Pressure torque curves Slide #2Rev HA

Actuator sizing instructions

The valve torque curves within this catalogue show the break out torque requirements of Habonimball valves as a function of valve size ,seat material and differential pressure across the valve when theball is in the closed position.

To ease sizing work, a 20% safety factor torque line was added, this is a standard safety factor forpneumatic actuator in standard service.

For severe applications Habonim recommend’s the use of the following safety factors:ServiceEmergency shut down (ESD) service 1.8IEC 61508 SIL complaint installation 1.8Cryogenic applications (below 600C) 1.5Valves operated less than once a day 1.5Control valves 1.5MediaGas, dirty (natural gas) 1.5Gas , dry 1.3Chlorine 1.5Viscous slurry (cp>100) 2.0Oil, Thermal oil, lubricant 0.8

Note: use the above instead of the standard safety factor and not on top of it.

Pressure torque curves Slide #3Rev HA

Actuator sizing instructionsGiven the valve size ,differential pressure across the valve, and the seats material you may obtain the valve breakout torque from the following pressure torque curve (page 5 148).

Calculate the valve torque (T)at points corresponding to a, b, c and d by applying the percentages shown in the tablebelow to the valve maximum torque + Safety Factor (SF)

Once the valve torques have been determined, the actuator can be properly sized.

Double acting operation – Select the actuator whose torque output (at a given instrument air pressure), exceeds themaximum torque + SF requirements of the valve.

Spring return operation Fail closed – Select the actuator whose torque output (at a given instrument air pressure),at the end of spring stroke exceeds the torque required (+SF) to close the valve(Td). Also check that the Air endtorque of the actuator exceeds the torque required (+SF) to open the valve (Tb).

Spring return operation Fail Open – Select the actuator whose torque output (at a given instrument air pressure),at the end of air stroke exceeds the torque required (+SF) to close the valve (Tb). Also check that the Spring endtorque of the actuator exceeds the torque required (+SF) to open the valve (Td).

Warning Actuator air start torque and spring start torque must not exceed the valve stem torque limit.

Pos. Fail closed Fail open

A 100% 50%

B 50% 80%

C 50% 100%

D 80% 50%

A

D

BC

Closed OpenValve Position

Torque Valve Closed onLoss of air

Air to open

Spring to close

C

B

AD

Closed OpenValve Position

Torque Valve opened onLoss of air

Spring to open

Air to close

Pressure torque curves Slide #4Rev HA

Low torque seat materials:• PTFE (T)• UHMWPE (U)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port4” Full port,6” Reduced port,8” Reduced port, 6” Full port

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #5Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #5Rev HA

½” valve, PTFE/UHMWPE, MAX P=75 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #6Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #6Rev HA

¾” valve, PTFE/UHMWPE, MAX P=75 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #7Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #7Rev HA

1” valve, PTFE/UHMWPE, MAX P=75 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #8Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #8Rev HA

1 ¼” valve, PTFE/UHMWPE, MAX P=75 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #9Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #9Rev HA

1 ½” valve, PTFE/UHMWPE, MAX P=75 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #10Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #10Rev HA

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #11Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #11Rev HA

2 ½” valve, PTFE/UHMWPE, MAX P=50 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #12Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #12Rev HA

3” valve, PTFE/UHMWPE, MAX P=50 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #13Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #13Rev HA

4” valve, PTFE/UHMWPE, MAX P=50 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #14Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #14Rev HA

4” FB valve, PTFE/UHMWPE, MAX P=50 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #15Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #15Rev HA

6” valve, PTFE/UHMWPE, MAX P=50 Bar

Index

Low Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #16Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #16Rev HA

8” valve, PTFE/UHMWPE, MAX P=50 Bar

Index

Low Torque

Pressure torque curves Slide #17Rev HA

Medium torque Seat materials:•25% Carbon filled PTFE (P)•15% Glass filled PTFE (R)•TFM (A)•VX1 (H)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port4” Full port,6” Reduced port,8” Reduced port, 6” Full port

Slide #17

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #18Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #18Rev HA

½” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=138 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #19Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #19Rev HA

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #20Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #20Rev HA

1” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=138 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #21Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #21Rev HA

1 ¼” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=138 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #22Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #22Rev HA

1 ½” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=138 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #23Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #23Rev HA

2 ” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=138 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #24Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #24Rev HA

2 ½” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=100 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #25Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #25Rev HA

3” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=100 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #26Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #26Rev HA

4” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=100 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #27Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #27Rev HA

4” FB valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=100 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #28Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #28Rev HA

6” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=100 Bar

Index

Medium Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #29Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #29Rev HA

8” valve, CF PTFE/GF PTFE/TFM/VX1, MAX P=100 Bar

Index

Medium Torque

Pressure torque curves Slide #30Rev HA

Semi High torque Seat materials:•PVDF (W)•DELRIN (Y)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port4” Full port,6” Reduced port,8” Reduced port, 6” Full port

Slide #30

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #31Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #31Rev HA

½” valve, PVDF/Delrin, MAX P=138 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #32Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #32Rev HA

¾” valve, PVDF/Delrin, MAX P=138 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #33Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #33Rev HA

1” valve, PVDF/Delrin, MAX P=138 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #34Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #34Rev HA

1 ¼” valve, PVDF/Delrin, MAX P=138 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #35Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #35Rev HA

1 ½” valve, PVDF/Delrin, MAX P=138 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #36Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #36Rev HA

2” valve, PVDF/Delrin, MAX P=138 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #37Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #37Rev HA

2 ½” valve, PVDF/Delrin, MAX P=100 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #38Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #38Rev HA

3” valve, PVDF/Delrin, MAX P=100 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #39Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #39Rev HA

4” valve, PVDF/Delrin, MAX P=100 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #40Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #40Rev HA

4” FB valve, PVDF/Delrin, MAX P=100 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #41Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #41Rev HA

6” valve, PVDF/Delrin,MAX P=100 Bar

Index

Semi-High Torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #42Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #42Rev HA

8” valve, PVDF/Delrin, MAX P=100 Bar

Index

Semi-High Torque

Pressure torque curves Slide #43Rev HA

High torque Seat materials:•Carbon filled PEEK (K)•Virgin PEEK (L)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port4” Full port,6” Reduced port,8” Reduced port, 6” Full port

Slide #43

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #44Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #44Rev HA

½ ” valve, CF PEEK/Virgin PEEKMAX P=138 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #45Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #45Rev HA

¾” valve,CF PEEK/Virgin PEEKMAX P=138 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #46Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #46Rev HA

1” valve, CF PEEK/Virgin PEEK MAX P=138 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #47Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #47Rev HA

1 ¼” valve, CF PEEK/Virgin PEEK,MAX P=138 Bar

High torque

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #48Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #48Rev HA

1 ½” valve, CF PEEK/Virgin PEEKMAX P=138 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #49Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #49Rev HA

2” valve, CF PEEK/Virgin PEEKMAX P=138 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #50Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #50Rev HA

2 ½” valve, CF PEEK/Virgin PEEKMAX P=100 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #51Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #51Rev HA

3” valve, CF PEEK/Virgin PEEKMAX P=100 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #52Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #52Rev HA

4” valve, CF PEEK/Virgin PEEKMAX P=100 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #53Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #53Rev HA

4” FB valve, CF PEEK/Virgin PEEKMAX P=100 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #54Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #54Rev HA

6” valve, CF PEEK/Virgin PEEKMAX P=100 Bar

High torque

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #55Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #55Rev HA

8” valve, CF PEEK/Virgin PEEKMAX P=100 Bar

High torque

Index

Pressure torque curves Slide #56Rev HA

Semi High torque High Pressure valvetorque Seat materials:•PVDF (W)•DELRIN (Y)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port

Slide #56

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #57Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #57Rev HA

½” valve, PVDF/DelrinMAX P=400 Bar

Semi-High torqueHigh Pressure Valves

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #58Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #58Rev HA

¾” valve, PVDF/DelrinMAX P=400 Bar

Semi-High torqueHigh Pressure Valves

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #59Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #59Rev HA

Semi-High torqueHigh Pressure Valves

1” valve, PVDF/DelrinMAX P=400 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #60Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #60Rev HA

Semi-High torqueHigh Pressure Valves

1 ¼” valve, PVDF/DelrinMAX P=400 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #61Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #61Rev HA

Semi-High torqueHigh Pressure Valves

1 ½” valve, PVDF/DelrinMAX P=400 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #62Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #62Rev HA

Semi-High torqueHigh Pressure Valves

2” valve, PVDF/DelrinMAX P=400 Bar

Index

Pressure torque curves Slide #63Rev HA

High torque “High Pressure valve”torque Seat materials:•PVDF (W)•DELRIN (Y)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port

Slide #63

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #64Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #64Rev HA

½” valve, CF PEEK/Virgin PEEKMAX P=400 Bar

High torqueHigh Pressure Valves

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #65Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #65Rev HA

¾” valve, CF PEEK/Virgin PEEKMAX P=400 Bar

High torqueHigh Pressure Valves

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #66Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #66Rev HA

High torqueHigh Pressure Valves

1” valve, CF PEEK/Virgin PEEKMAX P=400 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #67Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #67Rev HA

High torqueHigh Pressure Valves

1 ¼” valve, CF PEEK/Virgin PEEKMAX P=400 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #68Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #68Rev HA

High torqueHigh Pressure Valves

1 ½” valve, CF PEEK/Virgin PEEKMAX P=400 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #69Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #69Rev HA

High torqueHigh Pressure Valves

2” valve, CF PEEK/Virgin PEEKMAX P=400 Bar

Index

Pressure torque curves Slide #70Rev HA

Medium torque Cryogenic seat materials:• CF PTFE NRG (P)• TFM (A)

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #71Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #71Rev HA

½” valve, CF PTFE/TFM, MAX P=50 Bar

Index

Medium TorqueCryogenic

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #72Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #72Rev HA

¾” valve, CF PTFE/TFM, MAX P=50 Bar

Index

Medium TorqueCryogenic

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #73Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #73Rev HA

1” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #74Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #74Rev HA

1 ¼” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #75Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #75Rev HA

1 ½” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #76Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #76Rev HA

Medium TorqueCryogenic

2” valve, CF PTFE/TFM, MAX P=50 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #77Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #77Rev HA

2 ½” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #78Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #78Rev HA

3” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #79Rev HA

4” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #79Rev HA

4” valve, CF PTFE/TFM, MAX P=50 Bar

Medium TorqueCryogenic

Index

Pressure torque curves Slide #80Rev HA

High torque Cryogenic seat materials:• PCTFE (C)• TFM (A)½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port4” Full port,6” Reduced port,8” Reduced port, 6” Full port

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #81Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #81Rev HA

½” valve, CF PTFE/TFM, MAX P=50 Bar

Index

High TorqueCryogenic

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #82Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #82Rev HA

¾” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #83Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #83Rev HA

1” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #84Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #84Rev HA

1 ¼” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #85Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #85Rev HA

1 ½” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #86Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #86Rev HA

High TorqueCryogenic

2” valve, CF PTFE/TFM, MAX P=50 Bar

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #87Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #87Rev HA

2 ½” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #88Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #88Rev HA

3” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #89Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #89Rev HA

4” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #90Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #90Rev HA

4” FB valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #91Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #91Rev HA

6” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #92Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #92Rev HA

8” valve, CF PTFE/TFM, MAX P=50 Bar

High TorqueCryogenic

Index

Pressure torque curves Slide #93Rev HA

MTM seat materials:

½” Reduced port, ¼” & 3/8” Full port3/4” Reduced port, ½” Full port1” Reduced port, 3/4” Full port1 ¼” Reduced port, 1” Full port1 ½” Reduced port, 1 ¼” Full port2” Reduced port, 1 ½” Full port2 ½” Reduced port, 2” Full port3” Reduced port, 2 ½” Full port4” Reduced port, 3” Full port6” Reduced port,8” Reduced port, 6” Full port

Home

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #94Rev HAPressure torque curvvvvvvvvvvvvvvvvveeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeesssssssssssssssssssssssssssssssssssssssssssssss

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #94ReRev v HAHAHH

½” valve, MAX P=400 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #95Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #95Rev HA

¾” valve, MAX P=400 Bar

MTM valve

Index

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #96Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #96Rev HA

1” valve, MAX P=350 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #97Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #97Rev HA

1 ¼” valve, MAX P=275 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #98Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #98Rev HA

1 ½” valve, MAX P=200 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #99Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #99Rev HA

2” valve, MAX P=200 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #100Rev HA

2 ½” valve, MAX P=150 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #100Rev HA

2 ½” valve, MAX P=150 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #101Rev HA

3” valve, MAX P=175 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #101Rev HA

3” valve, MAX P=175 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #102Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #102Rev HA

4” valve, MAX P=100 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #103Rev HAPressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #103Rev HA

6” valve, MAX P=75 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #104Rev HA

8” valve, MAX P=50 Bar

Index

MTM valve

Pressure torque curves

The information given hereunder must be read in conjunction with the Habonim actuator sizing instructions Figures shown include 20% safety factor for standard application. For non-standard applications, please refer to Habonim

actuator sizing instructions.All data refers to values tested at ambient temperature

In order to verify temperature suitability of seat, please refer to seat material selection guide.

Slide #104Rev HA

8” valve, MAX P=50 Bar

Index

MTM valve