16
Portable Basketball System Model 4400S Assembly Instructions & Owners Manual

Portable Basketball System Model 4400S - The Home … may cause system to fail. ... BPP Base Pole Pin 1 W Wheel 2 MUW Multi Use Wrench 1 LS Large Springs 2 ... TPCR Top Pole Cover

  • Upload
    dongoc

  • View
    212

  • Download
    0

Embed Size (px)

Citation preview

Portable Basketball SystemModel 4400S

Assembly Instructions & Owners Manual

2

WARNINGFAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS

INJURY AND / OR PROPERTY DAMAGE. OWNERS MUST ENSURE THAT ALL PLAYERS KNOW AND FOLLOW

THESE RULES FOR SAFE OPERATION OF THE SYSTEM.

See Instruction manual for proper installation and maintenance

BYC SPORTS866-561-0731

• Never hang from the rim or any part of the system including backboard, support braces or net to avoid personal injury.• During play, especially when performing dunk type activities, keep player’s face away from the backboard, rim, and net. Serious injury could occur if teeth/ face come in contact with backboard, rim, or net.• Do not slide, climb, or play on base or pole. Completely fi ll base according to manufacturer’s instructions or the system will tip quickly causing serious personal injury. Never leave system in upright position without fi lling base with weight, as system may tip over causing personnel injury. • When adjusting height or moving system, keep hands and fi ngers away from moving parts.• Do not allow children to move or adjust system.• During play, do not wear jewelry ( rings, watches, necklaces, etc.) Objects may entangle in net.• Surface beneath the base must be smooth and free of gravel or other objects. • Place system on fl at ground, never place on slopes, system may tip over.• Punctures can cause leakage and could cause system to tip over. Keep water and organic material away from pole. Pole can rust and fall• Once a month, check pole and all metal parts for rust. Completely remove rust and repaint with exterior enamel. If rust has penetrated any steel part, replace that part immediately.• Check system before each use for proper ballast, loose hardware, instability, and signs of corrosion and repair before each use. Never play with damaged equipment.• Do not use system during windy or severe weather. System may tip over. Place system in an area protected from the wind or in a area away from property that may be damaged if the system should fall.• Never play on damaged equipment.• When moving system, use two capable adults to prevent system from tipping.• Do not allow water in system to freeze. During sub-freezing weather conditions, add enough non toxic anti-freeze to water to prevent freezing, use sand, or empty water and store system in a safe manner.• While moving system, do not allow anyone to ride on base

3

BEFORE YOU BEGIN!Thank you for purchasing the BYC Sports portable basketballsystem, Model 4400S. Please be sure you have received all

hardware and pieces before you begin assembly.

Save these instructions in the event that manufacturer has to be contacted for replacement parts. If you are missing anything or have received

damaged products, please call us toll free: 1-866-561-0731

SAFETY INSTRUCTIONSFailure to follow these safety instructions may result in serious injury or property damage and will void warranty. Owner must ensure that

all players know and follow these rules for safe operation of the system.

To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly,

read the instructions and identify parts using the hardware identifi er and parts list in this document. Proper and complete assembly, use, and super-vision are essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not

installed, maintained, and operated properly.

• If using a ladder during assembly, use extreme caution.• 2 Capable adults are recommended for this operation.

• Check base daily for leakage. Leaks may cause system to fail.• Assemble and secure pole sections properly. Failure to do so could

cause the pole sections to separate during play or transport.• Minimum operational height is 6’ 6” to the bottom of the backboard

Most injuries are caused by misuse and/or not following instructions.Use caution when using this system.

4

Hardware ListBefore you begin assembly, make sure you have been provided

with all the necessary parts. If you are missing pieces call1-866-561-0731

Items Required For Assembly- NOT INCLUDED -

Adjustable WrenchRubber Mallet300 Lbs Sand

2 Capable Adults

PART DESCRIPTION QTY

MHPR Hardware Pack 1

BG 10 x 56mm Bolt 4

WG 10mm washer 9

LNI 10mm Locking Nut 8

BC 10 x 90mm Bolt 2

CBG 10 x 55mm Carriage Bolt 2

BD 8 x 20mm Bolt 4

CBF 8 x 90mm Carriage Bolt 3

HNM Hand Nut 2

WAW Wheel Axle Washer 2

WH 8 mm Washer 6

LNJ 8mm Lock Nut 3

WA Wheel Axel 2

BPP Base Pole Pin 1

W Wheel 2

MUW Multi Use Wrench 1

LS Large Springs 2

SS Small Springs 2

CR Check Ring 8

5

MUW

BG

BC

BD

CBF

WG

WH

LNI

LNJ

W

WA BPP

CBG

HNM

Hardware Included

WAW

SS

LS

CR

6

Parts ListBefore you begin assembly, make sure you have been provided

with all the necessary parts. If you are missing pieces call1-866-561-0731

PART DESCRIPTION QTY

RBP Round Base Pole 1

RMP Round Middle Pole 1

RTP Round Top Pole 1

BBS Back Board Bracket 1

SSP Side Support Pole 2

BASE Base 1

BB4400S Backboard 1

WN White Net 1

R Rim 1

BP Base Plug 1

BG Base Gasket 1

TPCR Top Pole Cover 1

BPCR Base Pole Cover 1

WL Warning Label 1

HAL Height Adjustment Label 1

INS4400S Instruction Manual 1

7

BASE

WN

R

BPBG

SSP

TPCR

BB4400S

BPCR

BBS

RTP RMP RBP

8

STEP 1 - Attach trim parts to round base pole.

STEP 2 - Attach round base pole to Base

Fig. 1

YOU WILL NEED: A Rubber MalletInsert top pole cover (TPCR) onto top of round top pole (RTP) and tap into place.

Fig. 2

YOU WILL NEED: A Rubber MalletInsert round base pole (RBP) into Base, aline holes in base and round base pole (RBP), insert base pole pin (BPP) through base and round base pole and lock into place.

9

STEP 3 - Attach wheels to base

STEP 4 - Attach side support poles

Fig. 4

YOU WILL NEED: Multi Use Wrench (MUW) Attach side support poles (SSP) to base using (2) bolt (BD), (4) washers (WH), and (2) locknuts (LNJ). Repeat for other side support pole. (hand tighten only at this time) Attach side support poles (SSP) to round base pole (RBP) using bolt (BD), and washer (WH). Repeat for other side. (See fi gure 4) Tighten all hardware. See Fig 4

YOU WILL NEED: A Rubber Mallet Slide wheel axle (WA) through wheel (W). Slide Wheel Axel Washer (WAW) on the Wheel Axel (WA). *This washer should be on the the side closest to the center pole. Snap wheel axle (WA) into groves in base, and lock into place, repeat for other wheel.

CAUTION!Have a helper hold the round base pole while

attaching the side support poles to prevent pole from

falling.

10

STEP 5 - Fill base with sand

YOU WILL NEED:300 Lbs. of Sand. 2 adults needed

One adult needs to lift the back of the base so the base is at about a 45 degree angle. (a block can also be used to help hold up the base) Remove plug and start adding sand through the hole in the base. Carefully lower the base so the round base pole is vertical, continue fi lling the base with

sand until it is just below the fi ll hole.

Be sure the front portion of the base is also fi lled.

Replace base gasket (BG) and base plug (BP) hand tighten plug

Fig. 5

WARNING

Never put the system in an upright position with out proper weight in the base. System may fall over and could cause personal injury

or property damage.

Sand

11

STEP 6 - Attach backboard bracket & rim to backboard

Insert 2 bolts (BC), 4 large spring caps (LSC), 2 large springs (LS), 2 washers (WG), and 2 locknuts (LNI) through top holes of rim and backboard (NOTE: large springs need to be on the top 2 holes. Hand tighten only at this time). Insert 2 bolts (BC), 4 small spring caps (SSC), 2 small springs (SS), 2 washers (WH), and 2 lock-nuts (LNI). **Small springs need to be on the bottom 2 holes****Do not over tighten bolts; only tighten so bolt is fl ush with lock nut.**See Fig 6

Fig. 6

12

STEP 8 - Attach backboard & brackets to pole

YOU WILL NEED: Multi Use Wrench (MUW) & Adjustable WrenchAline holes in top of Round Top Pole (RTP), with holes in Backboard Bracket (BBS) Insert 2 bolts (BC), 2 washers (WG), and 2 locknuts (LNI). See Fig 8**Tighten all bolts in this step.

Fig. 8

STEP 7 - Attach net to rim

Slip loop of net through hook on rim, repeat for all 12 hooks. See Fig 7

Fig. 7

13

STEP 9 - Insert round middle pole into round base pole

YOU WILL NEED: Multi Use Wrench (MUW) & Adjustable WrenchInsert Round Middle Pole (RMP) into Round Base Pole (RBP), align holes, and Insert (2) carriage bolts (CBF) and attach (2) Hand Nuts (HNM). See Fig 9 **Note: Hand Nuts need to be on inside, toward the base. Hand tighten only

STEP 10 - Attach top pole to middle pole

YOU WILL NEED: Adjustable WrenchBe sure that Base pole is at the lowest setting (see step 12). Stand base up so that it is vertical. Using 2 adults, lift backboard and top pole assembly, and carefully set onto Round Middle Pole (RMP). Aline holes, and insert Carriage bolt (CBF) through poles, insert, washer, (WH) and locknut (LNJ). Tighten Lock Nut. See Fig 10

Fig. 10

Fig. 9

14

STEP 11 - Height adjustment

*Adult supervision required!Loosen (2) Hand Nuts (HNM), while 1 adult holds middle pole, 1 adult removes (2) carriage bolts (CBF) raise or lower backboard portion to the desired height, replace (2) carriage bolts (CBF), and (2) Hand Nuts (HNM) and hand tighten. See Fig 11 Caution: Be careful not to pinch fi ngers between poles! Do not Raise system past the 10’ Line!

Fig. 11

15

1.

2.

3.

4.

CARE & MAINTENANCEThe life of your portable basketball system depends on may variables. The weather,

climate, exposure to corrosives, and excessive use, can all contribute to system failure, which may result in property damage or personal injury.

Before each use: Check for loose hardware and tighten as needed. Check all parts for excessive wear and tear, replace any parts that are worn. Inspect the warning sticker for

fading or tears, replace as needed. Check the entire pole for signs of rust, chipped or cracked paint, or scratches. Repair by sanding damaged area, and applying 2 coats of rust preventitive paint. (Follow instructions on paint) If rust has penetrated through the pole,

replace that part immediately. Parts are availble through our customer service department.

To Clean: Only clean the backboard with water, a mild detergent and a soft cloth.Do NOT use any abrasive chemicals or materials on any part of the system.

This will void the warranty!!

MOVING THE SYSTEM

YOU WILL NEED: 2 Adults

1 - Adjust basketball backboard height to the lowest position. 2 - While holding pole, lean basketball system forward until wheels come in to contact with ground.3 - Move basketball system to desired location.4 - Carefully stand pole upright until pole is vertical and base is fl at.5 - Check system for stability.

WARNING

The system must only be moved by 2 adults

capable of handling its weight. Children should not be allowed to move

the system.

16

BYC WARRANTYBYC Sports Portable Basketball System

2-Year Limited WarrantyThe Manufacturer reserves the right to make substitutions to

Warranty Claims if parts are unavailable or obsolete

BYC Sports portable basketball systems are warranted to the original purchaser to be free from defects in material or workmanship for a period of two years from

the date of original retail purchase (a copy of the original dated sales receipt is needed for all warranty claims). Defects, is defi ned as imperfections that impair the use of the product. Defects resulting from missuse, abuse or negligence will

void this warranty. This Warranty does NOT cover the following: improper instal-lation, alterations of any type, vandalism, rusting, scratching, or any other dam-

age caused by normal use, accidental damage, acts of nature, intentional damage, (which includes damage caused from hanging on the rim) , unreasonable use, or any other event beyond the control of the manufacturer will void this warranty.

This warranty is non-transferable, and is limited to the replacement of defective portable basketball equipment. If the equipment is found to be defective within

the terms of this warranty, BYC Sports will replace defective parts at no cost to the purchaser. ( shipping charges are NOT included in this warranty, these are the re-sponsibility of the purchaser) Labor charges or any other related expenses, which

may be needed to replace the defective parts are NOT covered in thiswarranty, and are the responsibility of the purchaser.

Any liability for incidental or consequential damages is excluded to the extent permitted by law. Every attempt is made to manufacture as safe product. The end user assumes all risk of injury resulting from the use of this product. All products are sold on this condition; no representative of the company may alter or waive

this policy, both verbal and written.

This product is intended for RESIDENTIAL use only. BYC Sports is not in any way liable if these products are used in an institution or for commercial use,

which will void this warranty.

This warranty replaces all other warranties, either expressed or implied. BYC Sports or any of its representatives assumes no liability of this product, should

they arise.

ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY ADATED SALES RECEIPT.

BYC Sports VDG Inc.

606 Washington Ave. North, Suite 300Minneapolis, MN 55401

Toll Free Parts line: 866-561-0731