PREPARED BY PREPARED BY V.SANDHIYAV.SANDHIYA

LECT/ ECELECT/ ECE

UNIT- 3

APPLICATIONS OF OP-AMP

1

2

Analog to Digital ConversionAnalog to Digital Conversion

ADC EssentialsADC Essentials

A/D Conversion TechniquesA/D Conversion Techniques

Interfacing the ADC to the IBM PCInterfacing the ADC to the IBM PC

DAS (Data Acquisition Systems)DAS (Data Acquisition Systems)

How to select and use an ADCHow to select and use an ADC

A low cost DAS for the IBM PCA low cost DAS for the IBM PC

3

Why ADC ?Why ADC ?

Digital Signal Processing is more popular Easy to implement, modify, … Low cost

Data from real world are typically Analog Needs conversion system

from raw measurements to digital data Consists of

Amplifier, Filters Sample and Hold Circuit, Multiplexer ADC

4

ADC EssentialsADC Essentials

Basic I/O Relationship ADC is Rationing

System x = Analog input /

Reference• Fraction: 0 ~ 1

n bits ADC Number of discrete output

level : 2n

Quantum LSB size Q = LSB = FS / 2n

Quantization Error 1/2 LSB Reduced by increasing n

5

Analog Input SignalAnalog Input Signal

Typically, Differential or Single-ended input signal of a single polarity

Typical Input Range 0 ~ 10V and 0 ~ 5V

If Actual input signal does not span Full Input range

Some of the converter output code never used

Waste of converter dynamic range

Greater relative effects of the converter errors on output

Matching input signal and input range Prescaling input signal

using OP Amp In a final stage of

preconditioning circuit By proportionally

scaling down the reference signal

If reference signal is adjustable

6

Converting bipolar to unipolarConverting bipolar to unipolar

Using unipolar converter when input signal is bipolar Scaling down the input Adding an offset

Bipolar Converter If polarity information in

output is desired Bipolar input range

Typically, 0 ~ 5V

Bipolar Output 2’s Complement Offset Binary Sign Magnitude …

Input signal is scaled and an offset is added

scaled

Addoffset

7

Outputs and Analog Reference SignalOutputs and Analog Reference Signal I/O of typical ADC

ADC output Number of bits

8 and 12 bits are typical 10, 14, 16 bits also available

Typically natural binary BCD (3½ BCD)

• For digital panel meter, and digital multimeter

Errors in reference signal From

Initial Adjustment Drift with time and

temperature

Cause Gain error in Transfer

characteristics To realize full accuracy of

ADC Precise and stable

reference is crucial Typically, precision IC

voltage reference is used• 5ppm/C ~ 100ppm/C

8

Control SignalsControl Signals

Start From CPU Initiate the conversion

process BUSY / EOC

To CPU Conversion is in

progress 0=Busy: In progress 1=EOC: End of

Conversion

HBE / LBE From CPU To read Output word

after EOC HBE

• High Byte Enable LBE

• Low Byte Enable

9

A/D Conversion TechniquesA/D Conversion Techniques

Counter or Tracking ADC Successive Approximation ADC

Most Commonly Used Dual Slop Integrating ADC Voltage to Frequency ADC Parallel or Flash ADC

Fast Conversion Software Implementation Shaft Encoder

10

Counter Type ADCCounter Type ADC Block diagram

Waveform

Operation Reset and Start Counter DAC convert Digital output

of Counter to Analog signal Compare Analog input and

Output of DAC Vi < VDAC

• Continue counting Vi = VDAC

• Stop counting Digital Output = Output of

Counter Disadvantage

Conversion time is varied 2n Clock Period for Full

Scale input

11

Tracking Type ADCTracking Type ADC

Tracking or Servo Type Using Up/Down

Counter to track input signal continuously

For slow varying input

Can be used as S/H circuit By stopping desired

instant Digital Output Long Hold Time

Disabling UP (Down) control, Converter generate Minimum (Maximum)

value reached by input signal over a given period

12

Successive Approximation ADCSuccessive Approximation ADC

Most Commonly used in medium to high speed Converters

Based on approximating the input signal with binary code and then successively revising this approximation until best approximation is achieved

SAR(Successive Approximation Register) holds the current binary value

Block Diagram

13

Successive Approximation ADCSuccessive Approximation ADC

Circuit waveform

Logic Flow

Conversion Time n clock for n-bit ADC Fixed conversion time

Serial Output is easily generated Bit decision are made

in serial order

14

Dual Slope Integrating ADCDual Slope Integrating ADC Operation

Integrate Reset and integrate Thus

Applications DPM(Digital Panel Meter),

DMM(Digital Multimeter), …

Excellent Noise Rejection High frequency noise

cancelled out by integration Proper T1 eliminates line

noise Easy to obtain good

resolution Low Speed

If T1 = 60Hz, converter throughput rate < 30 samples/s

1

0

T

iv dt2

0

t

rV dt1 ( ) 2i AVG rT v t V

2( )

1i AVG r

tv V

T

15

Voltage to Frequency ADCVoltage to Frequency ADC

VFC (Voltage to Frequency Converter) Convert analog input

voltage to train of pulses Counter

Generates Digital output by counting pulses over a fixed interval of time

Low Speed Good Noise Immunity High resolution

For slow varying signal With long conversion

time Applicable to remote data

sensing in noisy environments Digital transmission

over a long distance

16

Parallel or Flash ADCParallel or Flash ADC

Very High speed conversion Up to 100MHz for 8 bit

resolution Video, Radar, Digital

Oscilloscope Single Step Conversion

2n –1 comparator Precision Resistive

Network Encoder

Resolution is limited Large number of

comparator in IC

Homework #5-1 어떻게 동시에 비교가

되는지를 설명하라 .

17

Interface SoftwareInterface Software

Memory Mapped Transfers ADC is assigned in

Memory Space MRD, MWR signal MOV instruction

More complex decoding logic

I/O Mapped Transfers ADC is in I/O Space

IOR, IOW signal IN, OUT instruction

More Simple decoding logic

DMA (Direct Memory Access) CPU release system bus

by the request of DMA DMA controller carried out

data transfer by generating the required addresses and control signals

The system bus control reverts back to CPU when data transfer is finished

DMA is useful High Speed High volume data transfer

Disk Drive interface

18

DAS (Data Acquisition System)DAS (Data Acquisition System)

DAS performs the complete function of converting the raw outputs from one or more sensors into equivalent digital signals usable for further processing, control, or displaying applications

Applications Simple monitoring of a

single analog variable Control and Monitoring

of hundreds of parameters in a nuclear plant

19

Single Channel SystemSingle Channel System

Transducer Generate signal of low

amplitude, mixed with undesirable noise

Amplifier, Filters Amplify Remove noise Linearize

S/H (Sample and Hold) Reduce uncertainty error

in the converted output when input changes are fast compared to the conversion time

In Multi-channel system To hold a sample from

one channel while multiplexer proceed to sample next one

Simultaneous sampling of two signal

20

Sample and Hold CircuitsSample and Hold Circuits

Care in selecting hold capacitor Ch Low Value

Reduces acquisition time Increase Droop

High Value Minimize Droop Increase acquisition time

Choose capacitor to get a best acquisition time while keeping the droop per conversion below 1 LSB

21

Multi-channel SystemMulti-channel System

Analog multiplexer and a ADC Low cost

Local ADCs and digital multiplexer Higher sampling rate

22

How to select and use an ADCHow to select and use an ADC

Range of commercially available ADCs

Guidelines for using ADCs Use the full input range

of the ADC Use a good source of

reference signal Look out for fast input

signal changes Keep analog and digital

grounds separate Minimize interference

and loading problem

23

Commercially available monolithic Commercially available monolithic ADCsADCs

24

Commercially available hybrid ADCsCommercially available hybrid ADCs

25

Accuracy CalculationAccuracy Calculation

Better than 1% accuracy is ensured Actual accuracy with smooth input signal at room

temperature will be better than 0.5%