Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
- 2 types of beam angle by extrude lens
- 12 kinds of length variation
- Max. connectable length is 9 m
- 4 Color variations
- Easy dimming with 24 VDC low voltage power supply
- High efficiency LED
Power LEDs Line IP65
L-ELA6K2
CIEColor management
Outdoor Rigid Light
Power LEDs Line IP65
L-ELA6K2Outdoor Rigid Light
Jaipur City PalaceLocation: IndiaLighting design: Design Matrix
The Prince Gallery Tokyo KioichoLocation: JAPANArchitect office: Nikken Sekkei LtdInterior design: Rockwell Group, EuropeLighting design: Lighting Planners AssociatesConstruction: KAJIMA CORPORATION / TEKKEN CORPORATION / Kumagai Gumi Co.,Ltd. ConsortiumPhoto: TOSHIO KANEKO
EMPIRE Prestige Causeway BayLocation: Hong KongClient: Asia Standard Hotel Group Ltd.Interior Design: atelier ikebuchi
Application
Balcony and building facade which placed from where does not get direct sunshine
Bathroom
Facade
Small dimention lighting with extrusion lens for grazing effect for outdoor
156 L-ELA6K2 | Power LEDs Line IP65
* mm
* mm
2 types of beam angleby extrude lens
Because of 120° light distribution, the scallop does not come out, even if the distance from the wall is less than 50mm. 35°type is suitable for grazing effect, 60°type is for wider effect. Highly recommended to use 150mm from the wall, in order to spread the light smoothly.
12 kinds of length variation
120 mm increments, min.125mm and max. 1445 mm can be used for complicated shape of facade.
High efficiency LED
Achieved 19.8 W/m, 1600 lm/m and 79 lm/W using Nichia high efficiency LED package.
Lifted mounting clip for preventing invasion of rain water
4 Color variations
4000K, 3500K, 3000K, 2700K
Power LEDs Line IP65
300mm200mm100mm50mm0mm
L :60°× 120°
N :35°× 120°
×
transverse direction longitudinal direction
120°35° 60°
IP67 connector
Heatproof fluororesin cable covered with weather resistance coverLine part : Encapsulated by silicon between aluminum heatsink and extrusion lensEnd part : Encapsulated by silicon around cable, end cap and silicon bush for cablePolycarbonate protection cover covered by steel wire
Comparison of the distance from wall
Advanced waterproofing function design
MADE IN JAPAN
Easy dimming with 24 VDC low voltage power supply
Dimmable by any signal such as 0 - 10 V, DMX, DALI, etc, if you use an adaptive dimming driver, with simple wiring. Ideal for dimming the whole in synchronization. Although it is unsuitable for design that requires individual control.
Max. connectable length is 9 m
Recommended where the power supply installation location and the light fixture location are apart from each other.
Ou
tdo
or
Rig
id Lig
ht
Ou
tdoor
157
L-ELA
6K
2 IP
65
Power LEDs Line IP65 | L-ELA6K2
Line G
raze IP67 | E
FRO
IP65 | P
ow
er LED
s Line IP
65 | LE
Ds B
ar IP65 | LE
Ds Lin
e Hi IP
67
L±3100
φ4
2236
14.2
100 26
13 35
L±3100
φ42236
14.2 35
Power LEDs Line IP65
L - ELA6K2 - * * * * - 24C - P Length code Light source color Beam angle
Model No.
40 : 4000K35 : 3500K30 : 3000K27 : 2700K
L :60°× 120°N :35°× 120°
012024036048060072
084096108120 132144
SpecificationLength code 048 096 144Model No. Both ends lead wire L-ELA6K2-048J**-24C-P L-ELA6K2-096J**-24C-P L-ELA6K2-144J**-24C-P
One end lead wire L-ELA6K2-048E**-24C-P L-ELA6K2-096E**-24C-P L-ELA6K2-144E**-24C-PPower consumption 9.6W/485mm 19.2W/965mm 28.8W/1445mmLamp fitting length (L) 485mm 965mm 1445mmWeight 190g(J) / 178g(E) 360g(J) / 341g(E) 530g(J) / 504g(E)Luminaire efficacy (2700K) 79.2 lm/W 79.2 lm/W 78.8 lm/WLight source color ○ = Device inventory * = Equivalent
40 4000K ○ 820 lm ○ 1640 lm ○ 2460 lm
35 3500K ○ 800 lm ○ 1610 lm ○ 2410 lm
30 3000K ○ 770 lm ○ 1550 lm ○ 2320 lm
27 2700K ○ 760 lm ○ 1520 lm ○ 2270 lm
Contact us about 5000K since they are made-to-order and have a Minimum Order Quantity.
Spec may be subject to change without announcement.The optical data provided on the each product pages are for reference only; the data values are not guaranteed. Please use as reference materials for your planning.
General SpecificationInput voltage DC24V
Environment In & Outdoors (no condensation) IP65
Max. sets connectable 9m
Ambient temperature / humidity -5~40°C 25~95%RH (no condensation)Storage temperature / humidity -15~55°C 25~85%RH (no condensation)Material (body) Aluminium, Polycarbonate
Attachments -
Option parts End clip, Power supply cable, Joint cable
Dimmable ○Power Supplies Required
COO Japan
External dimensions
Both ends lead wire
One end lead wire
Front view
Front view
Cross section view
Cross section view
Max. connectable length per power supplyPower LEDs Line IP65
Normal operation Power supply
~ 1.7m 50W switching power supply
~ 3.5m 100W switching power supply
~ 5.2m 150W switching power supply
Size VariationLength code 012 024 036 060 072 084 108 120 132Power consumption 2.4W 4.8W 7.2W 12.0W 14.4W 16.8W 21.6W 24.0W 26.4WLamp fitting length (L) 125mm 245mm 365mm 605mm 725mm 845mm 1085mm 1205mm 1325mm
Lead wire
J : Both ends lead wireE : One end lead wire
Do not cut the lead wire of outdoor product at a job site. Please do appropriate treatment for the lead wire and connector of the terminal of outdoor LED fixture.
- water directly fall on or pooled- the sunlight directly shines on- liquids including chroline or chemicals fall on- high temperature and high humidity such as saunas and public bath- coastal areas which are affected by sea spray
Caution:
Prohibited installation places:
Outdoor Rigid Light
Light Intensity
L-ELA6K2-096J(E)27N-24C-P
1
2
3
4
37°59°
293
130
73
1172
20(lx)
50100200500
1000
1 102 23m 3
1/2 illuminance angle
Ra 83
Ra 83
Ra 83
Ra 83
L-ELA6K2 | Power LEDs Line IP65158
CIEColor management
ELA6K2
33
40
2310
φ4.2
End clip Option Parts
Model No : ELA1-P-FE2 pcs/1 bag
Optional parts
Top view
front view side view
40
23
For vertical installation or installing in a placewith strong wind and rain.
Power supply cable EPYC *mm Option Parts Required
Top view
Top view
Joint cable EECC *mm Option Parts
Check the label on the DC + side for polarity.
40
20
4.3
6.6
L 26 14
13
(+ side)
1614.2
14
13
6.6
36 L 26
Front view
Front view
Side view
Side view
*(Length:mm) 500 1000 2000 4000
Model No. EPYC220-805-K EPYC220-810-K EPYC220-820-K EPYC220-840-K
*(Length:mm) 500 1000 2000 4000 6000
Model No. EECC220-805 EECC220-810 EECC220-820 EECC220-840 EECC220-860
Ou
tdo
or
L-ELA
6K
2 IP
65R
igid
Ligh
t O
utd
oor
Power LEDs Line IP65 | L-ELA6K2
Line G
raze IP67 | E
FRO
IP65 | P
ow
er LED
s Line IP
65 | LE
Ds B
ar IP65 | LE
Ds Lin
e Hi IP
67
159
Installing the product
Minimum size for construction
Please keep the following size in order to avoid the temperature increase of the lamp.
Any size that is smaller than the following may shorten the lamp’s life.
Cautions¥ Make sure that the installation site is flat.
¥ Before the construction, make sure to remove from the installation site any oil content, water drop, dust and so on.
¥ When installing the product downward or in a vertical direction, pay full attention in order to avoid dislocation, damage due to a fall and so on.
¥ Do not scratch or incise the lead wire. The waterproof performance will be lost.
¥ Make sure to insert the connector until it is completely locked. Otherwise it can lead to the lowering of the waterproof performance and contact failure.
¥ Do not remove the spring for fixing the protective cover. Even on the LED, shading of the light is hardly caused.
Mounting screw
Mounting clip
(installed, slidable)
Option parts:End clip
(ELA1-P-FE)
Screw hole of
4.2mm in diameter
Mounting screw
(round head screw M3.1 x 16) Power source side
Feed side
Screw hole of 4.2mm
in diameter
Fix the lamp on the installation site with the attached
Mounting screws (round head screw M3.1 x 16).
Please attach End clip additionally in order to install in a place
with strong wind and rain , and to prevent misalignment of
mounting position.
Join the connectors. Make sure that they are correctly joined.
Use the one side connector product (L-ELA6K2-*E**-24C-P) for
the end of connection.
Attachment Option Parts
End clip(ELA1-P-FE)
CautionsDo not cut off the connectors to use them. The waterproof
performance will be lost. In order to avoid the exposure
to direct sunlight, hide the connectors behind the lamp,
etc.
CautionsNot suitable to be fixed with a double-sided tape or
adhesive.
Cove lighting Cornice lighting Sideways Sealed (the size is the same for both upward and downward)
Over 45
Over 45
Over 50
Over
10
0
Un
der
12
0
Over
50
Over
50
Un
der
45
Un
der
30
Over 50
※ unit of measure=mm
29 mm
35 mm
L-ELA6K2 | Power LEDs Line IP65160
Connecting to the power supply
■Cables used for connecting LED fixtures and Power supply must be a suitable type and gauge.
■Cables should be joined with suitable terminal block or methods as appropriate to the installation and
operating environment.
Caution: When using a long cable with thin dimension, the resistance of cable will increase. Voltage drop
and heat dispatching may occur and result in brightness decreasing.
Caution: When separating one cable to multiple circuits in the same gauge, the current loading focuses
on the junction of the branch circuit and high temperature will liberate on there.Please consider the
loading of the power supply (quantity of LED fixture) and review the wiring system to avoid the above
problem.
■When connecting the dimmer driver with power supply, unpredicted noise might occur. It is a
characteristic of electronic devices, not a malfunction of the LED fixture.
Please choose an appropriate power supply and consider a place to install. Reducing the loading
factor of LED fixture might improve the noise from the power supply while the noise for the LED
fixtures might be improved by splitting the circuit of LED fixtures into multiple.
System configuration diagram
■ Max. connectable length depends on the wattage of the power supply.
■ Max. length per circuit of Power LEDs Line IP65 is 9 m.
If it exceeds 9 m, please split into multiple circuits.
■ Max. distance from the power supply to the end of LED fixture is 12.2 m.
Circuit 1
LED fixture less than 9mUp to 3.2m
Power supply
DC24V
Option Parts Required
Power supply cable EPYC 500mm, 1000mm, 2000mm, 4000mm(EPYC220-805-K, EPYC220-810-K, EPYC220-820-K, EPYC220-840-K)
Direct horizontal surface light intensity distribution chart
L-ELA6K2-096J(E)40L-24C-P L-ELA6K2-096J(E)40N-24C-P
Light source color 3500KBrightness 210 cdLuminous flux 830 lmColor rendering index Ra 83
Light source color 3500KBrightness 1241 cdLuminous flux 1610 lmColor rendering index Ra 83
Light source color 3000KBrightness 202 cdLuminous flux 800 lmColor rendering index Ra 83
Light source color 3000KBrightness 1195 cdLuminous flux 1550 lmColor rendering index Ra 83
Light source color 2700KBrightness 197 cdLuminous flux 780 lmColor rendering index Ra 83
Light source color 2700KBrightness 1172 cdLuminous flux 1520 lmColor rendering index Ra 83
L-ELA6K2-096J(E)35L-24C-P L-ELA6K2-096J(E)35N-24C-P
L-ELA6K2-096J(E)30L-24C-P L-ELA6K2-096J(E)30N-24C-P
L-ELA6K2-096J(E)27L-24C-P L-ELA6K2-096J(E)27N-24C-P
Light source color 4000KBrightness 213 cdLuminous flux 840 lmColor rendering index Ra 83
Light source color 4000KBrightness 1265 cdLuminous flux 1640 lmColor rendering index Ra 83
1
2
3
4
54°68°
209
93
521 102 23m 3
837
20(lx)
50100200500
1000
1/2 illuminance angle
1
2
3
4
37°59°
316
140
791 102 23m 3
1265
20(lx)
50100200500
1000
1/2 illuminance angle
1
2
3
4
54°68°
205
91
511 102 23m 3
20(lx)
50100200500
1000
821
1/2 illuminance angle
1
2
3
4
37°59°
310
137
771 102 23m 3
20(lx)
50100200500
1000
1241
1/2 illuminance angle
1
2
3
4
54°68°
197
87
49
791
20(lx)
50100200500
1000
1 102 23m 3
1/2 illuminance angle
1
2
3
4
37°59°
298
132
74
1195
20(lx)
50100200500
1000
1 102 23m 3
1/2 illuminance angle
1
2
3
4
54°68°
193
86
48
775
20(lx)
50100200500
1000
1 102 23m 3
1/2 illuminance angle
1
2
3
4
37°59°
293
130
73
1172
20(lx)
50100200500
1000
1 102 23m 3
1/2 illuminance angle
Ou
tdo
or
L-ELA
6K
2 IP
65R
igid
Ligh
t O
utd
oor
Power LEDs Line IP65 | L-ELA6K2
Line G
raze IP67 | E
FRO
IP65 | P
ow
er LED
s Line IP
65 | LE
Ds B
ar IP65 | LE
Ds Lin
e Hi IP
67
161
SANSHO Korea CO.,LTD.韓國三昌商事株式會社KOREA SANSHO SHOJI CO.,LTD.#507, 36, Teheran-ro 87gil, Gangnam-gu, Seoul, 06164, KoreaTel: +82-2-508-2541
Partner Company Korea
Tokyo Japan Regional HQ Akasaka Bldg. 4F, 4-13-13, Akasaka, Minato-ku, Tokyo 107-0052, JapanTel : +81-3-6327-7409 E-mail : [email protected]
Osaka Office Yotsubashinakano Bldg. 3F, 1-1-14, Minamihorie, Nishi-ku, Osaka-shi, Osaka 550-0015, JapanTel : +81-6-6110-7520 E-mail : [email protected]
Group company
Singapore World HQ52A Tanjong Pagar Road, Singapore 088473Tel : +65-6291-2410 E-mail : [email protected]
Hong Kong Marketing OfficeRoom 1801, 18/F, Kwai Hung Holdings Centre, 89 King's Road, North Point,Hong KongTel : +852-2219-8462 E-mail : [email protected]
Dubai Marketing Office5WA 331, DAFZA, Dubai, United Arab EmiratesTel: +971-54-446-0350 E-mail : [email protected]
Group company
Shanghai China mainland Regional HQ : 上海本社Rm.1804, South Building, 300 Xuanhua Rd., Changning District, Shanghai(200050)PRC.Tel : +86-21-5238-9115 E-mail : [email protected]
Beijing Office : 北京分公司Rm.1030 Building102, (Qingnian Rd) Qingniangongshe., Chaoyang North Rd, Chaoyang District, Beijing(100026)PRC.Tel : +86-10-6556-9541 E-mail : [email protected]