Upload
doris-parks
View
224
Download
1
Tags:
Embed Size (px)
Citation preview
Preparing Solutions
Standard SolutionsSolutions can be prepared two ways:
i) solids added to liquids OR
ii) liquids added to liquids.
Standard Solution: A solution for which the precise concentration is known. (Prepared in labs and industry.)
We will be preparing a standard solution by accurately massing a solute then carefully and gradually adding a precise amount of water.
Solution Preparation
Stock Solution: a solution, usually concentrated or saturated, that is in stock or on the shelf and available for use.
Dilution: the process of decreasing the concentration of a solution, usually by adding more solvent.
We will be preparing a standard solution by accurately measuring a volume of stock or standard solution then carefully and gradually adding a precise amount of water.
Required Equipment:• Volumetric flask – comes in
different sizes and has one precise marking, unlike an Erlenmeyer flask that has approximate volume markings.
• Precise electronic balance – to mass the solid that will be put into a volumetric flask to make a standard solution
• Pipette – for adding a very accurate amount of stock solution to a volumetric flask and then diluting the initial solution to get a new standard
solution.
PipettesPipettes
Preparing a Standard Solution - Technique
1) Mass the solute on wax weighing paper, or plastic container & place the solute in a VERY CLEAN beaker
2) Rinse off the weighing paper or plastic container with distilled water to ensure all the massed solute molecules end up in the beaker
3) Add some distilled water & stir the soluteMAKE SURE all the solute is DISSOLVED!
4) Once dissolved transfer the solution into a
volumetric flask using a funnel and ENSURE
NOT A DROP is spilled or lost
5) Rinse out the beaker 3 times with distilled
water starting from the top and transfer
the wash into volumetric flask
Technique
6) Rinse out the funnel & rinse off the tip when removed7) Add distilled water until 2-3 centimeters BELOW the mark, put a stopper on & invert the flask several times to mix it well
8) Looking at the line on the volumetric flask at eye level, add the distilled water DROP by DROP up to the line until the bottom of the meniscus is sitting on the line.
You can use a dropper or small pipette to do this.9) The solution must be stored with a stopper to avoid impurities.
BEFORE using the solution, it will need to be shaken or inverted several times to ensure all the solute is dissolved since it has been sitting still for a while.
http://www.youtube.com/watch?v=cckAwavEKA0
Calculations Starting with MassWhat is the mass of NaOH pellets needed to
make 750 mL of a 3.00 M solution?
Given:
V = 750 mL = 0.750 L
M or c = 3.00 M = 3.00 mol/L
1st find n = ? n = c x V (or M x V)
2nd find m = ?
Calculations Starting with MassWhat is the mass of NaOH pellets needed to
make 750 mL of a 3.00 M solution?
Given:
V = 750 mL = 0.750 L
M or c = 3.00 M = 3.00 mol/L
1st find n = ? n = c x V (or M x V)
2nd find m = ? m = n x Molar mass
n = c x V = # mol
n = 3.00 mol/L x 0.750 L = 2.25 mol
m = 2.25 mol x 40.0 g/mol = 90.0 g
Dilution CalculationsDilution CalculationsWhen determining the volume needed of a
stock solution to make a new solution, just remember that original volume of solution has the same number of moles as the final solution, only added H2O…
moles solute BEFORE = moles solute AFTER the dilution the dilution
n before = n after
Dilution CalculationsDilution Calculations
moles solute BEFORE = moles solute AFTER
the dilution the dilution
n before = n after
C1 x V1 = C2 x V2 OR
Mi x Vi = Mf x Vf
n = C x V
n = M x V
Dilution Calculations: Example Water is added to 0.200 L (Vi ) of a 2.40 mol/L
(Mi) NH3(aq) cleaning solution, until the final volume is 1.000 L (Vf). Find the molar concentration of the final, diluted solution.
Dilution Calculations: ExampleWater is added to 0.200 L (Vi ) of a 2.40 mol/L (Mi)
NH3(aq) cleaning solution, until the final volume is 1.000 L (Vf). Find the molar concentration of the final, diluted solution. n before = n after
Ci x Vi = Cf x Vf OR
Mi x Vi = Mf x Vf
2.40 mol/L x 0.200 L = Mf x 1.000 L
Mf = 2.40 mol/L x 0.200 L
1.000 L
Mf = 0.480 mol/L
Only one
equation
needed
Dilution Calculations: Example
Water is added to 0.200 L (Vi ) of a 2.40 mol/L (Mi) NH3(aq) cleaning solution, until the final volume is 1.000 L (Vf). Find the molar concentration of the final, diluted solution.
NEED: Mf = ?
Mi x Vi = Mf x Vf
Mf = Mi x Vi
Vf
Mf = 2.40 mol/L x 0.200 L
1.000 L
Mf = 0.480 mol/L
Preparing a Standard Solution by Dilution
1) Using calculations, determine the amount of stock solution required to make the new solution and choose an appropriately-sized pipette.
Example, the stock solution is 2.00 mol/L and the diluted solution needs to be 0.040 mol/L in a
1.00 L volumetric flask. Vi = Mf x Vf Mi
= 0.040 M x 1.00 L 2.00 M
= 0.020 L (20 mL)
2) Choose a 20 mL pipette or a graduated pipette that holds 20 mL of solution
Preparing a Standard Solution by Dilution3) Using the bulb, fill the pipette with solution a few
centimeters above the marked amount. Quickly replace the bulb with your thumb4) Carefully, slide or loosen your thumb until you
see the level of the solution lowering at a slow rate. Stop at the marked line.
You may have to try a few times since using a bulb and pipette effectively takes practice.
5) Once the bottom of the meniscus is at the line, press firmly with your thumb to hold that level and carry the pipette to the volumetric flask. Release the solution into the flask.
6) Fill the volumetric flask carefully as explained in technique section of preparing a Standard Solution from Mass
http://www.youtube.com/watch?v=3EOiCrtvUUM
HOMEWORK
• Read page 300-307
• pg 302 # 1,2,4,5a
• pg 306 # 6-8
• pg 306-307 Questions # 2 – 5, 8 (skip d :)
• READ OVER Activity 6.5.1 pg 301 &
Activity 6.5.2 pg 305