Pneumatics Training System, Model 6081 - Lab-Volt · PDF filePneumatics Applications – PLC expands upon the others with pneumatics applications controlled by PLCs. In Servo Control

LabVolt Series

Datasheet

6081Pneumatics Training System

Festo Didactic

en 120 V - 60 Hz

03/2018

Pneumatics Training System, LabVolt Series, 6081

2 © Festo Didactic

Table of ContentsGeneral Description_______________________________________________________________________2Innovative design ________________________________________________________________________3Virtual Laboratory Equipment_______________________________________________________________3Courseware______________________________________________________________________________3eLearning Systems________________________________________________________________________4Topic Coverage___________________________________________________________________________4Features & Benefits _______________________________________________________________________4List of Available Training Systems ___________________________________________________________5Optional Equipment_______________________________________________________________________5Optional Manual(s) _______________________________________________________________________6Available Training Systems_________________________________________________________________6Equipment Description __________________________________________________________________ 26Optional Equipment Description __________________________________________________________ 65

General DescriptionThe Pneumatics Training System is part of a modular program in pneumatics and its applications. The Pneumatics Training System answers the needs of students in technical institutes, vocational colleges, and university engineering departments, as well as in industry. The training system encourages hands-on learning and is a great addition to any hydraulics and pneumatics lab.

The pneumatics training program is divided into the following subsystems: Pneumatics Fundamentals, Electrical Control of Pneumatic Systems, Pneumatics Applications – PLC (programmable logic controller), Troubleshooting Pneumatic Circuits, Servo Control of Pneumatic Systems, and Sensors.

In Pneumatics Fundamentals, students are introduced to the basic principles and components of pneumatics. Electrical Control of Pneumatic Systems covers electrical control of pneumatic systems with ladder diagrams. Pneumatics Applications – PLC expands upon the others with pneumatics applications controlled by PLCs.

In Servo Control of Pneumatic Systems, students are introduced to servo-controlled pneumatic systems and their associated circuitry. In Troubleshooting Pneumatic Circuits, students develop their skills in troubleshooting. In Sensors, students are introduced to the operating characteristics of six types of photoelectric and proximity sensors.

Most electrical components of the Electrical Control of Pneumatic Systems can be used with the Hydraulics Training Systems, Series 6080, allowing interconnection of the systems to perform more complete functions.


© Festo Didactic 3

Innovative designEngineered for extreme ease of use, the basic system comes with a work surface assembly consisting of a solid metal, universal drip-tray hinged to a perforated, tiltable work surface on which pneumatic components can be mounted.

The work surface can be configured to accommodate a wide variety of space and teaching needs. Lying flat over the drip tray, or tilted at 45°, the work surface provides a large area on which pneumatic components and space-expanding work surfaces can be mounted at any location, either at 0° or 90°.

Mounting and removing components is especially easy with the quick-lock system that secures the component base plate to the work surface.

Although the system is designed to operate atop a regular work table, an optional bench is available to provide mobility and storage space. Mounted on four heavy-duty, swivelling, lockable castors, the bench provides shelving for extra work surfaces and components. Optional dressing panels are also available to fully enclose the bench and provide storage area for components.

The work surfaces may also be linked together for more complete electro-pneumatic/hydraulic circuits. By utilizing the optional work surfaces, exercise setups can be saved.

Two student groups can simultaneously work on a bench when the Work Surface (Dual A-Frame), Model 6301-1, is used. All components meet industrial safety standards, are identified with the proper ANSI symbol, and are equipped with quick-connect fittings.

Virtual Laboratory EquipmentAll components contained in the Pneumatics Fundamentals and Electrical Control of Pneumatic Systems can be

simulated using the Windows®-based Pneumatics Simulation Software (LVSIM®-PNEU), Model 6485. The simulated components can be interconnected and their operation studied, using the same courseware as that used for the real equipment.

CoursewareThe courseware consists of a student manual for each training system. The student manuals are divided into several units, each consisting of a series of hands-on exercises dealing with one of the pneumatics fields. Each exercise provides a clearly stated objective, a discussion, textbook references, a summary of the exercise procedure, a detailed exercise procedure, a conclusion, and a set of review questions.

A ten-question test at the end of each unit allows students to verify what was learned in the unit. Refer to the tables of contents of the manuals for a list of the topics covered in the student manuals.

The instructor guides contain the measurement results as well as the answers for each hands-on exercise of the student manuals, and the answers to the unit test questions.

The courseware also includes a reference textbook, optional instructional DVDs, and courseware figures. These figures are available in the form of transparencies and on CD-ROM. Furthermore, all student manuals and instructor guides are available, as an option, in Job Sheet format.


4 © Festo Didactic

eLearning SystemsThe courseware is also available in three eLearning formats for users who prefer a computer-based approach:

• eSeries, facilitated by the Mind-Sight eLearning System. See Pneumatics Fundamentals eSeries, Model 6486-E, and Advanced Hydraulics eSeries, Model 6486-1.

• SCORM-based, designed to be hosted by a third-party, SCORM 1.2 compliant Management System. See Pneumatics Fundamentals SCORM, Model 6486-F, and Advanced Pneumatics SCORM, Model 6486-2.

• Stand-alone, available on CD-ROM. This format runs on a web browser and does not require any management system. See Pneumatics Fundamentals Stand-Alone, Model 6486-G, and Advanced Pneumatics Stand-Alone, Model 6486-3.

Topic Coverage• Introduction to Pneumatics (components, circuits, laws)• Electrical Control of Pneumatic Systems• PLC-Controlled Pneumatic Applications• Servo Control of Pneumatic Systems• Sensors• Troubleshooting• Estimated Program Duration: 100 hours

Features & Benefits• Equipment

Many work surface options, including an A-Frame top to allow experiments on both sidesLockable storage available


© Festo Didactic 5

1 Price can be calculated as follows: for 1 additional year *7% of total net, for 2 additional years *12% of total net and for 3 additional years *15% of total net. For details and options, contact [email protected].

Industrial-grade components pre-labeled with appropriate circuit symbols, providing learning reinforcementRepositionable components build a foundation of knowledge one device at a time, making it easier to teach circuit assemblyTeachers can create their own circuits to reproduce specific pneumatic applicationsPneumatic trainer engineered for extreme ease of use and durabilityExceeds industrial safety standardsFaulty component package for real-world troubleshooting

• CurriculumInnovative approach that allows interconnection with other products, such as hydraulics, sensors, PLCs, robots, etc.DVDs and transparencies are available to enhance student learningCurriculum available in standard student activity manuals or in job-sheet format (closely representing what a student will see in industry), in PDF format on CD-ROM as a site license. A one-time purchase with no annual renewal fee allows unlimited printingA simulation software program that mirrors 100% of the curriculumRealistic faulty component package instead of a simulated fault approach

List of Available Training Systems

Qty DescriptionModel number

1 Pneumatics Fundamentals _______________________________________________________________ 6081-101 Electrical Control of Pneumatic Systems ____________________________________________________ 6081-201 Servo Control of Pneumatic Systems _______________________________________________________ 6081-401 Pneumatics Fundamentals (Add-On) _______________________________________________________ 6081-901 Pneumatics Fundamentals (with Standard Bench, Unassembled) _______________________________ 6081-A01 Pneumatics Fundamentals (with Lockable Bench, Unassembled) _______________________________ 6081-B01 Pneumatics Fundamentals (with Lockable Bench, Assembled) __________________________________ 6081-C01 Pneumatics Fundamentals (with Lockable Bench, A-Frame, Unassembled) _______________________ 6081-D01 Pneumatics Fundamentals (with Lockable Bench, A-Frame, Assembled) __________________________ 6081-E01 Troubleshooting Pneumatic Circuits _______________________________________________________ 6081-F01 Hydraulics and Pneumatics Applications – PLC (Allen Bradley) _________________________________ 6082-501 Sensors Training System ________________________________________________________________ 6085-00

Optional Equipment


1 Extended Warranty for the Pneumatics Training System ______________________________________ 6081-EW1 Work Surface (A-Frame) _________________________________________________________________ 6301-101 Expanding Work Surface (Large) __________________________________________________________ 6302-001 Expanding Work Surface (Small) __________________________________________________________ 6302-101 Bench (Unassembled) __________________________________________________________________ 6303-101 Dressing Panels (with Lockable Front Door) _________________________________________________ 6303-A01 Bench (Assembled) _____________________________________________________________________ 6303-B01 Bench (with Dressing Panels and Lockable Front Door, Assembled) ______________________________ 6303-C01 Bench (with Dressing Panels and Lockable Doors, Assembled) _________________________________ 6303-D0

1


6 © Festo Didactic

2 Can be used to supply compressed air to the Pneumatics Training Systems.


1 Bench (with Dressing Panels and Lockable Doors, Unassembled) _______________________________ 6303-E01 Storage/Work Surface __________________________________________________________________ 6309-001 Air Compressor _______________________________________________________________________ 6410-B01 Directional Control Valve (Roller-Lever Operated) ____________________________________________ 6431-001 Advanced Pneumatics - eSeries ___________________________________________________________ 6486-101 Pneumatics Fundamentals - eSeries _______________________________________________________ 6486-E01 Instructional DVD - Introduction to Fluid Power _____________________________________________ 93840-101 Instructional DVD - Fluid Power Technology at Work _________________________________________ 93841-101 Instructional DVD - Pumps, Lines, Filters ___________________________________________________ 93842-101 Instructional DVD - Control Mechanisms ___________________________________________________ 93843-101 Instructional DVD - Actuators ____________________________________________________________ 93844-10

Optional Manual(s)


1 Pneumatics Manuals in Exercise Format (Manuals on CD-ROM) ________________________________ 31290-A01 Pneumatics Fundamentals (Courseware Figures on Transparencies) ____________________________ 31290-M01 Electrical Control of Pneumatic Systems (Courseware Figures on Transparencies) _________________ 31300-M01 Pneumatics Applications – PLC (Student Manual) ___________________________________________ 31726-M01 Servo Control of Pneumatic Systems (Student Manual) _______________________________________ 31977-M01 Sensors (Student Manual) ______________________________________________________________ 32606-M01 Courseware figures on CD-ROM – Pneumatics Training System (all subsystems) (Student Manual) ___ 33562-M01 Pneumatics Manuals in Job Sheet Format (Manuals on CD-ROM) _______________________________ 39900-A0

Available Training Systems

Pneumatics Fundamentals6081-10

The Pneumatics Fundamentals training system introduces students to the basic principles and components of pneumatics.

No air compressor is supplied with the training system. Refer to the training system specifications for the compressed air supply requirements.

All components in this training system

can be simulated using the Windows®-based Pneumatics Simulation

Software (LVSIM®-PNEU), Model 6485. The simulated components can be interconnected and their operation studied using the same courseware as that used for the real equipment.

The courseware is also available in eLearning format for users who prefer computer-based approach.

2


© Festo Didactic 7

List of Equipment


1 Work Surface __________________________________________________________________________ 6301-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-101 Long Line _____________________________________________________________________________ 6492-00

List of Manuals

DescriptionManual number

Pneumatics Fundamentals (Student Manual) ___________________________________________________ 31290-00Pneumatics (Instructor Guide) _______________________________________________________________ 31290-10Industrial Pneumatic Technology (Student Manual) ______________________________________________ 31290-80

Table of Contents of the Manual(s)

Pneumatics Fundamentals (Student Manual) (31290-00)• 1-1 Familiarization with the Lab-Volt Pneumatics Trainer• 1-2 Introduction to Pneumatics• 1-3 Air Conditioning and Distributing Equipment• 2-1 Pressure vs Force Relationship• 2-2 Pressure vs Volume Relationship• 2-3 Pressure Drop vs Flow Relationship• 2-4 Vacuum Generation• 3-1 Directional Control Valves• 3-2 Directional and Speed Control of Cylinders• 3-3 Cylinders in Series• 3-4 Cylinders in Parallel• 4-1 Indirect Control Using Pilot-Operated Valves• 4-2 Pneumatic Motor Circuits• 4-3 Pneumatic Motor Performance

Additional Equipment Required to Perform the Exercises


8 © Festo Didactic

3 Optional product training. Price provided on demand. For details and options, contact [email protected] Installation and basic commissioning of the equipment in your classroom. Installer fees (flight, accommodation...) must be added to the price. The product (box(es) and/or pallet(s)) must already be in the classroom or extra charges will apply. For details or other options, contact

"[email protected]".


1 Training on Pneumatics Fundamentals, 1.1 days ____________________________________________ 31290-TF

Optional Equipment


1 Installation and Commissioning of a 6081-1 System _________________________________________ 60811-IC

System SpecificationsParameter Value

Compressed Air Supply Requirements

Flow Rate 90 L/min (3.2 SCFM) approx.

Pressure 630 kPa (90 psi) approx.

Physical Characteristics

Required Space (H x W x D) 1500 x 1800 x 1500 mm (60 x 72 x 60 in)

Net Weight 29.4 kg (64.5 lb)

Electrical Control of Pneumatic Systems6081-20

The training system Electrical Control of Pneumatic Systems introduces students to the electrical control of pneumatic systems.

Most of the electrical components of this training system can also be used with the Hydraulics Training Systems, Series 6080, allowing interconnection of both systems to perform more complete functions.


can be simulated using the Windows®-based Pneumatics Simulation


The courseware is also available in eLearning format for users who prefer a computer-based approach.

List of Equipment


1 Expanding Work Surface (Large) __________________________________________________________ 6302-001 DC Power Supply ______________________________________________________________________ 6360-A02 Push-Button Station ____________________________________________________________________ 6361-001 Limit-Switch Assembly __________________________________________________________________ 6362-00

3

4


© Festo Didactic 9

5 Installation and basic commissioning of the equipment in your classroom. Installer fees (flight, accommodation...) must be added to the price. The product (box(es) and/or pallet(s)) must already be in the classroom or extra charges will apply. For details or other options, contact



2 Relay ________________________________________________________________________________ 6363-001 Time-Delay Relay / Counter ______________________________________________________________ 6364-002 Pilot-Lamp Station ______________________________________________________________________ 6365-002 Magnetic Proximity Switch _______________________________________________________________ 6371-001 Diffuse Reflective Photoelectric Switch _____________________________________________________ 6372-001 Multimeter ____________________________________________________________________________ 6394-A01 Directional Control Valve (5/3-Way Double-Solenoid Valve) ____________________________________ 6423-001 Single Solenoid-Actuated Directional Control Valve ___________________________________________ 6424-001 AND Function Valve (Dual-Pressure Valve) __________________________________________________ 6425-001 Shuttle Valve (OR Function Valve) _________________________________________________________ 6426-001 Quick Exhaust Valve ____________________________________________________________________ 6427-001 Pressure Regulator _____________________________________________________________________ 6428-001 Pressure Switch ________________________________________________________________________ 6470-001 Tees _________________________________________________________________________________ 6490-001 Connection Leads (4 Lengths) ____________________________________________________________ 6491-A0

Manual


Electrical Control of Pneumatic Systems (Student Manual) ________________________________________ 31300-00


Electrical Control of Pneumatic Systems (Student Manual) (31300-00)• 1-1 Familiarization with the Equipment• 2-1 Basic Electricity• 2-2 Ladder Diagrams• 2-3 Basic Electrically Controlled Pneumatic Circuits• 2-4 Basic AND and OR Logic Function Circuits• 3-1 Basic Memory and Priority Electropneumatic Circuits• 3-2 Multi-Pressure Systems• 3-3 Sequencing Pneumatic Circuits• 3-4 Time-Delay Electropneumatic Applications• 4-1 Pneumatic Actuator Deceleration Circuits• 4-2 Counting of Actuator Cycles• 4-3 Industrial Drilling System and Safety Circuits• 4-4 Garbage Compactor Simulation Circuit• 5-1 Troubleshooting Electrical Control Circuits• 5-2 Troubleshooting Electrically Controlled Pneumatic Systems

Optional Equipment


1 Installation and Commissioning of a 6081-2 System _________________________________________ 60812-IC 5


10 © Festo Didactic



Required Space (H x W x D) No additional floor space required


Servo Control of Pneumatic Systems6081-40

The training system Servo Control of Pneumatic Systems introduces students to servo-controlled pneumatic systems and their associated circuitry.

The training system courseware is also available in eLearning format for users who prefer a computer-based approach.

List of Equipment


1 Signal Conditioners _____________________________________________________________________ 6366-001 PID Controller _________________________________________________________________________ 6367-001 Position Transducer ____________________________________________________________________ 6395-001 Servo Control Valve _____________________________________________________________________ 6429-001 Proportional Control Valve (3/2-Way Single-Pilot Valve) _______________________________________ 6430-001 Pressure Transducer ____________________________________________________________________ 6471-001 Muffler _______________________________________________________________________________ 6493-00

Manual


Servo Control of Pneumatic Systems (Student Manual) ___________________________________________ 31977-00


Servo Control of Pneumatic Systems (Student Manual) (31977-00)• 1 Introduction to Servo Control Valves• 2 Acceleration and Deceleration Control• 3 Open-Loop Position Control• 4 Closed-Loop Position Control, Proportional Mode• 5 Closed-Loop Position Control, Proportional-Plus-Integral Mode• 6 Open-Loop Speed Control• 7 Closed-Loop Speed Control, Proportional-Plus-Integral-Plus-Derivative Mode• 8 Closed-Loop Pressure Control, Proportional-Plus-Integral Mode



© Festo Didactic 11




1 Training on Servo Control of Pneumatic Systems, 0.5 day _____________________________________ 31977-TF

Optional Equipment







Pneumatics Fundamentals (Add-On)6081-90The Pneumatics Fundamentals (Add-On) training system introduces students to the basic principles and components of pneumatics. This training system is similar to Model 6081-1, but does not include the Work Surface, Model 6301.

All components in this training system can be simulated using the Windows®-based Pneumatics Simulation



List of Equipment


1 Storage/Work Surface __________________________________________________________________ 6309-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-10

6

7






1 Long Line _____________________________________________________________________________ 6492-00

List of Manuals







1 Training on Pneumatics Fundamentals, 1.1 days ____________________________________________ 31290-TF

Optional Equipment






Net Weight TBE

8

9



Pneumatics Fundamentals (with Standard Bench, Unassembled)6081-A0

The Pneumatics Fundamentals (with Standard Bench, Unassembled) training system introduces students to the basic principles and components of pneumatics.

This training system includes the same components as Model 6081-1, with the addition of an unassembled bench and two storage/work surfaces.


can be simulated using the Windows®-

based Pneumatics Simulation Software (LVSIM®-PNEU), Model 6485. The simulated components can be interconnected and their operation studied using the same courseware as that used for the real equipment.


List of Equipment


1 Work Surface __________________________________________________________________________ 6301-001 Bench (Unassembled) __________________________________________________________________ 6303-102 Storage/Work Surface __________________________________________________________________ 6309-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-101 Long Line _____________________________________________________________________________ 6492-00

List of Manuals











1 Training on Pneumatics Fundamentals, 1.1 days ___________________________________________ 31290-TF

Optional Equipment


1 Installation and Commissioning of a 6081-1 System ________________________________________ 60811-IC






Required Space (H x W x D) 1500 x 1800 x 1500 mm (60 x 70.9 x 59.1 in)

Net Weight TBE

10

11



Pneumatics Fundamentals (with Lockable Bench, Unassembled)6081-B0

The Pneumatics Fundamentals (with Lockable Bench, Unassembled) training system introduces students to the basic principles and components of pneumatics.

This training system includes the same components as Model 6081-1, with the addition of an unassembled bench with dressing panels and lockable doors, and two storage/work surfaces.




List of Equipment


1 Work Surface __________________________________________________________________________ 6301-001 Bench (Unassembled) __________________________________________________________________ 6303-101 Dressing Panels (with Lockable Front Door) _________________________________________________ 6303-A02 Storage/Work Surface __________________________________________________________________ 6309-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-101 Long Line _____________________________________________________________________________ 6492-00





List of Manuals








Optional Equipment









Net Weight TBE

12

13



Pneumatics Fundamentals (with Lockable Bench, Assembled)6081-C0

The Pneumatics Fundamentals (with Lockable Bench, Assembled) training system introduces students to the basic principles and components of pneumatics.

This training system includes the same components as Model 6081-1, with the addition of an assembled bench with dressing panels and lockable doors, and two storage/work surfaces.




List of Equipment


1 Work Surface __________________________________________________________________________ 6301-001 Bench (with Dressing Panels and Lockable Front Door, Assembled) ______________________________ 6303-C02 Storage/Work Surface __________________________________________________________________ 6309-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-101 Long Line _____________________________________________________________________________ 6492-00

List of Manuals












Optional Equipment









Net Weight TBE

Pneumatics Fundamentals (with Lockable Bench, A-Frame, Unassembled)6081-D0The Pneumatics Fundamentals (with Lockable Bench, A-Frame, Unassembled) training system introduces students to the basic principles and components of pneumatics.

This training system includes the same components as Model 6081-1, with the addition of an unassembled bench with dressing panels and lockable doors, as well as two storage/work surfaces. Also, the training system includes a Work Surface (Dual A-Frame), Model 6301-1 , that replaces Model 6301-0.

14

15






List of Equipment


1 Work Surface (A-Frame) _________________________________________________________________ 6301-101 Bench (with Dressing Panels and Lockable Doors, Unassembled) _______________________________ 6303-E02 Storage/Work Surface __________________________________________________________________ 6309-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-101 Long Line _____________________________________________________________________________ 6492-00

List of Manuals




Pneumatics Fundamentals (Student Manual) (31290-00)• 1-1 Familiarization with the Lab-Volt Pneumatics Trainer• 1-2 Introduction to Pneumatics• 1-3 Air Conditioning and Distributing Equipment• 2-1 Pressure vs Force Relationship• 2-2 Pressure vs Volume Relationship• 2-3 Pressure Drop vs Flow Relationship• 2-4 Vacuum Generation• 3-1 Directional Control Valves• 3-2 Directional and Speed Control of Cylinders





• 3-3 Cylinders in Series• 3-4 Cylinders in Parallel• 4-1 Indirect Control Using Pilot-Operated Valves• 4-2 Pneumatic Motor Circuits• 4-3 Pneumatic Motor Performance




Optional Equipment









Net Weight TBE

Pneumatics Fundamentals (with Lockable Bench, A-Frame, Assembled)6081-E0

The Pneumatics Fundamentals (with Lockable Bench, A-Frame, Assembled) training system introduces students to the basic principles and components of pneumatics.

This training system includes the same components as Model 6081-1, with the addition of an assembled bench with dressing panels and lockable doors, as well as two storage/work surfaces. Also, the training system includes a Work Surface (Dual A-Frame), Model 6301-1 , that replaces Model 6301-0.



16

17




List of Equipment


1 Work Surface (A-Frame) _________________________________________________________________ 6301-101 Bench (with Dressing Panels and Lockable Doors, Assembled) _________________________________ 6303-D02 Storage/Work Surface __________________________________________________________________ 6309-001 Conditioning Unit ______________________________________________________________________ 6411-001 Accumulator __________________________________________________________________________ 6412-001 Vacuum Generator _____________________________________________________________________ 6413-002 Directional Control Valve (3/2-Way Push-Button Valve) _______________________________________ 6420-002 Flow Control Valve ______________________________________________________________________ 6421-001 Directional Control Valve (5/2-Way Double-Pilot Valve) _______________________________________ 6422-001 Single-Acting Cylinder ___________________________________________________________________ 6440-001 Double-Acting Cylinder __________________________________________________________________ 6441-001 Bidirectional Motor _____________________________________________________________________ 6442-001 Air Bearing ____________________________________________________________________________ 6443-001 Pressure Gauge ________________________________________________________________________ 6450-001 Flowmeter ____________________________________________________________________________ 6451-001 Loading Device ________________________________________________________________________ 6480-001 Tees _________________________________________________________________________________ 6490-001 Tubing and Accessories _________________________________________________________________ 6491-101 Long Line _____________________________________________________________________________ 6492-00

List of Manuals




Pneumatics Fundamentals (Student Manual) (31290-00)• 1-1 Familiarization with the Lab-Volt Pneumatics Trainer• 1-2 Introduction to Pneumatics• 1-3 Air Conditioning and Distributing Equipment• 2-1 Pressure vs Force Relationship• 2-2 Pressure vs Volume Relationship• 2-3 Pressure Drop vs Flow Relationship• 2-4 Vacuum Generation• 3-1 Directional Control Valves• 3-2 Directional and Speed Control of Cylinders• 3-3 Cylinders in Series• 3-4 Cylinders in Parallel• 4-1 Indirect Control Using Pilot-Operated Valves• 4-2 Pneumatic Motor Circuits





• 4-3 Pneumatic Motor Performance




Optional Equipment









Net Weight TBE

Troubleshooting Pneumatic Circuits6081-F0

The Troubleshooting Pneumatic Circuits training system develops the skills of students in troubleshooting using specially modified components that cause erratic operation.

List of Equipment


1 Conditioning Unit (Faulty) ________________________________________________________________ 6411-F01 Accumulator (Faulty) ____________________________________________________________________ 6412-F01 Vacuum Generator (Faulty) _______________________________________________________________ 6413-F01 Directional Control Valve (3/2-Way Push-Button Valve, Faulty) _________________________________ 6420-F01 Directional Control Valve (5/2-Way Double-Pilot Valve, Faulty) _________________________________ 6422-F01 Loading Device (Faulty) _________________________________________________________________ 6480-F01 Tees (Faulty) __________________________________________________________________________ 6490-F0

18

19



20 Installation and basic commissioning of the equipment in your classroom. Installer fees (flight, accommodation...) must be added to the price. The product (box(es) and/or pallet(s)) must already be in the classroom or extra charges will apply. For details or other options, contact



1 Long Line (Faulty) ______________________________________________________________________ 6492-F0

Manual


Troubleshooting Pneumatic Circuits (Instructor Guide) ___________________________________________ 86272-10

Optional Equipment



Hydraulics and Pneumatics Applications – PLC (Allen Bradley)6082-50

Hydraulics and Pneumatics Applications - PLC (Allen Bradley) is a subsystem of the Hydraulics and Pneumatics Training Systems, Models 6080 and 6081. The subsystem introduces students to hydraulics and pneumatics applications controlled by PLCs.

The system includes an Allen-Bradley PLC and Rockwell software. It also includes two student manuals: one applicable to hydraulics and one applicable to pneumatics.

List of Equipment


1 PLC Software (RSLogix Micro, Educational) __________________________________________________ 3245-A01 Communication Cable (Allen-Bradley) ______________________________________________________ 3246-401 Programmable Logic Controller (Allen-Bradley) ______________________________________________ 3270-70

List of Manuals


Hydraulics Applications - PLC (Student Manual) _________________________________________________ 31305-00Pneumatics Applications – PLC (Student Manual) _______________________________________________ 31726-00


Hydraulics Applications - PLC (Student Manual) (31305-00)• 1 Programmable Logic Controller Review• 2 Timer Instructions

20



21 Refer to the Computer Requirements in the System Specifications section of this datasheet if the computer is to be provided by the end-user.22 Optional product training. Price provided on demand. For details and options, contact [email protected].

• 3 Counter Instructions• 4 Latching and Comparison Instructions• 5 Time-Delay Control of Hydraulic Actuators• 6 Counting of Hydraulic Actuator Cycles• 7 Safety Control of Hydraulic Actuators• 8 PLC-Controlled Clamp and Work System• 9 Troubleshooting• 10 Designing a PLC-Controlled Punching Press• 11 Designing a PLC-Controlled Conveyor System• 12 Designing a PLC-Controlled Die Casting Machine

Pneumatics Applications – PLC (Student Manual) (31726-00)• 1 Programmable Logic Controller Review• 2 Timer Instructions• 3 Counter Instructions• 4 Latching and Comparison Instructions• 5 Time-Delay Control of Pneumatic Actuators• 6 Counting of Pneumatic Actuator Cycles• 7 Safety Control of Pneumatic Actuators• 8 PLC-Controlled Clamp and Work System• 9 Troubleshooting• 10 Designing a PLC-Controlled Stamping Machine• 11 Designing a PLC-Controlled Conveyor System• 12 Designing a PLC-Controlled Injection Molding Machine



1 Personal Computer ____________________________________________________________________ 8990-001 Training on PLC Applications, 0.8 day ____________________________________________________ 31305-TF


Computer RequirementsA currently available personal computer with USB 2.0 ports, running under one of the following operating

systems: Windows® 7 or Windows® 8.


Intended Location Installed on the work surface of a Hydraulics Training System.

Dimensions (H x W D) TBE

Net Weight TBE

21

22



Sensors Training System6085-00

The Sensors Training System familiarizes students with the operation of various types of sensors. The training system is an add-on to the Electrical Control of Hydraulic Systems, Model 6080-2, and Electrical Control of Pneumatic Systems, Model 6081-2. It does not include a work surface and the sensors must be installed on a work surface of the Hydraulics and Pneumatics Training Systems in order to perform the

exercises in the included courseware.

The system contains a selection of photoelectric, inductive, and capacitive sensors representative of what is found in the industry. The training system provides a comprehensive, high-quality, and cost-effective solution to rapidly build student knowledge in sensors.

Each sensor is mounted on a flexible support attached to a metal base whose fixations can be inserted into the perforations of the trainer work surfaces.

The sensor inputs and outputs are accessible through banana jacks, allowing for easy system setup. The sensors are protected against bad connections and reverse polarity, and are identified with the proper symbol on their base. All components meet industrial safety standards.

A block, on which reflectors have been added, is used to observe the characteristics of each sensor.

The Sensors courseware consists of a student manual and an instructor guide. The student manual is divided into seven hands-on exercises. Each exercise provides a clearly stated objective, a discussion, a summary of the exercise procedure, a detailed exercise procedure, and a conclusion. The instructor guide contains the measurement results as well as the answers for each hands-on exercise of the student manual.

List of Equipment


1 Background Suppression Photoelectric Switch ______________________________________________ 6373-001 Polarized Retroreflective Photoelectric Switch _______________________________________________ 6374-001 Inductive Proximity Switch _______________________________________________________________ 6375-001 Capacitive Proximity Switch ______________________________________________________________ 6376-001 Diffuse Reflective Photoelectric Switch _____________________________________________________ 6377-001 Fiber-Optic Photoelectric Switch __________________________________________________________ 6378-001 Reflective Block ________________________________________________________________________ 6396-00

List of Manuals


Sensors (Student Manual) __________________________________________________________________ 32606-00Sensors (Instructor Guide) __________________________________________________________________ 32606-10




Sensors (Student Manual) (32606-00)• 1 Introduction to Sensors• 2 Diffuse Reflective Photoelectric Switches• 3 Background Suppression Photoelectric Switches• 4 Fiber-Optic Photoelectric Switches• 5 Polarized Retroflective Photoelectric Switches• 6 Capacitive Proximity Switches• 7 Inductive Proximity Switches



Intended Location On the work surface of another training system such as the Hydraulics or Pneumatics Training Systems

Dimensions (H x W x D) 555 x 290 x 202 mm (21.9 x 11.4 x 8 in)


Equipment Description

PLC Software (RSLogix Micro, Educational) 3245-A0

The RSLogix Micro software is a tool to design and implement ladder programs for the Allen-Bradley MicroLogix™ family of processors (it cannot be used with SLC 500

controllers). It is a Windows®-based application produced by Rockwell Software that allows PLC programming using a personal computer.

The free-form ladder of RSLogix Micro lets students concentrate on the

application logic rather than using the proper syntax when editing programs. Several other features of RSLogix Micro greatly facilitate PLC programming, such as a project verifier, drag-and-drop editing, and search-and-replace functions. The PLC can be programmed via either an RS-232 port or an Ethernet port on the PLC processor. This software comes with RSLinx™, which provides connectivity between the PLC and the computer.

The software is available with either an educational license (Model 3245-A) or as a commercial license (Model 3245-B).

SpecificationsParameter Value

Computer RequirementsA currently available personal computer with USB 2.0 ports, running under one of the following operating

systems: Windows® 7 or Windows® 8.



Communication Cable (Allen-Bradley) 3246-40

The communication cable is an RS-232-C serial cable specifically designed to connect a personal computer to an Allen-Bradley programmable logic controller, thus making it possible to program and monitor the PLC.


Communication Cable

Type 8 pin mini DIN to 9 pin D shell

Length 2 m (6.5 ft)

Programmable Logic Controller (Allen-Bradley) 3270-70

The Programmable Logic Controller (Allen-Bradley) is mounted on a metal base which allows it to be clamped onto a perforated work surface. The PLC has the capacity to accept eight 24 V dc input signals from input elements, such as push buttons, limit switches, magnetic switches, and photoelectric switches. It can control up to six 24 V dc output devices, such as pilot lamps and solenoids. All PLC inputs and outputs are terminated with banana jacks to ease system setup.

Features & Benefits

• Compact design• Digital I/O: eight inputs (24 V dc) and six outputs (24 V dc)• Fully configurable, integrated PID controller• Form factor compatible with the perforated work surfaces of the Hydraulics and Pneumatics training systems• Requires programming software, Model 3245-A, and communication cable, Model 3246-4• Used with the Hydraulics and Pneumatics training systems, Series 6080 and 6081, includes courseware


Manufacturer Allen-Bradley

CPU Type MicroLogix 1100



Parameter Value

Power 24 V dc

Discrete Inputs

Quantity 10

Ratings 24 V dc

Discrete Outputs

Quantity, Type, and Ratings Two relay outputs

Two 24 V dc FET outputs

Two high-speed 24 V dc FET outputs

Program Memory 4 kB

Data Memory 4 kB


Dimensions (H x W x D) 200 x 240 x 200 mm (7.9 x 9.4 x 7.9 in)

Net Weight TBE

Work Surface 6301-00

The Work Surface consists in a solid metal, universal drip-tray hinged to a perforated, tiltable work surface on which components can be mounted. The Work Surface can be placed atop a regular work table or on an optional bench, such as the Model 6303, which provides mobility and storage space.



Dimensions (H x W x D) 80 x 900 x 700 mm (3 x 35.5 x 27.5 in) when the perforated work surface is lowered


Work Surface (A-Frame) 6301-10

The Work Surface (A-Frame) consists of two sloping work surfaces joined at the top and braced at their base by a universal drip tray. It allows two groups of students to connect separate circuits. It can be placed atop a regular work table or on an optional bench, such as the Model 6303, which provides mobility and separate storage for the components.




Net Weight 23.6 kg (52 lb)



Expanding Work Surface (Large) 6302-00

The Expanding Work Surface (Large) consists in a perforated plate that can be mounted on the main Work Surface, Model 6301, to increase the work area. The Expanding Work Surface (Large) is two-thirds the main Work Surface in area.



Dimensions (H x W x D) 30 x 590 x 590 mm (1 x 23 x 23 in)


Bench (Unassembled) 6303-10

The Bench (Unassembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant requires assembly and does not comprise any dressing panel.



Intended Location On the floor (stands on casters)





Dressing Panels (with Lockable Front Door) 6303-A0

The Dressing Panels (with Lockable Front Door) are used to fully enclose the benches, Models 6303-1 and 6303-B. The lockable front doors consist of two hinged panels with a lock handle to secure the content of the bench. A pair of lockable side doors are provided to secure the components stored on the side shelves.



Intended Location Installed on the front, rear, and sides of a Bench, Model 6303-1 or 6303-B


Bench (with Dressing Panels and Lockable Front Door, Assembled) 6303-C0

The Bench (with Dressing Panels and Lockable Front Door, Assembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant is provided already assembled and comprises dressing

panels with a lockable front door. These dressing panels fully enclose the bench. The lockable front door consists of two hinged panels with a lock handle to secure the content of the bench.





Net Weight 64 kg (141 lb)



Bench (with Dressing Panels and Lockable Doors, Assembled) 6303-D0

The Bench (with Dressing Panels and Lockable Doors, Assembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant is provided already assembled and comprises dressing panels with lockable front, rear, and side doors. These dressing panels fully

enclose the bench. The lockable doors consist of two hinged panels with a lock handle to secure the content of the bench.

The supports of the work surfaces on this bench variant allow separate storage of components and can accommodate two student groups.






Bench (with Dressing Panels and Lockable Doors, Unassembled) 6303-E0

The Bench (with Dressing Panels and Lockable Doors, Unassembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant requires assembly and comprises dressing panels with



lockable front, rear, and side doors. These dressing panels fully enclose the bench. The lockable doors consist of two hinged panels with a lock handle to secure the content of the bench.







Storage/Work Surface 6309-00

The Storage/Work Surface is a perforated metal plate on which the equipment is placed. Two work surfaces can be joined using Spacers, Model 39035.





DC Power Supply 6360-A0

The DC Power Supply converts the ac line voltage into a 24 V dc voltage. The power supply is protected against short circuits by an automatic current/limit circuit.

Specifications



Parameter Value

Power Requirements

Voltage 100-240 V ac

Current 4.4 A

Service Installation Standard single-phase ac outlet

Output

Voltage 24 V dc

Current 5.0 A



Net Weight TBE

Push-Button Station 6361-00

The Push-Button Station consists of two momentary push-button switches, one with normally-open contact, and one with normally-closed contact.


Push-Buttons Two, momentary

Contacts NO, NC, 24 V dc – 3 A




Limit-Switch Assembly 6362-00

The Limit-Switch Assembly consists of two mechanical limit switches actuated by a roller arm. The limit switches are used for detecting the rod position of the cylinders. Each switch has one normally open and one normally closed contact.

Specifications



Parameter Value

Switches Two, roller-lever actuated, momentary

Contacts SPDT, 24 V dc – 3 A

Switch Positioning Range Switches must be positioned within 15 cm (6 in) of each other




Relay 6363-00

The Relay consists in a relay coil controlling three sets of normally open and normally closed contacts.


Type General purpose, plug-in

Coil Voltage 24 V dc

Contacts SPDT; 24 V dc – 3 A






Time-Delay Relay / Counter 6364-00

The Time-Delay Relay / Counter consists in a relay that can be programmed for either timing or counting function. The relay has two sets of normally-open and normally-closed contacts.


Type Programmable, multifunction, digital, LCD display

Timing Range 0.1 s to 9990 h

Counting Range 1-99900

Contacts DPDT; 24 V dc – 3 A




Pilot-Lamp Station 6365-00

The Pilot-Lamp Station consists of two amber incandescent pilot lamps whose terminals can be accessed using miniature banana jacks.


Lamps

Quantity 2

Color Amber

Type Incandescent

Voltage Rating 24 V dc




Parameter Value



Signal Conditioners 6366-00

The Signal Conditioners module consists of a voltage converter with adjustable outputs, a voltage converter with fixed-calibration outputs, and a frequency-to-voltage converter with adjustable and fixed-calibration outputs. The Signal Conditioners module is used to convert the signals provided by the Pressure Transducer, Model 6471, the Position Transducer, Model 6395, and the Diffuse Reflective Photoelectric Switch, Model 6372, into signals of normalized range that are suitable for

transmission to a controller.


Power Requirements 24 V dc

Rating (All Converters)

Output Voltages 0-5 V and 0-10 V

Output Impedance 1 kΩVoltage Converter (with Adjustable Outputs)

Input Voltage 0-5 V

Input Impedance 1 MΩZero Adjustment 0-2.2 V approx.

Span Adjustment 1.0-4.7 V approx.

Voltage Converter (with Fixed-Calibration Outputs)

Input Voltage 0-24 V

Input Impedance 150 kΩFrequency Converter

Input Frequency 2-33 Hz

Fixed-Calibration Output 1 V/1000 r/min

Span Adjustment 16-33 Hz






PID Controller 6367-00

The PID Controller consists of various controls and circuits that allow open- and closed-loop control. The PID Controller circuits include a setpoint generator, a ramp generator, an error detector, a low-pass filter, proportional (P), integral (I), and derivative (D) amplifiers, a summing amplifier, and a limiter circuit. Each circuit is independently terminated to permit students to wire the PID controller in different configurations.


Power Requirement

Current 0.5 A


Rating (all Sections)

Input Voltage -10 to +10 V

Output Voltage -10 to +10 V

Input Impedance 1 MΩOutput Impedance 1 kΩSetpoints Two, selectable using either a control voltage (24 V dc) or a toggle switch

Ramp Generator

Ramp Time Adjustable between 0.5 and 3 s, for both positive and negative control voltages.

Error Detector

Inputs One inverted, two non-inverted

Voltage Gain (for each input) 1

Low-Pass Filter

Cutoff Frequency 0.02-2 Hz

P.I.D. Amplifiers

Proportional Gain (Low) 0.5-5

Proportional Gain (High) 5-50 approx.

Integral Gain 0.01-1 s approx.

Derivative Gain 0.05-1 s approx.

Integrator Anti-Reset On/Off selector

Summing Point

Voltage Gain 1

Inputs Three, non-inverted

Limiter Output Voltage

Lower Limit 0 to -10 V

Upper Limit 0 to +10 V






Magnetic Proximity Switch 6371-00

The Magnetic Proximity Switch consists of two mechanical reeds and an internal coil controlling a normally open and a normally closed contact. It is used for detecting the rod position of the cylinders.


Type Reed

Supply Voltage 24 V dc

Contact SPDT; 24 V dc – 3 A




Diffuse Reflective Photoelectric Switch 6372-00

The Diffuse Reflective Photoelectric Switch consists of a light source and a receiver combined in the same casing. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.


Type Diffuse reflective

Light Source Visible red, 680 nm, eye safe

Maximum Sensing Range 10.2 cm (4 in)





Parameter Value




Background Suppression Photoelectric Switch 6373-00

The Background Suppression Photoelectric Switch consists of a light source and a receiver combined in the same casing. The sensor is mounted on a flexible support for easy positioning. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.


Light Source Infrared LED, 880 nm

Maximum Range 10 cm (4 in)


Contacts

Type SPDT

Ratings 24 V dc - 3 A



Net Weight 500 g (1.1 lb)

Polarized Retroreflective Photoelectric Switch 6374-00

The Polarized Retroreflective Photoelectric Switch consists of a light source and a receiver combined in the same casing. The sensor requires a special retroreflective surface. The sensor is mounted on a flexible support for easy positioning. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.




Light Source Visible red LED, 660 nm

Maximum Range 3 m (10 ft)


Contacts

Type SPDT





Inductive Proximity Switch 6375-00

The Inductive Proximity Switch is sensitive to metals. The sensor is mounted on a flexible support for easy positioning. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.


Maximum Range 10 mm (0.4 in)


Contacts

Type SPDT







Capacitive Proximity Switch 6376-00

The Capacitive Proximity Switch is sensitive to every material. The sensor is mounted on a flexible support for easy positioning. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.


Maximum Range 25 mm (1 in)


Contacts

Type SPDT





Diffuse Reflective Photoelectric Switch 6377-00

The Diffuse Reflective Photoelectric Switch consists of a light source and a receiver combined in the same casing. The sensor is mounted on a flexible support for easy positioning. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.






Parameter Value


Contacts

Type SPDT





Fiber-Optic Photoelectric Switch 6378-00

The Fiber-Optic Photoelectric Switch consists of a fiber-optic photoeletric switch whose light source is a visible red LED. The sensor is mounted on a flexible support for easy positioning. The model has one normally open and one normally closed contact, and the electrical connections are made using miniature banana jacks.





Contacts

Type SPDT







Multimeter 6394-A0

The Multimeter is used for ac/dc voltage, dc current, and resistance measurements.


Type Digital, handheld (portable)

Functions AC/DC voltage, dc current, resistance, continuity diode test, and battery test

Accuracy ±2.0% or better

Display 3½ digit, liquid-crystal

FeaturesSafety-recessed test lead connections, low-battery indication, audible continuity, overload protection, mounted on a base that clamps to the work surface using quick-lock fixations




Position Transducer 6395-00

The Position Transducer provides a voltage corresponding to the rod position of a cylinder. It consists of a flexible cable wound on a cylindrical spool. The cable is ended by a pin that attaches to the rod of the cylinders.


Type Cable extension spool

Position Sensing Range 0-100 mm (0-4 in)



Parameter Value

Output Voltage 0-24 V dc





Reflective Block 6396-00

The Reflective Block consists of a block with various types of reflection surfaces: white, black, shiny metallic, matte black metallic, and retroreflective. The dimensions of the block are: 75 x 75 x 75 mm (3 x 3 x 3 in).


Surfaces White, black, shiny metallic, matte black metallic, retroreflective






Conditioning Unit 6411-00

The Conditioning Unit conditions and regulates the pressure of the air supplied to the pneumatic circuits. It consists of a main shutoff valve, filter, a pressure regulator, pressure gauge, 4-port manifold, four sleeve valves, and a muffler. The Conditioning Unit requires compressed air from a central air supply or a portable unit.





Filter Regulator

Maximum Air Flow Rate 550 L/min (19 SCFM)

Operating Pressure 50-700 kPa (7-100 psi)

Filtration 5 µm

Pressure Gauge

Diameter 50 mm (2 in)


Outlet Ports Four




Conditioning Unit (Faulty) 6411-F0

The Conditioning Unit (Faulty) is a modified version of the Conditioning Unit, Model 6411-0, used to perform troubleshooting exercises.




Recommended Compressed Air Supply



Filter Regulator



Filtration 5 μm

Pressure Gauge

Diameter 50 mm (2 in)


Outlet Ports 4




Accumulator 6412-00

The Accumulator consists in a metal tank that is used to store compressed air.


Volume 1000 cm³ (61 in³)

Maximum Operating Pressure 700 kPa (100 psi)


Dimensions (H x W x D) 102 x 305 x 127 mm (4.0 x 12 x 5.0 in)




Accumulator (Faulty) 6412-F0

The Accumulator (Faulty) is a modified version of the Accumulator, Model 6412-0, used to perform troubleshooting exercises.


Volume 1000 cm³ (61 in³)



Dimensions (H x W x D) 102 x 305 x 127 mm (4.0 x 12 x 5.0 in)


Vacuum Generator 6413-00

The Vacuum Generator consists in a venturi duct that temporarily restricts the area through which the air must flow, thereby decreasing the air pressure below atmospheric pressure.


Vacuum Pressure 2130 mm (84 in) of water at 140-kPa (20-psi) inlet pressure






Vacuum Generator (Faulty) 6413-F0

The Vacuum Generator (Faulty) is a modified version of the Vacuum Generator, Model 6413-0, used to perform troubleshooting exercises.


Vacuum Pressure 2130 mm (84 in) of water at 140 kPa (20 psi) inlet pressure




Directional Control Valve (3/2-Way Push-Button Valve) 6420-00

The Directional Control Valve (3/2-Way Push-Button Valve) consists in a three ports, two spool positions, actuation by pressing, spring return directional control valve.


Type 3-way, 2-position, push-button operated, spring return







Directional Control Valve (3/2-Way Push-Button Valve, Faulty) 6420-F0

The Directional Control Valve (3/2-Way Push-Button Valve, Faulty) is a modified version of the Directional Control Valve (3/2-Way Push-Button Valve), Model 6420-0, used to perform troubleshooting exercises.


Type 3-way, 2-position, push-button operated, spring return





Flow Control Valve 6421-00

The Flow Control Valve consists of a needle valve and a reverse free-flow check valve connected in parallel. It restricts the flow rate in one direction, while allowing the air to flow freely in the other direction.


Minimum Operating Pressure 105 kPa (15 psi)







Directional Control Valve (5/2-Way Double-Pilot Valve) 6422-00

The Directional Control Valve (5/2-Way Double-Pilot Valve) consists in a five ports, two spool positions, pneumatically actuated in both directions, directional control valve.


Type 5 ports, 4 ways, 2 positions, double air-pilot operated





Directional Control Valve (5/2-Way Double-Pilot Valve, Faulty) 6422-F0

The Directional Control Valve (5/2-Way Double-Pilot Valve, Faulty) is a modified version of the Directional Control Valve (5/2-Way Double-Pilot Valve), Model 6422-0, used to perform troubleshooting exercises.




Type 5 ports, 4 ways, 2 positions, double air-pilot operated





Directional Control Valve (5/3-Way Double-Solenoid Valve) 6423-00

The Directional Control Valve (5/3-Way Double-Solenoid Valve) consists in a five ports, three spool positions, actuated by solenoid and pneumatic piloting in both directions, spring centered, closed center, directional control valve.


Type 5 ports, 4 ways, 3 positions, double-solenoid operated, spring centered, closed center

Solenoids 24 V dc






Single Solenoid-Actuated Directional Control Valve 6424-00

The Single Solenoid-Actuated Directional Control Valve consists of a five ports, two spool positions, actuated by solenoid and pneumatic piloting in one direction, spring return, directional control valve.


Type 5 ports, 4 ways, 2 positions, single-solenoid operated, spring return

Solenoids 24 V dc




AND Function Valve (Dual-Pressure Valve) 6425-00

The AND Function Valve (Dual-Pressure Valve) consists in a three ports, two spool position, pneumatically operated valve. The valve allows fluid to flow through it when both input ports are pressurized, according to the AND function in Boolean logic.


Actuator Type Single acting, spring return, air pilot

Actuating Pressure 210 kPa (30 psi)



Parameter Value





Shuttle Valve (OR Function Valve) 6426-00

The Shuttle Valve (OR Function Valve) consists of a double check valve with two inlet ports and one outlet port. The valve allows fluid to flow through it from the inlet port having the highest pressure, according to the OR function in Boolean logic.






Quick Exhaust Valve 6427-00

The Quick Exhaust Valve consists of a three-way valve with a diaphragm that allows fluid at the output port side to be exhausted to atmosphere when the pressure at the output port becomes higher than that at the valve inlet port.








Pressure Regulator 6428-00

The Pressure Regulator consists in a normally open valve that closes when the pressure at its outlet port exceeds the pressure set by the valve knob.



Pressure Range 50-700 kPa (7-100 psi)




Servo Control Valve 6429-00

The Servo Control Valve provides control of the pressure in proportion to a control voltage. It consists of an inlet valve and an exhaust valve, a built-in electronic circuit, and a pressure transducer. The pressure transducer provides the electronic circuit with a feedback signal that corresponds to the actual valve output pressure, the feedback signal is accessible for monitoring.

Specifications



Parameter Value

Type Pressure Control

Power Requirement 24 V dc – 0.25 A

Control Voltage 0-10 or 0-5 V dc

Output Pressure 0-700 kPa (0-100 psi)

Rated Flow 34 L/min (1.2 SCFM) at 700 kPa (100 psi)

Pressure Transducer Monitoring Output 0-10 V

Linearity/Hysteresis ± 0.15%

Repeatability ± 0.02%

Accuracy ± 0.2%




Proportional Control Valve (3/2-Way Single-Pilot Valve) 6430-00

The Proportional Control Valve (3/2-Way Single-Pilot Valve) consists in a three port, spring return valve whose operation is pneumatically controlled in one direction. This provides control of the flow rate in proportion to a pilot pressure. This valve is intended to be used in conjunction with the Servo Control Valve, Model 6429.


Type 3 ways, 2 positions, single air-pilot operated, spring return

Rated Flow 140 L/min (5 SCFM) at 700 kPa (100 psi)






Single-Acting Cylinder 6440-00

The Single-Acting Cylinder provides a linear pushing motion over a 10.2 cm (4 in) stroke. Its rod is extended under compressed air and retracted by a spring. The cylinder piston is equipped with a permanent ring magnet intended to actuate the Magnetic Proximity Switch, Model 6371.


Piston Spring return, with permanent ring magnet

Stroke 100 mm (4 in)

Bore Size 27 mm (1.1 in)





Double-Acting Cylinder 6441-00

The Double-Acting Cylinder provides a linear push-pull motion over a 10.2 cm (4 in) stroke. Its rod is both extended and retracted under compressed air. The cylinder piston is equipped with a permanent ring magnet intended to actuate the Magnetic Proximity Switch, Model 6371.


Piston With permanent ring magnet

Stroke 100 mm (4 in)

Bore Size 27 mm (1.1 in)



Parameter Value





Bidirectional Motor 6442-00

The Bidirectional Motor is a vane-type pneumatic motor that provides rotary motion in either direction. A white sticker affixed onto the motor shaft allows counting of the motor revolutions using a photoelectric switch.


Type Vanes

Ratings

Maximum Power 250 W (0.33 hp)


Maximum Speed 10 000 r/min




Air Bearing 6443-00

The Air Bearing consists of a disk with a side inlet duct leading to an underneath cavity. When pressurized air enters the side inlet duct, a thin film of escaping air is formed between the Air Bearing and the work surface, resulting in a friction-free movement in any direction.


Diameter 63 mm (2.5 in)






Pressure Gauge 6450-00

The Pressure Gauge (0-700 kPa) provides a direct visual reading of the pressure on a dual scale graduated in units of kilopascals (kPa) and pounds per square inch (psi). It consists of a Bourdon tube attached through a gear linkage to a needle pointer.


Diameter 38 mm (1.5 in)





Flowmeter 6451-00

The Flowmeter provides a direct visual reading of the air flow rate. It consists of a lightweight ball that moves vertically along a tapered tube with the flow of air, thereby indicating the flow rate.


Flow Range 0-150 L/min (0-5.25 SCFM)


Accuracy ± 4% of full scale





Parameter Value


Pressure Switch 6470-00

The Pressure Switch consists in a diaphragm electrical switch with adjustable actuation pressure and pressure differential. The model has one normally-open and one normally-closed contact, and the electrical connections are made using miniature banana jacks.


Adjustable Pressure Range 105-1725 kPa (15-250 psi)

Differential Range 70-210 kPa (10-30 psi)





Pressure Transducer 6471-00

The Pressure Transducer provides a voltage proportional to the pressure applied to the input port.


Type Solid state

Pressure Range 0-1000 kPa (0-145 psi)



Parameter Value

Output Voltage 0-5 V





Loading Device 6480-00

The Loading Device consists in a spring enclosed in a clear plastic tube to which a graduated (N and lbf) ruler can be clipped. The Loading Device is intended to be used with Cylinders, Models 6440 and 6441, to measure the cylinder output force at different pressures.


Spring Compression Rate 98 N/cm (56 lbf/in)

Force Measurement Ruler Designed to mount on the load device, graduated in N and lbf

Maximum Compression Force 500 N (100 lbf)




Loading Device (Faulty) 6480-F0

The Loading Device (Faulty) is a modified version of the Loading Device, Model 6480-0, used to perform troubleshooting exercises.


Spring Compression Rate 98 N/cm (56 lbf/in)

Force Measurement Ruler Designed to mount on the load device, graduated in N and lbf

Maximum Compression Force 500 N (100 lbf)






Tees 6490-00

The Tees assembly consists of six push-in tube fittings, interconnected into two groups of three, to which tubes can be connected.


Number of Tee Assemblies Two





Tees (Faulty) 6490-F0

The Tees (Faulty) is a modified version of the Tees, Model 6490-0, used to perform troubleshooting exercises.


Number of Tee Assemblies Two







Tubing and Accessories 6491-10

The Tubing and Accessories set consists of polyethylene tubing, digital tachometer, stopwatch, tube cutter, tube releasing tool, and a pair of gloves.

The tubing is cut into lengths required by pneumatic circuits using a tube cutter, then connected to the components by manually pushing the tubes into the component fittings. A tool is supplied to release the tubes

from the component fittings.

The digital tachometer indicates motor rotation speed either in a clockwise or counterclockwise direction. The measured speed is automatically indicated on a high-visibility, five-digit display, and is updated every second to enable measurements of acceleration and deceleration.


Tubing

Type Polyethylene, 6 mm (0.25 in) outside diameter, 15 m (50 ft) long


Tube Cutter For tubing with outside diameter between 6 and 12 mm (0.25 and 0.5 in)



Connection Leads (4 Lengths) 6491-A0

The Connection Leads (4 Lengths) consists in extra-flexible electrical leads terminated with stacking 2 mm banana plugs. The leads are supplied in four different lengths, and are color coded according to length.


Electrical Leads

Quantity, Length Eight, 15 cm (6 in)

Eight, 30 cm (12 in)

Ten, 45 cm (18 in)

Ten, 60 cm (24 in)

Connectors 2 mm banana plugs

Current Rating 10 A





Long Line 6492-00

The Long Line consists in an 11.5 m (38 ft) length of polyethylene coiled tubing having a small diameter. The Long Line is used to simulate the friction caused by a long tubing line.


Tubing

Type Polyethylene, 3 mm (0.13 in) outside diameter, 11.5 m (38 ft) long







Long Line (Faulty) 6492-F0

The Long Line (Faulty) is a modified version of the Long Line, Model 6492-0, used to perform troubleshooting exercises.


Tubing

Type Polyethylene, 3 mm (0.13 in) outside diameter, 11.5 m (38 ft) long





Muffler 6493-00

The Muffler is mounted on a base plate. It is used to reduce exhaust noise.



Optional Equipment Description

Extended Warranty for the Pneumatics Training System (Optional) 6081-EWThe Festo Didactic Extended Warranty program offers you the flexibility to add to the standard two-year manufacturer’s warranty. The Extended Warranty provides coverage for up to three additional years, for a total of five years of protection on your investment for your pneumatics training equipment.

Extended Warranty terms are the same as the terms for the current two-year manufacturer warranty.

Work Surface (A-Frame) (Optional) 6301-10

The Work Surface (A-Frame) consists of two sloping work surfaces joined at the top and braced at their base by a universal drip tray. It allows two groups of students to connect separate circuits. It can be placed atop a regular work table or on an optional bench, such as the Model 6303, which provides mobility and separate storage for the components.





Expanding Work Surface (Large) (Optional) 6302-00

The Expanding Work Surface (Large) consists in a perforated plate that can be mounted on the main Work Surface, Model 6301, to increase the work area. The Expanding Work Surface (Large) is two-thirds the main Work Surface in area.







Expanding Work Surface (Small) (Optional) 6302-10

The Expanding Work Surface (Small) consists in a perforated plate that can be mounted on the main Work Surface, Model 6301, to increase the work area. The Expanding Work Surface (Small) is one-third the main Work Surface in area.



Dimensions (H x W x D) 30 x 290 x 590 mm (1 x 11.5 x 23 in)


Bench (Unassembled) (Optional) 6303-10

The Bench (Unassembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant requires assembly and does not comprise any dressing panel.







Parameter Value


Dressing Panels (with Lockable Front Door) (Optional) 6303-A0

The Dressing Panels (with Lockable Front Door) are used to fully enclose the benches, Models 6303-1 and 6303-B. The lockable front doors consist of two hinged panels with a lock handle to secure the content of the bench. A pair of lockable side doors are provided to secure the components stored on the side shelves.



Intended Location Installed on the front, rear, and sides of a Bench, Model 6303-1 or 6303-B


Bench (Assembled) (Optional) 6303-B0

The Bench (Assembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant is provided already assembled, but does not comprise any dressing panels.








Bench (with Dressing Panels and Lockable Front Door, Assembled) (Optional) 6303-C0

The Bench (with Dressing Panels and Lockable Front Door, Assembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant is provided already assembled and comprises dressing

panels with a lockable front door. These dressing panels fully enclose the bench. The lockable front door consists of two hinged panels with a lock handle to secure the content of the bench.






Bench (with Dressing Panels and Lockable Doors, Assembled) (Optional) 6303-D0

The Bench (with Dressing Panels and Lockable Doors, Assembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant is provided already assembled and comprises dressing panels with lockable front, rear, and side doors. These dressing panels fully

enclose the bench. The lockable doors consist of two hinged panels with a lock handle to secure the content of the bench.









Bench (with Dressing Panels and Lockable Doors, Unassembled) (Optional) 6303-E0

The Bench (with Dressing Panels and Lockable Doors, Unassembled) consists of a mobile workstation on which the Work Surfaces, Models 6301 and 6301-1, can be mounted. Four heavy-duty, swivelling, lockable casters allow the bench to be easily moved in the laboratory classroom. The bench has three pairs of side supports over which three Storage/Work Surfaces, Model 6309, can be slid to provide shelving for component storage.

This bench variant requires assembly and comprises dressing panels with

lockable front, rear, and side doors. These dressing panels fully enclose the bench. The lockable doors consist of two hinged panels with a lock handle to secure the content of the bench.







Storage/Work Surface (Optional) 6309-00

The Storage/Work Surface is a perforated metal plate on which the equipment is placed. Two work surfaces can be joined using Spacers, Model 39035.







Air Compressor (Optional) 6410-B0

The Air Compressor is a quiet device well suited for classroom and school laboratories. It is provided with a tank, pressure regulator, pressure gauge, and a hose.

The Air Compressor is available in different variants depending on ac power network voltages and frequencies. Because of this, the actual module may vary from the one shown in the picture.


Power Requirements

Current 14.4 A

Power 1.125 kW (1.5 hp)


Tank Capacity 50 L (13 gal)

Flow Rate

Flow Rate (Free Flow) 180 L/min (6.3 CFM)

Flow Rate at 621 kpa (90 psi) 127 L/min (4.5 CFM)

Maximum Pressure 8 bar (116 psi)

Noise Level 42 dB/A (about as quiet as a refrigerator)






Directional Control Valve (Roller-Lever Operated) (Optional) 6431-00

This valve consists of two three-way, two-position, roller lever actuated, directional control valves. The valves are actuated by the rod tip of the Cylinders, Models 6440 and 6441. The valves are normally non-passing at rest position.


Type 3 ways, 2 positions, roller-lever operated





Advanced Pneumatics - eSeries (Optional) 6486-10

This site-license course bundle is intended to be used in conjunction with either the Pneumatics Training System, Series 6081, or the Pneumatics Simulation Software

(LVSIM®-PNE). Advanced Pneumatics contains the following courses: Electrical Control of Pneumatic Systems, Pneumatic Applications PLC, Servo Control of Pneumatic Systems, and Sensors, each of which has a pretest and posttest. Each course

includes the topics covered in the book-based content and their related hands-on exercises. Exercise procedures are presented in enhanced PDF format. Completed exercises may be printed, saved to a specific location, and submitted (emailed) to the instructor. Exercise presentation of technical content is accompanied by voiceover narration to minimize the amount of on-screen reading.

The following learning platforms are available:

• 6486-1: Advanced Pneumatics - eSeries



• 6486-2: Advanced Pneumatics - SCORM• 6486-3: Advanced Pneumatics - Stand-Alone


Computer RequirementsA currently available personal computer running under one of the following operating systems: Windows® 7 or

Windows® 8.

Pneumatics Fundamentals - eSeries (Optional) 6486-E0

This site-license course bundle is intended to be used in conjunction with either the Pneumatics Training System, Series 6081, or the Pneumatics Simulation Software

(LVSIM®-PNE), Model 6485. Pneumatics Fundamentals contains four courses: Introduction to Pneumatics, Basic Physical Concepts, Basic Controls of Cylinders, and Basic Controls of Pneumatic Motors, each of which has a pretest and posttest. The

courses include the topics covered in the book-based content and their related hands-on exercises. Exercise procedures are presented in enhanced PDF format. Completed exercises may be printed, saved to a specific location, and submitted (emailed) to the instructor. Exercise presentation of technical content is accompanied by voiceover narration to minimize the amount of on-screen reading.

The following learning platforms are available:

• 6486-E: Pneumatics Fundamentals - eSeries• 6486-F: Pneumatics Fundamentals - SCORM• 6486-G: Pneumatics Fundamentals - Stand-Alone

Upgrades: schools that are running the Tech-Lab version of Pneumatics Fundamentals may purchase an upgrade to the eSeries course.

• 6486-U: Pneumatics Fundamentals - eSeries (course upgrade)

Advanced variants of the above learning platforms are also available:

• 6486-1: Advanced Pneumatics - eSeries• 6486-2: Advanced Pneumatics - SCORM• 6486-3: Advanced Pneumatics - Stand-Alone


Computer RequirementsA currently available personal computer running under one of the following operating systems: Windows® 7 or

Windows® 8.



Personal Computer (Optional) 8990-00

The Personal Computer consists of a desktop computer running under

Windows® 10. A monitor, keyboard, and mouse are included.


Power Requirements

Current 2 A


Instructional DVD - Introduction to Fluid Power (Optional) 93840-10This 19-minutes video provides a balanced and concise overview of fluid power. It offers definitions, principles, and current uses relative to hydraulic and pneumatic systems.

Instructional DVD - Fluid Power Technology at Work (Optional) 93841-10This 24-minutes video provides a broad overview of hydraulics and pneumatics applications. It covers fluid power in transportation, aviation, machining, manufacturing, mining, energy, and chemical processing industries.

Instructional DVD - Pumps, Lines, Filters (Optional) 93842-10This 29-minutes video demonstrates the operation of the various types of pumps found in the industry through computer animation and live-action video. Filters, hoses, and lines are also explained.

Instructional DVD - Control Mechanisms (Optional) 93843-10This video summarizes the many ways to control fluid power systems. The construction and operation of pilot valves, solenoid valves, sensors, PLCs, and other devices are clearly explained. (27 minutes)

Instructional DVD - Actuators (Optional) 93844-10This 23-minutes video explains the construction and operation of the many types of actuators used in the industry. Cylinders, motors, rotators, grippers, pushers, lifters, rubbers, and bellows are all detailed.



Reflecting the commitment of Festo Didactic to high quality standards in product, design, development, production, installation, and service, our manufacturing and distribution facility has received the ISO 9001 certification.

Festo Didactic reserves the right to make product improvements at any time and without notice and is not responsible for typographical errors. Festo Didactic recognizes all product names used herein as trademarks or registered trademarks of their respective holders. © Festo Didactic Inc. 2018. All rights reserved.

Festo Didactic SE

Rechbergstrasse 373770 DenkendorfGermany

P. +49(0)711/3467-0F. +49(0)711/347-54-88500

Festo Didactic Inc.

607 Industrial Way WestEatontown, NJ 07724United States

P. +1-732-938-2000F. +1-732-774-8573

Festo Didactic Ltée/Ltd

675 rue du CarboneQuébec QC G2N 2K7Canada

P. +1-418-849-1000F. +1-418-849-1666

www.labvolt.com

www.festo-didactic.com

Documents

Pneumatics Training System, Model 6081 - Lab-Volt · PDF filePneumatics Applications – PLC expands upon the others with pneumatics applications controlled by PLCs. In Servo Control