Price quote 1.0 NON-MnDOT PRICE SCHEDULE DUMP BOX

Price quote for:

Vendor Name:Contact Person:Street Address:P.O. Box:

City, State, Zip:Phone #:

Toll Free #:

Fax #:

Email Address:

Item # Information Requested Answer1.0 Box Make and Model Henderson 10’ Mark E-SA 24/32

List Truck Type Box Fits Single axle, 84" useable CA is recommended

Box Style Unibody design, crossmemberless (Western style)

Width & Length of Box 10ft. box with 84" inside width, 96" outside width

Side Panel Description 24" high, fully welded, 10 ga. grade 50 Hi-tensile steel, fully boxed-in & fully welded top rails. Rub rails are sloped for dirt & debris shedding. Includes 2" board pockets front & rear. Single weld-on side

Front Panel Description 52" high, 10ga. grade 50 steel

Floor Description One piece, 3/16" HSLA grade 50 steel floor- 65,000 PSI tensile strength, 4" formed in floor to side radius

Corner Post Description Rear corner post, 7ga. steel, 4-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front

Under Structure Description Two 5" structural steel I-beam long sills, std. skip welded, (with tele hoist) "No splices", crossmemberless- (8" for UB

Tailgate Description 32" high, one piece 10ga. sheet. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. sloped horizontal brace, flush with perimeter boxing (2 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Air trip release kit with double over-center linkage (air over air) (brake chamber type not cylinder

Hinge Description Upper tailgate hinges are 1” thick flame

Galesville, WI 54630608-539-4600

[email protected]

1.0 NON-MnDOT PRICE SCHEDULE DUMP BOX

Universal Truck Equipment Inc.Donnie BjorgeN15921 Schubert Rd.

Description of Peripheral Items (Lights, Access Steps, etc.) LED Stop/turn/tail lights and side clearance lights are mounted in rear corner post. Rubber mounted, shock resistant ICC, 3-light cluster is also included. Front & rear mud flaps included. Pull out type ladder with box step and grab handle, mounted front drivers side on underside of dump body. All electrical wiring connections will be put in heat shrink tubing & will run to a

Is Installation included in price? Yes__X__ or No____Yes, to an acceptable hoist type

Is Box Painted? Yes__X__ or No____Yes, epoxy primed and top coated with an acrylic urathane paint to customers

choice (one standard fleet color), bottom side painted black

Warranty Information One Year Warranty, parts and labor

List Volume Discounts N/A

1.2 Cost for Painting box per spec Included

TOTAL PRICE: $12,273.00

Description AnswerWiring Standoffs Included

Box Options

1.01Air operated tailgate latch, air over air, brake chamber type, in lieu of manual type trip Std.

1.02 Box Vibrator - Make & Model - Cougar model 2700 $620

1.2A Installation of Box Vibrator $541

1.033/16” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” grade 50, 65,000 PSI tensile $588


1.05 38” tailgate in lieu of 32” tailgate (reccomend UB-8-17 or tele hoist) $182

1.0630” sides and 38” tailgate in lieu of 24” sides and 32” tailgate (requires UB-8-17 or tele hoist) $66

1.07 24" 7 ga. sides and ends in lieu of 10 ga. $225

1.08 7 ga. tailgate in lieu of 10 ga. $30

1.09 30" 7 ga. sides & ends in lieu of 10 ga (24" sides) $310

1.10 3/16' AR400 sides & ends in lieu of 10 ga. Grade 50 (24" sides) $1,840

1.11 3/16” AR400 sides & ends in lieu of 10 ga. Grade 50 (30" sides) $2,044

1.12 Mark "E" Asphalt style sloped rear & tailgate $166

1.13One piece sloping sides (includes top rail & bottom rub rail…smooth sides) 10 ga. carbon steel- in lieu of std. $830

1.14One piece sloping sides (includes top rail & bottom rub rail…smooth sides) 7 ga. carbon steel- in lieu of std. $1,123

1.15One piece sloping sides (includes top rail & bottom rub rail…smooth sides) 3/16" AR400 steel- in lieu of std. $1,407

1.16201 stainless steel front & rear corner post, all side bracing, tailgate bracing, and apron in lieu of standard $1,176

1.17 201 stainless steel rear corner post & apron only, in lieu of std. $570

1.18 201 stainless steel rear corner post only, in lieu of std. $336

1.19 3 panel tailgate in lieu of 2 panel $51


1.21 Extra tailgate bracing in 201SS in lieu of std. (3 or 6 panel) $205

1.22 3/4" rebar down both sides for walk/tarp rail $148

1.23 1-1/2", grip strut down both sides for walk rail $163

1.241.24 - 10-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 10' body (note: can also use UB-8-17 hoist with 8" I-beams or 8-21 hoist with 10" I-beams) $310

1.251.25 - Elliptical body sides in lieu of square body sides (add 30" sides & 3/16" AR400 sides & ends) (deduct) ($403)

Cost per loaded mile for pickup and or delivery of vehicle (if applicable): $4.00 Delivery Starting Point City, State, & Zip: N15921 Schubert Rd., Galesville, WI 54630Body Shop Rate $95 Mechanic Shop Rate $95

Price quote for:



Toll Free #:

Fax #:

Email Address:





Side Panel Description 24" high, fully welded, 10 ga. grade 50 Hi-tensile steel, fully boxed-in & fully welded top rails. Rub rails are sloped for dirt & debris shedding. Includes 2" board pockets front & rear. Single weld-on side brace.

Front Panel Description 52" high, 10ga. grade 50 steel construction

Floor Description One piece, 3/16" HSLA grade 50 steel floor- 65,000 PSI tensile strength, 4" formed in floor to side

Corner Post Description Rear corner post, 7 ga. steel, 5-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post

Under Structure Description Two 5" structural steel I-beam long sills, std. skip welded, (with tele hoist) "No splices", crossmemberless- (8" for UB hoist),

608-539-4600

[email protected]



Galesville, WI 54630

Tailgate Description 32" high, one piece 10 ga. sheet. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. sloped horizontal brace, flush with perimeter boxing (2 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Air trip release kit with double over-center linkage (air over air) (brake chamber type not cylinder

Hinge Description Upper tailgate hinges are 1” thick flame cut

Description of Peripheral Items (Lights, Access Steps, etc.) LED Stop/turn/tail lights and side clearance lights are mounted in rear corner post. Rubber mounted, shock resistant ICC, 3-light cluster is also included. Front & rear mud flaps included. Pull out type ladder with box step and grab handle, mounted front drivers side on underside of dump body. All electrical wiring connections will be put in heat shrink tubing & will run to a sealed junction


Is Box Painted? Yes__X__ or No____Yes, epoxy primed and top coated

with an acrylic urathane paint to customers choice (one standard fleet

color), bottom side painted black




TOTAL PRICE: $12,950


Box Options





1.041/4" AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” grade 50, 65,000 PSI tensile $1,103

1.0538” tailgate in lieu of 32” tailgate (requires UB-8-21 or tele hoist) $182





1.103/16' AR400 sides & ends in lieu of 10 ga. Grade 50 (24" sides) $1,993

1.113/16” AR400 sides & ends in lieu of 10 ga. Grade 50 (30" sides) $2,224


1.13

One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 10 ga. carbon steel- in lieu of std. $902

1.14

One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 7 ga. carbon steel- in lieu of std. $1,224

1.15

One piece sloping sides (includes 1 top rail, 1 intermediate side braces, and 1 bottom rub rail)- 3/16" AR400 steel- in lieu of std. $1,545


1.17201 stainless steel rear corner post & apron only, in lieu of std. $570




1.21 Extra tailgate bracing in 201SS in lieu of std. (3 or 6 $205

1.22 3/4" rebar down both sides for walk/tarp rail $163

1.23 1-1/2", grip strut down both sides for walk rail $194

1.24

11-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 11' body (note: can also use UB-8-21 hoist with 10" I-beams) $310

1.25Elliptical body sides in lieu of square body sides (add 30" sides & 3/16" AR400 sides & ends) (deduct) ($403)


Price quote for:



Toll Free #:

Fax #:

Email Address:





Side Panel Description 24" high, fully welded, 10 ga. grade 50 Hi-tensile steel, fully boxed-in & fully welded top rails. Rub rails are sloped for dirt & debris shedding. Includes 2" board pockets front & rear. Single weld-on side brace.

Front Panel Description 52" high, 10ga. grade 50 steel construction

Floor Description One piece, 3/16" HSLA grade 50 steel floor-65,000 PSI tensile strength, 4" formed in floor to side


Under Structure Description Two 5" structural steel I-beam long sills, std. skip welded, (with tele hoist) "No splices", crossmemberless- (8" for UB hoist),

608-539-4600

[email protected]
















Box Options





1.041/4” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” grade 50, 65,000 PSI tensile $1,208






1.10 3/16' AR400 sides & ends in lieu of 10 ga. Grade 50 (24" sides) $2,038

1.11 3/16” AR400 sides & ends in lieu of 10 ga. Grade 50 (30" sides) $2,286


1.13One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 10 ga. carbon steel- in lieu of std. $960

1.14One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 7 ga. carbon steel- in lieu of std. $1,281

1.15One piece sloping sides (includes 1 top rail, 1 intermediate side braces, and 1 bottom rub rail)- 3/16" AR400 steel- in lieu of std. $1,693







1.22 3/4" rebar down both sides for walk/tarp rail (MS) $177

1.23 1-1/2", grip strut down both sides for walk rail (M/S) $213

1.24 Flush sides and tailgate (No Charge) $0



Price quote for:



Toll Free #:

Fax #:

Email Address:

Item # Information Requested Answer1.0 Box Make and Model Henderson 10’ Mark E-SA-SS 24/32,

201 Stainless Steel


Box Style Unibody design, crossmemberless (Western style) 201 stainless steel sides, headsheet, tailgate and all perimeter bracing, front & rear corner posts & rear apron


Side Panel Description 24" high, fully welded, 10 ga. stainless steel, fully boxed-in & fully welded top rails. Rub rails are sloped for dirt & debris shedding. Includes 2" board pockets front & rear.

Front Panel Description 52" high, 10ga. 201 stainless steel construction

Floor Description One piece, 3/16" AR400 steel floor-200,000 PSI tensile strength, 4" floor to side radius

Corner Post Description Rear corner post, 7 ga. 201 S/S, 4-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post

Under Structure Description Two 5" structural steel I-beam long sills (with tele hoist) "No splices", crossmemberless- (8" for UB hoist)

608-539-4600

[email protected]




Tailgate Description 32" high, one piece 10ga. 201 S/S sheet. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. 201 S/S sloped horizontal brace, flush with perimeter boxing (2 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Air trip release kit with double over-center linkage (air over air) (brake chamber type not cylinder




Is Box Painted? Yes____ or No__X__Unpainted dump body- left in it's

natural state. Bottom side & truck frame painted black






Box Options




1.03 1/4” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” AR400 $328



1.06 7 ga. 201 S/S sides and header in lieu of 10 ga. 201S/S (24" sides) $1,045

1.077 ga. 201 S/S sides and header in lieu of 10 ga. 201S/S (30" sides) (must add 30" sides option- 1.5) $1,139

1.08 7 ga. 201 S/S tailgate in lieu of 10 ga. 201 S/S $282

1.09 3 panel S/S tailgate in lieu of 2 panel S/S $172


1.11 3/4" 201 S/S round stock down both sides for tarp rail $239

1.12 1-1/2", 201 S/S grip strut down both sides for walk rail $311

1.13One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 10 ga. 201 stainless steel $1,257

1.14One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 7 ga. 201 stainless steel- in lieu of std. $1,531

1.15

(note: can also use UB-8-17 hoist with 8" I-beams or 8-21 hoist with 10" I-beams) $444

1.16Elliptical body sides in lieu of square body sides (add 30" sides & 7ga. sides & ends) (deduct) ($440)


Price quote for:



Toll Free #:

Fax #:

Email Address:


201 Stainless Steel









608-539-4600

[email protected]















Box Options
















1.1511-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 11' body (note: can also use UB-8-21 hoist with 10" I-beams) $444



Price quote for:



Toll Free #:

Fax #:

Email Address:


201 Stainless Steel









608-539-4600

[email protected]















Box Options


















Price quote for:



Toll Free #:

Fax #:

Email Address:

Item # Information Requested Answer1.0 Box Make and Model Henderson Mark E-ti (XD) 36/44 (13’-

16’)

List Truck Type Box Fits Tandem axle only


Width & Length of Box 13' box length & 96" outside width, 84" inside width

Side Panel Description 36" high, fully welded, 10 ga. grade 50 Hi-tensile steel, fully boxed-in & fully welded top rails, rub rails are sloped for dirt & debris shedding. Includes 2" sideboard pockets

Front Panel Description 60" high, 10 ga. construction. Boxed top rail, 12" internal doghouse

Floor Description One piece, 3/16" AR400 steel floor-200,000 PSI tensile strength, 45 degree floor to side knee-brace formed into floor


Under Structure Description Two 8" structural steel I-beam long sills with "No splices" (8" x 13.0 lbs./ft.), std. skip welded,

608-539-4600

[email protected]





Hinge Description Flush mount 1/2" flame-cut pivots. Heavy-duty 1" flame cut hinge plates.











Box Options




1.03 Mark E Asphalt body style (includes sloped tailgate) $166

1.04 13-1/2’ or 14’ dump body in lieu of 13’ $253


1.06 15-1/2' and 16’ dump body in lieu of 13’ $697

1.0744” sides and 52” tailgate in lieu of 36” sides & 44” tailgate (13' and 14' bodies) $209


1.091/4” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” AR400 floor (13' body) $494




1.13 7 ga. sides and ends in lieu of 10 ga. (13' body with 36" sides) $324








1.21 3/16” AR400 sides & ends in lieu of 10 ga. (13' body with 36" sides) $2,548








1.29One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 10 ga. carbon steel- in lieu of std. 10 ga. straight sides (per foot - times foot length of body) $85

1.30One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 7 ga. carbon steel- in lieu of 7 ga. straight sides (per foot - times foot length of body) $117

1.31One piece sloping sides (includes 1 top rail, 1 intermediate side braces, and 1 bottom rub rail)- 3/16" AR400 steel- in lieu of 3/16" AR400 straight sides (per foot - times foot length of body) $148

1.32

bodies) $570

1.33201 stainless steel front & rear corner post, all side bracing, tailgate bracing, and apron in lieu of standard (13' bodies) $1,528




1.37 4 panel tailgate in lieu of 3 panel (44” & 52 tailgate) $65



1.403/4" rebar down both sides for walk/tarp rail (all bodies) (per foot - times foot length of body) $15

1.411-1/2", grip strut down both sides for walk rail (all bodies) (per foot - times foot length of body) $18



Price quote for:



Toll Free #:

Fax #:

Email Address:

Item # Information Requested Answer1.0 Box Make and Model Henderson Mark E-ti (XD-SS) 36/44

(13’-16’), 201 Stainless Steel

List Truck Type Box Fits Tandem axle only


Width & Length of Box 13' box length & 96" outside width, 84" inside width

Side Panel Description 36" high, fully welded, 10 ga. 201 stainless steel, fully boxed-in & fully welded top rails, rub rails are sloped for dirt & debris shedding. Includes 2" sideboard pockets

Front Panel Description 60" high, 10 ga. 201S/S construction. Boxed top rail, 12" internal doghouse

Floor Description One piece, 3/16" AR400 steel floor-200,000 PSI tensile strength, 45 degree floor to side knee-brace formed into floor

Corner Post Description Rear corner post, 7 ga. stainless steel, 5-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post

Under Structure Description Two 8" structural steel I-beam long sills with "No splices" (8" x 13.0 lbs./ft.), std. skip welded,

608-539-4600

[email protected]




Tailgate Description 44" high, one piece 10 ga. 201S/S sheet. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. S/S sloped horizontal brace, flush with perimeter boxing (3 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Air trip release kit with double over-center linkage (air over air) (brake chamber type not cylinder operated)

Hinge Description Flush mount 1/2" flame-cut pivots. Heavy-duty 1" flame cut hinge plates.










Box Options




1.03 Mark E Asphalt body style (includes sloped tailgate) $166



1.06 15-1/2' and 16’ dump body in lieu of 13’ $1,143







1.13 7 ga. sides and ends in lieu of 10 ga. (13' body with 36" sides) $1,424








1.21

One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 10 ga. 201 stainless steel- in lieu of std. 10 ga. straight sides (per foot - times foot length of body) $128

1.22

One piece sloping sides (includes 1 top rail, 2 intermediate side braces, and 1 bottom rub rail)- 7 ga. 201 stainless steel- in lieu of std. 7 ga. straight sides (per foot - times foot length of body) $176



1.253/4" 201 S/S round stock down both sides for tarp rail (per foot - times foot length of body) $24

1.261-1/2", 201 S/S grip strut down both sides for walk rail (per foot - times foot length of body) $31



Price quote for:



Toll Free #:

Fax #:

Email Address:

Item # Information Requested Answer1.0 Box Make and Model Henderson 10' MuniBody 2


Box Style Crossmemberless body with live bottom floor

Width & Length of Box 10ft. box length & 96" outside width

Side Panel Description 36" high, fully welded, 7ga. grade 50 Hi-tensile steel, fully boxed-in & fully welded top rails, rub rails are sloped for dirt & debris shedding 22 degree floor to side slope.

Front Panel Description 60" high, 7ga. construction. Boxed top rail and 4" sideboard pockets.

Floor Description 1/4" AR400 steel conveyor floor with 28" wide pintle chain - 8 tooth sprockets with 2" drive & idler shafts 25:1 planetary gear drive motor- rear mounted 15" rear spreader apron. Rear Std. steel spinner diskdischarge spinner assy.

Corner Post Description Rear corner post, 7 ga. steel, 5" x 12-3/4" full depth tied to 12" deep structural steel rear apron with 1/4" tailgate latch reinforcement plates

Under Structure Description Stainless Steel formed long sills (inner & outer)

608-539-4600

[email protected]




Tailgate Description One piece 7ga. Grade 50 steel. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. sloped horizontal brace, flush with perimeter boxing Screw 1-1/4" upper & lower pins. Air trip release kitadjustable rear feedgate door. with double over-center linkage (air over air) (Dual brake chamber type not cylinder












Box Options




1.03

tailgate) $350

1.04

tailgate) $484

1.05 3/16” AR400 sides & ends in lieu of 7ga. Grade 50 steel $2,438

1.0636" Unpainted 201 SS Sides & Ends with 1/4" AR400 floor in lieu of grade 50 painted $6,174



1.09 Standard Duty Top Grate Screens (3/8" rod x 3/8" rod)- installed $1,651

1.1 Heavy Duty Top Grate Screens (3/8" rod thru 2" flat)- installed $2,176

1.11 Rubber belt over pintle chain in lieu of std. pintle chain $1,552

1.12Double conveyor cross bars in lieu of std. pintle chain (bars every other link) $658

1.13 3/16" AR400 steel conveyor cover plate $659

1.14 Sloped steel side boards- installed and fully welded- Mild Steel $966

1.15 Sloped steel side boards- installed and fully welded- Stainless Steel $1,752

1.16 Dual Auger Option in lieu of std. pintle chain…includes top screens $4,359

1.17201 stainless steel rear corner post, all side bracing, tailgate bracing, fenders, and apron in lieu of standard $1,568


1.19 Underbody Pans (Stainless Steel)- installed $472


Price quote for:



Toll Free #:

Fax #:

Email Address:










608-539-4600

[email protected]


















1.03

tailgate) $350

1.04

tailgate) $484










1.14 Sloped steel side boards- installed and fully welded- Mild Steel $1,007







Price quote for:



Toll Free #:

Fax #:

Email Address:










608-539-4600

[email protected]
















Box Options




1.03

tailgate) $364

1.04

tailgate) $510

















Price quote for:



Toll Free #:

Fax #:

Email Address:










608-539-4600

[email protected]
















Box Options




1.03

tailgate) $370

1.04

tailgate) $526

















Price quote for:



Toll Free #:

Fax #:

Email Address:


List Truck Type Box Fits Tandem axle, 120" useable CT is recommended








608-539-4600

[email protected]
















Box Options




1.03

tailgate) $377

1.04

tailgate) $539








1.12

link) $940









Price quote for:



Toll Free #:

Fax #:

Email Address:










608-539-4600

[email protected]
















Box Options




1.03 42" Sides & Ends - 7ga. Grade 50 steel (in lieu of 36" sides & 48" tailgate) $384

1.04 48" Sides & Ends - 7ga. Grade 50 steel (in lieu of 36" sides & 48" tailgate) $553








1.12

link) $1,017









Price quote for:



Toll Free #:

Fax #:

Email Address:










608-539-4600

[email protected]
















Box Options




1.03

tailgate) $391

1.04

tailgate) $566





1.09Double conveyor cross bars in lieu of std. pintle chain (bars every other link) $1,093




1.13 Dual Auger Option in lieu of std. pintle chain…includes top screens $0





Price quote for:



Toll Free #:

Fax #:

Email Address:










608-539-4600

[email protected]
















Box Options




1.0342" Sides & Ends - 7ga. Grade 50 steel (in lieu of 36" sides & 48" tailgate) $398

1.0448" Sides & Ends - 7ga. Grade 50 steel (in lieu of 36" sides & 48" tailgate) $578








MuniBody Options

1.200 Poly Spinner Disk in lieu of std. $145

1.205 Stainless steel ladder in lieu of mild steel $159

1.210 Conveyor oiling system- installed $201

1.215Front Cross Conveyor (and rear discharge) (9'-12' bodies) SA pin to pin cylinder (installed) $2,417

1.220Front Cross Conveyor (and rear discharge) (13'-16' bodies) SA pin to pin cylinder (Installed) $4,540

1.225 Front Center and rear discharge (9'-12' bodies) $684

1.230 Front Center and rear discharge (13'-17' bodies) $2,807

1.235 External doghouse in lieu of std. $245

1.240 Rear asphalt patch pan with chute & mount (Front/Rear Discharge) $822

1.245 Rear asphalt patch pan (Rear Discharge Only) $522

1.250 Rear Spinner Assy with chute & mount (front/rear discharge) $1,738

1.255Combination Rear Spinner Assy & asphalt patch pan with chute & mount (front/rear discharge) $1,148

1.260 Front right hand berm chute (M/S) $543

1.265 Rear berm chute (M/S) $714

1.270 (1) Mild Steel Toolbox (either side)- Fender mounted (9'-12' body) $795

1.275 (1) Mild Steel Toolbox (either side)- Fender mounted (13'-16' body) $890

1.280 (2) Mild Steel Toolboxes (one on each side)- Fender mounted (9'-12' body) $1,591

1.285 (2) Mild Steel Toolboxes (one on each side)- Fender mounted (13'-16' body) $1,781

1.290 (1) Stainless Steel Toolbox (either side)- Fender mounted (9'-12' body) $1,050

1.295 (1) Stainless Steel Toolbox (either side)- Fender mounted (13'-16' body) $1,324

1.300

body) $2,119

1.305

body) $2,647

1.310 (1) 75 Gallon Poly Prewet Tank (either side)- Fender mounted $655

1.315 (2) 75 Gallon Poly Prewet Tank (one on each side)- Fender mounted $1,308

1.320 (1) 105 Gallon Poly Prewet Tank (either side)- Fender mounted $1,152








1.360 (1) 230 Gallon Poly Prewet Tank (either side)- Fender mounted (NA - 10'-12') $1,832


1.370 Cradle mount oil tank in lieu of truck frame mounted $244

1.375 Cradle mount valve body enclosure in lieu of truck frame mounted $380

1.380 Install cover above rear feed gate door $423

1.385Dual air cylinder operated rear feed gate door with in cab control installed (std. screw jack is still used with air cylinder set-up) $1,364

1.390 Rear conveyor control (on/off)- electric switch type- installed $247

Cost per loaded mile for pickup and or delivery of vehicle (if applicable): $4.00 Delivery Starting Point City, State, & Zip:

WI 54630

Body Shop Rate $95 Mechanic Shop Rate $95

Price quote for:



Toll Free #:

Fax #:

Email Address:

Item # Information Requested AnswerDump Body Options (All Bodies)

1.300 One set of M/S shovel hooks, fork type (each) $89

1.305 One set of S/S shovel hooks, fork type (each) $100

1.310 22” x 78” cabshield, installed and fully welded, 10 ga. mild steel $810

1.315 22” x 78” stationary cabshield, w/rubber flap, installed, 10 ga. m/s $2,248

1.320 409 stainless steel cabshield in lieu of mild steel $1,491

1.325 22” x 78” cabshield, installed and fully welded, 10ga. 201S/S $976

1.330 22” x 78” stationary cabshield, w/rubber flap, installed, 10ga. 201 S/S $2,248

1.335 7 ga. grade 50 steel cabshield in lieu of 10 ga. grade 50 steel $75

1.340 7 ga. 201 S/S cabshield in lieu of 10 ga. S/S $198

1.345 Poly Fenders with rear flaps in lieu of two sets of std. mud flaps (single axle) $800

1.350 Poly Fenders with rear flaps in lieu of two sets of std. mud flaps (tandem axle) $1,446

1.355 Tailgate grab handles, one in each corner of lower panel - M/S $78

1.360 Tailgate grab handles, one in each corner of lower panel - S/S $88

1.365 Fold-up type ladder in lieu of std. stow-away type ladder $95

1.370 Stainless Steel fold-up type ladder in lieu of std. stow-away type ladder $210

1.375Factory installed tool box across front of dump body, 1/4” grade 50 shell, weather tight sealed key locking doors, one on each side $1,606

1.380Factory installed tool box across front of dump body, 3/16” AR400 shell, weather tight sealed key locking doors, one on each side $1,710

1.385Factory installed tool box across front of dump body, 1/4” S/S shell, weather tight sealed key locking doors, one on each side $1,775

1.390 Aluminum tool box frame mounted w/ brackets, 18” x 18” x 24” $730

608-539-4600

[email protected]






1.405Donovan, electric tarp system with asphalt tarp, all aluminum arms, and tarp housing, standard install, off top of front header $2,615

1.410 Donovan front tension bows- installed $645

1.415Set of LED Snow Plowing Lights with Heated Lens Truck Lite model 80990 7in round- 23 Doide- Polycarbonate- 12-24V- std. 94in harness, standard install, off cowling of truck hood with custom made S/S mounting brackets and on/off switch in cab $1,315

1.420

standard install, off cowling of truck hood with custom made S/S mounting brackets and on/off switch in cab $1,135

1.425

bulb, standard install, off cowling of truck hood with custom made S/S mounting brackets and on/off switch in cab $840

1.430 Work light, sealed beam type, installed (i.e. sander or wing etc.) (each) $100

1.435 Work light, LED Type, installed (i.e. sander or wing etc.) (each) $132

1.440Two (2) oval rear LED warning lights, recessed rubber mounted in rear corner post, Whelen 5G series, 14 different flash patterns, installed with on/off switch in cab $412

1.445Two (2) oval rear LED warning lights, recessed rubber mounted in rear corner post, Whelen TIR6 series, 14 different flash patterns, installed with on/off switch in cab $499

1.450Whelen Strobe, self contained, 16 jule, class 1, cabshield mounted with protective guard, wiring will run to on/off switch in cab (each) $0

1.455Whelen model L21HAP - SUPER-LED Beacon, Amber, 6 in. dome type, class 1, polycarbonate base and dome, cabshield mounted with protective guard, wiring will run in conduit to on/off switch in cab (each) $385

1.460Whelen DOT3-401D, Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror mouted fornt strobes and rear light housing welded to outside of rear corner post $4,091

1.465Whelen DOT3-401D (ADD4TIR3), Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads & Stainless Steel housing w/ TIR3 side light, standard install, mirror mounted front strobes and rear light housing welded to outside of rear corner post $4,318

1.470Whelen DOT3-701D, Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 700 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror mouted front strobes and rear light housing welded to outside of rear corner post $4,034

1.475Whelen DOT3-701D (ADD7TIR3), Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 700 series "D" light heads & Stainless Steel housing w/ TIR3 side light, standard install, mirror mounted front strobes and rear light housing welded to outside of rear corner post $4,261

1.480Adjustable aluminum light bar, cab mounted, in lieu of mirror mount brackets, (truck cab needs to have a drip rail/rain gutter) $315

1.485Adjustable aluminum light bar, cab mounted, in lieu of mirror mount brkt. (truck has "no" drip rail/rain gutter - holes will need to be drilled in truck cab) $401

1.490 Weld rear DOT3 lighthead housings in rear corner post in lieu of welding to outside of rear corner post $85

1.495Federal Signal model 454205-25 Economy HighLighter LED warning light Class 1, 15" mini-lightbar with Amber LED's and Clear Lens- cabshield mounted with protective guard, wiring will run to on/off switch in cab (each) $520

1.500Federal Signal model 454201-25 HighLighter LED warning light, Class 1, 15" mini-lightbar with Amber LED's and Clear Lens- cabshield mounted with protective guard, wiring will run to on/off switch in cab (each) $590

1.505 Electronic Back-up Alarm- 97 decibels- 12 volt systems- installed $108

1.510Switch panel box with 5 or 6 lighted switches and individual breakers for each switch, installed with one piece full wiring harness from switch box to light, price is in lieu of dash mounted switches $415

1.515 Quick detachable mud flaps in lieu of standard (per set) $109

1.520Roll-Rite, electric tarp system with asphalt tarp, all aluminum arms, tarp housing, and TarpMaster Motor - standard install, off top of front header $3,055

1.525 Roll-Rite Super Duty motor in lieu of TarpMaster Motor $200

1.530 Roll-Rite front tension bows- installed $531

1.535Aero, electric tarp system with asphalt tarp, all aluminum arms, tarp housing, and Power Plus Motor - standard install, off top of front header $2,965

1.540 Aero front tension bows- installed $463

1.545 Henderson (1) 60 gallon elliptical pre-wet tank - installed $1,106

1.550 Henderson (2) 60 gallon elliptical pre-wet tanks - installed $2,213

1.555 Henderson (1) 100 gallon elliptical pre-wet tank - installed $1,241

1.560 Henderson (2) 100 gallon elliptical pre-wet tanks - installed $2,483

1.565 Henderson Stainless Steel pre-wet tank receiver tubes (elliptical bodies) (Ea.) $99

1.570 Nordic N400 HID auxillary lights (994-225U)- lightbar or stationary cabshield mounted $798

1.575 Amber wing warning light Whelen TIR3 # WPLOW1A- "In Use" - installed $295

1.580 Amber wing warning light Whelen TIR3 # WPLOW2A- "Stowed" - installed $295

1.585 Hoist stabilizer (used with Mailhot tele hoist)- installed $3,182

1.590 Stainless Steel rear chute tube brackets & S/S storage pins ilo M/S - installed $395

1.595 License plate light- std. install $207

1.600 Body-Up Switch- installed $122

1.605 Rubber/Steel mounting pads- installed (all MKE bodies 13'-16') $980

1.610 20 ton pintle hitch installed w/ 3/4” steel plate bracing, D-rings, plug $857

1.615 30 ton pintle hitch installed w/ 3/4” steel plate bracing, D-rings, plug $914

1.620 45 ton pintle hitch installed w/ 1” steel plate bracing, D-rings, plug $1,040

1.625 50 ton pintle hitch installed w/ 1” steel plate bracing, D-rings, plug $1,063

1.630 Custom chipper hitch- installed by itself (with no other hitch) $470

1.635 Custom chipper hitch- installed with additional hitch (must add additional hitch) $545

1.640 Whelen SnowAway (H400SD) 400 series heated rear lens with auto on/off & switch in the cab $1,735

1.645 Stainless Steel fixed length cabshield mounted lightbar in lieu of mirror mount brkts $180

1.650Whelen DOT3-410D, Two Stainless Steel 2-lamp Micro 400 LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror mouted fornt strobes and rear light housing welded to outside of rear corner post $4,138

1.655Whelen DOT3-410D, (ADD4TIR3), Two Stainless Steel 2-lamp Micro 400 LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror mouted fornt strobes and rear light housing welded to outside of rear corner post $4,359

1.660 Donvan Spring Trap (spring loaded tarp hold down)- installed $480

1.665 S/S unpainted stow-away ladder in lieu of std. M/S painted stow-away ladder $120

1.670 Greaseable upper tailgate pins (all bodies) $27

1.675 Amber wing warning light Whelen TIR3 on UTE SS bracket- "In Use" - installed $240

1.680 Fully welded I-beam longsills (MKE Bodies) in lieu of std. skip welded $132

1.685 (1) extra obround light hole in each rear corner post $25

1.690 (2) extra obround light holes in each rear corner post $50

1.695 Larger 8.0 cu. in. conveyor drive motors in lieu of std. $80

1.700 Oval LED Back-Up Lights - installed $180

1.705 3-oval hole Stainless Steel light boxes - installed to outside rear corner posts with 1/2" gap $330

1.710 (4) single oval hole Stainless Steel light boxes - installed on cabshield with 4-LED S/T/T $670

1.715 Install one set of chain hangers (in requested location) (per set) $160

1.720 Stainless Steel Tubing front to rear on MuniBody's $455

1.725 Install inside step $80

1.730 Relocate factory truck tow hooks $128

1.735 Weld stainless steel angle to tailgate for customer to install license plate $80

1.740 Install custom round storage basket to truck frame $360

1.745 Install reflective 3M tape to sides & ends of body…get location details (per feet of tape needed) $2

1.750 Whelen NP6BB Work light, LED type, installed (i.e. sander or wing ect. (each) $205

1.755 Air Compensated Pintle hitch - Installed (must add a pintle hitch) $175

1.760 Wing Laser Guide Kit - GL3000PMC - installed on passenger side mirror $3,324

1.765 Electric Brake Controller (1-4 axels), Installed $480

1.770 Back-Up Camera System with monitor & heated camera - std. install $799

1.775 Additional heated camera for wing veiwing - std. install (2nd camera) $310

1.780 Heated camera system only (no monitor…plugs in FA 6100 display screen) $660

1.785 Stainless Steel branch guards for front Whelen DOT lights - installed (each) $155

1.790 Relocate factory transmission control pad (as far as factory harness will allow) $135

1.795Set of 2…ABL LED Work Lights, 3,000 Lumen, 5in x 5in (Long Range)mounted on existing aluminum light bar assembly (3001-0016) $665

1.800Custom Stainless Steel Fenders installed on elliptical tub bodies- use existing prewet tank brackets (Single Axle) $2,060

1.805Custom Stainless Steel Fenders installed on elliptical tub bodies- use existing prewet tank brackets (Tandem Axle) $2,555

1.810 Donovan Tarp Roller & Hold Down Kit (2-roller bars & Stainless Steel brackets)- Installed $540

1.815 High Lift Tailgate with air over air in cab control, installed $2,490

1.820 Composite Side Boards- Black- Installed with one center brace on each side (10'-12' bodies) $725

1.825 Composite Side Boards- Black- Installed with two center braces on each side (13'-15' bodies) $825

1.830 Composite Side Boards- Black- Installed with two center braces on each side (16'-17' bodies) $925

Cost per loaded mile for pickup and or delivery of vehicle (if applicable): $4.00

Delivery Starting Point City, State, & Zip:

N15921 Schubert

Rd., Galesville, WI 54630

Body Shop Rate $95 Mechanic Shop Rate $95

Documents

Price quote 1.0 NON-MnDOT PRICE SCHEDULE DUMP BOX