Platform: XK09 Firmware: DLCH3 - Microsoft Neon & PT Cruiser will be selected for programming. Must press and hold the Programming button for 3 seconds to select a type. Flashes once

Vehicle Compatibility Chart

Wiring Diagram.

.........................................................................................................................................

Installation Procedure Overview..................................................................................................................................

...........................................................................................................................................................

Vehicle Type Programming.........................................................................................................................................

Vehicle Type Chart......................................................................................................................................................

User Configuration - Optional Programming...............................................................................................................

Tech Notes for Violet/White Wire.................................................................................................................................

LED Diagnostics.........................................................................................................................................................

02

03

04

05

05

06

07

07

Warranty...................................................................................................................................................................... 08

Index

TECHNICAL SUPPORT / INFORMATION

web resources:www.xpresskit.com

www.xpressvip.com

www.directechs.com† Chrysler and Dodge are registered trademarks and property of their respective companies.

Door lock and alarm module that interfaces directly with Chrysler and Dodge vehicles to provide features compatible with door locks, driver and passenger sliding doors (open/close), factory alarms, trunk/hatch release, and door pin status output for aftermarket alarm triggers.

Installation Guide

Downloadable Firmware for Platform XK09: DLPKGM, DLGM5X, CHRYSLER, PLXR, PKN3, DLVW1, DLHO4, DLHO5, DLHY, DLKIA1, DLKIA2, DLCH2, DLCH3, DLCH4.

Upgradable Door Lock & Alarm Interface

Platform: XK09Firmware: DLCH3

DL

doorlockINTERFACE

Update AlertFirmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

Rev.: 20100302


© 2010 Directed Electronics. All rights reserved.

Vehicle Compatibility ChartPage 2

To see a list of available features for each vehicle, visit www.xpresskit.com.

Vehicle Application Guide

2005

2004

2003

2002

2001

2000

Chrysler

PT Cruiser X X X X X

Dodge

Dakota X X X X

Durango X X X

Neon X X X X X X

RAM X X X X X

RAM SRT-10 X

SX X X

Rev.: 20100302



Please Note: Failure to proceed in the following order could result in possible vehicle damage.

If your remote start system has D2D Jumpers, make sure both Jumpers are in the horizontal operating position.

Installation Procedure Overview

4

3

2

See details on page 5.

Module programming

Power up the XK09

Once done, the interface red LED will turn ON.

If connected in W2W

Connect the 20-pin harness.

If connected in D2D

Connect the 4-pin D2D harness first, then connect the 20-pin harness.

Caution! The 20-pin connector can be easily plugged in backwards.

1

Make the necessary connections in the vehicle, as instructed in the vehicle-specific guides.

Connect the remote starter to the vehicle

Make all the connections as per the provided wiring schematics, either in W2W or D2D.

Wiring

Page 3

Rev.: 20100302



Pro

gra

mm

ing

bu

tto

n

XK09 Front Side

Wiring DiagramPage 4

XK09 Back Side

10

01

20

11

20 PIN connectorwire side view

Blue/White

Red/White

Light Green

Blue

(-) Ground When Running (Status)*

(-) Trunk*

(-) Lock*

(-) Unlock*

(+) 12 Volt*

(-) Ground*

Black

Red

+12VDC

XKLOADER2

Option A - Firmware UpgradesUse with D2D harness XKD2D65.

InternetUSB CABLE

USB PORT

Option B - Data to Data Connection to RCS Data PortUse with D2D harness HARD2D Rev. 3.

XL202**

XL202Antenna

D2D connectorwire side view

(+) 12 VoltRX

(-) GroundTX

4 PIN connectorwire side view

01

04

GrayGreen

(-) Trunk Detection Output*(-) Door Detection Output*

* These wires are not required in D2D.

** Sold separately.

GreenJ1850 BUS

1 8

169

Diagnostic connector (Face view) Under dash driver side Position 2

5 1

Front view

(+) Ignition 1PIN 3

Connect the start (+) wire output from remote starter to pin 4 of key switch connector. If no wire to pin 4,

do not connect the start (+) wire.PIN 4 (+) Start

Violet/BrownMultiplex Output

Rev.: 20100302



Vehicle Type

Neon 1

PT Cruiser 1

RAM (with OEM Alarm Only) 2

Dakota 3

Durango 3

Vehicle Type Programming

Vehicle Type Chart

Page 5

ON

START

OF

F

KEY

Remove Key5 Turn the key to the OFF position and remove it from the ignition barrel.

1 Once all the wires are properly connected, plug the wire connector into the module. The LED turns ON.

On Solid

&Press & Release

3To change the vehicle type, press and release the Programming button until the LED flashing pattern matches the desired type.

For instance: 1 flash = Type 1, 2 flashes = Type 2 and so on.Flashing Pattern

2Insert the key into the ignition barrel and turn it to the IGN position.

The LED turns OFF, then begins a flashing pattern that matches the vehicletype selection (the default type is 1).

If the module has NEVER been programmed or has been RESET, the LED will indicate which type the module is in by the number of flashes.

ON

START

OF

F

KEY

Key at IGN Off

&

Flashing Pattern

&

4

To save the vehicle type selection, press and hold the Programming button until the LED flashes once rapidly. The module will then exit the Programming mode and is ready to be used.

If the LED turns ON solid, turn the key to start the engine.

If the module has already been programmed, the number of flashes indicates once only the programmed type when applying power to the module.

&Press & Hold Flashes Once

Rev.: 20100302



User Configuration - Optional Programming

1Insert the key into the ignition at the OFF position and hold the Programming button down for at least 2 seconds. The LED flashes rapidly for 2 seconds to confirm you are in programming mode.

&Flash 2 Secs

&O

N

START

OF

F

KEY

Press & HoldKey at OFF

6 Remove the key from the ignition barrel.O

N

START

OF

F

KEY

Remove Key

5 To exit the programming mode, hold the Programming button down until the LED flashes once quickly.

Flashes Once

&Press & Hold

3To change the MODE, press once on the Programming button. The LED confirms the MODE with a number of slow flashes.

Only modes 6, 7 and 8 are available.&

Press OnceNo. of Slow

Flashes = Mode

2Release the Programming button. The LED first flashes a number of times slowly to indicate the MODE. It then flashes a number of times quickly to indicate the OPTION.

&No. of Slow

Flashes = ModeNo. of Quick

Flashes = Option

&Release

4To change the OPTION in the selected MODE, press LOCK or UNLOCK on the alarm or remote starter transmitter. The LED confirms the OPTION with a number of quick flashes.

See the list of options at the bottom of this page.

&No. of Quick

Flashes = Option

or( (Press

USER MODES are identified by a slow LED flashing pattern. For example, 1 slow flash = Mode1 and 2 slow flashes = Mode 2.

Page 6

Mode 6 - Lock when remote starter stops Mode 7 - Alarm control Mode 8 - Reset

*Option 1: Activate. *Option 1: Vehicle with alarm. *Option 1: No reset.

Option 2: Deactivate. Option 2: Vehicle without alarm. Option 2: Complete reset of the

options and module.

* Default option.

Rev.: 20100302



LED Status Description TroubleshootingDuring Power Up

Solid red Module not programmed. Data bus is not detected. Make sure the

connections to the data bus are correct by

referring to the wiring diagram, and then turn

the ignition to the ON position. In rare cases, the vehicle will need to be

started in order to detect the bus.

Flashes continuously

by increments of one

Chrysler Neon & PT Cruiser will be selected

for programming.

Must press and hold the Programming button

for 3 seconds to select a type.

Flashes once then

turns off

Chrysler Neon & PT Cruiser have been

successfully programmed.

N/A


by increments of two

Dodge RAM will be selected for programming. Must press and hold the Programming button


Flashes twice then

turns off

Dodge RAM has been successfully

programmed.

N/A


by increments of three

Dodge Dakota & Durango will be selected for

programming.

Must press and hold the Programming button


Flashes thrice then

turns off

Dodge Dakota & Durango have been

successfully programmed.

N/A

In Operating Mode

Solid red Incorrect behavior. Data is not being processed. Remove power

from the module, make sure the connections

to the data bus are correct by referring to the

wiring diagram, and then power up.

Flashes 1 second A D2D or W2W command is being

processed.

N/A

Connect to RAM (2001-03) Connect to

RAM (2004-05): :

Dark purple/Light blue wire in kick panel located under dash on driver side.Light green/Orange wire in kick panel located under dash on driver side.

Tech Notes for Violet/Brown Wire

LED Diagnostics

Make sure this wire is connected as indicated below.

With Factory Alarm

With or Without Factory Alarm

Connect to Light green/Orange wire in kick panel located under dash on driver side. PT Cruiser (2000-05) Connect to White/Green wire coming from the driver door at the side kick panel. Neon (2000-05): Connect to Light green wire kin kick panel located under dash on driver side.

* The BCM in the Dodge Dakota may go to sleep a minute after the doors have been locked and closed. If this happens a ground pulse to the driver door pin switch (Tan in DKP) before unlock will wake-up the BCM and the doors will unlock.

Dakota* (2001-04) & Durango (2003 & earlier):

:

It is important to select the correct alarm option (mode 7) that corresponds to the vehicle you are currently performance the installation on. See page 6 for more information on mode selection.

Page 7

x1*

x2*

x3*

x1sec

* In this instance of the module diagnostics, the LED flashes in a continuous sequence.

x1

x2

x3

Rev.: 20100302



This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connexion with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.920-0007 07-06

PROTECTED BY U.S. PATENTS: 5,719,551; 6,011,460 B1 *;6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7 , 0 4 6 , 1 2 6 B 1 ; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; CDN. PATENT: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2 , 4 2 0 , 9 4 7 ; 2,426,670; 2,454,089 EUROPEAN PATENT:1,053,128 PAT. PENDING: 2,291,306; MADE IN CANADA

Limited One-Year Consumer WarrantyPage 8

Rev.: 20100302



Documents

Platform: XK09 Firmware: DLCH3 - Microsoft Neon & PT Cruiser will be selected for programming. Must press and hold the Programming button for 3 seconds to select a type. Flashes once