Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Prestige 3D
Prestige 3D is the new three compartment dado trunking system from MK that satisfies the need for
compliance with the Cat 6 structured cabling standard and the desire for easier and faster installation.
Prestige 3D meets both these demands, while maintaining the stylish high aesthetics of Prestige Plus™
and Compact™.
Features
l Greater trunking depth to cater for Cat 6 structured cabling systems, supports 45mm deep back boxes
l Fast installation, approximately 30% time saving* compared to Prestige Plus™
l Cat 6 compliant Data Sweep™, with no loss of capacity and without the need for bulky or bulbous external corners
l Flexible Internal and External Corners compensate for poor building tolerances
l Divider Knockouts combined with open back boxes, making wiring easier and faster with no drilling or cutting
l Two stage Hinge Lids enable cables to be supported by trunking cover during installation, and makes retro-installation of additional cables simpler
l Cat 6 compliant moulded Flat Angles, Tees and Internal/External Corners
* Based on internal installation trials of a typical small office configuration of approximately 15m2
Prestige 3D Features
SCREW FIxING KITWhere higher security is required, all fitting covers can be
secured using the Screw Fixing Kit. The Screw Fixing Kit
is self-locating and self-drilling on the styling line of the
system and has cover to hide the screw head.
PRE-PuNCHED bASESWall fixing is simplified
by the inclusion of pre-
punched oval holes at
110mm intervals, ensures
no drilling is required.
FLAT TEES AND ANGLESThe ingenuity of the tee design allows a variety of cable drop
permutations. The tee’s bridge can be fitted in two positions
increasing the versatility of cable runs whilst maintaining the
correct separation and Cat 6 compliance. Screw fixing hole
locations have a protective shroud to prevent the chafing
of cables. Both the Flat Angle and Tee compartment divider
walls are curved (Cat 6 compliant) to allow data cables to
lay in with no loss of capacity. The covers are one piece and
clip securely into place, and the base is also a single moulded
item, giving more strength than fabrication. Couplers are
not required where the tee/angle meets the trunking as the
moulded covers now overlap the junction.
ExTERNAL CORNERExternal Corners accommodate +/- 5
degree irregularities in the squareness
of a corner. Corners come ready
assembled to click into place, and offset
side split can be hidden on a non-
prominent face to maximise aesthetics.
DATA SWEEP™The unique patented Data Sweep™
provides Cat 6 data cabling
compliance, with no loss of capacity
and without the need for bulky,
protruding corner covers.
STyLING LINESAll fittings are moulded
with styling lines for
aesthetic continuity.
END CAPSNeatly finish runs of
trunking, (moulding
provides internal location
for extra security from
optional screw fixing).
DIvIDER
KNOCKOuTSWiring is also made
easy with 50 x 21mm
knockouts at 110mm
intervals along
compartment dividers,
providing instant access
to open back boxes, with
no drilling or cutting.
bACK bOxES1 gang, 2 gang and 3 gang ‘open box’ 45mm deep back boxes
allowing ease of connection to power and data devices. The open
top/bottom allows unhindered tool free cable entry, through the
trunking compartment divider knockout. The back box can slide
to align with appropriate knockout.
ELECTROMAGNETIC INTERFERENCEAdditional data cable/signal protection is
provided by fitting screening divider VP30.
TRuNKING HINGE LIDSA two stage location gives a
hinge effect, enabling cables
to be supported by the
trunking cover during the
installation, thereby reducing
the need for cable retainers.
Cover design avoids dust
traps and makes cleaning
easier, and continues the
aesthetics of the trunking.
PROFILE170 x 57mm profile to suit
most installation needs.
Available in white, charcoal
and choice of RAL colours.
INTERNAL CORNERDesigned to accommodate
irregularities in the squareness
of the corner with a +/- 5
degrees flexibility range. The
centre split gives maximum
adjustment. Covers are radiused
and compatible with Cat 6 data
cabling requirements.
CONDuIT ADAPTORSingle adaptor for conduit and
mini-trunking (20 and 25mm
conduit YT2 and YT4 mini
trunking). Supplied with bridge.
Prestige 3D Selector / Capacities
Main Carrier – vP180
Curved Cover – vP110
Curved Cover – vP110
Straight Cover – vP100
Trunking profile
DADO 170 x 57mm
1 x vP180 Main Carrier1 x vP100 Straight Cover2 x vP110 Curved Cover
CAbLE CAPACITy
Type of Conductor Size
Cable Factor
Compartment 1 Compartment 2 Compartment 245mm deep box
Full Term CSA (mm2)
1763 3828 610
Term at 45% fill (mm2)
793 1722 274
Power cables Number of cables at 45% fill
PVC
stranded
1.5mm2 8.6 92 200 31
2.5mm2 12.6 62 136 21
4mm2 16.6 47 103 16
6mm2 21.2 37 81 12
Data Cables Number of cables at 45% fill (a) and full capacity (b)
a b a b a b
Cat 5e UTP 5.5mm dia. 30.2 26 58 0 0
Cat 5e STP 6.0mm dia. 36.0 22 48 0 0
Cat 6 UTP 6.5mm dia. 42.2 18 41 0 0
Cat 6 STP 7.0mm dia. 49.0 16 35 0 0
57mm
170mm
Compartment CSA1 = 1763 mm2
2 = 3828 mm2
AssemblyProfile 1 = 1.60 Kg/m
Wall ThicknessVP100 = 1.7mmVP110 = 1.7mmVP180 = 2.0mm
2
1
1
TRuNKING COMPONENTS
List No. vP180 vP100 vP110
Description Main Carrier Straight Cover Curved Cover
Std Pack 2 x 3m 10 x 3m 10 x 3m
FITTINGS
List No. vP181 vP182 vP183 vP184 vP185 vP187 vP188
Description Flexible Internal Corner
Flexible External Corner
End Caps (pair)
Joint Cover Flat Angle Flat Tee Adaptor includes Bridge
Std Pack 2 2 1 5 1 1 10
ACCESSORIES
List No. vP129 vP121 vP122 vP123 vP105 vTS1000
Description Socket Spacer 1 Gang back box 45mm Deep
2 Gang back box 45mm Deep
3 Gang back box 45mm Deep
Cable Retainer(outer compartments)
Screw Fixing Kit
Std Pack 10 25 10 5 50 20
FITTINGS
List No. vP30 vx31 vx32 vx33
Description 1.5m Screening Divider 300mm Screen Connecting Cable
500mm Screen Connecting braid
500mm Screen Connecting Cable
Std Pack 10 10 10 10
The PEC steel ground plane acts as a screening divider to allow cable separation distances to be reduced
Used for joining lengths of screening divider
Used for maintaining screen protection around external corners, flat angles and tees
Lower cost alternative toconnecting screening divider around corners
FINISHES
WHI CHA
Prestige 3D is available in White and Charcoal finish. Add relevant suffix to Part No. when ordering i.e. VP180 WHI or VP180 CHA.
A choice of any RAL colour is also available and can be ordered as a special.
Prestige 3D Product Selector
+ +
Prestige 3D Selector / Dimensions
External Corner
VP182 WHI / CHA
End Cap
VP183 WHI / CHA
Internal Corner
VP181 WHI / CHA
Flat Angle up / Down
VP185 WHI / CHA
20
70
13
13
Flat Tee up / Down
VP187 WHI / CHA
20
70
13
13
Joint Cover
VP184 WHI / CHA
Component selection guide
Flat angles and tees
FLAT ANGLES AND TEES DIMENSIONS (mm)
LIST NO DESCRIPTION A b C D
VP185 WHI/CHA Flat Angle 218mm 170mm
VP187 WHI/CHA Flat Tee 202mm 170mm 235mm 170mm
A
A
B
B
C
D
BA
Flat tee cable option
Flat Tee bridgeThe Flat Tee’s bridge can be fitted in two positions increasing the versatility of cable runs whilst maintaining the correct separation and Cat 6 compatibility.
PowerData
Note: Flat Angle and Tee cover mouldings overlap the base so no coupler/joint covers are required
Prestige 3D Technical
Standards and Approvals
The Prestige 3D System is manufactured in accordance with the requirements of BS EN 50085-1:1999 and BS 4662:1970. Copies of test certificates are available upon request. The system complies with all the relevant requirements of the latest edition of the IEE Wiring Regulations (BS 7671). MK has been awarded ISO 9002 accreditation
CE markingAll relevant MK products in this brochure are CE marked, confirmation that they meet the EMC and LV directives.
ManufactureAll trunking components are manufactured from PVCu.
Category 6All Prestige 3D fittings have been designed to comply with Cat 6 data cable manufacturers’ recommendations of a minimum in-service bend radius of four times the outer diameter of the cable, in order to prevent signal deterioration.
AppearancePrestige 3D is manufactured in white. The trunking surface can be painted, if required, after installation.
Performance Strength – Impact Resistance Medium to BS EN 50085 Operating Temperature -5 to +60ºC
Fire performanceThe PVCu materials used in the manufacture of MK products are non-flame propagating in accordance with BS EN 50085-1:1999 and BS EN 61386-1:2004. Extrusion material has achieved classification 1Y in accordance with BS 476-7:1997. Moulding material has achieved 650ºC glow wire rating in accordance with BS EN 60695-2-11:2001.
Thermal propertiesPrestige 3D trunking is designed to accommodate local thermal expansion. Fitting instructions explain the procedure required to deal with the differential movement at the interface with the building fabric. Linear Expansion 4mm over every 3000mm with a temperature rise of 25ºC
Chemical resistanceThe PVCu materials used are non-corrosive and not affected by seawater. It has excellent resistance to mineral acids, alkalis and detergents, good resistance to alcohols, but is liable to attack from solvents such as ketones, aromatics and hydrocarbons.
ElectricalPrestige 3D trunking is non-conductive. Dielectric strength 40 kV/mm in DBP 17 kV/mm in tx oil Resistivity 1014 ohm/cm
biologicalPrestige 3D trunking is resistant to vermin and termites.
WorkabilityPrestige 3D trunking is lightweight and can readily be cut and drilled to suit installation needs with hand tools.
DurabilityPrestige 3D trunking is stable and will maintain its performance characteristics in accordance with the terms and conditions described above.
MaintenanceClip-on covers with optional screw fix and interchangeable accessories provide continuous accessibility for rewiring, extensions and modifications to an installation. Covers and accessories can be cleaned with water and household detergent. The surface can be decorated with commercial paints if required.
Electro Magnetic InterferenceSystem designers should consult with the EMI requirements BS EN 50174-2 (Information technology – Cabling installation Part 2: Installation planning and practices inside buildings) and safety needs of BS 6701. A Parallel Earthing Conductor (product code VP30) is available where required by these standards.
VX32 Screen Connecting Braid VP30 Screening Divider
Prestige 3D
MK Electric offer comprehensive project support, design and technical advice. Please contact our helpline on the number below.
MK Electric
The Arnold Centre Paycocke Road Basildon Essex SS14 3EA United Kingdom Technical Helpline Tel 01268 563720
Customer Service Tel 01268 563404 Literature Helpline Tel 0870 240 3385 E-mail [email protected]
Customer Service Fax 01268 563405 Literature Helpline Fax 0870 240 3386 Website www.mkelectric.co.uk
Registered Office: Honeywell House, Arlington Business Park, Bracknell, Berkshire, RG12 1EB Registered No. 189291 Literature Ref: MK206