic class mapping for

IP DSCP <L7_QOS_COS_MAP_NUM_IPDSCP>, intf <intIfNum>

Explanation Cannot obtain default traffic class mapping for IP DSCP Recommended Action The setting config may be error.

Severity Level 6 Error Message <routine_name>: Global COS mapping table config is no longer

valid Explanation Global COS mapping table config is no longer valid Recommended Action The COS value is invalid for the system

Severity Level 6 Error Message <routine_name>: Failed applying config data to interface

<intIfNum> Explanation Failed applying config data to interface Recommended Action The interface number is invalid for the system.

Severity Level 6 Error Message <routine_name>: Failed applying COS map table config data to

interface <intIfNum> Explanation Failed applying COS map table config data to interface Recommended Action COS map table config to set to fail


Severity Level 6 Error Message <routine_name>: Failed applying COS queue config data to

interface <intIfNum> Explanation Failed applying COS queue config data to interface Recommended Action COS queue config to set to fail

Severity Level 6 Error Message <routine_name>: Intf <intIfNum> COS map table config is no

longer valid, using global defaults instead. Explanation COS map table config is no longer valid Recommended Action COS map table config is set to invalid

Severity Level 6 Error Message <routine_name>: Failed to apply default COS map table config

to interface <intIfNum> Explanation Failed to apply default COS map table config to interface Recommended Action The interface config is set invalid.

Severity Level 6 Error Message <routine_name>: Failed to apply default COS queue config to

interface <intIfNum> Explanation Failed to apply default COS map table config to interface Recommended Action The interface config is set invalid.

Severity Level 6 Error Message Error writing config file Explanation Error writing config file Recommended Action The config File is corrupt.

Severity Level 6 Error Message <routine_name>: Failed to restore COS factory defaults Explanation Failed to restore COS factory defaults Recommended Action The config is set invalid.

Severity Level 6 Error Message cosIntfIsConfigurable: Error accessing COS config data for

interface <intIfNum> Explanation Error accessing COS config data for interface Recommended Action The COS config is invalid.


Severity Level 5 Error Message cosIntfChangeCallback called outside permitted phase Explanation cosIntfChangeCallback called outside permitted phase Recommended Action The access data cannot permiited

Severity Level 6 Error Message Unable to set global IP precedence mapping on intf <intIfNum>

(prec=<prec> class=<Class>) Explanation Unable to set global IP precedence mapping on interface Recommended Action The interface is not suitable for the IP precedence mapping

setting

Severity Level 6 Error Message Unable to set default IP precedence mapping on intf <intIfNum>

(prec=<prec> class=<Class>) Explanation Unable to set default IP precedence mapping on interface Recommended Action The interface is not suitable for the IP precedence mapping

setting

Severity Level 6 Error Message Unable to set global default IP precedence mapping for

prec=<prec> traffic class=<Class> Explanation Unable to set global default IP precedence mapping Recommended Action The interface is not suitable for the IP precedence mapping

setting

Severity Level 6 Error Message Unable to set global IP DSCP mapping on intf <intIfNum>

(dscp=<dscp> class=<Class＞) Explanation Unable to set global IP DSCP mapping on interface Recommended Action The interface is not suitable for the IP DSCP mapping setting

Severity Level 6 Error Message Unable to set default IP DSCP mapping for intf <intIfNum>,

prec=<prec> class=<Class＞ Explanation Unable to set default IP DSCP mapping for interface Recommended Action The interface is not suitable for the IP DSCP mapping setting

Severity Level 6 Error Message Unable to set global default IP DSCP mapping for prec=<prec>

traffic class=<Class> Explanation Unable to set global default IP DSCP mapping Recommended Action The interface is not suitable for the IP DSCP mapping setting


Severity Level 6 Error Message Unable to set global <cosMapIntfModeStr> trust mode on intf

<intIfNum> Explanation Unable to set global trust mode on interface Recommended Action The interface is not suitable for the global trust mode setting

Severity Level 6 Error Message <routine_name>: Unable to apply port default traffic class COS

mapping to intf <intIfNum> Explanation Unable to apply default COS map table config to interface Recommended Action The interface is not suitable for the COS map table setting

Severity Level 6 Error Message <routine_name>: Unable to apply default COS map table config

to intf <intIfNum> Explanation Unable to apply default COS map table config to interface Recommended Action The interface is not suitable for the COS map table setting

Severity Level 6 Error Message Unable to apply COS queue defaults on intf <intIfNum> Explanation Unable to apply COS queue defaults on interface Recommended Action The interface is not suitable for the COS queue setting

Severity Level 6 Error Message Unable to restore global COS queue defaults on intf <intIfNum> Explanation Unable to restore global COS queue defaults on interface Recommended Action The interface is not suitable for the COS queue setting

Severity Level 6 Error Message Unable to set global COS shaping rate <val> on intf <intIfNum> Explanation Unable to set global COS shaping rate Recommended Action The interface is not suitable for the COS shaping rate

Severity Level 6 Error Message Unable to obtain COS <cosQueueMgmtTypeStr> drop parms for

intf <intIfNum>, queue <queue> Explanation Unable to obtain COS drop parms for interface Recommended Action The interface is not suitable for the COS drop parms


Severity Level 6 Error Message Unable to set global COS queue mgmt type

<cosQueueMgmtTypeStr> on intf <intIfNum> Explanation Unable to set global COS queue mgmt type on interface Recommended Action The interface is not suitable for the COS queue mgmt type

Severity Level 6 Error Message Unable to set global COS WRED decay exponent (<val＞) on intf

<intIfNum> Explanation Unable to set global COS WRED decay exponent on interface Recommended Action The interface is not suitable for the COS WRED decay exponent

Severity Level 6 Error Message Unable to set global COS minimum bandwidth config on intf

<intIfNum> Explanation Unable to set global COS minimum bandwidth config on

interface Recommended Action The interface is not suitable for the COS minimum bandwidth

Severity Level 6 Error Message Unable to get COS minimum bandwidth config from intf

<intIfNum> Explanation Unable to get COS minimum bandwidth config from interface Recommended Action The interface is not suitable for the COS minimum bandwidth

Severity Level 6 Error Message Unable to set global COS maximum bandwidth config on intf

<intIfNum> Explanation Unable to set global COS maximum bandwidth config on

interface Recommended Action The interface is not suitable for the COS maximum bandwidth

Severity Level 6 Error Message Unable to get COS maximum bandwidth config from intf

<intIfNum> Explanation Unable to get COS maximum bandwidth config from interface Recommended Action The interface is not suitable for the COS maximum bandwidth


Severity Level 6 Error Message Unable to set global COS scheduler type config on intf

<intIfNum> Explanation Unable to set global COS scheduler type config Recommended Action The interface is not suitable for the COS scheduler type

Severity Level 6 Error Message Unable to get COS scheduler type config from intf <intIfNum> Explanation Unable to get COS scheduler type config from intf <intIfNum> Recommended Action The interface is not suitable for the COS scheduler type

Severity Level 6 Error Message Unable to obtain COS <cosQueueMgmtTypeStr> drop parms for

intf <intIfNum>, queue <queue> Explanation Unable to obtain COS drop parms for interface Recommended Action The interface is not suitable for the COS drop parms

Severity Level 6 Error Message Unable to set global COS queue mgmt type on intf <intIfNum> Explanation Unable to set global COS queue mgmt type Recommended Action The interface is not suitable for the COS queue mgnt type

Severity Level 6 Error Message Unable to get COS queue mgmt type config from intf <intIfNum> Explanation Unable to get COS queue mgmt type config Recommended Action The interface is not suitable for the COS queue mgnt type

Severity Level 6 Error Message Unable to set global COS tail drop config for queue <queueId>

on intf <intIfNum> Explanation Unable to set global COS tail drop config for queue Recommended Action The interface is not suitable for the COS tail drop

Severity Level 6 Error Message Unable to get COS tail drop config from intf <intIfNum> Explanation Unable to get COS tail drop config Recommended Action The interface is not suitable for the COS tail drop


Severity Level 6 Error Message Unable to set global COS WRED config for queue <queueId> on

intf <intIfNum> Explanation Unable to set global COS WRED config Recommended Action The interface is not suitable for the COS WRED

Severity Level 6 Error Message Unable to get COS WRED config from intf <intIfNum> Explanation Unable to get COS WRED config Recommended Action The interface is not suitable for the COS WRED

Severity Level 6 Error Message COS mapping: Unable to apply IP Precedence <prec> to traffic

class <class> on intf <intIfNum> Explanation Unable to apply IP Precedence to traffic class Recommended Action The IP Precedence is not suitable for the setting

Severity Level 6 Error Message COS mapping: Unable to apply IP DSCP <DSCP> to traffic class

<class> on intf <intIfNum> Explanation Unable to apply IP DSCP to traffic class Recommended Action The IP DSCP is not suitable for the traffic class.

Severity Level 6 Error Message COS mapping: Invalid trust mode value (mode) on intf

<intIfNum> Explanation Invalid trust mode value Recommended Action The trust mode value is invalid.

Severity Level 6 Error Message COS mapping: Unable to obtain dot1p mapping table for intf

<intIfNum> Explanation Unable to obtain dot1p mapping table Recommended Action The dot1p mapping table is invalid.

Severity Level 6 Error Message COS mapping: Unable to apply trust mode <mode> on intf

<intIfNum> Explanation Unable to apply trust mode Recommended Action The trust mode is invalid.


Severity Level 6 Error Message COS queueing: Unable to apply COS intf config on interface

<intIfNum> Explanation Unable to apply COS intf config Recommended Action The COS inrf is invalid.

Severity Level 6 Error Message COS queueing: Unable to apply COS tail drop parms on intf

<intIfNum>, queue <queue> Explanation Unable to apply COS tail drop parms Recommended Action The COS tail drop parms

Severity Level 6 Error Message COS queueing: Unable to apply COS WRED parms on intf

<intIfNum>, queue <queue> Explanation Unable to apply COS WRED parms Recommended Action The COS WRED parms is invalid

Severity Level 5 Error Message Error initializing COS component Explanation Error initializing COS component Recommended Action The COS is failed to initailize


2.10 DOT1X Messages

This section contains the DOT1X module messages.

Severity Level 6 Error Message dot1xSave: Error on call to sysapiCfgFileWrite for config file

<Dot1x Config File Name> Explanation Failed saveing dot1x configuration. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message dot1xApiCnfgrCommand: Failed calling dot1xIssueCmd. Explanation Failed calling dot1xIssueCmd. Recommended Action The calling dot1IssueCmd is invalid.

Severity Level 6 Error Message dot1xInit: msgQueue creation error. Explanation Message queue creation error when system initialization for

dot1x component. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Failed to initialize dot1x outcalls Explanation Failed to inialize dot1x outcalls when the configurator control

commands/request pair init phase I. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Unable to create dot1xTrace block Explanation Unable to create dot1xTrace block when the configurator control

commands/request pair init phase I.* Trace create for debugging. This trace has 256 entries, each entry is 16 byte long. Actual user data available is 15 bytes as the first byte always records the trace id

Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Failed to enabling dot1x tracing Explanation Failed to enabling dot1x tracing when the configurator control

commands/request pair init phase 1. Recommended Action The dox1 mdoule is failed to init.


Severity Level 6 Error Message Unable to initialize dot1x debug Explanation Unable to initialize dot1x debug when the configurator control

commands/request pair init phase 1. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Failure in dot1xTxRxInit Explanation Failed to register function with sysnet to receive PDUs when the

configurator control commands/request pair init phase I. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message dot1x: Unable to register with NIM Explanation Unable to register with NIM when the configurator control

commands/request pair Init Phase 2. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message dot1x: Unable to register for RADIUS response callback Explanation Unable to register for RADIUS response callback when the

configurator control commands/request pair Init Phase 2. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Failed to create dot1x task Explanation Failed to create dot1x task when initialize dot1x tasks and data. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Unable to initialize dot1xTask() Explanation Unable to initialize dot1x task. Recommended Action The dox1 mdoule is failed to init.

Severity Level 6 Error Message Failed to create dot1x timer task Explanation Failed to create dot1x timer task when initialize dot1x tasks and

data. Recommended Action The dox1 mdoule is failed to init.


Severity Level 6 Error Message Unable to initialize dot1xTimerTask() Explanation Unable to initialize dot1x timer task when initialize dot1x tasks

and data. Recommended Action The dox1 mdoule is failed to init

Severity Level 6 Error Message dot1xCtlAdminModeDisable: could not set state to authorized,

intf <Interface Number> Explanation Could not set state to authorized when disable administrative

mode setting for dot1x. Recommended Action Cannot set the dot1x under the interface number, check the

interface number is available not.

Severity Level 6 Error Message Failure in applying config data for interface <Interface Number> Explanation Failure in applying config data for interface. Recommended Action The interface number is not available for the dot1x module.

Severity Level 6 Error Message dot1xIntfChangeCallback: Received an interface change

callback while not ready to receive it Explanation Received an interface change callback while not ready to

receive it. Recommended Action The interface number is not available for the dot1x module

Severity Level 6 Error Message dot1xIhProcessIntfChange L7_DOWN: failed sending terminate

cause, intf <Interface Number> Explanation Failed sending terminate cause when port down. Recommended Action Port down trap occurred.

Severity Level 6 Error Message dot1xIhProcessIntfChange L7_DISABLE: failed sending

terminate cause, intf <Interface Number> Explanation Failed sending terminate cause when port disabled. Recommended Action Port disable trap event


Severity Level 6 Error Message Error accessing dot1x config data for interface <Interface

Number> in dot1xIntfIsConfigurable. Explanation There is synchronization issue between NIM and components

w.r.t. interface creation/deletion. Recommended Action The dot1x system is crashed.

Severity Level 6 Error Message dot1xLocalAuthMd5ResponseValidate: couldn't allocate

responseData Explanation Couldn't allocate memory for MD5 challenge response

validation. Recommended Action MD5 messages is invalid.

Severity Level 6 Error Message dot1xRadiusAcceptProcess: EAP message not received from

server Explanation EAP message not received from radius server. Recommended Action The system is disconnected by the Radius Server.

Severity Level 6 Error Message dot1xRadiusAcceptProcess: error calling radiusAccountingStart,

ifIndex=<Interface Number> Explanation The port was previously unauthorized and send accounting start

to server failed. Recommended Action The Radius Process is abnormal.

Severity Level 6 Error Message dot1xRadiusChallengeProcess: Out of System buffers Explanation Out of system buffer while process RADIUS challenge from

server. Recommended Action The Radius Process is out of system memory.

Severity Level 6 Error Message dot1xRadiusAccountingStart: error calling

radiusAccountingStart, ifIndex=<Interface Index> Explanation The port was previously unauthorized and send accounting start

to server failed. Recommended Action The port setting is not available for the dot1x module.


Severity Level 6 Error Message dot1xRadiusAccountingStop: error calling

radiusAccountingStop, ifIndex=<Interface Index> Explanation Send accounting stop request failed. Recommended Action The dot1x & Radius is not syschonous

Severity Level 6 Error Message dot1xApmMachine: could not set state to unauthorized, intf

<Interface Number> Explanation If port is not operable, set it to unauthorized. Recommended Action The port is not operable.

Severity Level 6 Error Message dot1xApmDisconnectedAction: failed sending terminate cause,

intf <Interface Number> Explanation Failed sending terminate cause when the APM state

disconnected. Recommended Action The system is disconnected by the Radius server.

Severity Level 6 Error Message dot1xApmDisconnectedAction: could not set state to

unauthorized, intf <Interface Number> Explanation Could not set state to unauthorized in the APM state

disconnected. Recommended Action The system is disconnected by the Radius server.

Severity Level 6 Error Message dot1xApmForceAuthAction: could not set state to unauthorized,

intf <Interface Number> Explanation Could not set state to unauthorized in the APM state

authenticated. Recommended Action The system is disconnected by the Radius server.

Severity Level 6 Error Message dot1xApmHeldAction suppRestarting: failed sending terminate

cause, intf <Interface Number> Explanation Failed sending terminate cause supplicant restart. Recommended Action The system is terminate to send.


Severity Level 6 Error Message dot1xApmHeldAction reAuthenticating: failed sending terminate

cause, intf <Interface Number> Explanation Failed sending terminate cause reauthentication failure. Recommended Action The system is terminate to send.

Severity Level 6 Error Message dot1xApmHeldAction: could not set state to unauthorized, intf

<Interface Number> Explanation Could not set state to unauthorized in the APM state held. Recommended Action The authorized state is failed.

Severity Level 6 Error Message dot1xApmForceAuthAction: could not set state to authorized, intf

<Interface Number> Explanation Could not set state to authorized in the APM state forece

authorized. Recommended Action The state is unauthorized by the interface number.

Severity Level 6 Error Message dot1xApmForceUnauthAction: could not set state to

unauthorized, intf <Interface Number> Explanation Could not set state to unauthorized in the APM state force

unauthorized. Recommended Action The state is unauthorized by the interface number

Severity Level 6 Error Message dot1xApmForceUnauthAction: failed sending terminate cause,

intf <Interface Number> Explanation Failed sending terminate cause administrator reset. Recommended Action The state is unauthorized by the interface number.

Severity Level 6 Error Message dot1xBamResponseAction: failed getting auth method, intf

<Interface Number> Explanation If we couldn't get an auth method, log an error and fail the

authentication. Recommended Action The interface number is need to be authorized.


Severity Level 6 Error Message dot1xTxReqId: Out of System buffers Explanation Out of system buffers when transmit a EAPOL EAP Req/Id to

Supplicant. Recommended Action The EAPOL EAP is abnormal.

Severity Level 6 Error Message dot1xTxReq: Out of System buffers Explanation Out of system buffers when transmit a EAPOL EAP Request to

Supplicant. Recommended Action The EAPOL EAP is abnormal.

Severity Level 6 Error Message dot1xTxMd5Challenge: Out of System buffers Explanation Out of system buffers when transmit an EAP Request MD5

challenge to Supplicant. Recommended Action The EAPOL EAP is abnormal.

Severity Level 6 Error Message dot1xFrameTransmit: dtlPduTransmit failed Explanation A dot1x frame transmit failed. Recommended Action The system is disconnected.

Severity Level 6 Error Message dot1xRadiusAccessRequestSend failed Explanation Dot1x radius access request send failed. Recommended Action Access is failed.

Severity Level 6 Error Message received invalid dot1x status Explanation Received invalid dot1x status when set the authorization status

of the specified interface. Recommended Action The dot1x status is abnormal.


2.11 RADIUS Messages

This section contains the RADIUS module messages.

Severity Level 6 Error Message RADIUS: Accounting-Response failed to validate, id=<Header

ID> Explanation Failed to validate the Accounting-Response packet recieved

from the RADIUS server. Recommended Action The Radius Server need to be checked available or not.

Severity Level 6 Error Message RADIUS: Access-Challenge failed to validate, id=<Header ID> Explanation Failed to validate the Access-Challenge packet recieved from

the RADIUS server. Recommended Action The Radius Server need to be checked available or not.

Severity Level 6 Error Message RADIUS: Access-Reject failed to validate, id=<Header ID> Explanation Failed to validate the Access-Reject from the Radius server. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Access-Accpet failed to validate, id=<Header ID> Explanation Failed to validate the Access-Accpet from the Radius server. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Failed to validate Message-Authenticator, id=<Header

ID> Explanation Validate the Message-Authenticator failed Recommended Action The Radius Server need to be checked available or not.

Severity Level 6 Error Message RADIUS: Response is missing Message-Authenticator,

id=<Header ID> Explanation Response is missing Message-Authenticator when process

radius attributes. Recommended Action To check between the system and Radius Server, it will be

available or not.


Severity Level 6 Error Message RADIUS: Could not allocate a request buffer Explanation Could not allocate a request buffer when process radius request

Information. Recommended Action The Radius module is not available and check again.

Severity Level 6 Error Message RADIUS: Registrar ID <Registrar ID> greater then last

component ID Explanation The registrar ID greater then last component ID when process

radius response registration. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message radiusResponseDeregister registrar_ID <Component Id> greater

than L7_LAST_COMPONENT_ID Explanation The deregistrar ID greater than the last component ID. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message radiusResponseDeregister registrar_ID <Component Id> not

registered Explanation The deregistrar ID was not registered. Recommended Action The Radius module need to be checked the set configuration

Severity Level 6 Error Message RADIUS: could not get buffer Explanation Could not get attribute-value pair buffer. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Could not allocate requestInfo Explanation Could not allocate request Information when authenticate a user

with a RADIUS server. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Could not allocate accounting requestInfo Explanation Could not allocate accounting request Information when start the

accounting for the session. Recommended Action The Radius module is abnormal.


Severity Level 6 Error Message RADIUS: Failed to initialize the dictionary Explanation Failed to initialize the dictionary when radius client shutdown. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: could not save config file <Radius Config File Name> Explanation Failed to saves the RADIUS client configuration. Recommended Action The radius config file is corrupt instead of the factory default.

Severity Level 6 Error Message RADIUS: Msg Queue is full! Event: <Event ID> Explanation Add a command to the RADIUS client message queue is full. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Invalid event received Explanation Save an invalid event to a shared memory Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Unknown message event <Message Event> Explanation Dispatch an unknown event to a handling function. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Request not found for the response Explanation Request not found for the response when process a RADIUS

packet received from a server. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: radiusDictionaryInit() could not allocate memory Explanation Could not allocate radius dictionary memory. Recommended Action The Radius module is failed to int.


Severity Level 6 Error Message RADIUS: ATTRIBUTE entry invalid on line (<Line Number>) in

dictionary Explanation An invalid attribute entry in radius dictionary when initiate radius

dictionary. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Attribute name is too long on line (<Line Number>) in

dictionary Explanation Attribute name is too long in radius dictionary when initiate

radius dictionary. Recommended Action The name constant config uration need to define again.

Severity Level 6 Error Message RADIUS: Vendor name is too long on line (<Line Number>) in

RADIUS dictionary Explanation The Vendor name is too long in radius dictionary when initiate

radius dictionary. Recommended Action The name constant config uration need to define again.

Severity Level 6 Error Message RADIUS: VALUE entry invalid on line (<Line Number>) in

dictionary Explanation An invalid value entry in radius dictionary when initiate radius

dictionary. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Value name is too long on line (<Line Number>) in

dictionary Explanation The value name is too long in dictionary when initiate radius

dictionary Recommended Action The name constant config uration need to define again.

Severity Level 6 Error Message RADIUS: Value id is invalid on line (<Line Number>) in dictionaryExplanation An invalid value ID in dictionary when initiate radius dictionary. Recommended Action The Radius module is abnormal.


Severity Level 6 Error Message RADIUS: VENDOR entry invalid on line (<Line Number>) in

dictionary Explanation An invalid vendor name in dictionary when initiate radius

dictionary. Recommended Action The name constant config uration need to define again

Severity Level 6 Error Message RADIUS: Vendor Code is invalid on line (<Line Number>) in

dictionary Explanation An invalid vendor code in dictionary when initiate radius

dictionary. Recommended Action The Radius module is abnormal.

Severity Level 6 Error Message RADIUS: Unable to register for response callback Explanation Failed to register for debug user requests callback. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Failed to create socket Explanation Failed to create socket when open the UDP socket connections

for the RADIUS client. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Bind error Explanation Failed to socket bind when open the UDP socket connections for

the RADIUS client. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Could not allocate a buffer for the packet Explanation Could not allocate a buffer for radius packet received. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: osapiSocketRecvFrom returned error Explanation Failed to read the RADIUS response. Recommended Action The Radius module is failed to int.


Severity Level 6 Error Message RADIUS: Invalid packet length - <Packet Length> Explanation An invalid packet length from RADIUS response. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Server address doesn't match configured server Explanation The RADIUS server address doesn't match configured server. Recommended Action Check the IP address is wrong or not.

Severity Level 6 Error Message RADIUS: Invalid code - <Header Code> Explanation An Invalid code in RADIUS header contents. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Invalid data length - <Header Message Length> Explanation Invalid data length in RADIUS header contents. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Failed to send all of the request Explanation Failed to send a packet to the RADIUS server and increments

counters. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message RADIUS: Failed to send the request Explanation Failed to send the Packet to the RADIUS server. Recommended Action To check between the system and Radius Server, it will be

available or not.

Severity Level 6 Error Message UserMgr: Unable to create msg queue Explanation Unable to create message queue when Initialize the userMgr for

Phase 1. Recommended Action The Radius module is failed to int.


Severity Level 6 Error Message Unable to register User Manager for RADIUS response callback Explanation Unable to register User Manager for RADIUS response callback

when Initialize the userMgr for Phase 2. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Sever error, unable to create msg queue! Explanation Unable to create message queue when system initialization for

radius component. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Unable to initialize radius_task Explanation Failed to Initialize RADIUS client tasks. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Unable to initialize radius_rx_task Explanation Failed to initialize RADIUS RX task. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Unable to initialize radius_timer_task Explanation Failed to initialize RADIUS timer task. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Failed to create a task Explanation Failed to create RADIUS task. Recommended Action The Radius module is failed to int.

Severity Level 6 Error Message RADIUS: Sever error, no timers remain! Explanation RADIUS cLient timer task which serves the expired timers. Recommended Action The Radius module is failed to int.


Severity Level 6 Error Message RADIUS: Could not allocate ServerEntry Explanation Could not allocate memory for the entry and initialize the entry. Recommended Action The Radius module is failed to int.


2.12 TACACS Messages

This section contains the Tacacs module messages.

Severity Level 6 Error Message tacacsSave: Error on call to sysapiCfgFileWrite for config file

<TACACS Config File Name> Explanation Saves tacacs configuration failed. Recommended Action The Tacacs config file is corrupt instead of the factory default.

Severity Level 6 Error Message tacacsCtlAdminModeDisable: could not set state to authorized,

intf <Interface Number> Explanation Could not disable administrative mode setting for tacacs. Recommended Action The Tacacs module is failed to init.

Severity Level 6 Error Message <File Name>: <Line Number> : tacacsTxPacket: session is null Explanation Send a data packet to TACACS+ server and the session pointer

is null. Recommended Action The Tacacs system environment need to be verified.

Severity Level 6 Error Message <File Name>: <Line Number> : tacacsTxPacket: error encrypting

data(key:<Key>) Explanation Error encrypting data before send a data packet to TACACS+

server. Recommended Action The Tacacs system environment need to be verified.

Severity Level 6 Error Message <File Name>: <Line Number> : tacacsTxPacket: write to socket

fail Explanation Write to socket failed when send a data packet to TACACS+

server. Recommended Action The Tacacs system environment need to be verified.

Severity Level 6 Error Message <File Name>: <Line Number> : tacacsTxAuthenSTART: session

is null Explanation Send a TACACS+ authentication START packet and the session

pointer is null. Recommended Action The Tacacs system environment need to be verified.


2.13 BOOTP Client Messages

This section contains the BOOTP Client module messages.

Severity Level 6 Error Message do_bootp(): osapiNetIfConfig Failed for Service Interface Explanation Service interface configured fail. Recommended Action Check the Bootp Server or interface environment.

Severity Level 6 Error Message do_bootp():usmDbAgentIpIfAddressSet() returned failure. Explanation The system IP address set fail. Recommended Action The system IP address is failed to assign.

Severity Level 6 Error Message do_bootp(): osapiSetBroadAddr failed Explanation Broadcast Address of the interface set fail Recommended Action The system is connected to the Bootp Server unsucessfuly.

Severity Level 6 Error Message do_bootp():Timeout Explanation Soctet select timeout. Recommended Action The system is connected to the Bootp Server unsucessfuly.

Severity Level 6 Error Message do_bootp(): Error in Receiving the packet Explanation Packet receive fail Recommended Action The system is connected to the Bootp Server unsucessfuly.

Severity Level 6 Error Message Option not specified in the Vendor field. Possible Reason:This

Tag value not specified on BOOTP server. Explanation BOOTP option get fail Recommended Action The BOOTP Server is failed

Severity Level 6 Error Message getParamsFromBootpStruct():L7_bootp_option_get() returned

failure for netmask Explanation BOOTP option get fail Recommended Action The BOOTP Server is failed


Severity Level 6 Error Message L7_bootp():usmDbServicePortIPAddrSet() returned failure Explanation Service interface IP address set fail. Recommended Action The system of the IP address is failed to get to the BOOTP

Server.

Severity Level 6 Error Message L7_bootp():Conflict w/offered IP Addr, error=errormsg Explanation Service interface IP address set fail (IP Address conflict). Recommended Action IP address is failed to be assigned.

Severity Level 6 Error Message L7_bootp():getParamsFromBootpStruct()returned failure for

service port Explanation BOOTP option for service interface gets fail. Recommended Action The BOOTP server is failed.

Severity Level 6 Error Message L7_bootp():usmDbAgentIpIfAddressSet() returned failure Explanation Network interface IP address set fail. Recommended Action The IP address is falied to be assigned by the BOOTP Server

Severity Level 6 Error Message L7_bootp():getParamsFromBootpStruct()returned failure for

network interface Explanation BOOTP option for network interface gets fail. Recommended Action The IP address is falied to be assigned by the BOOTP Server


2.14 DHCP Client Messages

This section contains the DHCP CLIENT module messages.

Severity Level 6 Error Message dhcp_size():Bad DHCP cookie Explanation Cookie of the DHCP packet get fail. Recommended Action The DHCP server is failed to the system, the system need to be

verified.

Severity Level 6 Error Message dhcp_size(): Oversize DHCP packet in dhcp_size Explanation Fixed tag size of the DHCP packet is over. Recommended Action The system is abnormal to connect the DHCP system

Severity Level 6 Error Message Oversize DHCP packet in set_fixed_tag Explanation Fixed tag size of the DHCP packet is over. Recommended Action The system is abnormal to send messages to the DHCP system.

Severity Level 6 Error Message Wrong size in set_fixed_tag Explanation Fixed tag size of the DHCP packet is over. Recommended Action The system is abnormal to send messages to the DHCP system

Severity Level 6 Error Message Oversize DHCP packet in set_fixed_tag append Explanation DHCP packet size is over. Recommended Action The system is abnormal to send the messages to the DHCP

system

Severity Level 6 Error Message Oversize DHCP packet in set_fixed_tag Explanation Fixed tag size of the DHCP packet is over. Recommended Action The system is abnormal to send the messages to the DHCP.

Severity Level 6 Error Message Oversize DHCP packet in set_fixed_tag append Explanation Fixed tag size of the DHCP packet is over. Recommended Action The system is abnormal to send the messages to the DHCP.


Severity Level 6 Error Message usmDbServicePortIPAddrSet() returned failure Explanation Service interface IP address set fail. Recommended Action Fail to assign the IP Address

Severity Level 6 Error Message DbAgentIpIfAddressSet() returned failure Explanation Network interface IP address set fail. Recommended Action The assigned IP address is not the MAC address.

Severity Level 6 Error Message Conflict w/offered IP Addr, error=errorMsg Explanation Network interface IP address set fail (IP Address conflict). Recommended Action IP address is doublely assigned in the network segement.

Severity Level 6 Error Message msgQueue creation error for service port. Explanation Message queue for service port create fail. Recommended Action Network port are failed to create

Severity Level 6 Error Message TAG ID not found in the buffer Explanation TAG of DHCP packet search fail. Recommended Action The BOOTP system is abnormal condition.

Severity Level 6 Error Message dhcp_bind(): servPort dhcpstate failed Explanation Network interface state fail. Recommended Action The system is unavailable for the DHCP server and the

environment is need to be checked again.

Severity Level 6 Error Message usmDbDhcp_Client_Identifier_Tag():Oversize DHCP packet in

usmDbDhcp_Client_Identifier_Tag Explanation DHCP client identifier tag insert fail. Recommended Action Check the DHCP server system available or not


Severity Level 6 Error Message usmDbDhcp_Client_Identifier_Tag():Wrong size in

usmDbDhcp_Client_Identifier_Tag Explanation DHCP client identifier tag insert fail. Recommended Action Check the DHCP server system available or not

Severity Level 6 Error Message usmDbDhcp_Client_Identifier_Tag():Oversize DHCP packet in

usmDbDhcp_Client_Identifier_Tag append Explanation DHCP client identifier tag insert fail. Recommended Action Check the DHCP server system available or not


2.15 DHCP Relay Messages

This section contains the DHCP Relay module messages.

Severity Level 6 Error Message FILE LINE: dhcpRelaySave(): ERROR: Error on call to

dhcpRelaySave routine on config file dhcpRelay.cfg Explanation DHCP relay configuration file save fail. Recommended Action The system config is failed to set.

Severity Level 6 Error Message dhcpRelayCnfgrInitPhase1Process: Error allocating memory Explanation Memory allocate fail. Recommended Action The DHCP Relay is fail to init.

Severity Level 6 Error Message dhcpRelayCnfgrInitPhase1Process: Error allocating

DHCP_RELAY info structure Explanation Memory allocate fail. Recommended Action The DHCP Relay is fail to init

Severity Level 6 Error Message FILE LINE: dhcpRelayCnfgrInitPhase1Process(): Unable to

create DhcpRelayQueue Explanation Message queue create fail. Recommended Action The DHCP Relay is fail to init

Severity Level 6 Error Message dhcpRelayStartTasks: Failed to create DHCP_RELAY task Explanation Task create fail. Recommended Action The DHCP Relay is fail to init

Severity Level 6 Error Message dhcpRelayStartTasks: Unable to synchronize with

DHCP_RELAY task Explanation Task initialize fail. Recommended Action The DHCP Relay is fail to init


Severity Level 6 Error Message FILE LINE: dhcpRelayCnfgrParse(): Invalid command/request

pair Explanation Invalid command in configuration parse. Recommended Action The DHCP Relay is fail to init

Severity Level 6 Error Message dhcpRelay_Task: Received invalid message ID in DHCP Relay

message Explanation Receive worng message. Recommended Action The system is fail to communicate with the DHCP server.

Severity Level 6 Error Message REQUEST hops field more than config value Explanation Wrong hop value. Recommended Action The System is wrong to communicate with the DHCP.

Severity Level 6 Error Message Request's seconds field less than the config value Explanation Wrong min. waitting time value. Recommended Action The System is wrong to communicate with the DHCP.

Severity Level 6 Error Message processDhcpPacket: osapiSocketCreate failed creating server

socket Explanation Socket create fail. Recommended Action Communication error

Severity Level 6 Error Message processDhcpPacket: Failed binding address to socket Explanation Socket bind fail. Recommended Action Communication error

Severity Level 6 Error Message Request could not be relayed to Server Explanation Packet send fail. Recommended Action Check the remote DHCP server available not


Severity Level 6 Error Message processDhcpPacket: invalid DHCP packet type: TYPE Explanation Unknown DHCP packet type Recommended Action The Packet is wrong message.

Severity Level 6 Error Message Relay Packet Enqueue failed. Explanation Message send fail Recommended Action Check the remote DHCP server available not


2.16 DNS Relay Messages

This section contains the DNS Relay module messages.

Severity Level 6 Error Message Failed to Create DNS Relay Peer Task. Explanation DNS peer task create fail.. Recommended Action The system config is failed to set.

Severity Level 6 Error Message Failed to Create DNS Relay Task. Explanation DNS relay task create fail. Recommended Action The DNS Relay is fail to init.


2.17 DDNS Client

This section contains the DNS Client Module messages.

Severity Level 6 Error Message DDns : Bad Authentication - Username or Password on TZO Explanation Authentication failed. Recommended Action Check the username and password settings for DNS client.

Severity Level 6 Error Message DDns : The TZO account has expired Explanation The account has expired. Recommended Action Check the account with the DDNS service provider.

Severity Level 6 Error Message DDns : DDns update FAILURE <Host> mapping to <Address>

on <ServName> Explanation Fail to update the address with DDNS server. Recommended Action Check the network connectivity

2.18 sFlow Messages

This section contains the sFlow Module messages.

Severity Level 6 Error Message sFlowReceiverSampleDatagramHeaderWrite: IPv4 agent

address get failed. Explanation Can’t get the IPv4 address. Recommended Action Please check if the switch has configured with IPv4 address.


address get failed. Explanation Can’t get the IPv6 address. Recommended Action Please check if the switch has configured with IPv6 address.

Severity Level 6 Error Message sflowSave: Error on call to sysapiCfgFileWrite file <filename>. Explanation Can not save configuration value into config-file. Recommended Action The sflow config file is corrupt instead of the factory Factory.


Severity Level 6 Error Message Failure sending sFlow configurator init message. Explanation There is something wrong while the initialization of sFlow. Recommended Action Provide the message logs to your service provider for further

analysis.

Severity Level 6 Error Message sFlowTask(): Internal event msg receive failed Explanation The internal event queue for receiving event message is full. Recommended Action Event queue is full.

Severity Level 6 Error Message sFlowIntfChangeCallback: Received an interface change

callback while not ready to receive it Explanation Failure setting the sflow for an interface Recommended Action The sflow module is failed to init.

Severity Level 6 Error Message sflowTimerExpiryHdlr(): Sflow timer tick send failed Explanation Failed to send timer event to message queue. Recommended Action Timer queue is full.


address get failed Explanation Failed to get the IPv4 address of the sflow receiver Recommended Action To check if switch blade has been configured with IPv4 address.


address get failed Explanation Failed to get the IPv6 address of the sflow agent. Recommended Action To check if switch blade has been configured with the IPv6

address.


2.19 IGMP Snooping System Messages

This section contains the IGMP Snooping module messages.

Severity Level 6 Error Message Could not create task snoopTask Explanation The igmp snooping task can not create. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message Unable to initialize snoopTask() Explanation Initializing snoopTask fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message snoopTask(): invalid message type: Explanation Message tyep doesn't exist. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message snoopTimer(): snoopQueue has not been created Explanation Creating Message Queue fail. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message snoopTimer(): Snooping timer tick send failed Explanation Sending a message into message queue fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message snoopPacketHandle(): osapiMessageSend failed Explanation Sending a message into message queue fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message Failed to set global igmp snooping mode to (Enable/Disable) Explanation Setting global igmp snooping admin mode fail. Recommended Action The IGMP Snooping module is failed to init.


Severity Level 6 Error Message Failed to set igmp snooping mode (Enable/Disbale) for interface

number Explanation Setting the specific interface's admin mode fail. Recommended Action The interface number is failed to set.

Severity Level 6 Error Message Failed to set igmp mrouter mode (Enable/Disable) for interface

number Explanation Setting the specific interface's igmp mrouter mode fail. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message Failed to set igmp snooping mode (Enable/Disbale) for vlan Explanation Setting the specific vlan's igmp snpooping mode fail. Recommended Action The IGMP snooping is not set the vlan group successfully.

Severity Level 6 Error Message Failed to set igmp mrouter mode(Enable/Disbale) for interface

number on Vlan Explanation Setting the specific vlan and interface number mrouter mode fail.Recommended Action The specific vlan interface number is need to checked again.

Severity Level 6 Error Message snoopSave: Error on call to sysapiCfgFileWrite file

snoopCfgData.cfg Explanation Can not save configuration value into config-file. Recommended Action The igmp snooping config file is corrupt instead of the factory

Factory.

Severity Level 6 Error Message snoopInit: msgQueue creation error. Explanation Creating Message Queue fail. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message snoopCnfgrInitPhase1Process: Error allocating small buffers Explanation Memory Allocation fail. Recommended Action The IGMP Snooping module is failed to init.


Severity Level 6 Error Message IGMP Snooping: Unable to register with NIM Explanation Registering IGMP snooping to receive a callback fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message IGMP Snooping: Unable to register with MFDB Explanation Registering IGMP snooping to receive a callback fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message IGMP Snooping: Unable to register for VLAN change callback Explanation Registering IGMP snooping to receive a callback fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message IGMP Snooping: Unable to register for dot1s interface change

callback Explanation Registering IGMP snooping to receive a callback fail Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message Error accessing IGMP SNOOPING config data for interface

number in snoopMapIntfIsConfigurable. Explanation The interface number has not been created. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message Received an interface change callback while not ready to

receive it Explanation Receive a callback function, but not in execute phase or phase

3. Recommended Action The IGMP Snooping module is failed to init.

Severity Level 6 Error Message Received a mfdbentry callback while outside the EXECUTE

state Explanation Receive a callback function, but not in execute phase or phase

3. Recommended Action The IGMP Snooping module is failed to init.


2.20 SNTP Messages

This section contains the SNTP module messages.

Severity Level 6 Error Message sntpApiInit: cannot initialize API with cfg data Explanation Configuration data initialize fail. Recommended Action The SNTP module is failed to init.

Severity Level 6 Error Message sntpApiInit: cannot initialize API with server stats data Explanation Server status data initialize fail. Recommended Action The SNTP module is failed to init.

Severity Level 6 Error Message Error on call to sysapiCfgFileWrite routine on config file sntp.cfg Explanation Configuration file write fail. Recommended Action The SNTP config file is corrupt instead of the factory default.

Severity Level 6 Error Message sntpCnfgrInitPhase2Process: Could not register with nvStore Explanation Configuration file callback function register fail. Recommended Action The SNTP config file is corrupt instead of the factory default.

Severity Level 6 Error Message FILE: LINE: sntpCnfgrInitPhase3Process: SNTP Cfg unable to

read config file Explanation Configuration file read fail. Recommended Action The SNTP config file is corrupt instead of the factory default.

Severity Level 6 Error Message sntpCfgTask: Bad status on receive message from cfg queue

STATUS Explanation Receive worng message. Recommended Action The SNTP config file is corrupt instead of the factory default.

Severity Level 6 Error Message FILE: LINE: sntpCfgTaskCreate: Error allocating CFG data Explanation Memory allocate fail. Recommended Action The SNTP module is failed to init.


Severity Level 6 Error Message sntpCfgTaskCreate: Error starting SNTP Client Explanation SNTP Client initialize fail. Recommended Action The SNTP Client is failed to init.

Severity Level 6 Error Message sntpCfgTaskCreate: Unable to create SNTP processing task Explanation Task create fail. Recommended Action The SNTP Client is failed to init.

Severity Level 6 Error Message sntpCfgTaskCreate: Unable to syncronize with SNTP Cfg

processing task Explanation Task initialize fail. Recommended Action The SNTP Client is failed to init.

Severity Level 6 Error Message sntpLocalSocketOpen: osapiSetsockopt SO_BROADCAST

failed Explanation Socket option set fail. Recommended Action The SNTP module is failed to init.

Severity Level 6 Error Message SNTP: Can't join multicast group - errno ERROR NUMBER Explanation Socket option set fail. Recommended Action The muticast group need to be checked and match the SNTP

module.

Severity Level 6 Error Message sntpFlushReceiveBuffer: flushed NUMBER messages. Possible

attack in progress! Explanation Receice wong packet. Recommended Action The SNTP module is faile by the system.


2.21 VLAN Messages

This section contains the VLAN module messages.

Severity Level 6 Error Message dynamicToStaticVlanConvert: Failure to convert %d. Explanation Fail to convert the dynamic VLAN to static VLAN. Recommended Action The dynamic VLAN need to check the availability.

Severity Level 6 Error Message No available entries for vlan ID %d. Explanation There is no VLAN available. It reaches the max. VLAN entries in

system. Recommended Action The dynamic VLAN need to check the availability.

Severity Level 6 Error Message No available entries for vlan ID %d. Explanation There is no VLAN available. It reaches the max. VLAN entries in

system. Recommended Action The VLAN table is exceeded to the system limitation.

Severity Level 6 Error Message Attempt to create a vlan with an invalid vlan id %d Explanation The range of the VLAN id is invalid. Recommended Action To create a VLAN ID in the support range.

Severity Level 6 Error Message Unable to obtain permission from the Resource Manager to

create VLAN vlan id %d Explanation Unable to obtain permission from external resource manager to

create resource. Recommended Action The VLAN module is failed to init.

Severity Level 6 Error Message Creation of vlan %d failed Explanation Fail to create a specific VLAN. Recommended Action Need to check the VLAN ID is available or not.


Severity Level 6 Error Message Modification of vlan %d attempted before bridge initialized Explanation Dot1q is not initialized before attempting to modify a specific

VLAN. Recommended Action The VLAN module is failed to init.

Severity Level 6 Error Message Modify of vlan %d failed Explanation Fail to modify the VLAN. Recommended Action The VLAN module is failed to init.

Severity Level 6 Error Message Problem updating persistent data for VLAN %d Explanation Fail to update database with the new VLAN information. Recommended Action Check the current VLAN configuration set.

Severity Level 6 Error Message Problem updating data for VLAN %d Explanation Fail to add the entry to the main tree. Recommended Action Check the current VLAN configuration set.

Severity Level 6 Error Message Cannot find vlan %d to delete Explanation Can’t find the VLAN for deletion. Recommended Action Check the current VLAN configuration set.

Severity Level 6 Error Message Problem deleting data for VLAN %d Explanation Fail to delete the VLAN. Recommended Action Check the current VLAN configuration set.

Severity Level 6 Error Message Received a interface callback while outside the EXECUTE state Explanation Processing a message outside the correct phase state. Recommended Action The VLAN module is failed to init.


2.22 SPAN TREE Messages

This section contains the span tree module messages.

Severity Level 6 Error Message Dot1s registrar ID greater than Last Component ID Explanation Dot1s module is not registered Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Received a vlan callback while outside the EXECUTEstate Explanation Dosts module is not ready Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Error on call to sysapiCfgFileWrite routine on configfile Explanation Failure writing data to configuration file Recommended Action The span tree config file is corrupt instead of the factory default.

Severity Level 6 Error Message Error on call to osapiFsWrite routine on config file Explanation Error on call to osapiFsWrite routine on config file Recommended Action The span tree config file is corrupt instead of the factory default.

Severity Level 6 Error Message dot1sInit: msgQueue creation error. Explanation Failure creating message queue Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message dot1sInit: timer task creation error. Explanation Failure creating timer task Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to initialize dot1s_timer_task Explanation Failure initializing timer task Recommended Action The Span Tree module is failed to init.


Severity Level 6 Error Message dot1sInit: task creation error. Explanation Failure creating initiate task Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to initialize dot1s_task Explanation Failure creating dot1s main task Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to register for NIM Interface change callback! Explanation Failure registering callback function to NIM module Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to register for VLAN change callback! Explanation Failure registering callback function to VLAN module Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to register for dot1s state callback with DTL! Explanation Failure registering callback function to DTL module Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to register for dot1s state callback with Sysnet! Explanation Failure registering callback function to Sysnet module Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Unable to delete MSTP Instance in the hardware Explanation Failure deleting MSTP instance Recommended Action The config file need to be checked by the system setting

environment.

Severity Level 6 Error Message Dot1s Msg Queue is full!!!!Event: %u, on interface: %u,for

instance: %u Explanation The message queue is full Recommended Action The Span Tree module is failed to init.


Severity Level 6 Error Message Received a vlan callback while outside the EXECUTE state Explanation Dosts module is not ready Recommended Action The Span Tree module is failed to init.

Severity Level 6 Error Message Invalid intIfNum Explanation Interface number is incorrect Recommended Action The interface number is invalid by the system configuration.

Severity Level 6 Error Message dot1sIhSetPortState: Invalid MSTP state! Explanation The Mstp state is incorrect Recommended Action The MSTP state is abnormal.

Severity Level 6 Error Message Error accessing DOT1S config data for interface %d in

dot1sMapIntfIsConfigurable. Explanation Table management error synchronization issue between NIM

and components Recommended Action The span tree config file is corrupt instead of the factory default.

Severity Level 6 Error Message Unexpected Header Version= %d expecting %d Explanation The configuration file version is incorrect Recommended Action The config file is wrong.

Severity Level 6 Error Message File %s: Forced truncation of interface configuration migration at

%d entries Explanation Failure migrating configuration file Recommended Action The config file is corrupt instead of the fatory default.

Severity Level 6 Error Message Unexpected Header Version= %d expecting %d Explanation The configuration file version is incorrect Recommended Action The config file is corrupt instead of the fatory default.


Severity Level 6 Error Message dot1s Event out of range %d Explanation The Dot1s event is incorrect Recommended Action The system environment is abnormal.

Severity Level 6 Error Message Discarding BPDU:Cannot process BPDU on port(%d) until

migration timer expires Explanation Dot1s state machine is busy now Recommended Action The system environment is busy and wait for a while.

Severity Level 6 Error Message dot1sBpduTransmit(): could not get a buffer Explanation System resource is not enough for a new BPDU packet Recommended Action The system environment is busy and wait for a while.

Severity Level 6 Error Message dot1sBpduReceive(): Unable to put BPDU on Msg Queue Explanation The BPDU message queue is full or system has problem Recommended Action The span tree module is needed to be verified.

Severity Level 6 Error Message dot1sBpduReceive(): paddedBufHandle is L7_NULL Explanation System resource is not enough for a padded buffer Recommended Action he system environment is busy and wait for a while.

Severity Level 6 Error Message dot1sMstpTx(): CIST Role Disabled Explanation The CIST port role is disabled, do not transmit the packet Recommended Action The network environment need to be verified.

Severity Level 6 Error Message dot1sMstpTx(): MSTI Role Disabled Explanation The MIST port role is disabled, do not transmit the packet Recommended Action The network environment need to be verified.


2.23 STORM CONTROL Messages

This section contains the storm control module messages.

Severity Level 6 Error Message Failure setting interface <intIfNum> broadcast storm mode to

<mode> Explanation Failure setting the broadcast mode for an interface. Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message Failure setting interface <intIfNum> flow control mode to

<mode> Explanation Failure setting the flow control for an interface Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message policyApplyIntfConfigData: error returned from

policyIntfBcastCtrlLimitApply() for intIfNum=<intIfNum> Explanation Failure setting the broadcast rate limiting for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfFlowCtrlModeApply() setting intIfNum=<intIfNum> to mode=<mode>

Explanation Failure setting the flow control for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfMcastCtrlLimitApply() for intIfNum=<intIfNum> Explanation Failure setting the multicast rate limiting for an interface Recommended Action The interface number need to be checked available by the

system.



policyIntfMcastCtrlModeApply() setting intIfNum=<intIfNum> to mode=<mode>

Explanation Failure setting the multicast mode for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfDlfCtrlLimitApply() for intIfNum=<intIfNum> Explanation Failure setting the unicast rate limiting for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfDlfCtrlModeApply() setting intIfNum=<intIfNum> to mode=<mode>

Explanation Failure setting the unicast mode for an interface Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message Error on call to osapiFsWrite routine on config file policy.cfg Explanation check for file saving Recommended Action The storm control config file is corrupt instead of the factory

default.

Severity Level 6 Error Message Error on call to policyMapIntfIsConfigurable routine outside the

EXECUTE state Explanation routine outside the state Recommended Action The storm control config file is corrupt instead of the factory

default.

Severity Level 6 Error Message Error accessing POLICY config data for interface <intIfNum> in

policyMapIntfIsConfigurable. Explanation verify that the configId in the config data table entry matches the

configId that NIM maps to the intIfNum we are considering Recommended Action The storm control config file is corrupt instead of the factory

default.


Severity Level 6 Error Message Error on call to policyMapIntfIsConfigEntryGet routine outside

the EXECUTE state Explanation Error on call to policyMapIntfIsConfigEntryGet routine outside

the EXECUTE state Recommended Action The storm control config file is corrupt instead of the factory

default.

Severity Level 6 Error Message policyIntfDetach: error returned from

policyIntfFlowCtrlModeApply() setting intIfNum=<intIfNum> to mode=0

Explanation Failure setting the flow control for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfBcastCtrlModeApply() setting intIfNum=<intIfNum> to mode=0

Explanation Failure setting the broadcast mode for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfBcastCtrlLimitApply() for intIfNum=<intIfNum> Explanation Failure setting the broadcast rate limiting for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfMcastCtrlModeApply() setting intIfNum=<intIfNum> to mode=0

Explanation Failure setting the multicast mode for an interface Recommended Action The interface number need to be checked available by the

system.


policyIntfMcastCtrlLimitApply() for intIfNum=<intIfNum> Explanation Failure setting the multicast rate limiting for an interface Recommended Action The interface number need to be checked available by the

system.



policyIntfDlfCtrlModeApply() setting intIfNum=<intIfNum> to mode=0

Explanation Failure setting the unicast mode for an interface Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message policyIntfDetach: error returned from policyIntfDlfCtrlLimitApply()

for intIfNum=<intIfNum> Explanation Failure setting the unicast mode for an interface Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message policyIntfDetach: error returned from policyIntfDlfCtrlLimitApply()

for intIfNum=<intIfNum> Explanation Failure setting the unicast rate limiting for an interface Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message policyIntfChangeCallback: Received an interface event callback

while not in EXECUTE state. Explanation Failure setting the unicast rate limiting for an interface Recommended Action The storm control module is failed to init.

Severity Level 6 Error Message Failure setting interface <intIfNum> multicast storm mode to

<mode> Explanation Failure setting the multicast mode for an interface Recommended Action The interface number need to be checked available by the

system.

Severity Level 6 Error Message Failure setting interface <intIfNum> unicast storm mode to

<mode> Explanation Failure setting the unicast mode for an interface Recommended Action The interface number needs to be checked available by the

system.


Severity Level 1 Error Message broadcast storm detected on <intIfNum>. A packet filter action

has been applied on the interface. Explanation Broadcast storm is detected on interface <intIfNum>. Recommended Action Check the network environment and remove the cause of

broadcast storm.

Severity Level 1 Error Message multicast storm detected on <intIfNum>. A packet filter action

has been applied on the interface. Explanation Multicast storm is detected on interface <intIfNum>. Recommended Action Check the network environment and remove the cause of

multicast storm.

Severity Level 1 Error Message unicast storm detected on <intIfNum>. A packet filter action has

been applied on the interface. Explanation Unicast storm is detected on interface <intIfNum>. Recommended Action Check the network environment and remove the cause of

unicast storm.

Severity Level 1 Error Message broadcast storm control stop to filter packet on interface

<intIfNum>. Explanation broadcast storm is stopped on interface <intIfNum>. Recommended Action Check the network environment and remove the cause of

broadcast storm.

Severity Level 1 Error Message multicast storm control stop to filter packet on interface

<intIfNum>. Explanation multicast storm is stopped on interface <intIfNum>. Recommended Action Check the network environment and remove the cause of

multicast storm.

Severity Level 1 Error Message unicast storm control stop to filter packet on interface

<intIfNum>. Explanation unicast storm is stopped on interface <intIfNum>. Recommended Action Check the network environment and remove the unicast storm.


Severity Level 1 Error Message Broadcast storm control shutdown interface <intIfNum>. Explanation Interface <intIfNum> is shutdown by broadcast storm while

broadcast storm is detected on <intIfNum>. Recommended Action Check the network environment and remove the cause of

broadcast storm. Then, use ‘no shutdown’ command to enable <intIfNum> again. Or use ‘errdisable recovery’ feature to enable the interface automatically.

Severity Level 1 Error Message Multicast storm control shutdown interface <intIfNum>. Explanation Interface <intIfNum> is shutdown by multicast storm while

multicast storm is detected on <intIfNum>. Recommended Action Check the network environment and remove the cause of

multicast storm. Then, use ‘no shutdown’ command to enable <intIfNum> again. Or use ‘errdisable recovery’ feature to enable the interface automatically.

Severity Level 1 Error Message Unicast storm control shutdown interface <intIfNum>. Explanation Interface <intIfNum> is shutdown by unicast storm while unicast

storm is detected on <intIfNum>. Recommended Action Check the network environment and remove the cause of

unicast storm. Then, use ‘no shutdown’ command to enable <intIfNum> again. Or use ‘errdisable recovery’ feature to enable the interface automatically.


2.24 Port-Monitor Messages

This section contains the Port-Monitor module messages.

Severity Level 6 Error Message nimIntfQuery failed for intIfNum <intIfNum> Explanation Determine if the interface is attached Recommended Action The interface need to check the attached available or not.


mirrorCfgData.cfg Explanation check for file saving Recommended Action The config file is corrupt instead of fatory-default.

Severity Level 6 Error Message mirrorIntfChangeCallback: Received an interface event callback

while not in EXECUTE state Explanation routine outside the state Recommended Action The port-monitor module is failed to init.

Severity Level 6 Error Message Mirroring: Failed to notify components of probe status change Explanation Notify all interested components of an Interface Change event Recommended Action The port-monitor module is failed to init.


2.25 SNMP Messages

This section contains the SNMP module messages.

Severity Level 6 Error Message Failed to Create SNMP Task. Explanation (1) Failed to Create SNMP Task.

(2) Failed to Create SNMP Task that save config to flash Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message Failed to create SNMP proc monitoring task Explanation Failed to create SNMP proc monitoring task Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message Failed to Create SNMP Cable Test Task. Explanation Failed to Create SNMP Cable Test Task. Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message Failed to Create SNMP Config Task. Explanation Failed to Create SNMP Config Task. Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message Failed to Create RMON Task. Explanation Failed to Create RMON Task. Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message Error on call to sysapiCfgFileWrite routine on config file Explanation Failed to save SNMP user config file to NVStore Recommended Action The snmp config file is corrupt instead of the factory default.

Severity Level 6 Error Message SNMP User Config returned failure. Explanation Waits for SNMP agent to be ready before applying configuration Recommended Action The SNMP config is failed to init.


Severity Level 6 Error Message Error on call to osapiFsWrite routine on config file

trapCfgData.cfg Explanation Configuration file write fail. Recommended Action The snmp config file is corrupt instead of the factory default.

Severity Level 6 Error Message Failed registration for DTL_EVENT_PORT_BSR_TRAP_ENTRYExplanation Trap management callback function register fail. Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message Failed registration for DTL_EVENT_PORT_BSR_TRAP_EXIT Explanation Trap management callback function register fail. Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message TRAPMGR: Failed to register with CARDMGR Explanation Trap management callback function register fail. Recommended Action The SNMP module is failed to init.

Severity Level 6 Error Message TRAPMGR: component ID NUMBER greater than or equal to

L7_LAST_COMPONENT_ID Explanation Event callback function registration fails. Recommended Action The SNMP module is failed to init.


2.26 PING & TRACEROUTE Utility Messages

This section contains the PING & TRACEROUTE module messages.

Severity Level 6 Error Message ERROR (-1) Explanation Ping task delete fail Recommended Action The network environment needs to be checked.

Severity Level 6 Error Message ping: bad host! Explanation Ping with wrong host address. Recommended Action Check the host Ip address.

Severity Level 6 Error Message ping: socket failed in configure_socket Explanation Socket create fail. Recommended Action The system need to be connected or not.

Severity Level 6 Error Message Ping task create fail. Explanation Ping task create fail. Recommended Action The ping module is failed to init.

Severity Level 6 Error Message ping: Error in transmitEchoMessage Explanation Packet transmit fail. Recommended Action Check the network environment available or not.

Severity Level 6 Error Message ping: sendto error Explanation Packet transmit fail. Recommended Action Check the network connecting environment available or not.

Severity Level 6 Error Message wrote NUMBER1 bytes to X.X.X.X, return = NUMBER2 bytes Explanation Packet transmit fail(wrong length). Recommended Action Check the network connecting environment available or not.


Severity Level 6 Error Message ping: recvfrom error Explanation Packet receive fail Recommended Action Check the network connecting environment available or not.

Severity Level 6 Error Message traceroute: Failed to create ICMP socket Explanation Socket create fail. Recommended Action Check the network connecting environment available or not.

Severity Level 6 Error Message traceroute: Failed to create a UDP socket Explanation Socket create fail. Recommended Action Check the network connecting environment available or not.


2.27 TFTP/FTP Messages

This section contains the TFTP/FTP module messages.

Severity Level 6 Error Message Error while getting the file Explanation File get fail. Recommended Action The file gets the wrong file.

Severity Level 6 Error Message Error while putting the file Explanation File put fail. Recommended Action The file put the wrong file.

Severity Level 6 Error Message Wrong value for TFTP command Explanation Wrong TFTP command. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message error while writing the file Explanation File write fail. Recommended Action The file writes the wrong file.

Severity Level 6 Error Message Error while reading the buffer Explanation Buffer read fail. Recommended Action The file read the wrong file.

Severity Level 6 Error Message Error while putting data into the file Explanation File write fail. Recommended Action The file writes the wrong file.

Severity Level 6 Error Message Wrong value of mode entered Explanation Wrong TFTP mode. Recommended Action The TFTP process is wrong to check the network environment.


Severity Level 6 Error Message Error while opening the file Explanation File open fail. Recommended Action The file writes the wrong file.

Severity Level 6 Error Message tftp_get(): Failed to create socket Explanation Socket create fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_get(): Bind error Explanation Socket bind fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_get(): Send to error Explanation Packet send fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message No reply from TFTP server--Connection Timeout Explanation Socket select time out. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_get(): Send to error Explanation Packet send fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_get(): Recv from error Explanation Packet receive fail Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message Server Error message is: ERROR MSG With error code::

ERROR CODE Explanation TFTP transfer has error. Recommended Action The TFTP process is wrong to check the network environment.


Severity Level 6 Error Message Wrong protocol being used Explanation TFTP transfer has error. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_put(): Failed to create socket Explanation Socket create fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_put(): Bind error Explanation Socket bind fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_put(): Send to error Explanation Packet send fail. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message TFTP Timeout no reply from TFTP server Explanation Socket select time out. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message tftp_put(): recv from error Explanation Packet receive fail Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message Wrong protocol used Explanation TFTP transfer has error. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message TFTP Timeout no ACK from TFTP server... aborting transfer Explanation Socket select time out. Recommended Action The TFTP process is wrong to check the network environment.


Severity Level 6 Error Message TFTP Timeout no ACK from TFTP server... aborting transfer Explanation Socket select time out. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message TFTP Timeout TIME no ACK from TFTP server... resending

block Explanation Socket select time out. Recommended Action The TFTP process is wrong to check the network environment.

Severity Level 6 Error Message Send block BLOCK NUMBER1, got ACK for #BLOCK

NUMBER2 Explanation server acknowledgement block# not matches with the block# of

data sent Recommended Action The TFTP process is wrong to check the network environment.


2.28 Timer Messages

This section contains the TIMER module messages.

Severity Level 6 Error Message Timer Index Explanation Timer callback function executes fail. Recommended Action The Timer Module is failed to init.

Severity Level 6 Error Message Timer Function Pointer Explanation Timer callback function adds fail. Recommended Action The Timer Module is failed to init.


2.29 Stacking Messages

This section contains the Stacking Module messages.

Severity Level 6 Error Message Minimum required F/W revision <firmware version> is detected

on unit <unitID>. Explanation The latest firmware version is found on the stack member. Recommended Action To upgrade whole stacking to this firmware version from stack

master.

Severity Level 6 Error Message Firmware download on unit <unit-id> is successfully. Explanation The latest firmware image is updated successfully on unit

<unit-id> Recommended Action The lastest firmware image is updated successfully.

Severity Level 6 Error Message Firmware auto-upgrade on unit <unit-id> is successfully. Unit

<unit-id> will be reloaded. Explanation The auto-upgrade process is executed for <unit-id> and unit

<unit-id> device will be reload to apply the upgraded firmware. Recommended Action To wait the switch to join the stack.

Severity Level 6 Error Message Unit <unit-id> changes booting mode to <switch/IBP> Explanation Unit <unit-id> changes booting mode to switch or IBP. Recommended Action A reboot process is required to run the device in new mode.

Severity Level 6 Error Message Version mismatch on unit <unit-id> is detected. Issue the

auto-download processes. Explanation A FW mismatch version is detected on <unit-id> and the auto

download process is being executed. Recommended Action During the download process, please do not remove the target

device.

Severity Level 6 Error Message Delete cfg mismatched entry for unit <unit-id> Explanation A unit is found on the previous entry of configuration mismatched

unit. System will delete this entry and recreate the new one for current detected unit.

Recommended Action To wait the new unit to join the stack.


Severity Level 6 Error Message Different type of Connection Blade is detected on stack member

<unit-id>. Explanation Different type of connection blade is detected on stack member. Recommended Action Remove this mismatched connection blade from the stack or use

command, “switch <unit-id> bootmode <switch|IBP>” to change the mode to be the same as the stack master. After the mode is changed via the provided command, the mismatched connection blade will be reloaded automatically.

Severity Level 1 Error Message out of stack members, please pull out the cable and make sure

only maximum 8 units in a stack Explanation The stack member is exceeded max supported number in a

stack. Recommended Action Remove this connection blade from the stack.

Severity Level 1 Error Message Running code version not available, aborting discovery message

send. Explanation Can’t find the running code version. Recommended Action Checking if there is any default booting image in the flash.

Severity Level 1 Error Message Flash code version not available, aborting discovery message

send Explanation Can’t find the code version in the flash. Recommended Action Checking if there is any default booting image in the flash.

Severity Level 1 Error Message Problem sending discovery message on unit <unit-id> Explanation The discovery messages can’t be sent out. Recommended Action Please check the stacking cable is connected.

Severity Level 1 Error Message Failure while attempting to delete management unit Explanation Can’t delete the management unit. Recommended Action Please do not delete the management unit.


Severity Level 0 Error Message User reset unit <unit-id> Explanation Unit <unit-id> is reset by user. Recommended Action The unit is reset from stack master.

Severity Level 6 Error Message Fail to send RESET command to unit <unit-id>. Explanation Fail to send RESET command to unit <unit-id>. Recommended Action Check the stacking cable is connected probably or not.

Severity Level 6 Error Message Failure propagating config info from non-management unit Explanation Only management unit could propagate the Config info to stack

members. Recommended Action Configuration file is only allowed to be distributed by stack

master.

Severity Level 6 Error Message Startup Config propagation compete Explanation Startup configuration file propagation is successful Recommended Action The configuration is propogated successfully.

Severity Level 4 Error Message Startup Config propagation failed Explanation Startup configuration propagation failed Recommended Action Checking the stacking cable if it is connected probably or not.

Severity Level 6 Error Message Running Config propagation failed Explanation Running configuration propagation failed Recommended Action Checking the stacking cable if it is connected probably or not.

Severity Level 6 Error Message Request configuration file download [2] to unit <unit-id> failed

rc=<reason> Explanation Fail to send the request to unit <unit-id> for configuration file

downloading. Recommended Action Checking the stacking cable if it is connected probably or not.


Severity Level 6 Error Message Unit: <unit-id>: Can't send ekeying status Explanation eKeying status can’t be sent from stack member to stack master.Recommended Action Checking the stacking cable if it is connected probably or not.

Severity Level 6 Error Message Unit <unit-id> attached successfully Explanation Unit is attached successfully in the stack. Recommended Action Unit is ready for operation.

Severity Level 6 Error Message Error: usp <unit>/<slot>/<port>: Card Not Attached,

cmd=<cmd>, count=<count>, task: <taskname> Explanation Interface unit/slot/port is not presented so that the command

<cmd> can’t be applied to the chipset. Recommended Action Just a notice. After the interface is attached, the configuration

will be applied to the chipset automatically.

Severity Level 6 Error Message Stack Port Link Up: Index: 100 Unit: 1 Tag: Stack 1 Explanation The stack port (Stack 1) of unit ID 1 is link up. Recommended Action The stack port is link up. You could check if the new unit is joined

to the stack.

Severity Level 6 Error Message Stack Port Link Up: Index: 101 Unit: 1 Tag: Stack 2 Explanation The external stack port (Stack 2) of unit 1 is link up. Recommended Action The external stacking port is link up on unit 1.

Severity Level 6 Error Message Stack Port Link Down: Index: 100 Unit: 1 Tag: Stack 1 Explanation The stack port (Stack 1) of unit ID 1 is link down. Recommended Action User should check if the internal stacking link is disabled from

MMB.

Severity Level 6 Error Message Stack Port Link Down: Index: 101 Unit: 1 Tag: Stack 2 Explanation The external stack port (Stack 2) of unit 1 is link down. Recommended Action User should check if the external stacking cable is removed.

Please reconnect the stacking cable if you want to maintain the original stack.


Severity Level 6 Error Message Unit <unit-id> attached successfully Explanation The unit attached successfully to the stack. Recommended Action The unit is attached to the stack system and it is ready for

operation.

Severity Level 6 Error Message EDB Callback: Unit Join: <unit-id> Explanation The unit is detected by the switch and updated to its database. Recommended Action A notification message for the new detected unit.

Severity Level 6 Error Message EDB Callback: Unit Leave: <unit-id> Explanation The unit is removed from the stack due to the hardware is

removed or the stacking cable is removed. Recommended Action A notification message for user that a unit is removed.

Severity Level 1 Error Message Standby taking over as Manager of the Stack, reason: <reason> Explanation The standby unit has been taken over the master role due to the

reason. Recommended Action A notification message for user that a master is lost and standby

unit take over as Manager of the stack.

Severity Level 4 Error Message Unit <unit-id> active image version does not match with

Manager. Ports on this unit will not be operational. Explanation A new unit can’t be joined the stack due to the code version

mismatched. Recommended Action Image upgrade operation is recommended for the new unit.

Severity Level 5 Error Message Management unit conflict was detected and this unit has won the

manager election. All the units attached to losing Stack Manager %x:%x:%x:%x:%x:%x will reset and join this Manager.

Explanation Two stack masters in a stack, the current stack master won the master role and will still be the manager of this stack. All the units of the losing stack master will be reset and join back the stack later.

Recommended Action Please refer to the power consideration sequences of a stack to prevent two stack masters in the same stack at the same time.


Severity Level 5 Error Message Management unit conflict was detected and this unit has lost the

manager election. All the units in this stack will reset and join the winner Stack Manager %x:%x:%x:%x:%x:%x.

Explanation Two stack masters in a stack, the current stack master loses the master role and all the units belonging to this stack will be reset and join the winner stack master later.

Recommended Action Please refer to the power consideration sequences of a stack to prevent two stack masters in the same stack at the same time.

Severity Level 0 Error Message Auto upgrade reset unit <unit-id> Explanation The FW of this unit is auto-upgrade complete by the stack

master and stack master reset this unit. Recommended Action A notification message for user that this unit is reset by the stack

master due to the auto image upgrade complete.

Severity Level 5 Error Message No Potential unit to configure as Standby when unit <unit-id>

joined Explanation No other unit to be configured as the standby unit. This unit

should be the only one stack member in the stack. Recommended Action No standby unit is used in current stack.

Severity Level 5 Error Message No Potential unit to configure as Standby when unit <unit-id> leftExplanation No other unit to be configured as the standby unit. This unit

should be the only one stack member in the stack. Recommended Action No standby unit is used in current stack.

Severity Level 5 Error Message Admin configured standby %d left the stack Explanation The configured standby unit is left the stack. Recommended Action Checking if this unit has been removed from the stack.

Severity Level 3 Error Message This unit <unit-id> does not have admin management preference

enabled Explanation This unit has been configured to be a non-management unit. It

can’t be selected as a standby unit. Recommended Action To enable the admin management preference if you want this

unit to be a standby unit.


Severity Level 6 Error Message Stack Firmware Synchronization Start for unit %d Explanation The Firmware synchronization is started for a unit Recommended Action DO NOT remove this unit while the Firmware updating

Severity Level 2 Error Message Stack Firmware Synchronization Failed for unit <unit-id>. Use

archive copy-sw command to synchronize the image manually. Explanation The Firmware synchronization is failed for a unit Recommended Action Please use archive copy-sw command to synchronize the image

manually.

Severity Level 6 Error Message Stack Firmware Synchronization Finished for unit <unit-id> Explanation The Firmware synchronization is finished Recommended Action The Firmware synchronization for this unit is finished

Severity Level 6 Error Message Stack MAC address is changed to that of current stack master. Explanation The stack MAC address is changed to the one of current stack

master. Recommended Action To use persistent stack MAC address, use ‘stack-mac persistent

timer 0’ command.

Severity Level 6 Error Message Stack MAC Address owner rejoins the stack, stopping stack-mac

persistent timer Explanation The stack-mac persistent timer is stopped when the stack MAC

address owner rejoins the stack. The stack MAC address is kept using without changing to the one of current stack master.

Recommended Action Checking if the stack MAC address is remaining unchanged.


2.30 ISMIC Messages

Severity Level 6 Error Message Can't set the RTC from MMB while SNTP is configured in

system. Explanation Connection blade is using SNTP, the RTC set from MMB will be

ignored. Recommended Action If you want the RTC is snyc. from MMB, disabling the SNTP

client.

Severity Level 6 Error Message PowerConsumption request cmd error: <0x%x> Explanation Power consumption request value should be 0xffff from MMB. Recommended Action Checking MMB why to issue a undefined request value.

Severity Level 6 Error Message RTC sync. request from MMB. Explanation RTC sync. request value is received. Recommended Action

Severity Level 6 Error Message Can't set the RTC value less than 1970. Explanation The RTC value should be greater than year 1970. Recommended Action Checking the RTC value on MMB

Severity Level 6 Error Message Recv e-Keying of JS1 request from MMB Explanation e-Kaying of JS1 request is received. Recommended Action

Severity Level 6 Error Message Recv e-Keying of JS2 request from MMB Explanation e-Kaying of JS2 request is received. Recommended Action

Severity Level 6 Error Message Recv extended e-Keying request from MMB Explanation Extended e-Keying request is received. Recommended Action


Severity Level 6 Error Message Can't change DHCP client identifier while DHCP client identifier

mode is not TEXT Explanation Can't change DHCP client identifier while DHCP client identifier

mode is not TEXT Recommended Action Change the DHCP identifier to use TEXT mode.

Severity Level 6 Error Message Internal stacking port (S1) is disabled by E-Keying on unit:

<unit-id> Explanation Internal stacking port (S1) is disabled by e-Keying on unit

<unit-id> Recommended Action Check the setting from the management blade of BX900 if the

internal stacking is disabled. If you want to stack two connection blade, enabling the internal stacking link is preferred.

2.31 Port Group Messages

Severity Level 6 Error Message Failed to set isolation mode of intIfNum <intIfNum> Explanation Can’t apply the isolation function for interface <intIfNum> while

interface is link up. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message portGrpsIntfChangeCallback: Received an interface event

callback while not in EXECUTE state. (event: <event>, state: <state>)

Explanation portGrps is not ready executed. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message portGrpsPortMirroringCheck: portGrpsMemberRemove: rc=<rc> Explanation Member be removed from port group failure. Recommended Action Send the log to your support agent to find the problem.


2.32 Uplink Set Messages

Severity Level 6 Error Message linkSetSave: Error on call to sysapiCfgFileWrite for config file

<linkSetConfig File Name> Explanation Failed saveing linkSetconfiguration. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message Critical Error!! intIfNum <intIfNum> is neither a active_port

member nor a backup_port member. Explanation The interface to be removed from a uplink set is neither a active

port nor backup port member. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message Add interface <intIfNum> to port-channel failed (group:

<uplinksetName>) Explanation The interface to be added to a uplink set is failed. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message Remove interface <intIfnum> from active_port failed (group:

<uplinksetName>) Explanation The interface to be remove from active port of a uplink set is

failed. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message Remove interface <intIfnum> from backup_port failed (group:

<uplinksetName>) Explanation The interface to be remove from backup port of a uplink set is

failed. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message Port-backup: Switching to the active port (intIfNum: <intIfNum>) Explanation Port backup function switch the traffic to active port. Recommended Action


Severity Level 6 Error Message linkSetApplyConfigData: Get Error Result <rc> in

usmDbDot3adCreateSet(), LAG_NAME=<lag name> Explanation Failed apply config. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message Adding <interface> to Active port-channel <id> (group: <id>) is

failed Explanation Failed too add interface to active port-channel. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message Adding <interface> to Backup port-channel <id> (group: <id>) is

failed Explanation Failed too add interface to backup port-channe. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message linkSetIntfChangeCallback: Received an interface event callback

while not in EXECUTE state. (event: <event>, state: <state>) Explanation linkset is not ready executed. Recommended Action Send the log to your support agent to find the problem.

Severity Level 6 Error Message Warring : The last member <slot>/<port> of active ports will be

removed! Explanation The last member of group will be removed from group. Recommended Action No recommended action, it just a warning message.

Severity Level 6 Error Message Warring : <slot>/<port> cannot be added to the default uplink set

because this set is full! Explanation Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message LinkSet <name> can't be released by module Explanation Failed to released linkset by another module. Recommended Action Send the log to your support agent to find the problem.

2.33 VLAN Port Group Messages

Severity Level 6 Error Message vportGrpsSave: Error on call to sysapiCfgFileWrite for config file

<vportGrps Config File Name>


Explanation Failed saveing vportGrps configuration. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message vportGrpsIntfChangeCallback: Received an interface event


Explanation vportGrps is not ready executed. Recommended Action Send the log to your support agent to find the problem.


2.34 Link State Messages

Severity Level 6 Error Message vportGrpsSave: Error on call to sysapiCfgFileWrite for config file

<vportGrps Config File Name> Explanation Failed saveing vportGrps configuration. Recommended Action The config file is corrupt and use the factory default intead

Severity Level 6 Error Message vportGrpsIntfChangeCallback: Received an interface event


Explanation vportGrps is not ready executed. Recommended Action Send the log to your support agent to find the problem.


2.35 Port Backup Messages

Severity Level 6 Error Message Port-Backup: Failback to the active port (intIfNum: <intIfNum>) Explanation Failback activating notify. Recommended Action No recommended action, it just a warning message.

Severity Level 6 Error Message Warring : Removing active/backup port, the Port-Backup group

<id> mode will be disabled. Explanation Recommended Action No recommended action, it just a warning message.

Severity Level 6 Error Message Port-backup: Stop failback timer on intIfNum <intIfNum> Explanation Interface <intIfNum> is link down again and system stop the

failback time of this interface. Recommended Action No recommended action, it just a warning message.


2.36 SFlow Messages

Severity Level 6 Error Message sFlowPduReceive: Failed to give msgQueue semaphore Explanation Failed to give msgQueue semaphore Recommended Action Semaphore lock

Severity Level 6 Error Message sFlowReceiverFlowSampleAdd: Failed to send out datagram Explanation Failed to send out datagram. Recommended Action Socket error

Severity Level 6 Error Message sFlowReceiverFlowSampleAdd: sample length is overshooting

max datagram size Explanation sample length is overshooting max datagram size Recommended Action Setting sample length

Severity Level 6 Error Message sFlowReceiverSampleAdd: data_format %u not supported Explanation data_format not supported Recommended Action Only support : SFLOW_FLOW_SAMPLE,

SFLOW_COUNTERS_SAMPLE

Severity Level 6 Error Message sFlowReceiverFlowSampleWrite: flow record type 1 not

supported Explanation flow record type not supported Recommended Action Packet headers are sampled


address get failed Explanation IPv4 agent address get failed Recommended Action Setting IPv4 address


address get failed Explanation IPv6 agent address get failed Recommended Action Setting IPv6 address

Severity Level 6 Error Message sFlowRcvrAddressSet: Failed to give msgQueue semaphore Explanation Failed to give msgQueue semaphore Recommended Action Semaphore lock


Severity Level 6 Error Message sFlowRcvrOnwerSet: Failed to give msgQueue semaphore Explanation Failed to give msgQueue semaphore Recommended Action Semaphore lock

Severity Level 6 Error Message sFlowFsPacketSamplingRateSet: Failed to give msgQueue

semaphore Explanation Failed to give msgQueue semaphore Recommended Action Semaphore lock

Severity Level 6 Error Message sFlowCpIntervalSet: Failed to give msgQueue semaphore Explanation Failed to give msgQueue semaphore Recommended Action Semaphore lock

Severity Level 6 Error Message sflowSave: Error on call to sysapiCfgFileWrite file Explanation Can’t save config file Recommended Action Check File system

Severity Level 6 Error Message sFlowApplyConfigData: Failed to apply global config Explanation Failed to apply global config Recommended Action Config file content wrong

Severity Level 1 Error Message Failure sending sFlow configurator init message. Explanation Send Message error Recommended Action System init error

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: Error allocating data for poller

AVL Tree Explanation Error allocating data for poller AVL Tree Recommended Action System init error

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: Error allocating data for sampler

AVL Tree Explanation Error allocating data for poller AVL Tree Recommended Action System init error

Severity Level 6 Error Message Error allocating buffers Explanation Error allocating Buffer pool Recommended Action Memory not enought

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: Falied to allocate memory for


Sflow timer buffers Explanation Error allocating Sflow timer buffers Recommended Action Memory not enought

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: App Timer Initialization Failed Explanation App Timer Initialization Failed Recommended Action System init error

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: Error allocating Handle List

Buffers Explanation Error allocating Handle List Buffers Recommended Action Memory not enought

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: Unable to create timer handle listExplanation Unable to create timer handle list Recommended Action System init error

Severity Level 6 Error Message sFlowCnfgrInitPhase1Process: Unable to create sockets Explanation Unable to create sockets Recommended Action System init error

Severity Level 6 Error Message sflowCnfgrInitPhase2Process: Unable to register with NIM Explanation Unable to register with NIM Recommended Action System init error

Severity Level 1 Error Message Failure creating sFlow rw lock Explanation Unable to register with NIM Recommended Action Read/write lock to protect component data since processing

occurs on multiple threads (sFlow thread, UI thread, dot1q, etc)

Severity Level 1 Error Message Failure creating sFlow queue semaphore Explanation Failure creating sFlow queue semaphore Recommended Action System init error

Severity Level 1 Error Message sFlow unable to create event queue Explanation sFlow unable to create event queue Recommended Action System init error

Severity Level 1 Error Message sFlow unable to create packet queue Explanation sFlow unable to create packet queue Recommended Action System init error


Severity Level 1 Error Message ERROR: Unable to create sFlow thread Explanation Unable to create sFlow thread Recommended Action System init error

Severity Level 1 Error Message Unable to initialize sFlowTask Explanation Unable to initialize sFlowTask Recommended Action System init error

Severity Level 6 Error Message sFlowTask(): Internal event msg receive failed Explanation event msg receive failed Recommended Action System init error

Severity Level 6 Error Message sFlowTask(): invalid message type Explanation invalid message type Recommended Action System init error

Severity Level 6 Error Message sFlowIntfChangeCallback: Received an interface change

callback while not ready to receive it Explanation Received an interface change callback while not ready to

receive it Recommended Action System init error

Severity Level 6 Error Message sFlowIntfChangeCallback: Failed to give msgQueue semaphore Explanation Failed to give msgQueue semaphore Recommended Action Semaphore lock

Severity Level 6 Error Message sflowTimerExpiryHdlr(): Sflow timer tick send failed Explanation Sflow timer tick send failed Recommended Action Timer error

Severity Level 6 Error Message sflowTimerExpiryHdlr: MsgQSema give failed Explanation MsgQSema give failed Recommended Action Semaphore lock

Severity Level 6 Error Message sFlowIntfAttach: could not enable the sampler object for

interface .The configuration of new stack member ports added failed.

Explanation could not enable the sampler object for interface Recommended Action port init error

Severity Level 6 Error Message sFlowIntfAttach: could not enable the poller object for


interface .The configuration of new stack member ports added failed.

Explanation could not enable the sampler object for interface Recommended Action port init error

Severity Level 6 Error Message sFlowIntfDetach: could not disable the sampler object for

interface Explanation could not disable the sampler object for interface Recommended Action port init error

Severity Level 6 Error Message sFlowIntfDetach: could not disable the poller object for interface Explanation could not disable the poller object for interface Recommended Action port init error

Severity Level 6 Error Message sFlowIntfDelete: could not delete the sampler object for interfaceExplanation could not delete the sampler object for interface Recommended Action port init error

Severity Level 6 Error Message sFlowIntfDelete: could not delete the poller object for interface Explanation could not delete the poller object for interface Recommended Action port init error

Severity Level 6 Error Message sFlowReceiverAddressApply: Failed to set one or more sampler

objects Explanation Failed to set one or more sampler objects Recommended Action sflow init error

Severity Level 6 Error Message sFlowReceiverAddressApply: Failed to set one or more poller

objects Explanation Failed to set one or more poller objects Recommended Action sflow init error

Severity Level 6 Error Message sFlowPollerIntervalApply: Failed to enable poller for dsIndex %u

instance Explanation Failed to enable poller Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplerRateApply: Failed to enable sampler for dsIndex

%u instance %u Explanation Failed to enable sampler Recommended Action sflow init error

Severity Level 6


Error Message sFlowTimerTickProcess: Failed to flush the receiver data Explanation Failed to flush the receiver data Recommended Action socket error

Severity Level 6 Error Message sFlowSamplerPollerInstancesCleanup: could not delete poller

for dsIndex %u instance %u Explanation could not delete poller Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplerPollerInstancesCleanup: could not delete sampler

for dsIndex %u instance %u Explanation could not delete sampler Recommended Action sflow init error

Severity Level 6 Error Message sFlowPollerAdd: failed to add poller object for dsIndex %u

instance %u Explanation failed to add poller objec Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplerAdd: failed to add sampler object for dsIndex %u

instance %u Explanation failed to add sampler object Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplerAdd: failed to add sampler object for dsIndex %u

instance %u Explanation failed to add sampler object Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplerOperModeSet: Failed to set sampling rate in

hardware for dsIndex %u.Sampling rate set failed in driver Explanation Sampling rate set failed in driver Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplerOperModeSet: Failed to read sampling rate from

hardware for dsIndex %u Explanation Failed to read sampling rate Recommended Action sflow init error

Severity Level 6 Error Message sFlowPollerOperModeSet: Timer start failed for dsIndex %u

instance %u Explanation Timer start failed Recommended Action sflow init error


Severity Level 6 Error Message sFlowPollerOperModeSet: Timer stop failed for dsIndex %u

instance %u Explanation Timer stop failed Recommended Action sflow init error

Severity Level 6 Error Message sFlowSamplingRateThrottle: Failed to modify sampling rate for

dsIndex %d instance %d Explanation Failed to modify sampling rate Recommended Action sflow init error

Severity Level 6 Error Message sFlowIntfCanBeEnabled: nimIntfQuery failed for intf %s Explanation nimIntfQuery failed Recommended Action port init error

Severity Level 6 Error Message sFlowPollerTimerStart: Timer could not be updated for dsIndex

%u instance %u interval %u Explanation Timer could not be updated Recommended Action timer init error

Severity Level 6 Error Message sFlowPollerTimerStart: Could not get the handle node to store

the expiry timer data. Timer list is full and no more new timer creations are possible

Explanation Timer list is full and no more new timer creations are possible Recommended Action timer init error

Severity Level 6 Error Message sFlowPollerTimerStart: Could not start poller timer for dsIndex

%u instance %u Explanation Could not start poller timer Recommended Action timer init error

Severity Level 6 Error Message sFlowPollerTimerStop: Failed to stop poller timer for dsIndex %u

instance %u Explanation Failed to stop poller timer Recommended Action timer init error


Severity Level 6 Error Message sFlowPollerTimerExpiry: Failed to retrieve handle Explanation Failed to retrieve handle Recommended Action timer init error

Severity Level 6 Error Message sFlowPollerTimerExpiry: Failed to restart poller timer for dsIndex

%u Explanation Failed to restart poller timer Recommended Action timer init error


2.37 Err-Disable Recovery

Severity Level 6 Error Message <Cause> error detected on <intIfNum>, putting <intIfNum> to

err-disable state." Explanation There is an error detected on <intIfNum> by <Cause> and

<intIfNum> is shutdown. Recommended Action Check and remove the cause. Use ‘no shutdown’ to enable

<intIfNum>. Or use errdisable recovery timer to enable it.

Severity Level 6 Error Message <intIfNum> is binging out of err-disable state. Explanation <intIfNum> is enabled again by the errdisable recovery timer. Recommended Action Check and remove the cause.

2.38 MAC Bucket Overflow

Severity Level 6 Error Message MAC Address Bucket OverFlow entry learned on <intIfNum>

(MAC : <MacAddr>, VLAN : <vlanId>). Explanation The MAC address <MACAddr> has bucket overflow, and it is

learned by EHM on <intIfNum>. Recommended Action The MAC address bucket overflowed and can’t be inserted into

the L2 table.

Severity Level 6 Error Message Maximum MAC Address Bucket OverFlow entry reached on

<intIfNum> (MAC : <MacAddr>, VLAN : <vlanId>)." Explanation The maximum support overflowed MAC address is reached. The

MAC address <MacAddr> can’t be learned by EHM on <intIfNum>.

Recommended Action The MAC address bucket overflowed and can’t be inserted into the L2 table. The maximum support overflowed MAC address is 25 per interface. Suggest to move this MAC address to other chasiss.


2.39 Pin Group

Severity Level 4 Error Message "Applying EHM rules for downlink port <interfaceName> is failed

(<code>) w/ pinned interface <interfaceName>", Explanation Applying EHM rules of downlink port (such as unknown unicast

forward to pinned interface) is not able to be set to the hardware.Recommended Action Provide output of the ‘show tech-support’ to your support to get

assisant.

Severity Level 6 Error Message "Fail to initialize the egress mask for interface <interfaceName>" Explanation The egress mask of uplink port is not able to be set to the

hardware. Recommended Action Provide output of the ‘show tech-support’ to your support to get

assisant.


3 CLI Error Messages

3.1 Management

3.1.1 Configuration

This section contains the Configuration General Syntax Error messages.

Error Message Invalid IP address. IP address should be in a.b.c.d format where

range for a, b, c, and d is 1 - 255. Explanation User input an IP address with wrong format. Recommended Action IP address should be in a.b.c.d format where range for a, b, c,

and d is 1 - 255.

Error Message Mask must have contiguous ones. Explanation User input an IP subnet mask that does not have contiguous

ones in binary. For example, 255.255.255.129, the decimal 129 is 10000001 in binary, it’s not a contiguous ones number.

Recommended Action Use the correct IP subnet mask format. The subnet mask should have contiguous ones in binary. For example, 255.255.255.128 or 255.255.255.192 or 255.255.255.224.

Error Message Subnet mask must have contiguous ones and be no longer than

30 bits. Explanation User input an IP subnet mask tht does not have contiguous ones

in binary or the mask has more than 30 ones in binary. a. 255.255.255.129, the decimal 129 is 10000001 in binary, it’s

not a contiguous ones number. b. 255.255.255.254 in binary has 31 ones.

Recommended Action a. The subnet mask should have contiguous ones in binary. For example, 255.255.255.128 or 255.255.255.192 or 255.255.255.224.

b. The total ones of subnet should not exceed 30 bits. For example, 255.255.255.252 has 30 contiguous ones.

Error Message Incorrect input! netmask must have contiguous ones. Explanation User input an IP subnet mask tht does not have contiguous ones

in binary. For example, 255.255.255.129, the decimal 129 is 10000001 in binary, it’s not a contiguous ones number.



Error Message User Input Error: Invalid IP Address. Explanation The input IP address is invalid format or reserved IP address. Recommended Action Use the correct IP address for this function.

Error Message Incorrect input! Use 'oem {europe | japan | quanta}' Explanation Incomplete command for this function. Recommended Action Use 'oem {europe | japan | quanta}'

Error Message Incorrect input! Use 'show interface counters { <unit/slot/port> |

all | detailed }'. Explanation Incomplete command for this function. Recommended Action Use 'show interface counters { <unit/slot/port> | all | detailed }'.

Error Message Incorrect input! Use 'show interface counter detailed

{<unit/slot/port> | switchport}'. Explanation Incomplete command for this function. Recommended Action Use 'show interface counter detailed {<unit/slot/port> |

switchport}'.


This section contains the Configuration In-band management messages.

Error Message Incorrect input! Use 'ip default-gateway <gateway>’. Explanation Incomplete command for this function. Recommended Action Use 'ip default-gateway <gateway>'.

Error Message IP address and netmask must be set first. Explanation User attempt to set default-gateway before configuring

management IP address. Recommended Action Set the management IP address & netmask first.

Error Message IP Address/Netmask entered conflicts with the configured IP

Address/Netmask of the oob mgmt interface. Explanation User attempt to set In-band management IP address that is the

same subnet with OOB management interface. Recommended Action Use different subnet to configure In-band & Out-band

management IP address.

Error Message Incorrect input! <gateway> must be a valid IP Address. Explanation User input a invalid IP address for gateway. Recommended Action Use the valid IP address for gateway.

Error Message Incorrect input! Use 'ip address <ipaddr> <netmask>'. Explanation Incomplete command for this function. Recommended Action Use 'ip address <ipaddr> <netmask>'.

Error Message Incorrect input! Use 'ip address protocol {none | bootp | dhcp}'. Explanation Incomplete command for this function. Recommended Action Use 'ip address protocol {none | bootp | dhcp}'.

Error Message Incorrect input! Use 'ipv6 address protocol {dhcp6 | none}'. Explanation Incomplete command for this function. Recommended Action Use 'ipv6 address protocol {dhcp6 | none}'.


This section contains the Configuration Out-Band Mgmt messages. Error Message Incorrect input! Use 'oob ip <ipaddr> <netmask>'. Explanation Incomplete command for this function. Recommended Action Use 'oob ip <ipaddr> <netmask>'.

Error Message Incorrect input! 'netmask must have contiguous ones'. Explanation User input incorrect form of netmask. Recommended Action Configure the netmask in the form of <a.b.c.d> .

Error Message Incorrect input! Use 'oob protocol {none [dhcp6] | bootp | dhcp |

dhcp6}'. Explanation Incomplete command for this function. Recommended Action Use 'oob protocol {none [dhcp6] | bootp | dhcp | dhcp6}'.

Error Message Incorrect input! Use 'oob gateway <gateway>'. Explanation Incomplete command for this function. Recommended Action Use 'oob gateway <gateway>'.

Error Message Could not configure gateway. Explanation Only one gateway could be set in a switch. Recommended Action Please check if the gateway has been set by DHCP/Bootp.

Error Message IP address and gateway do not reside on the same subnet! Explanation User input invalid IP address for oob gateway. Recommended Action OOB IP address and OOB gateway should be on the same

subnet.

Error Message oob mgmt interface protocol must be none to set IP address. Explanation User can’t configure a fixed IP address while Out-of-band

management interface is set to get the IP address via DHCP/Bootp protocol.

Recommended Action Change the protocol to none before configuring IP address.

Error Message Only one interface can run DHCP or Bootp. Configure network

protocol to none. Explanation User attempt to set oob protocol to DHCP or Bootp, but the IP

interface has already set to DHCP or Bootp. Recommended Action Change the protocol to none or change ip interface protocol to

none.


This section contains the Configuration Telnet Session messages. Error Message Incorrect input! Use 'maxsessions <0-5>'. Explanation Incomplete command for this function. Recommended Action Use 'maxsessions <0-5>'.

Error Message Incorrect input! Use 'exec-timeout <1-160>'. Explanation Incomplete command for this function. Recommended Action Use 'exec-timeout <1-160>'.

Error Message Incorrect input! Use 'password-threshold <0-120>'. Explanation Incomplete command for this function. Recommended Action Use 'password-threshold <0-120>'.

Error Message Incorrect input!! Use 'terminal-length <10-100>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘terminal-length <10-100>'.

Error Message Error : Unable to create remote connection. Explanation User attempt to telent a host from device, but fail to connect. Recommended Action Make sure the IP configuration of device is correct, and the

Telnet service of target host is alive.

Error Message Incorrect input! Use 'telnet <host> [port] [debug] [line] [echo]'. Explanation Incomplete command for this function. Recommended Action Use 'telnet <host> [port] [debug] [line] [echo]'.


This section contains the Configuration Telnet Client Config messages. Error Message Incorrect input! Use 'telnet maxsessions <0-5>'. Explanation Incomplete command for this function. Recommended Action Use 'telnet maxsessions <0-5>'.

Error Message Incorrect input! Use 'telnet exec-timeout <1-160>'. Explanation Incomplete command for this function. Recommended Action Use 'telnet exec-timeout <1-160>'.


This section contains the Configuration SSH Client Session messages.

Error Message Incorrect input! Use 'ssh <ip-address|hostname> <username>

[protocol <protocollevel> port <1-65535>]'. Explanation Incomplete command for this function. Recommended Action Use 'ssh <ip-address|hostname> <username> [protocol

<protocollevel> port <1-65535>]'.


This section contains the Configuration SSH Client Config messages. Error Message Incorrect input! Use 'sshc maxsessions <0-5>'. Explanation Incomplete command for this function. Recommended Action Use 'sshc maxsessions <0-5>'.

Error Message Incorrect input! Use 'sshc exec-timeout <1-160>'. Explanation Incomplete command for this function. Recommended Action Use 'sshc exec-timeout <1-160>'.


This section contains the Configuration Serial Port messages. Error Message Incorrect input! Use 'baudrate

{1200|2400|4800|9600|19200|38400|57600|115200}'. Explanation Incomplete command for this function. Recommended Action Use 'baudrate

{1200|2400|4800|9600|19200|38400|57600|115200}'.

Error Message Incorrect input! Use 'exec-timeout <0-160>'. Explanation Incomplete command for this function. Recommended Action Use 'exec-timeout <0-160>'.

Error Message Incorrect input! Use 'password-threshold <0-120>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘password-threshold <0-120>'

Error Message Incorrect input! Use 'silent-time <0-65535>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘silent-time <0-65535>'

Error Message Incorrect input!! Use 'terminal-length <10-100>'. Explanation Incomplete command for this function. Recommended Action Use 'terminal-length <10-100>'.

Error Message Incorrect input! Use 'login local'. Explanation Incomplete command for this function. Recommended Action Use 'login local'.


This section contains the Configuration HTTP Config messages.

Error Message Incorrect input! Use 'ip http port <1-65535>.' Explanation Incomplete command for this function. Recommended Action Use 'ip http port <1-65535>.'

Error Message Incorrect input! Invaild HTTP Port Number. HTTP Port Set

Failed! Explanation Port number has been configured for other protocol. Recommended Action Please configure an unsused port number for HTTP. (Port

number 22 and 23 has been used by SSH & Telnet in default.)

Error Message Incorrect input! Use 'ip http session hard-timeout <0-168>'. Explanation Incomplete command for this function. Recommended Action Use 'ip http session hard-timeout <0-168>'.

Error Message Incorrect input! Use 'ip http session maxsessions <0-16>'. Explanation Incomplete command for this function. Recommended Action Use 'ip http session maxsessions <0-16>'.

Error Message Incorrect input! Use 'ip http session soft-timeout <0-60>'. Explanation Incomplete command for this function. Recommended Action Use 'ip http session soft-timeout <0-60>'.


This section contains the Configuration DDNS Config messages. Error Message Incorrect input! Use 'ddns dhs <username> <password> <host>

[<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns dhs <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use 'no ddns dhs <username> <password>

<host> [<address>]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns dhs <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use 'ddns dhs <username> <password> <host>'.Explanation The input character of <username> or <password> or <host>

has exceeded the limit. Recommended Action The maximum legth of <username>/<password> is 32

characters. And the maximum length of <host> is 44 characters.

Error Message Incorrect input! Use 'ddns dhs <username> <password> <host>

<address>'. Explanation The input character of <username> or <password> or <host>




<host>'. Explanation The input character of <username> or <password> or <host>




<host> <address>'. Explanation The input character of <username> or <password> or <host>




Error Message Error! Unable to set ddns dhs command. Explanation User try to remove a dhs DDNS setting, but the system does not

have this DDNS record. Recommended Action Use the correct dhs DDNS setting for this function.

Error Message Incorrect input! Use 'ddns dyndns <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns dyndns <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use 'no ddns dyndns <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns dyndns <username>

<password> <host> [<address>]'

Error Message Incorrect input! Use 'ddns dyndns <username> <password>




Error Message Incorrect input! Use 'no ddns dyndns <username> <password>


has exceed the limit. Recommended Action The maximum length of <username>/<password> is 32


Error Message Error! Unable to set ddns dyndns command. Explanation User try to remove a dyndns DDNS setting, but the system does

not have this DDNS record. Recommended Action Use the corrct dyndns DDNS setting for this function.

Error Message Incorrect input! Use 'ddns dyns <username> <password> <host>

[<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns dyns <username> <password>

<host> [<address>]'


Error Message Incorrect input! Use 'no ddns dyns <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns dyns <username>


Error Message Incorrect input! Use 'ddns dyns <username> <password>








Error Message Incorrect input! Use 'ddns dyns <username> <password> <host>








Error Message Error! Unable to set ddns dyns command. Explanation User try to remove a dyns DDNS setting, but the system does

not have this DDNS record. Recommended Action Use the corrct dyns DDNS setting for this function.


Error Message Incorrect input! Use 'ddns easydns <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns easydns <username>


Error Message Incorrect input! Use 'no ddns easydns <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns easydns <username>



















Error Message Error! Unable to set ddns easydns command. Explanation User try to remove a easydns DDNS setting, but the system

does not have this DDNS record. Recommended Action Use the corrct easydns DDNS setting for this function.

Error Message Incorrect input! Use 'ddns ods <username> <password> <host>

[<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns ods <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use 'no ddns ods <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns ods <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use ‚ddns ods <username> <password> <host>'.Explanation The input character of <username> or <password> or <host>







Error Message Incorrect input! Use ' ddns ods <username> <password> <host>









Error Message Error! Unable to set ddns ods command. Explanation User try to remove a ods DDNS setting, but the system does not

have this DDNS record. Recommended Action Use the corrct ods DDNS setting for this function.

Error Message Incorrect input! Use 'ddns zoneedit <username> <password>

<host> [<address>]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns zoneedit <username>


Error Message Incorrect input! Use 'no ddns zoneedit <username> <password>

<host> [<address>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns zoneedit <username>











<host> <address>' Explanation The input character of <username> or <password> or <host>








Error Message Error! Unable to set ddns zoneedit command. Explanation User try to remove a zoneedit DDNS setting, but the system

does not have this DDNS record. Recommended Action Use the corrct zoneedit DDNS setting for this function.

Error Message Incorrect input! Use 'ddns tzo <username> <password> <host>

[<address>]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘ddns tzo <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use 'no ddns tzo <username> <password>

<host> [<address>]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ddns tzo <username> <password>

<host> [<address>]'

Error Message Incorrect input! Use 'ddns tzo <username> <password> <host>'. Explanation The input character of <username> or <password> or <host>







Error Message Incorrect input! Use 'ddns tzo <username> <password> <host>









Error Message Error! Unable to set ddns tzo command. Explanation User try to remove a tzo DDNS setting, but the system does not

have this DDNS record. Recommended Action Use the corrct tzo DDNS setting for this function.

Error Message Invalid IP Address! Explanation User input a reserved IP address. For example 127.0.0.1 ,

255.1.1.1 or multicast IP address. Recommended Action Use the correct IP address for this function.

Error Message Incorrect input! Use 'show ddns'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show ddns | begin <LINE>'

Use complete command ‘show ddns | exclude <LINE>’ Use complete command ‘show ddns | include <LINE>’


This section contains the Hostname messages. Error Message Incorrect input! Use 'hostname <hostname>'. Explanation Incomplete command for this function. Recommended Action Use 'hostname <hostname>'.

Error Message Incorrect input! Maximum allowed length is 32 characters. Explanation User input a hostname over 32 characters. Recommended Action Maximum allowed length is 32 characters.


3.1.2 System Utilities

This section contains the Traceroute messages. Error Message Incorrect input! Invalid IP Address or Host Name Size. Explanation Enter more than 65 characters Recommended Action Use complete command ‘traceroute <hostname>.’

The maximum length of host name is 63 characters.

Error Message Incorrect input! Invalid Host Name. Explanation Enter more than 64 characters Recommended Action Use complete command ‘traceroute <hostname>.’

The maximum length of host name is 63 characters.

Error Message Incorrect input! Invalid IP address. IP address should be in

a.b.c.d format where range for a, b, c, and d is 1 - 255. Explanation The input IP address is invalid. Recommended Action Use the correct IP address format.

Error Message Incorrect input! Use 'traceroute {<ipaddr|hostname> | ipv6

<ipv6-address | hostname>} [initTtl <initTtl>] [maxTtl <maxTtl>] [interval <interval>] [count <count>]'.

Explanation Incomplete command for this function. Recommended Action Use complete command ‘traceroute <ipaddr|hostname>.’


This section contains the Ping messages.

Error Message Incorrect input! Use 'ping {<host> {[count <count>] | [size

<size>]} | ipv6 {{<ipv6-address | hostname> [size <datagram-size>]} | {interface {oob | switchport} <link-local-address> [size <datagram-size>]}}}'.

Explanation Incomplete command for this function. Recommended Action Use 'ping {<host> {[count <count>] | [size <size>]} | ipv6

{{<ipv6-address | hostname> [size <datagram-size>]} | {interface {oob | switchport} <link-local-address> [size <datagram-size>]}}}'.

Error Message Incorrect input! Invalid Host IP Address. Explanation The host IP address is invalid. Recommended Action Use the correct IP address.

Error Message Incorrect input! Invalid Host Name. (Range: 1-64 characters) Explanation Enter more than alphanumeric characters in length for host

name. Recommended Action Use complete command ‘ping <host>’. Host name range 1 to 64

characters in length.

Error Message Invalid Global Address. Explanation Wrong IPv6 Global address of ping function. Recommended Action User should use the correct IPv6 Global address for this

function, do not use the Link-Local or Multicast address.

Error Message Invalid Link-local address. Explanation Wrong IPv6 Link-Local address of ping function. Recommended Action User should use the correct IPv6 Link-Local address for this

function, do not use the Global or Multicast address.

Error Message Invalid length. Explanation The datagram size of IPv6 ping request has exceeded the range.Recommended Action The datagram size should be 48 – 2048.


Error Message Incorrect Input! Use 'ping ipv6 {{<ipv6-address | hostname> [size

<datagram-size>]} | {interface {oob | switchport} <link-local-address> [size <datagram-size>]}}'.

Explanation Incomplete command for this function. Recommended Action Use complete command ‘ping ipv6 {{<ipv6-address | hostname>

[size <datagram-size>]} | {interface {oob | switchport} <link-local-address> [size <datagram-size>]}}'.

Error Message Incorrect Input! Use 'ping ipv6 <ipv6-address | hostname> [size <datagram-size>]'.

Explanation Incomplete command for this function. Recommended Action Use complete command ‘ping ipv6 <ipv6-address | hostname>

[size <datagram-size>]'.

Error Message Incorrect Input! Use 'ping ipv6 interface {oob | switchport}

<link-local-address> [size <datagram-size>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ping ipv6 interface {oob | switchport}

<link-local-address> [size <datagram-size>]'.

Error Message Incorrect input! Invalid IPv6 address format. Explanation The IPv6 address format is not correct. Recommended Action Use the correct IPv6 address format for this function.

Error Message Invalid Input: Destination IPv6 address cannot be a Link Local

Address. Explanation User try to trace a Link-local IPv6 address, but the destination IP

should be Global Address. Recommended Action Use the Global IPv6 address for this function.

Error Message Invalid Input: Destination IPv6 address. Explanation User input the wrong IPv6 address. Recommended Action Use the complete Global IPv6 address for this function.

Error Message Incorrect input! Use 'show ipv6 traffic {oob | switchport}'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show ipv6 traffic {oob | switchport}'.


Error Message Incorrect input! Use 'clear ipv6 statistics {oob | switchport}'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘clear ipv6 statistics {oob | switchport}'.


3.1.3 File Management

This section contains the File Management messages. Error Message Incorrect input! Use 'delete <filename>'. Explanation User input incomplete command . Recommended Action Use 'delete <filename>'.

Error Message Incorrect input! File name must be of 30 characters or less. Explanation The length of input file name is exceeded the limilation. Recommended Action File name must be of 30 characters or less.

Error Message Incorrect input! Flie name could be alpha-numeric characters

and ~`@#$%^& ()_+-=;',.{}[] Explanation User input invalid characters for file name. Recommended Action Flie name could be alpha-numeric characters and ~`@#$%^&

()_+-=;',.{}[]

Error Message Incorrect input! Use boot-system {{boot-rom | config | opcode}

<filename> | mode {Switch | IBP} | auto-copy-sw}' Explanation User input invalid characters for file name. Recommended Action Use boot-system {{boot-rom | config | opcode} <filename> |

mode {Switch | IBP} | auto-copy-sw}'

Error Message Incorrect input! Use boot-system {{boot-rom | config | opcode}

<filename> | mode {Switch | IBP}}' Explanation User input invalid characters for file name. Recommended Action Use boot-system {{boot-rom | config | opcode} <filename> |

mode {Switch | IBP}}'



()_+-=;',.{}[]

Error Message Cannot find partition table entry! Explanation User attempt to download a file to switch but the file system is

full. Recommended Action The file system of switch can accept 2 Operation code & 10

Config file.




()_+-=;',.{}[]



()_+-=;',.{}[]

Error Message Failed to delete the Cli Banner Explanation User attempt to delete the CLI Banner, but there is no Banner in

switch. Recommended Action Make sure the CLI Banner is exist.

Error Message Incorrect input! Use 'script apply <scriptname.scr>'. Explanation User input incomplete command . Recommended Action Use 'script apply <scriptname.scr>'.

Error Message Incorrect input! Use 'script delete {all | <scriptname.scr>}'. Explanation User input incomplete command . Recommended Action Use 'script delete {all | <scriptname.scr>}'.

Error Message Incorrect input! Use 'script show <scriptname.scr>'. Explanation User input incomplete command . Recommended Action Use 'script show <scriptname.scr>'.

Error Message Incorrect input! Use 'copy { { {clibanner} | {script

<sourcefilename>} | errorlog | log | {image <filename>} {startup-config <source filename>}| traplog} <url> } | {<url> {clibanner} | {script <destfilename>} | {image <destfilename>} | {startup-config <filename>} } | {running-config startup-config [<filename>]}'

Explanation User input incomplete command. Recommended Action Use 'copy { { {clibanner} | {script <sourcefilename>} | errorlog |

log | {image <filename>} {startup-config <source filename>}| traplog} <url> } | {<url> {clibanner} | {script <destfilename>} | {image <destfilename>} | {startup-config <filename>} } | {running-config startup-config [<filename>]}'


Error Message Are you sure you want to save? (y/n) Explanation User attempt to download a file into switch. Recommended Action Press Y to save the file you download or press N to abort.

Error Message Invalid url specified! Use xmodem or

tftp://<ipaddress>/<filepath>/<fileName>. Explanation User input invalid IP address of tftp or ftp server. Recommended Action Make sure the IP address of tftp or ftp server is correct.


3.1.4 User Manangement

This section contains the User Accounts messages.

Error Message Incorrect input! Use 'username <username> { {passwd {0|7}

<password>} | nopasswd [privilege <0-15>]}'. Explanation User input incomplete command . Recommended Action Use 'username <username> { {passwd {0|7} <password>} |

nopasswd [privilege <0-15>]}'.

Error Message Error: Characters in the user name must be alphanumeric and

can contain dashes or underscores. Explanation User input a user name with non-alphanumeric characters. Recommended Action Use alphanumeric and dashes or underscores for user name.

Error Message Too many users, delete one first! Explanation User create a new user name when the table is full. Recommended Action Maximum 6 users can be created, please delete one first.

Error Message Cannot delete the admin user! Explanation User attempt to delete the username “admin”, it’s a default

setting can NOT be deleted. Recommended Action Correct the user name you want to delete.

Error Message Invalid password. User password length must be minimum

password length to 64 characters in length Explanation User input a invalid password length. Recommended Action User password length should be less then 64 and larger then

configured minimum length.

Error Message User privilege level must be 0 to 15 Explanation User input a invalid privilege level Recommended Action User should enter privilege level and the range is 0 to 15

Error Message Error!! Could not set prvilege level for this user. Explanation User change admin user’s privilege level Recommended Action User could not chnge the privilege level of admin user account

Error Message Incorrect input!! Use 'enable secret level <1-15> {0|7}

<password>'.


Explanation User input incomplete command. Recommended Action Use 'enable secret level <1-15> {0|7}

Error Message Incorrect input! Use 'enable passwd {0|7} <password>'. Explanation User input incomplete command. Recommended Action Use 'enable passwd {0|7} <password>'.

Error Message Incorrect input! Use 'username snmpv3 authentication

<username> {none|md5|sha}'. Explanation User input incomplete command. Recommended Action Use 'username snmpv3 authentication <username>

{none|md5|sha}'.

Error Message Incorrect input! Use 'no username snmpv3 authentication

<username>'. Explanation User input incomplete command. Recommended Action Use 'no username snmpv3 authentication <username>'.

Error Message Incorrect input! Use 'username snmpv3 encryption <username>

{none| {des {0|7} <key>} }' Explanation User input incomplete command. Recommended Action Use 'username snmpv3 encryption <username> {none| {des

{0|7} <key>} }'

Error Message Incorrect input! Use 'no username snmpv3 encryption

<username>'. Explanation User input incomplete command. Recommended Action Use 'no username snmpv3 encryption <username>'.

Error Message Incorrect input! Use 'no username snmpv3 encryption

<username>'. Explanation User input incomplete command. Recommended Action Use 'no username snmpv3 encryption <username>'.


This section contains the Authorization List Config messages. Error Message Incorrect input! Use 'show authorization users <listname>' Explanation User input incomplete command . Recommended Action Use 'show authorization users <listname>'

Error Message No Users exist for this Authorization Login List. Explanation There is no users belong to this Authorization Login List. Recommended Action Create user for this Authorization Login List first.

Error Message Incorrect input! Use 'authorization login <listname> [Option1 [

Option2 [ Option3 ]]]'. Explanation User input incomplete command . Recommended Action Use 'authorization login <listname> [Option1 [ Option2 [ Option3

]]]'.

Error Message Incorrect input! Use 'no authorization login <listname>'. Explanation User input incomplete command . Recommended Action Use 'no authorization login <listname>'.

Error Message Invalid authorization method. Explanation User input invalid authentication method for authorization login

list. Recommended Action Enter local/radius/reject/tacacs/ldap method for authorization

login list.

Error Message List name must contain alphanumeric characters only. Explanation User attempt to create an authorization login list with non-

alphanumeric characters. Recommended Action Use alphanumeric characters for authorization login list name.

Error Message Invalid Authorization Login List Name. Explanation User attempt to delete or assign a non-exist authorization login

list. Recommended Action Make sure the Authorization Login List Name exist or not.


Error Message The Authorization Login List has users assigned to it and

therefore cannot be deleted. Explanation User attempt to delete an authorization login list that has users

assigned to it. Recommended Action Remove users belong to the Authorization Login List before

deleting the List.

Error Message The default authorization list cannot be deleted. Explanation User attempt to delete the default authorization list. Recommended Action The default authorization list cannot be deleted ,make sure what

list you want to delete.

Error Message Could not create authorization login list. Name already exist! Explanation User attempt to create an authorization login list name that

already exist. Recommended Action Use other name for the authorization login list.

Error Message Could not create authorization login list. Maximum no. of login

lists reached! Explanation User attempt to create an authorization login list when table is

full. Recommended Action Maximum 10 authorization login list can be created.


This section contains the User Login messages. Error Message Incorrect input! Login list name must be 15 characters or less in

length. Explanation User attempt to create an authorization login list name with more

than 15 characters. Recommended Action Login list name must be 15 characters or less in length.

Error Message Incorrect input! Use 'username login <user> <listname>' Explanation User input incomplete command . Recommended Action Use 'username login <user> <listname>'

Error Message Incorrect input! Use 'username defaultlogin <listname>' Explanation User input incomplete command . Recommended Action Use 'username defaultlogin <listname>'

Error Message Invalid user name. User name can be up to 8 characters in

length. Explanation User input a user name over 8 characters. Recommended Action User name can be up to 8 characters in length.

Error Message Invalid User Name. Explanation User assign a non-exist user name for authorization list. Recommended Action Create the user name first.


3.1.5 Privilege Level

This section contains the privilege level

Error Message Incorrect input! Use 'privilege <mode> [all] reset <LINE>'. Explanation User input incomplete command . Recommended Action Use 'privilege <mode> [all] reset <LINE>

Error Message Error!! Command length should less the 128 characters. Explanation User input lenth of command is larger then 128 characters. Recommended Action User enter command length should be less then 128 characters

Error Message Error!! Could not reset this command. Explanation User input an not configured command. Recommended Action User should input configured privilege command.

Error Message Error!! Could not find this command. Explanation User input an not exist command. Recommended Action User should input exist command.

Error Message Error!! This command had configured already. Explanation User input a already configured command. Recommended Action User should input none configured privilege command.

Error Message Incorrect input! Use 'enable [<privilege level>]'. Explanation User input incompletely command Recommended Action Use 'enable [<privilege level>]

Error Message No password set. Explanation User higher access specified privilege level but the level did not

set enable secrect password. Recommended Action Set enable secrect password for specified privilege level.

Error Message Incorrect input! Use 'disable [<privilege level>]'. Explanation User input incompletely command Recommended Action Use 'disable [<privilege level>]

Error Message New privilege level must be less then current privilege level.


Explanation User execute to access higher privilege level Recommended Action This command can only access lower privilege level


3.1.6 Logging

This section contains the Logging messages. Error Message Incorrect input! Use 'logging syslog port <portid>'. Explanation User input incomplete command . Recommended Action Use 'logging syslog port <portid>'.

Error Message Incorrect input! Use 'logging host <ipAddr|ipv6Addr|name>

<addresstype> [<portid> [<severitylevel>]]'. Explanation User input incomplete command . Recommended Action Use 'logging host <ipAddr|ipv6Addr|name> <addresstype>

[<portid> [<severitylevel>]]'.

Error Message Incorrect input! Use 'logging host remove <hostindex>'. Explanation User input incomplete command . Recommended Action Use 'logging host remove <hostindex>'.

Error Message Incorrect input! Use 'logging host reconfigure <hostindex> host

<ipAddr|ipv6Addr|hostname> <addresstype>'. Explanation User input incomplete command . Recommended Action Use 'logging host reconfigure <hostindex> host

<ipAddr|ipv6Addr|hostname> <addresstype>'.

Error Message Incorrect input! Enter the port value in the range <1 - 65535>. Explanation User input invalid port value of logging host. Recommended Action Enter the port value in the range <1 - 65535>.

Error Message Incorrect input! Use ‘no logging host <hostindex>'. Explanation User input incomplete command. Recommended Action Use ‘no logging host <hostindex>'.

Error Message Incorrect input! Use 'logging host reconfigure <hostindex> port

<port>'. Explanation User input incomplete command. Recommended Action Use 'logging host reconfigure <hostindex> port <port>'.

Error Message Incorrect input! Use 'logging host reconfigure <hostindex>

severitylevel <level>'. Explanation User input incomplete command.


Recommended Action Use 'logging host reconfigure <hostindex> severitylevel <level>'.


3.1.7 SNMP

This section contains the SNMP messages. Error Message Incorrect input! Use 'snmp-server community {ro | rw}

<community-name>'. Explanation User input incomplete command. Recommended Action Use 'snmp-server community {ro | rw} <community-name>'.

Error Message Incorrect input! Use 'snmp-server community <name>'. Explanation User input incomplete command. Recommended Action Use 'snmp-server community <name>'.

Error Message Incorrect input! Use 'no snmp-server community <name>'. Explanation User input incomplete command. Recommended Action Use 'no snmp-server community <name>'.

Error Message Incorrect input! Use 'snmp-server community ipmask <ipmask>

<name>'. Explanation User input incomplete command. Recommended Action Use 'snmp-server community ipmask <ipmask> <name>'.

Error Message Incorrect input! Use 'no snmp-server community ipmask

<name>' Explanation User input incomplete command. Recommended Action Use 'snmp-server community ipmask <ipmask> <name>'.

Error Message Incorrect input! Use 'snmp-server community mode <name>'. Explanation User input incomplete command. Recommended Action Use 'snmp-server community mode <name>'.

Error Message Incorrect input! Use 'no snmp-server community mode <name>'. Explanation User input incomplete command. Recommended Action Use 'no snmp-server community mode <name>'.

Error Message Incorrect input! Use 'snmptrap snmpversion <name> <ipaddr>

<snmpversion>'. Explanation User input incomplete command. Recommended Action Use 'snmptrap snmpversion <name> <ipaddr> <snmpversion>'.


Error Message Incorrect input! Use 'no snmptrap <name> <ipaddr>'. Explanation User input incomplete command. Recommended Action Use 'no snmptrap <name> <ipaddr>'.

Error Message Incorrect input! Use 'snmptrap <name> <ipaddr> [snmpversion]

[<snmpversion>]' Explanation User input incomplete command. Recommended Action Use 'snmptrap <name> <ipaddr> [snmpversion]

[<snmpversion>]'

Error Message Incorrect input! Use 'snmptrap mode <name> <ipaddr>'. Explanation User input incomplete command. Recommended Action Use 'snmptrap mode <name> <ipaddr>'.

Error Message Incorrect input! Use 'no snmptrap mode <name> <ipaddr>'. Explanation User input incomplete command. Recommended Action Use 'no snmptrap mode <name> <ipaddr>'.

Error Message Incorrect input! Use 'snmptrap ipaddr <name> <ipaddrold>

<ipaddrnew>'. Explanation User input incomplete command. Recommended Action Use 'snmptrap ipaddr <name> <ipaddrold> <ipaddrnew>'.

Error Message Snmptrap already exists! Explanation User attempt to add an exist Snmptrap name. Recommended Action Use other name for the Snmptrap.

Error Message Snmptrap does not exist. Explanation User attempt to delete a non-exist Snmptrap name. Recommended Action Make sure the Snmptrap name is existed.

Error Message Incorrect input! Use 'snmp-server sysname <name>'. Name can

be up to 31 characters in length. Explanation User input incomplete command. Recommended Action Use 'snmp-server sysname <name>'. Name can be up to 31



Error Message Incorrect input! Maximum allowed length is 31 characters. Explanation User input over 31 characters. Recommended Action Maximum allowed length is 31 characters.

Error Message Incorrect input! Use 'snmp-server location <loc>'. Location can

be up to 31 characters in length. Explanation User input incomplete command. Recommended Action Use 'snmp-server location <loc>'. Location can be up to 31


Error Message Incorrect input! Use 'snmp-server contact <con>'. Contact value

can be up to 31 characters in length. Explanation User input incomplete command. Recommended Action Use 'snmp-server contact <con>'. Contact value can be up to 31


Error Message Incorrect input! Characters must be alphanumeric and can

contain dashes or underscores. Explanation User input non- alphanumeric characters. Recommended Action Use alphanumeric and dashes or underscores.


3.1.8 SNTP

This section contains the SNTP messages.

Error Message System clock modify failed. Explanation User attempt to modify calendar with invalid date or time format. Recommended Action Correct the date and time format.

DateTime <mm/dd/yyyy> format. (Month <1-12>. Day<1-31>. Year <2000-2099>). Time <hh:mm:ss> format.

Error Message Incorrect input! Use 'sntp client mode {broadcast | unicast}'. Explanation User input incomplete command. Recommended Action Use 'sntp client mode {broadcast | unicast}'.

Error Message Incorrect input! Use 'sntp client port <1 - 65535>'. Explanation User input incomplete command. Recommended Action Use 'sntp client port <1 - 65535>'.

Error Message SNTP Server with specificied address already exists. Explanation User create a SNTP Server with the IP address that had been

used for other SNTP Server. Recommended Action Correct the IP address of SNTP Server.

Error Message SNTP Server does not exist. Explanation User attempt to delete an non-exist SNTP server. Recommended Action Use correct IP address of SNTP Server which you want to

delete.

Error Message Could not add host. Maximum number of SNTP servers (3)

reached. Explanation User attempt to add a SNTP Server when table is full. Recommended Action Maximum 3 SNTP Server can be added.

Error Message Incorrect input! <ipaddress/domain-name> should be up to 64

characters. Explanation User input an IP address or domain-name over 64 characters. Recommended Action Use IP address or domain-name up to 64 characters.


Error Message Incorrect input! Use 'sntp server <ipaddress/domain-name>

<addresstype> [<priority> [<version> [<port>]]]'. Explanation User input incomplete command. Recommended Action Use 'sntp server <ipaddress/domain-name> <addresstype>

[<priority> [<version> [<port>]]]'.

Error Message Incorrect input! Use 'sntp broadcast client poll-interval <6 - 10>’ Explanation Incomplete command for this function. Recommended Action Use complete command ‘sntp broadcast client poll-interval <6 -

10>’

Error Message Incorrect input! Use 'sntp unicast client poll-interval <6 - 10>’ Explanation Incomplete command for this function. Recommended Action Use complete command ‘sntp unicast client poll-interval <6 -

10>’

Error Message Incorrect input! Use 'sntp unicast client poll-timeout <1 - 30>’ Explanation Incomplete command for this function. Recommended Action Use complete command ‘sntp unicast client poll-timeout <1 -

30>’

Error Message Could not set poll timeout value. Explanation The timeout value is out of the range. Recommended Action Correct command ‘sntp unicast client poll-timeout <1 - 30>’

Error Message Incorrect input! Use sntp unicast client poll-retry <0 - 10>’ Explanation Incomplete command for this function. Recommended Action Use complete command ‘sntp unicast client poll-retry <0 - 10>’

Error Message Could not set poll retry value. Explanation The retry value is out of the range. Recommended Action Correct command ‘sntp unicast client poll-retry <0 - 10>’

Error Message Incorrect input! Use 'sntp server

<ipaddress/ipv6address/domain-name> <addresstype> [<priority> [<version> [<port>]]]'.

Explanation Incomplete command for this function. Recommended Action Use complete command ‘sntp server

<ipaddress/ipv6address/domain-name> <addresstype> [<priority> [<version> [<port>]]]'.


Error Message Incorrect input! Use 'no sntp server

<ipaddress/ipv6address/domain-name> <addresstype>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no sntp server

<ipaddress/ipv6address/domain-name> <addresstype>'.

Error Message The address type should either 'dns' or 'ipv4 , ipv6’. Explanation Wrong address type for sntp server setting. Recommended Action The address type should either 'dns' or 'ipv4 , ipv6’.

Error Message Incorrect input! Use 'calendar set <mm/dd/yyyy> <hh:mm:ss>' Explanation User input incomplete command . Recommended Action Use 'calendar set <mm/dd/yyyy> <hh:mm:ss>'

Error Message Incorrect input! Use 'sntp clock timezone <name> <hours>

<minutes> [before-utc |after-utc]' Explanation User input incomplete command. Recommended Action Use 'sntp clock timezone <name> <hours> <minutes>

[before-utc |after-utc]'

Error Message SNTP time zone name must contain alphanumeric characters

only. Explanation User input non-alphanumeric characters for time zone name. Recommended Action Use alphanumeric characters for SNTP time zone name.


3.1.9 CDP

This section contains the CDP Config messages.

Error Message Incorrect input! Use 'cdp run all' Explanation User input incomplete command. Recommended Action Use 'cdp run all'

Error Message Incorrect input! Use 'no cdp run all' Explanation User input incomplete command. Recommended Action Use 'no cdp run all'

Error Message Incorrect input! Use 'cdp timer <5-254>' Explanation User input incomplete command. Recommended Action Use 'cdp timer <5-254>'

Error Message Incorrect input! Use 'cdp holdtime <10-255>' Explanation User input incomplete command. Recommended Action Use 'cdp holdtime <10-255>'

Error Message CDP is only supported on physical ports. Explanation User attempt to enable CDP on logical ports. Recommended Action CDP can only be enabled on physical ports.


3.1.10 UDLD

This section contains the UDLD messages. Error Message Incorrect input! Use 'show udld {<slot/port>}'. Explanation User input incomplete command . Recommended Action Use 'show udld {<slot/port>}'.

Error Message Error! UDLD can only be configured on physical interface. Explanation User attempt to configure/show udld on invalid interfaces. Recommended Action Make sure the interface is not port-channel interface.

Error Message Incorrect input! Use 'udld aggressive'. Explanation User input incomplete command . Recommended Action Use '’udld aggressive’.

Error Message Incorrect input! Use 'udld enable'. Explanation User input incomplete command . Recommended Action Use 'udld enable’.

Error Message Incorrect input! Use 'udld message time <7-90>'. Explanation User input incomplete command . Recommended Action Use 'udld message time <7-90>'.

Error Message Error! Input a value in the range of <7-90> seconds. Explanation User input a value out of range <7-90> seconds for udld

message time. Recommended Action Input a value in the range of <7-90>

Error Message Incorrect input! Use 'udld port aggressive'. Explanation User input incomplete command . Recommended Action Use '’udld port aggressive’.

Error Message Incorrect input! Use 'udld port'. Explanation User input incomplete command . Recommended Action Use 'udld port



3.1.11 LLDP

This section contains the LLDP messages. Error Message Incorrect input! Use 'show lldp interface {<slot/port> | all}'. Explanation User input incomplete command . Recommended Action Use 'show lldp interface {<slot/port> | all}'.

Error Message Incorrect input! Use 'show lldp statistics {<slot/port> | all}'. Explanation User input incomplete command . Recommended Action Use 'show lldp statistics {<slot/port> | all}'.

Error Message Incorrect input! Use 'show lldp remote-device { [detail]

<slot/port> | all}'. Explanation User input incomplete command . Recommended Action Use 'show lldp remote-device { [detail] <slot/port> | all}'.

Error Message Incorrect input! Use 'show lldp local-device { [detail] <slot/port> |

all}'. Explanation User input incomplete command . Recommended Action Use 'show lldp local-device { [detail] <slot/port> | all}'.

Error Message Error! Use "lldp transmit" to advertise local LLDP data on the

interface. Explanation User attempt to configure lldp transmit on invalid interfaces. Recommended Action Make sure the interface is not port-channel interface.

Error Message Error! Use "lldp receive" to receive remote LLDP data on the

interface. Explanation User attempt to configure lldp receive on invalid interfaces. Recommended Action Make sure the interface is not port-channel interface.

Error Message Error! Use "lldp transmit-mgmt" to transmit the LLDP

management address TLV on the interface. Explanation User attempt to configure lldp transmit-mgmt on invalid

interfaces. Recommended Action Make sure the interface is not port-channel interface.


Error Message Error! Use "lldp notification-interval <interval> " to limit how

frequently LLDP remote data change notifications are sent. Explanation User input incomplete command . Recommended Action Use "lldp notification-interval <interval> "

Error Message Error! Enter a value in the range <5 - 3600> seconds. Explanation User input an value out of range <5-3600> seconds for lldp

notification-interval. Recommended Action Enter a value in the range <5 - 3600> seconds.

Error Message Error! Use"lldp notification" to enable remote data change

notifications. Explanation User attempt to configure lldp notification on invalid interfaces. Recommended Action Make sure the interface is not port-channel interface.

Error Message Error! Use "lldp transmit-tlv [sys-desc] [sys-name] [sys-cap]

[port-desc] [org-spec]" to transmit LLDP optional TLV(s) on the interface.

Explanation User input incomplete command . Recommended Action Use "lldp transmit-tlv [sys-desc] [sys-name] [sys-cap] [port-desc]

[org-spec]" to transmit LLDP optional TLV(s) on the interface.

Error Message Error! Interface out of range. Explanation User attempt to configure LLDP transmit-tlv on invalid interfaces.Recommended Action Make sure the interface is not port-channel interface.

Error Message Error! Use "lldp timers [interval <transmit-interval>] [hold

<hold-multiplier>] [reinit <reinit-delay>]" to configure the LLDP global timer values.

Explanation User input incomplete command . Recommended Action Use "lldp timers [interval <transmit-interval>] [hold

<hold-multiplier>] [reinit <reinit-delay>]" to configure the LLDP global timer values.

Error Message Error! Enter a value in the range <2 - 10>. Explanation User input incomplete command or value out of range <2-10>. Recommended Action Enter a value in the range <2 - 10> for lldp timers hold.


Error Message Error! Enter a value in the range <1 - 32768> seconds. Explanation User input incomplete command or value out of range

<1-32768>. Recommended Action Enter a value in the range <1 - 32768> seconds for lldp timers

interval.

Error Message Error! Enter a value in the range <1 - 10> seconds. Explanation User input incomplete command or value out of range <1-10>. Recommended Action Enter a value in the range <1 - 10> seconds.

Error Message Error! Enter a value in the range <1 - 8192> seconds. Explanation User input incomplete command or value out of range <1-8192>.Recommended Action Enter a value in the range <1 - 8192> seconds for lldp tx deplay.

Error Message Error! Enter a value less than 0.25*TransmitInterval. Explanation User enter a an invalid value for lldp tx-delay Recommended Action Enter a value less then 0.25*TransmitInterval.


3.1.12 DHCP

This section contains the DHCP Client.

Error Message Incorrect input! Use 'ip dhcp client-identifier {text <text> | hex

<hex> }' Explanation User input incomplete command . Recommended Action Use 'ip dhcp client-identifier {text <text> | hex <hex> }'

Error Message Incorrect input! Use 'ip dhcp client-identifier hex

XX:XX:XX:XX:XX:XX' Explanation User input invalid format of hex value. Recommended Action Use 'ip dhcp client-identifier hex XX:XX:XX:XX:XX:XX'

Error Message Client identifier test must contain alphanumeric characters only. Explanation User input invalid value for Client identifier. Recommended Action Input text string. (Range: 1-32 characters)

Error Message Incorrect input! A text string. (Range: 1-32 characters) Explanation User input over 32 characters for Client identifier. Recommended Action Maximum 32 characters can be used for Client identifier.

Error Message Error! can't restart because the protocol of ipv6 dhcp6 client is

none. Explanation User try to restart IPv6 DHCP client function, but the IPv6 DHCP

client function doesn’t enable. Recommended Action Enable IPv6 DHCP client function on the switch interface.

(Config)#interface vlan 1 (if-vlan 1)#ipv6 address protocol dhcp6

Error Message Error! can't restart because the protocol of oob dhcp6 client is

none. Explanation User try to restart IPv6 DHCP client function, but the IPv6 DHCP

client function doesn’t enable. Recommended Action Enable IPv6 DHCP client function on the OOB interface.

(Config)#oob protocol dhcp6

Error Message Error! 'oob protocol dhcp6 restart'. Explanation Duplicate user input ' oob protocol dhcp6 restart '. Recommended Action Use ‘oob protocol dhcp6 restart’.


Error Message DHCP6 Client Restarted. Explanation User input ‘oob protocol dhcp6 restart’ command. Recommended Action Use ‘oob protocol dhcp6 restart’.

Error Message Are you sure you want to restart the DHCP6 client service? (y/n)Explanation User input ‘oob protocol dhcp6 restart’ command. Recommended Action Use ‘oob protocol dhcp6 restart’.

Error Message Changing protocol mode will reset dhcp6 configuration. Explanation User input ‘oob protocol none dhcp6’ command. Recommended Action Use ‘oob protocol none dhcp6’.

Error Message Error! 'ipv6 dhcp6 restart'. Explanation Duplicate user input 'ipv6 dhcp restart'. Recommended Action Use ‘ipv6 dhcp6 restart’.

Error Message Changing protocol mode will reset ipv6 configuration.

Are you sure you want to continue? (y/n) Explanation Changing protocol mode with reset ipv6 IP address for interface

VLAN mode. Recommended Action Use ' ipv6 address protocol dhcp6'

Error Message Incorrect input! Use 'ipv6 address protocol {dhcp6 | none}'. Explanation User input incomplete command. Recommended Action Use ' ipv6 address protocol {dhcp6 | none}'.

Error Message Protocol mode not changed! Explanation User input changing protocol mode command then enter ‘n’ (not

change mode). Recommended Action Use ' ipv6 address protocol {dhcp6 | none}'.

Error Message Only one interface can run DHCP6.

Configure switch port protocol to none. Explanation When user already use oob mgmt interface to configure

DHCPv6, then into interface VLAN mode to changing protocol mode with ipv6 configuration will cause this error message.

Recommended Action Configure oob mgmt interface protocol to none. Use ‘ipv6 address protocol {dhcp6 | none}'.


3.1.13 DNS Relay

This section contains the DNS Relay messages.

Error Message Incorrect input! Use 'ip host <name> <ipAddr|ipv6Addr>' Explanation User input incomplete command . Recommended Action Use 'ip host <name> <ipAddr|ipv6Addr>'

Error Message Incorrect input! Invalid IP Address. Explanation User input an invalid IP address. Recommended Action Can not use reserved IP address ex:224.x.x.x, or invalid IP

address ex: 256.1.1.1

Error Message Incorrect input! Host name must be of 63 characters or less. Explanation User input a host name over 63 characters. Recommended Action Host name must be of 63 characters or less.

Error Message Incorrect input! Use 'no ip host <name>' Explanation User input incomplete command . Recommended Action Use 'no ip host <name>'

Error Message Incorrect input! Use 'ip domain-name <name>' Explanation User input incomplete command . Recommended Action Use 'ip domain-name <name>'

Error Message Incorrect input! Default domain name must be of 63 characters

or less. Explanation User input a domain name over 63 characters. Recommended Action Default domain name must be of 63 characters or less.

Error Message Incorrect input! Use 'ip domain-list <name>' Explanation User input incomplete command . Recommended Action Use 'ip domain-list <name>'

Error Message Incorrect input! Use 'no ip domain-list <name>' Explanation User input incomplete command . Recommended Action Use 'no ip domain-list <name>'


Error Message Incorrect input! Domain list name must be of 63 characters or

less. Explanation User input a domain list name over 63 characters. Recommended Action Domain list name must be of 63 characters or less.

Error Message Incorrect input! Use 'ip name-server <ipAddr|ipv6Addr>' Explanation User input incomplete command . Recommended Action Use 'ip name-server <ipAddr|ipv6Addr>'

Error Message Incorrect input! Use 'no ip name-server <ipAddr|ipv6Addr>' Explanation User input incomplete command . Recommended Action Use 'no ip name-server <ipAddr|ipv6Addr>'


3.1.14 sFlow

This section contains the sFlow messages.

Error Message Incorrect input! use sflow receiver <index> owner <owner>

timeout <time> Explanation User input incomplete command . Recommended Action Use ' sflow receiver <index> owner <owner> timeout <time>'

Error Message Incorrect input! Invalid Receiver index value Explanation User input incomplete command . Recommended Action <index> range 1-8

Error Message Incorrect input! Inavlid IP address Explanation User input incomplete command . Recommended Action Enter Ipv4/ipv6 Address

Error Message Incorrect input! use sflow receiver <index> maxdatagram <size> Explanation User input incomplete command . Recommended Action use sflow receiver <index> maxdatagram <size>

Error Message Incorrect input! Invalid datagram size Explanation User input incomplete command . Recommended Action Enter Size <200 - 9116>.

Error Message Incorrect input! Receiver owner string should be less than 128

characters. Explanation User input incomplete command . Recommended Action owner string should be less than 128 characters.

Error Message Incorrect input! use sflow receiver <index> port <port> Explanation User input incomplete command . Recommended Action use sflow receiver <index> port <port>

Error Message Incorrect input! Invalid command use sflow poller <index> Explanation User input incomplete command . Recommended Action use sflow poller <index>

Error Message Incorrect input! Invalid Receiver index value <1 - 8> Explanation User input incomplete command . Recommended Action Enter index <1-8>

Error Message Incorrect input! Invalid command use sflow poller interval

<interval> Explanation User input incomplete command . Recommended Action use sflow poller interval <interval>

Error Message Incorrect input! Invalid Polling Interval


Explanation User input incomplete command . Recommended Action Enter interval <0 - 86400>

Error Message Incorrect input! Invalid command use sflow sampler <index> Explanation User input incomplete command . Recommended Action use sflow sampler <index>

Error Message Incorrect input! Invalid command use sflow sampler

maxheadersize <size> Explanation User input incomplete command . Recommended Action use sflow sampler maxheadersize <size>

Error Message I Incorrect input! Invalid Header Size Explanation User input incomplete command . Recommended Action Enter Maximum Header size <20 - 256>.

Error Message Incorrect input! Invalid command use sflow sampler rate <rate> Explanation User input incomplete command . Recommended Action use sflow sampler rate <rate>

Error Message Incorrect input! Invalid Sampler Rate. Explanation User input incomplete command . Recommended Action Enter rate <256 - 65536>.

Error Message Error! First assign Receiver index Explanation User input incomplete command . Recommended Action create receive index


3.2 Switching

3.2.1 Forwarding Database

This section contains the Forwarding Database module messages.

Error Message Incorrect input! Use 'mac-address-table aging-time

<10-1000000>'. Explanation Incomplete command for this function. Recommended Action Use 'mac-address-table aging-time <10-1000000>'.

Error Message Incorrect input! Use 'clear mac-addr-table dynamic' Explanation User input incomplete command . Recommended Action Use 'clear mac-addr-table dynamic'


3.2.2 Port

This section contains the port module messages. Error Message Incorrect input! Use 'description <string>'. Explanation User input incomplete command . Recommended Action Use 'description <string>'.

Error Message Maximum allowed length of Description string is 64 characters. Explanation User input description string over 64 characters. Recommended Action Maximum 64 characters can be allowed for interface description.

Error Message In order for physical mode configurations to take effect,

auto-negotiate must be disabled. Use 'no negotiate' command to disable.

Explanation User attempt to change speed of the port which is working on auto-negotiate mode.

Recommended Action Disable auto-negotiate before changing the port speed.

Error Message Incorrect input! Use 'channel-group <logical logical slot/port>'. Explanation User input incomplete command. Recommended Action Use 'channel-group <logical logical slot/port>'.

Error Message Incorrect input! Use 'delete-channel-group <logical logical

slot/port>'. Explanation User input incomplete command. Recommended Action Use 'delete-channel-group <logical logical slot/port>'.

Error Message Incorrect input! Use 'mtu <1518-9216>'. Explanation User input incomplete command. Recommended Action Use 'mtu <1518-9216>'.

Error Message Incorrect input! Use 'capabilities {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'capabilities {10|100|1000 half-duplex|full-duplex}'.


Error Message Incorrect input! Use 'no capabilities {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'no capabilities {10|100|1000 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'capabilities all {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'capabilities all {10|100|1000 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'no capabilities all {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'no capabilities all {10|100|1000 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'speed-duplex {10|100

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'speed-duplex {10|100 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'speed-duplex all {{100|10}

{half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'speed-duplex all {{100|10} {half-duplex|full-duplex}'.

Error Message This function is not available to this port!!! Explanation Only external ports can be changed speed. Internal ports always

fix on 1G speed. Recommended Action User can’t change the speed for the internal ports.

Error Message Incorrect input! This interface is a member of channel group. Explanation User attempt to enable flowcontrol on a member port of channel

group. Recommended Action User is not allowed to enable flow control on port-channel

member port. Please enable the flow control on the port-channel interface.

Error Message Incorrect input! Use 'show interface status {<unit/slot/port> | all}'. Explanation User input incomplete command . Recommended Action Use 'show interface status {<unit/slot/port> | all}'.


Error Message ERROR: syntax error, command: switchport broadcast all

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport broadcast all packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport unicast all

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport unicast all packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport multicast all

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport multicast all packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport broadcast

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport broadcast packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport unicast

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport unicast packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport multicast

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport multicast packet-rate <1-4>'.

Error Message ERROR: syntax error, command: no switchport broadcast all Explanation User input incomplete command . Recommended Action Use command ‘no switchport broadcast all.’

Error Message ERROR: syntax error, command: no switchport unicast all Explanation User input incomplete command . Recommended Action Use command ‘no switchport unicast all’


Error Message ERROR: syntax error, command: no switchport multicast all Explanation User input incomplete command . Recommended Action Use command ‘no switchport multicast all’

Error Message Incorrect input! Use 'port-monitor session <session-id> {mode |

source interface <slot/port> [tx | rx] | destination interface <slo t/port> }'.

Explanation User input incomplete command. Recommended Action Use 'port-monitor session <session-id> {mode | source interface

<slot/port> [tx | rx] | destination interface <slo t/port> }'.

Error Message Incorrect input! Use 'no monitor [session <session-id> [{mode |

source interface <slot/port> | destination interface}]]'. Explanation User input incomplete command. Recommended Action Use 'no monitor [session <session-id> [{mode | source interface

<slot/port> | destination interface}]]'.

Error Message This interface can not be configured as destination port. Explanation User attempt to set the port-channel interface to be destination

port. Recommended Action User can only set the normal ports to be destination port.

Error Message Probe port must be reset before re-configuring it. Explanation User attempt to change the destination port. Recommended Action User must delete the original destination port and then set a new

one.

Error Message Interface is not configured. Explanation User attempt to delete the destination port but it was not created.Recommended Action Make sure the destination had been created.


3.2.3 VLAN

This section contains the VLAN messages. Error Message Incorrect input! Use 'vlan name <1-4093> <name>'. Explanation User input incomplete vlan name. Recommended Action Use ' vlan name <1-4093> <name>'.

Error Message Incorrect input! Use 'no vlan name <1-4093> <name>'. Explanation User input incomplete vlan name. Recommended Action Use ' no vlan name <1-4093> <name>'.

Error Message A default VLAN may not have its name changed. Explanation User try to change the name of default VLAN 1 and the name will

not be changed. Recommended Action The name of default VLAN 1 can not change.

Error Message VLAN ID not found. Explanation User input an non-existed VLAN name. Recommended Action It should be created the VLAN first.

Error Message VLAN name must contain alphanumeric characters only. Explanation User input incomplete vlan name. Recommended Action Use alphanumeric characters only for VLAN name.

Error Message Incorrect input! Use 'switchport acceptable-frame-type all

{all|tagged}'. Explanation User input incomplete command. Recommended Action Use 'switchport acceptable-frame-type all {all|tagged}'.

Error Message Incorrect input! Use 'switchport acceptable-frame-type

{all|tagged}'. Explanation User input incomplete command. Recommended Action Use 'switchport acceptable-frame-type {all|tagged}'.

Error Message ERROR: no such vlan id Explanation User adds an interface to a non-existed VLAN. Recommended Action Use a existed VLAN ID.


Error Message Incorrect input! Use 'switchport forbidden vlan {add | remove}

<vlan-id>' Explanation User input incomplete command. Recommended Action Use 'switchport forbidden vlan {add | remove} <vlan-id>'

Error Message Error: Failed to join forbidden list Explanation User attempt to join native VLAN ID to forbidden list. Recommended Action Make sure the VLAN ID is not the native VLAN ID.

Error Message ERROR: This VLAN does not exist. Explanation User attempt to join a non-exist VLAN ID to forbidden list. Recommended Action Make sure the VLAN ID is exist.

Error Message ERROR: syntax error, command: switchport allowed vlan {add

[tagged | untagged] | remove} <vlan-id> Explanation User input incomplete command. Recommended Action Use command ‘switchport allowed vlan {add [tagged | untagged]

| remove} <vlan-id>’

Error Message ERROR: syntax error, command: switchport allowed vlan {add

[tagged|untagged] | remove} all <vlan-id> Explanation User input incomplete command. Recommended Action Use command ‘switchport allowed vlan {add [tagged|untagged] |

remove} all <vlan-id>’

Error Message ERROR: failed to remove vlan egress list. Explanation User attempt to remove native VLAN ID group. Recommended Action Can not remove VLAN ID that has been set native VALN ID for

the interface. Please set native VLAN to other VLAN ID and then remove it.

Error Message Incorrect input! Use 'switchport native vlan <1-3965>'. Explanation User input incomplete command. Recommended Action Use 'switchport native vlan <1-3965>'.

Error Message Incorrect input! Use 'switchport native vlan all <1-3965>'. Explanation User input incomplete command. Recommended Action Use 'switchport native vlan all <1-3965>'.


Error Message Failed to set the native vlan with the Dynamic VLAN type. Explanation User attempt to set native VLAN of the interface with Dynamic

VLAN ID. Recommended Action Dynamic VLAN ID can not be set for native VLAN.

Error Message Incorrect input! Use 'switchport tagging <1-3965>'. Explanation User input incomplete command. Recommended Action Use 'switchport tagging <1-3965>'.

Error Message Incorrect input! Use 'no switchport tagging <1-3965>'. Explanation User input incomplete command. Recommended Action Use 'no switchport tagging <1-3965>'.

Error Message Incorrect input! Use 'switchport tagging all <1-3965>'. Explanation User input incomplete command. Recommended Action Use 'no switchport tagging <1-3965>'.

Error Message Incorrect input! Use 'no switchport tagging all <1-3965>'. Explanation User input incomplete command. Recommended Action Use 'no switchport tagging all <1-3965>'.

Error Message Incorrect input! Use 'vlan makestatic <2-4094>'. Explanation User input incomplete command. Recommended Action Use 'vlan makestatic <2-4094>'.

Error Message Incorrect input! Use 'vlan ?' to list commands. Explanation User input incorrect vlan comment. Recommended Action Use 'vlan ?' to list commands.

Error Message Can't Create/Delete a VLAN, when the VTP client is enabled. Explanation User can’t create or delete a VLAN when the switch is configured

with VTP client. Recommended Action Change to VTP server mode.

Error Message VLAN already exists. Explanation User create a VLAN, and it was existed. Recommended Action Use create a new VLAN.


Error Message Can't remove the management VLAN. Explanation User try to delete the default of management VLAN 1. Recommended Action User can't remove the management VLAN 1.

Error Message Cannot delete the default VTP VLANs Explanation User try to delete the default VLAN of VTP. Recommended Action User can't remove the default VLAN of VTP from 1002 to 1005.

Error Message VLAN does not exist. Explanation User deleted the VLAN is not existed. Recommended Action User can't remove the nonexistent VLAN.

Error Message The group does not exist. Explanation User configure the VLAN associated with a non-exist particular

group. Recommended Action Create a Protocol-based VLAN group first.

Error Message Failed to associate IP Subnet to a VLAN. Explanation User failed to associate a un-exist VLAN to a IP subnet. Recommended Action User can't associate IP subnet to a nonexistent VLAN.

Error Message Incorrect input! Use 'show vlan [association {{mac [<macaddr>]}

| {subnet [<ipaddr> <netmask>]}] | [name <name>] | [id <id>]'. Explanation User input incomplete command. Recommended Action Use 'show vlan [association {{mac [<macaddr>]} | {subnet

[<ipaddr> <netmask>]}] | [name <name>] | [id <id>]'.


3.2.4 Protocol-based VLAN

This section contains the Protocol-based VLAN module messages. Error Message The group does not exist. Explanation User adds a protocol to an nonexistent group. Recommended Action Create a Protocol-based VLAN group first.

Error Message The group already exists. Explanation User attempt to add a protocol group name that had been

created. Recommended Action Create a protocol group name with an unused name.

Error Message Incorrect input! Use 'switchport protocol group <groupname>'. Explanation User input incomplete command. Recommended Action Use 'switchport protocol group <groupname>'.

Error Message VLAN Protocol Group name must be less than 16 characters Explanation User input a group name over 16 characters. Recommended Action Use a group name less than 16 characters.

Error Message Incorrect input! Use 'switchport protocol group add protocol

<groupname> {ip|arp|ipx}'. Explanation User input incomplete command. Recommended Action Use 'switchport protocol group add protocol <groupname>

{ip|arp|ipx}'.

Error Message Incorrect input! Use 'no switchport protocol group <groupname>'.Explanation User input incomplete command. Recommended Action Use 'no switchport protocol group <groupname>'.

Error Message Incorrect input! Use 'no switchport protocol group add protocol

<groupname> {ip|arp|ipx}'. Explanation User input incomplete command. Recommended Action Use 'no switchport protocol group add protocol <groupname>

{ip|arp|ipx}'.


Error Message Incorrect input! Use 'protocol group <groupname> <vlanid>'. Explanation User input incomplete command. Recommended Action Use 'protocol group <groupname> <vlanid>'.

Error Message Incorrect input! Use 'no protocol group <groupname> <vlanid>'. Explanation User input incomplete command. Recommended Action Use 'no protocol group <groupname> <vlanid>'.

Error Message Incorrect input! Use 'switchport protocol group all <groupname>'.Explanation User input incomplete command. Recommended Action Use 'switchport protocol group all <groupname>'.

Error Message Incorrect input! Use 'no switchport protocol group all

<groupname>'. Explanation User input incomplete command. Recommended Action Use 'no switchport protocol group all <groupname>'.


3.2.5 IP Subnet-based VLAN

This section contains the IP Subnet-based VLAN module messages. Error Message Incorrect input! Use 'vlan association {mac <macaddr> <vlanId>

| subnet <ipaddr> <netmask> <vlanId>}' Explanation User input incomplete command. Recommended Action Use 'vlan association {mac <macaddr> <vlanId> | subnet

<ipaddr> <netmask> <vlanId>}'

Error Message Incorrect input! Use 'vlan association subnet <ipaddr>

<netmask> <vlanId>'. Explanation User input incomplete command. Recommended Action Use 'vlan association subnet <ipaddr> <netmask> <vlanId>'.

Error Message Incorrect input! Use 'no vlan association subnet <ipaddr>

<netmask>'. Explanation User input incomplete command. Recommended Action Use 'no vlan association subnet <ipaddr> <netmask>'.

Error Message The IP address and subnet mask combination is not valid. Explanation The IP address is not match the subnet mask. Recommended Action Set the valid IP address which can match the subnet mask.

Error Message Subnet mask must have contiguous ones and be no longer than

30 bits. Explanation The the subnet mask is invalid. Recommended Action Set the subnet mask with contiguous ones and be no longer than

30 bits.

Error Message Incorrect input! netmask must have contiguous ones. Explanation The the subnet mask is not contiguous ones. Recommended Action Set the subnet mask with contiguous ones and be no longer than

30 bits.

Error Message Incorrect input! <ipaddr> must be a valid IP address. Explanation The the IP address is invalid. Recommended Action Set the valid IP address with 0 to 255 numeric characters in form

x.x.x.x and avoid the reserved IP address.


Error Message Failed to associate IP Subnet to a VLAN. Explanation The IP Subnet associate to a invalid VLAN. Recommended Action Associate the IP Subnet to a valid and existed VLAN.

Error Message Failed to delete association of IP Subnet from VLAN. Explanation The association of IP Subnet is not existed. Recommended Action Delete the association of IP Subnet which is already existed.


3.2.6 MAC-based VLAN

This section contains the MAC-based VLAN module messages. Error Message Incorrect input! Use 'vlan association mac <macaddr> <vlanId>' Explanation User input incomplete command. Recommended Action Use 'vlan association mac <macaddr> <vlanId>'

Error Message Incorrect input! Use 'no vlan association mac <macaddr>' Explanation User inputs incomplete command. Recommended Action Use 'no vlan association mac <macaddr>'

Error Message User Input Error: Invalid MAC Address Explanation User inputs invalid MAC Address. Recommended Action Correct the format of MAC Address.

Error Message Failed to associate MAC Address to VLAN . Explanation User attempt to associate MAC Address to a non-exist VLAN. Recommended Action Create the VLAN ID first.

Error Message Failed to retrieve VLAN ID from MAC Address. Explanation User attempt to retrieve VLAN ID from a non-exist MAC

Address. Recommended Action Create the VLAN ID first.


3.2.7 GARP

This section contains the GARP module messages. Error Message Incorrect input! Use 'garp timer join all <10-100>'. Explanation User input incomplete command. Recommended Action Use 'garp timer join all <10-100>'.

Error Message Incorrect input! Use 'garp timer join <10-100>'. Explanation User input incomplete command. Recommended Action Use 'garp timer join <10-100>'.

Error Message Incorrect input! Use 'garp timer leave <20-600>'. Explanation User input incomplete command. Recommended Action Use 'garp timer join <10-100>'.

Error Message Incorrect input! Use 'garp timer leave all <20-600>'. Explanation User input incomplete command. Recommended Action Use 'garp timer leave all <20-600>'.

Error Message Incorrect input! Use 'garp timer leaveall all <200-6000>'. Explanation User input incomplete command. Recommended Action Use 'garp timer leaveall all <200-6000>'.

Error Message Incorrect input! Use 'garp timer leaveall <200-6000>'. Explanation User input incomplete command. Recommended Action Use 'garp timer leaveall <200-6000>'.

Error Message Please disable VTP at first. Explanation Cannot run VTP & GVRP at the same time. Recommended Action Disable the VTP function before enabling GVRP.

Error Message Incorrect input! Use 'show garp configuration { <slot/port> | all }'. Explanation User input incomplete command. Recommended Action Use 'show garp configuration { <slot/port> | all }'.


Error Message Incorrect input! Use 'show gvrp configuration { <slot/port> | all }'. Explanation User input incomplete command. Recommended Action Use 'show garp configuration { <slot/port> | all }'.

Error Message Incorrect input! Use 'show gmrp configuration { <slot/port> | all }'.Explanation User input incomplete command. Recommended Action Use 'show gmrp configuration { <slot/port> | all }'.


3.2.8 VTP

This section contains the VTP module messages.

Error Message Please disable GVRP at first!! Explanation Cannot run VTP & GVRP at the same time. Recommended Action Disable the GVRP function before enabling VTP.

Error Message Incorrect input! Use 'vtp domain <DomainName>' Explanation User input incomplete command. Recommended Action Use 'vtp domain <DomainName>'

Error Message Incorrect input! Domain name must less than 32 characters. Explanation User input over 32 characters for VTP domain name. Recommended Action Maximum 32 characters can be used for VTP domain name.

Error Message Incorrect input! Domain name contents alphanum characters

only. Explanation User input non-alphanum characters for VTP domain name. Recommended Action Domain name contents alphanum characters only.

Error Message Incorrect input!! Use 'vtp mode {client|server|transparent}'. Explanation User input incomplete command. Recommended Action Use 'vtp mode {client|server|transparent}'.

Error Message Incorrect input!! Use 'vtp password <string>'. Explanation User input incomplete command. Recommended Action Use 'vtp password <string>'.

Error Message Incorrect input!! Password string must less than 64 characters. Explanation User input 64 characters for VTP password. Recommended Action Maximum 64 characters can be used for VTP password.

Error Message Incorrect input!! Password string contents alphanum only. Explanation User input non-alphanum characters for VTP password. Recommended Action Password string contents alphanum only.


Error Message Incorrect Input!! Use 'show vtp

{counters|password|status|trunkport}'. Explanation User input incomplete command . Recommended Action Use 'show vtp {counters|password|status|trunkport}'.

Error Message Please enable VTP at first! Use 'vtp' Explanation User attempt to enable VTP sub function,but VTP admin mode is

disable. Recommended Action Use command 'vtp' to enable admin mode first.

Error Message Invalid Interface! <IntIfNum> is a member of the port-channel ! Explanation User attempt to enable VTP trunkport on a member port of

port-channel. Recommended Action VTP trunkport can not be enabled on port-channel member port.

Error Message Incorrect Input!! Use 'show vtp

{counters|password|status|trunkport}'. Explanation User input incomplete command. Recommended Action Use 'show vtp {counters|password|status|trunkport}'.


3.2.9 IGMP Snooping


Error Message Incorrect input! Use 'ip igmp snooping static <macaddr> vlan

<vlan-id> interface <unit/slot/port> Explanation Incomplete command for this function. Recommended Action Use 'ip igmp snooping static <macaddr> vlan <vlan-id> interface

<unit/slot/port>

Error Message IGMP Snooping ADMIN must be enable. Use 'ip igmp snooping'

command to enable. Explanation User attempt to set static multicast group before enable ip igmp

snooping. Recommended Action Use 'ip igmp snooping' command to enable IGMP Snooping first.

Error Message This function is not allowed on port-channel members. Explanation User attempt to set static multicast group on a port-channel

member. But it is failed. Recommended Action The static multicast group can not be configured on port-channel

members.

Error Message User Input Error: Invalid MAC Address Explanation User input invalid format of MAC Address. Recommended Action Correct the format of MAC Address.

Error Message Incorrect input! Use 'ip igmp snooping mrouter interface'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ip igmp snooping mrouter interface'.

Error Message Incorrect input! Use 'no ip igmp snooping mrouter interface'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no ip igmp snooping mrouter interface'.

Error Message Incorrect input! Use 'ip igmp snooping groupmembershipinterval

<2-3600>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ip igmp snooping

groupmembershipinterval <2-3600>'.


Error Message Incorrect input! Use 'ip igmp snooping max-response-time

<1-3599>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘Incorrect input! Use 'ip igmp snooping

max-response-time <1-3599>'.

Error Message Incorrect input! Use 'ip igmp snooping mcrtrexpiretime

<0-3600>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘ip igmp snooping mcrtrexpiretime

<0-3600>'.

Error Message Incorrect input! Use 'set igmp <vlanId>' Explanation User input incomplete command. Recommended Action Use 'set igmp <vlanId>'

Error Message Incorrect input! Use 'no set igmp <vlanId>' Explanation User input incomplete command. Recommended Action Use 'no set igmp <vlanId>'

Error Message Incorrect input! Use 'set igmp fast-leave <vlanId>' Explanation User input incomplete command. Recommended Action Use 'set igmp fast-leave <vlanId>'

Error Message Incorrect input! Use 'no set igmp fast-leave <vlanId>' Explanation User input incomplete command. Recommended Action Use 'no set igmp fast-leave <vlanId>'

Error Message Incorrect input! Use 'set igmp groupmembership-interval

<vlanId> <group-membership-interval>' Explanation User input incomplete command. Recommended Action Use 'set igmp groupmembership-interval <vlanId>

<group-membership-interval>'

Error Message Incorrect input! Use 'no set igmp groupmembership-interval

<vlanId>' Explanation User input incomplete command. Recommended Action Use 'no set igmp groupmembership-interval <vlanId>'


Error Message Incorrect input! Use 'set igmp maxresponse <vlanId>

<max-response-time>' Explanation User input incomplete command. Recommended Action Use 'set igmp maxresponse <vlanId> <max-response-time>'

Error Message Incorrect input! Use 'no set igmp maxresponse <vlanId>' Explanation User input incomplete command. Recommended Action Use 'no set igmp maxresponse <vlanId>'

Error Message Incorrect input! Use 'set igmp mcrtrexpiretime <vlanId>

<mcrouter-expiry-time>' Explanation User input incomplete command. Recommended Action Use 'set igmp mcrtrexpiretime <vlanId> <mcrouter-expiry-time>'

Error Message Incorrect input! Use 'no set igmp mcrtrexpiretime <vlanId>' Explanation User input incomplete command. Recommended Action Use 'no set igmp mcrtrexpiretime <vlanId>'

Error Message Incorrect input! Use 'ip igmp snooping querier version <version>' Explanation Incomplete command for this function. Recommended Action Use complete command 'ip igmp snooping querier version

<version>'.

Error Message Incorrect input! Use 'ip igmp snooping querier address

<ipv4addr>' Explanation Incomplete command for this function. Recommended Action Use complete command ' ip igmp snooping querier address

<ipv4addr>'.

Error Message Incorrect input! <ipv4addr> must be a valid IPv4 address. Explanation User input invalid ip address. Recommended Action Correct the format of ip address.

Error Message Incorrect input! Use unicast IPv4 address. Explanation User input unicast ip address. Recommended Action Correct the format of ip address.


Error Message Incorrect input! Use 'ip igmp snooping querier <vlanid> address

<ipv4addr>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'ip igmp snooping querier <vlanid>

address <ipv4addr>'.

Error Message Incorrect input! Use 'ip igmp snooping querier <vlanid>'. Explanation Incomplete command for this function. Recommended Action Use complete command ' ip igmp snooping querier <vlanid>'.

Error Message Incorrect input! Use 'no set igmp querier <vlanid>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'no ip igmp snooping querier <vlanid>'.

Error Message Incorrect input! Use 'ip igmp snooping querier query-interval

<interval>' Explanation Incomplete command for this function. Recommended Action Use complete command ' ip igmp snooping querier

query-interval <interval>'.

Error Message Incorrect input! Use 'ip igmp snooping querier

querier-expiry-interval <interval>' Explanation Incomplete command for this function. Recommended Action Use complete command 'ip igmp snooping querier

querier-expiry-interval <interval>'.

Error Message Incorrect input! Use 'show igmp snooping mrouter

[{interface|vlan} <slot/port>].' Explanation User input incomplete command. Recommended Action Use 'show igmp snooping mrouter [{interface|vlan} <slot/port>].'

Error Message Incorrect input! Use 'show mac-address-table multicast {all

|[<macaddr> <vlanid>]}'. Explanation User input incomplete command. Recommended Action Use 'show mac-address-table multicast {all |[<macaddr>

<vlanid>]}'.


This section contains the IBP Port-Channel module messages.

Error Message Incorrect input! Use 'igmp-snooping <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'igmp-snooping <uplinkSetName>'.

Error Message Incorrect input! Use 'no igmp-snooping <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no igmp-snooping <uplinkSetName>'.

Error Message Incorrect input! Use 'show igmp-snooping [<uplinkSetName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command 'show igmp-snooping

[<uplinkSetName>]'.


3.2.10 MLD Snooping

This section contains the MLD module messages.

Error Message Incorrect input! Use ? to list command'. Explanation User input incomplete command. Recommended Action Use ' ipv6 mld snooping interfacemode all’ and ‚ no ipv6 mld

snooping interfacemode all’.

Error Message Incorrect input! Use 'ipv6 mld snooping

groupmembershipinterval <2-3600>'. Explanation User input incomplete command. Recommended Action Use 'ipv6 mld snooping groupmembershipinterval <2-3600>'.

Error Message Incorrect input! Use 'ipv6 mld snooping max-response-time

<1-3599>'. Explanation User input incomplete command. Recommended Action Use 'ipv6 mld snooping max-response-time <1-3599>'.

Error Message Incorrect input! Use 'ipv6 mld snooping mcrtrexpiretime

<0-3600>'. Explanation User input incomplete command. Recommended Action Use 'ipv6 mld snooping mcrtrexpiretime <0-3600>'.

Error Message Incorrect input! Use 'ipv6 mld snooping static <macaddr> vlan

<vlan-id> interface <unit/slot/port> Explanation User input incomplete command. Recommended Action Use 'ipv6 mld snooping static <macaddr> vlan <vlan-id>

interface <unit/slot/port>

Error Message Incorrect input! Use 'ipv6 mld snooping interfacemode'. Explanation User input incomplete command. Recommended Action Use 'ipv6 mld snooping interfacemode'.

Error Message Incorrect input! Use 'no ipv6 mld snooping interfacemode'. Explanation User input incomplete command. Recommended Action Use 'no ipv6 mld snooping interfacemode'.


Error Message Incorrect input! Use 'ipv6 mld snooping mrouter interface'. Explanation User input incomplete command. Recommended Action Use 'ipv6 mld snooping mrouter interface'.

Error Message Incorrect input! Use 'no ipv6 mld snooping mrouter interface'. Explanation User input incomplete command. Recommended Action Use 'no ipv6 mld snooping mrouter interface'.

Error Message Incorrect input! Use 'ipv6 mld snooping querier address

<ipv6addr>'. Explanation Incomplete command for this function. Recommended Action Use complete command ' ipv6 mld snooping querier address

<ipv6addr>'.

Error Message Incorrect input! <ipV6addr> must be a valid IPv6 address. Explanation User input invalid ipv6 address. Recommended Action Correct the format of ipv6 address.

Error Message Incorrect input! Use unicast link local IPv6 address. Explanation User input unicast ipv6 address. Recommended Action Correct the format of ipv6 address.

Error Message Incorrect input! Use 'ipv6 mld querier <vlanid> address

<ipv6addr>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'ipv6 mld querier <vlanid> address

<ipv6addr>'.

Error Message Incorrect input! Use 'set mld snooping querier <vlanid>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'ipv6 mld snooping querier vlan

<vlanid>'.

Error Message Incorrect input! Use 'no ipv6 mld snooping querier <vlanid>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'no ipv6 mld snooping querier vlan

<vlanid>'.


Error Message Incorrect input! Use 'ipv6 mld snooping querier query-interval

<interval>' Explanation Incomplete command for this function. Recommended Action Use complete command ' ipv6 mld snooping querier

query-interval <interval>'.

Error Message Incorrect input! Use 'ipv6 mld snooping querier

querier-expiry-interval <interval>' Explanation Incomplete command for this function. Recommended Action Use complete command ' ipv6 mld snooping querier

querier-expiry-interval <interval>'.

Error Message Incorrect input! Use 'no set mld <vlanId>' Explanation User input incomplete command. Recommended Action Use ' no set mld <vlanId>'.

Error Message Incorrect input! Use 'set mld <vlanId>' Explanation User input incomplete command. Recommended Action Use ' set mld <vlanId>’.

Error Message Incorrect input! Use 'no set mld fast-leave <vlanId>' Explanation User input incomplete command. Recommended Action Use ' no set mld fast-leave <vlanId>'.

Error Message Incorrect input! Use 'set mld groupmembership-interval <vlanId>

<group-membership-interval>' Explanation User input incomplete command. Recommended Action Use ' set mld groupmembership-interval <vlanId>

<group-membership-interval>'.

Error Message Incorrect input! Use 'no set mld groupmembership-interval

<vlanId>' Explanation User input incomplete command. Recommended Action Use ' no set mld groupmembership-interval <vlanId>'.


Error Message Incorrect input! Use 'set mld maxresponse <vlanId>

<max-response-time>' Explanation User input incomplete command. Recommended Action Use 'set mld maxresponse <vlanId> <max-response-time>'.

Error Message Incorrect input! Use 'no set mld maxresponse <vlanId>' Explanation User input incomplete command. Recommended Action Use ' no set mld maxresponse <vlanId>'.

Error Message Incorrect input! Use 'set mld mcrtrexpiretime <vlanId>

<mcrouter-expiry-time>' Explanation User input incomplete command. Recommended Action Use 'set mld mcrtrexpiretime <vlanId> <mcrouter-expiry-time>'.

Error Message Incorrect input! Use 'no set mld mcrtrexpiretime <vlanId>' Explanation User input incomplete command. Recommended Action Use ' no set mld mcrtrexpiretime <vlanId>'.

Error Message Maximum Response Time should be lesser than the Group

Membership Interval for the VLAN. Explanation User input invalid value for Maximum Response Time. Recommended Action The value of Maximum Response Time must be lesser than the

Group Membership Interval for that VLAN. Use 'set mld maxresponse <vlanId> <max-response-time>'.

Error Message Group Membership Interval should be Greater than the

Maximum Response Time for the VLAN. Explanation User input invalid value for the Group Membership Interval. Recommended Action The value of the Group Membership Interval must be greater

than the Response Time for that VLAN. Use ' set mld groupmembership-interval <vlanId> <group-membership-interval>'.

Error Message ERROR: Group Membership Interval must be greater than the

Maximum Response Time. Explanation User input invalid value of the Group Membership Interval. Recommended Action Group Membership Interval must be greater than the Maximum

Response Time. Use ' ipv6 mld snooping groupmembershipinterval <2-3600>'.


3.2.11 Multicast Forwarding Database

This section contains the Multicast Forwarding Database module messages.

Error Message Incorrect input! Use 'show mac-address-table multicast {all

|[<macaddr> <vlanid>]}'. Explanation User input incomplete command. Recommended Action Use 'show mac-address-table multicast {all |[<macaddr>

<vlanid>]}'.


3.2.12 Port-Channel

This section contains the Port-Channel module messages. Error Message Incorrect input! Use 'load-balance

{dst-ip|dst-mac|src-dst-ip|src-dst-mac|src-ip|src-mac}'. Explanation Incomplete command for this function. Recommended Action Use complete command Use 'load-balance

{dst-ip|dst-mac|src-dst-ip|src-dst-mac|src-ip|src-mac}'.

Error Message Invalid interface <IntIfNum>, is not a port-channel interface. Explanation The interface is not a port-channel interface. Recommended Action Use correct port-channel interface.

Error Message Incorrect input! Use 'no port-channel load-balance all'. Explanation Incomplete command for this function. Recommended Action Use 'no port-channel load-balance all'.

Error Message Cannot change the auto-negotiate mode of a port-channel

member. Explanation The port-channel member port can NOT be changed to

auto-negotiate mode . Recommended Action Use this command only on normal port.

Error Message Could not create. Maximum number of port-channels (64)

reached. Explanation User creates more than 64 port-channel groups. Recommended Action User just can create maximum 64 port-channel groups.

Error Message Error: Characters in the port-channel name must be

alphanumeric and can contain dashes or underscores. Explanation User input a port-channel name with non-alphanumeric

characters. Recommended Action Use alphanumeric and dashes or underscores for port-channel

name.

Error Message No port-channels exist. Explanation There is no port-channel exist. Recommended Action Create a port-chnnel first.


Error Message Ports cannot be added to disabled port-channels. Explanation User attempt to add a member to a disabled port-channel. Recommended Action Enable the port-channel before add member ports.

Error Message Ports being added to a port-channel must not be participating in

MAC Filtering. Explanation User attempt to add a interface to a port-channel, but the

interface has been set with MAC filter function. Recommended Action Use command ‘no macfilter addsrc <macaddr>’ to remove the

MAC Filter setting first, and then use command ‘channel-group <unit/slot/port>’ to add interface to the port-channel.

Error Message Could not create. This port-channel name already exists. Explanation User create a port-channel name that already exists. Recommended Action Use another port-channel name.

Error Message [slot/port] is not a configured port-channel. Explanation User try to display the port-channel information for

non-port-channel interface. Recommended Action Use correct port-channel interface slot/port for this command.

Error Message Port-channel name must be less than 16 characters. Explanation User attempt to crate a port-channel name is over 15 characters.Recommended Action Configure port-channel name within 15 characters.

Error Message Incorrect input! Use 'port-channel load-balance all

{dst-ip|dst-mac|src-dst-ip|src-dst-mac|src-ip|src-mac}'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-channel load-balance all


Error Message Incorrect input! Use 'port-channel name {<logical slot/port> | all}

<name>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-channel name {<logical slot/port> |

all} <name>'.

Error Message Port-channel name is too long. Explanation User attempt to rename a port-channel name over 15

characters. Recommended Action Configure port-channel name within 15 characters.


Error Message Incorrect input! Use 'port-channel <name>'. Explanation User input incomplete command. Recommended Action Use 'port-channel <name>'.

Error Message Incorrect input! Use 'no port-channel {<logical unit/slot/port> |

all}'. Explanation User input incomplete command. Recommended Action Use 'no port-channel {<logical unit/slot/port> | all}'.

Error Message Incorrect input! Use 'port-channel adminmode all'. Explanation User input incomplete command. Recommended Action Use 'port-channel adminmode all'.

Error Message Incorrect input! Use 'no port-channel adminmode all'. Explanation User input incomplete command. Recommended Action Use 'no port-channel adminmode all'.

Error Message Incorrect input! Use 'port-channel linktrap {<logical unit/slot/port>

| all}'. Explanation User input incomplete command. Recommended Action Use 'port-channel linktrap {<logical unit/slot/port> | all}'.

Error Message Incorrect input! Use 'no port-channel linktrap {<logical slot/port> |

all} '. Explanation User input incomplete command. Recommended Action Use 'no port-channel linktrap {<logical slot/port> | all} '.

Error Message Incorrect input! Use 'delete-channel-group <logical slot/port> all' Explanation User input incomplete command. Recommended Action Use 'delete-channel-group <logical slot/port> all'


3.2.13 Spanning-Tree

This section contains the Spanning-Tree module messages. Error Message Incorrect input! Use 'spanning-tree mode {stp | mstp | rstp}'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree mode {stp | mstp | rstp}'.

Error Message Incorrect input! Use 'spanning-tree configuration name <name>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree configuration name <name>'.

Error Message Incorrect input! Use 'spanning-tree configuration revision

<0-65535>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree configuration revision <0-65535>'.

Error Message Incorrect input! Use 'spanning-tree max-age <6-40>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree max-age <6-40>'.

Error Message Incorrect input! Use 'spanning-tree max-hops <1-127>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree max-hops <1-127>'.

Error Message Incorrect input! Use 'spanning-tree hello-time <1-10>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree hello-time <1-10>'.

Error Message Incorrect input! Use 'spanning-tree forward-time <4-30>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree forward-time <4-30>'.

Error Message Incorrect input! Use 'spanning-tree port mode all'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree port mode all'.


Error Message Incorrect input! Use 'no spanning-tree port mode all'. Explanation User input incomplete command . Recommended Action Use 'no spanning-tree port mode all'.

Error Message Incorrect input! Use 'spanning-tree mst instance <mstid>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree mst instance <mstid>'.

Error Message Incorrect input! Use 'no spanning-tree mst instance <mstid>'. Explanation User input incomplete command . Recommended Action Use 'no spanning-tree mst instance <mstid>'.

Error Message Incorrect input! Use 'spanning-tree mst vlan <mstid> <vlan>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree mst vlan <mstid> <vlan>'.

Error Message Incorrect input! Use 'no spanning-tree mst vlan <mstid> <vlan>'. Explanation User input incomplete command . Recommended Action Use 'no spanning-tree mst vlan <mstid> <vlan>'.

Error Message Incorrect input! Use 'spanning-tree mst priority <mstid>

<0-61440>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree mst priority <mstid> <0-61440>'.

Error Message Incorrect input! Use 'no spanning-tree mst priority <mstid>'. Explanation User input incomplete command . Recommended Action Use 'no spanning-tree mst priority <mstid>'.

Error Message Incorrect input! Use 'spanning-tree mst <mstid> {{cost

<1-200000000> |auto}|{port-priority <0-240>}|{external-cost <1-200000000>|auto}}'.

Explanation User input incomplete command . Recommended Action Use 'spanning-tree mst <mstid> {{cost <1-200000000>

|auto}|{port-priority <0-240>}|{external-cost <1-200000000>|auto}}'.


Error Message Incorrect input! Use 'no spanning-tree mst <mstid> {cost |

port-priority | external-cost}'. Explanation User input incomplete command . Recommended Action Use 'no spanning-tree mst <mstid> {cost | port-priority |

external-cost}'.

Error Message Incorrect input! Use ? to list command'. Explanation User input incomplete command . Recommended Action Use ? to list command and complete the command.

Error Message This command only works on dot1d mode. Explanation Spanning-tree edgeport bpdufilter only can be enabled on STP

mode. Recommended Action Change spanning-tree mode to STP <802.1d> first.

Error Message This command only works on dot1d mode. Explanation Spanning-tree edgeport bpduguard only can be enabled on STP

mode. Recommended Action Change spanning-tree mode to STP <802.1d> first.

Error Message This command only works on dot1d mode. Explanation Spanning-tree loopguard only can be enabled on STP mode. Recommended Action Change spanning-tree mode to STP <802.1d> first.

Error Message This command only works on dot1d mode. Explanation Spanning-tree uplinkfast only can be enabled on STP mode. Recommended Action Change spanning-tree mode to STP <802.1d> first.

Error Message Incorrect input! Use 'no spanning-tree guard { loop|none|root }'. Explanation User input incomplete command . Recommended Action Use 'no spanning-tree guard { loop|none|root }'.

Error Message Incorrect input! Use 'show spanning-tree interface

<unit/slot/port>'. Explanation User input incomplete command . Recommended Action Use 'show spanning-tree interface <unit/slot/port>'.


Error Message Incorrect input! Use 'show spanning-tree mst { detailed <mstid> |

summary | port { detailed <mstid> <unit/slot/port> | summary <mstid> { <unit/slot/port> | all } } }'

Explanation User input incomplete command . Recommended Action Use 'show spanning-tree mst { detailed <mstid> | summary |

port { detailed <mstid> <unit/slot/port> | summary <mstid> { <unit/slot/port> | all } } }'

Error Message Incorrect input! Use 'show spanning-tree mst port { detailed

<mstid> <unit/slot/port> | summary <mstid> { <unit/slot/port> | all } }'

Explanation User input incomplete command . Recommended Action Use 'show spanning-tree mst port { detailed <mstid>

<unit/slot/port> | summary <mstid> { <unit/slot/port> | all } }'

Error Message Incorrect input! Use 'show spanning-tree mst detailed <0-4094>'.Explanation User input incomplete command . Recommended Action Use 'show spanning-tree mst detailed <0-4094>'.

Error Message Incorrect input! Use 'show spanning-tree vlan <vlan>'. Explanation User input incomplete command . Recommended Action Use 'show spanning-tree vlan <vlan>'.

Error Message Incorrect input! Use 'show spanning-tree mst port summary

<mstid> {<unit/slot/port> | all}'. Explanation User input incomplete command . Recommended Action Use 'show spanning-tree mst port summary <mstid>

{<unit/slot/port> | all}'.

Error Message Incorrect input! Use 'show spanning-tree mst port detailed

<mstid> <unit/slot/port>'. Explanation User input incomplete command . Recommended Action Use 'show spanning-tree mst port detailed <mstid>

<unit/slot/port>'.

Error Message Error: MST ID must be in the range of 1 and 4094. Explanation User input a MST ID out of range . Recommended Action MST ID must be in the range of 1 and 4094.


Error Message Error: The VLAN ID specified does not correspond to an existing

VLAN. Explanation User attempt to add a non-exist VLAN to MST instance. Recommended Action Use exist VLAN ID or create the VLAN ID first.

Error Message Error: Could not create the MST instance. Explanation User attempt to create an exist MST instance. Recommended Action Use other MST instance number to create.

Error Message Error: Could not delete the MST instance. Explanation User attempt to delete a non-exist MST instance. Recommended Action Make sure the MST instance is exist.

Error Message Error: Could not add the VLAN to the MST instance. Explanation User attempt to add VLAN to a non-exist MST instance. Recommended Action Create the MST instance first.

Error Message Error: Could not remove the VLAN from the MST instance. Explanation User attempt to delete VLAN from a non-exist MST instance. Recommended Action Create the MST instance first.

Error Message Error: Maximum MST instance Reached. Explanation User attempt to create MST instance when table is full. Recommended Action Maximum 32 MST instances can be created.

Error Message Error: Configuration name can not exceed 32 characters in

length. Explanation User input a Configuration name over 32 characters. Recommended Action Maximum 32 characters in length can be set for Configuration

name.

Error Message Error: Configuration name can not exceed 32 characters in

length. Explanation User input a Configuration name over 32 characters. Recommended Action Maximum 32 characters in length can be set for Configuration

name.


Error Message Incorrect input! Use 'spanning-tree configuration revision

<0-65535>'. Explanation User input incomplete command . Recommended Action Use 'spanning-tree configuration revision <0-65535>'.

Error Message Error: Could not set the bridge maxage.

The bridge maxage value must be less than or equal to 2 * (bridge forwarddelay - 1) and greater than or equal to 2 * (bridge hellotime + 1).

Explanation User input invalid value for setting bridge maxage. Recommended Action The bridge hellotime value must be less than or equal to (bridge

maxage / 2) - 1.

Error Message Error: Could not set the bridge hellotime.

The bridge hellotime value must be less than or equal to (bridge maxage / 2) - 1.

Explanation User input invalid value for setting bridge hellotime. . Recommended Action The bridge hellotime value must be less than or equal to (bridge

maxage / 2) - 1.

Error Message Error: Could not force BPDU migration check on this port.

Forceversion for the switch must be 802.1s or 802.1w. Explanation User attempt to enable protocol-migration on 802.1d mode. Recommended Action Change the spanning mode to 802.1s (MSTP) or 802.1w

(RSTP).


3.2.14 Link-State

This section contains the Link-State module messages. Error Message ERROR! Interface is used in other group or function. Explanation User attempt to use a interface that already used in other

Link-State group or other functions. Recommended Action Make sure the interface is not used by other group or other

functions.

Error Message ERROR! This interface is not the upstream of this group. Explanation User attempt to remove a invalid interface from Link-State

upstream. Recommended Action Make sure the interface is in Link-State upstream.

Error Message ERROR! This interface is not the downstream port of this group. Explanation User attempt to remove a invalid interface from Link-State

downstream. Recommended Action Make sure the interface is in Link-State downstream.

Error Message ERROR! Please disable this group first. Explanation User attempt to modify a enabled Link-State group. Recommended Action Make sure the Link-State group is disabled before modification.

Error Message This logical interface is a member of downstream!!! Explanation User attempt to assign a logical interface to the upstream

member of Link-State group but the logical interface has been assigned to the downstream member of Link-State group.

Recommended Action Remove the logical interface from downstream of the Link-State, and assign the logical interface to the upstream.

Error Message This logical interface is a member of upstream!!! Explanation User attempt to assign a logical interface to the downstream

member of Link-State group but the logical interface has been assigned to the upstream member of Link-State group.

Recommended Action Remove the the logical interface from upstream of the Link-State, and assign the logical interface to the downstream member. # Only port-channel interface with internal ports will be allowed to be set to downstream member.


Error Message Port-channel interface with internal ports can't be set Upstream!!!Explanation User attempt to use por-channel interface with internal ports

(downlink port-channel) for Link-State upstream. Recommended Action Don’t use downlink port-channel interface for Link-State

upstream. The port-channel interface with internal member ports is just allowed to be set to the downstream of the Link-State group.

Error Message This function is not available to this port!!! Explanation User attempt to use invalid port for Link-State function. Recommended Action Make sure use external port for Link-State upstream and use

internal port for Link-State downstream. The port-channel interface with internal port members (downlink port-channel) is treated as an internal/downlink port and it can be set to the downstream.

Error Message This function is not available to this port!!! Explanation User attempt to use invalid port for Link-State function. Recommended Action Make sure use external port for Link-State upstream and use

internal port for Link-State downstream. The downlink port-channel is treated as an internal/downlink port and it can be set to the downstream.

Error Message Link state group can't be created Explanation User attempt to create a Link state group but failed. Recommended Action Make sure the number of Link state group doesn’t reach

maximum. The maximum 6 groups are supported in the non-stackable unit, and 32 groups are supported in stackable unit.

Error Message Group is not exist. Explanation User attempt to enter a non-exist group name. Recommended Action Make sure the group name is exist.

Error Message Incorrect input! Use 'link state group enable <1-32>'. Explanation User input incomplete command. Recommended Action Use 'link state group enable <1-32>'.

Error Message Incorrect input! Use 'no link state group enable <1-32>'. Explanation User input incomplete command. Recommended Action Use 'no link state group enable <1-32>'.


Error Message Incorrect input! Use 'no link state group [enable] <1-32>' Explanation User input incomplete command. Recommended Action Use 'no link state group [enable] <1-32>'

Error Message I Incorrect input! Use 'show link state'. Explanation User input incorrect command. Recommended Action Use 'show link state'.


3.2.15 Port-backup

This section contains the Port-backup module messages. Error Message ERROR! This feature is not support for downlink port-channel. Explanation User attempt to use a downlink port-channel to Port-backup. Recommended Action Make sure the interface is not downlink port-channel.

Error Message ERROR! This feature is not support for port-channel member. Explanation User attempt to use a port-channel member interface to

Port-backup. Recommended Action Make sure the interface is not port-channel member.

Error Message ERROR! This interface is used by other group or function. Explanation User attempt to use an interface that already used in other

port-backup group. Recommended Action Make sure the interface is not used by other groups.

Error Message ERROR! This interface is not the backup of this group. Explanation User attempt to remove a invalid interface from port-backup

backup. Recommended Action Make sure the interface is port-backup backup.

Error Message ERROR! This interface is not the active of this group. Explanation User attempt to remove a invalid interface from port-backup

active. Recommended Action Make sure the interface is port-backup active.

Error Message Disable this group first. Explanation User attempt to modify a enabled port-backup group. Recommended Action Make sure the port-backup group is disabled before

modification.

Error Message This function is not available to this port!!! Explanation User attempt to use invalid port for port-backup function. Recommended Action Make sure the external ports are used for port-backup.


Error Message port pair should be configured before enabling this group. Explanation User attempt to enable a port backup group but either active or

backup port is not configured. Recommended Action Make sure the port backup group is well configured.

Error Message Port backup group can't be created Explanation User attempt to create a port backup group but failed. Recommended Action Make sure the number of port backup group doesn’t reach

maximum.

Error Message Group is not exist. Explanation User attempt to enter a non-exist group name. Recommended Action Make sure the group name is exist.

Error Message Incorrect input! Use 'port-backup group [enable] <1-32>'. Explanation User input incomplete command. Recommended Action Use 'port-backup group [enable] <1-32>'.

Error Message Incorrect input! Use 'no port-backup group [enable] <1-32>' Explanation User input incomplete command. Recommended Action Use 'no port-backup group [enable] <1-32>'

Error Message Incorrect input! Use 'port-backup group <1-32> {active |

backup}'. Explanation User input incomplete command. Recommended Action Use 'port-backup group <1-32> {active | backup}'.

Error Message Incorrect input! Use 'no port-backup group [enable] <1-32>' Explanation User input incomplete command. Recommended Action Use 'no port-backup group [enable] <1-32>'


3.2.16 MAC Filter

This section contains MAC Filter module messages. Error Message Error! Attempting to exceed the maximum number of MAC

Filters. Explanation The table of MAC Filter is full. Recommended Action User can only input 20 entries of MAC Filter.

Error Message The MAC Filter already exists. Explanation User input a mac-address that had been created in the table. Recommended Action Correct the mac-address.

Error Message This Filter does not exist. Explanation User input a MAC Filter that had NOT been created in the table. Recommended Action Create the MAC Filter table first.

Error Message Incorrect input! Use 'macfilter [addsrc all] <macaddr> <vlanid>'. Explanation User input incomplete command. Recommended Action Use 'macfilter [addsrc all] <macaddr> <vlanid>'.

Error Message Incorrect input! Use 'no macfilter [addsrc all] <macaddr>

<vlanid>'. Explanation User input incomplete command. Recommended Action Use 'no macfilter [addsrc all] <macaddr> <vlanid>'.

Error Message Incorrect input! Use 'macfilter addsrc <macaddr> <vlanid>'. Explanation User input incomplete command. Recommended Action Use 'macfilter addsrc <macaddr> <vlanid>'.

Error Message Incorrect input! Use 'no macfilter addsrc <macaddr> <vlanid>'. Explanation User input incomplete command. Recommended Action Use 'no macfilter addsrc <macaddr> <vlanid>'.

Error Message Incorrect input! Use 'macfilter addsrc all <macaddr> <vlanid>'. Explanation User input incomplete command. Recommended Action Use 'macfilter addsrc all <macaddr> <vlanid>'.


Error Message Incorrect input! Use 'no macfilter addsrc all <macaddr>

<vlanid>'. Explanation User input incomplete command. Recommended Action Use 'no macfilter addsrc all <macaddr> <vlanid>'.


3.3 Group Administration (IBP)

3.3.1 Uplink Set

This section contains the Uplink-Set module messages. Error Message Incorrect input! Use 'uplink-set <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘uplink-set <uplinkSetName>'.

Error Message Incorrect input! Use 'no uplink-set <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no uplink-set <uplinkSetName>'.

Error Message Incorrect input! Uplink Set name can not more than 32

characters. Explanation User input an Uplink set name, the length of name exceeded 32

characters. Recommended Action The length of the Uplink set name should less than 32

characters.

Error Message Incorrect input! Uplink Set name must contain alphanumeric

characters only. Explanation User input non alphanumeric characters for Uplink set name. Recommended Action Use alphanumeric characters for the Uplink set name.

Error Message Incorrect input! Uplink Set <uplinkSetName> has been used!! Explanation User try to create a new Uplink Set that has already exist in the

system. Recommended Action Use the correct Uplink Set name for this function.

Error Message Incorrect input! Uplink Set <uplinkSetName> does not exist!! Explanation User input an Uplink set name, but the Uplink set doesn’t exist. Recommended Action Use the correct Uplink set name for this function.

Error Message ERROR: Uplink Set table is full. Explanation User try to create a new Uplink Set, but the Uplink Set table has

reached the maximum.


Recommended Action The maximum Uplink Set is 30, please check the Uplink Set setting.

Error Message ERROR: Uplink Set name <uplinkSetName> is not allowed to delete.

Explanation User try to delete a Uplink Set that has associated with a Port Group.

Recommended Action User should break association with the Port Group first, and then delete the Uplink Set.

Error Message Incorrect input! Use 'show uplink-set [<uplinkSetName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show uplink-set [<uplinkSetName>]'.

Error Message ERROR: Could not set internal port <intIfNum> on Uplink Set

port. Explanation User try to add an internal port to the Uplink Set. Recommended Action Internal port doesn’t support Uplink Set function. Internal port

should be configured as the member of Port Group, VLAN port group, service LAN or service VLAN.

Error Message Error: Operation not possible - Port speed does not match LAG

speed or does not full-duplex. Explanation User try to add an external port to the Uplink Set, but the speed

capability of the external port doesn’t match the setting of this Uplink Set member ports.

Recommended Action User should check the speed capability of the external port to match the Uplink Set members.

Error Message Add interface <intIfNum> to Uplink Set <uplinkSetName> failure!Explanation User try to add an external port to the Uplink Set, but the

member port of the Uplink Set has reached the maximum (8 ports).

Recommended Action User should move one member out of the Uplink Set, and then add this external port to the Uplink Set.


3.3.2 Port-Group

This section contains the Port-Group module messages. Error Message Incorrect input! Use 'port-group <portGroupName>

[<uplinkSetName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-group <portGroupName>

[<uplinkSetName>]'.

Error Message Incorrect input! Use 'no port-group <portGroupName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no port-group <portGroupName>'.

Error Message Incorrect input! Port Group name can not more than 32

characters. Explanation User input a Port Group name, the length of name exceeded 32

characters. Recommended Action The length of the Port Group name should less than 32

characters.

Error Message Incorrect input! Port Group name must contain alphanumeric

characters only. Explanation User input non alphanumeric characters for Port Group name. Recommended Action Use alphanumeric characters for the Port Group name.

Error Message Incorrect input! Port Group <portGroupName> has been used!! Explanation User try to create a new Port Group that has already exist in the

system. Recommended Action Use the correct Port Group name for this function.

Error Message Incorrect input! Port Group <portGroupName> does not exist!! Explanation User input a Port Group name, but the Port Group doesn’t exist. Recommended Action Use the correct Port Group name for this function.

Error Message ERROR: Port Group table is full. Explanation User try to create a new Port Group, but the Port Group table

has reached the maximum. Recommended Action The maximum Port Group is 36, please check the Port Group

setting.


Error Message ERROR: Uplink Set <uplinkSetName> has been used by other module.

Explanation User input an Uplink set name to associate with a Port Group, but the Uplink set has used for other groups.

Recommended Action Use another Uplink set for this Port Group.

Error Message ERROR: Port Group name <portGroupName> is not allowed to delete.

Explanation User try to delete a Port Group that is created by system. Recommended Action The system created Port Group could not be deleted, please use

the correct Port Group name for this function.

Error Message Incorrect input! Use 'show port-group [<portGroupName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show port-group [<portGroupName>]'.

Error Message Incorrect input! Use 'port-group <portGroupName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-group <portGroupName>'.

Error Message ERROR: Could not set external port <intIfNum> on port group. Explanation User try to add an external port to the Port Group. Recommended Action External port doesn’t support Port Group function. External port

should use Uplink set.

Error Message ERROR: This function is not allowed on port-channel members. Explanation User try to add a port-channel member port to a Port Group. Recommended Action The interface should move out from the port-channel and then

add to the Port Group.

Error Message ERROR: Interface <intIfNum> is already member of a port

group. Explanation User try to add a port to the Port Group, but the port has joined

this Port Group already. Recommended Action Use the correct Port Group for this function.


3.3.3 VLAN Port-Group

This section contains the VLAN Port-Group module messages.

Error Message Incorrect input! VLAN port group name can not more than 32

characters. Explanation User input incorrect command. Recommended Action VLAN port group name can not more than 32 characters.

Error Message Incorrect input! VLAN port group name must contain

alphanumeric characters only. Explanation User input non alphanumeric characters for VLAN port group

name. Recommended Action Use alphanumeric characters for the VLAN port group name.

Error Message Incorrect input! VLAN port group <vlanGroupName> does not

exist! Explanation User input a VLAN port group name, but the VLAN port group

doesn’t exist Recommended Action Use the correct VLAN port group name for this function.

Error Message Incorrect input! Use 'vlan-group <vlanGroupName> <vlanID>

<uplinkSetName>'. Explanation User input incorrect command. Recommended Action Use 'vlan-group <vlanGroupName> <vlanID>

<uplinkSetName>'.

Error Message Incorrect input! Use 'no vlan-group <vlanGroupName>'. Explanation User input incorrect command. Recommended Action Use 'no vlan-group <vlanGroupName>'.

Error Message Incorrect input! VLAN port group name can not more than 32

characters. Explanation User input a VLAN port group name, the length of name

exceeded 32 characters. Recommended Action VLAN port group name can not more than 32 characters.

Error Message Incorrect input! VLAN port group <vlanGroupName> has been

used! Explanation User try to create a new VLAN port group that has already exist

in the system. Recommended Action Use the correct VLAN port group name for this function.


Error Message Incorrect input! VLAN port group <vlanGroupName> does not

exist! Explanation User input a VLAN port group name, but the VLAN port group

doesn’t exist. Recommended Action Use the correct VLAN port group name for this function.

Error Message ERROR: Can't set VLAN port group with the same VLAN ID

<vlanId> on the <vlanGroupName>. Explanation Can't set VLAN port group with the same VLAN ID used by a

exist VLAN port group. Recommended Action Use other VLAN ID for your VLAN port group.

Error Message Uplink Set <uplinkSetName> has been used by other module." Explanation This Uplink Set has been used by other module." Recommended Action Use other uplink set for your group.

Error Message Incorrect input ! VLAN port group <vlanGroupName> has been

used!! Explanation VLAN port group name has been used!! Recommended Action Use other group name for your VLAN port group.

Error Message ERROR: VLAN port group table is full. Explanation User try to create a new VLAN port group, but the VLAN port

group table has reached the maximum. Recommended Action The maximum VLAN port group is 30, please check the VLAN

port group setting.

Error Message Incorrect input! Use 'vlan-group-nativeVLAN

<vlanGroupName>'. Explanation User input incorrect command. Recommended Action .Use 'vlan-group-nativeVLAN <vlanGroupName>'.

Error Message Incorrect input! Use 'no vlan-group-nativeVLAN

<vlanGroupName>'. Explanation User input incorrect command. Recommended Action Use 'no vlan-group-nativeVLAN <vlanGroupName>'.


3.3.4 Service LAN

This section contains the Service LAN module messages. Error Message Incorrect input! Use 'svc-lan <svcLanName> <vlanID>

<uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘svc-lan <svcLanName> <vlanID>

<uplinkSetName>'.

Error Message Incorrect input! Use 'no svc-lan <svcLanName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no svc-lan <svcLanName>'.

Error Message Incorrect input! Service LAN name can not more than 32

characters. Explanation Incomplete command for this function. Recommended Action Use complete command ‘

Error Message Incorrect input! Service LAN name must contain alphanumeric

characters only. Explanation User input non alphanumeric characters for Service LAN name. Recommended Action Use alphanumeric characters for the Service LAN name.

Error Message Incorrect input! Service LAN <svcLanName> has been used!! Explanation User try to create a new Service LAN that has already exist in

the system. Recommended Action Use the correct Service LAN name for this function.

Error Message Incorrect input! Service LAN <svcLanName> does not exist! Explanation User input an Service LAN name, but the Service LAN doesn’t

exist. Recommended Action Use the correct Service LAN name for this function.

Error Message ERROR: Service LAN table is full. Explanation User try to create a new Service LAN, but the Service LAN table

has reached the maximum. Recommended Action The maximum Service LAN is 10, please check the Service LAN

setting.


Error Message Incorrect input! Use 'show svc-vlan [<svcLanName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show svc-vlan [<svcLanName>]'.

Error Message Incorrect input! Use 'svc-lan <svcLanName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘svc-lan <svcLanName>'.

Error Message ERROR: Could not set external port <intIfNum> on Service LAN

port. Explanation User try to add an external port to the Service LAN. Recommended Action External port doesn’t support Service LAN function. External port

should use Uplink set.

Error Message ERROR: Interface <intIfNum> has been used!! Explanation User try to add a port to the Service LAN, but this port has been

added in another Service LAN or Service VLAN. Recommended Action User should move this port out of the original Service LAN or

Service VLAN, and then add this port to this Service LAN.


3.3.5 Service VLAN

This section contains the Service VLAN module messages.

Error Message Incorrect input! Use 'svc-vlan <svcVlanName> <vlanID>

<uplinkSetName>'. Explanation User input incomplete command. Recommended Action Use 'svc-vlan <svcVlanName> <vlanID> <uplinkSetName>'.

Error Message Incorrect input! Use 'no svc-vlan <svcVlanName>'. Explanation User input incomplete command. Recommended Action Use 'no svc-vlan <svcVlanName>'.

Error Message Incorrect input! Service VLAN name can not more than 32

characters. Explanation User input over 32 characters for Service VLAN name. Recommended Action Maximum 32 characters can be used for Service VLAN name.

Error Message Incorrect input! Service VLAN name must contain alphanumeric

characters only. Explanation User input non-alphanumeric characters for Service VLAN

name. Recommended Action Use alphanumeric characters only for Service VLAN name.

Error Message Incorrect input! Service VLAN <svcVlanName> has been used!! Explanation User attempt to create an exist Service VLAN name. Recommended Action Use other non-exist name for Service VLAN name.

Error Message Incorrect input! Service VLAN <svcVlanName> does not exist!! Explanation User attempt to delete a non-exist Service VLAN name. Recommended Action Make sure the Service VLAN name is exist.

Error Message ERROR: Can't set Service VLAN group with the same VLAN ID

<vlanId> on the <svcVlanName>. Explanation User attempt to set Service VLAN group with the same VLAN ID

of other groups. Recommended Action Use other VLAN ID for your service VLAN group.


Error Message ERROR: Uplink Set <uplinkSetName> has been used by other

module. Explanation User attempt to set Service VLAN group on the Uplink Set has

been used by other function, ex:Service LAN. Recommended Action Uplink Set can only be used for one function, please create other

Uplink Set or remove it from the other module.

Error Message ERROR: Service VLAN table is full. Explanation User attempt to create a Service VLAN group when table is full. Recommended Action Maximum 128 Service VLAN groups can be created.

Error Message ERROR: Could not set external port 'x/x/x' on Service VLAN

port. Explanation User attempt to set external port on Service VLAN. Recommended Action Only internal port can be set on Service VLAN.

Error Message Add interface <intIfNum> to Service VLAN <svcVlanName>

failure! Explanation User attempt to set the same Service VLAN on the interface. Recommended Action Use other Service VLAN to set.


3.3.6 Lock

This section contains the Lock module messages. Error Message Incorrect input! Use 'lock <lock_identifier> [EXCLUSIVE]'. Explanation User input incorrect command. Recommended Action Use 'lock <lock_identifier> [EXCLUSIVE]'.

Error Message Incorrect input! Use 'no lock {<lock_identifier>|all}'. Explanation User input incorrect command. Recommended Action Use 'no lock {<lock_identifier>|all}'.

Error Message Incorrect input! Lock identifier can not more than %d characters. Explanation User input incorrect command. Recommended Action Lock identifier can not more than 32 characters.

Error Message Incorrect input! Lock identifier must contain alphanumeric

characters only. Explanation The input lock identifier contains non-alphanumeric characters. Recommended Action lock identifier must contain alphanumeric characters only.

Error Message Incorrect input! Lock identifier <identifier> has been used! Explanation User input Lock identifier has been used. Recommended Action Use other lock identifier.

Error Message Lock identifier can not be 'ALL'. Explanation User input Lock identifier used ALL. Recommended Action Lock identifier can not be 'ALL'.

Error Message Lock identifier entry is full!! Explanation User input Lock identifier is full. Recommended Action Lock identifier entry is full!!

Error Message Incorrect input! Lock identifier <identifier> does not exist!! Explanation Users delete Lock identifier which does not exist. Recommended Action Use correct lock identifier for this function.


Error Message Set Lock identifier ‘<identifier>’ EXCLUSIVE failure!! Normal lock

had already configured. Explanation User attempt to set EXCLUSIVE lock identifier, but switch has

already configured with this lock identifier. Recommended Action Use command ‘lock_reset’ to clear lock setting, and then use

command ‘lock <lock_identifier> EXCLUSIVE’ to create lock identifier.

Error Message Incorrect input! Use 'lock_message {<message_string>

|default}'. Explanation User does not input lock_message string. Recommended Action Use 'lock_message {<message_string> |default}.

Error Message Incorrect input! message string can not more than 512

characters. Explanation User input message string can not more than 512 characters. Recommended Action The message string can not more than 512 characters.


3.3.7 Port

This section contains the port module messages. Error Message Incorrect input! Use 'description <string>'. Explanation User input incomplete command . Recommended Action Use 'description <string>'.

Error Message Maximum allowed length of Description string is 64 characters. Explanation User input description string over 64 characters. Recommended Action Maximum 64 characters can be allowed for interface description.

Error Message In order for physical mode configurations to take effect,

auto-negotiate must be disabled. Use 'no negotiate' command to disable.

Explanation User attempt to change speed of the port which is working on auto-negotiate mode.

Recommended Action Disable auto-negotiate before changing the port speed.

Error Message Incorrect input! Use 'channel-group <logical logical slot/port>'. Explanation User input incomplete command. Recommended Action Use 'channel-group <logical logical slot/port>'.

Error Message Incorrect input! Use 'delete-channel-group <logical logical

slot/port>'. Explanation User input incomplete command. Recommended Action Use 'delete-channel-group <logical logical slot/port>'.

Error Message Incorrect input! Use 'mtu <1518-9216>'. Explanation User input incomplete command. Recommended Action Use 'mtu <1518-9216>'.

Error Message Incorrect input! Use 'capabilities {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'capabilities {10|100|1000 half-duplex|full-duplex}'.


Error Message Incorrect input! Use 'no capabilities {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'no capabilities {10|100|1000 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'capabilities all {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'capabilities all {10|100|1000 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'no capabilities all {10|100|1000

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'no capabilities all {10|100|1000 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'speed-duplex {10|100

half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'speed-duplex {10|100 half-duplex|full-duplex}'.

Error Message Incorrect input! Use 'speed-duplex all {{100|10}

{half-duplex|full-duplex}'. Explanation User input incomplete command. Recommended Action Use 'speed-duplex all {{100|10} {half-duplex|full-duplex}'.

Error Message This function is not available to this port!!! Explanation Only external ports can be changed speed. Internal ports always

fix on 1G speed. Recommended Action User can’t change the speed for the internal ports.

Error Message Incorrect input! This interface is a member of channel group. Explanation User attempt to enable flowcontrol on a member port of channel

group. Recommended Action User is not allowed to enable flow control on port-channel

member port. Please enable the flow control on the port-channel interface.

Error Message Incorrect input! Use 'show interface status {<unit/slot/port> | all}'. Explanation User input incomplete command . Recommended Action Use 'show interface status {<unit/slot/port> | all}'.


Error Message ERROR: syntax error, command: switchport broadcast all

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport broadcast all packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport unicast all

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport unicast all packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport multicast all

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport multicast all packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport broadcast

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport broadcast packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport unicast

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport unicast packet-rate <1-4>'.

Error Message ERROR: syntax error, command: switchport multicast

packet-rate <level> Explanation User input incomplete command . Recommended Action Use 'switchport multicast packet-rate <1-4>'.

Error Message ERROR: syntax error, command: no switchport broadcast all Explanation User input incomplete command . Recommended Action Use command ‘no switchport broadcast all.’

Error Message ERROR: syntax error, command: no switchport unicast all Explanation User input incomplete command . Recommended Action Use command ‘no switchport unicast all’


Error Message ERROR: syntax error, command: no switchport multicast all Explanation User input incomplete command . Recommended Action Use command ‘no switchport multicast all’

Error Message Incorrect input! Use 'port-monitor session <session-id> {mode |

source interface <slot/port> [tx | rx] | destination interface <slo t/port> }'.

Explanation User input incomplete command. Recommended Action Use 'port-monitor session <session-id> {mode | source interface

<slot/port> [tx | rx] | destination interface <slo t/port> }'.

Error Message Incorrect input! Use 'no monitor [session <session-id> [{mode |

source interface <slot/port> | destination interface}]]'. Explanation User input incomplete command. Recommended Action Use 'no monitor [session <session-id> [{mode | source interface

<slot/port> | destination interface}]]'.

Error Message This interface can not be configured as destination port. Explanation User attempt to set the port-channel interface to be destination

port. Recommended Action User can only set the normal ports to be destination port.

Error Message Probe port must be reset before re-configuring it. Explanation User attempt to change the destination port. Recommended Action User must delete the original destination port and then set a new

one.

Error Message Interface is not configured. Explanation User attempt to delete the destination port but it was not created.Recommended Action Make sure the destination had been created.


3.3.8 IGMP Snooping


Error Message Incorrect input! Use 'igmp-snooping <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'igmp-snooping <uplinkSetName>'.

Error Message Incorrect input! Use 'no igmp-snooping <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no igmp-snooping <uplinkSetName>'.

Error Message Incorrect input! Use 'show igmp-snooping [<uplinkSetName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command 'show igmp-snooping

[<uplinkSetName>]'.


3.3.9 Port-Channel

This section contains the Port-Channel module messages. Error Message Incorrect input! Use 'load-balance

{dst-ip|dst-mac|src-dst-ip|src-dst-mac|src-ip|src-mac}'. Explanation Incomplete command for this function. Recommended Action Use complete command Use 'load-balance


Error Message Invalid interface <IntIfNum>, is not a port-channel interface. Explanation The interface is not a port-channel interface. Recommended Action Use correct port-channel interface.

Error Message Incorrect input! Use 'no port-channel load-balance all'. Explanation Incomplete command for this function. Recommended Action Use 'no port-channel load-balance all'.

Error Message Cannot change the auto-negotiate mode of a port-channel

member. Explanation The port-channel member port can NOT be changed to

auto-negotiate mode . Recommended Action Use this command only on normal port.

Error Message Could not create. Maximum number of port-channels (64)

reached. Explanation User creates more than 64 port-channel groups. Recommended Action User just can create maximum 64 port-channel groups.

Error Message Error: Characters in the port-channel name must be

alphanumeric and can contain dashes or underscores. Explanation User input a port-channel name with non-alphanumeric

characters. Recommended Action Use alphanumeric and dashes or underscores for port-channel

name.

Error Message No port-channels exist. Explanation There is no port-channel exist. Recommended Action Create a port-chnnel first.


Error Message Ports cannot be added to disabled port-channels. Explanation User attempt to add a member to a disabled port-channel. Recommended Action Enable the port-channel before add member ports.

Error Message Ports being added to a port-channel must not be participating in

MAC Filtering. Explanation User attempt to add a interface to a port-channel, but the

interface has been set with MAC filter function. Recommended Action Use command ‘no macfilter addsrc <macaddr>’ to remove the

MAC Filter setting first, and then use command ‘channel-group <unit/slot/port>’ to add interface to the port-channel.

Error Message Could not create. This port-channel name already exists. Explanation User create a port-channel name that already exists. Recommended Action Use another port-channel name.

Error Message [slot/port] is not a configured port-channel. Explanation User try to display the port-channel information for

non-port-channel interface. Recommended Action Use correct port-channel interface slot/port for this command.

Error Message Port-channel name must be less than 16 characters. Explanation User attempt to crate a port-channel name is over 15 characters.Recommended Action Configure port-channel name within 15 characters.

Error Message Incorrect input! Use 'port-channel load-balance all

{dst-ip|dst-mac|src-dst-ip|src-dst-mac|src-ip|src-mac}'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-channel load-balance all


Error Message Incorrect input! Use 'port-channel name {<logical slot/port> | all}

<name>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-channel name {<logical slot/port> |

all} <name>'.

Error Message Port-channel name is too long. Explanation User attempt to rename a port-channel name over 15

characters. Recommended Action Configure port-channel name within 15 characters.


Error Message Incorrect input! Use 'port-channel <name>'. Explanation User input incomplete command. Recommended Action Use 'port-channel <name>'.

Error Message Incorrect input! Use 'no port-channel {<logical unit/slot/port> |

all}'. Explanation User input incomplete command. Recommended Action Use 'no port-channel {<logical unit/slot/port> | all}'.

Error Message Incorrect input! Use 'port-channel adminmode all'. Explanation User input incomplete command. Recommended Action Use 'port-channel adminmode all'.

Error Message Incorrect input! Use 'no port-channel adminmode all'. Explanation User input incomplete command. Recommended Action Use 'no port-channel adminmode all'.

Error Message Incorrect input! Use 'port-channel linktrap {<logical unit/slot/port>

| all}'. Explanation User input incomplete command. Recommended Action Use 'port-channel linktrap {<logical unit/slot/port> | all}'.

Error Message Incorrect input! Use 'no port-channel linktrap {<logical slot/port> |

all} '. Explanation User input incomplete command. Recommended Action Use 'no port-channel linktrap {<logical slot/port> | all} '.

Error Message Incorrect input! Use 'delete-channel-group <logical slot/port> all' Explanation User input incomplete command. Recommended Action Use 'delete-channel-group <logical slot/port> all'


Error Message Incorrect input! Use 'lacp <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'lacp <uplinkSetName>'.

Error Message Incorrect input! Use 'no lacp <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'no lacp <uplinkSetName>'.

Error Message Incorrect input! Use 'show lacp [<uplinkSetName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command 'show lacp [<uplinkSetName>]'.

Error Message Incorrect input! Use 'show lacp interface {<unit/slot/port> | all}'. Explanation Incomplete command for this function. Recommended Action Use complete command ' show lacp interface {<unit/slot/port> |

all}'.

Error Message ERROR: Invalid interface - %s Explanation User try to configure or display information of an interface, but

the interface not support this function. Recommended Action Use the correct interface for this function.


3.3.10 Link-State

This section contains the Link-State module messages.

Error Message Incorrect input! Use 'linkstate <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘linkstate <uplinkSetName>'.

Error Message Incorrect input! Use 'no linkstate <uplinkSetName>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no linkstate <uplinkSetName>'.

Error Message Incorrect input! Use 'show linkstate [<uplinkSetName>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show linkstate [<uplinkSetName>]'.


3.3.11 Port-backup

This section contains the Port-backup module messages.

Error Message Incorrect input! Use 'port-backup <uplinkSetName>

[failback-time <value>]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘port-backup <uplinkSetName>

[failback-time <value>]'.

Error Message Incorrect input! Use 'no port-backup <uplinkSetName>

[failback-time]'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no port-backup <uplinkSetName>

[failback-time]'.

Error Message Incorrect input! Use 'show port-backup [<uplinkSetName> [status] | status ] '.

Explanation Incomplete command for this function. Recommended Action Use complete command ‘show port-backup [<uplinkSetName>

[status] | status ] '.

Error Message ERROR: Could not set internal port '%s' on Port Backup port. Explanation User try to add an internal port to the backup port. Recommended Action Internal port doesn’t support the Port Backup function.

Error Message Error: It is not allowed to configure the last member of active port

to backup port !! Explanation User try to change the last active port to backup port. Recommended Action The Uplink set should have at least one active port; user can’t

change all member ports to the backup ports.

Error Message Set Uplink Set '%s' backup failure!! Explanation User try to add an interface to backup port, but the interface is

not belong to any Uplink set. Or the interface is a logical interface not a physical interface.

Recommended Action Use a physical interface that has added to Uplink set for this function.


3.4 Security

3.4.1 Port Access Control

This section contains Port Access Control module messages.

Error Message Incorrect input! Use 'dot1x max-req <count>'. Explanation Incomplete command for this function. Recommended Action Use 'dot1x max-req <count>'.

Error Message Incorrect input! Use 'show dot1x [{summary <%s|all>} | {detail

<%s>} |{statistics <%s>}]' Explanation Incomplete command for this function. Recommended Action Use complete command

Error Message Incorrect input! Use 'show dot1x summary <%s|all>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show dot1x summary <slot/port>'

Error Message Incorrect input! Use 'show dot1x detail <%s>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show dot1x detail <slot/port>’

Error Message Incorrect input! Use 'show dot1x statistics <%s>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show dot1x statistics <slot/port>’

Error Message Incorrect input! Use 'show dot1x users <%s>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show dot1x users <slot/port>’

Error Message Incorrect input! \r\nUse 'dot1x port-control <auto |

force-authorized | force-unauthorized>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘dot1x port-control <auto |

force-authorized | force-unauthorized>'


Error Message Incorrect input! \r\nUse 'dot1x port-control all <auto |

force-authorized | force-unauthorized>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘dot1x port-control all <auto |

force-authorized | force-unauthorized>'

Error Message Incorrect input! Use 'dot1x timeout quiet-period <1-65535>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘dot1x timeout quiet-period <0-65535>’

Error Message Incorrect input! Use 'dot1x timeout tx-period <1-65535>'. Explanation Incomplete command for this function. Recommended Action Use complete command ' dot1x timeout tx-period <1-65535>'

Error Message Incorrect input! Use 'dot1x timeout supp-timeout <1-65535>'. Explanation Incomplete command for this function. Recommended Action Use complete command ' dot1x timeout supp-timeout

<1-65535>'

Error Message Incorrect input! Use 'dot1x timeout server-timeout <1-65535>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'dot1x timeout server-timeout

<1-65535>'

Error Message Incorrect input! Use 'dot1x timeout reauth-period <1-65535>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘dot1x timeout reauth-period

<1-65535>'

Error Message Incorrect input! Use '[no] dot1x user <user> <<intIfNum> | all>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘dot1x user <user> <slot/port | all>'


Error Message Incorrect input! Use 'dot1x timeout {{quiet-period <seconds>} |

{reauth-period <seconds>} | {server-timeout <seconds>} | {supp-timeout <seconds>} | {tx-period <seconds>}}'.

Explanation Incomplete command for this function. Recommended Action Use complete command ‘dot1x timeout {{quiet-period

<seconds>} | {reauth-period <seconds>} | {server-timeout <seconds>} | {supp-timeout <seconds>} | {tx-period <seconds>}}'

Error Message Incorrect input! Use 'no dot1x timeout { quiet-period |

reauth-period | server-timeout | supp-timeout | tx-period }'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no dot1x timeout { quiet-period |

reauth-period | server-timeout | supp-timeout | tx-period }'

Error Message Incorrect input! Use 'dot1x defaultlogin <listname>' Explanation Incomplete command for this function. Recommended Action Use complete command ' dot1x defaultlogin <listname>'.

Error Message Incorrect input! Use 'dot1x login <user> <listname>' Explanation Incomplete command for this function. Recommended Action Use complete command 'dot1x login <user> <listname>'.

Error Message Invalid User Name Size. Explanation User input a user name that has exceeded 8 characters The

maximum length of user name is 8 characters. Recommended Action Use correct user name for this function.

Error Message Invalid User Name. Explanation User try to add a user to the interface(s) for dot1x function, but

this user doesn’t exist in the system. Recommended Action Use command ‘username <username>’ to create a user, and

use command ‘dot1x user <username> <unit/slot/port | all>’ to add the user to interface(s).

Error Message Invalid Authentication Login List Name. Explanation User attempt to assign a non-exist authentication login list name

for dot1x function. Recommended Action Use command ‘authentication login <listname>’ to create the list

first, and then use command ‘dot1x default-login <listname>’ to assign to dot1x function.


Error Message Incorrect input! Use '[no] dot1x user <user> <%s | all>'. Explanation Incomplete command for this function. Recommended Action Use complete command ' [no] dot1x user <user> <slot/port |

all>'.

Error Message Incorrect input! Use 'clear dot1x statistics <%s | all>'. Explanation Incomplete command for this function. Recommended Action Use complete command 'clear dot1x statistics <slot/port | all>'.


3.4.2 Port Security

This section contains Port Security module messages. Error Message Incorrect input! Use 'port-security violation shutdown'. Explanation User input incomplete command. Recommended Action Use 'port-security violation shutdown'.

Error Message Incorrect input! Use 'port-security max-dynamic <0-600>' Explanation User input incomplete command. Recommended Action Use 'port-security max-dynamic <0-600>'

Error Message Incorrect input! Use 'port-security max-static <0-20>' Explanation User input incomplete command. Recommended Action Use 'port-security max-static <0-20>'

Error Message Incorrect input! Use 'port-security mac-address <mac-addr>

<1-4094>' Explanation User input incomplete command. Recommended Action Use 'port-security mac-address <mac-addr> <1-4094>'

Error Message Incorrect input! Use 'no port-security mac-address <mac-addr>

<1-4094>' Explanation User input incomplete command. Recommended Action Use 'no port-security mac-address <mac-addr> <1-4094>'

Error Message Incorrect input!! Use 'clear port-security dynamic {address

<mac-addr> | interface <unit/slot/port>}'. Explanation User input incomplete command . Recommended Action Use 'clear port-security dynamic {address <mac-addr> |

interface <unit/slot/port>}'.

Error Message Can not support this command on INTERFACE RANGE MODE

!!! Explanation User attempt to configure Port-Security Static MAC address

under interface range mode. Recommended Action Configure Port-Security Static MAC address port by port.


Error Message User Input Error: Invalid MAC Address Explanation User input invalid MAC Address for Port-Security Static MAC

address. Recommended Action Correct the format of MAC Address.

Error Message Could not add MAC address Explanation User attempt to add Port-Security Static MAC address when

table is full. Recommended Action Maximum 20 Static MAC address can be created on a interface.

Error Message Static Limit of 20 reached. No Dynamic Addresses will be

moved. Explanation User attempt to make dynamic MAC addresses to static MAC

addresses of Port-Security function, but the static MAC address table is full.

Recommended Action The maximum static MAC addresses of Port-Security is 20. Please remove the static MAC addressres from the table and add the new static MAC addresses to the Port-Security interface.

Error Message User Input Error: Invalid MAC Address and VLAN ID

Combination Explanation User attempt to delete a non-exist Port-Security Static MAC

address. Recommended Action Make sure the MAC Address is exist.

Error Message Incorrect input! Use 'show port-security dynamic <slot/port>'. Explanation User input incomplete command. Recommended Action Use 'show port-security dynamic <slot/port>'.

Error Message Incorrect input! Use 'show port-security static <slot/port>'. Explanation User input incomplete command. Recommended Action Use 'show port-security static <slot/port>'.

Error Message Incorrect input! Use 'show port-security violation <slot/port>'. Explanation User input incomplete command. Recommended Action Use 'show port-security violation <slot/port>'.


Error Message There are no Dynamically learned MAC addresses. Explanation User attempt to show the Dynamically learned MAC addresses

of a interface, but there is no MAC addresses on this interface. Recommended Action Make sure the port-security function of the interface is enabled

and has learned MAC addresses.

Error Message There are no static MAC addresses. Explanation User attempt to show a interface has no static MAC addresses. Recommended Action Make sure static MAC addresses have been configured on this

interface.


3.4.3 RADIUS

This section contains RADIUS module messages. Error Message Incorrect input! Use 'show radius [servers]' Explanation User input incomplete command . Recommended Action Use 'show radius statistics <ipAddr|ipv6Addr|name>'

Error Message Incorrect input! Use 'show radius accounting [statistics

<ipAddr|ipv6Addr|name>]' Explanation User input incomplete command . Recommended Action Use 'show radius accounting [statistics

<ipAddr|ipv6Addr|name>]'

Error Message No RADIUS servers configured. Explanation User attempt to show RADIUS server but no server has been

created. Recommended Action Create a RADIUS server first.

Error Message Incorrect input! Invalid host name or address. Explanation User input invalid IP address or host name. Recommended Action Correct the format of IP address or host name.

Error Message Incorrect input! Specify a configured RADIUS accounting server.Explanation User attempt to set radius-server key to the RADIUS accouting

server, but the RADIUS server IP address doesn’t exist in the system.

Recommended Action Use exist RADIUS accounting server IP address or use command ‘radius-server host acct <ipAddr|ipv6Addr|hostname>’ to create radius accounting server first, and then use command‘ radius-server key acct <ipAddr|ipv6Addr|hostnamee>’ to set key for radius server.

Error Message Incorrect input! Specify a configured RADIUS server. Explanation User attempt to set radius-server key to RADIUS server, but the

RADIUS server IP address doesn’t exist in the system. Recommended Action Use exist RADIUS server IP address or use command

‘radius-server host auth <ipAddr|ipv6Addr|hostname>’ to create radius server first, and then use command ‘radius-server key auth <ipAddr|ipv6Addr|hostname>’ to set the key for radius server.


Error Message Incorrect input! Invalid the host address. Explanation User input invalid IP address or host name. Recommended Action Correct the format of IP address or host name.

Error Message Error! The accounting server could not be added. Explanation User attempt to configured Radius accounting server but the

server has been configured. Recommended Action Only one accounting server can be configured.

Error Message Error! Enter the correct port number. Explanation User attempt to configured Radius accounting server with invalid

port number. Recommended Action Use port number in the range of 0-65535.

Error Message Error! The accounting server could not be removed. Explanation User attempt to delete an non-exist Radius accounting server. Recommended Action Make sure the Radius accounting server is exist.

Error Message Incorrect input! Use 'radius server dead-time <1-255>'. Explanation User input incomplete command . Recommended Action Use 'radius server dead-time <1-255>'.

Error Message Incorrect input! Use 'radius-server retransmit <retries>' Explanation User input incomplete command . Recommended Action Use 'radius-server retransmit <1-15>'

Error Message Error: Retransmits must be an integer in the range of 1 and 15. Explanation User input invalid value for radius-server retransmit. Recommended Action Use an integer in the range of 1 and 15 for radius-server

retransmit.

Error Message Incorrect input! Use 'radius-server timeout <seconds>' Explanation User input incomplete command . Recommended Action Use 'radius-server timeout <1-30 >'

Error Message Error: Timeout must be an integer in the range of 1 and 30. Explanation User input invalid value for radius-server timeout. Recommended Action Use an integer in the range of 1 and 30. for radius-server

timeout.


Error Message Incorrect input! Use 'radius server dead-time <1-255>'. Explanation User input incomplete command. Recommended Action Use 'radius server dead-time <1-255>'.

Error Message Incorrect input! Use 'radius-server key {auth | acct}

<ipAddr|ipv6Addr|hostname> {0|7} <key-string> ' Explanation User input incomplete command . Recommended Action Use 'radius-server key {auth | acct} <ipAddr|ipv6Addr|hostname>

{0|7} <key-string> '

Error Message Incorrect input! Use 'no radius-server key {auth | acct}

<ipAddr|ipv6Addr|hostname>' Explanation User input incomplete command . Recommended Action Use 'no radius-server key {auth | acct}

<ipAddr|ipv6Addr|hostname>'

Error Message Incorrect input! Use 'radius-server host {auth | acct}

<ipAddr|ipv6Addr|hostname> [<port>]' Explanation User input incomplete command . Recommended Action Use 'radius-server host {auth | acct}

<ipAddr|ipv6Addr|hostname> [<port>]'

Error Message Incorrect input! Use 'no radius-server host {auth | acct}

<ipAddr|ipv6Addr|hostname> [<port>]' Explanation User input incomplete command . Recommended Action Use 'no radius-server host {auth | acct}

<ipAddr|ipv6Addr|hostname> [<port>]'

Error Message Error! The server already exists. Explanation User attempt to create a radius-server with exist IP address. Recommended Action Create radius-server with non-exist IP address.

Error Message Error! Maximum Servers already Configured. Explanation User attempt to create a radius-server when table is full. Recommended Action Maximum 3 servers can be created.

Error Message Error! The server could not be removed. Explanation User attempt to delete a non-exist radius-server. Recommended Action Make sure the server is exist.


Error Message Incorrect input! Use 'radius-server key {auth | acct}

<ipAddr|ipv6Addr|hostname> {0|7} <key-string> ' Explanation User input incomplete command . Recommended Action Use 'radius-server key {auth | acct} <ipAddr|ipv6Addr|hostname>

{0|7} <key-string> '

Error Message Incorrect input! Use 'radius-server primary

<ipAddr|ipv6Addr|hostname>' Explanation User input incomplete command . Recommended Action Use 'radius-server primary <ipAddr|ipv6Addr|hostname>'

Error Message Error! The primary server could not be set. Explanation User attempt to set the primary RADIUS server, but the RADIUS

server IP address doesn’t exist. Recommended Action Use exist radius-server IP address to be the primary server or

use command ‘radius-server host auth <ipAddr|ipv6Addr|hostname>’ to create a radius server first, and then use command ‘radius-server primary <ipAddr|ipv6Addr|hostname>’ to assign primary server.

Error Message Incorrect input! Use 'radius-server msgauth

<ipAddr|ipv6Addr|hostname>' Explanation User input incomplete command . Recommended Action Use 'radius-server msgauth <ipAddr|ipv6Addr|hostname>'

Error Message Incorrect input! Use 'no radius-server msgauth

<ipAddr|ipv6Addr|hostname>' Explanation User input incomplete command . Recommended Action Use 'no radius-server msgauth <ipAddr|ipv6Addr|hostname>'


3.4.4 TACACS+

This section contains TACACS+ module messages. Error Message No TACACS servers configured. Explanation User attempt to show TACACS+ configuration but no server has

been created. Recommended Action Create a TACACS server first.

Error Message Error! Invalid IP address or Host Name. Explanation User input invalid IP address or host name of tacacs server. Recommended Action Correct the IP address or host name of tacacs server.

Error Message Incorrect input! Invalid IP address. IP address should be in

a.b.c.d format where range for a, b, c, and d is 1 - 255. Explanation User input invalid value for TACACS+ server IP address. Recommended Action IP address should be in a.b.c.d format where range for a, b, c,

and d is 1 - 255.

Error Message Error! Unable to add the host. Explanation User attempt to add a TACACS+ server when table is full. Recommended Action Maximum 5 TACACS+ server can be created.

Error Message Error! Unable to delete the host, the IP address or Hostname

does not exist. Explanation User attempt to delete a non-exist TACACS+ server. Recommended Action Make sure the TACACS+ server is exist.

Error Message Error! Range <0 - 65535>. Explanation User input invalid value for TACACS+ serverport number. Recommended Action Use value in range <0 - 65535>.

Error Message Error! Range <1 - 30> seconds. Explanation User input invalid value for TACACS+ server timeout. Recommended Action Use value in range <1 - 30> seconds.

Error Message Error! Use "tacacs key {0|7} <key-string>" to set the global key. Explanation User input invalid value for TACACS+ server global key. Recommended Action Use "tacacs key {0|7} <key-string>" to set the global key.


Error Message Error! Range <0 - 128> characters. Explanation User input invalid value for TACACS+ server key. Recommended Action Use value in range <0 - 128> characters.

Error Message Error! Need 256 characters pre-encrypted key. Explanation User input invalid value for TACACS+ server pre-encrypted key. Recommended Action Use 256 characters pre-encrypted key.

Error Message Error! Range <0 - 65535>. Explanation User input invalid value for TACACS+ server priority. Recommended Action Use value in range <0 - 65535>.


3.4.5 LDAP

This section contains LDAP module messages. Error Message Incorrect input! Use 'ldap ip <ipaddr>'. Explanation User input incomplete command . Recommended Action Use 'radius-server retransmit <1-15>'

Error Message Incorrect input! Use 'ldap port <1-65535>'. Explanation User input incomplete command . Recommended Action Use 'ldap port <1-65535>'.

Error Message Incorrect input! Use 'ldap baseDN <baseDN>'. Explanation User input incomplete command . Recommended Action Use 'ldap baseDN <baseDN>'.

Error Message Incorrect input! Use 'ldap RacNam <RacNam>'. Explanation User input incomplete command . Recommended Action Use 'ldap RacNam <RacNam>'.

Error Message Incorrect input! Use 'ldap RacDomain <RacDomain>'. Explanation User input incomplete command . Recommended Action Use 'ldap RacDomain <RacDomain>'.

Error Message Incorrect input! Use 'show ldap'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘show ldap | begin <LINE>'

Use complete command ‘show ldap | exclude <LINE>’ Use complete command ‘show ldap | include <LINE>’


3.4.6 Access Control Lists

This section contains IP ACL module messages. Error Message Incorrect input! Use 'no access-list <access-list-number>

[<rule_id>]' Explanation User input incomplete command . Recommended Action Use 'no access-list <access-list-number> [<rule_id>]'

Error Message Invalid ACL Name. Name string may include alphabetic,

numeric, dash, dot or underscore characters only. Name must start with a letter and the size of the name string must be less than or equal to 31 characters.

Explanation User input invalid format of IP ACL name. Recommended Action Name string may include alphabetic, numeric, dash, dot or

underscore characters only. Name must start with a letter and the size of the name string must be less than or equal to 31 characters.

Error Message Incorrect input! Use 'ip access-list rename <oldname>

<newname> ' Explanation User input incomplete command . Recommended Action Use ' ip access-list rename <oldname> <newname>'

Error Message Access-list does not exist. Explanation User attempt to rename a non-exist IP access-list. Recommended Action Make sure the IP access-list is exist.

Error Message Access-list already exists. Explanation User attempt to rename the IP access-list to a exist IP access-list

name. Recommended Action To rename a non-exist IP access-list name.

Error Message Incorrect input! The Rule ID <ruleId> is already configured. Explanation User attempt to create a rule with exist Rule ID. Recommended Action Create rule with unused Rule ID.

Error Message Invalid start SrcL4Port number. <select SrcL4Port number

between 0 to 65535> Explanation User attempt to create a rule with invalid SrcL4port number. Recommended Action Create rule with SrcL4Port number between 0 to 65535.


Error Message Invalid keyword. Currently supported values are <domain/echo/ftp/ftpdata/http/smtp/snmp/telnet/tftp/www.>

Explanation User attempt to create a rule with wrong L4port keyword. Recommended Action Create rule with keyword:

<domain/echo/ftp/ftpdata/http/smtp/snmp/telnet/tftp/www.>

Error Message Invalid IP address. Explanation User attempt to create a rule with invalid IP address. Recommended Action Correct the format of IP address.

Error Message ACL does not exist. Explanation User attempt to delete a non-exist ACL. Recommended Action Make sure the ACL is exist.

Error Message The {assign-queue|mirror|redirect} functions are only allowed on

'permit' rule. Explanation User attempt to create a deny rule with

{assign-queue|mirror|redirect} functions. Recommended Action Change rule to permit.

Error Message ACL rule log feature is not supported for a permit action. Explanation User attempt to create a permit rule with log feature. Recommended Action Change rule to deny.

Error Message ERROR: Invalid interface - x/x/x Explanation User attempt to create a rule with invalid interface. Recommended Action Correct the interface.

Error Message Incorrect input! <tosbits> must be two digit hex value in the

range of 00 to ff. Explanation User attempt to create a rule with invalid IP TOS value. Recommended Action <tosbits> must be two digit hex value in the range of 00 to ff.

Error Message Incorrect input! <tosmask> must be two digit hex value in the

range of 00 to ff. Explanation User attempt to create a rule with invalid IP TOS mask. Recommended Action <tosmask> must be two digit hex value in the range of 00 to ff.


Error Message Invalid DSCP value. Explanation User attempt to create a rule with invalid DSCP value.. Recommended Action Use a DSCP value or a DSCP keyword (af11, af12,af13, af21,

af22, af23, af31, af32, af33, af41, af42,af43, be, cs0, cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef).

Error Message Incorrect value! DSCP value must be in the range from 0 to 63. Explanation User attempt to create a rule with invalid DSCP value.. Recommended Action DSCP value must be in the range from 0 to 63.

Error Message Incorrect input! The maximum of 100 ACLs is already

configured. Explanation User attempt to add a access-list when table is full. Recommended Action The maximum of 100 ACLs can be configured.

Error Message Incorrect input! The Rule ID <ruleId> is already configured. Explanation User attempt to add a rule with exist rule ID. Recommended Action Create a rule with non-exist rule ID.

Error Message ACL rules are full. Explanation User attempt to add a rule when table is full. Recommended Action Maximum 10 rules can be created.

Error Message Invalid Wildcard mask. Enter four numbers separated by period

in the range of 0 to 255. Explanation User input invalid wildcard mask. Recommended Action Correct the format of wildcard mask, enter four numbers

separated by period in the range of 0 to 255.

Error Message Incorrect input! <macaddr> must be of type <aa:bb:cc:dd:ee:ff>. Explanation User input invalid MAC address. Recommended Action Correct the format of MAC address, <macaddr> must be of type

<aa:bb:cc:dd:ee:ff>.

Error Message Incorrect input! <macmask> must be of type <aa:bb:cc:dd:ee:ff>.Explanation User input invalid MAC mask. Recommended Action Correct the format of MAC mask, <macmask> must be of type

<aa:bb:cc:dd:ee:ff>.


Error Message Incorrect input! Use 'ip access-group {<1-199>|<name>} in

[<sequence>]'. Explanation User input incomplete command. Recommended Action Use 'ip access-group {<1-199>|<name>} in [<sequence>]'.

Error Message Incorrect input! Use 'no ip access-group {<1-199>|<name>} in '. Explanation User input incomplete command. Recommended Action Use 'no ip access-group {<1-199>|<name>} in '.

Error Message ACL ID does not exist. Explanation User attempt to delete a non-exist ACL. Recommended Action Make sure the ACL is exist.

Error Message Error: ACL and Diffserv can not be used on the same interface in

the same direction. Explanation User attempt to enable ACL & Diffserv on the same interface. Recommended Action User can only enable one function ACL or Diffserv on a interface.

Error Message ACL sequence number is already at limit for this interface and

direction. Explanation User attempt to add ACL to the interface has arrived maximum

ACL sequence number < 4294967295>. Recommended Action Use command “show access-lists” to verify the ACL sequence

number is at limit.

Error Message ACL does not exist or the interface has not been configured with

an ACL. Explanation User attempt to remove a ACL does not assign to this interface. Recommended Action Make sure the ACL has been assigned to the interface.

Error Message The maximum number of ACLs reached for this interface. Explanation User attempt to add ACL to the interface has arrived maximum

number of ACLs. Recommended Action Maximum 9 ACLs can be created for a interface.

Error Message Incorrect input! Use 'show access-lists interface <interface> in'. Explanation User input incomplete command . Recommended Action Use 'show access-lists interface <interface> in'.


Error Message Invalid ACL Name. Name string may include alphabetic,

numeric, dash, dot or underscore characters only. Name must start with a letter and the size of the name string must be less than or equal to 31 characters.

Explanation User input invalid format of MAC ACL name. Recommended Action Name string may include alphabetic, numeric, dash, dot or

underscore characters only. Name must start with a letter and the size of the name string must be less than or equal to 31 characters.

Error Message Incorrect input! The maximum of 100 ACLs is already

configured. Explanation User attempt to create an ACL when table is full. Recommended Action Maximum 100 ACLs can be created.

Error Message MAC Access-list does not exist. Explanation User attempt to delete a non-exist MAC access-list. Recommended Action Make sure the MAC access-list is exist.

Error Message Incorrect input! Use 'mac access-group <name> in

[<sequence>]'. Explanation User input incomplete command. Recommended Action Use 'mac access-group <name> in [<sequence>]'.

Error Message Incorrect input! Use 'no mac access-group <name> in

[<sequence>]'. Explanation User input incomplete command. Recommended Action Use 'no mac access-group <name> in [<sequence>]'.

Error Message MAC Access-list does not exist. Explanation User attempt to assign a non-exist MAC ACL to a interface. Recommended Action Make sure the MAC ACL is exist.

Error Message Error: ACL and Diffserv can not be used on the same interface in

the same direction. Explanation User attempt to enable ACL & Diffserv on the same interface. Recommended Action User can only enable ACL and Diffserv on a interface at the

same time.


Error Message The maximum number of ACLs reached for this interface. Explanation User attempt to add MAC ACL to the interface has arrived

maximum number of MAC ACLs. Recommended Action Maximum 17 MAC ACLs can be created for a interface.

Error Message Unable to remove the specified MAC access-control list from the

specified interface in the inbound direction. Explanation User attempt to remove a MAC ACL does not assign to this

interface. Recommended Action Make sure the MAC ACL has been assigned to the interface.

Error Message No rules have been configured for this MAC ACL Explanation User attempt to show the MAC ACL has no rules. Recommended Action Create a rule for the MAC ACL first.

Error Message Incorrect input! Use 'mac access-list extended rename

<oldname> <newname>' Explanation User input incomplete command. Recommended Action Use 'mac access-list extended rename <oldname> <newname> '

Error Message MAC Access-list already exists. Explanation User attempt to rename a old MAC ACL name to an exist MAC

ACL name. Recommended Action Rename to other non-exist ACL name.

Error Message MAC Access-list does not exist. Explanation User attempt to assign a non-exist MAC Access-list to a

interface. Recommended Action Make sure the MAC Access-list is exist.

Error Message The {assign-queue|mirror|redirect} functions are only allowed on 'permit' rule.

Explanation User attempt to create a deny rule with {assign-queue|mirror|redirect} functions.

Recommended Action Changerule to permit.

Error Message Incorrect input! Ethertype custom value must be from 0x0600 to 0xffff.

Explanation User attempt to create a rule with invalid ethertype custom value.


Recommended Action Ethertype custom value must be from 0x0600 to 0xffff.

Error Message ACL rule log feature is not supported for a permit action. Explanation User attempt to create a permit rule with log feature. Recommended Action Change rule to deny.

Error Message ERROR: Invalid interface format. Must use format -

<unit/slot/port> Explanation User attempt to create a rule with invalid interface format. Recommended Action Correct the format of interface to <unit/slot/port>.

Error Message Maximum rule id reached. Please create rule with rule id <1 to

10> Explanation User attempt to add a rule with rule ID out of range <1-10>. Recommended Action Please create rule with rule ID <1 to 10>

Error Message ACL rules are full. Explanation User attempt to add a rule when table is full. Recommended Action Maximum 10 rules can be created.


3.4.7 IP Filter

This section contains IP Filter module messages.

Error Message Incorrect input! Invalid IP Address. Explanation User input invalid IP address. Recommended Action Correct the format of IP address.

Error Message Manegement IP Filter Address Set Failed. Explanation User attempt to create IP Filter, but the table is full or the host IP

address has been created. Recommended Action Maximum 5 hosts can be created.

Error Message Manegement IP Filter Address Delete Failed. Explanation User attempt to delete IP Filter ,but the host IP address is not

exist Recommended Action Make sure the host IP address is exist.


3.4.8 Secure HTTP

This section contains Secure HTTP module messages. Error Message Incorrect input! Invaild HTTP Secure Port Number. HTTP Secure

Port Set Failed! Explanation User input invalid port number for HTTP Secure Port. Recommended Action User can not configure specific protocol port number which is

used by other protocol for HTTP Secure Port. <ex. telnet: 23, SSH: 22, HTTP: 80>

Error Message Incorrect input! Use 'ip http secure-protocol [TLS1] [SSL3]'. Explanation User input incomplete command. Recommended Action Use 'ip http secure-protocol [TLS1] [SSL3]'.

Error Message Protocol <protoclType> could not be set. Explanation User input invalid value for setting secure-protocol type. Recommended Action Use [TLS1] or [SSL3] to configure.

Error Message Incorrect input! Use 'ip http secure-port <1-65535>'. Explanation User input incomplete command. Recommended Action Use 'ip http secure-port <1-65535>'.


3.4.9 Secure Shell

This section contains Secure Shell module messages. Error Message Incorrect input! Use 'ip ssh protocol [1] [2]'. Explanation User input incomplete command . Recommended Action Use 'ip ssh protocol [1] [2]'.

Error Message Incorrect input! Valid values for ssh protocols are 1 and 2. Explanation User input invalid version value for ssh protocol. Recommended Action Use version 1 or 2 for ssh protocol .

Error Message Incorrect input! Use 'ip ssh protocol [1] [2]'. Explanation User input incomplete command . Recommended Action Use 'ip ssh protocol [1] [2]'.

Error Message Sorry, maximum number of SSH connections reached! Explanation Maximum number of SSH connections reached. Recommended Action Disconnect other SSH connections or use command 'ip ssh

maxsessions <0-5>' to change the maximum of SSH connections. The maximum number of SSH connection is 5.

Error Message Incorrect input! Use 'ip ssh maxsessions <0-5>'. Explanation User input incomplete command . Recommended Action Use 'ip ssh maxsessions <0-5>'.

Error Message Incorrect input! Use 'ip ssh timeout <1-160>'. Explanation User input incomplete command . Recommended Action Use 'ip ssh timeout <1-160>'.


3.4.10 Denial-of-Service

This section contains Denial-of-Service module messages.

Error Message Incorrect Input! Use 'dos-control icmpv6 <maxIcmpSize>'. Explanation User input incomplete command. Recommended Action Use 'dos-control icmpv6 <maxIcmpSize>'.


3.5 QoS

3.5.1 DiffServ

This section contains DiffServ module messages.

Error Message Could not delete the Diffserv class. Explanation User try to delete a DiffSev Class-map, but the class is still being

used in a Policy-map configuration. Recommended Action User should delete the DiffServ policy that has the Class-map

setting, and then delete the Class-map configuration.

Error Message Could not delete the DiffServ policy. Explanation User try to delete a DiffServ Policy-map, but the policy is still

being applied on interface(s). Recommended Action User should remove the policy from the interface(s), and then

delete the Policy-map configuration.

Error Message No more Policies can be created. Explanation User attempt to create a policy-map when table is full. Recommended Action Maximum 64 policy-map name can be created.

Error Message This Diffserv class already exists. Explanation User input an exist class name. Recommended Action Use other name for class name.

Error Message A Diffserv class with new name already exists. Explanation User try to modify the name of Class-map, but the new name

has existed in the system. Recommended Action Use a name that doesn’t use in the system.

Error Message Class Name does not exist. Explanation User try to use a DiffServ class, but the class name doesn’t exist.Recommended Action Use the correct DiffServ class name for this function.

Error Message This Diffserv policy does not exist. Explanation User try to use a DiffServ policy, but the policy name doesn’t

exist. Recommended Action Use the correct DiffServ policy name for this function.


Error Message A Diffserv policy with this name already exists. Explanation User try to modify the name of Policy-map, but the new name

has existed in the system. Recommended Action Use a name that doesn’t use in the system.

Error Message Class name must be alpha-numeric characters. Explanation User configure a non alpha-numeric characters for DiffServ

Class-map name. Recommended Action Use alpha-numeric characters to configure Class-map name.

Error Message Incorrect input! Use 'class-map rename <classname>

<newclassname>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘class-map rename <classname>

<newclassname>'

Error Message Incorrect input! Use 'match cos <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match cos <0-7>'

Error Message Incorrect input! Use 'match secondary-cos <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match secondary-cos <0-7>'

Error Message Incorrect input! Use 'match dstip <ipaddr> <ipmask>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match dstip <ipaddr> <ipmask>'

Error Message Incorrect input! Use 'match dstl4port { <portkey> | <0-65535> }' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match dstl4port { <portkey> |

<0-65535> }'

Error Message Incorrect input! Use 'match destination-address mac <macaddr>

<macmask>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match destination-address mac

<macaddr> <macmask>'


Error Message Incorrect input! Use 'match ethertype {<keyword> |

<0x0600-0xffff>}' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match ethertype {<keyword> |

<0x0600-0xffff>}'

Error Message Incorrect input! Use 'match ip dscp <dscpval>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match ip dscp <dscpval>'

Error Message Incorrect input! Use 'match ip precedence <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match ip precedence <0-7>'

Error Message Incorrect input! Use 'match ip tos <tosbits> <tosmask>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match ip tos <tosbits> <tosmask>'

Error Message Incorrect input! Use 'match protocol { <protocol-name> |

<0-255> }' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match protocol { <protocol-name> |

<0-255> }'

Error Message Incorrect input! Use 'match class-map <refclassname>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match class-map <refclassname>'

Error Message Incorrect input! Use 'no match class-map <refclassname>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no match class-map <refclassname>'

Error Message Incorrect input! Use 'match srcip <ipaddr> <ipmask>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match srcip <ipaddr> <ipmask>'


Error Message Incorrect input! Use 'match srcl4port { <portkey> | <0-65535> }' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match srcl4port { <portkey> |

<0-65535> }'

Error Message Incorrect input! Use 'match source-address mac <address>

<macmask>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match source-address mac <address>

<macmask>'

Error Message Incorrect input! Use 'match vlan <0-4095>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match vlan <0-4095>'

Error Message Incorrect input! Use 'match secondary-vlan <0-4095>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘match secondary-vlan <0-4095>'

Error Message Could not configure the DSCP mark value. Incompatible with 'mark ip-precedence'.

Explanation User try to add an IP DSCP attribute in the policy table, but there is a ‘mark ip-precedence’ setting in the same policy instance.

Recommended Action The ‘mark ip-dscp’ setting can not work with ‘mark ip- precedence’ setting in the same policy instance.

Error Message Could not configure the DSCP mark value. Incompatible with

'police'. Explanation User try to add an IP DSCP attribute in the policy table, but there

is a ‘police-simple’ setting in the same policy instance. Recommended Action The ‘mark ip-dscp’ setting can not work with ‘police-simple’

setting in the same policy instance.

Error Message Could not configure the cos mark value. Explanation User try to add a CoS attribute in the policy table, but there is a

conflict setting in the same policy instance. Recommended Action The ‘mark cos’ setting can not work with ‘police-simple’ or ‘mark

ip-dscp’ or ‘mark ip-precedence’ setting in the same policy instance.


Error Message Could not configure the precedence mark value. Incompatible with 'mark ip-dscp'.

Explanation User try to add an IP Precedence attribute in the policy table, but there is a ‘mark ip-dscp’ setting in the same policy instance.

Recommended Action The ‘mark ip-precedence’ setting can not work with ‘mark ip-dscp’ setting in the same policy instance.

Error Message Could not configure the precedence mark value. Incompatible

with 'police'. Explanation User try to add an IP Precedence attribute in the policy table, but

there is a ‘police-simple’ setting in the same policy instance. Recommended Action The ‘mark ip-precedence’ setting can not work with

‘police-simple’ setting in the same policy instance.

Error Message Could not configure the simple traffic policy. Incompatible with

'mark ip-dscp'. Explanation User try to add a ‘police-simple’ setting in the policy table, but

there is a ‘mark ip-dscp’ setting in the same policy instance. Recommended Action The ‘police-simple’ setting can not work with ‘mark ip-dscp’

setting in the same policy instance.


'mark ip-precedence'. Explanation User try to add a ‘police-simple’ setting in the policy table, but

there is a ‘mark ip-precedence’ setting in the same policy instance.

Recommended Action The ‘police-simple’ setting can not work with ‘mark ip-precedence’ setting in the same policy instance.


'mark cos'. Explanation User try to add a ‘police-simple’ setting in the policy table, but

there is a ‘mark cos’ setting in the same policy instance. Recommended Action The ‘police-simple’ setting can not work with ‘mark cos’ setting in

the same policy instance.

Error Message Class name must be of 31 characters or less. Explanation User try to use a DiffServ Class name that exceed 31 characters.Recommended Action The Class name must be of 31 characters or less.


Error Message Incorrect input! <tosbits> must be two digit hex value in the

range of 00 and ff. Explanation User configures a ToS custom value, but the ToS custom value

is out of range. Recommended Action ToS custom value is a two-digit hexadecimal number in the

range of 00 to ff.

Error Message Incorrect input! <tosmask> must be two digit hex value in the

range of 00 and ff. Explanation User configures a ToS mask value, but the ToS mask value is

out of range. Recommended Action ToS mask value is a two-digit hexadecimal number in the range

of 00 to ff.

Error Message Incorrect input! Ethertype custom value must be from 0x0600 to

0xffff. Explanation User configures a Ethertype custom value, but the Ethertype

custom value is out of range. Recommended Action Ethertype custom value is a four-digit hexadecimal number in the

range of 0x0600 to 0xffff.

Error Message Invalid Ethertype keyword or value. Explanation User configures a Ethertype parameter, but the Ethertype value

is out of range. Recommended Action Enter one of the following keywords to specify an Ethertype

(appletalk, arp, ibmsna, ipv4, ipv6, ipx, mplsmcast, mplsucast, netbios, novell, pppoe, rarp), or a four-digit hexadecimal number in the range of 0x0600 to 0xffff.

Error Message Invalid keyword. Currently supported values are domain, echo,

ftp, ftpdata, http, smtp, snmp, telnet, tftp, www. Explanation User configures a Layer-4 protocol parameter, but the protocol

keyword is incorrect. Recommended Action System currently supported domain, echo, ftp, ftpdata, http,

smtp, snmp, telnet, tftp and www keywords..

Error Message Incorrect input! <macmask> must be of type <aa:bb:cc:dd:ee:ff>.Explanation User configures a MAC address mask parameter, but the MAC

address mask value is out of range or the format is incorrect. Recommended Action Use the correct MAC address mask setting for this function.


Error Message Invalid MAC address. Explanation User configures a MAC address parameter, but the MAC

address value is out of range or the format is incorrect. Recommended Action Use the correct MAC address setting for this function.

Error Message Invalid keyword. Currently supported values are icmp, igmp, ip,

tcp, udp. Explanation User configures a Ethernet protocol parameter, but the protocol

keyword is incorrect. Recommended Action System currently supported icmp, igmp, ip, tcp and udp types.

Error Message No more attributes can be specified. Explanation User try to add a new policy attribute, but the policy attribute

table has reached the maximum. Recommended Action Use command ‘show diffserv’ to display the DiffServ table.

Because the policy attribute can’t be removed. User should delete a DiffServ policy setting, and create a new Policy-map. Then add the new attribute for the policy.

Error Message No more classes can be created. Explanation User try to create a new DiffServ Class-map setting, but the

number of class setting has reached the maximum. Recommended Action Use command ‘show diffserv’ to display the DiffServ table. User

should delete a DiffServ class setting that doesn’t use, and then create the new one.

Error Message No more criteria can be added. Explanation User try to create a new DiffServ Class match rule, but the class

rule table has reached the maximum. Recommended Action Use command ‘show diffserv’ to display the DiffServ table.

Because the class rule can’t be removed. User should delete a DiffServ class setting, and create a new Class-map. Then add the new rule for the DiffServ class.

Error Message Policy name must be alpha-numeric characters. Explanation User configures a non alpha-numeric characters for DiffServ

Policy-map name. Recommended Action Use alpha-numeric characters to configure Policy-map name.

Error Message Policy name must be of 31 characters or less. Explanation User try to use a DiffServ policy name that exceed 31

characters. Recommended Action policy name must be of 31 characters or less.


Error Message Reference class name must be of 31 characters or less. Explanation User try to use a DiffServ class name that exceed 31 characters.Recommended Action The class name must be of 31 characters or less.

Error Message This reference class does not exist. Explanation User try to configure a reference rule in DiffServ Class-map, but

the reference class doesn’t exist. Recommended Action Use the correct Class-map name for this function.

Error Message Reference class name must be alpha-numeric characters. Explanation User configures a non alpha-numeric characters for DiffServ

Class-map name. Recommended Action Use alpha-numeric characters to configure Class-map name.

Error Message Incorrect input! Self-referencing of class name not allowed Explanation User try to configure a reference rule in DiffServ Class-map, but

the reference class is itself. Recommended Action User should use another DiffServ class for this function.

Error Message Error! Cannot specify both mirror and redirect in same policy

instance. Explanation User try to add ‘redirect’ and ‘mirror’ setting in the same policy

instance. Recommended Action The ‘mirror’ setting can not work with ‘redirect’ setting in the

same policy instance.

Error Message Could not configure drop. Explanation User try to add a ‘drop’ setting in the policy table, but there is a

conflict setting in the same policy instance. Recommended Action The ‘drop’ setting can not work with other settings in the same

policy instance.

Error Message This Diffserv class does not exist. Explanation User try to display or configure a Class-map, but the Class-map

doesn’t exist. Recommended Action Use the correct Class-map name for this function.


Error Message This Diffserv policy does not exist. Explanation User try to display or configure a Policy-map, but the Policy-map

doesn’t exist. Recommended Action Use the correct Policy-map name for this function.

Error Message Invalid DSCP value. Explanation User configures a DSCP parameter, but the DSCP value is out

of range. Recommended Action Use should enter a DSCP value(0-63) or a DSCP keyword

(10(af11), 12(af12), 14(af13), 18(af21), 20(af22), 22(af23), 26(af31), 28(af32), 30(af33), 34(af41), 36(af42), 38(af43), 0(be), 0(cs0), 8(cs1), 16(cs2), 24(cs3), 32(cs4), 40(cs5), 48(cs6), 56(cs7), 46(ef) .

Error Message Incorrect input! Use 'assign-queue <queueid>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘assign-queue <queueid>'

Error Message Incorrect input! Use 'mark { cos <0-7> | ip-dscp <dscpval> | ip-precedence <0-7> }'

Explanation Incomplete command for this function. Recommended Action Use complete command ‘mark { cos <0-7> | ip-dscp <dscpval> |

ip-precedence <0-7> }'

Error Message Incorrect input! Use 'mark ip-precedence <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘mark ip-precedence <0-7>'

Error Message Incorrect input! Use 'mark cos <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘mark cos <0-7>'


Error Message Incorrect input! Use 'police-simple {<1-4294967295> <1-128>

conform-action {drop | set-cos-transmit <0-7> | set-dscp-transmit <0-63> | set-prec-transmit <0-7> | transmit} violate-action {drop | set-dscp-transmit <0-63> | set-prec-transmit <0-7> | transmit}}'

Explanation Incomplete command for this function. Recommended Action Use complete command ‘police-simple {<1-4294967295>

<1-128> conform-action {drop | set-cos-transmit <0-7> | set-dscp-transmit <0-63> | set-prec-transmit <0-7> | transmit} violate-action {drop | set-dscp-transmit <0-63> | set-prec-transmit <0-7> | transmit}}'

Error Message Incorrect input! Use 'conform-color <class-map-name> [exceed-color <class-map-name>]'

Explanation Incomplete command for this function. Recommended Action Use complete command 'conform-color <class-map-name>

[exceed-color <class-map-name>]'

Error Message Incorrect input! Use 'conform-color <class-map-name>' in

conjunction with simple policing. Explanation Incomplete command for this function. Recommended Action Use complete command 'conform-color <class-map-name>' in

conjunction with simple policing.

Error Message Incorrect input! Use 'mirror <slot/port>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘mirror <slot/port>'

Error Message Incorrect input! Use 'policy-map rename <policyname>

<newpolicyname>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘policy-map rename <policyname>

<newpolicyname>'

Error Message Incorrect input! Use 'redirect <slot/port>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘redirect <slot/port>'


Error Message Incorrect input! Use 'service-policy in <policy-map-name>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘service-policy in <policy-map-name>'

Error Message Incorrect input! Use 'no service-policy in <policy-map-name>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no service-policy in

<policy-map-name>'

Error Message Incorrect input! Use 'no policy-map <policyname>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no policy-map <policyname>'

Error Message Incorrect input! Use 'show diffserv service brief [in]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show diffserv service brief [in]'

Error Message Incorrect input! Use 'show diffserv' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show diffserv'

Error Message Incorrect input! Use 'show class-map [<classname>]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show class-map [<classname>]'

Error Message Incorrect input! Use 'show policy-map [<policyname>]' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show policy-map [<policyname>]'

Error Message Incorrect input! Use 'show diffserv service {<slot/port>|brief} {in}' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show diffserv service {<slot/port>|brief}

{in}'

Error Message Incorrect input! Use 'show diffserv service {<slot/port>|brief}' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show diffserv service {<slot/port>|brief}'


Error Message Incorrect input! Use 'show policy-map interface <slot/port> {in}' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show policy-map interface <slot/port>

{in}'

Error Message Incorrect input! Use 'show service-policy <in>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show service-policy <in>'

Error Message An invalid interface has been used for this function. Explanation Wrong interface identifier is used for this function. Recommended Action Use the correct interface identifier for this function.

Error Message No interfaces to display in the specified direction. Explanation Use command ‘show service-policy in’ to display the DiffServ

status of each interface, but there is no interface has applied the DiffServ policy.

Recommended Action User should apply the DiffServ policy to interface first, then can use this command to display DiffServ status of interfaces.


3.5.2 COS Messages


Error Message Incorrect input! Use 'show queue cos-queue <slot/port>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show queue cos-queue <slot/port>'

Error Message Incorrect input! Use 'show queue trust <slot/port>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show queue trust <slot/port>'

Error Message Incorrect input! Use 'show queue cos-map <slot/port>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘show queue cos-map <slot/port>'

Error Message Incorrect input! Use 'switchport priority <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘switchport priority <0-7>'

Error Message Incorrect input! Use 'switchport priority all <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘switchport priority all <0-7>'

Error Message Incorrect input! Use 'queue cos-map <0-7> <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-map <0-7> <0-7>'

Error Message Incorrect input! Use 'queue cos-map all <0-7> <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-map all <0-7> <0-7>'

Error Message Incorrect input! Use 'no queue cos-map all' Explanation Incomplete command for this function. Recommended Action Use complete command ‘no queue cos-map all'


Error Message Incorrect input! Each bandwidth value must be from 0 to 100 in

increments of 5. Explanation Wrong bandwidth value for this function. Recommended Action The bandwidth value must be from 0 to 100 in increments of 5.

For example: 5, 10, 15…

Error Message Incorrect input! Use 'queue trust {dot1p | ip-dscp | untrusted}' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue trust {dot1p | ip-dscp |

untrusted}'

Error Message Incorrect input! Use 'queue cos-queue traffic-shape <bw>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-queue traffic-shape <bw>'.

<bw> is the shaping bandwidth percentage from 0 to 100 in increments of 5.

Error Message Incorrect input! Use 'queue cos-queue traffic-shape all <bw>'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-queue traffic-shape all

<bw>'. <bw> is the shaping bandwidth percentage from 0 to 100 in increments of 5.

Error Message Incorrect input! Use 'queue cos-queue strict <queue-id>’. Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-queue strict <queue-id>.

Error Message Incorrect input! Use 'no queue cos-queue strict <queue-id> Explanation Incomplete command for this function. Recommended Action Use complete command ‘no queue cos-queue strict <queue-id>’

Error Message Incorrect input! Use 'queue cos-queue strict all <queue-id>’ Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-queue strict all <queue-id>’

Error Message Incorrect input! Use 'no queue cos-queue strict all <queue-id>’ Explanation Incomplete command for this function. Recommended Action Use complete command ‘no queue cos-queue strict all

<queue-id>’


Error Message Incorrect input! Use 'queue cos-queue min-bandwidth

<bw-0>..<bw-7>. Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-queue min-bandwidth

<bw-0>..<bw-7>.

Error Message Incorrect input! Total minimum bandwidth must not exceed 100

percent. Explanation Total bandwidth value has exceeded 100%. Recommended Action Sum of bandwidth value must below 100%.

Error Message Incorrect input! Use 'queue cos-queue min-bandwidth all

<bw-0>..<bw-7>. Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-queue min-bandwidth all

<bw-0>..<bw-7>.

Error Message Incorrect input! Use 'queue ip-dscp-mapping <ipdscp>

<trafficclass>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue ip-dscp-mapping <ipdscp>

<trafficclass>'

Error Message Invalid IP DSCP Value. Explanation Wrong DSCP value for this function. Recommended Action Enter the IP DSCP value in the range of 0 to 63 or an IP DSCP

keyword (af11, af12, af13, af21, af22, af23, af31, af32, af33, af41, af42, af43, be, cs0, cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef).

Error Message Incorrect input! Use 'queue trust {dot1p | ip-dscp | untrusted} all' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue trust {dot1p | ip-dscp |

untrusted} all'

Error Message Incorrect input! Use 'queue trust {dot1p | ip-dscp | untrusted}' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue trust {dot1p | ip-dscp |

untrusted}'


Error Message Incorrect input! Use 'no queue trust all'. Explanation Incomplete command for this function. Recommended Action Use complete command ‘no queue trust all'.

Error Message Incorrect input! Use 'queue cos-map <0-7> <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-map <0-7> <0-7>'

Error Message Incorrect input! Use 'queue cos-map all <0-7> <0-7>' Explanation Incomplete command for this function. Recommended Action Use complete command ‘queue cos-map all <0-7> <0-7>'


3.6 Stacking

This section contains the Stacking messages.

Error Message Incorrect input! Use 'show switch [unit]'. Explanation User attempt to show a non-exist switch CB name. Recommended Action Make sure the switch name is exist .

Error Message Switch # does not exist! Explanation User attempt to show or reload a non-exist switch unit number. Recommended Action Make sure the switch unit is exist .

Error Message Reloading switch #. Explanation User specify to reload a switch unit. Recommended Action User specify to reload a switch unit.

Error Message Reloading all switches. Explanation User reload the management switch of stacking. Recommended Action Reload Mgmt switch will reload all switches of the stack.

Error Message Incorrect input! Use 'reload [slot <unit>]'. Explanation User input incomplete command . Recommended Action Use 'reload [slot <unit>]'.

Error Message ERROR: Invalid switch ID! Explanation User try to configure a unit of stacking platform, but the unit

number is out of range. Recommended Action The range of unit number is from 1 to 8.

Error Message Switch <Id> does not exist! Explanation User try to reload a unit, but the unit number doesn’t exist. Recommended Action Use the correct unit number for this function.

Error Message ERROR: The first switch designated must be the current

management switch! Explanation User attempt to move stack management functionality to a unit,

but the first unit number is not the current management unit. Recommended Action Use the correct management unit number for this function.


Error Message Incorrect input! Use 'switch <unit> priority <value>'

or Use 'switch <unit> provision' or Use 'switch movemanagement <fromunit> <tounit>'.

Explanation User input incomplete command . Recommended Action Use 'switch <unit> priority <value>'

or Use 'switch <unit> provision' or Use 'switch movemanagement <fromunit> <tounit>'.

Error Message User Input Error: Switch priority must be in the range of 0 to 15! Explanation User input invalid value for switch priority. Recommended Action Use value in the range of 0 to 15.

Error Message Incorrect input! Use 'switch <unit> priority <value>'. Explanation User input incomplete command . Recommended Action Use 'switch <unit> priority <value>'.

Error Message Incorrect input! Use 'switch movemanagement <fromunit> <tounit>'.

Explanation User input incomplete command . Recommended Action Use 'switch movemanagement <fromunit> <tounit>'.

Error Message Incorrect input! Use 'no switch <unit> {provision | priority}'. Explanation User input incomplete command . Recommended Action Use 'no switch <unit> {provision | priority}'.

Error Message The new priority will be applied to the master election process if

the re-election is required. Explanation User modify the stacking priority of a unit, the priority is effective

after re-election process. Recommended Action Remove the stacking cable and reconnect it to have switch

re-election.

Error Message Unit <unit Id> does not exist. Explanation User try to move stack management functionality to a unit, but

the unit number doesn’t exist. Recommended Action Use the correct unit number for this function.


Error Message Source and Target Switch ID should not be the same. Explanation User try to move stack management functionality to a unit, but

the source and target unit number is the same. Recommended Action Use the correct source and target unit number for this function.

Error Message Incorrect input! Use 'archive copy-sw [destination-system

<unit>]'. Explanation User input incomplete command . Recommended Action Use 'archive copy-sw [destination-system <unit>]'.

Error Message Incorrect input! Use 'archive download-sw <url>' Explanation User input incomplete command . Recommended Action Use 'archive download-sw <url>'

Error Message Invalid url specified! Use xmodem or

tftp://<ipaddress>/<filepath>/<fileName>. Explanation User input incorrect URL format. Recommended Action Use the correct URL format for this function.

Error Message ERROR: Filename must be 31 alphanumeric characters or less! Explanation User input the file name length is over 31 characters. Recommended Action The file name length should less than 31 characters.

Error Message ERROR: Filepath must be 95 alphanumeric characters or less! Explanation User input the file path length is over 95 characters. Recommended Action The file path length should less than 95 characters.

Error Message Cannot Use Xmodem Transmit Function in TELNET. Explanation User try to download software by Xmodem protocol, but the

management connection is from Telnet method not from Console (serial) port.

Recommended Action User should use the Console port to manage switch, and download software by Xmodem protocol.


3.7 End-Host-Mode

This section contains the pin-group messages.

Error Message Incorrect input! Pin Group %s has been used!! Explanation The pin-group name is already used. Recommended Action Use new name for pin-group.

Error Message Incorrect input! Pin Group <pinGroupName> does not exist!! Explanation The specified pin-group is not exist. Recommended Action Use command ‘show pin-group [<pinGroupName>]’ to find all

configured pin-group.


4 Web Error Messages

4.1 Management

4.1.1 Configuration

This section contains the Configuration In-Band Mgmt messages.

Error Message Error : Invalid IP Address ! Explanation User input an invalid or reserved IP address. Recommended Action Use the valid IP address for this function. IP address should be

in a.b.c.d format where range for a, b, c, and d is 1 - 255.

Error Message Error: Subnet mask must have contiguous ones. Explanation User input an IP subnet mask that does not have contiguous



Error Message Error: Value (<value>) is out of range for Managenent VLAN ID.

The valid range is 1 to 4094. Explanation The value of VLAN ID is out of range. Recommended Action The value of VLAN ID is 1 to 4094.

Error Message Error : This vlan does not exist. Explanation User configure the Management VLAN ID, but the VLAN ID

doesn’t exist in the system. Recommended Action Create the VLAN ID first and then set the Management VLAN ID

to this VLAN.

Error Message Error: Error: Failed to set port number. Explanation The value of WEB port number is out of range. Recommended Action The range of the WEB port number is 1 to 65535.


This section contains the Configuration Out-Band Mgmt messages.

Error Message Error : Invalid IP Address ! Explanation User input an invalid or reserved IP address. Recommended Action Use the valid IP address for this function. IP address should be


Error Message Warning: Changing protocol mode will reset IP configuration. Explanation User try to change the interface protocol mode, system will

pop-up a message to remind the current IP address will be cleared.

Recommended Action No recommended action, it just a warning message.

Error Message Error: IP Address requires an IP address in x.x.x.x form with

each octet(x) in the range 0-255. Explanation User input an invalid format IP address. Recommended Action Use the valid IP address for this function. IP address should be


Error Message Error: Subnet mask must have contiguous ones. Explanation User input an IP subnet mask that does not have contiguous



Error Message Error: Subnet Mask requires a subnet mask in x.x.x.x form. Explanation User input an invalid format IP Subnet mask. Recommended Action Use the valid IP Subnet mask for this function. Subnet mask

should be in a.b.c.d format where range for a, b, c, and d is 1 - 255.

Error Message Error : Invalid Gateway IP Address ! Explanation User input an invalid or reserved IP address. Recommended Action Use the valid IP address for this function. IP address should be



Error Message Error: Failed to set gateway. IP address and gateway do not lie

on the same subnet. Explanation User input a gateway IP address, but the gateway IP address

and OOB IP address doesn’t lie on the same subnet. Recommended Action The gateway IP address and OOB IP address should lie on the

same subnet.


This section contains the Configuration Telnet Session messages.

Error Message Error: Telnet Login Timeout format is invalid. Explanation User configure non-numeric characters for Telnet Login Timeout.Recommended Action Use numeric characters to configure Telnet Login Timeout.

Error Message Error: Value (<value>) is out of range for Telnet Login Timeout.

The value of range is 1 to 160. Explanation The value of Telnet Login Timeout is out of range. Recommended Action The range for Telnet Login Timeout is 1 to 160.

Error Message Error: Password Threshold formate is invalid. Explanation User configure non-numeric characters for Password Threshold. Recommended Action Use numeric characters to configure Password Threshold.

Error Message Error: Value (<value>) is out of range for Password Threshold.

The value of range is 1 to 120. Explanation The value of Password Threshold is out of range. Recommended Action The range for Password Threshold is 1 to 120.


This section contains the Configuration Telnet Client Config messages.

Error Message Error: Value (<value>) is out of range for Session Timeout. The

valid range is 1 to 160. Explanation The value of the Session Timeout is out of range or

non-unnumber characters. Recommended Action Use numeric characters and the range for Session Timeout is 1

to 160.

Error Message Error: Value (<value>) is out of range for Terminal Length. The

valid range is 10 to 100. Explanation The value of the Terminal Length is out of range or non-numeric

characters. Recommended Action Use numeric characters and the range for Terminal Length is 10

to 100.


This section contains the Configuration SSH Client Config messages.

Error Message Error: Value (<value>) is out of range for Session Timeout. The

valid range is 1 to 160. Explanation The value of the Session Timeout is out of range or

non-unnumber characters. Recommended Action Use numeric characters and the range for Session Timeout is 1

to 160.


This section contains the Configuration Serial Port messages.

Error Message Error: Serial Port Timeout (minutes) formate is invaild. Explanation User configure non-numeric characters for Serial Port Login

Timeout. Recommended Action Use numeric characters to configure Serial Port Login Timeout.

Error Message Error: Value (<value>) is out of range for Serial Port Login

Timeout (minuter). The value range is 0 to 160. Explanation The value of Serial Port Login Timeout is out of range.. Recommended Action The range for Serial Port Login Timeout is 0 to 160.

Error Message Error: Password Threshold formate is invalid. Explanation User configure non-numeric characters for Password Threshold. Recommended Action Use numeric characters to configure Password Threshold.

Error Message Error: Value (<value>) is out of range for Password Threshold.

The value of range is 0 to 120. Explanation The value of Serial Port Login Timeout is out of range. Recommended Action The range for Serial Port Login Timeout is 0 to 120.

Error Message Error: Silent Time (Sec) format is invalid. Explanation User configure non-numeric characters for Silent Time. Recommended Action Use numeric characters to configure Silent Time.

Error Message Error: Value (<value>) is out of range of range for Silent Time

(Sec). The vaild is 0 to 65535. Explanation The value of Silent Time is out of range. Recommended Action The range for Silent Time is 0 to 65535.

Error Message Error: value (<value>) is out of range Terminal Length. The valid

range is 10 to 100. Explanation The value of Terminal Length is out of range or non-numeric

characters. Recommended Action Use numeric characters and the range for Terminal Length is 10

to 100.


This section contains the Configuration HTTP Config messages.

Error Message Error! HTTP Session Soft Timeout format is invalid. Explanation User configure non-numeric characters for HTTP Session Soft

Timeout. Recommended Action Use numeric characters to configure HTTP Session Soft

Timeout.

Error Message Error! value (<value>) is out of range for http Soft Timeout. The

valid. The valid range is 0 to 60. Explanation The value of HTTP Session Soft Timeout is out of range. Recommended Action The range for HTTP Session Soft Timeout is 0 to 60.

Error Message Error! HTTP Session Hard Timeout format is invalid. Explanation User configure non-numeric characters for HTTP Session Hard

Timeout. Recommended Action Use numeric characters to configure HTTP Session Hard

Timeout.

Error Message Error! value (<value>) is out of range for http Hard Timeout. The

valid range is 0 to 168. Explanation The value of HTTP Session Hard Timeout is out of range. Recommended Action The range for HTTP Session Hard Timeout is 0 to 168.

Error Message Error! Maximum Number of HTTP Session format is invalid. Explanation User configure non-numeric characters for Maximum Number of

HTTP Session. Recommended Action Use numeric characters to configure Maximum Number of HTTP

Session.

Error Message Error! value (<value>) is out of range for Maximum Number of

HTTP Sessions. The valid range is 0 to 16. Explanation The value of Maximum Number is out of range. Recommended Action The range for Maximum Number is 0 to 16.


This section contains the Configuration DDNS Config messages.

Error Message Error: Host Name can’t be empty. Explanation The Host Name is empty when adding a new DDNS setting. Recommended Action The Host Name can’t be empty.

Error Message Error: User Name can’t be empty. Explanation The User Name is empty when adding a new DDNS setting. Recommended Action The User Name can’t be empty.

Error Message Error: Password can’t be empty. Explanation The Password of User Name is empty when adding a new

DDNS setting. Recommended Action The Password of User Name can’t be empty.

Error Message Error: Invalid Input : IP address. Explanation User input an invalid or reserved IP address. Recommended Action Use the valid IP address for this function. IP address should be



4.1.2 System Utilities

This section contains the Traceroute messages.

Error Message Error: Invalid Input : IP address. Explanation User input a invalid IP address for Traceroute address. Recommended Action Use a valid IP address for Traceroute address.

Error Message Error: Probes Per Hop format is invalid.

Error: Form Submission Failed! Explanation User input a non-numeric value for Probes Per Hop. Recommended Action Use numeric value for Probes Per Hop.

Error Message Error! value (<value>) is out of range for Probes Per Hop. The

valid range is 1 to 10. Error: Form Submission Failed!.

Explanation The value of the Probes Per Hop is out of range. Recommended Action The value of field should be in the range of 1 to 10.

Error Message Error: MaxTTL format is invalid.

Error: Form Submission Failed! Explanation User input non-numeric value for MaxTTL. Recommended Action Use numeric value for MaxTTL.

Error Message Error! value (<value>) is out of range for MaxTTL. The valid

range is 1 to 255. Error: Form Submission Failed!.

Explanation The value of the MaxTTL is out of range. Recommended Action The value of field should be in the range of 1 to 255.

Error Message Error: InitTTL format is invalid.

Error: Form Submission Failed! Explanation User input non-numeric value for InitTTL. Recommended Action User numeric value for InitTTL.

Error Message Error! value (<value>) is out of range for InitTTL. The valid range

is 1 to 255. Error: Form Submission Failed!.

Explanation The value of the InitTTL is out of range. Recommended Action The value of field should be in the range of 1 to 255.


Error Message Error: Interval format is invalid.

Error: Form Submission Failed! Explanation User input non-numeric value for Interval. Recommended Action Use numeric value for the Interval.

Error Message Error! value (<value>) is out of range for Interval. The valid range

is 1 to 255. Error: Form Submission Failed!.

Explanation The value of the Interval is out of range. Recommended Action The value of field should be in the range of 1 to 255.


This section contains the Ping messages.

Error Message Error : Invalid IP Address ! Explanation User input a invalid IP address for the Ping address. Recommended Action Use the valid IP address for the Ping address.

Error Message Error: Invalid Host Name Explanation User input non-alphanumeric characters for Host Name. Recommended Action Use alphanumeric characters for Host Name.

Error Message Error: IPv6 Address format is invalid. Explanation The input IPv6 address format is invalid. Recommended Action Use a valid IPv6 address for this field.

Error Message Error: Invalid Input : Link Local Address. Explanation The value of Link Local Address is invalid. Recommended Action Use a valid Link Local Address.

Error Message Error: Datagram Size format is invalid. Explanation User input non-numeric value for the Datagram Size. Recommended Action Use numeric value for the Datagram Size.

Error Message Error: Value (<value>) is out of range for Datagram Size. The

valid range is 48 to 2048. Explanation The value of Datagram Size format is out of range. Recommended Action The value of field should be in the range of 48 to 2048.


4.1.3 File Management

This section contains the Download To Switch messages.

Error Message Error: Invalid TFTP Server IP address. Explanation The value of the IP address of TFTP Server is a invalid IP

address Recommended Action Use a valid IP address for TFTP Server address.

Error Message Error: Failed to set TFTP File Name <filename>. Explanation User input the wildcard characters for File Name. For example

the asterisk sign(*) or question mark(?). Recommended Action Use the correct file name for this function.

Error Message [<filename>] Target file extension other than '.scr' is not allowed. Explanation User try to download a script file to the switch, but the target file

extersion is not ‘.scr’. Recommended Action Use ‘.scr’ for the target script file extension.

Error Message Error: Destination File name not entered!

Error: Failed to set FTP/TFTP File Path. Path name length limit is 96 characters including the tailing slash.

Explanation The value of FTP/TFTP File Path over 96 characters. Recommended Action The value of field should be correct path and less than 96

characters.

Error Message Error: Destination File name not entered! Explanation The value of the Target Name is not entered.. Recommended Action Enter the Target Name to be stored in the switch.

Error Message Error: Cannot find partion table entry! Explanation Can not find any entry to store new file on the flash system. Recommended Action Two runtime codes are supported in the flash system. Please

delete one of the runtime codes before downloading the new one.


This section contains the Upload To Switch messages.

Error Message Error: Invalid TFTP Server IP address. Explanation The value of the IP address of TFTP Server is a invalid IP

address Recommended Action Use a valid IP address for TFTP Server address.

This section contains the Remove File messages.

Error Message Error: Fail to remove runtime file! Explanation Fail to remove the current used/booted runtime file. Recommended Action Change the booting file to another runtime file. Then you could

allow to delete this runtime file.


This section contains the Copy File messages.

Error Message Error: File name not entered Explanation User does not input the file name for Copy File function. Recommended Action Use should input a file name with alphanumeric characters for

this function. The maximum length of the file name is 30 characters.

Error Message Error: Failed to set File Name. Explanation User input the non-alphanumeric characters for this function. Recommended Action Use should input a file name with alphanumeric characters for

this function. The maximum length of the file name is 30 characters.


4.1.4 User Manangement

This section contains the User Accounts messages.

Error Message Error : Could't change admin name. Explanation The admin name can not be changed. Recommended Action The “admin” name is a default name in the system and it can not

be changed.

Error Message Error : Could't change guest name. Explanation The value of guest name can not be changed. Recommended Action The “guest” name is a default name in the system and it can not

be changed.

Error Message Error : The user name <username> has been used! Explanation The value of user name has been used. Recommended Action Use other user name for new account.

Error Message Error: Failed to set User Name. You entered <username>. Explanation The value of username includes special characters. Recommended Action Valid characters include all the alphanumeric characters as well

as the dash ('-') and underscore ('_') characters.

Error Message Error: Failed to set User Name. Invalid name entered. Explanation User name is not entered. Recommended Action Enter the user name before submitting the request.

Error Message Error: Failed to set Password. Password and Confirm Password

fields do not match. Explanation The value of Password field is not the same as the Confirm

Password. Recommended Action Make sure the value on those two fields is identical.

Error Message Error: Failed to set Password. Since authentication is enabled,

password must be exactly 8 characters in length. Explanation The value of Password must be exactly 8 characters in length if

the authentication protocol is specified. Recommended Action Use exactly 8 characters for your password if the authentication

protocol is used.


Error Message Error:Error! Encryption Key must be 8 to 64 characters in length. Explanation The value of Encryption Key is not 8 to 64 characters in length. Recommended Action The value of Encryption Key must be 8 to 64 characters in

length.

Error Message Error: Authentication is required for this user since encryption is

enabled. Explanation The value of authentication protocol is not specified for this user

while encryption protocol is used. Recommended Action Specify the authentication protocol if the encryption protocol is

used.

Error Message Error: Failed to set User Name. You entered <username>.

Error: Failed to set Password. You entered . Error: Failed to set User Name and Password.

Explanation The value of username includes special characters. Recommended Action Use valid characters include all the alphanumeric characters as

well as the dash ('-') and underscore ('_') characters for user name.

Error Message Error: The user name <username> has been used in SNMP! Explanation This name has been used in SNMP user. Recommended Action Use other name to create a new user account.

Error Message Error: Failed to set Password. Password must be at least

<Password Minimum Length> characters in length. Explanation Password must be at least <Password Minimum Length>

characters in length. Recommended Action The length of Password should greater than Password Minimum

Length.

Error Message Error: Value (<value>) is out of range for Password Minimum

Length. The valid range is 1 to 64. Explanation The value of Password Minimum Length is out of range. Recommended Action Make sure the value is in the range of 1 to 64.

Error Message Error: Privilege Level format is invalid. Explanation The value of Privilege Level is non-numeric or blank. Recommended Action Input a number for Privilege Level.


Error Message Error: Value (<value>) is out of range for Privilege Level. The valid range is 0 to 15.

Explanation The value of Privilege Level is out of range. Recommended Action Make sure the value is in the range of 0 to 15.

Error Message Error: Could't change admin Privilege Level. Explanation The admin Privilege Level can not be changed. Recommended Action The default admin Privilege Level is 15, and it can not be

changed.


This section contains the Authencation List Config messages.

Error Message Error: Failed to set methods in the Authentication Login List. The

default Athentication Login List can not be changed. Explanation “defaultList” is the default authentication login list in the system

and the methods of “defaultList” can’t be changed. Recommended Action The methods of “defaultList” can’t be changed.

Error Message Error: Failed to create Authentication Login List.. Explanation The value of Authentication Login List is failed to create with

empty list name. Recommended Action Enter authentication list name to create a login list.


This section contains the User Login messages.

Error Message Error: setting Authentication Login List this user. The

Authentication Login List for the admin user can not be changed.Explanation “admin” account can not be changed to other authentication

login list. It has to be in the defaultList. Recommended Action Can not change the authentication login list for “admin” account.


4.1.5 Logging

This section contains the Hosts messages.

Error Message Error: Local Port format is invalid. Explanation The value of Local UDP Port is not numeric value or out of range

1 to 65535. Recommended Action Use numeric value for the local port and the value of local port

should be in the range of 1 to 65535.

Error Message Error: A valid IP address is required. Explanation The input IP address is invalid. Recommended Action Use valid IP address for this field.

Error Message Error: IP address is duplicated. Explanation The IP address of this host is already configured. Recommended Action Use other IP address for the new host.

Error Message Error: Port format is invalid. Explanation The value of port is not numeric value. Recommended Action Use numeric value for the port field. The default port is 514 and it

should be in the range of 1 to 65535.

Error Message Incorrect input! do not use the DNS name in the IP address

format. Explanation Input IP address in the DNS name is invalid. Recommended Action Use valid DNS name in this field.

Error Message Error: A valid IPv6 address is required. Explanation The input IPv6 address is invalid Recommended Action Use valid IPv6 address in this field.


This section contains the Syslog messages.

Error Message Error: Local Port format is invalid.. Explanation The value of local port is not a numeric value. Recommended Action Use numeric value for the local UDP port. The default local port

is 514 and it should be in the range of 1 to 65535.


4.1.6 SNMP

This section contains the Community Config messages.

Error Message Error: Failed to set SNMP Community Name. Community name

not entered. Explanation The value of SNMP Community name is not entered. Recommended Action Enter SNMP community name to create new community.

Error Message Error: Failed to set SNMP Community Name. Invalid name

entered. Explanation User configure a non alpha-numeric characters for SNMP

Community Name. Recommended Action Use alpha-numeric characters to configure SNMP Community

Name.

Error Message Error: Client IP Mask requires a subnet mask in x.x.x.x form. Explanation The value of Client IP mask is not in x.x.x.x form. Recommended Action Use x.x.x.x form for Client IP mask.

Error Message Error: Failed to set the SNMP Community Name. This name is

already in use. Explanation The SNMP name is already configured in the system. Recommended Action Use other SNMP name for new community.

Error Message Error: Invalid Mask! Explanation Invalid mask is entered for the Client IP Mask. Recommended Action Use a valid mask for Client IP Mask.

Error Message Error: Invalid IP Address! Explanation The input Client IP address is a invalid IP address. Recommended Action Use a valid IP address for Client IP address.

Error Message Error: Invalid Prefix/Prefix Length! Explanation The input IPv6 Address is a invalid combination of Prefix/Prefix

Liegth. Recommended Action Use a valid combination of Prefix/Prefix Liegth.


This section contain the SNMP User Config message.

Error Message Error: Number of maximum SNMP user is reached! Explanation Maximum 6 SNMP user have been configured in the system. Recommended Action Reduce/Remove the unused SNMP user.

Error Message Error: The SNMP user name <name> has been configured! Explanation This name has been configured in the system. Recommended Action Change another different name.

Error Message Error: The user name <name> has been used! Explanation This name has been used in login. Recommended Action Change another different name.

Error Message Error: Failed to set Password. Since authentication is enabled,

password must be at least 8 characters in length. Explanation The length of the password must at least 8 characters. Recommended Action Input at least 8 chacraters in length.

Error Message Error! Encryption Key must be 8 to 64 characters in length. Explanation The length of the password must between 8 to 64 characters. Recommended Action Input 8 to 64 characters in length.


This section contain the SNMP EngineID Config message.

Error Message Error: IP Address is a mandatory field. Explanation The value of Ipv6 address is a mandatory field. Recommended Action Input a IPv6 address in this field.

Error Message Error: Invalid IPV6 Address Explanation The Input address is not a valid IPv6 address. Recommended Action Use a valid IPv6 address for IP Address field.

Error Message Error: This IP address is already configured. Explanation This IP address has been configured in the system. Recommended Action Use a different IP address for this engine ID.

Error Message Error: Engine ID is a mandatory field. Explanation The value of Engine ID is a mandatory field. Recommended Action Input a Engine ID in this field.

Error Message Error: Engine ID must contain Hexadecimal characters only. Explanation The value of Engine ID is hexadecimal characters only. Recommended Action You can only input 0-9 or a-f.


This section contains the Trap Receiver Config messages.

Error Message Error: Invalid IP Address! Explanation The input IP address for the new trap receiver is a invalid IP

address. Recommended Action Use a valid IP address for this field.

Error Message Error: Failed to set SNMP Community Name/SNMP User. Invalid

name entered. Explanation The input field is blank. Recommended Action Input a SNMP Community Name/SNMP User in this field.


Error Message Error: Snmptrap already exists! Explanation The combination of “SNMP Community Name/SNMP User“ and

“IP Address“ already configured. Recommended Action Input a different “SNMP Community Name/SNMP User“ and “IP

Address“.

Error Message Error: Invalid SNMP user. Explanation The user name is not exist. Recommended Action Create the user in SNMP User Config page.

Error Message Error: Inconsistent security level for SNMP user and SNMP trap. Explanation The security level is not match in SNMP User Config page. Recommended Action Select “NoAuthNoPriv” when Authentication Protocol and

Encryption Protocol are not setting. Select “authNoPriv” when only setting Authentication Protocol. Select “authPriv” when both Authentication Protocol and Encryption Protocol are setting.


This section contains the Inform Receiver Config messages.

Error Message Error : Inform Retries value <value> is out of range, the valid

value is from 0 to 100 Explanation The value of Inform Retries is out of range. Recommended Action Make sure the value is in the rage of 0 to 100.

Error Message Error : Inform Timeout value <value> is out of range, the valid

value is from 0 to 1000 Explanation The value of Inform Timeout is out of range. Recommended Action Make sure the value is in the range of 0 to 1000.

Error Message Error: Failed to set SNMP Community Name/SNMP User. Invalid

name entered. Explanation The input field is blank. Recommended Action Input a SNMP Community Name/SNMP User in this field.

Error Message Error: Invalid IP Address! Explanation The input IP address for the new inform receiver is a invalid IP

address. Recommended Action Use a valid IP address for this field.


Error Message Error: Snmpinform already exists! Explanation The combination of “SNMP Community Name/SNMP User“ and

“IP Address“ already configured. Recommended Action Input a different “SNMP Community Name/SNMP User“ and “IP

Address“.

Error Message Error: Invalid SNMP user. Explanation The user name is not exist. Recommended Action Create the user in SNMP User Config page.

Error Message Error: Inconsistent security level for SNMP user and SNMP

inform. Explanation The security level is not match in SNMP User Config page. Recommended Action Select “NoAuthNoPriv” when Authentication Protocol and

Encryption Protocol are not setting.


Select “authNoPriv” when only setting Authentication Protocol. Select “authPriv” when both Authentication Protocol and Encryption Protocol are setting.


4.1.7 SNTP

This section contains the Global Config messages.

Error Message Error: Value (<value>) is out of range for Port. The valid range is

1 to 65535. Explanation The value of Port is a non-numeric value or is out of range. Recommended Action Use numeric value for Port and make sure the value is in the

range of 1 to 65535.

Error Message Error: Value (<value>) is out of range for Unicast Poll Interval.

The range is 6 to 10. Explanation The value of Unicast Poll Interval is a non-numeric value or is out

of range. Recommended Action Use numeric value for Unicast Poll Interval and make sure the

value is in the range of 6 to 10.

Error Message Error: Value (<value>) is out of range for Broadcast Poll Interval.

The range is 6 to 10. Explanation The value of Broadcast Poll Interval is a non-numeric value or is

out of range. Recommended Action Use numeric value for Broadcast Poll Interval and make sure the


Error Message Error: Value (<value>) is out of range for Unicast Poll Timeout.

The range is 1 to 30. Explanation The value of Unicast Poll Timeout is a non-numeric value or is

out of range. Recommended Action Use numeric value for the Unicast Poll Timeout and make sure

the value is in the range of 1 to 30.

Error Message Error: Value (<value>) is out of range for Unicast Poll Retry. The

range is 0 to 10. Explanation The value of Unicast Poll Retry is a non-numeric value or is out

of range. Recommended Action Use numeric value for the Unicast Poll Retry and make sure the



This section contains the Server Config messages.

Error Message Error: Address is a mandatory field. Explanation The value of IPv4 address is a mandatory field. Recommended Action IP address has to be entered.

Error Message Incorrect input! Address must be a valid IP address. Explanation The value of IPv4 address is a invalid IP address Recommended Action Use a valid IP address to create a SNTP server.

Error Message Error: Failed to create New SNTP Server. Maximum allowable of

SNTP Servers already configured. Explanation User does not allowed to create more than 3 SNTP server in a

system. Recommended Action The maximum provided SNTP server in the system is 3. Please

remove a unused server and then add the new one to the system.

Error Message Error: Value (<value>) is out of range for Server Port. The valid

range is 1 to 65535. Explanation The value of Port is a non-numeric value or out of range 1 to

65535. Recommended Action Use numeric value for server port and make sure the value is in

the range of 1 to 65535.

Error Message Error: Value (<value>) is out of range for Server Precedence.

The valid range is 1 to 3. Explanation The value of Priority is a non-numeric value or out of range 1 to

3. Recommended Action Use numeric value for server precedence and make sure the


Error Message Error: Value (<value>) is out of range for Version running on

Server. The valid range is 1 to 4. Explanation The value of Version is a non-numeric value or out of range 1 to

4. Recommended Action Use numeric value for SNTP version and make sure the value is

in the range of 1 to 4.

Error Message Error: IPv6 Address format is invalid. Explanation The value of IPv6 address is a invalid IP address Recommended Action Use a valid IP address to create a SNTP server.



This section contains the Current Time messages.

Error Message Error: Failed to set Current Year. Explanation The value of Year is a non-numeric value or out of range 2000 to

2099. Recommended Action Use numberic value for the Year and make sure the value is in


Error Message Error: Failed to set Current Month. Explanation The value of Month is a non-numeric value or out of range 1 to

12. Recommended Action Use numeric value for current month and make sure the value is

in the range of 1 to 12.

Error Message Error: Failed to set Current Day. Explanation The value of Day is a non-numeric value or out of range 1 to 31. Recommended Action Use numeric value for current Day and make sure the value is in


Error Message Error: Failed to set Current Minute. Explanation The value of Minute is out of range 0 to 59. Recommended Action Use the value of Minute from 0 to 59.

Error Message Error: Failed to set Current Second. Explanation The value of Second is out of range 0 to 59. Recommended Action Use the value of Second from 0 to 59.


This section contains the Time Zone messages.

Error Message Error: Failed to set Time Zone Hours. Explanation The value of Time Zone Hours is out of range 0 to 12. Recommended Action Use the value for Time Zone Hours from 0 to 12.

Error Message Error: Failed to set Time Zone Minutes. Explanation The value of Time Zone Minutes is out of range 0 to 59. Recommended Action Use value for Time Zone Minutes from 0 to 59.

Error Message Error: Failed to set Time Zone Name. Explanation The value of Time Zone Name is failed to set. Recommended Action The length of Time Zone Name is from 1 to 63 characters.


4.1.8 UDLD

This section contains the UDLD Config

Error Message Error: Message format is invalid. Explanation The value of Message is not numbers or blank. Recommended Action Input a number for Message.

Error Message Error: Value (<value>) is out of range for Message. The valid

range is 7 to 90 Explanation The value of Message is out of range. Recommended Action Make sure the value is in the range of 7 to 90.


4.1.9 CDP

This section contains the Config messages.

Error Message Error: Failed to set CDP Hold Time. Explanation The value of Hold Time is non-numeric value or out of range 10

to 255. Recommended Action Use numeric value for CDP Hold Time and make sure the value

is in the range of 10 to 255.

Error Message Error: Failed to set CDP Transmit Time. Explanation The value of Transmit Interval is non-numeric value or out of

range 5 to 254. Recommended Action Use numeric value for CDP Transmit Time and make sure the



4.1.10 LLDP

This section contains the Global Config messages.

Error Message Error: Transmit Interval format is invalid. Explanation User input a non-numeric value for Transmit Interval. Recommended Action Use numeric value for Transmit Interval.

Error Message Error: Value (<value>) is out of range for Transmit Interval. The

valid range is 1 to 32768. Explanation The value of Transmit Interval is out of range 1 to 32768. Recommended Action The value of field should be in the range of 1 to 32768.

Error Message Error: Hold Multiplier format is invalid. Explanation User input a non-numeric value for Hold Multiplier. Recommended Action Use numeric value for Hold Multiplier.

Error Message Error: Value (<value>) is out of range for Hold Multiplier. The

valid range is 2 to 10. Explanation The value of Hold Multiplier is out of range 2 to 10. Recommended Action The value of field should be in the range of 2 to 10.

Error Message Error: Re-Initialization Delay format is invalid. Explanation User input a non-numeric value for the Re-Initialization Delay. Recommended Action Use numeric value for Re-Initialization Delay.

Error Message Error: Value (<value>) is out of range for Re-Initialization Delay.

The valid range is 2 to 10. Explanation The value of Re-Initialization Delay is out of range 1 to 10. Recommended Action The value of field should be in the range of 1 to 10.

Error Message Error: Notification Interval format is invalid. Explanation User input a non-numeric value for Notification Interval. Recommended Action Use numeric value for Notification Interval.

Error Message Error: Value (<value>) is out of range for Notification Interval.

The valid range is 2 to 10. Explanation The value of Notification Interval is out of range 5 to 3600. Recommended Action The value of field should be in range of 5 to 3600.


4.1.11 DHCP

This section contains the DHCP Client.

Error Message Error: Text string not entered Explanation The value of Test String is not entered when user select DHCP

Identifier with Specific Test String. Recommended Action This field can’t be empty.

Error Message Error: Incorrect input! Explanation The value of Hex value is incorrect format when use select

DHCP Identifier with Specific Hexadecimal value. Recommended Action Use the correct format for DHCP Identifier. The format should be

as 00:00:00:00:00:00.

Error Message Error: Hex value not entered Explanation The value of Hex value is not entered when use select DHCP

Identifier with Specific Hexadecimal value. Recommended Action This field can’t be empty.


4.1.12 DNS Relay

This section contains the DNS Relay Config messages.

Error Message Error: Failed to set Default Domain Name. You entered

<domainName>. The Domain Name is exist or more the 64 characters.

Explanation User configure a non alpha-numeric characters for Default Domain Name.

Recommended Action Use alpha-numeric characters to configure Default Domain Name, and the maximum length of Default Domain Name is 63 characters.

Error Message Error: Failed to set Domain Name. The Domain Name is exist or

more than 64 characters. Explanation User configure a non alpha-numeric characters for Domain

Name. Recommended Action Use alpha-numeric characters to configure Domain Name, and

the maximum length of Domain Name is 63 characters.


This section contains the Name Server Config messages

Error Message Error: Invalid IP Address ! Explanation The value of IP address of Name Server Config is incorrect. Recommended Action Use a valid IP address for Name Server.

Error Message Error: Invalid Ipv6 Address ! Explanation The value of IPv6 address of Name Server Config is incorrect. Recommended Action Use a valid IPv6 address for Name Server.

Error Message Error: Can't modify IP address of this Dynamic DNS Name

Server. Explanation The Name Server get by dhcp can not be changed. Recommended Action The Name Server get by dhcp can not be changed.

Error Message Error: Table is full for DNS Name Server. Explanation The Table for DNS Name Server is full. Recommended Action Remove unused Name Server.


This section contains the Hosts Config messages

Error Message Error: Invalid IP Address ! Explanation The value of IP address of Host Config is invalid. Recommended Action Use a valid IP address for Host.

Error Message Error: Invalid Ipv6 Address ! Explanation The value of IPv6 address of Name Server Config is incorrect. Recommended Action Use a valid IPv6 address for Name Server.

Error Message Error: Domain Name is a mandatory field. Explanation The value of Domain Name is a mandatory field. Recommended Action Input a Domain Name in this field.



4.1.13 sFlow

This section contains the sFlow Config messages.

Error Message Error! Receiver Owner String should be less than 128 charactersExplanation User configure a non alpha-numeric characters for Default

Domain Name. Recommended Action Use alpha-numeric characters to configure Receiver Owner

String, and the maximum length of Receiver Owner String is 128 characters.

Error Message Error! This Receiver should be unclaimed first Explanation check wheather user enterd same owner string or not this check

has to be done to avoid race condition Recommended Action This Receiver should be unclaimed first

Error Message Error! Failed to set Receiver Timeout Explanation Failed to set Receiver Timeout Recommended Action Receiver Timeout (0 to 4294967295 secs

Error Message Error! Please enter a non blank Receiver Owner String Explanation enter a blank Receiver Owner String Recommended Action enter a non blank Receiver Owner String

Error Message Error! Please enter a non zero Receiver Timeout value. Explanation enter a zero Receiver Timeout value Recommended Action enter a non zero Receiver Timeout value

Error Message Error! Failed to set Receiver Owner String should be less than

128 characters Explanation Receiver Owner String should be less than 128 characters Recommended Action the maximum length of Receiver Owner String is 128 characters.

Error Message Error! Invalid Receiver Maximum Datagram Size Explanation Invalid Receiver Maximum Datagram Size Recommended Action Receiver Maximum Datagram Size (200 to 9116 )

Error Message Error! Failed to set Receiver Maximum Datagram Size Explanation Failed to set Receiver Maximum Datagram Size Recommended Action Receiver Maximum Datagram Size (200 to 9116 )

Error Message Error! Invalid Receiver Port Explanation Invalid Receiver Port Recommended Action Receiver Port (1 to 65535 )

Error Message Error! Failed to set Receiver Port Explanation Failed to set Receiver Port Recommended Action Receiver Port (1 to 65535 )


Error Message Error! Failed to set Receiver Datagram Version Invalid Version Explanation Failed to set Receiver Datagram Version Invalid Version Recommended Action Version 5

Error Message Error! Failed to set Receiver Address Inavlid IP address Explanation Failed to set Receiver Address Inavlid IP address Recommended Action Check to see if the netowrk address is within the valid range of

addresses

Error Message Error! Failed to set Receiver Address invalid IPv6 address, can

not set IPv6 link local address Explanation Failed to set Receiver Address invalid IPv6 address, can not set

IPv6 link local address Recommended Action Check to see if the netowrk address is within the valid range of

addresses

Error Message Error! Failed to set Receiver Address Invalid IPv6 address. Explanation Failed to set Receiver Address Invalid IPv6 address. Recommended Action Check the Address Format

Error Message Error! Failed to set Receiver Address Explanation Failed to set Receiver Address Recommended Action Check the Address Format

Error Message Error! Invalid Receiver Index Explanation Invalid Receiver Index Recommended Action Check Receiver Index (1 to 8)

Error Message Error! Failed to set Receiver Index. Explanation Failed to set Receiver Index. Recommended Action Check Receiver Index (1 to 8)

Error Message Error! Invalid Poller Interval Explanation Failed to set Receiver Index. Recommended Action Poller Interval (0 to 86400 secs)

Error Message Error! Failed to set Poller Interval Explanation Failed to set Poller Interval Recommended Action Poller Interval (0 to 86400 secs)

Error Message Error! Delete poller config first Explanation Delete poller config first Recommended Action Delete poller config first

Error Message Error! Failed to delete Explanation Failed to delete Recommended Action Failed to delete

Error Message Error! Invalid Receiver Index


Explanation Invalid Receiver Index Recommended Action Receiver Index (1 to 8 )

Error Message Error! Invalid Sampling Rate Explanation Invalid Sampling Rate Recommended Action Sampling Rate (256 to 65536, 0 for disable )

Error Message Error! Failed to set Sampling Rate Explanation Failed to set Sampling Rate Recommended Action Sampling Rate (256 to 65536, 0 for disable )

Error Message Error! Invalid Maximum Header Size Explanation Invalid Maximum Header Size Recommended Action Maximum Header Size (20 to 256 )

Error Message Error! Failed to set Maximum Header Size Explanation Failed to set Maximum Header Size Recommended Action Maximum Header Size (20 to 256 )

Error Message Error! Inactive Receiver Explanation Inactive Receiver Recommended Action ALREADY CONFIGURED

Error Message Error! Maximum Samplers Limit exceeded Explanation Maximum Samplers Limit exceeded Recommended Action TABLE IS FULL

Error Message Error! Invalid Receiver index value Explanation Invalid Receiver index value Recommended Action Receiver Index (1 to 8 )

Error Message Error! Delete sampler config first. Explanation Delete sampler config first Recommended Action Delete sampler config first


4.2 Switching

4.2.1 Forwarding Database

This section contains the Forwarding Database module messages.

Error Message Error: Aging Interval (secs) format is invalid. Explanation The value of MAC address aging interval (secs) is non-numeric

value. Recommended Action Set MAC address aging interval (secs) with numeric value in the

range of 10 to 1000000.

Error Message Error: Value (<value>) is out of range for Aging Interval (secs).

The valid range is 10 to 1000000. Explanation The value of MAC address aging interval (secs) is out of range. Recommended Action Set MAC address aging interval (secs) with numeric value 10 to

1000000.

Error Message Error: MAC Address Search requires a MAC address in form

00:01:01:23:45:67:89:AB. Explanation The value of MAC address aging interval (secs) is out of range. Recommended Action Set MAC address in form 00:01:01:23:45:67:89:AB where 00:01

is the VLAN ID and 01:23:45:67:89:AB is the MAC address, to search in the forwarding database.


4.2.2 Port

This section contains the port module messages.

Error Message Error: Failed to set STP Mode.

Explanation User try to change the STP mode of the interface, but the interface doesn't exist in the system.

Recommended Action Refresh the WEB page, and select the interface again.

Error Message Error: Failed to set Capability.

Explanation User try to change the speed Capability of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Physical Mode.

Explanation User try to change the Physical mode of the interface, but the interface doesn't exist in the system.

Recommended Action Refresh the WEB page, and select the interface again

Error Message Error: Failed to set LACP Mode <interface identifier>.

Explanation User try to change the LACP mode of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Link Trap.

Explanation User try to change the Link Trap of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Admin Mode.

Explanation User try to change the Admin Mode of the interface, but the interface doesn't exist in the system.



Error Message Error: Failed to set Admin Mode. Interface <interface identifier>

was disabled by e-keying function. Explanation User try to enable a interface, but it is failed. The interface is

disabled by the e-Keying function. Recommended Action Check the e-Keying status of this interface first. User does not

allow to enable it while the e-Keying status is disabled. To enable the e-Keying, please refer to the MMB operations.

Error Message Error: Failed to set Admin Mode. This function is not allowed on

port-channel members <interface identifier>. Explanation User try to set Admin Mode on a prot-channel member, and it is

failed. Recommended Action To set the Admin Mode from the port-channel interface.

Error Message Error: Failed to set Port Description.

Explanation User try to change the Port Description of the interface, but the interface doesn't exist in the system.


Error Message Error: Maximum Frame Size format is invalid. Explanation The value of Port Maximum Frame Size is out of range. Recommended Action Set Port Maximum Frame Size with numeric value from 1518 to

9216.

Error Message Error: Value (<value>) is out of range for Maximum Frame Size.

The valid range is 1518 to 9216. Explanation The value of Port Maximum Frame Size is out of range. Recommended Action Set Port Maximum Frame Size with numeric value from 1518 to

9216.

Error Message Error: Failed to set STP Loop Guard Mode.

Explanation User try to change the STP Loop Guard Mode of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set STP Root Guard Mode.

Explanation User try to change the STP Root Guard Mode of the interface, but the interface doesn't exist in the system.



Error Message Error: Failed to set BPDU Filter.

Explanation User try to change the BPDU Filter of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set BPDU Guard.

Explanation User try to change the BPDU Guard of the interface, but the interface doesn't exist in the system.



This section contains the Mirroring module messages.

Error Message Error: You must select a destination port. Explanation The destination port is not selected. Recommended Action The destination port must be selected before enable port-mirror

function.


4.2.3 VLAN

This section contains the VLAN module messages.

Error Message Error: VLAN ID format is invalid. Explanation The value of VLAN ID is non-numeric value. Recommended Action Set VLAN ID with numeric value from 1 to 4094.

Error Message Error: Value (<value>) is out of range for VLAN ID. The valid

range is 1 to 4094. Explanation The value of VLAN ID is out of range. Recommended Action Set VLAN ID with numeric value 1 to 4094.

Error Message Error: Failed to create VLAN. VLAN already exists. Explanation The value of VLAN ID already existed. Recommended Action Create VLAN with other unconfigured VLAN ID.

Error Message Error: Failed to set <vlanName>. Vlan name must contain

alphaNumeric characters only. Explanation The VLAN name is non-alphanumeric characters. Recommended Action Create VLAN name with alphanumeric characters.

Error Message Error: Port Priority format is invalid. Explanation The value of Port Priority is non-numeric character. Recommended Action Set Port Priority with numeric character 0 to 7.

Error Message Error: Value (<value>) is out of range for Port Priority. The valid

range is 0 to 7. Explanation The value of Port Priority is out of range. Recommended Action Set Port Priority with numeric character 0 to 7.

Error Message Error: Failed to delete VLAN. Explanation The VLAN ID is not valid. Recommended Action Delete the valid VLAN ID.


4.2.4 Protocol-based VLAN

This section contains the Protocol-based VLAN module messages.

Error Message Error: Failed to set VLAN Group Name. Invalid name entered. Explanation The value of Protocol-based VLAN Group Name is blank. Recommended Action Set Protocol-based VLAN Group Name with up to 16

alphanumeric characters.

Error Message Error: Failed to set <vlanGroupName>. Vlan Group Name must

contain alphanumeric characters only. Explanation The value of VLAN Group Name is not alphanumeric character. Recommended Action Set VLAN Group Name with up to 16 alphanumeric characters.

Error Message Error: VLAN format is invalid. Explanation The value of Protocol-based VLAN ID is not numeric character. Recommended Action Set Protocol-based VLAN ID with numeric character 1 to 4094.

Error Message Error: Value (<value>) is out of range for VLAN. The valid range

is 1 to 4094. Explanation The value of Protocol-based VLAN ID is out of range. Recommended Action Set Protocol-based VLAN ID with numeric character 1 to 4094.

Error Message Error: The group already exists. Explanation The Protocol-based VLAN Group already exists. Recommended Action Create other Protocol-based VLAN Group which is not

configured.

Error Message Error: Failed to attach interface to Group ID. Interface already

configured with another group using the same protocol. Explanation The interface can not configured with the same protocol belong

to different VLAN Groups. Recommended Action Set other interfaces which is not attached to the same protocol of

different VLAN Groups.

Error Message Error: Failed to set Protocols. It is already configured with

another group(s) which are sharing ports of this group. Explanation The Protocol can not configured with the another VLAN Group

which is sharing the same port and VLAN ID. Recommended Action Set Protocol to other VLAN Group which is not sharing the same

port and VLAN ID.


4.2.5 IP Subnet-based VLAN

This section contains the IP Subnet-based VLAN module messages.


each octet(x) in the range 0-255. Explanation The IP address of IP Subnet-based VLAN is not in form x.x.x.x

with numeric character 0-255. Recommended Action Set IP address of IP Subnet-based VLAN in form x.x.x.x with

numeric character 0-255.

Error Message Error: Subnet Mask requires a subnet mask in x.x.x.x form. Explanation The IP Subnet Mask of IP Subnet-based VLAN is not in form

x.x.x.x with numeric character 0-255. Recommended Action Set IP Subnet Mask of IP Subnet-based VLAN in form x.x.x.x

with numeric character 0-255.

Error Message Error: Subnet mask must have contiguous ones and be no

longer than 30 bits. Explanation The IP Subnet Mask of IP Subnet-based VLAN is not contiguous

ones and over 30 bits in each octet form x.x.x.x. Recommended Action Set IP Subnet Mask of IP Subnet-based VLAN with contiguous

ones numeric character 0-255 and under 30 bits in each octet form x.x.x.x.

Error Message Error: The IP address and subnet mask combination is not valid. Explanation The IP address and Subnet Mask of IP Subnet-based VLAN is

not correct combination. Recommended Action Set IP address without reserved IP and Subnet Mask with

contiguous ones and under 30 bits in each octet form x.x.x.x.

Error Message Error: VLAN format is invalid. Explanation The value of IP Subnet-based VLAN ID is not numeric character.Recommended Action Set IP Subnet-based VLAN ID with numeric character 1 to 4094.


is 1 to 4094. Explanation The value of IP Subnet-based VLAN ID is out of range. Recommended Action Set IP Subnet-based VLAN ID with numeric character 1 to 4094.


Error Message Error: Failed to delete IP Subnet-based Vlan.

Explanation The IP Subnet-based VLAN does not exist . Recommended Action Delete the IP Subnet-based VLAN which is configured.


4.2.6 MAC-based VLAN

This section contains the MAC-based VLAN module messages.

Error Message Error: Locally Administered MAC Address requires a MAC

address in form 01:23:45:67:89:AB. Explanation The MAC address of MAC-based VLAN is not alphanumeric

character in form 01:23:45:67:89:AB. Recommended Action Set MAC address of MAC-based VLAN with 00 to ff

alphanumeric character in form 01:23:45:67:89:AB.

Error Message Error: The most significant byte of the MAC address should have

the mask xxxx xx10. Explanation The MAC address of MAC-based VLAN can not be

00:00:00:00:00:00. Recommended Action Set MAC address of MAC-based VLAN with 00 to ff

alphanumeric character excluding reserved MAC.

Error Message Invalid MAC Address! Explanation The MAC address of MAC-based VLAN can not be the reserved

MAC. Recommended Action Set MAC address of MAC-based VLAN with 00 to ff

alphanumeric character excluding reserved MAC.

Error Message Error: VLAN format is invalid. Explanation The value of MAC-based VLAN ID is not numeric character. Recommended Action Set MAC-based VLAN ID with numeric character 1 to 4094.


is 1 to 4094. Explanation The value of MAC-based VLAN ID is out of range. Recommended Action Set MAC-based VLAN ID with numeric character 1 to 4094.

Error Message Error: Failed to delete MAC-based VLAN.

Explanation The MAC-based VLAN does not exist . Recommended Action Delete the MAC-based VLAN which is configured.


4.2.7 GARP

This section contains the GARP module messages.

Error Message Error: Please disable VTP at first. Explanation The VTP Admin is not disabled before enable GVRP. Recommended Action The VTP Admin should be disabled before GVRP enabled .

Error Message Error: Join Timer (centisecs) format is invalid. Explanation The value of Join Timer (centisecs) is not numeric character. Recommended Action Set Join Timer (centisecs) with numeric character 10 to 100.

Error Message Error: Value (0) is out of range for Join Timer (centisecs). The

valid range is 10 to 100. Explanation The value of Join Timer (centisecs) is out of range. Recommended Action Set Join Timer (centisecs) with numeric character 10 to 100.

Error Message Error: Leave Timer (centisecs) format is invalid. Explanation The value of Leave Timer (centisecs) is not numeric character. Recommended Action Set Leave Timer (centisecs) with numeric character 20 to 600.

Error Message Error: Value (<value>) is out of range for Leave Timer

(centisecs). The valid range is 20 to 600. Explanation The value of Leave Timer (centisecs) is out of range. Recommended Action Set Leave Timer (centisecs) with numeric character 20 to 600.

Error Message Error: Leave All Timer (centisecs) format is invalid. Explanation The value of Leave All Timer (centisecs) is not numeric

character. Recommended Action Set Leave All Timer (centisecs) with numeric character 200 to

6000.

Error Message Error: Value (<value>) is out of range for Leave All Timer

(centisecs). The valid range is 200 to 6000. Explanation The value of Leave All Timer (centisecs) is out of range. Recommended Action Set Leave All Timer (centisecs) with numeric character 200 to

6000.


4.2.8 VTP

This section contains the VTP module messages.

Error Message Domain name must contain alphaNumeric characters only! Explanation The Domain name is not alphanumeric characters. Recommended Action Set Domain name with alphanumeric characters.

Error Message Fail to set V2 Mode. Explanation The device can not enable VTP V2 mode. The VTP 'Device

Mode' is not set to 'Server' mode. Recommended Action The VTP 'Device Mode' should be set to 'Server' mode fisrt, and

then enable the VTP V2 Mode.


4.2.9 IGMP Snooping


Error Message Error: IGMP Query Interval (secs) format is invalid.

Error: Failed to set IGMP Query Interval (secs). You entered 0. Explanation The value of IGMP Query Interval (secs) is not numeric

character. Recommended Action Set IGMP Query Interval (secs) with numeric character 2 to

3600.

Error Message Error: Value (<value>) is out of range for IGMP Query Interval

(secs). The valid range is 2 to 3600. Error: Failed to set IGMP Query Interval (secs). You entered (<value>).

Explanation The value of IGMP Query Interval (secs) is out of range. Recommended Action Set IGMP Query Interval (secs) with numeric character 2 to

3600.

Error Message Error: IGMP Report Delay (secs) format is invalid. Explanation The value of IGMP Report Delay (secs) is not numeric character.Recommended Action Set IGMP Query Interval (secs) with numeric character 2 to

3600.

Error Message Error: Value (<value>) is out of range for IGMP Report Delay

(secs). The valid range is 1 to Group Membership Interval -1. Explanation The value of IGMP Report Delay (secs) is out of range. Recommended Action Set IGMP Report Delay (secs) with numeric character 1 to

Group Membership Interval -1.

Error Message Error: IGMP Query Timeout (secs) format is invalid. Explanation The value of IGMP Query Timeout (secs) is not numeric

character. Recommended Action Set IGMP Query Timeout (secs) with numeric character 0 to

3600.

Error Message Error: Value (<value>) is out of range for IGMP Query Timeout

(secs). The valid range is 0 to 3600. Explanation The value of IGMP Report Delay (secs) is out of range. Recommended Action Set IGMP Query Timeout (secs) with numeric character 0 to

3600.


Error Message Error: VLAN ID format is invalid. Explanation The value of IGMP Snooping VLAN ID is not numeric character. Recommended Action Set IGMP Snooping VLAN ID with numeric character 1 to 4094.

Error Message Error: Value (<value>) is out of range for Vlan ID. The valid

range is 1 to 4094. Explanation The value of IGMP Snooping VLAN ID is out of range. Recommended Action Set IGMP Snooping VLAN ID with numeric character 1 to 4094.

Error Message Error: Group Membership Interval format is invalid. Explanation The value of IGMP Snooping Group Membership Interval is not

numeric character. Recommended Action Set IGMP Snooping Group Membership Interval with numeric

character (Maximum Response Time + 1) to 3600.

Error Message Error: Value (<value>) is out of range for Group Membership

Interval. The valid range is 2 to 3600. Explanation The value of IGMP Snooping Group Membership Interval is out

of range. Recommended Action Set IGMP Snooping Group Membership Interval with numeric

character 2 to 3600.

Error Message Error: Maximum Response Time format is invalid. Explanation The value of IGMP Snooping Maximum Response Time is not

numeric character. Recommended Action Set IGMP Snooping Maximum Response Time with numeric

character 1 to (Group Membership Interval -1).

Error Message Error: Value (<value>) is out of range for Maximum Response

Time. The valid range is 1 to (Group Membership Interval -1). Explanation The value of IGMP Snooping Maximum Response Time is out of

range. Recommended Action Set IGMP Snooping Maximum Response Time with numeric


Error Message Error: Multicast Router Expiry Time format is invalid. Explanation The value of IGMP Snooping Multicast Router Expiry Time is not

numeric character. Recommended Action Set IGMP Snooping Multicast Router Expiry Time with numeric



Error Message Error: Value (<value>) is out of range for Multicast Router Expiry

Time. The valid range is 0 to 3600. Explanation The value of IGMP Snooping Multicast Router Expiry Time is out

of range. Recommended Action Set IGMP Snooping Multicast Router Expiry Time with numeric


Error Message Error: Failed to set Snooping Querier Address. Explanation The invalid IP address can not set for IGMP Snooping Querier

Address. Recommended Action Set IGMP Snooping Querier Address with valid IP address.

Error Message Error: IGMP Version format is invalid. Explanation The value of IGMP Version is not numeric character. Recommended Action Set IGMP Version with numeric character 1 to 2.

Error Message Error: Value (<value>) is out of range for IGMP Version. The

valid range is 1 to 2. Explanation The value of IGMP Version is out of range. Recommended Action Set IGMP Version with numeric character 1 to 2.

Error Message Error: Query Interval format is invalid. Explanation The value of IGMP Query Interval is not numeric character. Recommended Action Set IGMP Query Interval with numeric character 1 to 1800.

Error Message Error: Value (input) is out of range for Query Interval. The valid

range is 1 to 1800. Explanation The value of IGMP Query Interval is out of range. Recommended Action Set IGMP Query Interval with numeric character 1 to 1800.

Error Message Error: Querier Expiry Interval format is invalid. Explanation The value of IGMP Querier Expiry Interval is not numeric

character. Recommended Action Set IGMP Querier Expiry Interval with numeric character 60 to

300.

Error Message Error: Value (<value>) is out of range for Querier Expiry Interval.

The valid range is 60 to 300. Explanation The value of IGMP Querier Expiry Interval is out of range. Recommended Action Set IGMP Querier Expiry Interval with numeric character 60 to

300.


Error Message Error: VLAN ID format is invalid. Explanation The value of IGMP Snooping Querier VLAN ID is not numeric

character. Recommended Action Set IGMP Snooping Querier VLAN ID with numeric character 1

to 4094.


range is 1 to 4094. Explanation The value of IGMP Snooping Querier VLAN ID is out of range. Recommended Action Set IGMP Snooping Querier VLAN ID with numeric character 1

to 4094.

Error Message Error:IGMP ADMIN must be enabled. Explanation IGMP ADMIN is not enabled. Recommended Action IGMP ADMIN must be enabled before configuring the setting.

Error Message Error: There are no ports assignment. Explanation There are no ports assigned to IGMP Multicast Static Group. Recommended Action Assign ports to IGMP Multicast Static Group.

Error Message Error: You cannot define L2Mcast Group for these MAC

addresses from 01:00:5E:00:00:00 to 01:00:5E:00:00:FF Explanation The reserved Multicast MAC addresses can not be set for IGMP

Multicast Static Group. Recommended Action Create IGMP Multicast Static Group with non-reserved Multicast

MAC address.

Error Message Error: MAC Address requires a MAC address in form

01:00:5e:xx:xx:xx. Explanation User input an invalid format or non-multicast MAC address for

IGMP Multicast Static Group setting. Recommended Action Use the correct multicast MAC address for this function, MAC

address should be in 01:00:5e:xx:xx:xx format where range for x is 0 - F.

Error Message Error: Failed to create MAC Filter.

ERROR: Filter already exists. Explanation User create a IGMP Multicast Static Group, but the MAC

address is already configured in the system. Recommended Action Use another multicast MAC address to create the new IGMP

Static Group.


Error Message Error: Failed to delete Multicast Static. Explanation The Multicast MAC address is not assigned to IGMP Multicast

Static Group. Recommended Action Delete the Multicast MAC address which is configured for IGMP

Multicast Static Group.


4.2.10 MLD Snooping

This section contains the MLD module messages.

Error Message Error: Failed to set Group Membership Interval (secs). You

entered 0. Explanation The value of MLD Group Membership Interval (secs) is not

numeric character. Recommended Action Set MLD Group Membership Interval (secs) with numeric


Error Message Error: Failed to set Group Membership Interval (secs). You

entered (<value>). Explanation The value of MLD Group Membership Interval (secs) is out of

range. Recommended Action Set MLD Group Membership Interval (secs) with numeric


Error Message Error: Maximum Response Time format is invalid. Explanation The value of MLD Snooping Maximum Response Time is not

numeric character. Recommended Action Set MLD Snooping Maximum Response Time with numeric



Time. The valid range is 1 to (Group Membership Interval -1). Explanation The value of IGMP Snooping Maximum Response Time is out of

range. Recommended Action Set IGMP Snooping Maximum Response Time with numeric


Error Message Error: Multicast Router Present ExpirationTime (secs) format is

invalid. Explanation The value of MLD Snooping Multicast Router Present

ExpirationTime is not numeric character. Recommended Action Set MLD Snooping Multicast Router Present ExpirationTime with

numeric character 0 to 3600.

Error Message Error: Value (<value>) is out of range for Multicast Router

Present ExpirationTime (secs). The valid range is 0 to 3600. Explanation The value of MLD Snooping Multicast Router Present

ExpirationTime is out of range. Recommended Action Set MLD Snooping Multicast Router Present ExpirationTime with

numeric character 0 to 3600.


Error Message Error: VLAN ID format is invalid. Explanation The value of MLD Snooping VLAN ID is not numeric character. Recommended Action Set MLD Snooping VLAN ID with numeric character 1 to 4094.


range is 1 to 4094. Explanation The value of MLD Snooping VLAN ID is out of range. Recommended Action Set MLD Snooping VLAN ID with numeric character 1 to 4094.

Error Message Error! Group Membership Interval (secs) format is invalid. Explanation The value of Group Membership Interval (secs) is not numeric

character. Recommended Action Set Group Membership Interval (secs) with numeric character 2

to 3600.

Error Message Error! Value (<value>) is out of range for Group Membership

Interval (secs). The valid range is 2 to 3600. Explanation The value of Group Membership Interval (secs) is out of range. Recommended Action Set Group Membership Interval (secs) with numeric character 2

to 3600.


Time. The valid range is 1 to 3599. Explanation The value of MLD Snooping Maximum Response Time is out of

range. Recommended Action Set MLD Snooping Maximum Response Time with numeric


Error Message Error! Invalid combination of values for Group Membership

Interval and Maximum Response Time. Explanation The value of combination of MLD Group Membership Interval

and Maximum Response Time is invalid. Recommended Action Set MLD Group Membership Interval (secs) with numeric

character (Maximum Response Time +1) to 3600. Set MLD Snooping Maximum Response Time with numeric character 1 to (Group Membership Interval -1).

Error Message Error: Multicast Router Expiry Time format is invalid. Explanation The value of MLD Snooping Multicast Router Expiry Time is not

numeric character. Recommended Action Set MLD Snooping Multicast Router Expiry Time with numeric



Error Message Error: Value (<value>) is out of range for Multicast Router Expiry

Time. The valid range is 0 to 3600. Explanation The value of MLD Snooping Multicast Router Expiry Time is out

of range. Recommended Action Set MLD Snooping Multicast Router Expiry Time with numeric


Error Message Error: Invalid Snooping Querier Address. Explanation The invalid IPv6 address can not set for MLD Snooping Querier

address. Recommended Action Set MLD Snooping Querier Address with valid IPv6 address in

form fe80:x:x:x:x:x:x:x and fe80::x .

Error Message Snooping Querier Address requires a IPv6 address in form

fe80:x:x:x:x:x:x:x and fe80::x. Explanation The IPv6 address of MLD Snooping Querier is out of range. Recommended Action Set MLD Snooping Querier Address with valid IPv6 address in


Error Message The support IPv6 formats are fe80:x:x:x:x:x:x:x and fe80::x. Explanation The supported IPv6 address formats for MLD Snooping Querier. Recommended Action Set MLD Snooping Querier Address with valid IPv6 address in


Error Message Error: Query Interval format is invalid. Explanation The value of MLD Query Interval is not numeric character. Recommended Action Set MLD Query Interval with numeric character 1 to 1800.

Error Message Error: Value (<value>) is out of range for Query Interval. The

valid range is 1 to 1800. Explanation The value of MLD Query Interval is out of range. Recommended Action Set MLD Query Interval with numeric character 1 to 1800.

Error Message Error: Querier Expiry Interval format is invalid. Explanation The value of MLD Querier Expiry Interval is not numeric

character. Recommended Action Set MLD Querier Expiry Interval with numeric character 60 to

300.


Error Message Error: Invalid Snooping Querier VLAN Address. Explanation The invalid IPv6 address can not set for MLD Snooping Querier

VLAN address. Recommended Action Set MLD Snooping Querier VLAN address with valid IPv6

address in form fe80:x:x:x:x:x:x:x and fe80::x .

Error Message Snooping Querier VLAN Address requires a IPv6 address in

form fe80:x:x:x:x:x:x:x and fe80::x. Explanation The IPv6 address of MLD Snooping Querier is out of range. Recommended Action Set MLD Snooping Querier Address with valid IPv6 address in


Error Message Error: There are no ports assignment. Explanation There are no ports assigned to MLD Multicast Static Group. Recommended Action Assign ports to MLD Multicast Static Group.

Error Message Error: MLD ADMIN must be enable. Explanation MLD ADMIN is not enabled. Recommended Action MLD ADMIN must be enabled before configuring the setting.


33:33:xx:xx:xx:xx. Explanation Only Multicast MAC addresses can be set for MLD Multicast

Static Group. Recommended Action Create MLD Multicast Static Group with non-reserved Multicast

MAC address.

Error Message Error: You cannot define L2Mcast Group for these MAC

addresses from 33:33:00:00:00:00 to 33:33:00:00:00:FF Explanation The reserved Multicast MAC addresses can not be set for MLD

Multicast Static Group. Recommended Action Create MLD Multicast Static Group with non-reserved Multicast

MAC address.

Error Message Error: Failed to create MAC Filter.

ERROR: Filter already exists. Explanation User try to add a MLD Multicast Static Group, but the MLD

Multicast Static Group has already existed. Recommended Action Check the MLD Multicast Static Group setting or use another

multicast MAC address to create the new MLD Static Group.


Error Message Error: Failed to delete Multicast Static. Explanation The Multicast MAC address is not assigned to MLD Multicast

Static Group. Recommended Action Delete the Multicast MAC address which is configured for MLD

Multicast Static Group.


4.2.11 Multicast Forwarding Database

This section contains the Multicast Forwarding Database module messages.

Error Message Error: MAC Address requires an 8 bytes MAC address in form

00:01:01:23:45:67:89:AB, where the first 2 bytes represent a VLAN ID. The VLAN ID can be 0.

Explanation The MAC address is not valid form for MFDB Table. Recommended Action Set MAC address with 8 bytes MAC address in form

00:01:01:23:45:67:89:AB and the first 2 bytes must be a VLAN ID to search in MFDB Table.


4.2.12 Port-Channel

This section contains the Port-Channel module messages.

Error Message Error: Failed to set <portChannelName>. Port Channel Name

must contain alphaNumeric characters only. Explanation The Port Channel Name is not alphanumeric character. Recommended Action Set Port Channel Name with up to 15 alphanumeric character.

Error Message Error: Failed to create lag. Valid name not specified. Explanation The Port Channel Name is blank. Recommended Action Assign the Port Channel Name with up to 15 alphanumeric

character before creating the port-channel interface.

Error Message Error: This port-channel name already exists. Explanation The port-channel name is already used. Recommended Action Set other port-channel name which is not configuerd.

Error Message Error: Failed to set Port Channel. Explanation There are 64 maximum Port Channels already created. Recommended Action Reduce other unnecessary Port Channel. Maximum supported

port-channel is 64.

Error Message Error: This port channel is an up stream port of link state group.

Internal ports can't be its member. Explanation The port-channel is set to be the upstream port of a link state

group. So, the internal port can not be the member of a uplink port-channel.

Recommended Action Add internal port to be the member of the downlink port-channel.

Error Message Error: This port channel is a downstream port of link state group.

External ports can't be its member. Explanation The port-channel is set to be the downstream of a link state

group. So, the external port can not be the member of a downstream port-channel.

Recommended Action Add external port to be the member of the uplink port-channel.

Error Message <interface_identifier> is already a member of another LAG. Explanation The interface is already attached to another port-channel. Recommended Action Remove the interface from other port-channel and then add it to

the new port channel.


Error Message Error: Failed to delete Port Channel. This port channel is

configured as link state upstream. Explanation The port-channel configured as upstream of a link state group

can not be deleted. Recommended Action Remove the port-channel from link state group first.

Error Message Error: Failed to set Port Channel. Interface:

<interface_identifier> is configured as link state down stream. Explanation The interface attached to link state downstream can not be set to

be the member of a port channel. Recommended Action Remove the interface from link state group before adding it to a

port-channel or attach other interface to the port-channel.


<interface_identifier> is configured as link state up stream. Explanation The interface attached to link state upstream can not be set to be

the member of a port channel. Recommended Action Remove the interface from link state group before adding it to a



<interface_identifier> is configured as port backup. Explanation The interface attached to port backup group can not be set to be

the member of a port-channel. Recommended Action Remove the interface from port backup group before adding it to

a port-channel or attach other interface to the port-channel.

Error Message Error: Failed to set Member Ports. LACP Mode must be enabled

on member ports before they can be added to a Port Channel. Explanation The interface can not be added to a port-channel if the LACP

Mode is disabled on this interface. Recommended Action Enable the interface LACP Mode before adding it to a

port-channel.

Error Message Error: Failed to create Port Channel Members : Full-duplex is

needed. Explanation The interface can not be added to a port-channel if half-duplex

Mode is set or operated on this interface. Recommended Action Set the interface to operate at Full-duplex Mode before adding it

to a port-channel.


Error Message Error: Failed to create Port Channel Members : Speed is not

matched. Explanation The interface can not be added to a port-channel if Speed is not

matched. Recommended Action Set the interface to match the current operated speed of the

port-channel before adding to the port-channel.

Error Message Error: Failed to create Port Channel Members. Explanation The interface used by other module can not be added to a

port-channel. Recommended Action Remove the interface from other module before adding to the

port-channel.

Error Message Error: Failed to add all members to Port Channel. Member limit

exceeded. Explanation The Port Channel members reach maximum members. The

maximum number of the port-channel member is 8. Recommended Action Remove unnecessary members from port-channel first.

Error Message Error: Failed to create Port Channel Members : Type is not

matched. Explanation The type of the interface is different from the configured

members of a port-channel. For example, a port-channel has a 10G type interface member, you can’t add the 1G type interface to it.

Recommended Action To add the same type interface to a port-channel.

Error Message Error: Failed to delete Port Channel. Explanation The Port Channel interface is invalid. Recommended Action Refresh the WEB page, and select the interface again.


4.2.13 Spanning-Tree

This section contains the Spanning-Tree module messages.

Error Message Error: Failed to set Configuration Name. You entered

<config_name>. Explanation The Spanning-Tree configuration Name is blank. Recommended Action Create Spanning-Tree configuration Name with up to 32

characters.

Error Message Error: Configuration Revision Level format is invalid. Explanation The value of Spanning-Tree Configuration Revision Level is not

numeric character. Recommended Action Set Spanning-Tree Configuration Revision Level with numeric


Error Message Error: Value (<value>) is out of range for Configuration Revision

Level. The valid range is 0 to 65535. Explanation The value of Spanning-Tree Configuration Revision Level is out

of range. Recommended Action Set Spanning-Tree Configuration Revision Level with numeric


Error Message Error: Bridge Priority format is invalid. Explanation The value of Spanning-Tree Bridge Priority is not numeric

character. Recommended Action Set Spanning-Tree Bridge Priority with numeric character 0 to

61440.

Error Message Error: Value (<value>) is out of range for Bridge Priority. The

valid range is 0 to 61440. Explanation The value of Spanning-Tree Bridge Priority is out of range. Recommended Action Set Spanning-Tree Configuration Revision Level with numeric


Error Message Error: Bridge Max Age (secs) format is invalid. Explanation The value of Spanning-Tree Bridge Max Age (secs) is not

numeric character. Recommended Action Set Spanning-Tree Configuration Revision Level with numeric

character 6 to 40.


Error Message Error: Value (<value>) is out of range for Bridge Max Age (secs).

The valid range is 6 to 40. Explanation The value of Spanning-Tree Bridge Max Age (secs) is out of

range. Recommended Action Set Spanning-Tree Bridge Max Age (secs) with numeric

character 6 to 40.

Error Message Error: Bridge Hello Time (secs) format is invalid. Explanation The value of Spanning-Tree Bridge Hello Time (secs) is not

numeric character. Recommended Action Set Spanning-Tree Bridge Hello Time (secs) with numeric

character 1 to 10.

Error Message Error: Value (<value>) is out of range for Bridge Hello Time

(secs). The valid range is 1 to 10. Explanation The value of Spanning-Tree Bridge Hello Time (secs) is out of

range. Recommended Action Set Spanning-Tree Bridge Hello Time (secs) with numeric

character 1 to 10.

Error Message Error: Bridge Forward Delay (secs) format is invalid. Explanation The value of Spanning-Tree Bridge Forward Delay (secs) is not

numeric character. Recommended Action Set Spanning-Tree Bridge Forward Delay (secs) with numeric

character 4 to 30.

Error Message Error: Value (<value>) is out of range for Bridge Forward Delay

(secs). The valid range is 4 to 30. Explanation The value of Spanning-Tree Bridge Forward Delay (secs) is out

of range. Recommended Action Set Spanning-Tree Bridge Forward Delay (secs) with numeric

character 4 to 30.

Error Message Invalid field in MAX hops. Explanation The value of Spanning-Tree Bridge MAX hops is not numeric

character. Recommended Action Set Spanning-Tree MAX hops with numeric character 1 to 127.

Error Message Bridge Max Hops : Field Out of Range. Explanation The value of Spanning-Tree Bridge Max Hops is out of range. Recommended Action Set Spanning-Tree Bridge Max Hops with numeric character 1 to

127.


Error Message Error: Could not create the MST instance. Explanation The Spanning-Tree MST ID already existed. Recommended Action Create Spanning-Tree MST ID which is not used.

Error Message Error: MST ID format is invalid. Explanation The value of Spanning-Tree MST ID is not numeric character. Recommended Action Set Spanning-Tree MST ID with numeric character 1 to 4094.

Error Message Error: Value (<value>) is out of range for MST ID. The valid

range is 1 to 4094. Explanation The value of Spanning-Tree MST ID is out of range. Recommended Action Set Spanning-Tree MST ID with numeric character 1 to 4094.

Error Message Error: Priority format is invalid. Explanation The value of Spanning-Tree MST Priority is not numeric

character. Recommended Action Set Spanning-Tree MST Priority with numeric character 0 to

61440.

Error Message Error: Value (<value>) is out of range for Priority. The valid range

is 0 to 61440. Explanation The value of Spanning-Tree MST Priority is out of range. Recommended Action Set Spanning-Tree MST Priority with numeric character 0 to

61440.

Error Message Error: Failed to set Priority. You entered <priority_value>. Explanation The Spanning-Tree MST Priority is associated with invalid

instance. Recommended Action Refresh the WEB page, and select the instance again.

Error Message Error: Priority was set successfully to a value in accordance with

IEEE 802.1s specifications. Explanation User input a wrong Spanning-tree Priority, system will change to

the correct value automatically, and pop-up the warning message.

Recommended Action No recommended action. According to the IEEE802.1s

specification, the priority is a multiple of 4096. For example, 0,

4096, 8192, and the default priority is 32768.


Error Message At least one VLAN now associated with this instance was

previously associated with another instance. Explanation One or more VLANs associated with different instances. Recommended Action Remove the VLAN from other instance.

Error Message Error: Failed to delete MST ID. Explanation The Spanning-Tree MST ID is invalid. Recommended Action Delete the valid Spanning-Tree MST ID.

Error Message Error: Port Priority format is invalid. Explanation The value of Spanning-Tree CST Port Priority is not numeric

character. Recommended Action Set Spanning-Tree CST Port Priority with numeric character 0 to

240.


range is 0 to 240. Explanation The value of Spanning-Tree CST Port Priority is out of range. Recommended Action Set Spanning-Tree CST Port Priority with numeric character 0 to

240.

Error Message Error: Port Path Cost format is invalid. Explanation The value of Spanning-Tree CST Port Path Cost is not numeric

character. Recommended Action Set Spanning-Tree CST Port Path Cost with numeric character 0

to 200000000.

Error Message Error: Value (<value>) is out of range for Port Path Cost. The

valid range is 0 to 200000000. Explanation The value of Spanning-Tree CST Port Path Cost is out of range. Recommended Action Set Spanning-Tree CST Port Path Cost with numeric character 0

to 200000000.

Error Message Inid format in the external path cost. Explanation The value of Spanning-Tree CST Port Path Cost is not numeric

character. Recommended Action Set Spanning-Tree CST Port Path Cost with numeric character 0

to 200000000.



valid range is 0 to 200000000. Explanation The value of Spanning-Tree CST Port Path Cost is out of range. Recommended Action Set Spanning-Tree CST Port Path Cost with numeric character 0

to 200000000.

Error Message Error: Failed to set Port Priority. Explanation The interface is not valid to set Port Priority. Recommended Action Refresh the WEB page, and select the interface again.

Error Message Error: Failed to set Admin Edge Port. Explanation The interface is not valid to set Admin Edge Port. Recommended Action Refresh the WEB page, and select the interface again.

Error Message Failed to Set External Path Cost. Explanation The interface is not valid to set External Path Cost. The interface

might be deleted from other UI. Recommended Action Refresh the WEB page, and select the interface again.

Error Message Error: Failed to set BPDU Migration Check. Could not force

BPDU migration check. Explanation User try to force the port to send out 802.1w or 802.1d BPDUs,

but the Spanning-tree protocol still using 802.1d(STP). Recommended Action User should change the Spanning-tree mode to 802.1w(RSTP)

or 802.1s(MSTP), and then click 'Force' button of the interface in CST Port tab.

Error Message Error: Port Priority format is invalid. Explanation The value of Spanning-Tree MST Port Priority is not numeric

characters. Recommended Action Set Spanning-Tree MST Port Priority with numeric character 0 to

240.


range is 0 to 240. Explanation The value of Spanning-Tree MST Port Priority is out of range. Recommended Action Set Spanning-Tree MST Port Priority with numeric character 0 to

240.


Error Message Error: Port Path Cost format is invalid. Explanation The value of Spanning-Tree MST Port Path Cost is not numeric

characters. Recommended Action Set Spanning-Tree MST Port Path Cost with numeric character 0

to 200000000.


valid range is 0 to 200000000. Explanation The value of Spanning-Tree MST Port Path Cost is out of range.Recommended Action Set Spanning-Tree MST Port Path Cost with numeric character 0

to 200000000.

Error Message Error: Failed to set Port Priority. Explanation The Spanning-Tree MST ID or the interface is invalid. Recommended Action Refresh the WEB page, and select the MST ID or interface

again.

Error Message Error: Failed to set Port Path Cost. You entered

<port_path_cost>. Explanation The Spanning-Tree MST ID is invalid. Recommended Action Refresh the WEB page, and select the MST ID again.


4.2.14 Link-State


Error Message Error: Please disable this group first. Explanation The Link-State upstream port can not be modified if group mode

is enabled. Recommended Action Disable Link-State group mode first before modifying upstream

port.

Error Message Error: Failed to set. This function is not allowed on port-channel

members. Explanation The port-channel member can not set to Link-State group. Recommended Action Remove the interface from port-channel or attach other interface

to Link-State group.

Error Message Error: Failed to delete Group. Explanation The Link-State Group is invalid. Recommended Action Refresh the WEB page, and select the group again.

Error Message Error: Failed to set. Group Id is not existed. Explanation The Link-State Group is invalid.. Recommended Action Refresh the WEB page, and select the group again.


4.2.15 Port-backup


Error Message The active port should be different from the backup port. Explanation The active port and backup port of Port-backup function can not

be set to use the same interface. Recommended Action Use different interface rather than the backup port for the active

port.

Error Message Error: Failed to set Active Port. Explanation The interface can not set to be active port. Recommended Action Set active port with the interface which is not used by other

module.

Error Message Error: Failed to set Backup Port. Explanation The interface can not set to be backup port. Recommended Action Set backup port with the interface which is not used by other

module.

Error Message Error: port pair should be configured before enabling this group. Explanation The active port and backup port have to be configured before

you enable this group. Recommended Action Configure the active port and backup port before enabling group

mode.

Error Message Error: Failed to set Group ID. Explanation There are already 6 maximum Port-backup Group existed. For

stacking switch, the maximum 32 port-backup group is supported.

Recommended Action Reduce/Remove other unnecessary Port-backup group.


4.2.16 MAC Filter

This section contains MAC Filter module messages.


01:23:45:67:89:AB. Explanation The MAC address is invalid alphanumeric characters for MAC

filter. Recommended Action Set MAC address for MAC filter with 00 to ff alphanumeric

characters in xx:xx:xx:xx:xx:xx form.

Error Message Error: Failed to set MAC Address. Mac Address is restricted. Explanation The MAC address is invalid for MAC filter. Recommended Action Set MAC address for MAC filter with 00 to ff in xx:xx:xx:xx:xx:xx

form, excluding the reserved MAC address.

Error Message Error: Failed to create MAC Filter. Explanation The MAC Filter is already exists. Recommended Action Create other MAC Filter which is not configured.

Error Message Error: Failed to delete MAC Filter. Explanation The MAC Filter is not exists. It might be deleted from other UI. Recommended Action Refresh the WEB page, and select the MAC Filter again.


4.3 Group Administration (IBP)

4.3.1 Uplink-Set

This section contains the Uplink-Set module messages.

Error Message Error: Failed to set <uplinkSetName>. Uplink Set name must

contain alphanumeric characters only, and can't be empty. Explanation It is failed to create a Uplink Set while the name is not

alphanumeric characters. Recommended Action To Create a Uplink Set, the uplink set name have to be

alphanumeric characters and can not be empty. The Uplink Set name can not contain “default” string.

Error Message Error to set group backup!! Explanation The Uplink Set name is invalid. Recommended Action Refresh the WEB page, and select the uplink set name again.

Error Message Error to set link state!! Explanation The Uplink Set name is invalid. Recommended Action Refresh the WEB page, and select the uplink set name again.

Error Message Error to set IGMP Snooping!! Explanation The Uplink Set name is invalid. Recommended Action Refresh the WEB page, and select the uplink set name again.

Error Message Error to set LACP!! Explanation The Uplink Set name is invalid. Recommended Action Refresh the WEB page, and select the uplink set name again.

Error Message Error: Failed to delete Uplink Set <uplinkSetName>. Explanation The Uplink Set name is invalid. Recommended Action Refresh the WEB page, and select the uplink set name again.

Error Message Error: Failed to create Uplink Set. Uplink Set already exists. Explanation The Uplink Set name already exists. Recommended Action Create the Uplink Set name which is not used.


Error Message Error: Failed to create Uplink Set. Uplink Set table is full. Explanation Maximum 30 Uplink Sets have been configured in the system. Recommended Action Reduce/Remove the unused Uplink Set.

Error Message Error: Failed to delete Uplink Set <uplinkSetName>. It is used by

groups. Explanation The Uplink Set is used by other group. For example, it is used by

Port Group, VLAN port group, Service LAN or Service VLAN. Recommended Action Remove the Uplink Set from the groups which are using it.


4.3.2 Port-Group

This section contains the Port-Group module messages.

Error Message Error: Failed to set <portGroupName>. Port Group name must

contain alphanumeric characters only, and can't be empty. Explanation It is failed to create a Port Group while the name is not

alphanumeric characters. Recommended Action Use alphanumeric characters for the Port Group name to create

a Port Group and the name can not be empty. The Port Group name can not contain “default” string.

Error Message Error: Failed to delete <portGroupName>. Explanation The Port Group name is invalid. Recommended Action Refresh the WEB page, and select the Port Group name again.

Error Message Error: Failed to create Port Group. Port Group already exists. Explanation The Port Group name already exists. Recommended Action Create the Port Group with a name which is not used in the

system.

Error Message Error: Can't set Port Group member <interface_identifier>. Explanation The interface is already used by other Port Group. Recommended Action Remove the used interface from the Port Group.

Error Message Error: Failed to set <portGroupName>. Explanation There are maximum 36 Port Groups already configured. Recommended Action Reduce/Remove the unnecessary Port Group.

Error Message Error: Failed to set <uplinkSetName>. Explanation The uplink-set does’t existed to set for Port Group. Recommended Action Refresh the WEB page and select a valid uplink-set for the Port

Group.


4.3.3 VLAN Port-Group

This section contains the VLAN Port-Group module messages.

Error Message Error: Failed to set <vlanGroupName>. VLAN Port Group name

must contain alphanumeric characters only, and can't be empty. Explanation It is failed to create a VLAN Port Group while the name is not

alphanumeric characters. Recommended Action Use alphanumeric characters for the VLAN Port Group name to

create a VLAN Port Group and the name can not be empty.

Error Message Error: Failed to delete <vlanGroupName>. Explanation The VLAN Port Group name is invalid. Recommended Action Refresh the WEB page, and select the VLAN Port Group Name

again.

Error Message Error: Failed to create VLAN Port Group. VLAN Port Group

already exists. Explanation The VLAN Port Group already existed. Recommended Action Create the VLAN Port Group with a name which is not used in

the system.

Error Message Error: Can't set the same VLAN ID on uplink set

<uplinkSetName>. Explanation The VLAN Port Group can’t use this VLAN ID which is used by

on group with the same uplink set. Recommended Action Use the different VLAN ID for VLAN Port Group.

Error Message Error: Value <vlanId> is out of range for VLAN ID. The valid

range is 1 to 4094. Explanation The value of VLAN Port Group VLAN ID is out of range. Recommended Action Set the value of VLAN Port Group VLAN ID with numeric


Error Message Error: Uplink set <uplinkSetName> is used by other module. Explanation The Uplink set is already used by other module. Recommended Action Remove the Uplink set from the used module or set other Uplink

for this VLAN Port Group.


Error Message Error: Can't set VLAN Port Group member <interface_identifier>.Explanation The interface is already used by other Group. Recommended Action Remove the interface from the other Group or set other interface

to VLAN Port Group.

Error Message Error: Failed to remove VLAN Port Group member for

<interface_identifier>. Explanation The interface is invalid to remove from VLAN Port Group. It

might be removed from other UI. Recommended Action Refresh the WEB page, and select the interface again.

Error Message Error: Can't create a new VLAN Port Group because there is no

valid Uplink Set. Explanation There is no Uplink Set available for VLAN Port Group. Recommended Action Create new Uplink Set for VLAN Port Group.

Error Message Uplink Set <uplinkSetName> does not exist! Explanation The Uplink Set does not exist to set for VLAN Port Group. Recommended Action Refresh the WEB page, and select the uplink set field again.


4.3.4 Service LAN

This section contains the Service LAN module messages.

Error Message Error: Failed to set <svcLanName>. Service LAN name must

contain alphaNumeric characters only, and can't be empty. Explanation It is failed to create a Service LAN Group while the name is not

alphanumeric characters. Recommended Action Use alphanumeric characters for the Service LAN Group name

to create a Service LAN Group and the name can not be empty.


<uplinkSetName>. Explanation The Service LAN Group can’t use this VLAN ID which is used by

on group with the same uplink set. Recommended Action Use the different VLAN ID for Service LAN Group.

Error Message Error: Failed to delete <svcLanName>. Explanation The Service LAN name is invalid. Recommended Action Refresh the WEB page, and select the service LAN name again.

Error Message Error: Failed to create Service LAN. Service LAN already exists. Explanation The Service LAN already existed. Recommended Action Create the Service LAN with a name which is not used in the

system.


range is 1 to 4094. Explanation The input VLAN ID of Service LAN is out of range. Recommended Action Set VLAN ID of Service LAN with numeric character 1 to 4094.

Error Message Error: Uplink set <uplinkSetName> is used by other module. Explanation The Uplink set is already used by other module. Recommended Action Remove the Uplink set from the used module or set other Uplink

for Service LAN.

Error Message Error: Interface <interface_identifier> has been used. Explanation The interface is already used by other Group. Recommended Action Remove the interface from the other Group or set other interface

to Service LAN.


Error Message Error: Can't create a new Service LAN because there is no valid

Uplink Set. Explanation There is no Uplink Set available for Service LAN. Recommended Action Create new Uplink Set for Service LAN.

Error Message Uplink Set <uplinkSetName> does not exist! Explanation The Uplink Set does not exist to set for Service LAN. Recommended Action Refresh the WEB page, and select the uplink set name again.


4.3.5 Service VLAN

This section contains the Service VLAN module messages.

Error Message Error: Failed to set <svcVlanName>. Service VLAN name must

contain alphaNumeric characters only, and can't be empty. Explanation It is failed to create a Service VLAN Group while the name is not

alphanumeric characters. Recommended Action Use alphanumeric characters for the Service VLAN Group name

to create a Service VLAN Group and the name can not be empty.


<uplinkSetName>. Explanation The Service VLAN Group can’t use this VLAN ID which is used

by on group with the same uplink set. Recommended Action Use the different VLAN ID for Service VLAN Group.

Error Message Error: Failed to delete <svcVlanName>. Explanation The Service VLAN name is invalid. Recommended Action Refresh the WEB page and select the service VLAN name

again.

Error Message Error: Failed to create Service VLAN. Service VLAN already

exists. Explanation The Service VLAN already existed. Recommended Action Create the Service VLAN with a name which is not used in the

system.


range is 1 to 4094. Explanation The input VLAN ID of Service VLAN is out of range. Recommended Action Set the VLAN ID of Service VLAN with numeric character 1 to

4094.

Error Message Error: Interface <interface_identifier> has been used. Explanation The interface is already used by other Group. Recommended Action Remove the interface from the other Group or set other interface

to Service VLAN.


Error Message Uplink Set <uplinkSetName> does not exist! Explanation The Uplink Set does not exist to set for Service VLAN. Recommended Action Refresh the WEB page and select the uplink set name again.


4.3.6 Port

This section contains the port module messages.

Error Message Error: Failed to set Capability.

Explanation User try to change the speed Capability of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Physical Mode.

Explanation User try to change the Physical mode of the interface, but the interface doesn't exist in the system.

Recommended Action Refresh the WEB page, and select the interface again

Error Message Error: Failed to set LACP Mode <interface identifier>.

Explanation User try to change the LACP mode of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Link Trap.

Explanation User try to change the Link Trap of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Admin Mode.

Explanation User try to change the Admin Mode of the interface, but the interface doesn't exist in the system.


Error Message Error: Failed to set Admin Mode. Interface <interface identifier>

was disabled by e-keying function. Explanation User try to enable a interface, but it is failed. The interface is

disabled by the e-Keying function. Recommended Action Check the e-Keying status of this interface first. User does not

allow to enable it while the e-Keying status is disabled. To enable the e-Keying, please refer to the MMB operations.


Error Message Error: Failed to set Admin Mode. This function is not allowed on

port-channel members <interface identifier>. Explanation User try to set Admin Mode on a prot-channel member, and it is

failed. Recommended Action To set the Admin Mode from the port-channel interface.

Error Message Error: Failed to set Port Description.

Explanation User try to change the Port Description of the interface, but the interface doesn't exist in the system.


Error Message Error: Maximum Frame Size format is invalid. Explanation The value of Port Maximum Frame Size is out of range. Recommended Action Set Port Maximum Frame Size with numeric value from 1518 to

9216.

Error Message Error: Value (<value>) is out of range for Maximum Frame Size.

The valid range is 1518 to 9216. Explanation The value of Port Maximum Frame Size is out of range. Recommended Action Set Port Maximum Frame Size with numeric value from 1518 to

9216.

This section contains the Mirroring module messages.

Error Message Error: You must select a destination port. Explanation The destination port is not selected. Recommended Action The destination port must be selected before enable port-mirror

function.


4.3.7 Port-Channel

This section contains the Port-Channel module messages.

Error Message Error: Failed to set <portChannelName>. Port Channel Name

must contain alphaNumeric characters only. Explanation The Port Channel Name is not alphanumeric character. Recommended Action Set Port Channel Name with up to 15 alphanumeric character.

Error Message Error: Failed to create lag. Valid name not specified. Explanation The Port Channel Name is blank. Recommended Action Assign the Port Channel Name with up to 15 alphanumeric

character before creating the port-channel interface.

Error Message Error: This port-channel name already exists. Explanation The port-channel name is already used. Recommended Action Set other port-channel name which is not configuerd.

Error Message Error: Failed to set Port Channel. Explanation There are 64 maximum Port Channels already created. Recommended Action Reduce other unnecessary Port Channel. Maximum supported

port-channel is 64.

Error Message Error: This port channel is an up stream port of link state group.

Internal ports can't be its member. Explanation The port-channel is set to be the upstream port of a link state

group. So, the internal port can not be the member of a uplink port-channel.

Recommended Action Add internal port to be the member of the downlink port-channel.

Error Message Error: This port channel is a downstream port of link state group.

External ports can't be its member. Explanation The port-channel is set to be the downstream of a link state

group. So, the external port can not be the member of a downstream port-channel.

Recommended Action Add external port to be the member of the uplink port-channel.

Error Message <interface_identifier> is already a member of another LAG. Explanation The interface is already attached to another port-channel. Recommended Action Remove the interface from other port-channel and then add it to

the new port channel.


Error Message Error: Failed to delete Port Channel. This port channel is

configured as link state upstream. Explanation The port-channel configured as upstream of a link state group

can not be deleted. Recommended Action Remove the port-channel from link state group first.


<interface_identifier> is configured as link state down stream. Explanation The interface attached to link state downstream can not be set to

be the member of a port channel. Recommended Action Remove the interface from link state group before adding it to a



<interface_identifier> is configured as link state up stream. Explanation The interface attached to link state upstream can not be set to be

the member of a port channel. Recommended Action Remove the interface from link state group before adding it to a



<interface_identifier> is configured as port backup. Explanation The interface attached to port backup group can not be set to be

the member of a port-channel. Recommended Action Remove the interface from port backup group before adding it to

a port-channel or attach other interface to the port-channel.

Error Message Error: Failed to set Member Ports. LACP Mode must be enabled

on member ports before they can be added to a Port Channel. Explanation The interface can not be added to a port-channel if the LACP

Mode is disabled on this interface. Recommended Action Enable the interface LACP Mode before adding it to a

port-channel.

Error Message Error: Failed to create Port Channel Members : Full-duplex is

needed. Explanation The interface can not be added to a port-channel if half-duplex

Mode is set or operated on this interface. Recommended Action Set the interface to operate at Full-duplex Mode before adding it

to a port-channel.


Error Message Error: Failed to create Port Channel Members : Speed is not

matched. Explanation The interface can not be added to a port-channel if Speed is not

matched. Recommended Action Set the interface to match the current operated speed of the

port-channel before adding to the port-channel.

Error Message Error: Failed to create Port Channel Members. Explanation The interface used by other module can not be added to a

port-channel. Recommended Action Remove the interface from other module before adding to the

port-channel.

Error Message Error: Failed to add all members to Port Channel. Member limit

exceeded. Explanation The Port Channel members reach maximum members. The

maximum number of the port-channel member is 8. Recommended Action Remove unnecessary members from port-channel first.

Error Message Error: Failed to create Port Channel Members : Type is not

matched. Explanation The type of the interface is different from the configured

members of a port-channel. For example, a port-channel has a 10G type interface member, you can’t add the 1G type interface to it.

Recommended Action To add the same type interface to a port-channel.

Error Message Error: Failed to delete Port Channel. Explanation The Port Channel interface is invalid. Recommended Action Refresh the WEB page, and select the interface again.

Error Message Error: Failed to set Port Channel. Interface <interface_identifier>

is configured as memeber of a Port Group. Explanation The interface configured as Port Group memeber can not set to

be port-channel memeber. Recommended Action Remove the interface from Port Group before adding it to the

port-channel.



is configured as memeber of a VLAN Port Group. Explanation The interface configured as VLAN Port Group memeber can not

set to be port-channel memeber. Recommended Action Remove the interface from VLAN Port Group before adding it to

the port-channel.


is configured as Service VLAN. Explanation The interface configured as Service VLAN memeber can not set

to be port-channel memeber. Recommended Action Remove the interface from Service VLAN before adding it to the

port-channel.


is configured as Service LAN. Explanation The interface configured as Service LAN memeber can not set to

be port-channel memeber. Recommended Action Remove the interface from Service LAN before adding it to the

port-channel.


4.3.8 Link-State


Error Message Error: Please disable this group first. Explanation The Link-State upstream port can not be modified if group mode

is enabled. Recommended Action Disable Link-State group mode first before modifying upstream

port.

Error Message Error: Failed to set. This function is not allowed on port-channel

members. Explanation The port-channel member can not set to Link-State group. Recommended Action Remove the interface from port-channel or attach other interface

to Link-State group.

Error Message Error: Failed to delete Group. Explanation The Link-State Group is invalid. Recommended Action Refresh the WEB page, and select the group again.

Error Message Error: Failed to set. Group Id is not existed. Explanation The Link-State Group is invalid.. Recommended Action Refresh the WEB page, and select the group again.


4.3.9 Port-backup


Error Message The active port should be different from the backup port. Explanation The active port and backup port of Port-backup function can not

be set to use the same interface. Recommended Action Use different interface rather than the backup port for the active

port.

Error Message Error: Failed to set Active Port. Explanation The interface can not set to be active port. Recommended Action Set active port with the interface which is not used by other

module.

Error Message Error: Failed to set Backup Port. Explanation The interface can not set to be backup port. Recommended Action Set backup port with the interface which is not used by other

module.

Error Message Error: port pair should be configured before enabling this group. Explanation The active port and backup port have to be configured before

you enable this group. Recommended Action Configure the active port and backup port before enabling group

mode.

Error Message Error: Failed to set Group ID. Explanation There are already 6 maximum Port-backup Group existed. For

stacking switch, the maximum 32 port-backup group is supported.

Recommended Action Reduce/Remove other unnecessary Port-backup group.


4.4 Security

4.4.1 Port Access Control

This section contains Port Access Control module messages.

Error Message Error: Server Timeout (secs) format is invalid. Explanation User uses non-numeric characters for Server Timeout. Recommended Action Use numeric character to configure Server Timeout.

Error Message Error: Value (<value>) is out of range for Server Timeout (secs).

The valid range is 1 to 65535. Explanation The value of Server Timeout is out of range. Recommended Action The range for Server Timeout is 1 to 65535.

Error Message Error: Maximum Requests format is invalid. Explanation User uses non-numeric characters for Maximum Requests. Recommended Action Use numeric character to configure Maximum Requests.

Error Message Error: Value (<value>) is out of range for Maximum Requests.

The valid range is 1 to 10. Explanation The value of Maximum Requests is out of range. Recommended Action To set the value of Maximum Requests in the range of 1 to 10.

Error Message Error: Reauthentication Period (secs) format is invalid. Explanation User uses non-numeric characters for Reauthentication Period. Recommended Action To set the value of Reauthentication Period in the range of 1 to

65535.

Error Message Error while trying to initialize port Explanation User try to Initialize the 802.1x function of a interface, but the

802.1x global Administrative Mode does not enable. Recommended Action User should enable the 802.1x global Administrative Mode, and

then Initialize the 802.1x interface.

Error Message Error while trying to reauthenticate port Explanation User try to Reauthenticate the 802.1x function of a interface, but

the 802.1x global Administrative Mode does not enable. Recommended Action User should enable the 802.1x global Administrative Mode, and

then Reauthenticate the 802.1x interface.


Error Message Error: Quiet Period (secs) format is invalid. Explanation User uses non-numeric characters for Quiet Period. Recommended Action Use numeric character to configure Quiet Period.

Error Message Error: Value (<value>) is out of range for Quiet Period (secs).

The valid range is 0 to 65535. Explanation The value of Quiet Period is out of range. Recommended Action The range of Quiet Period is 0 to 65535.

Error Message Error: Transmit Period (secs) format is invalid. Explanation User uses non-numeric characters for Transmit Period. Recommended Action Use numeric character to configure Transmit Period.

Error Message Error: Value (<value>) is out of range for Transmit Period (secs).

The valid range is 1 to 65535. Explanation The value of Transmit Period is out of range. Recommended Action The range of Transmit Period is 1 to 65535.

Error Message Error: Supplicant Timeout (secs) format is invalid. Explanation User uses non-nueric characters for Supplicant Timeout. Recommended Action Use numeric character to configure Supplicant Timeout.

Error Message Error: Value (<value>) is out of range for Supplicant Timeout

(secs). The valid range is 1 to 65535. Explanation The value of Supplicant Timeout is out of range. Recommended Action The range of Supplicant Timeout is 1 to 65535.


4.4.2 Port Security

This section contains Port Security module messages.

Error Message Error: Port Security Dynamic Limit format is invalid. Explanation User uses non-numeric characters for Dynamic Limit. Recommended Action Use numeric character for Dynamic Limit.

Error Message Error: Value (<value>) is out of range for Dynamic Limit. The

valid range is 0 to 600. Explanation The value of dynamic limit is out of range. Recommended Action The range of Dynamic Limit is 0 to 600.

Error Message Error: Port Security Static Limit format is invalid. Explanation User use non-numeric characters for Static Limit. Recommended Action Use numeric character for Static Limit.

Error Message Error: Value (<value>) is out of range for Port Security Static

Limit. The valid range is 0 to 20. Explanation The value of Maximum Number of Statically Locked MAC

Addresses Allowed is out of range. Recommended Action The range of Maximum Number of Statically Locked MAC

Addresses Allowed is 0 to 20.


01:23:45:67:89:AB. Explanation The character of Static MAC Address is not hexadecimal form. Recommended Action To set Static MAC address with hexadecimal character 1 to F.

(xx:xx:xx:xx:xx:xx)

Error Message Error: Failed to add Port Security Static MAC Address Explanation The Static MAC Address is already configured. Recommended Action Create other Static MAC Address which is not used.

Error Message Error: VLAN ID format is invalid. Explanation User uses non-numeric characters for VLAN ID. Recommended Action Use numeric character for VLAN ID.


Error Message Error: Value (<value>) is out of range for VLAN ID. The valid

range is 1 to 4094. Explanation The value of VLAN ID is out of range. Recommended Action The range of VLAN ID is 1 to 4094.

Error Message Error: Failed to delete Port Security Static MAC Address. Explanation User try to delete the Static MAC address, but the Static MAC

address is not configured. Recommended Action Refresh the WEB page, and select the static MAC address to be

deleted again.


4.4.3 RADIUS

This section contains RADIUS module messages.

Error Message Error: Server Host Address format is invalid. Explanation User try to set the IP address of the Server Host, but the field is

not filled. Recommended Action Use a valid IP address to set the address of Server Host.

Error Message Error: Invalid IP Address Explanation User try to set IP address for RADIUS accounting server, but the

IP address is invalid. Recommended Action Use a valid IP address to configure RADIUS accounting server.

Error Message Error: Port format is invalid. Explanation User uses non-numeric characters for the Port.Recommended Action Use the numeric character for the Port.


0 to 65535. Explanation The value of account port Interval is out of range. Recommended Action The range fo the account port Interval is is 0 - 65535.

Error Message Error: Failed to set Secret. The secret must be an alphanumeric

sequence with a maximum length of 16. Explanation User try to set Secret for RADIUS server, but the length of input

Secret is exceeded 16 characters. Recommended Action Use alphanumeric characters for Secret with the maximum legth

of 16.

Error Message Error: Max Number of Retransmits format is invalid. Explanation User try to configure the Max Number of Retransmits with a

non-alphanumeric characters. Recommended Action Use alphanumeric character for Max Number of Retransmits.

Error Message Error: Value (<value>) is out of range for Max Number of

Retransmits. The valid range is 1 to 15. Explanation User configures the Max Number of Retransmits is out of range.Recommended Action Use the range from 1 to 15 to configure Max Number of

Retransmits.


Error Message Error: Timeout Duration (secs) format is invalid. Explanation User try to configure the Timeout Duration with a

non-alphanumeric characters. Recommended Action Use alphanumeric character for Timeout Duration.

Error Message Error: Value (<value>) is out of range for Timeout Duration

(secs). The valid range is 1 to 30. Explanation The Timeout Duration is out of range.Recommended Action Use the range from 1 to 30 for Timeout Duration.

Error Message Error: Dead Time format is invalid. Explanation User try to configure the Dead Time with a non-alphanumeric

characters. Recommended Action Use alphanumeric character for Dead Time.

Error Message Error: Value (<value>) is out of range for Dead Time. The valid

range is 1 to 255. Explanation The Dead Time is out of range.Recommended Action Use the range from 1 to 30 for Dead Time.


each octet(x) in the range 0-255. Explanation User input an IP address with non-numeric character for

RADIUS Attribute 4 setting. Recommended Action Use numeric character 0-255 in x.x.x.x form for RADIUS

Attribute 4( NAS-IP Address).

Error Message Error: IP Address format is invalid. Explanation User input an reserved IP address for RADIUS Attribute 4

( NAS-IP Address). For example, 0.0.0.0 / 255.255.255.255 / 224.xxx.xxx.xxx / 127.0.0.1.

Recommended Action Use the correct IP Address for RADIUS Attribute 4( NAS-IP Address).

Error Message Error: Could not add radius server Explanation The IP address of the RADIUS server is already configured. Recommended Action Use another IP address for RADIUS server.


Error Message Error: Port format is invalid. Explanation User try to configure the Port with a non-alphanumeric

characters. Recommended Action Use alphanumeric character for Port.


0 to 65535. Explanation The Port is out of range.Recommended Action Use the range from 1 to 30 for Port.

Error Message Error: Failed to set Secret. The secret must be an alphanumeric

sequence with a maximum length of 16. Explanation User try to set Secret for a Accouting server, but the length of

input Secret is exceeded 16 characters. Recommended Action Use alphanumeric characters for Secret with the maximum legth

of 16.

Error Message Error: IPv6 Address format is invalid. Explanation The value of IPv6 address of Radius Attribute 95 is incorrect. Recommended Action Use a valid IPv6 address for Radius Attribute 95.

Error Message Error: Address must be a valid IP address. Explanation The input IPv4 address is invalid. Recommended Action Use a valid IPv4 address.

Error Message Error: Not a valid Host Name. Explanation The input Host Name is invalid. IP address in this field is invalid. Recommended Action Use a valid Host Name.

Error Message Error: Not a valid IPv6 Address. Explanation The input IPv6 address is invalid. Recommended Action Use a valid IPv6 address.


4.4.4 TACACS+

This section contains TACACS+ module messages.

Error Message Error: Failed to set Key String. Length of Key String is greater

than 128 characters Explanation User try to configure the Key String, but the it is exceeded 128

alphanumeric characters in length. Recommended Action Use up to 128 alphanumeric characters for the Key String.

Error Message Error: Connection Timeout format is invalid. Explanation The value of Connection Timeout is not numeric character. Recommended Action Use numeric character for Connection Timeout.

Error Message Error: Value (<value>) is out of range for Connection Timeout.

The valid range is 1 to 30. Explanation The value of Connection Timeout is out of range. Recommended Action The value of Connection Timeout is in the range of 1 to 30.

Error Message Error: Server Host Address format is invalid. Explanation User try to configure the host name for the TACACS server, but

it is exceeded 63 alphanumeric characters in length. Recommended Action The length of the host name of TACACS server is up to 63

alphanumeric characters in length.

Error Message Error: Invalid IP Address Explanation User input an invalid or reserved IP address for TACACS+

server. Recommended Action Use the valid IP address for this function. IP address should be

in a.b.c.d format where range for a, b, c, and d is 1-255.

Error Message Invalid IP address! Explanation User input an IP address for TACACS+ server, but the IP

address has existed in the TACACS+ server list. Recommended Action Check the TACACS+ server IP address, and use the correct IP

address to add new TACACS+ server entry.

Error Message Error: Priority format is invalid. Explanation User try to configure Priority with non-numeric characters. Recommended Action Use numeric characters for Priority.


Error Message Error: Value (<value>) is out of range for Priority. The valid range

is 0 to 65535. Explanation The value of Priority is out of range. Recommended Action The range of Priority is from 0 to 65535.

Error Message Error: Port format is invalid. Explanation User try to configure Port with non-numeric characters. Recommended Action Use numeric characters for Port.


0 to 65535. Explanation The value of Port is out of range. Recommended Action The range of Port is from 0 to 65535.

Error Message Error: Connection Timeout format is invalid. Explanation User try to configure Connection Timeout with non-numeric

characters. Recommended Action Use numeric characters for Connection Timeout.

Error Message Error: Value (<value>) is out of range for Connection Timeout.

The valid range is 1 to 30. Explanation The value of Connection Timeout is out of range. Recommended Action The range of Connection Timeout is 1 to 30.

Error Message Error: IPv6 Address format is invalid. Explanation The value of IPv6 address of Radius Attribute 95 is incorrect. Recommended Action Use a valid IPv6 address for Radius Attribute 95.

Error Message Error: Address must be a valid IP address. Explanation The input IPv4 address is invalid. Recommended Action Use a valid IPv4 address.

Error Message Error: Not a valid Host Name. Explanation The input Host Name is invalid. IP address in this field is invalid. Recommended Action Use a valid Host Name.

Error Message Error: Not a valid IPv6 Address. Explanation The input IPv6 address is invalid. Recommended Action Use a valid IPv6 address.


4.4.5 LDAP

This section contains LDAP module messages.

Error Message Error: Invalid IP Address Explanation User configure the LDAP server with an invalid IP address. Recommended Action Use a valid IP address for LDAP server.


1 to 65535. Explanation The value of LDAP server TCP port is out of range. Recommended Action The range of LDAP server TCP port is 1 to 65535.


4.4.6 Access Control Lists

This section contains IP ACL module messages.

Error Message Error: IP ACL ID format is invalid. Explanation User try to configure a ACL with non-numeric IP ACL ID. Recommended Action Configure Standard IP ACL ID with numeric character from 1 to

99 and Extended IP ACL ID with numeric character from 100 to 199.

Error Message Error! Invalid IP ACL name string. Explanation User try to creat a IP ACL Name, but it is failed. Recommended Action To create IP ACL Name within 31 characters include alphabetic,

numeric, dash, dot or underscore characters only and start with a letter.

Error Message Error! Unable to rename Access List. Explanation User try to rename a IP ACL Name, but it is failed. Recommended Action To rename IP ACL Name within 31 characters include

alphabetic, numeric, dash, dot or underscore characters only and start with a letter.

Error Message Error! IP ACL Name already exists. Explanation User try to rename a IP ACL Name, but it is failed. Recommended Action To rename the IP ACL Name with a non-exist IP ACL Name.

Error Message Error: Value(<value>) IP ACL. ACL ID already in use. The valid

range is 1 to 99. Explanation The value of Standard IP ACL ID is out of range. Recommended Action To create a ACL with Standard IP ACL ID within 1 to 99.

Error Message Error: Value(<value>) IP ACL. ACL ID already in use. The valid

range is 100 to 199. Explanation The value of Extended IP ACL ID is out of range. Recommended Action To create a ACL with Extended IP ACL ID within 100 to 199.

Error Message Error: Failed to create IP ACL. ACL ID already in use. Explanation User try to configure a ACL with IP ACL ID, but the IP ACL ID is

already used in the system. Recommended Action Use other unused IP ACL ID for the new IP ACL.


Error Message Error: Failed to create IP ACL. Explanation User try to configure a new IP ACL, but the maximum 100 ACLs

are already reached. Recommended Action Reduce/Remove other unnecessary IP/MAC ACLs .

Error Message Error: Value(<value>) is out of range for Rule ID.The valid range

is 1 to 10. Explanation The value of IP ACL Rule ID is out of range. Recommended Action The range of IP ACL Rule ID is 1 to 10.

Error Message Error: The Rule ID is already configured. Explanation User try to configure a IP ACL Rule ID for IP ACL, but the Rule

ID is already configured in the system. Recommended Action Use other unused IP ACL Rule ID.

Error Message Error: Failed to delete ACL. Explanation The IP ACL ID does not existed. Recommended Action Refresh the WEB page, and select the IP ACL ID again.

Error Message Error: Rule ID format is invalid. Explanation User try to configure a IP ACL Rule ID with non-numeric

characters. Recommended Action Use numeric characters for IP ACL Rule ID.

Error Message Error: Assign Queue ID format is invalid. Explanation User try to configure IP ACL Assign Queue ID with non-numeric

characters. Recommended Action Use numeric characters for IP ACL Assign Queue ID.

Error Message Please configure the protocol keyword first. Explanation User attempt to set the IP address of extended IP ACL Rule, but

it is failed without setting the protocol keyword first. Recommended Action The protocol keyword has to be configured before setting IP

address of extended IP ACL Rule.

Error Message Error: Failed to delete Rule. Explanation The IP ACL Rule ID does not existed. Recommended Action Refresh the WEB page and select the IP ACL Rule ID again.


Error Message Error: Value (<value>) is out of range for Assign Queue ID. The

valid range is 0 to 7. Explanation The value of IP ACL Assign Queue ID is out of range. Recommended Action The range of IP ACL Assign Queue ID is 0 to 7.

Error Message Error: Protocol Number format is invalid. Explanation User try to configure the IP ACL Protocol Number with

non-numeric characters. Recommended Action Use numeric characters for IP ACL Protocol Number.

Error Message Error: Value (<value>) is out of range for Protocol Number. The

valid range is 0 to 255. Explanation The value of Protocol Number is out of range. Recommended Action The range of IP ACL Protocol Number is 0 to 255.

Error Message Error: Source IP Address requires an IP address in x.x.x.x form

with each octet(x) in the range 0-255. Explanation User input the Source IP Address with non-numeric characters

or out of range. Recommended Action Use numeric characters 0-255 in x.x.x.x form for Source IP

Address.

Error Message Error: Source Wildcard Mask requires a subnet mask in x.x.x.x

form. Explanation User input the Source IP Wildcard Mask with non-numeric

characters or out of range. Recommended Action Use numeric characters 0-255 in x.x.x.x form for Source IP

Wildcard Mask.

Error Message Error: Source L4 Port Number format is invalid. Explanation User try to configure Source L4 Port Number with non-numeric

characters. Recommended Action Use numeric characters for IP ACL Source L4 Port Number.

Error Message Error: Value (<value>) is out of range for Source L4 Port

Number. The valid range is 0 to 65535. Explanation The value of Source L4 Port Number is out of range. Recommended Action The range of IP ACL Source L4 Port Number is 0 to 65535.

Error Message Error: Destination IP Address requires an IP address in x.x.x.x


form with each octet(x) in the range 0-255. Explanation User input the Destination IP Address with non-numeric

characters or out of range. Recommended Action Use numeric characters 0-255 in x.x.x.x form for Destination IP

Address.

Error Message Error: Destination Wildcard Mask requires a subnet mask in

x.x.x.x form. Explanation User input the Destination IP Wildcard Mask with non-numeric

characters or out of range. Recommended Action Use numeric characters 0-255 in x.x.x.x form for Destination IP

Wildcard Mask.

Error Message Error: Destination L4 Port Number format is invalid. Explanation User try to configure Destination L4 Port Number with

non-numeric characters. Recommended Action Use numeric characters for IP ACL Destination L4 Port Number.

Error Message Error: Value (<value>) is out of range for Destination L4 Port

Number. The valid range is 0 to 65535. Explanation The value of Destination L4 Port Number is out of range. Recommended Action The range fo IP ACL Destination L4 Port Number is 0 to 65535.

Error Message Error: Value (<value>) is out of range for IP DSCP. The valid

range is 0 to 63. Explanation The value of IP DSCP is out of range. Recommended Action The range of IP DSCP Number of IP ACL is 0 to 63.

Error Message Error: IP Precedence format is invalid. Explanation User try to configure IP Precedence Number with non-numeric

characters. Recommended Action Use numeric characters for IP Precedence Number of IP ACL.

Error Message Error: Value (<value>) is out of range for IP Precedence. The

valid range is 0 to 7. Explanation The value of IP Precedence is out of range. Recommended Action The range of IP Precedence Number of IP ACL is 0 to 7.

Error Message Error: TOS Bits format is invalid. Explanation User try to configure TOS Bits with non-numeric characters. Recommended Action Use numeric characters for TOS Bits of IP ACL.


Error Message Error: TOS Mask format is invalid. Explanation User try to configure TOS Mask with non-numeric characters. Recommended Action Use numeric characters for TOS Mask of IP ACL.


This section contains MAC ACL module messages.

Error Message Error: Failed to create MAC ACL. Invalid ACL Name. Name

string may include alphabetic, numeric, dash, dot or underscore characters only. Name must start with a letter and the size of the name string must be less than or equal to 31 characters.

Explanation User try to creat a MAC ACL, but it is failed. Recommended Action To create MAC ACL Name within 31 characters include

alphabetic, numeric, dash, dot or underscore characters only and start with a letter.

Error Message Error: Failed to create MAC ACL. Explanation User try to configure a new MAC ACL, but the maximum 100

ACLs are already reached. Recommended Action Reduce/Remove other unnecessary IP/MAC ACLs .

Error Message Error: Failed to create MAC ACL. ACL Name already exists Explanation User try to create a MAC ACL, but the MAC ACL Name is

already used in the system. Recommended Action Use other MAC ACL Name which is not used in the system to

create the new MAC ACL.

Error Message Error: Value (<value>) is out of range for Rule ID. The valid

range is 1 to 10. Explanation The value of MAC ACL Rule ID is out of range. Recommended Action The range fo MAC ACL Rule ID is 1 to 10.

Error Message Error: Failed to set Match Every. Explanation User try to configure the MAC ACL Rule ID, but the selected

MAC ACL name does not exist. Recommended Action Refresh the WEB page, and select the correct MAC ACL name

again.

Error Message Error: Failed to create MAC ACL. MAC ACL could not be

renamed. Explanation User try to rename a MAC ACL, but the entry of MAC ACL name

is invalid or blank or the original name does not exist in the system.

Recommended Action 1. Rename the MAC ACL within 31 characters include alphanumeric, dash, dot or underscore characters only and start with a letter. 2. Refresh the WEB page, and select the correct MAC ACL name again.


Error Message Error: The Rule ID is already configured. Explanation User try to create a MAC ACL Rule ID, but it is already

configured in the system. Recommended Action Use other MAC ACL Rule ID which is not used in the system to

create new Rule ID.

Error Message Error: Failed to delete Rule. Explanation The MAC ACL Rule ID does not existed. Recommended Action Refresh the WEB page, and select the MAC ACL Rule ID again.

Error Message Error: Assign Queue ID format is invalid. Explanation User try to configure MAC ACL Assign Queue ID with

non-numeric characters. Recommended Action Use numeric characters for MAC ACL Assign Queue ID.

Error Message Error: Value (<value>) is out of range for Assign Queue ID. The

valid range is 0 to 7. Explanation The value of MAC ACL Assign Queue ID is out of range. Recommended Action The range of MAC ACL Assign Queue ID is 0 to 7.

Error Message Error: Value (<value>) is out of range for COS value. The valid

range is 0 to 7. Explanation The value of MAC ACL COS is out of range. Recommended Action The range of MAC ACL COS is 0 to 7.

Error Message Error: Value (<value>) is out of range for Secondary COS value.

The valid range is 0 to 7. Explanation The value of MAC ACL Secondary COS is out of range. Recommended Action The range of MAC ACL Secondary COS is 0 to 7.

Error Message Error: Failed to set Destination MAC and Destination MAC Mask.

Destination MAC is an invalid MAC address. Explanation User try to configure the Destination MAC of a MAC ACL, but the

selected MAC ACL name does not exist. Recommended Action Refresh the WEB page, and select the correct MAC ACL name

again.


Error Message Error: Failed to set Destination MAC and Destination MAC Mask.

Destination MAC Mask is an invalid MAC address. Explanation User try to configure the Destination MAC Mask of a MAC ACL,

but the selected MAC ACL name does not exist. Recommended Action Refresh the WEB page, and select the correct MAC ACL name

again.

Error Message Error: Failed to set Ethertype User Value. Ethertype User Value

is an invalid hex. Explanation User try to configure the Ethertype of a MAC ACL, but the value

is not valid alphanumeric characters. Recommended Action Configure MAC ACL Ethertype with alphanumeric characters

600 to ffff.

Error Message Error: Value (<value>) is out of range for Ethertype User Value.

The valid range is 600 to ffff. Explanation The value of MAC ACL Ethertype is out of range. Recommended Action The range of MAC ACL Ethertype with 600 to ffff.

Error Message Error: Failed to set Source MAC and Source MAC Mask. Source

MAC is an invalid MAC address. Explanation User try to configure the Source MAC of a MAC ACL, but the

selected MAC ACL name does not exist. Recommended Action Refresh the WEB page, and select the correct MAC ACL name

again.

Error Message Error: Failed to set Source MAC and Source MAC Mask. Source

MAC Mask is an invalid MAC address. Explanation User try to configure the Source MAC Mask of a MAC ACL, but

the selected MAC ACL name does not exist. Recommended Action Refresh the WEB page, and select the correct MAC ACL name

again.


is 0 to 4095. Explanation The value of MAC ACL VLAN is out of range. Recommended Action The range of MAC ACL VLAN is 0 to 4095.


This section contains Port Config module messages.

Error Message Error: Value is out of range for Sequence Number. The valid

range is 1 to 4294967295. Explanation The value of ACL Sequence Number is out of range. Recommended Action The range of ACL Sequence Number is 1 to 4294967295.

Error Message No IP ACLs are currently configured. Explanation User try to apply IP ACLs to interfaces, but there are no IP ACLs

configured in the system. Recommended Action To create the IP ACLs first, and then apply it to the interfaces.

Error Message No MAC ACLs are currently configured. Explanation User try to apply the MAC ACLs to interfaces, but there are no

MAC ACLs configured in the system. Recommended Action To create the MAC ACLs first, and then apply it to interfaces.


4.4.7 IP Filter

This section contains IP Filter module messages.

Error Message Error : Invalid Filter Address 1 Explanation User try to configure a IP address in the Filter Address 1, but it is

failed. Recommended Action Use the valid IP address for IP Filter Address 1.









Error Message Error : Invalid Filter Address 6 Explanation User try to configure a IPv6 address in the Filter Address 6, but it

is failed. Recommended Action Use the valid IPv6 address for IP Filter Address 6.



Error Message Error : Invalid Filter Address 8


Explanation User try to configure a IPv6 address in the Filter Address 8, but it is failed.

Recommended Action Use the valid IPv6 address for IP Filter Address 8.



Error Message Error : Invalid Filter Address 10 Explanation User try to configure a IPv6 address in the Filter Address 10, but

it is failed. Recommended Action Use the valid IPv6 address for IP Filter Address 10.


4.4.8 Secure HTTP

This section contains Secure HTTP module messages.

Error Message Error: Failed to set TLS Version 1 Mode and SSL Version 3

Mode. Both these should not be simultaneously disabled. Explanation User try to disable TLS Version 1 and SSL Version 3 at the same

time, but it is failed. Recommended Action TLS Version 1 or SSL Version 3 could not be disabled at the

same time.

Error Message Error: HTTPS Port format is invalid. Explanation User try to configure the HTTPS port with non-numeric

characters. Recommended Action Use numeric characters for HTTPS port.

Error Message Error: Value (<value>) is out of range for HTTPS Port. The valid

range is 1 to 65535. Explanation The value of HTTPS is out of range. Recommended Action The range of HTTPS is 1 to 65535.

Error Message Error: Failed to set port number. Explanation User try to configure the HTTPS port, but the port number is

already configured by other protocol in the system. Recommended Action Use other port number for HTTPS port.

Error Message Error! HTTPS Soft Timeout format is invalid. Explanation User try to configure HTTPS Soft Timeout with non-numeric

characters. Recommended Action Use numberic characters for HTTPS Soft Timeout.

Error Message Error! Value (<value>) is out of range for HTTPS Soft Timeout.

The valid range is 1 to 60. Explanation The value of HTTPS Soft Timeout is out of range. Recommended Action The range fo HTTPS Soft Timeout is 1 to 60.

Error Message Error! HTTPS Hard Timeout format is invalid. Explanation User try to configure HTTPS Hard Timeout with non-numeric

characters. Recommended Action Use numeric characters to configure HTTPS Hard Timeout.


Error Message Error! Value (<value>) is out of range for HTTPS Hard Timeout.

The valid range is 1 to 168. Explanation The value of HTTPS Hard Timeout is out of range. Recommended Action The range of HTTPS Hard Timeout is 1 to 168.

Error Message Error! Maximum Number of HTTPS Sessions format is invalid. Explanation User try to configure Maximum Number of HTTPS Session with

non-numeric characters. Recommended Action Use numeric characters for Maximum Number fo HTTPS

Sessions.

Error Message Error! Value (<value>) is out of range for Maximum Number of

HTTPS Sessions. The valid range is 0 to 16. Explanation The value of HTTPS Sessions is out of range. Recommended Action The range of HTTPS Sessions is 1 to 168.


4.4.9 Secure Shell

This section contains Secure Shell module messages.

Error Message Error: Failed to set Protocol Level. Version 1 or Version 2 must

be enabled. Explanation User try to disable both version 1 and version 2 of SSH protocol

at the same time, but it is failed. Recommended Action SSH version 1 or SSH version 2 must be enabled.

Error Message Error: Failed to set SSH Session idle timeout. Explanation User try to configure SSH Session Timeout with non-numeric

characters or with the value is out of range. Recommended Action Use numeric characters for Set Connection Timeout and the

range of the value is 1 to 160.


4.4.10 Denial-of-Service

This section contains Denial-of-Service module messages.

Error Message Error: Max ICMP Size format is invalid. Explanation User try to configure Max ICMP Size with non-numeric . Recommended Action Use numeric characters for Max ICMP Size.

Error Message Error: Value (<value>) is out of range for Max ICMP Size. The

valid range is 0 to 1023. Explanation The value of Max ICMP Size is out of range. Recommended Action The range of Max ICMP Size is 0 to 1023.

Error Message Error: Max ICMPv6 Size format is invalid. Explanation User try to configure Max ICMPv6 Size with non-numeric

characters. Recommended Action Use numeric characters for Max ICMPv6 Size.

Error Message Error: Value (<value>) is out of range for Max ICMPv6 Size. The

valid range is 0 to 1023. Explanation The value of Max ICMPv6 Size is out of range. Recommended Action The range of Max ICMPv6 Size within 0 to 1023.


4.5 QoS

4.5.1 DiffServ

This section contains Class-map module messages.

Error Message Invaid Committed Rate. No action taken. Explanation User input the non-numeric characters for DiffServ policy

Committed Rate. Recommended Action Set the DiffServ policy Committed Rate with numeric character 1

to 4294967295.

Error Message Error: The Committed Rate is out of range. Explanation The value of DiffServ policy Committed Rate is out of range. Recommended Action Set the DiffServ policy Committed Rate with numeric character 1

to 4294967295.

Error Message Error: Invaid Class Name. Explanation The value of DiffServ Class Name is blank. Recommended Action Set the DiffServ Class Name with alphanumeric character.

Error Message Error: Name must be alpha-numeric. Explanation User try to configure DiffServ Class Name with

non-alphanumeric characters. Recommended Action Use alphanumeric characters for DiffServ Class Name.

Error Message Error: Invaid Class Type. Explanation User try to configure DiffServ Class Type without specifying the

value. Recommended Action Use drag-dwon menu to select a value for DiffServ Class Type.

Error Message Error: This Class already exists. Explanation User try to configure a DiffServ Class, but the Class name is

already used in the system. Recommended Action Use other Class name to create DiffServ Class.

Error Message ERROR: Class Rule Not Created. Explanation User try to add a Match Criteria of the DiffServ Class Rule , but

the Match Criteria has been configured. Recommended Action User can add another Match Criteria for the DiffServ Class Rule.


Error Message No Class Match Criteria selected. Explanation User try to add a Match Criteria of the DiffServ Class Rule , but

does not select any item of the ‘Class Match Selector’ field. Recommended Action User should select a criteria and click ‘Add Match Criteria’

button.

Error Message User Input Error: Invalid IP Address. Explanation User try to configure IP Address of the DiffServ Class Match

Criteria, but the IP Address is out of range. Recommended Action Use the numeric character 1 to 255 in form x.x.x.x to set IP

Address for DiffServ Class Match Criteria.

Error Message User Input Error: Invalid Subnet Mask. Explanation User try to configure IP Subnet Mask of the DiffServ Class Match

Criteria, but the IP Subnet Mask is out of range. Recommended Action Use the numeric character 1 to 255 in form x.x.x.x to set IP

Subnet Mask with contiguous ones and no longer than 30 bits.

Error Message User Input Error: Invalid Layer 4 Port Range. Explanation User try to configure DiffServ Class Match Layer 4 Port with

non-numeric characters or the value is out of range. Recommended Action Use the numeric characters for DiffServ Class Match Layer 4

Port and the range of it is 0 to 65535.

Error Message User Input Error: Invalid MAC Address. Explanation User try to configure MAC Address of the DiffServ Class Match

Criteria, but the MAC Address is out of range. Recommended Action Use the alphanumeric character 00 to FF in form

xx:xx:xx:xx:xx:xx to set MAC Address for DiffServ Class Match Criteria.

Error Message User Input Error: Invalid Mac Address Mask. Explanation User try to configure Mac Address Mask of the DiffServ Class

Match Criteria, but the Mac Address Mask is out of range. Recommended Action Use the alphanumeric character 00 to FF in form

xx:xx:xx:xx:xx:xx to set Mac Address Mask for DiffServ Class Match Criteria.

Error Message Error: Ethertype Value out of range. Explanation The value of DiffServ Class Match Ethertype is out of range. Recommended Action The range of DiffServ Class Match Ethertype is 600 to ffff hex

value.


Error Message User Input Error: IP DSCP value out of range. Explanation The value of DiffServ Class Match IP DSCP is out of range. Recommended Action The range of DiffServ Class Match IP DSCP is 0 to 63.

Error Message User Input Error: IP TOS value out of range. Explanation The value of DiffServ Class Match TOS is out of range. Recommended Action The range of DiffServ Class Match TOS is 00 to ff hex value.

Error Message User Input Error: IP TOS Mask value out of range. Explanation The value of DiffServ Class Match TOS Mask is out of range. Recommended Action The range of DiffServ Class Match TOS Mask is 00 to ff hex

value.

Error Message User Input Error: Invalid Protocol Number. Explanation The value of DiffServ Class Match Protocol Number is out of

range. Recommended Action The range of DiffServ Class Match Protocol Number is 0 to 255.

Error Message User Input Error: VLAN Identifier value out of range. Explanation The value of DiffServ Class Match VLAN ID is out of range. Recommended Action The range of DiffServ Class Match VLAN ID is 0 to 4095.

Error Message Class Match Criteria full. Explanation User try to configure the DiffServ Class Match Criteria, but the

Criteria has reached the maximum. Recommended Action Because the Class Criteria can’t be removed. User should delete

a DiffServ Class setting, and create a new Class Rule. Then add the new Criteria for the DiffServ Class.

Error Message Failed to delete class from policy. Explanation User try to delete a class which is associated with policy, and it is

failed. Recommended Action Remove the associated policy before deleting the class.


This section contains Policy-map module messages.

Error Message Error: Invaid Policy name. Explanation User try to create a policy without the policy name. Recommended Action To create DiffServ Policy with a policy name.

Error Message Error: Name must be alpha-numeric. Explanation User try to configure DiffServ Policy name with

non-alphanumeric characters. Recommended Action Use alphanumeric characters for DiffServ Policy name.

Error Message Error: This DiffServ Policy already exists. Explanation User try to configure a DiffServ Policy, but the policy name is

already used in the system. Recommended Action Use other unused name for DiffServ Policy.

Error Message Error: Failed to delete class from policy. Explanation User try to remove a Class form Member Class List of the Policy,

but the Class does not the last class of the class list. Recommended Action User should remove the Class from the last class of the Member

Class List.

Error Message Invalid value field. No action taken. Explanation User try to configure DiffServ Policy action with non-numeric

characters or is out of range. Recommended Action Use numeric character for the DiffServ Policy action and set the

value with correct range value.

Error Message Could not find a free index in policy attribute table. Explanation User try to set the DiffServ policy attribute, but the Class name is

not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.

Error Message This Diffserv Class is not a member of this policy. Explanation User try to set the DiffServ policy attribute, but the Class name is



Error Message Could not create the policy attribute. Explanation User try to set the DiffServ policy attribute, but the Class name is


Error Message Could not set the queue id. Explanation User try to configure the queue id of Diffserv policy, but the Class

name is not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.

Error Message Could not set the marking COS value. Explanation User try to configure the marking CoS of Diffserv policy, but the

Class name is not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.

Error Message Could not set the marking IP DSCP value. Explanation User try to configure the IP DSCP of Diffserv policy, but the


Error Message Could not set the marking IP Precedence value. Explanation User try to configure the IP Precedence of Diffserv policy, but the


Error Message No more attributes can be specified. Explanation User try to configure the Police Simple attribute of Diffserv

policy, but the Class name is not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.

Error Message Could not set the policing attribute Color Conform Class. Explanation User try to configure the policing attribute Color Conform Class,

but the Class name is not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.

Error Message Could not set the policing conform action value. Explanation User try to configure the policing conform action, but the Class

name is not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.


Error Message Could not set the simple policing committed rate value. Explanation User try to configure the simple policing committed rate, but the


Error Message If Conform Action Selector or Violate Action field selected Mark

Cos, the other field should be Drop. Explanation User try to add a Police Simple Attribute to a DiffServ Policy, and

select the Conform or Violate action with ‘Mark CoS’ , but the other action does not set to ‘Drop’.

Recommended Action Set Conform or Violate action with ‘Mark CoS’ for a DiffServ Policy Attribute, the other action must set to ‘Drop’.

Error Message Could not set the policy attribute type. Explanation User try to configure the policy attribute type, but the Class name

is not associated with the policy. Recommended Action Refresh the WEB page, and select the Class name again.

Error Message Could not set the mirror interface. Explanation User try to configure the mirror interface of the policy attribute,


Error Message Could not set the redirect interface. Explanation User try to configure the redirect interface of the policy attribute,


Error Message Color Aware mode requires the existence of one or more color

classes that are valid for use with this policy instance. Press 'Help' for more details.

Explanation User try to configure the Color Aware attribute of a DiffServ Policy Attribute, but the system can not apply the setting.

Recommended Action 1. Create 2 DiffServ Classes(C1 and C2), and one Class(C2) must contains a single, non-excluded match criterion for one of the following fields ‘CoS’ , ‘IP DSCP’ , ‘IP Precedence’. 2. Create a DiffServ Policy(P1) and add 2 DiffServ Classes to the Member Class List. 3. In the ‘Class Definition’ tab, add a ‘Police Simple’ Attribute with C1 class for P1 policy. Click the ‘Configure Selected Attribute’ button. 4. Change the Color Mode to ‘Color Aware’, and confirm the setting, the Color Aware Mode should be applied successfully.


Error Message Error: Failed to delete policy. Explanation User try to delete a policy which is associated with interfaces, but

it is failed. Recommended Action To remove the association from the interfaces first, and then

delete the policy.


4.5.2 COS Messages


Error Message Error: Interface Shaping Rate format is invalid. Explanation User try to configure Interface Shaping Rate with non-numeric

characters. Recommended Action Use numeric characters for the Interface Shaping Rate.

Error Message Error: Value (<value>) is invalid for Interface Shaping Rate. Valid

range is 0 to 100 in increments of 5. Explanation The value of Interface Shaping Rate is out of range. Recommended Action The range of the Interface Shaping Rate is 0 to 100 in

increments of 5.

Error Message Error: Minimum Bandwidth format is invalid. Explanation User try to configure Minimum Bandwidth with non-numeric

characters. Recommended Action Use numeric characters for Minimum Bandwidth.

Error Message Error: Value (<value>) is invalid for Minimum Bandwidth. Valid

range is 0 to 100 in increments of 5. Explanation The value of Minimum Bandwidth is out of range. Recommended Action The range of the Minimum Bandwidth is 0 to 100 in increments

of 5.


4.6 Stacking

This section contains the Unit Config messages.

Error Message Error: Value <switch#> is out of range for Switch ID. The valid

range is 1 to 8. Explanation The value of Switch ID is not numeric character or out of range 1

to 8. Recommended Action The value of field should be in range 1 to 8.

Error Message Error: Failed to set Priority. Explanation The value of Priority is failed to set.

The swith you set might be not present in the stack. Recommended Action Please check the switch is already in the stack.

You can not set the Priority of the provision switch which is not being in the stack.

Error Message Error: Failed to create Switch ID. Explanation The value of Switch ID is failed to create. The Switch ID might be

already exist. Recommended Action Use a valid or unconfgiured Switch ID for the switch provision

function.

Error Message Stack management move not performed! Explanation The target switch doe not exist or does not be ready for being a

stack master. Recommended Action Check the status of target switch if it is in the “Ready” state.


This section contains the Stack MAC Persistent messages.

Warning Message Stack management move not performed! Explanation The target switch doe not exist or does not be ready for being a

stack master. Recommended Action Check the status of target switch if it is in the “Ready” state.

Error Message Error: Value (<value>) is out of range for Persistent Timer. The

valid range is 0 to 60. Explanation The value of Persistent Timer is out of range. Recommended Action Make sure the value is in the range of 0 to 60.


This section contains the Acchive Copy messages.

Error Message Error: Invalid TFTP/FTP Server IP address ! Explanation The value of FTP/TFTP Server IP address is invalid. Recommended Action Use the valid IP address for FTP/TFTP server.


4.7 End-Host-Mode

This section contains the pin-group messages.

Warning Message Error: Failed to set %s. Pin Group name must contain

alphaNumeric characters only, and can't be empty. Explanation Pin Group name is not valid. It must contain alphaNumeric

characters only, and can't be empty. Recommended Action Use alphanumeric characters for pin-group name.

Warning Message Error: Failed to create Pin Group. Pin Group already exists. Explanation Create a pin-group with the group name is failed due to the

group name has been used. Recommended Action Use another group name to create pin-group.

Warning Message Error: Value (%d) is out of range for Repinning Timer, The valid

range is 10 to 60. Explanation The valid timer vaule is range from 10 to 60 seconds. Recommended Action Enter the valid value.


Documents

PRIMERGY BX900/BX400 Blade Server Systems - Fujitsumanuals.ts.fujitsu.com/file/10227/sb6-sb11a-sb11-smg-en.pdf · PY CB Eth Switch/IBP 1 GB 18/6 ... 4.1.2 System Utilities ... 356