pr1me FX - Tempo...2017/10/30 · The pr1me-FX fixture can retract up to 1/2” for every 1’ module, as shown in Figure 12 and Figure 13, by removing telescoping spacers, grabbing

06025 REV.A 10-30-17 ECN-1508 Page 1 of 5

1961 McGaw Ave. • Irvine, CA 92614 • (949) 442-1601 • tempollc.com

ELECTRICAL RATINGS

pr1me-FX Products are High Voltage,

Operating at 120/277VAC

REQUIRED HARDWARE

1) Power Feed Cable (PFpFX-F-36) & (PFpFX-M-36)

2) Mounting Hardware, screws provided Surface mount (pFX-SM)

HARDWARE PROVIDED BY OTHERS:

1) Laser Level

2) Power tools

3) Hand tools

OPTIONAL HARDWARE

1) Jumper Feed Cable (JFpFX-JF-12)

NOTE: For maximum pr1meFX lengths, please refer to Specification Sheet

WARNING:Read and understand these instructions before installing. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Turn off main power supply before you start installing pr1meFX.

Ratings, Hardware and Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3-5

PFpFX-F-36

JFpFX-JF-12

PFpFX-M-36

pFX-SM

!

INSTALLATION INSTRUCTIONS

IMPORTANT: Before installing the pr1me-FX be sure to install Tempo Surge Suppression Device (SSD-120/SSD-277) to every branch circuit to validate warranty.

pr1me FXNEW COVE CONSTRUCTION AND EXISTING COVES INTEGRAL POWER SYSTEM

06025 REV.A 10-30-17 ECN-1508 Page 2 of 5



INSTALLATION GUIDELINES

AA

B

LRV of .85recommended for ceilings

LRV of .80 recommended for walls & cove

• 8” Minimum• 12” to 24” Optimum• 30” maximum

3” Minimum (No Max)

B

TOP EDGE OF FIXTURE MOUNTING RAIL MUST BE IN LINE WITH TOP EDGE OF COVE

FOR OPTIMUM PERFORMANCE AND UNIFORM LIGHT WITHOUT HOT SPOTS AT ENDS AND CORNERS LEAVE A SPACE OF 9 INCHES BETWEEN WALL AND EDGE OF FIXTURE. (MIN 6” / MAX 12”)

9” (min 6” / max 12”)

9” (min 6” / max 12”)

9” (min 6” / max 12”)

06025 REV.A 10-30-17 ECN-1508 Page 3 of 5


STEP 1

Mounting of pr1meFX track:

Using a laser level, define a reference line for mounting the pr1me-FX track. Place the track on mounting surface according to reference line and secure using wall-dog screws provided, by tool, until secured as shown in Figure 1 and Figure 2.

STEP 1A - DOUBLE FEED IN CENTER OF RUNS

Locating Power Feeds:

Determine where the start of runs will be and drill hole for conduit feed in between runs as shown in Figure 3. Attach mounting rails to the left and right side of conduit hole, 1” apart as shown in Figure 4.


INSTALLATIONIMPORTANT: To achieve proper fixture ground, supplied Tempo Power Feed Cable (PFC) assembly must be used and attached to grounded J-Box. When connecting field wires to PFC wires observe polarity; I.E. White to neutral, Black to Line and Green to ground.

Field Wires To pr1meFX

Figure 1 Figure 2

Figure 4Figure 3

06025 REV.A 10-30-17 ECN-1508 Page 4 of 5


STEP 1B - SINGLE FEED AT END OF RUNS

Locating Power Feeds:

Drill hole a far left of run, 1” to 3” from end of run. Use Female power feed cable as shown in Figure 5. Drill hole a far right of run, 1” to 3” from end of run. Use Male power feed cable as shown in Figure 6.

STEP 2

Mounting pr1meFX onto track:

Place pr1me-FX on the mounting track by placing the fixture over the mounting track making sure to push the bottom side of the fixture on the clip hook until engaged onto the lip , as shown in Figure 7. Once first hook is engaged, carefully push the fixture so that the second clip hook engages to the top of the pr1me-FX fixture, as shown in Figure 8.


INSTALLATION

Figure 7 Figure 8

Figure 5

NOTE: Hole for conduit can be drilled through the rail as needed.

Conduit Bushing is optional

Figure 6

06025 REV.A 10-30-17 ECN-1508 Page 5 of 5



INSTALLATION (continued)

STEP 3

Connecting power to the pr1meFX:

Connect the female connector on the PFC to the male connector on the Pr1me-FX until clips are engaged, as shown in Figure 9.

Note: When connecting female to male connector ensure that the guide is inserted correctly into the guide hole for proper connection. As shown in Figure A.

Connecting fixture to fixture:

The pr1me-FX can be joined to other pr1me-FX products by inserting male connector and terminating to the female connector to the next fixture, as shown in Figure 10 and Figure 11.

STEP 4 (OPTIONAL)

Retracting Fixture:

The pr1me-FX fixture can retract up to 1/2” for every 1’ module, as shown in Figure 12 and Figure 13, by removing telescoping spacers, grabbing both fixtures and carefully pulling them together. Use this feature to fit the fixture into odd length areas, as shown in Figure 14.

Figure 9

Figure 10

Figure 12 Figure 14

Figure A

Figure 11

Figure 13

WARNING:

Blue protective film is used only to protect pr1meFX during construction, drywall and painting. Peel off protective film after all painting is completed.

Never power fixtures with blue protective film on pr1meFX. This can cause permanent damage from overheating.

Documents

pr1me FX - Tempo...2017/10/30 · The pr1me-FX fixture can retract up to 1/2” for every 1’ module, as shown in Figure 12 and Figure 13, by removing telescoping spacers, grabbing