Optimum M4240BLUETOOTH TERMINAL INSTALLATION GUIDE

© 2011 Pivotal Payments Direct, all rights reserved. Hypercom and Optimum and Design are registered trademarks of Hypercom Corporation. The Hypercom logo is a trademark of Hypercom Corporation. All other products or services mentioned in this document are trademarks, service marks, registered trademarks or registered service marks of their respective owners.

www.pivotalpaymentsdirect.comwww.pivotalpaymentsdirect.com

COMPLIANCEChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications to the product(s) identified in this manual unless expressly approved by Hypercom could void the user’s authority to operate these product(s).

• ICES-003 This Class A digital apparatus complies with Canadian ICES-003. CET appareil Numerique de la classe A est conforme a la norme NMB-003 du Canada.

• PCI-PED Legal Terms and Conditions PCI SSC’s approval only applies to PEDs that are identical to the PED tested by a PCI Security Standards Council recognized laboratory. If any aspect of the PED is different

from that which was tested by the laboratory — even if the PED conforms to the basic product description contained in the letter, then the PED model should not be considered approved, nor promoted as approved. For example, if a PED contains firmware, software, or physical construction that has the same name or model number as those tested by the laboratory, but in fact are not identical to those PED samples tested by the laboratory, then the PED should not be considered or promoted as approved.

No vendor or other third party may refer to a PED as “PCI Approved,” nor otherwise state or imply that PCI SSC has, in whole or part, approved any aspect of a vendor or its PEDs, except to the extent and subject to the terms and restrictions expressly set forth in a written agreement with PCI SSC, or in an approval letter. All other references to PCI SSC’s approval are strictly and actively prohibited by PCI SSC.

When granted, an approval is provided by PCI SSC to ensure certain security and operational characteristics important to the achievement of PCI SSC’s goals, but the approval does not under any circumstances include any endorsement or warranty regarding the functionality, quality, or performance of any particular product or service. PCI SSC does not warrant any products or services provided by third parties. Approval does not, under any circumstances, include or imply any product warranties from PCI SSC, including, without limitation, any implied warranties of merchantability, fitness for purpose or noninfringement, all of which are expressly disclaimed by PCI SSC. All rights and remedies regarding products and services, which have received an approval, shall be provided by the party providing such products or services, and not by PCI SSC or the payment brand participants.

• CE (Select Models) - IEC 60950-1 - EN 55022 - EN 55024 - EN 60950

• A-tick (Future Planned)• RoHS

• UL/cUL Listed (UL 60950)• WEEE

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Information About Bluetooth Access PointBluetooth wireless technology is a short-range communications technology intended to replace the cables connecting portable and/or fixed devices while maintaining high levels of security. Hypercom’s Bluetooth access points provide centralized communications for the Optimum M4240 terminal. Each access point has a wireless range support of up to 500-1000 meters (1640.42-3280.80 feet), in a direct line of sight & can communicate simultaneously with up to seven Optimum M4240 terminals.

500-1000 meters (1640.42-3280.80 feet) in direct line of sight

For more information, see the Optimum M4240 Bluetooth Access Point Installation Guide. Access PointOptimum M4240

Information About Docking StationAn optional docking station (Standard) is available for the Optimum M4240 terminal. The docking station provides a convenient and stable place to store and re-charge your terminal. When the terminal is placed on the docking station, normal operation can continue while the battery is being charged, with no interruption of service. It can also be used to pair one terminal to a Bluetooth access point. Note: All power and communication cables must be removed from a terminal before placing it on a docking station.

For more information, see the Optimum M4240 Bluetooth Access Point Installation Guide. Optimum M4240

Docking Station

Pivotal Payments Direct, 14 Commerce Place, St. Catharines, Ontario, Canada, L2R 6P7

PIVOTAL_Optimum_M4240_Installation_Guide.indd 1 11-04-28 15:44

Optimum M4240 Bluetooth Terminal Installation GuideEquipment Check List

Battery Installation Receipt Paper Installation

Optimum M4240

The Optimum M4240 Bluetooth Terminal Installation Guide provides basic setup information. Your device also comes pre-installed with a Lithium Ion Battery Module (7.4V - 1.88Ah). Once fully charged, the battery can complete more than 200 transactions before requiring another charge.Note: Charge the battery for 2-4 hours before initial use of the terminal. Charging indicator turns green when terminal battery is fully charged.

The Optimum M4240 requires at least one access point to communicate successfully. See the Accessories Available section for more information or contact your Hypercom Sales Associate for specific options and regional availability.

Note: Images within this guide may not exactly match your device.

Accessories Available

Optimum M4240 (P/N# 010341-005R

For All Regions)

2

Docking Station (P/N# VE018-2007)

AP110 Ethernet Access Point (P/N# VE018-2005)

Lithium Ion Battery Module (P/N# 400037-001)

Drop paper roll into paper holder (as shown). Pull paper (as shown) & close printer cover.

1

With your fingers, open the printer cover (as shown).

Printer Cover

Pull Receipt PaperDrop

Paper Roll

3

Pull & tear paper against the paper receipt guide. Operate terminal as normal.

Paper Receipt Guide

Insert Your Smart Card

Paper Roll (P/N# 710015-003)

Paper Roll

Privacy Shield (P/N# 040348-001

meets PCI compliance)

Swipe credit card through the card reader with a downward or upward motion (as shown).

1

Credit Card

Bi-directional Card Reader

Swipe Your Credit Card

Optimum Developer’s Toolkit(P/N# 010305-xxx)

1

Turn the terminal over. Remove the battery by squeezing the inset on the right side of battery (as shown).

2

Remove and discard the plastic covering surrounding the battery. Re-insert the battery.Note: Connect power and charge battery 2-4 hours before Power On. Indicator light turns green when fully charged.

Battery

A/C Power Adapter (P/N# 870075-xxx)

Region Specific

Clean Your Device

Apply water or plastic-safe cleaner onto a soft, lint free cloth and gently wipe terminal.

1

MSR Slot

Optional Smart Card

Reader

1

Turn the terminal over to display labeled ports (as shown):- POWER port = A/C Power Adapter - SERIAL port = RS232 cable

Labeled Ports

Power Connection

2

Insert A/C Power Adapter into POWER port (as shown). Insert other end of the Power Cord into the wall receptacle. Battery starts to charge.

Power On/Off1

Turn the terminal over. To Power On/Off the terminal, press and hold the blue FUNCTION key until you hear a beep (approximately 5 seconds).

Press FUNCTION Key

Insert smart card (gold chip side up) into the smart card reader (as shown).

1

Smart Card

Optional Smart Card

Reader

Warning: • Only use the provided Hypercom power adapter. Non-compliant power adapters may damage the device. • Do not use if visibly damaged. • Do not expose to temperatures above 140 °F (60 °C) or below 14 °F (-10 °C). • Do not disassemble. • Do not incinerate or crush. • Do not power ON terminal in a flammable atmosphere, such as petrol station, chemical depot, etc. • Keep out of reach of children and pets.

Region Specific

A/C Power Adapter(or equivalent L.P.S. type)

Only use the Hypercom power adapter.

WARNING:• Do not use industrial strength cleaner or an abrsive cleaner as it may damage or scratch the screen• Do not immerse device in water (or liquid)• Do NOT spray water or cleaner into the MSR slot, Smart Card Reader or ports on the back.

PIVOTAL_Optimum_M4240_Installation_Guide.indd 2 11-04-28 15:44