TOTAL W.O

LE

T

219.80 Sch. 90º 45º 90º 45º 90º 45º EQ. CO/10S 40 80 150# 300# 600# 900#

###

1Os 10 20 30 40 80 10S 40 80 10S 40 80 10S 40 80

m m m m m m pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs

½" ###

¾'' ###

1'' ###

1½'' ###

2'' ###

2½'' ###

3'' ###

4'' ###

5'' ###

6'' 5.0 2 1.0 2.0 ###

8'' ###

10'' ###

12'' ###

14'' ###

16'' ###

18'' ###

20'' ###

22'' -

24'' ###

26'' ###

28'' -

30'' ###

32'' -

34'' -

36'' ###

38'' -

40'' ###

42'' ###

44'' -

46'' -

48'' ###

CRISTIANELBOW TEE Reducer CAP WN FLANGE PIPE

Main DIAMETER Branch Diameter

2xR 2xr

1219.2 609.6

1219.2 609.6

Suplimentary length to be cut out.x VALUE 527.93 mmw VALUE 557.30 mm

R -x = 81.6709ThicknessQuoted Length 845

Branch Length 318.07 ANGLE 90°

Branch Length 287.70 ANGLE 45°

rx

ENTER DATA

Main pipe = 20" 45º branch = 8"

Main pipe = 22"90º branch = 20"

© Iuhas Cristian Bonny -Island 2001

ANGLE 90°

ANGLE 45°

ENTER DATA

© Iuhas Cristian Bonny -Island 2001

Trunion

ADITIONAL LENGTHx = 101.80

H = 134.58

QUOTED LENGTH90

CUTTING LENGTH191.80

Elbow 90º

Drawing : Irimia AntonProgram: Cristian Iuhas

Bonny Island 2001

Particular case: 14" ELBOW 900 with 10" TRUNION

R = 4" Head pipeB = 4" BranchD1 = 228 mmE = Full encirclement

shall be used.VENT HOLE

Pad material shall be the same as the main pipe.

Reinforcement pads may be divided into halves

with a longitudinal welded seam, and ventholewith a longitudinal welded seam, and vent hole on each half. on each half.

Branch attachement welds shall be in accordance

with ANSI B31.3

For sizes not shown, consult with sttress analyst.

12

3

4

NOTE :

BRANCH 90º

NOMINAL SIZE

BRANCH 45º

NIGERIA LNG PROJECT

SHELL STANDARD FOR REFINERY COMPLEX.

Reinforcing pad thickeness shall not be less than the thicknes of the header. The reinforcing pad material shall be the same nominal material as the header and equal or higher stress value.

1. The reinforcing pad width 'L' shall not be less than that specified .2. The pad shall be positioned so that the top of the pad extends an equal distance from outside surface of the branch on either its side.

WIDTH ' L' [mm]

© Iuhas Cristian Bonny -Island 2001

214.30 mm261.64 mm

Pad material shall be the same as the main pipe.

Reinforcement pads may be divided into halves

with a longitudinal welded seam, and ventholewith a longitudinal welded seam, and vent hole on each half. on each half.

Branch attachement welds shall be in accordance

with ANSI B31.3

For sizes not shown, consult with sttress analyst.

BRANCH 90º

NOMINAL SIZE

BRANCH 45º

NIGERIA LNG PROJECT

SHELL STANDARD FOR REFINERY COMPLEX.

1. The reinforcing pad width 'L' shall not be less than that specified .2. The pad shall be positioned so that the top of the pad extends an equal distance from outside surface of the branch on either its side.

WIDTH ' L' [mm]

© Iuhas Cristian Bonny -Island 2001

RAPID CALCULATOR

57 mm ADD EXTR. ADD EXTRACT RESULT236 57 4642205 57

76 mm 6270 350350 SS

57 mm 300 2"-20"140 mm 402 24"

334 30"273.00 485136.50 190 CS&ITCS

6.35 200 2"- 16"240 >18"

127 1750440

555

660.00

13957

464

SCH

SIZE

RED.

TEE

FLANGE

O.D.

THK½ OD

WELDOLET

© Iuhas Cristian Bonny -Island 2001

ELBOW

VALVE

DELETE

CLEAR

6m - 8m 6 m

12m | 6m6m

CS&ITCS11m-13m 12m

© Iuhas Cristian Bonny -Island 2001

NIPOFLANGE

SIZEWEIGHT [Kg]

150 300 600½" 3.421" 4.09 4.79 5.49

1½" 7.72

NIPOLET½" 1.921" 2.99

1½" 4.42 Kg

RANDOMS SIZECS 3" 4" 24"

11954 12053 11835

12055 12042 11825

11957 12045 11830

SS 6" 10" 20" 24"6020 6560 6020 6015

6295 6042 6020

6710 6045 6025

6785

ITCS 2" 6" 8" 18"12045 13043 13500 9225

13138

12972