PRECISION “HEAVY DUTY” PRESSURE GAUGES · STANDARD PRESSURE GAUGES: PBX pressure gauge with bourdon tube 3 PBX-BI ... If required, calibration certificates from an independent

ZEAL

TRADE CATALOGUE 2005

PRECISION “HEAVY DUTY”PRESSURE GAUGES

18-A, 1st Floor, Jalan MJ/ 7, Medan Maju Jaya,7th Mile Off Jalan Klang Lama, 46000 Petaling Jaya,Selangor, Malaysia.Tel : 603- 77843918, 77840053, Fax : 603- 77844135E-mail : [email protected] , [email protected] : www.anslabzeal.com

ANSARI AGENCIES SDN.BHD.Distributer :

INDEX HIGH QUALITY "HEAVY - DUTY" PRESSURE GAUGES

PAGE

INDEX 1 GENERAL INFORMATION 2

STANDARD PRESSURE GAUGES: PBX pressure gauge with bourdon tube 3 PBX-BI economy Line-BI 4 PBX-SI economy Line-SI 5 PBX-TG test pressure gauge with bourdon tube of copper-breryllium 6 PBX-SF solid front pressure gauge acc. to DIN-16006 7 PBX-SF-HP solid front high pressure gauge, upto 7000 bar 8 PBB duplex pressure gauge with two bourdon tubes 9 PCX capsule pressure gauge for low pressures 10 PMX diaphragm type, all stainless steel 11 PPB square and rectangular case with bourdon tube 13 PPC square and rectangular case with capsule for low pressures 14

PRESSURE GAUGES WITH CHEMICAL SEAL:PBS chemical seal pressure gauge 15PFS chemical seal and capillary tube 16PFS-TL tank level pressure gauge capillary tube 17PBQ sanitary chemical seal 18PFQ sanitary chemical seal and capillary tube 19PBR chemical seal for high pressure with flush diaphragm 20PBT finger type chemical seal for high pressure 20

DIFFERENTIAL PRESSURE GAUGES: PCD capsule for low-differential pressure 21 PBD bourdon tube system 22 PMD diaphragm system 23 POD double Diaphragm system, overload safe upto 100 bar 24 POD double Diaphragm system, with 2 chemical seals 25

PRESSURE RECORDERS: RPX bourdon tube system 26

SUB-SEA PRESSURE GAUGES: PBX-SS bourdon tube system 27

Standard pressure ranges 0,6 upto 4000 Bar 28 Standard pressure ranges 4 upto 400 mBar 29 Marking and certificates for pressure gauges 29 Options on pressure gauges 30-31

ELECTRICAL DEVICES: Minimum pressure ranges for electrical devices 32 HZ Contact devices 33 Microswitch HZ Contact devices 34 Add-on Contact devices 35 Options on contact devices 35 Built-in transmitter devices 35

PAGE 1

■ GENERAL INFORMATION

■ This Catalogue is for ZEAL precision heavy duty Pressure Gauges.

■ ZEAL were established in 1888 to fulfill a demand for quality temperature and pressure instrumentation, either mechanical and/or electronic e.g. Temperature and Pressure Gauges, PT-100, Thermocouples, Pressure and Temperature Transmitters, Pressure and Temperature Switches, Bimetallic Thermometers, etc.Products are manufactured to the relevant British/Din standards to ISO-9001 quality approvals.

■ To find the complete specification for a PRESSURE GAUGE refer to the following:

EXAMPLE :PBX100XA

PAGE: 3 22

1. BASIC TYPE 2. PRESSURE RANGE 3. ELECTRICAL DEVICE 4. ANY OPTIONS

27 - 28 24 - 25

0 - 160 BAR M-1-HZ CONTACT BLOW-OUT DEVICE

■ Abbreviations used in this catalogue: O.D. = ON DEMAND; N.A. = NOT AVAILABLE.

■ Dimensions used in this catalogue are in: millimeters (mm).They are intended as a guide. ■ Your order will be confirmed by fax.

■ Other variations which are not mentioned in this catalogue are available on request.

■ CERTIFICATION AND REPAIR SERVICE

■ Certificates of Conformity to the company’s published specifications are available on request for all productsmanufactured and supplied by us.

■ Certificates of Calibration for all manufactured products are available. These certificates indicatedeviations from standards traceable to European N.K.O. or D.K.D. (Dutch/German National Standards).The results are recorded on a certificate which include calibration date, instrument serial number, type numberand the N.K.O. or D.K.D. standard used. If required, calibration certificates from an independent CALIBRATION LABORATORY can be supplied.

■ Material Certificates for all ZEAL manufactured products are available. These certificates indicate the specifications of the materials used.

■ An efficient repair and sparepart service is provided at competitive rates for ZEAL products and products ofother manufacturers. Instruments for repair should be sent carriage paid and labelled with the senders name andaddress, together with a brief description of the work required. We will advise you of the costs involved beforecommencement of the repair.

E&OE

PAGE 2

G.H. ZEAL LIMITEDZEAL HOUSE, 8 DEER PARK ROAD, LONDON SW19 3UU. ENGLAND.TEL: +44 (0)20 8542 2283 FAX: +44 (0)20 8543 7840 E-MAIL [email protected]

PRESSURE GAUGES, STAINLESS CASE, BRASS INTERNALS

ZEAL TYPE PBX, Economy Line-BI STANDARD MODEL

ELEMENT : bourdon tube of phosphor bronze SCALE : bar, kg/cm2, psi, kPa, standard EN range CONNECTION : brass, Ø63mm: ¼"BSP or ¼"NPT

: brass, Ø100 and Ø160mm : ½"BSP or ½"NPT CASE : AISI 304, fillable BEZEL : bayonet lock ring polished WINDOW : laminated safety glass POINTER : standard pointer for Ø63mm

: micro adjustable for Ø100 and Ø160mm CASE DIAMETER ( Ø in mm)

TYPE MODEL RANGE 63 100 160

A< 60 bar

PBX063XA-BI PBX100XA-BI PBX160XA-BI

> = 60-600 barPBX063XA-BI PBX100XA-BI PBX160XA-BI

B< 60 bar

PBX063XB-BI PBX100XB-BI PBX160XB-BI

> = 60-600 barPBX063XB-BI PBX100XB-BI PBX160XB-BI

C< 60 bar

PBX063XC-BI PBX100XC-BI PBX160XC-BI

> = 60-600 barPBX063XC-BI PBX100XC-BI PBX160XC-BI

H< 60 bar

PBX063XH-BI PBX100XH-BI PBX160XH-BI

> = 60-600 barPBX063XH-BI PBX100XH-BI PBX160XH-BI

J< 60 bar

PBX063XJ-BI PBX100XJ-BI PBX160XJ-BI

> = 60-600 barPBX063XJ-BI PBX100XJ-BI PBX160XJ-BI

PAGE 4

PRESSURE GAUGES, STAINLESS CASE, BRASS INTERNALS

ZEAL TYPE PBX, Economy Line-BI STANDARD MODEL

ELEMENT : bourdon tube of phosphor bronze SCALE : bar, kg/cm2, psi, kPa, standard EN range CONNECTION : brass, Ø63mm: ¼"BSP or ¼"NPT

: brass, Ø100 and Ø160mm : ½"BSP or ½"NPT CASE : AISI 304, fillable BEZEL : bayonet lock ring polished WINDOW : laminated safety glass POINTER : standard pointer for Ø63mm

: micro adjustable for Ø100 and Ø160mm CASE DIAMETER ( Ø in mm)

TYPE MODEL RANGE 63 100 160

A< 60 bar

PBX063XA-BI PBX100XA-BI PBX160XA-BI

> = 60-600 barPBX063XA-BI PBX100XA-BI PBX160XA-BI

B< 60 bar

PBX063XB-BI PBX100XB-BI PBX160XB-BI

> = 60-600 barPBX063XB-BI PBX100XB-BI PBX160XB-BI

C< 60 bar

PBX063XC-BI PBX100XC-BI PBX160XC-BI

> = 60-600 barPBX063XC-BI PBX100XC-BI PBX160XC-BI

H< 60 bar

PBX063XH-BI PBX100XH-BI PBX160XH-BI

> = 60-600 barPBX063XH-BI PBX100XH-BI PBX160XH-BI

J< 60 bar

PBX063XJ-BI PBX100XJ-BI PBX160XJ-BI

> = 60-600 barPBX063XJ-BI PBX100XJ-BI PBX160XJ-BI

PAGE 4

PRESSURE GAUGES, ALL STAINLESS STEELZEAL TYPE PBX, Economy Line-SI

STANDARD MODEL ELEMENT : bourdon tube of AISI316Ti (1.4571)

SCALE : bar, kg/cm2, psi, kPa, standard EN range

CONNECTION : AISI316Ti (1.4571), Ø63mm: ¼" BSP or ¼"NPT

: AISI316Ti (1.4571), Ø100 and Ø160mm : ½" BSP or ½"NPT

CASE : AISI 304 (1.4301), fillable

BEZEL : bayonet lock ring polished

WINDOW : laminated safety glass

POINTER : standard pointer for Ø63mm: micro adjustable for Ø100 and Ø160mm

CASE DIAMETER ( Ø in mm)TYPE MODEL RANGE 63 100 160

A< 60 bar

PBX063XA-SI PBX100XA-SI PBX160XA-SI

> = 60-600 barPBX063XA-SI PBX100XA-SI PBX160XA-SI

B< 60 bar

PBX063XB-SI PBX100XB-SI PBX160XB-SI

> = 60-600 barPBX063XB-SI PBX100XB-SI PBX160XB-SI

C< 60 bar

PBX063XC-SI PBX100XC-SI PBX160XC-SI

> = 60-600 barPBX063XC-SI PBX100XC-SI PBX160XC-SI

H< 60 bar

PBX063XH-SI PBX100XH-SI PBX160XH-SI

> = 60-600 barPBX063XH-SI PBX100XH-SI PBX160XH-SI

J< 60 bar

PBX063XJ-SI PBX100XJ-SI PBX160XJ-SI

> = 60-600 barPBX063XJ-SI PBX100XJ-SI PBX160XJ-SI

CASE DIAMETER ( Ø in mm)HIGHER RANGES RANGE 63 100 160

Additional to base price 60-600 bar 1000 barAdditional to base price 60-600 bar 1600 bar N/A

PAGE 5

"CLASS 0,25 TEST PRESSURE GAUGES, TYPE PBX-TGZEAL TYPE PBX-TG, with bourdon tube of copper-beryllium

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 BOURDON TUBE : Copper/Beryllium WINDOW : mineral glass 4 mm DIAL : Mirrorscale aluminium, black figures on white POINTER : knife edge aluminium, black CONNECTION : ½"BSP or ½"NPT, AISI316Ti/1.4571 RANGE : from 0 - 1 upto 0-60 bar, acc. to EN 837-1

or from 0-15 psi upto 1.000 psi ACCURACY : 0,25% F.S. / class 0,25 MOVEMENT : stainless steel AISI304/1.4301 CALIBRATION REPORT : included, minimal 10 points OPTIONS / GRADUATIONS : see page 28-31

CASE DIAMETER (Ø in mm)TYPE MODEL 160 250

APBX-TG-160XA PBX-TG-250XA

BPBX-TG-160XB PBX-TG-250XB

CPBX-TG-160XC PBX-TG-250XC

DPBX-TG-160XD PBX-TG-250XD

FPBX-TG-160XF PBX-TG-250XF

HPBX-TG-160XH PBX-TG-250XH

JPBX-TG-160XJ PBX-TG-250XJ

OPTIONS EXTRA COSTS

HIGHERRANGES

0-100 bar / 0-1.500 psi

0-250 bar / 0-3.000 psi

0-400 bar / 0-6.000 psi

0-600 bar / 0-10.000 psi

0-1000 bar / 0-15.000 psi

DOUBLESCALE

bar / psibar / kPa

ect.

PAGE 6

"ALL-STAINLESS" SOLID-FRONT PRESSURE GAUGES, TYPE PBX-SF

ZEAL TYPE PBX-SF, full safety pattern according to EN 837-1 STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : -1/0 and 0-0,6 - 60 bar,

solid front & blow-out back acc. to EN 837-1 acc. to EN 837-1 (see page 28)

WETTED PARTS : bourdon tube + connection AISI316Ti/1.4571 for higher ranges (max. 4000 bar): see page 28

WINDOW : safety glass ACCURACY : case Ø 63 : ± 1.6% F.S. / class 1.6

DIAL : aluminium, black figures on white case Ø100 and Ø160 : ± 1.0% F.S./class 1

POINTER : aluminium, black MOVEMENT : AISI304/1.4301

CONNECTION : Ø63mm: ¼"BSP or ¼"NPT APPLICATION : general and heavy industry Ø100 and Ø160mm : ½"BSP or ½"NPT OPTIONS : electrical contact, see page 33-35

CASE DIAMETER ( Ø in mm)TYPE MODEL 63 100 160

A

B

D

OPTIONS EXTRA COSTS

LxLIQUID FILLED CASE:

GLYCERINE

(in combination with electrical device: OIL see page 35)

"Hz" CONTACTDEVICE

EXCLUDING "Hz" CONTACT(see page 33)

O2 * for oxygen use

* liquid filled on demand

PAGE 7

PBX-SF063Lx PBX-SF100Lx PBX-SF160Lx

ON DEMAND

PBX-SF160XDPBX-SF063XD PBX-SF100XD

PBX-SF160XB

PBX-SF063XA

PBX-SF063XB PBX-SF100XB

PBX-SF100XA PBX-SF160XA

"ALL-STAINLESS" SOLID-FRONT PRESSURE GAUGES, TYPE PBX-SF-HP

ZEAL TYPE PBX-SF-HP, full safety pattern according to EN 837-1 STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : 0 - 4000 bar upto 0 - 6000 bar

solid front & blow-out back acc. to EN 837-1 for higher ranges (max. 7000 bar): see below

WETTED PARTS : spiral wound tube, HP160 ACCURACY : ± 1.0% F.S./class 1

WINDOW : safety glass ± 0.6% F.S./class 0.6 on demand

DIAL : aluminium, black figures on white MOVEMENT : AISI304/1.4301

POINTER : aluminium, black

CONNECTION : 9/16" UNF x18 H.P. female, AISI316Ti, 1.4571

CASE DIAMETER ( Ø in mm)TYPE MODEL 160

APBX-SF-HP160XA

BPBX-SF-HP160XB

DPBX-SF-HP160XD

OPTIONS EXTRA COSTS


GLYCERINE

PBX-SF-HP160Lx

Range 0 - 7000 bar

PAGE 8

STAINLESS STEEL DUPLEX PRESSURE GAUGE, TYPE PBBZEAL TYPE PBB, with double bourdon-tube and two pointers

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 RANGES : -1/0 and 0-0,6 - 60 bar, acc. to EN 837-1 (see page 28)

WETTED PARTS : double bourdon tube AISI316Ti/1.4571 for higher ranges (max. 1600 bar), see page 28

WINDOW : mineral 4 mm MOVEMENT : brass

DIAL : aluminium, black figures on white ACCURACY : Ø 100 and Ø 160 mm± 1.0% F.S./class 1.0

POINTERS : two pointers, 1x black and 1x red, aluminium APPLICATIONS : general industry

CONNECTION : Ø100 and Ø160 mm : 2x ½"BSP or ½"NPT OPTIONS : see page 24-25, electrical contact or transmitters 4-20mA, 0-20mA, 0-10Vdc see page 32-35.

CASE DIAMETER xxx (Ø in mm)TYPE MODEL 100 160

K

L

M

N

O

HOPTION EXTRA COSTS


GLYCERINE

(in combination with electrical device: OIL see page 35)

DIFFERENTIALSCALE

SMALL SCALE IN CENTER TO READ DIFFERENTIAL PRESSURE

"Hz" CONTACT DEVICE

EXCLUDING "Hz" CONTACT: ONLY POSSIBLE ON ONE POINTER (see page 35)

PAGE 9

PBB100XK PBB160XK

PBB100XL PBB160XL

PBB100XM PBB160XM

PBB100XN PBB160XN

PBB100XO PBB160XO

PBB100XH PBB160XH

PBB100Lx PBB160Lx

0 6BAR

STAINLESS STEEL LOW PRESSURE GAUGES, TYPE PCX

ZEAL TYPE PCX, with capsule measuring element STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-45 RANGE : Ø100: 0-25 upto 0-400 mbar, acc to EN 837-3: see page 29

WETTED PARTS : capsule AISI316/1.4401 Ø160: 0-4 upto 0-400 mbar, acc to EN 837-3: see page 29

WINDOW : mineral glass 4 mm Ø250: 0-10 upto 0-400 mbar, acc to EN 837-3: see page 29

DIAL : aluminium, black figures on white available in vacuum , compound and pressure

POINTER : aluminium, black ACCURACY : ± 1.6% F.S./class 1.6

CONNECTION : ½"BSP or ½"NPT, AISI316Ti/1.4571 APPLICATIONS : only for low-air and dry gases

MOVEMENT : nickel plated brass with external OPTIONS : see page 24-25, electrical contact only possible with

adjustment device case Ø160 mm: type I-Intervall see page 33

CASE DIAMETER xxx (Ø in mm)TYPE MODEL 100 160 250

APCX160XA PCX250XA

BPCX160XB PCX250XB

DPCX160XD PCX250XD

EPCX160XE PCX250XE

GPCX160XG PCX250XG

HPCX160XH PCX250XH

OPTION EXTRA COSTSOVERRANGEPROTECTION

MAXIMUM UPTO 10 TIMES FULL SCALE (max. 2 bar)

ELECTRICALDEVICE "Hz" CONTACT ONLY for case Ø160 mm: type I-Intervall see page 33

NOTE : LIQUID FILLING NOT POSSIBLE WITH TYPE PCX

PAGE 10

PCX100XG

PCX100XH

PCX100XD

PCX100XE

PCX100XA

PCX100XB

DIAPHRAGM TYPE PRESSURE GAUGE, TYPE PMX

ZEAL TYPE PMX, all stainless steel with diaphragm STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-65 RANGES : diaphragm Ø160 mm: 25 upto 400 mbar, acc. to EN 837-3

WETTED PARTS : diaphragm AISI316Ti/1.4571 other on demand diaphragm Ø100 mm: 0,6 upto 25 bar, acc. to EN 837-3

WINDOW : mineral glass 4 mm vacuum, compound and pressure, (see page 28-29)

DIAL : aluminium, black figures on white ACCURACY : case Ø100 and Ø160 : ± 1.6% F.S./class 1.6

POINTER : aluminium, black APPLICATION : general and heavy industry

MOVEMENT : AISI304/1.4301 OPTIONS : see page 30-31, electrical contacts see page 32-35

PRESSURE CASE DIAMETER xxx (Ø in mm)

TYPE MODEL CONNECTION MIN MAX 100 160

PMXxxxXA-02 ½"BSP or ½"NPT, AISI316/1.4401

PMXxxxXA-03½"BSP or ½"NPT,

POLYPROPYLENEPTFE diaphragm

PMXxxxXA-04 ½"BSP, PTFE lining

PMXxxxXA-06 ½"BSP or ½"NPT, AISI316/1.4401 25 mbar

PMXxxxXA-07 ½"BSP, PTFE lining 40 mbar

PMXxxxXA-09 DIN-NW25 PN40 AISI316/1.4401

PMXxxxXA-10 DIN-NW25 PN40 PTFE LINING

PMXxxxXA-12 DIN-NW50 PN16-40 AISI316/1.4401

PMXxxxXA-14 DIN-NW50 PN16-40 PTFE LINING

PMXxxxXA-16 Ø100x83x6xM8AISI316/1.4401 0.6 bar 25 bar

PMXxxxXA-181"ASA 150-600# or

DIN-NW25 PN16-40 AISI316/1.4401

PMXxxxXA-191½"ASA 150-600# or DIN-NW40 PN16-40

AISI316/1.44010.6 bar 25 bar

PMXxxxXA-202"ASA 150-600# or

DIN-NW50 PN16-40 AISI316/1.4401

PMXxxxXA-211"ASA 150# or

DIN-NW25 PN16 AISI316/1.4401

PMXxxxXA-221½"ASA 150# or DIN-NW40 PN16 AISI316/1.4401

25 mbar 400 mbar

PMXxxxXA-232"ASA 150# or

DIN-NW50 PN16 AISI316/1.4401

OPTIONS EXTRA COSTSPMXxxxLA-xx GLYCERINE FILLED CASE (in combination 0.6 bar 25 bar

with electrical contact: OIL see page 35) 40 mbar 400 mbar

OVERRANGEPROTECTION UPTO 5 TIMES FULL SCALE (MAX. 40 bar) 25 mbar 25 bar

FOR TYPE PMX WITH BACK CONNECTION: SEE NEXT PAGE

PAGE 11

0.6 bar 25 bar

400 mbar

0.6 bar 25 bar

0.6 bar 25 bar

ZEAL DIAPHRAGM TYPE PRESSURE GAUGE, TYPE PMX TYPE PMX, stainless steel with diaphragm and back connection

STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-45 RANGES : diaphragm Ø160 mm: 25 upto 400 mbar, acc. to EN 837-3

WETTED PARTS : diaphragm AISI316Ti/1.4571 diaphragm Ø100 mm: 0,6 upto 25 bar, acc. to EN 837-3

WINDOW : mineral glass 4 mm vacuum, compound and pressure (see page 28-29)

DIAL : aluminium, black figures on white ACCURACY : case Ø100 and Ø160 : ± 1.6% F.S./class 1.6


MOVEMENT : nickel plated brass with external adjustment device OPTIONS : see page 30-31, electrical contact only possible with case Ø160 mm: type I-Intervall: see page 32-33

PRESSURE CASE DIAMETER xxx (Ø in mm)

TYPE MODEL CONNECTION MIN MAX 100 160

PMX100XE-02 ½"BSP or ½"NPT, AISI316/1.4401 0.6 bar 25 bar

PMX160XE-02 ½"BSP or ½"NPT, AISI316/1.4401 25 mbar 400 mbar

PMX100XG-02 ½"BSP or ½"NPT, AISI316/1.4401 0.6 bar 25 bar

PMX160XG-02 ½"BSP or ½"NPT, AISI316/1.4401 25 mbar 400 mbar-

PMX100XE-05 DIN-NW25 PN40 AISI316/1.4401

PMX100XE-06 DIN-NW25 PN40 PTFE LINING

PMX160XE-08 DIN-NW50 PN40 AISI316/1.4401 25 mbar 400 mbar

PMX160XE-09 DIN-NW50 PN40 PTFE LINING 40 mbar 400 mbar

OPTIONS MIN MAX EXTRA COSTSOVERRANGEPROTECTION

UPTO 5 TIMES FULL SCALE (MAX. 40 bar) 25 mbar 25 bar

ELECTRICALDEVICE "Hz" CONTACT ONLY for case Ø160 mm: type I-Intervall see page 32-33

NOTE: LIQUID FILLING NOT POSSIBLE

PAGE 12

0.6 bar 25 bar

SQUARE AND RECTANGULAR PRESSURE GAUGESZEAL TYPE PPB, with bourdon tube for panel mounting

CASE : profile, glassfibre reinforced black Noryl CONNECTION : ¼"BSP or ¼"NPT female, AISI316Ti/1.4571

IP-45 RANGE : see table, higher pressure (max. 1000 bar) see page 28

WETTED PARTS : bourdon tube, see table MOVEMENT : see table

WINDOW : plexiglass ACCURACY : see table

DIAL : aluminium, black figures on white OPTIONS : see page 30-31, electrical contact, transmitters page 32-35

POINTER : aluminium, black

CASE DIMENSIONS (in mm)TYPE MODEL 72x72 96x96 144x144 192x192

SPPB72x72XS PPB96x96XS PPB144x144XS PPB192x192XS

WETTED PARTS : brass brass AISI316Ti/1.4571 AISI316Ti/1.4571SQUARE RANGE : 0-1 upto 60 bar 0-1 upto 60 bar 0-0,6 upto 60 bar 0-0,6 upto 60 bar

ACCURACY : ±1.6%F.S./cl. 1.6 ±1.6%F.S./cl. 1.6 ±1,0%F.S./cl. 1.0 ±1.0%F.S./cl. 1.0MOVEMENT : brass brass AISI304/1.4301 AISI304/1.4301

TYPE MODEL 72x144 96x192

VWETTED PARTS : AISI316Ti/1.4571 AISI316Ti/1.4571

VERTICAL RANGE : 0-0,6 upto 60 bar 0-0,6 upto 60 barACCURACY : ±1.0%F.S./cl. 1.0 ±1.0%F.S./cl. 1.0MOVEMENT : AISI304/1.4301 AISI304/1.4301


H

WETTED PARTS : AISI316Ti/1.4571 AISI316Ti/1.4571HORIZONTAL RANGE : 0-0,6 upto 60 bar 0-0,6 upto 60 bar

ACCURACY : ±1.0%F.S./cl. 1.0 ±1.0%F.S./cl. 1.0MOVEMENT : AISI304/1.4301 AISI304/1.4301

CASE DIMENSIONS (in mm)OPTIONS 72x72 96x96 144x144 192x192

CASE MATERIAL AISI304/1.4301, only for 96x96mm N.A. N.A. N.A.

WETTED PARTS AISI316Ti/1.4571 standard standard

PPB DOUBLE MEASURING SYSTEM AISI316Ti/1.4571 N.A.

DUPLEX VERTICAL HORIZONTALDOUBLE MEASURING SYSTEM

AISI316Ti/1.4571ALL DIMENSIONS

ELECTRIC LIGHT INSIDE CASE 12Vdc or 24Vdc with connector

NOTE:LIQUID FILLING NOT POSSIBLE FOR TYPE PPB, ELECTRICAL DEVICE

ONLY POSSIBLE WITH AISI316Ti/1.4571 WETTED PARTS

PAGE 13

PPB72x144XV PPB96x192XV

PPB144x72XH PPB192x96XH

SQUARE AND RECTANGULAR LOW PRESSURE GAUGES

TYPE PPC, for panel mounting with capsule measuring element CASE : profile, glassfibre reinforced black Noryl CONNECTION : ¼"BSP or ¼"NPT, female, AISI316Ti/1.4571

IP-45 RANGE : see table, acc. to EN, see page 29

WETTED PARTS : capsule, see table MOVEMENT : see table

WINDOW : plexiglass ACCURACY : see table

DIAL : aluminium, black figures on white APPLICATIONS : only for low-air and dry gases POINTER : aluminium, black OPTIONS : see page 30-31, electrical devices: not possible

CASE DIMENSIONS (in mm)TYPE MODEL 72x72 96x96 144x144 192x192

SPPC72x72XS PPC96x96XS PPC144x144XS PPC192x192XS

WETTED PARTS : brass brass AISI316Ti/1.4571 AISI316Ti/1.4571SQUARE RANGE : 0-40 upto 400mbar 0-25 upto 400mbar 0-4 upto 400mbar 0-4 upto 400mbar

ACCURACY : ±1.6%F.S./cl. 1.6 ±1.6%F.S./cl. 1.6 ±1.6%F.S./cl. 1.6 ±1.6%F.S./cl. 1.6MOVEMENT : brass brass nickel plated brass nickel plated brass


VPPC72x144XV PPC96x192XV

WETTED PARTS : AISI316Ti/1.4571 AISI316Ti/1.4571VERTICAL RANGE : 0-10 upto 400mbar 0-4 upto 400mbar

ACCURACY : ±1,6%F.S./class 1.6 ±1.6%F.S./class 1.6MOVEMENT : nickel plated brass nickel plated brass


HPPC144x72XH PPC192x96XH

WETTED PARTS : AISI316Ti/1.4571 AISI316Ti/1.4571HORIZONTAL RANGE : 0-10 upto 400mbar 0-4 upto 400mbar

ACCURACY : ±1,6%F.S./class 1.6 ±1.6%F.S./class 1.6MOVEMENT : nickel plated brass nickel plated brass

CASE DIMENSIONS (in mm)OPTIONS 72x72 96x96 144x144 192x192

CASE MATERIAL AISI304/1.4301, only for 96x96 mm N.A. N.A. N.A.OVERRANGEPROTECTION MAXIMUM UPTO 10 TIMES FULL SCALE N.A.

OVERRANGE 72x144 96x192 144x72 192x96PROTECTION MAXIMUM UPTO 10 TIMES FULL SCALE

72x72 96x96WETTED PARTS AISI316Ti/1.4571

ALL DIMENSIONSELECTRIC LIGHT

INSIDE CASE12Vdc or 24Vdc with connector

NOTE: LIQUID FILLING AND ELECTRICAL DEVICE NOT POSSIBLE WITH PPC

PAGE 14

"ALL-STAINLESS" DIAPHRAGM SEAL PRESSURE GAUGES, TYPE PBSZEAL TYPE PBS, with chemical seal

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : -1/0 upto 0-60 bar acc. to EN 837-1 (see page 28) WETTED PARTS : AISI316/1.440, other on demand high pressure ranges (max. 600 bar): see page 28 WINDOW : mineral glass 4 mm ACCURACY : case Ø 63 and Ø 80 mm: ±1.6% F.S./class 1.6 DIAL : aluminium, black figures on white case Ø 100 and Ø 160 mm: ±1.0% F.S. /class 1.0 POINTER : aluminium, black Tprocess : -20/+120 °C (-40°C upto +250°C on demand) MOVEMENT : stainless steel AISI304/1.4301 OPTIONS : see page 24-25, electrical contact or transmitter 4-20 mA,

0-20mA, 0-10Vdc: see page 32-35EXAMPLE: PBS100XA-06

MINIMUM MAXIMUM CASE DIAMETER xxx (Ø in mm)TYPE SEAL MODEL DN PN PN 063 080 100 160

PBSxxxXA-01 ½"BSP/NPT 25 bar 600 bar N.A.

PBSxxxXA-02 ¾"BSP/NPT 16 bar 600 bar N.A.

PBSxxxXA-03 FLUSH DIAPHRAGM 1"BSP/NPT 1,6 bar 600 bar N.A.

PBSxxxXA-04 1"BSPFEMALE 25 bar 600 bar N.A.

PBSxxxXA-05FLUSH DIAPHRAGM

1L"BSPFEMALE 25 bar 600 bar N.A.

PBSxxxXA-06 ½"BSP/NPT 1,6 bar 40 bar

PBSxxxXA-07 ¾"BSP/NPT 1,6 bar 40 bar

PBSxxxXA-08 INTERNAL DIAPHRAGM 1"BSP/NPT 1,6 bar 40 bar

PBSxxxXA-09 ½"BSP/NPTMALE 1 bar 100 bar

PBSxxxXA-10INTERNAL DIAPHRAGM

½"BSP/NPTMALE 100 bar 250 bar

PBSxxxXA-11 ½"BSP/NPTFEMALE 1 bar 100 bar

PBSxxxXA-12INTERNAL DIAPHRAGM

½"BSP/NPTFEMALE 100 bar 250 bar

PBSxxxXA-13* 1"ASA or NW25-DIN 1,6 bar 150# or

PN40

PBSxxxXA-14* 1½"ASA or NW40-DIN 1,6 bar 150# or

PN40

PBSxxxXA-15* INTERNAL DIAPHRAGM2"ASA or NW50-DIN 1,6 bar 150# or

PN40

PBSxxxXA-16* 1"ASA or NW25-DIN 1,6 bar 150# or

PN40

PBSxxxXA-17* 1½"ASA or NW40-DIN 1 bar 150# or

PN40

PBSxxxXA-18* FLUSH DIAPHRAGM2"ASA or NW50-DIN 1 bar 150l# or

PN40

OPTIONS EXTRA COSTSPTFE (LINING)

WETTED PARTS FOR TYPES: XX= 16, 17 AND 18,other types on demand

PBSxxxXC-xx

EXAMPLE: PBSxxxXC-06

OFF-CENTRE BACK CONNECTION

COOLINGELEMENT

FOR ALL A.M. TYPES PROCESS TEMPERATURES

UPTO +250°C

for all types EXAMPLE: PBSxxxXC-09

PBSxxxLx-xx CASE GLYCERINE FILLED (in combination with electrical device: OIL see page 35)

* Other pressure ratings, flange sizes, materials and in-line connections on demand

PAGE 15

"ALL-STAINLESS" PRESSURE GAUGES WITH CAPILLARY, TYPE PFSZEAL TYPE PFS, capillary tube with chemical seal

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : -1/0.6 upto 0-60 bar acc. to EN 837-1 (see page 28) WETTED PARTS : AISI316Ti/1.4571, others on demand higher pressure ranges (max. 600 bar): see page 28 WINDOW : mineral glass 4 mm ACCURACY : case Ø 63 and Ø 80 mm: ±1.6% F.S./class 1.6 DIAL : aluminium, black figures on white case Ø 100 and Ø 160 mm: ±1.0% F.S. /class 1.0 POINTER : aluminium, black Tprocess : -20/+120° Celcius (-40°C upto +400°C on demand) MOVEMENT : stainless steel AISI304/1.4301 OPTIONS : see page 30-31, electrical contact or transmitter 4-20 mA, CAPILLARY : AISI304/1.4301 plain or armoured PFSxxxXB-xx 0-20mA, 0-10Vdc: see page 32-35

MINIMUM MAXIMUM CASE DIAMETER xxx (Ø in mm)TYPE SEAL MODEL DN PN PN 063 080 100 160

PFSxxxXB-011"BSP

TURNINGNIPPLE

25 bar 600 bar N.A.

PFSxxxXB-02FLUSH DIAPHRAGM

1¼" BSP COUPLING

NUT25 bar 600 bar N.A.

PFSxxxXB-03 ½"BSP/NPTMALE 1.6 bar 100 bar

PFSxxxXB-04INTERNAL DIAPHRAGM

½"BSP/NPTMALE 100 bar 250 bar

PFSxxxXB-05 ½"BSP/NPTFEMALE 1.6 bar 100 bar

PFSxxxXB-06INTERNAL DIAPHRAGM

½"BSP/NPTFEMALE 100 bar 250 bar

PFSxxxXB-07* 1"ASA or NW25-DIN 1.6 bar 150# or

PN16

PFSxxxXB-08* 1½"ASA or NW40-DIN 1.6 bar 150# or

PN40

PFSxxxXB-09* INTERNAL DIAPHRAGM 2"ASA or NW50-DIN 1.6 bar 150# or

PN40

PFSxxxXB-10* 1"ASA or NW25-DIN 2.5 bar 150# or

PN40

PFSxxxXB-11* 1½"ASA or NW40-DIN 1.6 bar 150# or

PN40

PFSxxxXB-12* FLUSH DIAPHRAGM 2"ASA or NW50-DIN 1.6 bar 150# or

PN40

CAPILLARY TUBE EXTRA COSTSPLAIN

CAPILLARYAISI321/1.4541

d= 3,18 mmFIRST 1000 MM : PER 1000 MM

EXTRA :

ARMOUREDCAPILLARY

AISI304/1.4301d= 6 mm

FIRST 1000 MM : PER 1000 MM EXTRA :

ARMOUREDCAPILLARY

AISI316/1.4401d= 6 mm

FIRST 1000 MM : PER 1000 MM EXTRA :

CASE DIAMETER xxx (Ø in mm)OPTIONS MODEL 063 080 100 160

PFSxxxXA-xx WALL-MOUNTING BRACKET BOTTOM ENTRY

PFSxxxXD-xx FRONT FLANGE BOTTOM ENTRY-

PFSxxxXH-xxMOUNTING BEZEL AND U-

CLAMP, OFF-CENTRE BACK ENTRY

PFSxxxXJ-xx FRONT FLANGE, OFF-CENTRE BACK ENTRY

PFSxxxLx-xx CASE GLYCERINE FILLED (in combination with electrical device: OIL see page 35)

* Other pressure ratings, flange sizes, materials and in-line connections on demand

PAGE 16

TANK LEVEL PRESSURE GAUGES, TYPE PFS-TLZEAL TYPE PFS-TL

STANDARD MODEL CASE : 160 mm, bayonet, AISI304/1.4301, IP-45

back flange, capillary bottom entry

WETTED PARTS : sensing element AISI316/1.4401

welded diaphragm

DIAL : aluminium, black figures on white

according to tank table, see sample

WINDOW : mineral glass 4 mm

POINTER : aluminium black

RANGE : 0 - 800 mmWG upto 0 - 10.000 mmWG

ACCURACY : ± 1.6% F.S./class 1.6

CAPILLARY : red copper with yellow PVC cover MOVEMENT : nickel plated brass

CASE DIAMETER ( Ø in mm)TYPE MODEL 160

ES

¾" BSP coupling nutPFS-TL160XB-ES

EM

¾" BSP coupling nutPFS-TL160XB-EM

IM

Tank wall mountingPFS-TL160XB-IM

FL

Flange 4"ANSI 150 lbs RFPFS-TL160XB-FL

EXTRA COSTSCapillary Cover First 1000 mm Per 1000 mm extra

STANDARD

d = 6 mm

red copper Yellow PVC

ARMOUREDCAPILLARY

d = 6 mm

red copper ArmourAISI304/1.4301

PAGE 17

Capillaryd

d

"ALL-STAINLESS" SANITARY PRESSURE GAUGES, TYPE PBQZEAL TYPE PBQ, with sanitary chemical seal

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301 RANGE : from -1/0 upto 0-40 bar, acc. to EN-837-1 (see page 28)

IP-65 ACCURACY : case Ø 63 and Ø 80 mm: ±1.6% F.S./class 1.6 WETTED PARTS : flush diaphragm, AISI316Ti/1.4571 case Ø 100 and Ø 160 mm: ±1.0% F.S. /class 1.0 WINDOW : mineral glass 4 mm Tprocess : -20°/+120° Celcius (-40°C upto 250°C on demand) DIAL : aluminium, black figures on white OPTIONS : see page 30-31, electrical contact or transmitter 4-20 mA, POINTER : aluminium, black 0-20mA, 0-10Vdc: see page 32-35 MOVEMENT : stainless steel AISI304/1.4301

PBQxxxXA-xxSEAL MINIMUM CASE DIAMETER xxx (Ø in mm)

TYPE MODEL NORM DN PN 063 080 100 160PBQxxxXA-01 DIN-11851 1"-NW25 1.6 bar

PBQxxxXA-02 1½"-NW40 1 bar

PBQxxxXA-03 GLAND PIECE + COUPLING NUT 2"-NW50 1 bar

PBQxxxXA-04 DIN-11851 1½"-NW40 1 bar

PBQxxxXA-05THREAD PIECE

2"-NW50 1 bar

PBQxxxXA-06 SMS 1145 1½"-NW40 1 bar

PBQxxxXA-07GLAND PIECE + COUPLING NUT

2"-NW50 1 bar

PBQxxxXA-08 SMS 1145 1½"-NW40 1 bar


2"-NW50 1 bar

PBQxxxXA-10 APV - RJT (BS) 1½"-NW40 1 bar


2"-NW50 1 bar

PBQxxxXA-12 APV - RJT (BS) 1½"-NW40 1 bar


2"-NW50 1 bar

PBQxxxXA-14 IDF-ISS ISO-2853 1½"-NW40 1 bar


2"-NW50 1 bar

PBQxxxXA-16 IDF-ISS ISO-2853 1½"-NW40 1 bar


2"-NW50 1 bar

PBQxxxXA-18 ISO-2852 1" - 1½" 1.6 bar

PBQxxxXA-19TRI-CLAMP

2" 1 bar

PBQxxxXA-20 VARIVENT NW 25-32 1 bar

PBQxxxXA-21TUCHENHAGEN VARIVENT IN-LINE

NW 40-65 1 bar

OPTIONS EXTRA COSTS

PBQxxxXC-xx OFF-CENTRE BACK CONNECTION

PBQxxxLx-xx CASE GLYCERINE FILLED (in combination with electrical device: OIL see page 35)

PAGE 18

"ALL-STAINLESS" SANITARY PRESSURE GAUGES, TYPE PFQZEAL TYPE PFQ, capillary tube with sanitary chemical seal

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : -1/0.6 upto 0-40 bar acc. to EN 837-1 (see page 28) WETTED PARTS : flush diaphragm, AISI316Ti/1.4571 ACCURACY : case Ø 63 and Ø 80 mm: ±1.6% F.S./class 1.6 WINDOW : mineral glass 4 mm case Ø 100 and Ø 160 mm: ±1.0% F.S. /class 1.0 DIAL : aluminium, black figures on white Tprocess : -20/+120° Celcius (-40°/+400°C on demand) POINTER : aluminium, black OPTIONS : see page 30-31, electrical contacts and/or transmitters MOVEMENT : stainless steel AISI304/1.4301 4-20mA, 0-20mA, 0-10Vdc: see page 32-35 CAPILLARY : AISI321/1.4541 plain or armoured PFQxxxXB-xx

SEAL MINIMUM CASE DIAMETER xxx (Ø in mm)TYPE NORM MODEL DN PN 063 080 100 160

PFQxxxXB-01 1"-NW25 1.6 bar

PFQxxxXB-02 1½"-NW40 1.6 bar

PFQxxxXB-03 GLAND PIECE + COUPLING NUT 2"-NW50 1.6 bar


PFQxxxXB-07GLAND PIECE + COUPLING NUT

2"-NW50 1.6 bar



2"-NW50 1.6 bar



2"-NW50 1.6 bar

PFQxxxXB-18 1" - 1½" 1.6 bar

PFQxxxXB-19TRI-CLAMP

2" 1.6 bar

PFQxxxXB-20 NW 25-32 1.6 bar

PFQxxxXB-21TUCHENHAGEN VARIVENT IN-LINE

NW 40-65 1.6 bar


CAPILLARYAISI321/1.4541

d= 3,18 mm FIRST 1000 MM : PER 1000 MM EXTRA :

ARMOUREDCAPILLARY

AISI304/1.4301d= 6 mm FIRST 1000 MM : PER 1000 MM

EXTRA :

ARMOUREDCAPILLARY

AISI316/1.4401d= 6 mm FIRST 1000 MM : PER 1000 MM

EXTRA :

CASE DIAMETER xxx (Ø in mm)OPTIONS 063 080 100 160

PFQxxxXA-xxWALL

MOUNTINGBRACKET

BOTTOM ENTRY

PFQxxxXD-xx FRONT FLANGEBOTTOM ENTRY 0 0 0 0

PFQxxxXH-xx

MOUNTINGBEZEL AND U-CLAMP, OFF-

CENTRE BACK ENTRY

PFQxxxXJ-xxFRONT FLANGE,

OFF-CENTREBACK ENTRY

PFQxxxLx-xx CASE GLYCERINE FILLED

PAGE 19

DIN 11851

SMS 1145

APV-RJT (BS)

IDF-ISS ISO-2853

ISO-2852

VARIVENT

ALL-STAINLESS" PRESSURE GAUGES FOR HOMOGENISERS TYPE PBR, chemical seal with flush diaphragm and built-in pulsation dampener

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : 0 + 25 upto 0 + 60 bar, standard acc. to EN 837-1 (see page 28) WETTED PARTS : flush diaphragm, AISI316Ti/1.4571 higher pressure ranges (max. 1000 bar): see page 28 WINDOW : mineral glass 4 mm ACCURACY : case Ø 100 and Ø 160 mm: ±1.0% F.S. /class 1.0 DIAL : aluminium, black figures on white Tprocess : -20°/+120° Celcius (-40°C upto +250°C on demand) POINTER : aluminium, black OPTIONS : see page 30-31, electrical contact or transmitter 4-20 mA, MOVEMENT : stainless steel AISI304/1.4301 0-20mA, 0-10Vdc: see page 32-35

CASE DIAMETER xxx (Ø in mm)TYPE MODEL CONNECTION 100 160

PBRxxxXA-01 WITHOUT FLANGE

PBRxxxXA-02WITH FLANGE

95x43x28 mm with 2 holes Ø17 mm on pitch 60 mm

TYPE PBT, finger type chemical seal with built-in pulsation dampener STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-65 RANGE : 0 + 16 upto 0 + 60 bar, standard acc. to EN 837-1 (see page 28) WETTED PARTS : tubular probe ±100 mm, AISI316Ti/1.4571 high pressure ranges (max. 1000 bar): see page 28 WINDOW : mineral glass 4 mm ACCURACY : case Ø 100 and Ø 160 mm: ±1.0% F.S. /class 1.0 DIAL : aluminium, black figures on white Tprocess : -20°/+120° Celcius (-40°C upto +250°C on demand) POINTER : aluminium, black OPTIONS : see page 30-31, electrical contact or transmitter 4-20 mA, MOVEMENT : stainless steel AISI304/1.4301 0-20mA, 0-10Vdc: see page 32-35

CASE DIAMETER xxx (Ø in mm)TYPE MODEL CONNECTION 100 160

PBTxxxXA-01 ½"BSP male

PBTxxxXA-02 ¾"BSP male

PBTxxxXA-03 1"BSP male

PBTxxxXA-04 ¾"BSP female

PBTxxxXA-05 1"BSP female

PBTxxxXA-06 1¼"BSP female

OPTIONS FOR TYPE PBR AND PBT EXTRA COSTS

PBRxxxXC-xxPBTxxxXC-xx

EXAMPLE: PBRxxxXC-01

OFF-CENTRE BACK CONNECTION

PBxxxxLx-xx CASE GLYCERINE FILLED (in combination with electrical device: OIL see page 35)

PAGE 20

STAINLESS STEEL LOW-DIFFERENTIAL PRESSURE GAUGE, TYPE PCD

ZEAL TYPE PCD, with capsule measuring element STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-66 RANGE : case Ø100: 0-25 upto 0-400 mbar WETTED PARTS : capsule AISI316Ti/1.4571 case Ø160: 0-6 upto 0-400 mbar WINDOW : macrolon 4 mm STATIC PRESSURE: : case Ø100: maximum 1.0 bar DIAL : aluminium, black figures on white case Ø160: maximum 1.0 bar POINTER : aluminium, black ACCURACY : ± 1.6% F.S./class 1.6 CONNECTION : 2x ½"BSP or ½"NPT, AISI316Ti/1.4571 APPLICATIONS : only for clean air and dry gases MOVEMENT : nickel plated brass OPTIONS : see page 30-31


KPCD100XK PCD160XK

LPCD100XL PCD160XL

MPCD100XM PCD160XM

NPCD100XN PCD160XN

OPCD100XO PCD160XO

HPCD100XH PCD160XH

OPTION EXTRA COSTS

OVERRANGEPROTECTION

UPTO 10 TIMES FULL SCALE maximum 2.0 bar

LIQUID FILLING NOT POSSIBLE WITH PCDCONTACT DEVICES NOT POSSIBLE

PAGE 21

NOTES:

STAINLESS STEEL DIFFERENTIAL PRESSURE GAUGE, TYPE PBD

ZEAL TYPE PBD, with bourdon-tube system STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-66 AVAILABLE DIFFERENTIAL PRESSURE RANGES: WETTED PARTS : double bourdon tube AISI316Ti/1.4571 DIFFERENTIAL MAX. STATIC PRESSURE WINDOW : mineral 4 mm 0 - 0.6 bar 3 bar DIAL : aluminium, black figures on white 0 - 1 bar 4 bar POINTER : aluminium, black 0 - 1.6 bar 6 bar CONNECTION : 2x ½"BSP or ½"NPT AISI316Ti/1.4571 0 - 2.5 bar 10 bar MOVEMENT : AISI304/1.4301 0 - 4 bar 16 bar ACCURACY : ± 1.6% F.S./class 1.6 0 - 6 bar 25 bar APPLICATIONS : general industry 0 - 10 bar 30 bar OPTIONS : see page 30-31, electrical contacts and 0 - 16 bar 40 bar

mechanical transmitters: see page 32-35 POINTER DEFLECTION BETWEEN 120° AND 180°


KPBD100XK PBD160XK

LPBD100XL PBD160XL

MPBD100XM PBD160XM

NPBD100XN PBD160XN

OPBD100XO PBD160XO

HPBD100XH PBD160XH

OPTION EXTRA COSTS

LxPBD100Lx PBD160Lx

"Hz" CONTACT DEVICE

EXCLUDING "Hz" CONTACT (see page 33)

PAGE 22

LIQUID FILLED CASE: GLYCERINE(in combination with electrical contact:

OIL, see page 35)

STAINLESS STEEL DIFFERENTIAL PRESSURE GAUGE, TYPE PMD

ZEAL TYPE PMD, diaphragm system with two measuring chambers STANDARD MODEL

CASE : bayonet lock, AISI304/1.4301, IP-65 DIFFERENTIAL RANGE: Ø100 : 0-100 upto 400 mbar, max. static 100 bar WETTED PARTS : diaphragm AISI316Ti/1.4571 Ø100 : 0-0,6 upto 25 bar, max. static 100 bar WINDOW : mineral glass (4 mm) Ø160 : 0-0,6 upto 25 bar, max. static 100 bar DIAL : aluminium, black figures on white Ø160 : 0-25 upto 400mbar, max. static 25 bar POINTER : aluminium, black ACCURACY : case Ø100 and Ø160 : ± 1.6% F.S./class 1.6 CONNECTION : 2x ½"BSP or ½"NPT, AISI316/1.4401 APPLICATION : general and heavy industry MOVEMENT : AISI304/1.4301 OPTIONS : see page 30-31, electrical contacts and

mechanical transmitters: see page 32-35

CASE DIAMETER xxx (Ø in mm)100 100 160 160

TYPE MODEL 0-100 upto 400 mbar, max. static press. 100 bar

0-0,6 upto 25 bar, max. static pressure 100 bar

0-25 upto 400 mbar, max. static pressure 25 bar

0-0,6 upto 25 bar, max. static pressure 100 bar

KPMD100XK-low PMD100XK PMD160XK-low PMD160XK

LPMD100XL-low PMD100XL PMD160XL-low PMD160XL

MPMD100XM-low PMD100XM PMD160XM-low PMD160XM

NPMD100XN-low PMD100XN PMD160XN-low PMD160XN

OPMD100XO-low PMD100XO PMD160XO-low PMD160XO

OPTIONS EXTRA COSTS

Lx LIQUID FILLED CASE: GLYCERINE

(in combination with electrical device OIL: see page 35) PMD100Lx-low PMD100Lx PMD160Lx-low PMD160Lx

"Hz"CONTACT

DEVICE

EXCLUDING "Hz" CONTACT (see page 33) O.D. O.D.

PAGE 23

STAINLESS STEEL DIFFERENTIAL PRESSURE GAUGE, TYPE POD

TYPE POD, with double diaphragm system, max. st. press. 100 barmax. overload 100 bar on both sides

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 MOVEMENT : AISI304/1.4301 WETTED PARTS : diaphragms duratherm DIFFERENTIAL RANGE : 0-0,6 upto 25 bar

other AISI316/1.4401 ACCURACY : ± 1.6% F.S./class 1.6 WINDOW : safety glass STATIC PRESSURE : max. 100 bar DIAL : aluminium, black figures on white OVERLOAD : both sides upto 100 bar POINTER : aluminium, black APPLICATION : general and heavy industry CONNECTION : 2 x ¼"NPT female, AISI316Ti/1.4571 OPTIONS : electrical contacts and

at pitch 54 mm mechanical transmitters manifolds, swivel adapters


KPOD100XK POD160XK

LPOD100XL POD160XL

Y2" yoke, horizontal or vertical POD100XY POD160XY

OPTION EXTRA COSTS

Lx LIQUID FILLED CASE: GLYCERINE(in combination with electrical contact:

OIL, see page 35) POD100Lx POD160Lx

CONNECTION 2x ½"BSP or ½"NPT male

"Hz" CONTACT DEVICE

EXCLUDING "Hz" CONTACT(see page 33) ON DEMAND ON DEMAND

PAGE 24

DIAPHRAGM SEAL DIFFERENTIAL PRESSURE GAUGES, TYPE PODZEAL TYPE POD, with 2 x chemical seals

STANDARD MODEL CASE : bayonet lock, AISI304/1.4301, IP-65 MOVEMENT : AISI304/1.4301

with backflange (wall mounting) DIFFERENTIAL RANGE :min. 0-1 bar upto 0-25 bar

WETTED PARTS : AISI316/1.4401 ACCURACY : ± 1.6% F.S./class 1.6

WINDOW : safety glass STATIC PRESSURE : see below

DIAL : aluminium, black figures on white OVERLOAD : both sides upto static pressure


CAPILLARY : 2 x 1.000 mm, AIS321/1.4301 OPTIONS : electrical contacts, on page 33

CONNECTION : 2 x chemical seal see below

EXAMPLE: POD100XL-09SEAL MAXIMUM CASE DIAMETER xxx (Ø in mm)

TYPE SEAL MODEL CONNECTION PN 100 160PODxxxXL-06 ½"BSP/NPT 40 bar

PODxxxXL-07 ¾"BSP/NPT 40 bar

PODxxxXL-08 FIXED DIAPHRAGM 1"BSP/NPT 40 bar

PODxxxXL-09

INTERNAL WELDED DIAPHRAGM

½"BSP/NPT MALE 100 bar

PODxxxXL-11

INTERNAL WELDED DIAPHRAGM

½"BSP/NPTFEMALE 100 bar

PODxxxXL-13 1"ASA or NW25-DIN 150# or PN 40

PODxxxXL-14 1½"ASA or NW40-DIN 150# or PN 40

PODxxxXL-15 INTERNAL FIXED DIAPHRAGM2"ASA or NW50-

DIN 150# or PN 40

PODxxxXL-16

INTERNAL FIXED DIAPHRAGM

NW25-DIN, 4xM12 thread holes PN 40

PODxxxXL-18

INERNAL FIXED DIAPHRAGM

NW50-DIN PN 40

OPTIONS EXTRA COSTS

PODxxxXY-xx

example: POD100XY-xx

2" PIPE YOKE

PODxxxLx-xx CASE GLYCERINE FILLED in combination with electical device: oil see page 35

"Hz" CONTACT DEVICE EXCLUDING "Hz" CONTACT (see page 33)


CAPILLARY AISI321/1.4541 d= 3,18 mm FIRST2x1000 MM : standard PER 2x1000

MM EXTRA :

ARMOUREDCAPILLARY AISI304/1.4301 d= 6 mm FIRST

2x1000 MM :PER 2x1000 MM EXTRA :

ARMOUREDCAPILLARY AISI316/1.4401 d= 6 mm FIRST

2x1000 MM :PER 2x1000 MM EXTRA :

* Other pressure ratings, flange sizes and wetted parts on demand

PAGE 25

ON DEMAND ON DEMAND

STAINLESS STEEL PRESSURE RECORDERSZEAL TYPE RPX, with mechanical spring wound clock

STANDARD MODEL CASE : AISI316 / 1.4401 CHARTS 50 pcs. : Ø166mm for 192 x 192mm, WETTED PARTS : bourdon tube, AISI316Ti/1.4571 Ø223 for 288 x 288 mm WINDOW : plexiglass CONNECTION : ½"BSP or ½"NPT, AISI316Ti/1.4571 DIAL : transparent with black figures RANGE : -1/+0,6 upto 0-60 bar, acc. to DIN, PEN OPERATION : single or double-pen, writing with for higher ranges, see page 28

long-life fiber pens on disc MOVEMENT : brass CLOCKWORK : mechanical spring wound, 1-, 4-, 12- ACCURACY : ±1.0%F.S./class 1.0

24-hour or 7 day rotation. OPTIONS : see page 30-31

CASE DIMENSIONS192 x 192 mm 288 x 288 mm

H

PANEL MOUNTING

B

SURFACE MOUNTING

T

TRANSPORTABLE

CASE DIMENSIONSOPTIONS 192 x 192 mm 288 x 288 mm

RPX-DUPLEX DOUBLE MEASURING SYSTEM AISI316Ti/1.4571

CHARTS Ø 166 or Ø 223 mm, PER 100 PCS

SPARE PENS PER 5 PCS, black, red or blue

PAGE 26

RPX192x192XT RPX288x288XT

RPX192x192XH RPX288x288XH

RPX192x192XB RPX288x288XB

TYPE MODEL

"SUB SEA" PRESSURE GAUGES, TYPE PBX-SSZEAL TYPE PBX-SS, with pressure tight solid bar stock case

STANDARD MODEL

CASE : screwed bezel, AISI316/1.4401, RANGE : 0-6 upto 0-60 bar, acc. to EN 837-1 (see page 28)

pressure tight for depths down to see below for higher ranges (max. 1600 bar): see page 28

WETTED PARTS : bourdon tube + connection AISI316Ti/1.4571 ACCURACY : case Ø 63 : ± 1.6% F.S. / class 1.6

WINDOW : armoured glass 19mm thick case Ø100 and Ø160 : ± 1.0% F.S./class 1

DIAL : aluminium, black figures on white MOVEMENT : AISI304/1.4301

POINTER : aluminium, black APPLICATION : for operating at great depths of sea water

CONNECTION : Ø63mm: ¼"BSP or ¼"NPT and in hyperbaric conditions Ø100 and Ø160mm : ¼"BSP or ¼"NPT OPTIONS : see page 30-31

CASE DIAMETER ( Ø in mm)TYPE MODEL 63 (upto 1200m) 100 (upto 900 m) 160 (upto 450 m)

APBX-SS063XA PBX-SS100XA PBX-SS160XA

BPBX-SS063XB PBX-SS100XB PBX-SS160XB

CPBX-SS063XC PBX-SS100XC PBX-SS160XC

DPBX-SS063XD PBX-SS100XD PBX-SS160XD

JPBX-SS063XJ PBX-SS100XJ PBX-SS160XJ

OPTIONS EXTRA COSTS

GLYCERINE FILLED CASE:

SILICONE OIL FILLED CASE

PBX-SS063Lx PBX-SS100Lx PBX-SS160Lx

PAGE 27

Lx

STANDARD PRESSURE RANGES FOR TYPES:PBX, PBX-TG, PBX-SF, PBB, PMS, PMX, PPB, PBS, PFS, PBQ, PFQ, PBR, PBT, RPX, PBX-SS

PRESSURE RANGES EXTRA COSTSSCALE DIVISION

(in bar)***** OPTION

cl. 1.0cl. 1.6

cl. 0.6cl. 0.5

only PBX-TGcl. 0.3cl 0.25

Ø 63 Ø 80 Ø 100 Ø 160 Ø 250 72x72 96x96 144x144 192x192288x288

72x144144x72

192x9696x192

-1 ...0 0.02 0.005 × •

-1 ...0.6 0.05 0.01 × •

-1 ...1.5 0.05 0.02 × •

-1 ...3 0.1 0.02 × •

-1 ...5 0.1 0.05 × •

-1 ...9 0.2 0.05 × •

-1 ...15 0.5 0.1 × •

-1 ...24 0.5 0.2 × •

0 ...0.6 0.01 × × •

0 ...1 0.02 0.005 0.005 •

0 ...1.6 0.05 0.01 0.005 •

0 ...2.5 0.05 0.02 0.01 •

0 ...4 0.1 0.02 0.01 •

0 ...6 0.1 0.05 0.02 •

0 ...10 0.2 0.05 0.05 •

0 ...16 0.5 0.1 0.05 •

0 ...25 0.5 0.2 0.1 •

0 ...40 1 0.2 0.1 •

0 ...60 1 0.5 0.2 •

0 ...100 2 0.5 0.5

0 ...160 5 1 0.5

0 ...250 5 2 1

0 ...400 10 2 1

0 ...600 10 5 2

0 ...1000 20 5 5

0 ...1600 50 × × × × × × ×0 ...2500* 50 × × × × × × × × × × ×0 ...3000** 100 × × × × × × × × × × ×0 ...4000 upto 0 ...7000 see page 4a

NON STANDARD RANGES e.g. 0-7 bar or 0-110 psi DOUBLE SCALES e.g. bar/psi, bar/kPa, etc. FREON SCALES e.g. R12, R22, R504 ACCURACY ±1.6% F.S. (class 1.6) • • × × × • × × × × × ±1.0% F.S. (class 1.0) • • • • • • • •

±0.6 / 0.5 %F.S. (class 0.6 or 0.5)*** × × × × ±0.3 / 0.25 %F.S. (class 0.3 or 0.25) **** × × × **** **** × × × × × × Mirrorscale (standard for PBX-TG, page 6) × × × × × × × × × TRM scales for reciever gauges

0 ...100 % lin.0 ...10 square root

0.2 ...1 bar3 ...15 psi

20 ...100 kPa× NOT AVAILABLE * ELEMENT CrMo52 i.o. AISI316Ti/1.4571 *** ONLY FOR TYPE PBX OR PBX-SF• STANDARD ** ELEMENT NiSpan C i.o. AISI316Ti/1.4571 ****ONLY FOR TYPE PBX-TG see page 6

***** Scale in psi,kPa, kg/cm², mWC etc. available with no extra charge

PAGE 28

CASE DIMENSIONS ( in mm)

STANDARD PRESSURE RANGES FOR TYPES:PCX, PMS, PMX, PPC, PCD, PMD

PRESSURE RANGESSCALE DIVISION CASE DIMENSIONS (in mm)

(in mbar) ** cl. 1.6 optioncl. 1.0 Ø 100 Ø 160 Ø 250 72x72 96x96 144x144 192x192 72x144

144x72192x9696x192

-4 ...0 0 ...4 0.1 0.1 × • × × × • • × •

-6 ...0 0 ...6 0.1 0.1 × • × × × • • • •

-10 ...0 0 ...10 0.2 0.2 × • • × × • • • •

-16 ...0 0 ...16 0.5 0.5 × • • × × • • • •

-25 ...0 0 ...25 0.5 0.5 • • • × • • • • •

-40 ...0 0 ...40 1 1 • • • • • • • • •

-60 ...0 0 ...60 1 1 • • • • • • • • •

-100 ...0 0 ...100 2 2 • • • • • • • • •

-160 ...0 0 ...160 5 5 • • • • • • • • •

-250 ...0 0 ...250 5 5 • • • • • • • • •

-400 ...0 0 ...400 10 10 • • • • • • • • •

-2.5 ...1.5 -1.5 ...2.5 0.1 0.1 × • × × × • • × •

-4 ...2 -2 ...4 0.1 0.1 × • × × × • • • •

-6 ...4 -4 ...6 0.2 0.2 × • • × × • • • •

-10 ...6 -6 ...10 0.5 0.5 × • • × × • • • •

-15 ...10 -10 ...15 0.5 0.5 • • • × • • • • •

-25 ...15 -15 ...25 1 1 • • • • • • • • •

-40 ...20 -20 ...40 1 1 • • • • • • • • •

-60 ...40 -40 ...60 2 2 • • • • • • • • •

-100 ...60 -60 ...100 5 5 • • • • • • • • •

-150 ...100 -100 ...150 5 5 • • • • • • • • •

-250 ...150 -150 ...250 10 10 • • • • • • • • •

NON STANDARD RANGES:e.g. 0-50 mbar etc. DOUBLE SCALES e.g. mbar/mmWC, mbar/Pa, etc. ACCURACY ±1.6% F.S. / class 1.6 • • • • • • • • •

±1.0% F.S. / class 1.0 * ×

Mirrorscale × × × × × × ×

× NOT AVAILABLE • STANDARD * not for type PMS and PMX

** Scale in psi,kPa, kg/cm², mWC etc. available with no extra charge

MARKING FOR PRESSURE GAUGES OPTIONS EXTRA PRICE TAG number on dial TAG number on AISI304/1.4301 TAG plate 55x25 mm Lettering on dial Red mark on dial

CERTIFICATES FOR PRESSURE GAUGES TYPE OF CERTIFICATE EXTRA PRICE Certificate of Conformity acc. to EN 10204 2.2. Material certificate wetted parts acc. to EN 10204 3.1.B

2500-4000

Calibration certificate pressure gauge (Traceable to N.K.O.) (standard for PBX-TG page 6) Calibration certificate pressure gauge with transmitter (see page 35) (Traceable to N.K.O.) N.A. N.A.

Calibration certificates for type PBB (duplex) (Traceable to N.K.O.) N.A. N.A.

PAGE 29

Pressure (BAR) <=2500 >=4000

ZEAL'S OPTIONS ON PRESSURE GAUGESEXTRA COSTS

CASE CONNECTIONS CASE & BEZEL

TYPE DIMENSIONS(in mm)

1/8"BSP/NPTmax. 400 bar


1/2"BSP max. 1600 bar,

1/2"NPT max. 1000 bar


M20x1.5 max. 1600 bar

M16x1.5 H.P. female max.

7000 bar

9/16"UNFx18H.P. female

max. 7000 bar

AISI316 / 1.4401 *

BACK / FRONT FLANGE

AISI316/1.4401*

063 • ×080 • × ×100 •160 •250 • × ×063 • O ×100 • O160 • O100 • × ×160 • × ×100 • × ×160 • × ×250 • × × × ×100 • × × ×160 • × × ×

square • × × × ×rectangular • × × × ×

PBS - PBQ 063

PFS - PFQ 080 ON DEMAND: SEE ALSO PAGE 15-19 × ×100

160

100 SEE PAGE 20 ×160 ×100 • × ×160 • × ×100 • × × × ×160 • × × × ×100 • × × × ×160 • × × × ×

RPX ALL • × ×063 • • •100 • • •160 • • •

× NOT AVAILABLE • STANDARD O ON DEMAND * Not possible in combinations with contacts or transmitters

PAGE 30

PBX-SF

PBX

PPB - PPC

PBR - PBT

PMX

PCX

PBB

PBD

PMD -POD

PBX-SS

PCD

ZEAL'S OPTIONS ON PRESSURE GAUGESEXTRA COSTS

CASEWINDOW

MATERIAL BLOW- OUT POINTERS MEASURING SYSTEMTYPE DIMENSIONS

(in mm) PMMA - PLEXIGLASS SECURIT

LAMINATEDSAFETYGLASS

DISCPLUG * (LIQUIDFILLED)

ADJUSTABLEINDEX

POINTER ON GLASS

DRAGPOINTER

DRAGPOINTER in combination

with HZ contact

OIL & GREASE

FREE

MONELWETTEDPARTS

PULSATIONDAMPERAISI3161.4401

OVERLOAD2x F.S. other on demand

PBX 063 ×080 ×100

PBX-TG 160

250 × ×063 × × • × × ×100 × × • × ×160 × × • × ×100 ×160 ×100 × O × ×160 × O × ×250 × × × ×100 × ×160 × ×

PPB square • × × × × × O PPC rectangular • × × × × × × × × × O

PBS 063 × × O O PBQ 080 × × × O O PFS 100 O O PFQ 160 O O

PBR 100 O O PBT 160 O O

100 × × × × × × × × ×160 × × × × × × × × ×100 × ×160 × ×100 × × ×160 × × ×100 × × × ×160 × × × ×

RPX ALL × × × × • × × × × × ×063 × • × × × × × ×100 × • × × × × × ×160 × • × × × × × ×

× NOT AVAILABLE • STANDARD O ON DEMAND * WITH COMPENSATING DIAPHRAGM

PAGE 31

seepage 10

see page 11-12

seepage 21

POD

PMD

PBX-SS

PCX

PBX-SF

PMX

PBB

PCD

PBD

MINIMUM PRESSURE RANGE FOR PRESSURE GAUGES WITH ELECTRICAL DEVICE

TYPETYPE OF

CONTACT S-x S-xx S-xxx M-x M-xx M-xxx I-x I-xx I-xxx P-x P-xx MECHANICALTRANSMITTERS

PT-x(max.

1600 bar)case

dimensions MINIMUM RANGE (IN bar)PBX 100 1 1,6 4 1 1,6 4 1 1,6 1,6 1 1,6 1 1,6

160 1 1,6 2,5 1 1,6 2,5 1 1,6 1,6 1 1,6 1 1,6

PBX-SF 100 1 1,6 4 1 1,6 4 1 1,6 1,6 1 1,6 1 1,6

160 1 1,6 2,5 1 1,6 2,5 1 1,6 1,6 1 1,6 1 1,6

PBQ 100 1,6 1,6 4 1,6 1,6 4 1,6 1,6 1,6 1,6 1,6 1,6 2,5

160 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 1,6 2,5

PBS 100 1,6 1,6 4 1,6 1,6 4 1,6 1,6 1,6 1,6 1,6 1,6 2,5

160 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 1,6 2,5

PFQ 100 1,6 1,6 4 1,6 1,6 4 1,6 1,6 1,6 1,6 1,6 1,6 2,5

160 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 1,6 2,5

PFS 100 1,6 1,6 4 1,6 1,6 4 1,6 1,6 1,6 1,6 1,6 1,6 2,5

160 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 1,6 2,5

PBB** 100 1 1,6 4 1 1,6 4 1 1,6 1,6 1 1,6 1 1,6

160 1 1,6 2,5 1 1,6 2,5 1 1,6 1,6 1 1,6 1 1,6

PBD 100 1,6 1,6 4 1,6 1,6 4 1,6 1,6 1,6 1,6 1,6 1,6 ×

160 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 1,6 ×

PMD 100 1,6 1,6 4 1,6 1,6 4 1,6 1,6 1,6 1,6 1,6 1,6 ×

160 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 2,5 1,6 1,6 1,6 ×

PMX 100 1 1,6 4 1 1,6 4 1 1,6 1,6 1 1,6 1 ×

160 1 1,6 2,5 1 1,6 2,5 1 1,6 1,6 1 1,6 1 ×

PMX-E/G* 160 × × × × × × × 1,6 × × × × ×

PBR 100 25 25 25 25 25 25 25 25 25 25 25 25 25

160 25 25 25 25 25 25 25 25 25 25 25 25 25

PBT 100 16 16 16 16 16 16 16 16 16 16 16 16 16

160 16 16 16 16 16 16 16 16 16 16 16 16 16

PPB*** 96x96 1 1,6 4 1 1,6 4 1 1,6 1,6 1 1,6 1 1,6

144x144 1 1,6 4 1 1,6 4 1 1,6 1,6 1 1,6 1 1,6

72x144 1 1,6 2,5 1 1,6 2,5 1 1,6 × 1 1,6 × 1,6

TYPEcase

dimensions MINIMUM RANGE (in mbar)PCX* 160 × × × × × × × 10 × × × × ×

PMX 100 40 100 250 40 100 250 40 100 100 40 100 × ×

160 40 100 250 40 100 250 40 100 250 40 100 × ×

PMX-E/G* 160 × × × × × × × 40 × × × × ×

PMD 160 40 100 250 40 100 250 40 100 100 40 100 × ×

PPC* 144x144 × × × × × × × 10 × × × × ×

* PCX, PPC and PMX-E/G only possible with inductive "INTERVALL" Contact type : I-intervall × NOT POSSIBLE** Only possible on one pointer

*** Only possible with stainless steel bourdon tube

PAGE 32

CONTACT DEVICES FOR PRESSURE GAUGESZEAL BUILT-IN EXECUTION (HZ = contact device under the dial)

DIN16085/16196 Switch function in clockwise direction EXTRA COSTSTYPE CASE DIMENSIONS (in mm)

STANDARD CONTACT (=10W/~18VA), TYPE: S Ø 100 Ø 160 96 x 96 144 x 144 72 x 144

S -1 contact closes

S -2 contact opens

S -3 single change-over contact (SPDT)

S -11 1st contact closes, 2nd contact closes

S -12 1st contact closes, 2nd contact opens

S -21 1st contact opens, 2nd contact closes

S -22 1st contact opens, 2nd contact opens

S- xx+GS double acting contact with separate circuits

S -33 double change-over contact (DPDT) N.A.

S -33+GS double change-over contact (DPDT) separate circuits N.A.

S -xxx triple acting contact, 1=closes, 2=opens N.A.

S -xxxx quadruple acting contact, 1=closes, 2=opens O.D. O.D. O.D. O.D. N.A.

MAGNETIC CONTACT (=30W/~50VA), TYPE: M Ø 100 Ø 160 96 x 96 144 x 144 72 x 144

M -1 contact closes

M -2 contact opens

M -3 single change-over contact (SPDT)

M -11 1st contact closes, 2nd contact closes

M -12 1st contact closes, 2nd contact opens

M -21 1st contact opens, 2nd contact closes

M -22 1st contact opens, 2nd contact opens

M -xx+GS double acting contact with separate circuits

M -33 double change-over contact (DPDT) N.A.

M -33+GS double change-over contact (DPDT) separate circuits N.A.

M -xxx triple acting contact, 1=closes, 2=opens N.A.

M -xxxx quadruple acting contact, 1=closes, 2=opens O.D. O.D. O.D. O.D. N.A.

MICROSWITCH CONTACT (~220V/3A), TYPE: Q Ø 100 Ø 160 96 x 96 144 x 144 72 x 144

Q -3 single change-over contact (SPDT) N.A.

Q -33 double change-over contact (DPDT) N.A.

INDUCTIVE CONTACT (=8V, Ri=1 kohm, EEx ib IIC T6), TYPE: I Ø 100 Ø 160 96 x 96 144 x 144 72 x 144

I -1 contact closes (operating current)

I -2 contact opens

I -x+SN single contact with safety oscillator (SN)

I -11 1st contact closes, 2nd contact closes

I -12 1st contact closes, 2nd contact opens

I -21 1st contact opens, 2nd contact closes

I -22 1st contact opens, 2nd contact opens

I-intervall INTERVALL (for relay WE-77/Ex-IR) N.A. N.A. N.A.

I-xx+SN double contact with safety oscillator (SN)

I-xxx triple acting contact, 1=closes, 2=opens O.D. O.D. O.D. O.D. N.A.

PNEUMATIC CONTACT, TYPE: P Ø 100 Ø 160 96 x 96 144 x 144 72 x 144

P -1 contact closes

P -2 contact opens "0" = 0.2 bar, "1" = 1 bar N.A.

P -12 1st contact closes, 2nd contact opens N.A. P -21 1st contact opens, 2nd contact closes N.A. N.A. N.A.

PAGE 33

PRESSURE GAUGE WITHLOW HYSTERESIS BUILT-IN MICROSWITCH TYPE Q

1

ZEAL TYPE Q-3 Hz and Q-33 Hz STANDARD MODEL

INSTRUMENT : class 1 MINIMAL RANGE : 1,6 bar ELECTRICAL CONNECTION : cable junction box

HYSTERESIS : max. 1% up and down SETPOINT(S) : from outside WINDOW : PMMA - plexiglass POINTER : micro adjustable CONTACT POINTER(S) : first red, (second yellow) ELECTRICAL SWITCH CAPACITY

125 Vac : 5A (ind. load 0.1A)

250 Vac : 3A (ind. load 0.1A)

DC 30 V : 5A (ind. load 0.1A)

DC 125 V : 0.4A

Class 1 and 5 Amp!! DC 250 V : 0.2A

CASE DIAMETER ( Ø in mm)CONTACT TYPE TYPE SWITCH FUNCTION 100 160

Q - 3 Hz SINGLE

Q - 33 Hz DOUBLE

OPTION EXTRA COSTS

Lx LIQUID FILLED CASE ONDINA O.D. O.D.

SETPOINT FIXED SETPOINT WITHOUT SETPOINT(S) ADJUSTMENT 0 0

PAGE 34

2 1 3

2 1 3 5 4 6

ADD-ON UNITS WITH ELECTRICAL CONTACTS FOR PRESSURE GAUGESADD-ON UNIT (contact device on top of dial) with PG cable conduit and 1500 mm cable

DIN16085/16196 Switch function in clockwise direction EXTRA COSTSTYPE CASE DIMENSIONS (in mm)

STANDARD ADD-ON CONTACT (=10W/~18VA), TYPE: S Ø 100 Ø 160 S -1 contact closes

S -2 contact opens

S -3 single change-over contact (SPDT)

S -11 1st contact closes, 2nd contact closes

S -12 1st contact closes, 2nd contact opens

S -21 1st contact opens, 2nd contact closes

S -22 1st contact opens, 2nd contact opens

S- xx+GS double acting contact with separate circuits

S -xxx triple acting contact, 1=closes, 2=opens

MAGNETIC ADD-ON CONTACT (=30W/~50VA), TYPE: M Ø 100 Ø 160 M -1 contact closes

M -2 contact opens

M -3 single change-over contact (SPDT)

M -11 1st contact closes, 2nd contact closes

M -12 1st contact closes, 2nd contact opens

M -21 1st contact opens, 2nd contact closes

M -22 1st contact opens, 2nd contact opens

M -xx+GS double acting contact with separate circuits

M -xxx triple acting contact, 1=closes, 2=opens

INDUCTIVE ADD-ON CONTACT (=8V, Ri=1 kohm, EEx ib IIC T6), TYPE: I Ø 100 Ø 160 I -1 contact closes (operating current)

I -2 contact opens

I -x+SN single contact with safety oscillator (SN)

I -11 1st contact closes, 2nd contact closes

I -12 1st contact closes, 2nd contact opens

I -21 1st contact opens, 2nd contact closes

I -22 1st contact opens, 2nd contact opens

I -xx+SN double contact with safety oscillator (SN)

OPTIONS FOR ELECTRICAL CONTACTS OPTIONS DESCRIPTION Ø 100 Ø 160 96 x 96 144 x 144 72 x 144 OIL FILLING for HZ electrical contacts: only for AISI304/1.4301 cases N.A. N.A. N.A.

CABLE Cable connected to junction box for HZ electrical contacts First 1500 mm: per 1000 mm extra:

MSR-010 Protection relay for single acting contacts (supply 220Vac)

MSR-020 Protection relay for double acting contacts (supply 220Vac)

WE 77/Ex-1 Protection relay for single inductive contacts Eex ia ib IIC

WE 77/Ex-2 Protection relay for double inductive contacts Eex ia ib IIC

BUILT-IN TRANSMITTER DEVICES FOR PRESSURE GAUGES BUILT-IN EXECUTION (HZ) C.W. CABLE JUNCTIONBOX

EXTRA COSTSTYPE DESCRIPTION CASE DIMENSIONS (in mm)

MECHANICAL TRANSMITTER DRIVEN BY POINTER Ø 100 Ø 160 96 x 96 144 x 144 72 x 144 RT43 potentiometer with 4-20mA/3-wire output N.A. RT03 potentiometer with 0-20mA/3-wire output N.A. R potentiometer with 0-100 ohm/3-wire output N.A. BUILT-IN TRANSMITTER (SPAN: min. 1.6 bar (max. 1400 bar)) Ø 100 Ø 160 96 x 96 144 x 144 72 x 144 PT2 4-20 mA, 2-wire, +13..+35Vdc

PT3 0-20 mA, 3-wire, +13..+35Vdc

PTV 0-10 Vdc, 3-wire, +13..+35Vdc

PT2-EX 4-20mA/2-wire Ex-proof transmitter (Eex-ia-IIC-T4..T6)

PAGE 35

For further information on our products or services, please contact Our Distributer

The Gauge of Quality ZEAL

18-A, 1st Floor, Jalan MJ/ 7, Medan Maju Jaya,7th Mile Off Jalan Klang Lama, 46000 Petaling Jaya,Selangor, Malaysia.Tel : 603- 77843918, 77840053, Fax : 603- 77844135E-mail : [email protected] , [email protected] : www.anslabzeal.com

ANSARI AGENCIES SDN.BHD.Distributer :

Documents

PRECISION “HEAVY DUTY” PRESSURE GAUGES · STANDARD PRESSURE GAUGES: PBX pressure gauge with bourdon tube 3 PBX-BI ... If required, calibration certificates from an independent