Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
Presentation to NRCU.S. EPRFSAR Chapter 4 Open Item RAIs
AREVA NPMay 27, 2010
AAREVA
FSAR Chapter 4 fOpen Item RAIs
Oo Draft responses have been provided to the staff in advance ofthis meeting
lo Today's presentations are intended to facilitatethe draft responses
No Goal of today's discussion is to assure that theprovide the information requested
discussion of
responses
AAREVAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.2
FSAR Chapter 4Open Item RAIs
00.RAIOo-RAI
00.RAI
00.RAI
00.RAI
339
343
.344
366
367
-4
-2
-2-1
-1
questions
questions
questions
question
question
AAREVAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.3
SAR UChapter 4RAI 339
Oo Question 04.02-17 - AREVA NP is requested to acknowledgereceipt of this open item which states that ANP-10285P iscurrently under review by the staff.
Oo Response to 04.02-17 - AREVA NP acknowledged receipt ofthis open item.
AU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.4 AR EVA
. . . - .
FSAR Chapter 4RAI 339
No Question 04.05.02-9 - This question is related to the use ofStellite 6 for hardfacing the Radial Key Inserts. The staffrequested that the applicable ASME code specifications forStellite 6 be added to the FSAR.
lo Response to 04.05.02-9 - The applicable ASME codespecifications were added to the FSAR.
AAREVAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.5
FSA Chapter 4RAI 339
Io Question 04.05.02-10 - AREVA NP was requested to add aCOL item related to consideration of neutron fluence in thedesign of reactor internals.
Io Response to 04.05.02-10 - A COL condition was added to theFSAR.
AU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.6 AR EVA
FSAR Chapter4RAI 339 L• •
lo Question 04.05.02-11 - AREVA NP was requested to provide adiscussion of the prevention of notches on the vertical keysand keyways in the heavy reflector.
O Response to 04.05.02-11 - A discussion of the prevention ofnotches on the vertical keys and keyways in the heavyreflector was provided.
AU.S EPR FSAR Chanter 4 Onen Item RAIs - May 27. 2010 - D.7 AR EVA
FSAR Chapter 4 fRAI 343
Oo Question 04.05.01-6 - AREVA NP was requested to modify theFSAR to reflect the use of F347 material.
Po Response to 04.05.01-6 - AREVA NP respondedmaterial is not used in the U.S. EPR and that theterm in the referenced RAI response was a typo.
that F347use of that
AARE VAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.8
FSAR Chapter 4RAI 343
Oi Question 04.05.01-7 - AREVA NP was requested to notify thestaff when the ASME code case N-785 was approved.
Oo Response to 04.05.01-7 - The response states that the ASMEcode case has been approved and describes the basis for theapproval. The reference in the FSAR to this code caseconstitutes a request to use this material as required by 10CFR 50.55a.
AU.S. EPR FSAR Chapter 4 Ooen Item RAIs - May 27, 2010 - D.9 AR EVA. . . .... i I 4 • i
FSAR Chapter 4RAI 344
No Question 04.03-27 - AREVA NP was requested to add a COLitem related to the benchmarking of the method in BAW-2241 PA.
l Response to 04.03-27 - A COL item related to thebenchmarking of the method in BAW-2241 PA was added tothe FSAR.
AAR EVAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.10
FSAR Chapter 4RAI 344 .
lo Question 04.03-28 - AREVA NP is requested to acknowledgereceipt of this open item which states that ANP-10286P iscurrently under review by the staff.
Oo Response to 04.03-28 - AREVA NP acknowledged receipt ofthis open item.
AU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.11 AR EVA
m I • w w
FSAR Chapter 4 11-,•,RAI 366 L
lo Question 04.06-13 - AREVA NP was requested to clarify anapparent discrepancy in the FSAR regarding the descriptionsof the credit taken for reactivity controls systems other thanreactor trip.
Io Response to 04.06-13 - AREVA NP provided a clarification ofthe descriptions in the FSAR. No change was necessary tothe FSAR.
AU.S. EPR FSAR ChaDter 4 Open Item RAIs - May 27, 2010 - p.12 AR EVA
FSAR Chapter4RAI 367 L
Io Question 04.06-14 - AREVA NP was requested to provide adescription of how the limitations in the SE for ANP-10287Pwould be implemented and verified.
lo Response to 04.06-14 - AREVA NP provided a description ofhow the limitations in the SE for ANP-10287P would beimplemented and verified. A COL item was added to the FSAto address one of the limitations in the SE.
R
AAR EVAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p. 1 3
FSAR Chapter 4Open Item RAIs
Pp Future Actions
IP Schedule
AAREVAU.S. EPR FSAR Chapter 4 Open Item RAIs - May 27, 2010 - p.14
Responseto
Request for Additional Information No. 339, Supplement 2
01/08/2010
U.S. EPR Standard Design CertificationAREVA NP Inc.
Docket No. 52-020SRP Section: 04.02 - Fuel System Design
SRP Section: 04.05.02 - Reactor Internal and Core Support Structure Materials
Application Section: FSAR Chapter 4
QUESTIONS for Reactor System, Nuclear Performance and Code Review (SRSB)QUESTIONS for Component Integrity, Performance, and Testing Branch 1
(API O00/EPR Projects) (CIBI)
AREVA NP Inc.
Response to Request for Additional Information No. 339, Supplement 2U.S. EPR Design Certification Application Page 2 of 5
Question 04.02-17:
OPEN ITEM
Throughout the U.S. EPR Final Safety Analysis Report (FSAR) Tier 2, Section 4.2, AREVANP refers to licensing topical report ANP-10285P, "U.S. EPR Fuel Assembly Mechanical DesignTopical Report." This document is currently under review by the NRC staff. This RAI is createdto track an open item associated with this review. It will be closed upon completion of the reviewby the NRC staff. AREVA Is requested to acknowledge receipt of this open item.
Response to Question 04.02-17:
AREVA NP acknowledges receipt of this open item.
FSAR Impact:
The U.S. EPR FSAR will not be changed as a result of this question.
AREVA NP Inc.
Response to Request for Additional Information No. 339, Supplement 2U.S. EPR Design Certification Application Page 3 of 5
Question 04.05.02-9:
OPEN ITEM:
AREVA's response to RAI No. 50, Question 04.05.02-1 stated that Stellite 6 Is used forhardfacing the Radial Key Inserts, Upper Core Plate Guide Pins and Inserts. Your responsealso lists the applicable ASME specifications for the Stellite 6 (ASME SFA5.21 ClassificationERCCoCr-A, ASME SFA 5.21 Classification ERCoCr-A and ASME SFA5.13 ClassificationECoCr-A) that could be used for weld deposition of the Stellite 6 onto the applicablecomponents base material. The staff requests that the applicable ASME code specifications forthe hardfacing material, Stellite 6, be included in the U.S. EPRFSAR, Tier 2, Table 4.5.2.
Response to Question 04.05.02-9:
U.S. EPR FSAR Tier 2, Table 4.5-2 will be revised to include the welding•filler materialspecifications ASME SFA-5.21 ERCCoCr-A or ERCoCr-A nd ASME SFA-5.13 ECoCr-A forStellite 6 hardfacing materials.
FSAR Impact:
U.S. EPR FSAR Tier 2, Table 4.5-2 will be, revised as described in the response and indicatedon the enclosed markup.
AREVA NP Inc.
Response to Request for Additional Information No. 339, Supplement 2U.S. EPR Design Certification Application Page 4 of 5
Question 04.05.02-10:
OPEN ITEM:
In response to RAI No. 50, Question 04.05.02-4, your response stated that the reentrant cornersof the heavy reflector are estimated to experience a peak 60-EFPY neutron fluence of 8.56x1 02
n/cm 2 (E>1.0 MeV) which exceeds the threshold for IASCC and void swelling. Therefore,AREVA plans on participating in the Industry EPRI/MRP programs to manage IASCC and voidswelling to screen the heavy reflector for IASCC and void swelling. To verify that IASCC andvoid swelling does not impact the safety function of the heavy reflector or create loose parts, anaugmented ASME Code, Section XI inspection program will be'developed. Therefore, the staffrequests that AREVA include in the U.S. EPR DCD, a license condition or a COL Action Item toaddress this issue.
Response to Question 04.05.02-10:
U.S. EPR FSAR Tier 2, Section 4.5.2.1 will be modifie'do include consideration of neutronfluence in design of the reactor internals and evalua tion of the. m:aterials relative to susceptibilityto known aging degradation mechanisms such as irradiation-assisted stress corrosion crackingand void swelling.
U.S. EPR FSAR Tier 2, Table 1.8-2 and Section 3.9.3 will be modified to also require the COLapplicant to address reactor internals materials with regard to known aging degradationmechanisms such as irradiation assisted stress corr6sion, cracking or void swelling.
FSAR Impact:
U.S. EPR FSAR Tier 2, Se•tion 3.9.3, Section 4.&52-1, and Table 1.8-2 will be revised asdescribed in the response and indicated 6n•t•he enclosed markup.
AREVA NP Inc.
Response to Request for Additional Information No. 339, Supplement 2U.S. EPR Design Certification Application Page 5 of 5
Question 04.05.02-11:
OPEN ITEM:
AREVA's response to RAI No. 50, Question 04.05.02-2b did not address the staffs request for adiscussion on the prevention of notches on the vertical keys and keyways that can act as stressconcentrations and crack initiation sites, which could lead to the loss of function of the heavyreflector. Therefore, the staff requests a discussion on this topic.
Response to Question 04.05.02-11:
Under normal and upset conditions, the heavy reflector slabs are not subject to significantprimary loads. Loading during these conditions is mainly attributable to the loading induced bythe preload of[ , ] tie rods which hold the heavy reflector a~sembly together and attach it tothe lower support plate of the core barrel assembly and thermal loading (from both gammaheating and surrounding fluid temperature). The vertical keys within the heavly reflectorassembly mainly provide lateral restraint between the, havy reflector slabs du'rinig faultedconditions; however, they may also be credited for'vertical restraint during faulted conditions inconjunction with the tie rods. Specific configurations are evaluated with consideration of anynotch affects (and associated stress concentration factbrs) to confirm that the structural andfatigue requirements of ASME Section II, Subsection NG are met as specified in U.S. EPRFSAR Tier 2, Section 3.9.5.2
The width of the vertical key is controlled for a'distance [• ] above and below each of theheavy reflector slab Interfaces toilprovide a clearance fit [ .. Thelateral restraint function of the'.Veicai. keys is provided only within these portions of the verticalkeys. For the remainder of the vertical key length,,.greater clearances [. ' between thevertical keys and the heavy reflector slabs are provided. For the keyway within the heavyreflector slabs, the reentrant corners are pruvided with a small radius for the full length of thekeyway to preclude sharp notche.e
Each end of the vertical keys is configured with a 'T' connection where the width is increased toengage with ithe upper and'lower heavy reflector slabs for the vertical restraint function. Duringassembly, a •gap is provided between the vertical keys and the lower slab so that vertical keys Iheavy reflector slabs are nots!ubjected to tensile loading during normal operation. Within thekeyway opening in the uppdr.':and lower slabs, a small radius is provided for all reentrant cornersto preclude sharp notches..
FSAR Impact:
The U.S. EPR FSAR will not be changed as a result of this question.
U.S. EPR Final SafetyAnalysis Report Markups
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
Table 1.8-2-U.S. EPR Combined License Information ItemsSheet 17 of 47
Antla;- Ae44enReq~ied RequiFed19yGQb- by GQ1
Item No. Description Section App4,ee• Mnde.
3.8-12 A COL applicant that references the U.S. EPR 3.8.5.7 ydesign certification will describe the program toexamine inaccessible portions of below-gradeconcrete structures for degradation andmonitoring of groundwater chemistry.
3.8-13 A COL applicant that references the U.S. EPR 3.8.5.7:design certification will identify if any site-specific settlement monitoring requirements arerequired for Seismic Category I foundationsbased on site-specific soil conditions.
3.8-14 A COL applicant that references the U.S. EPR 3.8?4.4.5 ydesign certification will describe the design andanalysis procedures used for buried conduit andduct banks, and buried pipe and pipe ducts.
3.8-15 A COL applicant that references the U.S. EPR 3.8. 4.4.5 ydesign certification will use results-from site-.specific investigations to determine the routingof buried pipe and pipe:duc ts.,
3.8-16 A COL applicant~that references the U.S. EPR 3.8.4.4.5 Ydesign certification will perform geotechnicalengineering analyses to determine if. the surfaceload will cause laterial and/or verticaldisplacement, of bearin gsoil for the buried pipeand pipe ducts 'nd consider the effect of wide oreixt'ra heavy loadsK.,
3.9-1 A COL applicant th~treferences the U.S. EPR 3.9.2.4 Ydesign certificationwi]1 submit the results fromthe vibration assessment program for the U.S.EPR RPV inteirnals, in accordance with RG 1.20.
3.9-2 A COL applicant that references the U.S. EPR 3.9.3 Ydesign certification will prepare the designspecifications and design reports for ASME Class1, 2, and 3 components, piping, supports andcore support structures that comply with and arecertified to the requirements of Section III of theASME Code.
Tier 2 Revision 2-Interim Page 1.8-22
.7--i- -
AOVOM%ý
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
Table 1.8-2-U.S. EPR Combined License Information ItemsSheet 18 of 47
Ae ,, Ael.,-.e.ue-4 Requi~ed
104.05.02-1 oy-GQb- -- y, G""Item No. I Description Section A-pllea,-, Hl^"de"
The COL applicant will address the results andconclusions from the reactor internals materialreliability programs applicable to the U.S. EPRreactor internals with regard to known agingdegradation mechanisms such as irradiation-assisted stress corrosion cracking or voidswelling.
3.9-3 A COL applicant that references the U.S. EPR 3.9.3.1.1 9.design certification will examine the feedwaterline welds after hot functional testing prior tofuel loading and at the first refueling outage, inaccordance with NRC Bulletin 79-13. A COLapplicant that references the U.S. EPR designcertification will report the results of inspectionsto the NRC, in accordance with NRC Bulletin79-13.
3.9-4 As noted in ANP-10264NP-A, a COL applicant 3.9.3.1.1that references the U.S., EPR design certificationwill confirm that thermal 'deflections do notcreate adverse conditions during hot functionaltesting.
3.9-5 As noted in ANP-10264NP-A, should a COL 3.9.3.1.1 ¥applicant that references the U.S. EPR designcertification find it necessary to route Class 1, 2,and 3 piping not included in, the U.S. EPR designcertification so that itis exposed to wind andtornadoes, the design must withstand the plantdesign7basis loads for this event.
3.9-6 A COL applicant that references the US EPR 3.9.6.3 ydesign certification will identify any additionalsite-specific valves in Table 3.9.6-2 to beincluded within the scope of the IST program.
3.9-7 A COL applicant that references the U.S. EPR 3.9.6design certification will submit the preservicetesting (PST) program and IST program forpumps, valves, and snubbers as required by 10CFR 50.55a.
Tier 2 Revision 2-Interim Page 1.8-23Tier 2 Revision 2--Interim Page 1.8-23
AU.S. EPR FINAL SAFETY ANALYSIS REPORTEP RThis section refers to U.S. EPR Piping Analysis and Pipe Support Design TopicalReport (Reference 2) for information related to the design and analysis of safety-related piping. This topical report presents the U.S. EPR code requirements,acceptance criteria, analysis methods, and modeling techniques for ASME Class 1, 2,and 3 piping and pipe supports. Applicable COL action items in the topical report areidentified in the applicable portions of this section. The U.S..EPR design is based onthe 2004 ASME Code, Section III, Division 1, with no addenda subject to thelimitations and modification identified in 10 CFR 50.55a(b)(1) and the piping analysis
criteria and methods, modeling techniques, and pipe support criteria described inReference 2.
A design specification is required by Section III of the ASME Code for Class 1,2, and 3components, piping, supports, and core support structures. In addition, the ASMECode requires design reports for all Class 1, 2, and3 components, piping, supports andcore support structures documenting that the as-designed and as7built configurationsadhere to the requirements of the design specification. A COL applicant thatreferences the U.S. EPR design certification will prepare the design specifications anddesign reports for ASME Class 1, 2, and 3 components, piping, supports and core
04.05.02-10 . support structures that comply with and are certified to the requirements of Section III
of the ASME Code. The COLUpY licant will adiresS the resudlts and conclusions fromthe reactor internals material riliabiLity programs applicable to the U.S. EPR reactorinternals with regard to knownzifiing degradation mechanisms such as irradiation-assisted stress corr6sion cracking.or void swelling addressed in Section 4.5.2.1,
Other sections that relate to this section are described below:
a Section 3.9.6 describes the snubber inspection and test program.
S Section 3.10 describes the methods and criteria for seismic qualification testing ofSeismic Category I rmechanical equipment and a description of their seismicoperability criteria.
* Section 3.12 describes the design of systems and components that interface withthe RCS with regard to intersystem LOCAs.
* Section 3.13 describes bolting and threaded fastener adequacy and integrity.
" Section 5.2.2 describes the pressure-relieving capacity of the valves specified forRCPB.
" Section 10.3 describes the pressure-relieving capacity of the valves specified forthe steam and feedwater systems.
3.9.3.1 Loading Combinations, System Operating Transients, and Stress Limits
Section 3.9.3.1.1 describes the design and service level loadings used for the design ofASME Class 1, 2, and 3 components, piping, supports, and core support structures,
Tier 2 Revision 2--Interim Page 3.9-43
oU.S. EPR FINAL SAFETY ANALYSIS REPORTEPR4.5.2.1 Materials Specifications
The major components for the reactor internals are fabricated from austenitic stainless
steel except for the hold-down spring, which is made from martensitic stainless steel
and pins and inserts which are coated with Stellite 6 or equivalent which is a cobaltalloy. The materials specifications for the reactor internals and core support materialsincluding weld filler materials are listed in Table 4.5-2-Reactor Vessel InternalMaterials, which includes the use of ASME Code Case N-60-5 which is listed as an
acceptable code case under RG 1.84. There are no other materials used in the reactorinternals or core support structures that are not otherwise allowed under ASME Code,
Section III, Subsection NG-2120 (Reference 4). Reactor internals and core support
structure weld filler materials are specified in ASME BPV Code, Section II104.05.02-10 9-•Reference 2) which is in accordance with GDC 1 and 10•CFR 50.55(a).
Design of the reactor internals considers the e'stimated peak neutron. fluence to whichthe materials may be subjected. The reactor: internals materials are evaluated for
susceptibility to known aging degradation mechanisms such as irradiation-assistedstress corrosion craclihg and void swelling that hive been identified in current
operating pressurized water reactors and are being addressed in the reactor internalsmaterial reliability .rograim . __ ::___ _ ___.
4.5.2.2 Controls on Welding
The controls on welding of austeritic stainless steel pressure boundary components
provided in Section 5.2.3 apply to the welding of reactor internals and core support
components. When Section 5.2.3 is applied to the reactor internals and core supportmaterials, ASME BPV Code, Section III (Reference 4) applies as in accordance withGDC 1 and 10 CFR 50.55(a).
4.5.2.3 Nondestructive Examination
Nondestructive examination (NDE) of base materials is in accordance with ASME
Code Section III, Division I, NG-2500 (Reference 4). The NDE methods andacceptance criteria for welds are in accordance with the requirements of the ASMECode Section III, Division 1, NG-5000 (Reference 4) and GDC 1 and 10 CFR 50.55(a).
4.5.2.4 Fabrication and Processing of Austenitic Stainless Steel Components
The details provided in Section 5.2.3 concerning the processing, inspections, and tests
on unstabilized austenitic stainless steel components to minimize susceptibility tointergranular corrosion caused by sensitization are applicable to the austenitic stainlesssteel materials used in the reactor internals and core support structures, Section 5.2.3
verifies compliance of reactor internals and core support structures with RG 1.44. The
reactor internals and core support structures are fabricated from low carbon austenitic
stainless steels which are heat treated in accordance with RG 1.44 to minimize their
Tier 2 Revision 2-Interim Page 4.5-4Tier 2 Revision 2-Interim Page 4.5-4
10001111ý
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
Table 4.5-2--Reactor Vessel Internal Materials
Component Material SpecificationsLower Internals Assembly ASME SA-182 Grade F304LN (see Notes 1&2
ASME SA-336 Grade F304LN (see Notes 1&2)
ASME SA-240 Type 304L-N (see Notes 1&2)
ASME SA-479 Type 304hN (see Notes 1&2j
ASME SA-479 Type 316 Strain Hardened Level 1
(Code Case N-60-5) Carbon content shall be 0.03wtO% or lessASME SB-168 UNS-N06690
ASME SB-637 UNS-N07750, Type 2[ Stellite 6 (see Note 3) or equivalent (hard facing)
Upper Internals Assembly ASME SA-182 Grade F304LN (see.Notes A.21
ASME SA-376 Grade TP304N (see Notes 1&2)
ASME SA-240 Type 304!.44 .see Notes M&2
ASME SA-479 Type 304-4N_ see Notes l&2)
ASME SA-479 Type 316 Strain Hardened Level 1
(Code Case N-60-5) Carbon content shall be 0.03 wt% or less04.05.02-9 Stellite 6 (seeNote 3_or equivalent (hard facing)
Heavy Reflect ASME SA-336 Grade F304N (see Notes 1&2__)
ASME SA-240 Type 304-i (see Notes l&2ASME SA-336 Grade F304LN (see Notes 1&2)
'ASMEýSA-479 Type 304L-N see Notes I&2
ASME SA-479 Type 316 Strain Hardened Level 1(Code Case N-60-5) Carbon content shall be 0.03.wxO/o or less
Stellite 6 (see Note 3) or equivalent (hard facing)
Control Rod Guide Assembly ASME SA-182 Grade F304L-N (see Notes 1&2)ASMESA-240 Type 304LN- (see Notes l&2)
ASME SA-479 Type 30411 (see Notes !&2ýASME SA-376 Grade TP304LN (see Notes 1&2)
Hold Down'Spring ASME SA-182 Grade F6NM
Reactor Vessel Internals Type 308L/309L/316L austenitic stainless steel per SFA 5.4, 5.9, orWelds 5.22
Notes:
1. Solution annealed and rapidly cooled.
2. Carbon content not exceeding 0.03 wt%.
3. ASME SFA-5.21 ERCCoCr-A or ERCoCr-A, ASME SFA-5.13 ECoCr-A.
104.05.02-10 -1
Next File
Tier 2 Revision 2-Interim Page 4.5-8
U.S. EPR FINAL SAFETY ANALYSIS REPORT
EPR3.9.5.1.2.6 Flow Distribution Device
The flow distribution device is located below, and attached to, the LSP. The flow
distribution device is composed of a distribution plate and support columns. The flow
distribution device provides a homogeneous flow distribution between the ISP holes.
3.9.5.1.2.7 Heavy Reflector
The heavy reflector is located inside the core barrel between the core and core barrelshells. The heavy reflector increases neutron efficiency due to its neutron reflective
properties, protects the RPV from radiation-induced embrittlement, improves the
long-term mechanical behavior of the lower internals, and provides lateral support to
maintain the geometry of the core. To avoid any welded or bolted connections close
to the core, the heavy reflector consists of stacked slabs positioned one above the other
(see Figure 3.9.5-3-Reactor Pressure Vessel Heavy Reflector). The heavy reflector
rests on the LSP, but does not contact the UCP. The internal contour of the slabs
conforms to the core, while the external contour is cylindrical. The top slab is fitted
with alignment pins that extend through the UCP to provide proper alignment
Since the heavy reflector is located between the core and the core barrel, it limi the
core bypass flow at the core periphery. It also provides lateral support to the cor and
contributes to the decrease of neutron fluence on the RPV inner wall.
Additional information on the heavy reflector is provided in 4.3Nuclear Design.
3.9.5.1.3 d Vertical keys are installed into keyways machined into the external contour ofthe slabs to provide additional lateral and vertical restraint. The reentrantcorners of the keyways within the slabs are provided with a small radius.
Internals, and are described in further detail below. The primary functions of the
upper internals are:
" Support, locate, restrain, protect, and guide the core components.
* Direct the coolant flow from the core outlet to the RPV outlet nozzles.
* Permit core loading, unloading, and reloading.
" Support, align, and protect the rod cluster control assemblies (RCCAs).
" Guide, support, and protect the incore instrumentation.
The upper internals consist of the:
" Upper support assembly (including the flange, shell, and USP).
" Upper core plate.
" Control rod guide assemblies (CRGAs).
Tier 2 Revision 2-Interim Page 3.9-80
Response to
Request for Additional Information No. 343, Supplement 1
12/16/2009
U.S. EPR Standard Design CertificationAREVA NP Inc.
Docket No. 52-020SRP Section: 04.05.01 - Control Rod Drive Structural Materials
Application Section: 4.5.1
QUESTIONS for Component Integrity, Performance, and Testing Branch I(AP1000/EPR Projects) (CIB1)
AREVA NP Inc.
Response to Request for Additional Information No. 343, Supplement 1U.S. EPR Design Certification Application Page 2 of 3
Question 04.05.01-6:
OPEN ITEM
Figure 05.02.03-12-1 in RAI response 05.02.03-12, dated November 10, 2008, indicates thatF347 material will be used to fabricate part: of the CRDM pressure housing. However, Table 5.2-2 does not list a forging specification for Grade 347 material. The staff requests that theapplicant modify FSAR Table 5.2-2 to list material specifications and grades for all CRDMpressure boundary components.
Response to Question 04.05.01-6:
Three parts were inadvertently marked with the label "F347" in FiPgure 05.02.03-12-1 (i.e., Parts1, 3, and 5) of the response to RAI 88, Question 05.02.03-12. The label 'F347" should not havecontained the letter F. These parts are fabricated from ASME material Specification SA-479Grade 347, which is already listed in U.S. EPR FSAR Tier 2, Table 5.2-2.
FSAR Impact:
The U.S. EPR FSAR will not be changed as a result of this•question.
AREVA NP Inc.
Response to Request for Additional Information No. 343, Supplement 1U.S. EPR Design Certification Application Page 3 of 3
Question 04.05.01-7:
OPEN ITEM
The staff requested, in RAI 88 Question 05.02.03-1, that the applicant delete SA-479 UNSS41500 from Table 5.2-2 for use in the CRDM pressure housing, provide an alternative materialor take the appropriate steps to have SA-479 UNS S41500 included in Table 2A by ASMECode, Section II1. The applicant responded, by letter dated November 10, 2008, and stated thatit has submitted a request to ASME Code to extend the properties currently provided in SectionII Part D for SA-182 Grade F6NM (UNS S41500) to SA-479 (UNS S41 500) material. Theapplicant stated that it expects the Code Case to be issued in the near future. The staffrequests that the applicant notify the NRC staff when ASME Code has approved the code caserequested by the applicant.
Response to Question 04.05.01-7:
* The request to extend the properties currently provided in Section II Part D for SA-182/182MGrade F6NM to SA-479/479M UNS S41500 was approved October 12, 2009 by ASME asCode Case N-785.
* The basis for approval of this code case is that the chemical composition, materialproperties, and heat treatment requirements for SA-182/182M Grade F6NM and SA-479/479M UNS S41500 are virtually identical. As this code case has not yet been added toRG 1.84, U.S. EPR FSAR Tier 2, Section 5.2.3.1 will be revised to specifically addressacceptability of this code case for use.
" The appropriate control rod drive mechanism; (CRDM) materials listed in U.S. EPR FSARTier 2, Table 5.2-2 for "Control Rod Drive Mechanism" and in U.S. EPR FSAR Tier 2,Section 4.5.1.1 and Section 4.5.1.3 will be modified to reflect this code case. This codecase will also be added to U.S. EPR FSA RTier 2, Table 5.2-1.
" Code cases listed'in U.S. EPR FSAR Tier 2, Table 5.2-1 include those applicable to ASMESection Xl and the ASME OM Code. U.S. EPR FSAR Tier 2, Section 5.2.1.2 will be revisedto clarify that code cases used in the U.S. EPR design certification are listed in Table 5.2-1,not just code cases applicable to ASME Section II1.
FSAR Impact:
U.S. EPR FSAR Tier 2, Section 4.5.1.1, Section 4.5.1.3, Section 5.2.1.2, Section 5.2.3.1, Table5.2-1, and Table 5.2-2 will be revised as described in the response and indicated on theenclosed markup.
U.S. EPR Final SafetyAnalysis Report Markups
1U.S. EPR FINAL SAFETY ANALYSIS REPORT
EPR4.5 REACTOR MATERIALS
4.5.1 Control Rod Drive System Structural Materials
GDC 1 and 10 CFR 50.55(a) establish the requirements regarding structures, systems,and components (SSC) important to safety being designed, fabricated, erected, andtested to quality standards commensurate with the importance of the safety functionsto be performed. The specifications and design requirements of the materials selected
for the control rod drive mechanism (CRDM) are described in Sections 3.9.4, 4.5, and5.2.3.
GDC 14 establishes requirements regarding the reactor coolant pressure boundarybeing designed, fabricated, erected, and tested to hat extiemely low probability ofabnormal leakage, rapidly propagating failure, or ,ross rupt•reThe pressureboundary of the CRDM is designed in accordance with ASME Code and the materialsare selected based on compatibility with their environment as de6rigbed inSections 3.9.4, 4.5, and 5.2.3.
GDC 26 establishes the requirements regarding control rods being capable of reliablecontrol of reactivity changes to• prevent exceeding fuel design limits under conditionsof normal operation, including anticip3ted operatio'nal occurrences. The CRDMmaterial selection and fabrication supp6ridiakble rod movement for reactivity
control, which is addressed in Sections 3.9.4, 4.5, and 5.2.3.
4.5.1.1 Materials Specifications
Parts exposed to reactdr c lan are made of corrosion resistant materials. The CRDM14 . -7 pressure bounIdar materials exposed to reactor coolant include Type 347 stabilized
ai•e•'iitic stainless steel and ASME SA-479 UNS S41500 (Code Case N-785)/SA-182'Grade F6N1 ... S.S41500) martensitic stainless steel. The CRDM pressure boundary%ebolting-studs merials not exposed to reactor coolant include Alloy A-286 austeniticstiniless steel bolting studs as well as martensitic stainless steel nuts. These materials
art li sted in 'Table 5 2-2.
The CRDM pressure boundary materials and pressure boundary weld filler material,which includes Type 347 austenitic stainless steel and alloy 52/52M/152 nickel basealloys, meet the ASME Boiler and Pressure Vessel Code, Section III, Subsection NB(Reference 1). No Alloy 600 base metal or Alloy 82/182 weld metals are used in theCRDM pressure boundary in accordance with GDC 1 and 10 CFR 50.55(a).
Materials used in the CRDM internals are selected based on a proven AREVA designwith 30 years of operating experience. CRDM internals are non-pressure boundaryand non-structural components, thus the CRDM internals material specifications are
not required to be ASME materials. CRDM internals material specifications aretypically per European standards and are listed in Table 4.5-1-Control Rod Drive
Tier 2 Revision 2-intdrim Page 4.5-1
0U.S. EPR FINAL SAFETY ANALYSIS REPORT
austenitic stainless steel used in these applications is ASME SA-479 UNS S41500 (CodeCase N-785)/SA-182 Grade F6NM-(UNS-S4• I•) This material is martensitic stainlesssteel and is delivered in the quenched and tempered condition. The material is
104.05.01-7 tempered between 1050'F and 1120°F as required by the ASME material
* specifications.
Materials other than austenitic stainless steel used in the non-pressure boundarycomponents of the CRDM include martensitic stainless steel, cobalt-chromium alloy,nickel-base materials, and cobalt base material. The materials not used in pressureboundary applications are selected based on a proven German design with 30 years ofoperating experience. Materials are selected for their compatibiity with the reactor
coolant, as described in ASME articles NB-2160 and.NB-3120 (Reference 1).
The martensitic stainless steel base metal used, in the non-pirssure boundarycomponents is delivered in the quenched and tempered condition; tempering isperformed at a temperature to between,1256'F and 14360F.
The cobalt-chromium alloy is delivered in the solution annealed condition.
The nickel-base alloy used is a precipitation hardenable alloy which is extremelyresistant to chemical corrosich iia&u i dation. It is supplied in the solution annealed(followed by quenching) and theirmally zig•dcondition for optimum resistance to stresscorrosion cracking.:.,
The cobalt all,,%is only usied in a ven, small portion of the CRDM where an alternate
material willniot per isa-tisfactorily. It has a very low susceptibility to corrosion.
The sliding surfaces of the latch unit are hard chromium plated. This material is onlyused in a .vey smdll portion of the CRDM where an alternate material will not
'.perform satisfactoril•&9:
4.5.1.4 Cleaning and Cleanliness Control
Cleabliness of the CRDMs is controlled during manufacture and installation per therequiremens of ASME NQA-1-1994 (Reference 3) and RG 1.37 as addressed inSection 5.2.3.
4.5.2 Reactor Internals and Core Support Materials
GDC 1 and 10 CFR 50.55(a) establish the requirements regarding SSC important tosafety being designed, fabricated, erected, and tested to quality standardscommensurate with the importance of the safety functions to be performed. Thespecifications and design requirements of the materials selected for the reactorinternals and core support structures are described in Sections 3.9.5, 4.5, and 5.2.3.
Tier 2 Revision 2-Interim Page 4.5-3Tier 2 Revision 2-Interim Page 4.5-3
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
5.2
5.2.1
5.2.1.1
Integrity of the Reactor Coolant Pressure Boundary
This section describes the measures employed to provide and maintain the integrity ofthe reactor coolant pressure boundary (RCPB) for the plant design lifetime. Consistentwith the definition in 10 CFR 50.2, the U.S. EPR RCPB includes all pressure-containing components, such as pressure vessels, piping, pumps, and valves which arepart of the reactor coolant system (RCS) or connected to the RCS, up to and includingthese:
" The outermost containment isolation valve in system piping which penetratesprimary reactor containment.
" The second of two valves normally closed during ncrmal reactor operation insystem piping which does not penetrate pnma'r reactfr', containment.
" The RCS safety and relief valves.
Section 3.9 presents the design transienisf loading co'mbinations, stress limits, andevaluation methods used in the design ar•iakses of :RCPB components and supports todemonstrate that RCPB integrity is maintained(-J.
Compliance with Codes and Co•de eCases
Compliance with 10 CFR 50.55a
The RCPB componaents are designed and fabricated as Class 1 components inaccordance with Section :II of the ASME Boiler and Pressure Vessel Code(Referencc 1),except forco•mponent .s that meet the exclusion requirements of 10 CFR50.55a(c) which art designed and fabricated as Class 2 components. The RCPBcoqpi(nen classification complies with the requirements of GDC 1 and 10 CFR50.• 5 5a. Table 3 2.2 1• I-Classification Summary lists the RCPB components, including
pipressure vessels. piping,'ý pumps, and valves, along with the applicable componentcodes Other saPty-related plant components are classified in accordance with RGI-16,as specifiýd in Section 3.2.
The co•d• of record for the design of the U.S. EPR is the 2004 edition of the ASMEBoiler and Pressure Vessel Code (no addenda).
The application of Section XI of the 2004 edition of the ASME Boiler and PressureVessel Code to the U. S. EPR is described in Section 5.2.4 and Section 6.6 Theapplication of the ASME Code for Operation and Maintenance of Nuclear PowerPlants (OM Code) (Reference 2) is described in Section 3.9.6.
Compliance with Applicable Code Cases
104.05.01-7
5.2.1.2
I ASME Section III Code Cases acceptable for use in the U.S. EPR desig , subject to thelimitations specified in 10 CFR 50.55a, are listed in RG 1.84. Code Cases pertaining to
Tier 2 Revision 2-Interim Page 5.2-1Tier 2 Revision 2-Interim Page 5.2-1
A0%02ft*.,
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
104.0 .01-ASME Section III, Division 2 are addressed in Section 3.8. Table 5.2 1 ASME Code
Cases lists the specific Code Cases used int the U.S. EPR designi. A COL applicant that
to be used. Cede Caesprang to ASMIE Cede Section 111, Divisiont 2 are addressedin Seetienf3.8.ASME Section XI Code Cases acceptable for use for preservice inspection
and inservice inspection (ISI), subject to the limitations specified in 10 CFR 50.55a, are
listed in RG 1.147 and described in Section 5.2.4 and Section 6.6. ASME OM Code
Cases acceptable for use for preservice testing and inservice testing (IST), subject to the
limitations specified in 10 CFR 50.55a, are listed in RG 1.192 and described in
Section 3.9.6.
Table 5.2-1-ASME Code Cases lists the specific Code&Cases used in the U.S. EPR
design. A COL applicant that references the U.S. EPR designcertification will identify
additional ASME Code Cases to be used.
I
5.2.2
5.2.2.1
Overpressure Protection
Pressurizer safety relief valves (PSRV) protect the RCPB from overpressure during
power operation and during low temperature Operation. Auxiliary and emergencysystems connected to the RCS aie not utilized forRCPB overpressure protection.
Main steam safety valves (MSSV) and maini steam relief trains protect the secondary
side of the steam generators from ove'ressure. Secondary side overpressureprotection is add ress2 in ':Section 1•i0.3.
Design Base's
Component designgbases for the PSRVs and the secondary side overpressure protection
devices are addre'ssed in Section 5.4.13 and Section 10.3, respectively.
The PSRVs are part of tl~e RCPB and are designed to meet the requirements for ASME
Section III, Class I components (GDC 1, GDC 30, 10 CFR 50.55a). Component
classifications are presented in Section 3.2.
The opýeýnn set pressures and capacity of the PSRVs are sufficient to limit the RCS
pressure to less than 110 percent of the RCPB design pressure during any condition of
normal operation, including anticipated operational occurrences (AOO) (GDC 15).
The bounding design transient for RCPB overpressure is a turbine trip at full power.
This transient bounds all upset, emergency and faulted conditions identified in
Section 3.9.1.
The PSRVs maintain the RCS pressure below brittle fracture limits when the RCPB is
stressed under operating, maintenance, testing, and postulated accident conditions,
including low temperature operation, so that the RCPB behaves in a non-brittle
manner and the probability of rapidly propagating fracture is minimized (GDC 31).
Tier 2 Revision 2-Interim Page 5.2-2
0U.S. EPR FINAL SAFETY ANALYSIS REPORT
NiCrFe Alloy 600 base metal or Alloys 82/182 weld metal is not used in RCPB
applications. NiCrFe Alloy 690 base metal has controlled chemistry, mechanicalproperties, and thermo-mechanical processing requirements that produce an optimum
microstructure for resistance to intergranular corrosion. Alloy 690 is solutionannealed and thermally treated to optimize the resistance to intergranular corrosion.
Alloy 690 and its weld filler metals (Alloy 52/52M/152) in contact with RCS primarycoolant have limited cobalt content not exceeding 0.05 wt%. Alloy 690 in contact
104.05.01-7 %with RCS primary coolant has limited sulfur content not exceeding 0.02 wt%.
Code Case N-785 has been applied to CRDM materials as shown in Table 5.2-2. Thiscode case was approved by the ASME Boiler and Pressure Vessel Standards Committeeon October 12, 2009. The basis for approval of thijjse is derived from the fact thatthe chemical composition, material propertiesand heat treatment requirements forSA-182/182M Grade F6NM and SA-479/479M (TUNS $41500) arevirtually identical.
5.2.3.2 Compatibility with Reactor Coolant
5.2.3.2.1 Reactor Coolant Chemistry
The RCS water chemistry is controlled to minimize negative impacts of chemistry onmaterials integrity, fuel rod corrosion, fuel design performance, and radiation fields,
and is routinely analyzed for verificati6o. The w*a•ter chemistry parameters are basedon industry knowledge and indust experience as summarized in the EPRI PWRPrimary Water Chemistry Guideliies (Reference 3).
The chemical and vol ue contrl system (CVCS) provides the primary means for
maintaining the required volume of water in the RCS and for the addition ofchemicals. The design of the CVCS allows for the addition of chemicals to the RCS to
control pH, scavenge oxygen, control radiolysis reactions, and .maintain corrosionproduct particulates within a specified range. Table 5.2-3-Reactor Coolant WaterChemistry - Control Parameters shows the control values for the reactor coolant
chemistry parameters and impurity limitations during power operation. These criteria
conform to the recommendations of RG 1.44 and the EPRI PWR Primary Water
Chemistry Guidelines report.
Enriched boric acid (EBA) is added to the RCS as a soluble neutron poison for core
reactivity control. Lithium hydroxide enriched in lithium 7 is used as a pH control
agent to maintain a slightly basic pH at operating conditions. This chemical is chosenfor its compatibility with the materials and water chemistry of borated water/stainlesssteel/zirconium/nickel-base alloy systems. Lithium-7 is also produced in solution from
the neutron irradiation of the dissolved boron in the coolant.
In addition to degasification during startup, two chemicals are added to the reactor
coolant to control oxygen: (1) hydrazine during startup operations below 250'F; and
Tier 2 Revision 2-Interim Page 5.2-9Tier 2 Revision 2-Interim Page 5.2-9
1ý
EFU.S. EPR FINAL SAFETY ANALYSIS REPORT
Table 5.2-1-ASME Code Cases
Code Case Number TitleN-60-5 Material for Core Support Structures Section III,
Division 1N-71-18 Additional Materials for Subsection NF, Class 1, 2,
3, and MC Supports Fabricated by Welding,Section III, Division 1
N-284-1 Metal Containment Shell Buckling DesignMethods, Section III, Division 1, Class MC
N-319-3 Alternate Procedure f6r 'Evaluation of Stresses inButt Welding Elbows in Class 1 Piping, SectionIII, Division 1
Alternative Examination Requirements for PWRReactor Ve'sesel Upper Heads with Nozzles HavingPressur-Retaining, Partial-Penetration WeldsI
I TTP'i~~f'OA-479/qSA-479M TTNVS S41,;nn fhr CIA-,- 1111výý1 IA- Constrction Section III Dihh~rin I
OMN-1, Revision 0 2 AlteriativeRules for Preservice and InserviceTesting of Active Electric Motor-Operated ValveAssemblies fin Light-Water Reactor Power Plants
OMN-13, Revision 0 2, Requirements f•r Extending Snubber InserviceVisual Exanination Interval at LWR PowerPlants
NOTES:
1. See Section 3.8 for use.
2. See Section 3.9.6 for use.
104.05.01-7ý 3. See Sectioni5.2.3.1 for use.
Tier 2 Revision 2-Interim Page 5.2-36Tier 2 Revision 2-Interim Page 5.2-36
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
I
Table 5.2-2-Material Specifications for RCPB Components
Sheet 4 of 5
Component Material
ASME SA-479 UNS S41500 (Code Case N-785)SA-18GdLatch housing 04.05.01-7 > F6NM (see Note 1) -8N)SS4A52r)
Seamless tube ASME SA-312 Grade TP347 (Seamless) (see Note 3)
Bolt ASME SA-453 Grade 660 (see Note 7)
Nut ASME SA-437 Grade B4C (see Note 1)
Welding filler material SFA 5.4 E347SFA 5.9 ER347SFA 5.14 ERNiCrFe-7SFA 5.14 ERNiCrFe-7A
RCP13 ValvesProccuriZc safety Relief 4VAnl':
BodiesA vender for the PSRV has SA-182 Grade F304.(ýee Notes 3 & 4), Grade F304L (see Note 3),not been chesen for the U.S. EPR Grade F304LN (se6 Note 3). Grade F316 (see Nbtes 3 & 4), Grade
F316L (see Note 3 C, Grade F316LN (see Note 3)
SA-351 Grade CF3, GadO'CF3A, Grade CF3M, Grade CF8 (seeNote 4),I'Grade CF8A (see Note 4), Grade CF8M (see Note 4 & 10)
Bonnets SA-182 Grade•F304 (see Notes 3 & 4), Grade F304L (see Note 3),Grade F304LN (see Note 3•), Grade F316 (see Notes 3 & 4), GradeF316L (see Note 3). Grade]'F316LN (see Note 3)
SA-351 Grade CF3. Grade CF3A, Grade CF3M, Grade CF8 (seeNote 4), Grade CF8A (see Note 4), Grade CF8M (see Note 4 & 10).SA240 Type 304 (see Notes 3 & 4). Type 304L (see Note 3), Type
304LN (see Note 3), Type 316 (see Notes 3 & 4), Type 316L (seeNote 3), 316LN (see Note 3)
Discs SA-182 Grade F304 (see Notes 3 & 4), Grade F304L (see Note 3),Grade F304LN (see Note 3), Grade F316 (see Notes 3 & 4), GradeF316L (see Note 3), Grade F316LN (see Note 3)
SA-351 Grade CF3, Grade CF3A, Grade CF3M, Grade CF8 (see.Note 4), Grade CF8A (see Note 4), Grade CF8M (see Note 4 & 10)
SA-479 Type 304 (see Notes 3 & 4), Type 304L (see Note 3), Type304LN (see Note 3), Type 316 (see Notes 3 & 4), Type 316L (seeNote 3), 316LN (see Note 3), XM-19 (see Note 3)
SA-564 Type 630 (Conditions H1075, Hl100, H1150)
SB-637 UNS N07718 (see Note 8)
Stems SA-479 Type 304 (see Notes 3 & 4), Type 304L (see Note 3), Type304LN (see Note 3), Type 316 (see Notes 3 & 4), Type 316L (seeNote 3). Type 316LN (see Note 3), Type XM-19 (see Notes 3 & 9)
SA-564 Type 630
SB-637 UNS N07718 (see Note 8)
Tier 2 Revision 2-Interim Page 5.2-40
Response to
Request for Additional Information No. 344(4062), Supplement I
02/23/2010
U.S. EPR Standard Design CertificationAREVA NP Inc.
Docket No. 52-020SRP Section: 04.03 - Nuclear Design7
Application Section: 04.03
QUESTIONS for Reactor System, Nuclear Performance and Code Review (SRSB)
K4
* V &
'1
V \/ /
N
AREVA NP Inc.
Response to Request for Additional Information No. 344, Supplement 1U.S. EPR Design Certification Application Page 2 of 3
Question 04.03-27:
OPEN ITEM
The staff requests that a combined license (COL) information item to be added to Table 1.8-2 ofthe FSAR in regard to collection of plant specific surveillance capsule data to be used tobenchmark BAW-2241 PA's applicability to the specific plant.
The capsule withdrawal and reporting requirements will follow 10 CFR Part 50 Appendix H.
Response to Question 04.03-27:
U.S. EPR FSAR Tier 2, Table 1.8-2 will be revised to include a COL Item for U.S. EPR FSARTier 2, Section 5.3.1.6.2, Plant Specific Monitoring. U.S. EPR TSAR Ti6,2, Section 5.3.1.6.2 willbe revised to state that a COL applicant that references the U.S. EPR design certification willprovide plant-specific surveillance capsule data to benchmark BAW-2241PA "and demonstrateapplicability to the specific plant. K>
FSAR Impact:
The U.S. EPR FSAR Tier 2, Table 1.8-2 and Section 5.3.1.6.2 will be revised as described inthe response and indicated on the enclosed markup.
AREVA NP Inc.
Response to Request for Additional Information No. 344, Supplement IU.S. EPR Design Certification Application Page 3 of 3
Question 04.03-28:
OPEN ITEM
Throughout the U.S. EPR Final Safety Analysis Report (FSAR) Tier 2, Section 4.3, AREVANP refers to licensing topical report ANP-10286P, "U.S. EPR Rod Ejection AccidentMethodology Topical Report." This document is currently under review by the NRC staff. ThisRAI is created to track an open item associated with this review. It will be closed uponcompletion of the review by the NRC staff. AREVA is requested to acknowledge receipt of thisopen item. ,4•
Response to Question 04.03-28: .
AREVA NP acknowledges receipt of this open item.
FSAR Impact:
The U.S. EPR FSAR will not be changed as a result of this question.
NN, 2
-L
UEs. EPR Final SafetyAnalysis Report Markups
/
/
~ V\
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
Table 1.8-2-U.S. EPR Combined License Information ItemsSheet 24 of 49
AeeR- AetNeReq~ied Req~iedby GOL- by GOL-
Item No. Description Section App^iea4 "•-e
5.2-2 A COL applicant that references the U.S. EPR 5.2.1.2 ydesign certification will identify additionalASME code cases to be used.
5.2-3 A COL applicant that references the U.S. EPR 5.2.4 ydesign certification will identify theimplementation milestones for the site-specificASME Section XI preservice and inserviceinspection program for the reactor coolantpressure boundary, consistent with therequirements of 10 CFR 50.55a (g). The program,,will identify the applicable edition and addenda.of the ASME Code Section XI, and will ide'nti•fadditional relief requests and alternatives to "tCode requirements.
5.3-1 A COL applicant that references the7 U.S: EPR 5 3.1.6 ydesign certification will identify the ,implementation milestones for the mhaterial"surveillance program.
5.3-2 A COL applicant that referenc es the UlS.SEPR 5.3.2.1 ¥design certificatin will provide a plantfsjecificpressure and teimperature 'li- ts report- (PTLR),consistent with anapproved metniod'l1gy.
5.3-3 A COL appic"nt that references the U.S. EPR 5.3.2.3 Y_de-i gncertiflcationh.wIll provi de plant-specificP I svalues in accirdance with 10 CFR 50.61 04.03-271for ,essel beltline m aterials.
5.3-4 A COQL pplicant that references the U.S. EPR 5.3.1.6.2design 'ert ficatilOn'wfii provide plant-specificsurveillance datla to benchmark BAW-2241 P-Aand demonstriate applicability to the specifico1ant.
5.4-1 A COL applicant that references the U.S. EPR 5.4.2.5.2.2 ydesign certification will identify the edition andaddenda of ASME Section XI applicable to thesite specific Steam Generator inspectionprogram.
Tier 2 Revision 2-Interim Page 1.8-29Tier 2 Revision 2-Interim Page 1.8-29
U.S. EPR FINAL SAFETY ANALYSIS REPORT
specimens; i.e. major axis of the specimen is parallel to the surface and normal to the
major working direction (the transverse direction). The CT specimens and Charpy V-
notch specimens from the weld metal are oriented so that the major axis of the
specimen (axis normal to the crack plane for CT specimens) is parallel to the RV insidesurface and normal to the weld bead direction. Weld metal tension specimens are
oriented in the same direction as the Charpy V-notch specimens with the gage length
consisting entirely of weld metal (the transverse direction). The Charpy V-notch
specimens from the HAZ are oriented so that the major axis of the specimen is parallel
to the RPV inside surface and normal to the weld bead direction. The Charpy V-notch
root is in the HAZ about 1/32 inch from the fusion line.
5.3.1.6.1 Fluence Monitoring
The neutron fluence on the vessel material testspfecimens and the vessel itself is
determined based on core-follow calculations of the cycle-by-cycde operation. The
fluence and uncertainty methodologies,,,esc'ribed in BAW-2241P2A,, "Fluence and
Uncertainty Methodologies" (Reference 9), explainw.how the calculations are
performed. The calculations conform to RG 1 A90 and thus meet the requirements of
10 CFR Part 50, Appendix H. " N
As noted in RG 1. 190, the bases for the biaas and random uncertainties in the
calculations are: .- •
" Database of ds6imetry measurements.
* Benchmark database comparing calculations to measurements.
" Sensitivity evaluation with fabrication and operational tolerances.
5.3.1.6.2 Planht specific Monitoring
The uncertainty evaluations noted in BAW-2241P-A provide calculations, with well-
,dffined uncertainties, for RPV fluence in operating light water reactors. While it is[04 .3 -2 • ':•!" " ..
[04.03-27 expcted thatthbe calculations for the U.S. EPR will have similar accuracy and random
uncrtainties, measured data from the material surveillance program will supplement
the calcdlated predictions. A COL applicant that references the U.S. EPR design
certification will provide plant-specific surveillance capsule data to benchmark BAW-
2241P-A and demonstrate applicability to the specific plant. The capsule withdrawal
and reporting requirements will follow 10 CFR Part 50, Appendix H. Therecommended withdrawal schedule is outlined in.Table 5.3-6-Surveillance Specimen
Withdrawal Schedule Per ASTM E185-82.
Calculations are used to estimate the initial fluence to the vessel materials. Once
operation has commenced, plant specific dosimetry measurements are evaluated to
demonstrate that fluence uncertainties are consistent with historical data. Showing
Tier 2 Revision 2-Interim Page 5.3-6
Responseto
Request for Additional Information No. 367
3/11/2010
U.S. EPR Standard Design CertificationAREVA NP Inc.
Docket No. 52-020SRP Section: 04.06 - Functional Design of Control Rod Drive System
Application Section: 04.06
QUESTIONS for Reactor System, Nuclear Performance and Code Review (SRSB)
AREVA NP Inc.
Response to Request for Additional Information No. 367U.S. EPR Design Certification Application Page 2 of 4
Question 04.06-14:
OPEN ITEM:
In general terms of the U.S. EPR Tier 2 FSAR Subsections 4.4.2.9.5, 4.4.4.3, 4.4.4.5.3,4.4.4.5.4, 4.4.6.1,4.4.6.4, and 4.4.6.5, the applicant provides a brief description of the fixed in-core SPND neutron flux measurements in relationship to the two types of in-core trips withregard to uncertainties in the calculations, influence of power distributions, high linear powerdensity functions, low DNBR I&C functions, and analysis of steady and transient conditions. Inthese subsections, the applicant refers to the topical report ANP-10287P, "In-core Trip Setpointand Transient Methodology for the U.S. EPR Topical Report" for a more detail discussion.
However, after review of these subsections and the topical repo rt, th staff has determined thatmore information is necessary to determine how the methods descriled in ANP-1 0287P will beimplemented and verified in regard to instrumentation and control systemni§.
Therefore, the staff requests that the applicant provide a description on how the "methodologiescontained in ANP-1 0287P will be implemented and verified for the U.S. EPR design relating toinstrumentation and control systems. In particular, define what will be checked and verified byCOL applicants prior to the first cycle core loading and as part of reload analysis to satisfy thefollowing approval limitations stated in the SE for ANP-10287P:
1. LIMITATION NO. 1- MIXED CORES
Section 4.8 contains an evaluation of the applicability of the U.S. EPR setpoint methodology tomixed core configurations. The following limitation applies to the application of ANP-10287P,Revision 0: ,4,
The setpoint methodology documented In' i-ANP-1 0287P, Revision 0 [1] is only acceptable tocores that consist entirely of hyd~raulically comnatible fuel assemblies, i.e, a single package ofassembly specific CR Hricorrelation.
2. LIMITATION NO. 2-CYCLE SPECIFIC UNCERTAINTY VALUES
Since the actualkuncertainties and setpoint values are not part of this review and are notavailable to the stiff, any transient analyses taking credit for the in-core setpoint system canonly be approved when actual values of these uncertainties and setpoints are conservativelyapplied following this methodology, or it has been demonstrated that the uncertainties can beconservatively bounded. The following limitation applies to the application of ANP-10287P,Revision 0:
Applications of the setpoint methodology documented in ANP-10287P, Revision 0 [1] mustinclude a review of the applicable uncertainty values used to generate the setpoint values usedin the analyses.
3. APPLICATION SPECIFIC ITEM PRIOR TO THE FIRST CYCLE OPERATION
The methodology to confirm that the static setpoint values provide adequate protection duringtransient events described in Section 9 of Topical Report ANP-10287P depends on identifyingand characterizing the limiting transient. The limiting transient is defined as the event that
AREVA NP Inc.
Response to Request for Additional Information No. 367U.S. EPR Design Certification Application Page 3 of 4
results in the minimum difference between uncompensated DNBR and LPD results and theSAFDLs. The following limitation applies to the application of ANP-10287P, Revision 0:
Prior to the first cycle operation, confirmatory evaluation has to be performed for every AOOusing the procedure described in Section 9 of Topical Report ANP-1 0287P to identify thelimiting transient of the plant as built. Based on the confirmatory evaluation results, analyseshave to be performed for AQOs that have significant differences between the assumed inputconditions and the as-built conditions, if the differences can not be conservatively bounded bythe assumed uncertainty values. For the most limiting transient that relies on in-core trip forprotection, the applicant shall provide for staff review the analysis results demonstrating that theuncompensated DNBR and LPD satisfies SAFDL with a 95/95 assurance.
4. APPLICATION SPECIFIC ITEM FOR RELOAD ANALYSIS
The methodology described in Section 9 of Topical ReporttANP-10287Pis vague on whichtransient events are used to confirm that the static setpofi~t"values provide dbequate protectionduring transient events. Therefore, the following limitati6n applies to the application of ANP-10287P, Revision 0:
During reload analysis, it has to be confirmed and appropriately documented using themethodology described in Section 9 of ANP-1 0287P that the static setpoint value providesadequate protection for at least the three rmost:limiting AOOs identified by Item 3 above.
Response to Question 04.06-14
It is anticipated that the NRCsafety evaluation for the AREVA NP Topical Report ANP-10287Pwill include the limitations specified in this question. Because these will be limitations on theapproved methodology defined in the topical report the plant and cycle specific implementationof the methodology, whether performed byIýREVA. NP Inc. (AREVA NP) or a COL applicant,must satisfy the approved methodology. AREVA NP considers that the approved methodologyconsists of details Uflhed in the body of the topical report, RAI responses incorporated into theapproved version of thelfeport, and limitations defined in the NRC safety evaluation.
Therefore the6 implementatioi of this methodology will require that the following be verified withrespect to the limiiitations define.d in the NRC safety evaluation.
1. Characteristics of thebfuel assemblies will be examined to verify that they are all hydraulicallycompatible based on the criterion that a single package of assembly specific critical heat flux(CHF) correlations can be used to evaluate the assembly performance.
2. Uncertainties used in the setpoint analyses will be verified to be appropriate for the plantand cycle being analyzed.
3. A COL applicant that references the U.S. EPR design certification will provide for staffreview, prior to the first cycle of operation, analysis results demonstrating that theuncompensated departure from nucleate boiling ratio (DNBR) and linear power density(LPD) satisfies the specified acceptable fuel design limits (SAFDL) with a 95/95 assurance.
4. Current analysis results will be reviewed for subsequent cycles to confirm that the staticsetpoint value provides adequate protection for at least the three limiting anticipated
AREVA NP Inc.
Response to Request for Additional Information No. 367U.S. EPR Design Certification Application Page 4 of 4-
operational occurrences (AOO). This review will be documented in the quality assurancerecords.
Table 1.8-2 of the U.S. EPR FSAR Tier 2 will be revised to include a COL item in Section15.0.0.3.9. Section 15.0.0.3.9 will be revised to state that a COL applicant that references theU.S. EPR design certification will provide for staff review, prior to the first cycle of operation,analysis results demonstrating that the uncompensated departure from nucleate boiling ratio(DNBR) and linear power density (LPD) satisfies the specified acceptable fuel design limits(SAFDL) with a 95/95 assurance.
FSAR Impact:
U.S. EPR FSAR Tier 2, Table 1.8-2 and U.S. EPR FSAR Tier 2-5Sdtion 15.0.0.3.9 will berevised as described in the response and indicated on the enclosed miarkup.
.. . •1i~i
U.S. EPR Final SafetyAnalysis Report Markups
EP55: U.S. EPR FINAL SAFETY ANALYSIS REPORT
Table 1.8-2-U.S. EPR Combined License Information ItemsSheet 44 of 49
At4rq- Antmoa-Req~ied Req~iedby-GQ6 by-GO-
Item No. Description Section AppI4Gaf :-I-, 4eId
14.2-12 A COL applicant that references the U.S. EPR 14.2.12design certification will provide site-specific testabstract information for plant laboratoryequipment.
14.3-1 A COL applicant that references the U.S. EPR 14.3 ydesign certification will provide ITAAC foremergency planning, physical security, and site-specific portions of the facility that are notincluded in the Tier 1 ITAAC associated withthe certified design (10 CFR 52.80(a)).
14.3-2 A COL applicant that references the U.S. P1RII 1"4.3 13design certification will describe the selectionmethodology for site-specific SSC to be included ;in ITAAC, if the selection methodology isdifferent from the methodology des.ribedwithin the FSAR, and will also provide t•e•iselection methodology associated withemergency planning an diphysical securi thardware.
14.3-3 A COL applicant ihat rfercnc'es theU S EPR 14.3design certificatinh will identify•,plan forimplementing D Ti-. lheplan will aidntify 1)the evaluations that Willbe performed for DAC,2) the schedidle .f6r perfi iing these evaluations,andl3) the assocaia~ Jdesiffnprocesses andii6rmation that w~i1be available to the NRC foraufdit. .. i
15.0-1 A COL ap~plicant that references the U.S. EPR 15.0.0.3.9design ce'itifation will provide for staff review,prior to the f i-s• cycle of operation, the analysisresults demonstrating that the uncompensatedDNBR and LPD satisfies the SAFDL with a 95/95assurance in accordance with ANP-10287P.
Tier 2 Revision 2-Interim Page 1.8-49
EPRU.S. EPR FINAL SAFETY ANALYSIS REPORT
" Spectrum of Rod Ejection Accidents.
" Loss-of-Coolant Accidents Resulting from Spectrum of Postulated Piping Breakswithin the Reactor Coolant Pressure Boundary.
Transient Analysis with Incore Trips
The transient analysis is performed with incore trip models decoupled from the system
simulation code, S-RELAP5. The incore trip models are generically referred to as the"algorithm" or separately as the Low DNB Channel algorithm and High LPD Channelalgorithm. The core boundary conditions for the algorithm are generated in S-RELAP5 and power distributions are generated in the no~da neutronics code, PRISM.
The Low DNB Channel and High LPD Channel alg)rItT1mS are simulated to predicttimes at which the incore trip setpoints are reached, and to6!nonstrate the adequacy
of the dynamic compensation on the trips. Table 15.0-7 lists thlenicore trip setpointsused in the accident analyses. The methodology for confirming teiildynamic
compensation is described in Section 9.4•of Reference 2.
The Low DNB Channel and High LPD ChaTn1el algorithms use the followingmeasurements:
" The reactor power distribuions de(w eJfi\ Im the SPNDs, which are part of thenuclear incore instrumentah I o "1.
" The prinmarl systemL pressure denved from the primary pressure sensors.
" The core flow de ri ved frOint 1theactor coolant pump (RCP) speed sensors and thecalibrated voumetric flowfirom a surveillance measurement.
104.06-14'The'e:actor inlet,:teomperature derived from the cold_-leg temperature sensors.
e A COL appliant that references the U.S. EPR design certification will provide forstaff review, prior to the first cycle of operation, the analysis results demonstratingthat the uncompensated DNBR and LPD satisfies the SAFDL with a 95/95assurancein accordance with ANP-10287P.
5.0.0.3.10 Plant Design Changes
The information presented in Section 15.0 represents the current U.S. EPR design.
Some of the analyses presented in this section used slightly different values. In thesecases the differences have been evaluated and found to have a negligible orconservative impact on the results and conclusions.
II1I
15.0.1 Radiological Consequence Analysis
This section is not applicable to new plants. The radiological consequences analyses
are addressed in Section 15.0.3.
Tier 2 Revision 2-Interim Page 15.0-15Tier 2 Revision 2-Interim Page 15.0-15
Response to
Request for Additional Information No. 366, Supplement 1
2/17/2010
U.S. EPR Standard Design CertificationAREVA NP Inc.
Docket No. 52-02004.06 - Functional Design of Control Rod Drive System
Application Section: 04.06.:SRP Section:
QUESTIONS for Reactor System, Nuclear Performiance and Code Review (SRSB)
AREVA NP Inc.
Response to Request for Additional Information No. 366, Supplement 1U.S. EPR Design Certification Application Page 2 of 2
Question 04.06-13:
OPEN ITEM:
FSAR Tier 2, Section 4.6.4 states that in the safety analyses in FSAR Tier 2, Chapter 15, exceptfor the large break loss of coolant accident, no credit is taken for reactivity control systems otherthan reactor trip to mitigate the events to achieve a stable plant condition. The staff notes thatin FSAR Tier 2, Section 15.1.5 appears to indicate that boron addition via the SIS is credited tomitigate large steam line breaks from hot zero power conditions. Please clarify this apparentdiscrepancy.
Response to Question 04.06-13:
U.S. EPR FSAR Tier 2, Table 15.1-15, indicates that medium head safety injection (MHSI) isactuated for the most limiting main steam line break (MSLB) event. Although boron tracking isactivated in the S-RELAP5 analysis of this event, the reactivity contribution Of the boron (shownin U.S. EPR FSAR Tier 2, Figure 15.1-54) is not necessary for the event mitigation. U.S. EPRFSAR Tier 2, Table 15.1-15 shows that the peak return to power for the limiting MSLB eventoccurs at 273.2 seconds with a value of approximateiy,23 percent of rated power (see U.S. EPRFSAR Tier 2, Figure 15.1-55). However, borated MHSI fluid does not begin entering the reactorcoolant system (RCS) until after 720 seconds (see U.S. EPR FSAR Tier 2, Table 15.1-15), wellbeyond the return to power peak. At this point in the transient, reactor power is approximately 3percent of rated power (see U.S. EPR FSAR Tier 2, Figure 15.1-55). The power excursion iscaused by moderator reactivity feedback resulting from the reduction incore inlet temperaturedue to secondary side overcooling. The power excursion is terminated when the affected steamgenerator dries out (see U.S.BEPR FSAR Tier 2, Figure 15.1-49) and significant primary-to-secondary heat transfer ceases (see U.S. EPR FSAR Tier 2, Figure 15.1-48).
Boration resulting from MHSI actuation does not contributeto the mitigation of this event andthe statement in U.S. EPR FSAR Tier 2, Section 4.6.4 is accurate.
FSAR Impact:
The U.S. EPR FSAR will not be changed as a result of this question.