1
Power Supply 90 VDC CEC015012000090 SPECIFICATIONS Input: 120 VAC, 50/60 Hz single phase, 170 VA max Output: 90 VDC nominal, 1.25 Amps max (Full wave rectified, unfiltered and unregulated.) INSTALLATION • Connect clutch or brake lead wires to terminals 2 and 8. • Connect clutch or brake leads of second unit (if used) to terminals 3 and 6. • Connect control switch (supplied by customer) to common terminal 7. Connect remaining switch positions to terminals 3 and 8 as shown. Note: Switch must have a 120 VAC, 10 AMP (inductive) rating. • Connect “hot” wire of 120 VAC line to terminal 1 and neutral wire of 120 VAC to terminal 5. APPLICATION This power supply is suitable for use with Carlyle Johnson’s EMA, EPC, FEA, FEB, HTB, HBB, EMB, JEM, JEB, and SAB products. WARNING • Make certain all power is off before attempting to install this unit. • Do not connect output lead wires to ground as it will result in damage to the unit. 291 Boston Turnpike, Bolton, CT 06043 Main Phone: 860-643-1531 FAX: 860-646-2645 www.cjmco.com 6 5 4 3 7 8 1 2 OCTAL SOCKET ( – ) ( + ) ( + ) ( – ) 120 VAC INPUT L1 L2 NEUTRAL HOT SWITCH (CUSTOMER SUPPLIED) 90 VOLT CLUTCH 90 VOLT BRAKE Power Supply 90 VDC - Rev 05/2014

Power Supply 90 VDC - Carlyle Johnson Machine Co. Supply 90 VDC CEC015012000090 SPECIFICATIONS Input: ... 10 AMP (inductive) ... with Carlyle Johnson’s EMA, EPC, FEA, FEB, HTB, HBB,

  • Upload
    lydung

  • View
    230

  • Download
    9

Embed Size (px)

Citation preview

Page 1: Power Supply 90 VDC - Carlyle Johnson Machine Co. Supply 90 VDC CEC015012000090 SPECIFICATIONS Input: ... 10 AMP (inductive) ... with Carlyle Johnson’s EMA, EPC, FEA, FEB, HTB, HBB,

Power Supply90 VDCCEC015012000090

SPECIFICATIONS

Input: 120 VAC, 50/60 Hz single phase, 170 VA max

Output: 90 VDC nominal, 1.25 Amps max

(Full wave rectified, unfiltered and unregulated.)

INSTALLATION

• Connect clutch or brake lead wires to

terminals 2 and 8.

• Connect clutch or brake leads of second unit

(if used) to terminals 3 and 6.

• Connect control switch (supplied by customer)

to common terminal 7. Connect remaining

switch positions to terminals 3 and 8 as

shown. Note: Switch must have a 120 VAC,

10 AMP (inductive) rating.

• Connect “hot” wire of 120 VAC line to terminal

1 and neutral wire of 120 VAC to terminal 5.

APPLICATION

• This power supply is suitable for use

with Carlyle Johnson’s EMA, EPC, FEA,

FEB, HTB, HBB, EMB, JEM, JEB, and

SAB products.

WARNING

• Make certain all power is off before attempting

to install this unit.

• Do not connect output lead wires to ground as

it will result in damage to the unit.

291 Boston Turnpike, Bolton, CT 06043 Main Phone: 860-643-1531 • FAX: 860-646-2645

www.cjmco.com

6 5 4 3

7 8 1 2

OCTALSOCKET

( – )

( + )

( + )

( – )

120 VACINPUT

L1

L2

NEUTRAL

HOT

SWITCH(CUSTOMERSUPPLIED)

90 VOLTCLUTCH

90 VOLTBRAKE

Power Supply 90 VDC - Rev 05/2014

Power Supply 90 VDC final 2014_Layout 1 5/22/14 4:06 PM Page 1