PICTURE TO COME · source hyd leaks, replaced trans input seal 2014/01/16-cs paul austin clark clean off plate, drill, tap and install fittings-look for hose-found @ aurora laydown

Negotiated sales for heavy equipment & industrial assets

2005 Caterpillar 777D

Year 2005 Manufacturer CaterpillarModel 777DAsset Type Rock TruckSerial Number EAGC01626Usage 29,512 hrsComes with retarder, A/C, liner, heated box, auto lube, 27.00R49

rbauction.com/privatetreaty

Asset 11

Don’t miss out! Contact Scott Zeilstra to make an offer:+1.780.686.0725 [email protected]

PICTURE TO COME

COMPONENT

CHANGES

SERVICE REPORTS

WORK ORDER HISTORY

Maintenance History for Equipment ID: RDC004Start Date Meter Reading (Hrs)Job Number / Description

4-Jan-2016 WOC259662 - PREP FOR SALE 29,512Prep for Sale

1-Oct-2015 WOC258961 - SRV > CHANGE DIFF & FINAL OIL 29,509CHANGE DIFF & FINAL OIL

26-Aug-2015 WOC258695 - PERFORM ENGINE VALVE SET 29,299.

20-Aug-2015 WOC258612 - SRV > 250 HR 29,281CARRY OUT 250HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:

SERVICE CARRY OUT BY:

MAGNETIC PLUG REPORT:

LHF/FD:RHF/FD:F/DIFF:LHR/FD:RHR/FD:R/DIFF:

ALL DEFECTS ENTERED INTO GP.

1-Jul-2015 WOC258379 - TYR > FY2016 PREPAID TIRES 29,095

1-Jul-2015 WOC257857 - 2016 R&M - JUL 1 TO JUN 30 29,004

23-Jun-2015 WOC257657 - SRV > CHANGE DIFF & FINAL OIL 29,281CARRY OUT DIFF AND FINAL OIL CHANGE

10-Jun-2015 WOC257547 - SRV > 2000 HR 29,281CARRY OUT 2000HRS SERVICE AND REPAIRS AS REQUIRED

13-May-2015 WOC257209 - SRV > 1750 HR 28,937CARRY OUT 1750HR SERVICE AND REPAIRS AS REQUIRED

8-Apr-2015 WOC256652 - FIRE SUPPRESSION PM 28,600.

24-Oct-2014 WOC241978 - BRAKE AND STEERING TEST 28,587.

1-Jul-2014 WOC254492 - TYR > FY2015 PREPAID TIRES 28,645

1-Jul-2014 WOC254177 - 2015 R&M - JUL 1 TO JUN 30 28,645

1-May-2014 WOC253401 - PERFORM ENGINE VALVE SET 29,294

Page 1 of 39Emeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com Printed on: 12-Jan-2016

Meter Reading (Hrs)Start Date Job Number / Description

Maintenance History Continued for Equipment ID: RDC004

.

8-Mar-2014 WOC216933 - PERFORM ENGINE VALVE SET 948.

4-Mar-2014 WOC238420 - FIRE SUPPRESSION PM 28,600.

1-Jan-2014 WOC246523 - 2014 R&M - JAN 1 TO DEC 31 28,631




2014/01/10-OT-ELJOHN HOLLOWAYASSISTED WITH DEFECT REPAIRS. STARTED DOING PARTS LIST.

2014/01/10-OTDAVE DEFEHRTOOK APART, CLEANED AND RE SEALED GREASER. INSTALLED AIR FITTING

2014/01/15-TAKODY MCGUINNESSDROVE TO SITE. DROVE BACK TO FT.MACKAY. WAITED AT ID STATION

2014/01/15-FR-ELPAUL AUSTIN CLARKREMOVE OLD BENT BRACKETS AND STEPS ON R.H SIDE, C/O RUBBERS ON L.H SIDE TO MATCH UP.C/O AIR FILTERS. CHECK AND TEST BATTERIES, FOUND BATTERY CLAMP BROKEN SO REPLACED.

2014/01/15-ST-CSPAUL AUSTIN CLARKREMOVE STEERING TIE RODS. R.H AND L.H. DRAIN COOLING SYSTEM. RE START, REROUTE OF HOSE

2014/01/15GARTH JOHNSONREMOVE GUARDING AND U-JOINT BOLTS. REMOVE OLD TRANSFER CASE INPUT SEAL. CLEAN PARTS.REMOVE GUARDING FOR TORQUE CONVERTOR U-JOINT. POP STEERING ROD BALL STUDS FROM 4CONNECTOR

2014/01/16-OTED CORRIGALREMOVE TOP STARTER TO EXPOSE COOLANT GALLERY. DISCONNECT NEGATIVE BATTERY CABLE. REROUTE COOLANT HOSE TO NEW AREA. CAP OFF EXISTING COOLANT VALVE

2014/01/15-OTED CORRIGALTAKE OUT EXISTING PASSENGER SEAT BELT AND BUCKLE AND INSTALL NEW ONE. DRAIN COOLANTFROM UNIT AND HOLD IN COOLANT CUBE. INSTALL FOOT STEPS ON FRONT OF UNIT

2014/01/16-OT-HYDON GRENIERREPLACED SLIDES IN THE OPERATERS SEAT. SOURCE HYD LEAKS, REPLACED TRANS INPUT SEAL

2014/01/16-CSPAUL AUSTIN CLARKCLEAN OFF PLATE, DRILL, TAP AND INSTALL FITTINGS-LOOK FOR HOSE-FOUND @ AURORALAYDOWN

2014/01/20-EN-CSPAUL AUSTIN CLARKREMOVE FUEL FILL LINE. INSTALL NEW PIPING AND BALL VALVE AS REQUIRED. INSTALL NEW HOSESAND FITTING AS REQUIRED.

2014/01/31-OTAARON CMOVE DOZER AWAY BAY 3, BACK RDC004 OUT OF BAY 3 TAKE ONE TO OTHER YARD LAYDOWN TIRESAND MATTS AND BACK DZC045 OUT OF WASH BAY, LAYDOWN TIRES AND MATTS IN BAY 3 TO BRINGDZC045 IN, PUT LEDCOR D9T INTO WASHBAY

2014/02/03-HCDEVIN BAILEYHOOK UP PORTA THAW. BROUGHT UP TO SHOP. BEGAN REMOVING LIFT CYLINDERS.

2014/02/03-OTJOHN HOLLOWAYHOOKED UP HOT BOX, BOOSTED AMD STARTED UNIT AMD MOVED FROM EAST YARD TO SHOP.

2014/02/03-HCROBERT HEARNATTACH PORTA THAW, GET UNIT PUMING, MOVE TO YARD. START TO REMOVE. HOIST CYLINDERSBATTERY DEAD, NEED TO BOOST/CHARGE BATTERY, AIR SYSTEM FROZEN, PUT ?? IN LINE. PINSEIZED IN BOLE ON HOIST CYLINDER

2014/02/04JOHN HOLLOWAY & ROBERT HEARN & DEVIN BAILEYREMOVED HOIST CYL & PACKAGED FOR SHIPPING

20-Nov-2013 WOC242077 - SRV > 1500 HR 28,721




CARRY OUT 1500HR SERVICE AND REPAIRS AS REQUIRED

13-Nov-2013 WOC243040 - BC > SYN REPLACE CAB 28,608QTM4944

REPAIR ACCIDENT DAMAGEREPLACE CAB

BACKCHARGE TO SYNCRUDE

2013/12/01-BC-28595ROD SHEVALIERFINISH DISCONNECTS, REMOVE CAB, MOVE CABS INTO SHOP. START TRANSFERRING PARTS AND HARNESSES

2013/12/01-BC-28595CRAIG MISANCHUKCAP AND MARK CAB OIL LINES, REMOVE MOUNTING BOLTS, REMOVE FINDERS TO ACCESS BOLTS, RIG AND HOIST CAB OFF UNIT, MOVE CABS INTO SHOP. CLEAN OUT ELECTRICAL BOX BEHIND CAB, BEGIN TRANSFERRING PARTS AND HARNESSES

2013/12/02-BC-28595ROD SHEVALIERREPLACE EVAPORATER, REMOVE CUT LINES. REMOVE HEAD LINER, REMOVE CENTRE CONSOLE. REMOVE CENTRE SHIFT CONSOLE. REMOVE AFTER MARKET WIRING. REMOVE SEATS. REMOVE FIRE SUPPRESSION. REMOVE LUBE TANK CONTROLLER. INSTALL ALL PARTS REMOVED FROM ?? CAB TO USED ONE. INSTALL PROPER WIRING

2013/12/02-BC-28595CRAIG MISANCHUKSTRIP DAMAGED CAB WIRING, ECMS ADD ON'S STEREO, AIR SYSTEM, MARKED AND TOOK PICTURES AS i WENT ALONG. STARTED REMOVING MAJOR PARTS FROM REPLACEMENT CAB ECM'S WIRING. ORDERED BOSSES TO BE WELDED IN REPLACEMENT CAB FOR MOUNTING ?? ADD ONS THAT WERE DAMAGED CAB. CLWAN UP TOOLING AND SWEEP UP WORK AREA @ END OF SHIFT

2013/12/12-BCROD SHEVALIERTIGHTEN CAB MOUNT BOLTS. START CAB HOOK UPS, LINES AND WIRING

2013/12/12-BCCLAUDE BELISLEINSTALLING FINNISHING CAB MOUNTS, MUDD FLAPS AND HYDRAULIC HOSES.

2013/12/13-BCCLAUDE BELISLEFINISH INSTALLING CAB, HOSES AND RAILING. INSTALL HYDRAULIC LINES HEATER HOSES, AIR CONDITONING HOSE. COVER ON FRONT.

2013/12/13-BCROD SHEVALIERCONNECT AIR LINES. CONNECT CAB WIRING, OVERSIZE CANNON PLUG MOUNTING HOLES AND INSTALL. REPAIR WIRE CONNECTIONS. START UNIT AND WARM UP. CHECK FUNCTIONS AND SWITCHES

2013/12/15-FIX CAT WALKROB YOUNG - IRON SMITHFIXING WALK WAY

24-Oct-2013 WOC209904 - BRAKE AND STEERING TEST 28,518.

15-Oct-2013 WOC238811 - SRV > 1250 HR 28,580





ENGINE HOURS:

DATE:


MAGNETIC PLUG REPORT



2013/09/24-SLTYLER MACEACHERNBACKFILLED 50 W OIL IN LUBE TRUCK TO PREP FOR DIFF SERVICE ON RDC004. DID NOT DOSERVICE TODAY.

4-Sep-2013 WOC208085 - FIRE SUPPRESSION PM 28,105.

24-Aug-2013 WOC236369 - SRV > 1000 HR 28,105CARRY OUT 1000HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013/09/07 - SL - 28105MARTY HOFF1000HRS SERVICE. CLEAN UP AREA. BACK FILL TRUCK.

2013/09/07 - SL - 28105MELVIN BUTLER1000 HR SERVICE. CLEAN UP SITE. CRUSH USED FILTERS.

6-Aug-2013 WOC236093 - SRV > 750 HR 27,809





ENGINE HOURS:

DATE:





2013/08/09 - 27809 - SLMARTY HOFF750 HR SERVICE. CLEAN UP AND BACK FILL TRUCK

12-Jul-2013 WOC230798 - SRV > 500 HR 27,500CARRY OUT 500HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013/07/15 OTHER/SERVICE LEE MEISECHANGE OUT 3 OIL CUBS IN LUBE TENT. CLEAN OUT LUBE TRUCK. BACK FILL OILS. 500 HR PM.

2013/08/08 - SLMELVIN BULTERWAITED FOR PLACEMENT TO GIVE UP TRUCKCAN'T GET RDC004 UNTIL TRUCKS THT ARE DOWN ARE FIXEDTRANSFERRED FILTERS FROM ONE C-CAN TO THE NEW ONE.

25-Jun-2013 WOC231775 - REMOVE & INSTALL DIFFERENTIAL 27,273REMOVE AND INSTALL DIFFERENTIAL USING PSC STOCK.DIFFERENTIAL CHANGE UP DUE TO EARLY FAILURE

2013/06/24 DRIVE LINEKEVIN LOWREMOVE DIFF AND TRAINING

2013/06/26 DRIVE LINEDARREN JEFFRIESASSIST TYLER, TOP UP FLUIDS, REPLACE SYNCRUDE FUEL FITTNG, INSTALL STEERING CAP, REPLACE ROBBED TRANS INPUT SENSOR AND TEST DROVE UNIT AROUND LAYDOWN - OK, CALLED UNIT UP

21-Jun-2013 WOC231311 - INSTALL VISIONLINK GPS 27,497.

27-May-2013 WOC210708 - SRV > 250 HR 27,212





ENGINE HOURS:

DATE:





4-23-2013- SERVICEMELVIN BUTLERDRAIN FUEL TANK, TOP UP HYD TANK, EVAC HYD OIL FROM WASTE CONTAINER

4-23-2013- SERVICEMELVIN BUTLERDRAIN FUEL TANK, TOP UP HYD TANK, EVAC HYD OIL FROM WASTE CONTAINER

2013-06-16 SERVICEMARTY HOFF250HR SERVICE, CLEAN UP AREA, DISPOSED OF WASTE

10-May-2013 WOC222350 - FRONT TIRE INSTALLATION 26,701.

8-Apr-2013 WOC200571 - 2000HR SERVICE 26,620CARRY OUT 500HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013-04-15- SERVICEMELVIN BUTLER

2013-04-15- SERVICEMELVIN BUTLER2000 HR SERVICE, CLEAN UP SITE, CRUSH USED FILTERS, DISPOSE OF USED OIL

2013-04-15- 2000 HRTYLER MACEACHENCOMPLETED 2000 HR SERVICE, DRAINED AND FILLED FINALS HUBS DIFF, CHECKED ALL LEVELS, CLEANED LUBE TRUCK, COMPLETED SAMPLE PAPERWORK, BACK FILLED TRUCK

2013-04-16- SERVICEMELVIN BUTLERBACK FILL 50W, 2000 HR SERVICE, EVAC WASTE OIL, CRUSH USED FILTERS

2013-04-16- 2000 HR TYLER MACEACHENCOMPLETE 2000 HR SERVICE, DRAIN AND FILL FINALS HUBS DIFF, CHECK ALL LEVELS

2013-04-17- SERVICEMELVIN BUTLEREVAC WASTE OIL TANK, BACKFIL OW40




6-Apr-2013 WOC178350 - FIRE SUPRESSION RECERT 26,612PERFORM 1200HR FIRE SUPRESSION INSPECTION

APRIL 06, 13 - LEVITT1200 HR PM COMPLETED

17-Feb-2013 WOC190046 - BC OILS TO KMC 26,131QUOTE# QTM QTM4331

BACK CHERGE OILS ONLY TO KMC

2-Jan-2013 WOC175021 - JAN 2 - DEC 31 2013 R&M WO 25,144




**************

2013-01-20 STEERING BALL STUDGRANT OSMANLOAD BOOSTER BATTERIES, HUNT FOR SPARE STEERING CYLINDER IN YARD, UNABLE TO FIND, 30MIN, TVL TO SITE, SIGN IN AT KMC, TVL TO ENTRANCE D GET PERMIT & AUTHORIZATION FROM LH,TVL TO MACHINE, LOAD CHECKS & FLRA, REMOVE STEERING CYL OIL LINES, REMOVE BALL STUDFROM FRAME, SAME DIFFICULTY WITH THIS DUE TO EXTREME COLD ON AIR IMPACT TOOLS, FOUNDBEARING FOR BALL STUD NOT SEATED, SEAT BEARING INSTALL ROPE RETAINER CLIP, REASSEMBLESTEERING CYL ON UNIT, HOOK UP OIL & GREASE LINES, CHECK AUTO GREASER OK, TVL TO KMCLAYDOWN

2013-01-17 -GRANT OSMANORDER PARTS HEATER MOTOR & RESISTOR, PICK UP AT KMC WAREHOUSE, TVL TO D, GET DRIVINGAUTHORIZATION, WAIT FOR CLEARANCE 20 MIN FROM 671 SUNCOR, TVL TO MD-3 TRUCK WASN'TTHERE, RING AROUND TO FIND AT F PANNELL IN TAILINGS, WAIT ALMOST 2 HRS FOR ESCORT,LOCKS & CHOCKS ON MACHINE, CHECK HEATER TAPS BOTH FULL OPEN, FOUND LOTS HEAT ANDBLOWER WORKS ON ALL SPEEDS, TEST HEATER TEMP FOUND 45 C AT 1000 RPM, OK, REPAIR ONEHEADLIGHT, CALLED UNIT UP AT 12:00

2013-01-20- STEERING BALLGRANT OSMANMORNING SAFETY MEETING LOAD BOOSTER BATTERIES, HUNT FOR SPARE STEERING CYL IN EMECOYARD UNABLE TO FIND, TRAVEL TO SITE, SIGN IN AT KMC TRAVEL TO ENTRANCE D GET PERMITAUTHORIZATION FOR 671, TRAVEL TO MACHINE LOCKS , CHOCKS AND FLRA, REMOVE STEERING CYON LINES, REMOVE BALL STUD FROM FRAME, SOME DIFFICULTY DUE TO EXTREME COLD ON AIRIMPACT TOOLS, FOUND BEARING FOR BALL STUD NOT SEATED, SEAT BEARING INSTALL CAPERETAINER CLIP REASSEMBLE STEERING CYL ON MACHINE, HOOK UP OIL ANG GREASE LINE, CHECKAUTO GREASE OK, TRAVEL TO KMC LAYDOWN

2013-01-26 -JIM MACFARLANETRAVELED TO KMC SUNCOR ATTEND MORNING PASS MEETING, PICK UP MINE ACCESS PERMIT,TRAVEL TO SITE 1-11 DIRECTED BY SHIFT FOREMAN, MACHINE NOT THERE, TRAVEL TO (*MO4*)MACHINE NOT THERE, TRAVEL TO TRO WORK AREA, FOUND MACHINE, CHECKED LIGHTS AND FOUNDBURNT OUT BULBS, REPLACED BULBS, OK, CHECKED CONNECTIONS OK

2013-02-09 SERVICELEE MEISETRY TO HAVE ANY OF KMC RENTAL TRUCKS BROUGHT TO KMC LAYDOWN YARD, STARTING TOREALIZE THAT KMC DO NOT WANT TO GIVE UP A OPERATOR THAT THEY ARE SHORTHANDEDOPERATOR, TO DRIVE 1 HR TO 1.5 HR CROSS SUNCOR SITE TO HAVE A PM SERVICE DONE ON UNIT,THEN DRIVE UNIT BACK ACROSS SITE

2013-02-11JIM MACFARLANETRAVELED OUT TO MACHINE, REAR SURPRESSOR FLAT CHARGED REAR STRUTS, OIL LEAKING FROMBOTH STRUTS, CHECKED OUT GREASER, OK, REPAIRED

2013-02-01- REAR STRUTSMARK FORANCHARGED BOTH REAR STRUTS, BOTH ARE LEAKING OIL, KEEP AN EYE ON STRUT FOR LEAKING,REPAIRED GREASE LINES

2013-02-22- AIR LEAKGRANT OSMANTRAVEL TO UNIT, FOUND AIR LEAK TO BE CAB AIR DRAIN WAS OPEN, BOTH REAR FLAT, RECHARGEAND SET TO 42" HIGH PACK UP TOOLING FOR NITROGEN

2013-03-02-GRANT OSMANTRAVEL TO MACHINE, AS DCF SAID DOWN ALL DAY FOR HORN, FOUND HORN CONTACT VERY DIRTY,WORN, CLEAN, REASSEMBLE, TEST OK, CALLED UNIT UP

2013-03-10- SUSPENSIONJIM MACFARLANECHECK MACHINE OVER REAR SUSPENSION CYL FLAT, FILL WITH OIL , CHARGE WITH NITROGEN

2013-03-14- START UNITRAY MURPHYSTART UNIT FOR NIGHT SHIFT

2013-03-20- TOP UP HYD OILLEE MEISECLEAN UP TOOLING AND TRACK IN THIS AREA, DRIVE TO RDC004 TO FILL UP HYD OIL




2013-03-20- HYDRAY MURPHYHAD REORDERED TIRE LACE PICK UP AT FINNING

2013-03-19- HYDRAY MURPHYUNIT WAS LOADED HAD TO GET KMC TO UNLOAD TRUCK, CHECK LEAK FOUND LEFT BACK CYLLEAKING AND NEEDING TO GET PARTS, WENT TO FINNING BUT WAS NOT READY WAITING FOR IT TOBE MADE

2013-03-25-JIM MACFARLANEINSHEET INSPECTION

2013-04-05- PARTS ORDERJIM MACFARLANEORDER PARTS FOR SEVERAL UNITS

2013-04-06- START UNIT, REMOVE WINTER FRONTDON PELLERINSTART UNIT FOR FS GUYS, WOULD NOT START, ASSISTED IN STARTING UP, REMOVED WINTERFRONT, CLEAN UP YARD

2013-04-07- INSPECT TRUCKDON PELLERINGCLEAN HOIST VALVE, HAD WELDER SHAKE TRACK WELL INSPECTING PARTS, OK,

2013-04-09- REPAIRSJIM MACFARLANEBATTERIES DEAD, CHARGED BATTERIES START UNIT, WARM , CLEAN WORK PAD MOVE MACHINEONTO PAD, END OF DAY

2013-04-09-DARREN FITZGERALDUNIT NEEDED TO BE MOVED ONTO RIGH MAT FOR REPAIRS, FOUND UNIT HAD DEAD BATTERIES,CHARGED BATTERIES AND WARMED UP UNIT, CLEANED OFF RIG MAT AND MOVED INTO POSITIONTO START REPAIRS

2013-04-19HARREY OTTESENLOAD TRUCK WITH TOOLS, MOVING STEAM TRAILER TO BASE MINE, REMOVE GUARDS AND DRIVELINE PIN BOX, REMOVE AND INSTALL NEW SEAL

2013-04-10- ENPAUL HICKSCLEANED OFF THE AREA AND RAN THE UNIT AND CHECKED OUT THE LEAK, STARTED TO REPLACETHE STARTER GASKET

2013-04-11- POWER TRAINGRANT OSMANTRAVEL TO SYNCRUDE FROM SUNCOR, SET UP A MACHINE LOCKS AND CHOCKS, INSTALL DRIVESHAFT AND T/O BOLTS TO 430LBS, TRAVEL OFF SITE

2013-04-19- BOXIRONSMITHREPAIR CORNER TAIL END BOX

2013-04-19GRANT OSMANMOVE MACHINE FROM MUD HOLE BY SEA CANS, RAISE, PIN TRUCK BOX, HELP WITH OUTSHEETCHECKS, SORT THROUGH PARTS, NEUTRAL RUN PILOT LIGHT NOT WORKING, FOUND WIRE BROKENAT BACK OF BULB HOLDER , REPAIR AND REASSEMBLE

2013-04-19DANNY HILLIERREPAIR GREASE LINE ON L REAR STRUT, STARTED UNIT AND MOVED DRYER LOCATION, TIED UPHOSES THAT WERE HANGING UNDER ENG, STARTED OUTSHEET INSPECTION, REPAIREDWINDSHIELD WASHER

2013-04-19HARLEY OTTESENSET UP MACHINE INORDER TO REMOVE REAR STRUTS, REMOVE RH REAR STRUT AND RESEAL

2013-04-21HARLEY OTTESEN




INSTALL RH REAR STRUT, BLOCKING UP UNIT INORDER TO PULL TOP PIN OUT OF LH REAR STRUT

2013-04-22HYD CYLGRANT OSMANPICK UP , TRAVEL TO BASEMINE, LOCKS AND CHOCKS , FLRA, REMOVE TOP LEFT STRUTT PIN SIEZEDPIN, VERY TIGHT, HEAT TO REMOVE, REMOVE CYL AND RESEAL, RESEAL BOTH CHARGE VALVES , OILBOTH STRUTTS USING, PARK BRAKES, RELEASE OIL, SET UP TO CHARGE

2013-04-22HARLEY OTTESENOIL AND CHARGE REAR STRUTS AND LH FRONT STRUT TO SPEC, HAD TO MAKE TRIP TO AURORA TOLOOK FOR XHC080

2013-04-23 ENGGRANT OSMANDRAIN FUEL TANK, REMOVE WIGGENS, MAKE UP PIPE, WORK FOR TANK, MAKE 32 REUSABE HOSE TOFIT, WELD ON WIGGENS BOX ON HYD TANK, INSTALL VALUE, WIGGENS AND HOSE ENDS , INSTALLHOSE, WELD ON BOSSES, AND INSTALL TAB CLAMPS TO MOUNT, FILL WITH FUEL, OUTSHEETCHECKS, BRAKES LIGHTS, STEERING CHECKS, MOVE TRUCK AND CLEAN UP AFTER STRUTT REPAIRS

2013-04-23ENGRYAN ELLISTRAVEL TO B/M, MAKE AND INSTALL UNIT NUMBERS, CHANGE ORING ON BREATHER FOR ENGINE,FINISH OUTSHEET, CHANGE ORING ON STEERING HOSE, CLEAN CAB

2013-04-27KEVIN LOWT/S BOX UP OVER RIDE PROBLEM, FIX WIRING AND CHANGE SWITCH, TEST RUN UNIT, CHECK OVER

2013-05-05-KEVIN LOWWARM UP UNIT, TAKE OIL SAMPLES OF DIFF, R/H FINAL, TRANNY CHECK LEVELS

2013-05-09-HARLEY OTTESENCHECK OUT AND REPAIRED FRONT SIGNAL LIGHTS, CHECKED OUT HOIST COMPLAINT , COULD NOTFIND ANYTHING WRONG WITH UNIT, RETURNED TO WORK

2013-06-14 ELPAUL HICKSI CHECKED OUT THE LOW BEAM LIGHTS ON THIS UNIT AND THE RH LIGHT WAS BLOWN I REPLACEDTHE BULB AND IT WAS WORKING FINE.

2013/06/14 - ENGINELAWRENCE SLACKCLEAN OFF MUD TO SEE GUARD, CUT AND MODIFY GUARD FOR QUICK FILL TO NOT RUB STEERINGTIER, WELD

2013-06-14JIM MACFARLANETIRE RUBBING ON FUEL WIGGINS GUARD, WELDER MODIFIED GUARD, WATER IN AIR SYSTEM DUGOUT MUD AND DRAINED AIR SYSTEM, OPERATOR COMPLAINED OF NOISE IN DIFF, CHECKED ALLLEVELS OK CHECKED MAGNETIC PLUGS OK RUN UNIT NO NOISE

2013/06/22 SERVICETYLER MACEACHERNEVACED DIFF OIL FROM RDC004, MACHINE NEEDS DIFF REPAIRED

2013/06/20 ELECTRICALRAY MURPHYCHECKED OUT AND FOUND WIRE PULLED OUT OF LIGHT, PLUGGED WIRE BACK IN AND CHECK LIGHTAND WIRE WERE STARTING TO PULL OUT TOO, CLEAN MUD OFF HARNESS

2013/06/20 DRIVE LINEKEVIN LOWRUN TO UNIT, T/S NOISE IN REAR END, FOUND PARTS OF GEAR TEETH IN DIFF HOUSING

2013/06/21 DRIVE LINERAY MURPHYMOVED UNIT BACK TO LAYDOWN AND REMOVED TRANS SPEED SENSOR FOR RDC043 DRAINED OILOUT OF DIFF AND FOUND PIECES INSIDE DIFF TO BIG TO COME OUT DRAIN

2013/06/21 DRIVE LINEDARREN JEFFRIESDROVE TO FINNING, PICKED UP PARTS, DROVE TO SYNCRUDE BASEMINE, DROVE TO UNIT WITH RAYAND MOVED RDC004 TO OUR LAYDOWN, DROVE TO NEXT UNIT




2013/06/24 DRIVE LINETRAVIS GRUNERUDGEAR UP AT SHOP, TRAVEL TO BASEMINE, SETUP FOR LIFT, REMOVE DIFF BOLTS AND LIFTCOMPONENT OUT, LOAD COMPONENT AND TRAVEL BACK TO SHOP, UNLOAD COMPONENT

2013/06/22 DRIVE LINEKEVIN LOWWASH AROUND TRANNY AND DIFF, FUEL UP GENSET AND LIGHT PLANTS, DRAIN FUEL OUT OF ATRUCK IN LAYDOWN, SHIRT ON DIFF REMOVAL, UNHOOK LINES AND WIRING, DRIVE SHAFT ANDGUARD, PULL AXLES

2013/06/25 DRIVE LINEROB NICOLLEREMOVED OIL DIFF AND INSTALLED NEW ONE ON TRANS IN SHOP

2013/06/25 TRANSMISSIONTRAVIS GRUNERUDGEWAR UP AT SHOP, TRANSPORT TRANS/DIFF TO BM, RIG UP AND LIFT INTO PLACE, INSTALL NUTSON HOUSING AND TIGHTEN, CLEAN UP WORK AREA, TRAVEL BACK TO SHOP

2013/06/24 DRIVELINETRAVIS GRUNERUDGEAR UP AT SHOP, TRAVEL TO BM, SET UP FOR LIFT, REMOVE DIFF BOLTS AND LIFT COMPONENTOUT, LOAD COMPONENT AND TRAVEL BACK TO SHOP, UNLOAD COMPONENT IN SHOP

2013/06/26 SERVICETYLER MACEACHERNFILLED DIFF OIL - 192L-50W, FILLED LEFT AND RIGHT FINAL, TOPPED UP TRANSMISSION OIL ANDCHECKED ALL LEVELS

2013/06/26 DRIVE LINEKEVIN LOWRUN WASH TRAILER BACK TO SHOP AND REFILL, LOAD UP DIFF AND TRANNY AT SHOP, CLEANHOUSING AND INSTALL TRANNY AND DIFF, HOOK UP HOSES, HARNESSES, DRIVE LINE ANDGUARDS, REINSTALL AXLES AND COVERS, PUT SYNCRUDE GREASE FITTINGS BACK ON THAT WASTAKEN FROM RDC023

2013/06/27 ELECTRICAL/OTHERDARREN JEFFRIESDROVE TO UNIT, OPERATOR HAD SAVED THE MIRROR, SET UP AT UNIT AND SILICONED IT BACKINTO BRAKET, USED TAP TO HOLD IT WHILE THE SILICON SET UP, REPAIR BURNED OUT HEADLIGHT,CALL UNIT UP

2013/07/02DARREN JEFFRIESSET UP AT UNIT, FOUND TWO GREASE LINES BROKEN, ONE ON LEFT UPPER HOIST CYL HAD ABROKEN FITTING, REMOVED AND REPLACED, ONE ON RIGHT INNER TIE ROD END ALSO HAD BROKENFITTING, REPLACED IT, HAD TO TIE ALL STEERING GREASE LINES UP DUE TO ALL THE WEIGHT ONTHEM

2013/07/05 HYDRAULICSHARLEY OTTESENCHECKING OUT HOIST CIRCUIT - ALL AT SPEC. GOT OPERATOR TO RUN UNIT TO CHECK OUTOPERATION - ALL CHECKED OUT OK

2013/07/05 HYDRAULICSPAUL HICKSHAD TO CHIP AWAY A LOT OF MUD TO GET AT THE CONTROL VALVE. HOOKED UP PRESSURE GAUGESAND CHECKED THE HIGH AND LOW PRESSURES AND ALSO THE CONTROL PRESSURES. THE BODYLOWER PRESSURE WAS AT SPEC AT 500PSI AND THE BODY PRESSURE WAS 2800PSI CONTROLPRESSURE WAS OPERATING CORRECTLY WHEN THE SOLENDOIDS WERE OPERATIED. CALLED 4418AND ASKED IF THEY COULD PUT A LOAD OF SAND IN THE UNIT SO THAT IT COULD BE TESTED WITHA LOAD. THEY HAD GOTTEN A LOAD BEFORE SHIFT CHANGE

2013/07/08 HYDRAULICSHARLEY OTTESENCALLED TO UNIT BECAUSE IT WOULDNT GO INTO GEAR UNDER THE LOADER. FOUND HYD TANKEMPTY. FILLED TANK AND REMOVED AND BLOCKED OFF HOIST LINE. ORDERED HOIST LINE

2013/07/09 HYDRAULICSKEVIN LINDSAYREPLACE LEAKING HYDRAULIC HOSE ON LEFT SIDE HOIST

2013/07/13 HCRAY MURPHYCHECK FRONT STRUTS AND CHANGED




2013/07/16 COOLING SYSTEMHARLEY OTTESENREPAIR COOLANT LEAK

2013/07/17 COOLING SYSTEMDARREN JEFFRIESPICKED UP PARTS. INSTALLED NEW HOSE ON UNIT. MARTY TOPPED UP.

2013/07/19 - 27514 - ENGINEKEVIN LOWCHANGE FUEL FAST FILL. CHECK OVER UNIT, FIX REAR RUNNING LIGHTS OUT. CLEAN UP MORESTEEL AND GARBAGE. LOAD AND UNLOAD BACK AT SHOP.

2013/07/28DARREN JEFFERIESDROVE TO SITE-CHECKED TRUCK FOR OVERHEATING. FOUND THAT BRAKE TEMP WAS IN THE RED,LIFTED AND PINNED THE BOX FOUND THAT ALL THE MUD ON THE TRUCK HAD PULLED THE WIRESOUT OF THE SENSOR-CHANGED OUT THE SENSOR. TESTED GOOD-CALLED UNIT UP-DROVE TOLAYDOWN.

2013/0801 - 27673 - ELPAUL HICKSRH FRONT SIGNAL OUT. INSTALLED NEW LIGHT AND CHANGE CONNECTOR ON LIGHT TO HARNESS

2013/08/03 - 27720 - HCHARLEY OTTESENOIL AND CHARGE BOTH FRONT STRUTS

2013/08/07 - 27787 - OTHARLEY OTTESENREPAIR LH BOARDING LADDER

2013/08/12 - 27851 - OTPAUL HICKSCHECKED GREASE HOOK ON REAR. DRILLED OUT BROKEN BOLTS AND BOLTED BACK INTO POSITION

2013/08/16 - 27894 - PPMICHAEL LEEWELK BROKEN HAND RAILS AND BOARDING LADDER

2013/08/16 - 22904 - OTMICHAEL LEEREMOVE DOOR SKIN ON THE INSIDE. WEL CRACKS ON INSIDE OF DOOR AND OUTSIDE AND PUTBACK TOGETHER.

2013/08/18 - EL - 27958KEVIN WEIRCHECK OVER UNITFIX BOTH FRONT MARKER LIGHTS NOT WORKINGTRACE AND FIX WIRINGCHANGE HEAD LIGHT OUT

2013/08/29 - EL - 28077HARLEY OTTESENREPAIRING FRONT SIGNAL LIGHTS

2013/09/01 - CLED CORRIGALDRIVE TO BASEMINE WITH TRAILERS(IDLERS, JACK). MOVE TO RDC 004 ONTO RIG MATS TO STEAM.DRIVE TO WATER TANK WITH TRAILER AND FILL. POWERWASH AND CLEAN RDC 004(ONGOING)

2013/09/01 - OT - 28095PAUL HICKSI CLEARED OFF AN AREA AND SET UPSOME RIG MATS AND THEN POSITIONED THE MACHINE ON THERIG MATS FOR STEAMING. I THEN WENT DOWN AND GOT THE WASH TRAILER FILLED WITH WATER.

2013/09/07 - EL - 28105PAUL HICKSI MOVED THE UNIT FROM THE STEAM PAD TO AN OPEN ARE WHERE THE SERVICE MEN COULD DO ASERVICE AND i ALSO FINISHED THE WIRING TO THE REAR LIGHTS ON THE UNIT.

2013/09/05 - EL - 28105HARLEY OTTESENINSTALLING WIRING AND RELAYS FOR NEW LIGHTING.

2013/09/07 - CL - 28105




ED CORRIGALCLEAN UP PAD AREA WITH LOADER AND BACKSCRAPE. MOVE RDC004 TO WASHING AREA ANDFINISH

2013/09/07 - CL - 28105ED CORRIGALDRIVE TO BASEMINE LAYDOWN. CAB CLEAN RDC004 AND FINISH WASHING. DRIVE BACK TO SHOP.

2013/09/06 - EL - HYKEVIN LINDSAYDIAGNOSE AND REPAIR LIGHTS AND WIRING. REPAIR HYDRAULIC OIL LEAKS.

2013/09/23 BLT/S R/H REAR WHEEL DRAG. CHK WIRING TO REAR WHEEL SPEED SENSORS. CHIP AND CLEAN MUD.UNHOOK BOTH WHEEL SPEED SENSORS, TEST, AND FOUND TO BE OK

2013/09/16 - FR - 28185PIERRE PILOTEWENT TO UNIT AND FIND BOLT ON DOG BONE WAS BROKE. WENT BACK TO LAYDOWN TO REMOVEBOLT FROM RDC043 AND WENT BACK TO UNIT AND INSTALL BOLT IN UNIT.

2013/09/20 HYKEVIN LOWT/S NOISE AT BACK TEST RUN UNIT. FEELS LIKE R/H BRAKE DRAGG. DRAIN R/H, CHK FOR METAL.CHK DIFF FOR METAL, POSSIBLE PARK BRAKE PISTON LEAK.

2013/09/21 FN-2231KEN OLMSTEADCHECK BRAKE PRESSURES 540PSI BRAKES APPLIED. SWAP PLUGS ON DIFF AND CHECK FOR METALTEST DRIVE AND SET LEFT REAR FILL PLUG TO BOTTOM. DRAINED LEFT FINAL AND CHECK FORMETAL.

2013/09/22 DL-28231KEN OLMSTEADREMOVED LEFT FINAL DRIVE COVER

2013/09/24 ELKEVIN LOWSTOP AT FINNING PICK UP PARTS. CHANGR BOTH REAR WHEEL SPEED SENSORS. FILL DIFF ANDBOTH FINALS, TEST RUN UNIT TO SEE IF BRAKE DRAG WAS GONE. ALL OK. CLEAN UP LAY DOWN,WASH AND CLEAN OUT SERVICE TRUCK.

2013/09/24KEN OLMSTEADORDER PARTS TO PICK UP AT FINNING. DOCUMENT #0010728597. TRAVEL TO SYNCRUDE BASEMINE LAYDOWN.

2013/09/25 FNKEVIN LINDSAYASSIST TECHS IN TROUBLE SHOOTING DIFFERENTIAL ISSUES.

2013/09/02 - CLEANINGED CORRIGALDRIVE TO BASEMINE & POWER WASH RDC004STEAM COMPONENTS AND LEFT SIDEDRIVE TO WATER TANK WITH TRAILER & FILLDRIVE BACK TO SHOPTRAVEL PAY $50

2013/09/03 - CLEANINGED CORRIGALDRIVE TO BASEMINE & PICK UP DIRTY COVERALLS, DRIVE TO LAYDOWN & WASH RDC004, DRIVE TOWATER TANK & FILL WASH TRAILER, DRIVE BACK TO SHOP

2013/09/04 - CLED CORRIGALDRIVE TO BASEMINE LAYDOWN, PRESSURE WASH & CLEAN RDC004, DRIVE TO WATER TANK & FILLTRAILER WITH WATER, DRIVE BACK TO SHOP

2013/09/24-FNAARON CTAKE LUBE TRUCK TO SYNCRUDE BASEMINE LAYDOWN, FILL DIFF AND BOTH FINALS WITH OIL,EVAC WED OIL FROM TUBS, BRING LUBE TRUCK BACK TO SHOP

2013/09/27-ET-28231PIERRE PILOTEREMOVE BACK UP LIGHT FROM THE SIDE OF THE STEP, RE-ROUTE THE HARNESS TO THE BACK,




RE-INSTALL BACK UP LIGHT ON THE BACK OF UNIT, MADE UP HARNESS TO CONNECT TO THE BACKUP LIGHT. MOVE GENERATER ON THE OTHER SIDE OF THE TRAILER

2013/12/13-OTCLAUDE BELISLELOCATE AND FUEL UP HEATESS. LOOK FOR BLOCKING. BROUGHT HAND RAILS TO SHOP FORREPAIRS. HOOK UP HEATERS TO TRUCK CLEANED UP WORK AREA

2013/12/13-OTROD SHEVALIERLOCATE AND MOVE HEATING EQUIPMENT. SET UP DUCTING AND HOOK UP PORTA THAW, UNHOOKAND REFILLED UNITS. RECHECK LOAD DAMAGED CAT WALK AND DELIVER TO SHOP FOR WELDING.CLEAN UP WORK SITE. LOCATE NEW HANDRAILS.

2013/12/14-OTROD SHEVALIERWARM UP UNIT AND GET RUNNING. FILL TIDY TANK AND FUEL TRUCK. PRIME FUEL SYSTEM AND GETRUNNING. TRY TO MOVE TO SHOP, PARK BRAKES NOT RELEASING. LOCATE AND REPAIR AIT LEAKS(NOT BUILDING PRESSURE) START RENTAL, RETURN DEFECTS.

2013/12/14-OTCLAUDE BELISLEWARM UP UNIT AND GOT RUNNING. FILLED TIDY TANK AND FUELED TRUCK UP. PAIRED FUELSYSTEM AND GOT RUNNING, TIRED TO MOVE TO SHOP , PACK BRAKES ARE NTO REBASING, LOCATEAND REPAIR AIR BRAKES (NOT BUBBLING PRESSURE) START RENTAL RETURN OF DEFECTS

2013/12/15-OTROD SHEVALIERINSTALL LEFT SIDE FENDER AND MUD GUARDS. TRY TO GET PARK BRAKES RELEASED. REPAIRHEADLIGHT WIRING, CHASE AIR LEAKS. REPLACE COMPRESSOR GOVERNOR, CHECK AIR LINEROUTING FOR PARK BRAKE CIRCUIT, ADD SAFETY BRAKE TO COMPRESSOR LINE. PARK BRAKESSTILL NOT RELEASEING. TIGHTEN AND REPLACE MISSING BOLTS ON GRILL AND COVERS ON DEFECTLIST. REPAIR R.S BRAKE LIGHT. WIRING ON BOX. REPLACE SHIFTER COXSOL BULB AND CHECK OURLINES

2013/12/15-OTCLAUDE BELISLEINSTALL LEFT SIDE FENDER AND MUD FLAP. TRY TO GET PARK BRAKES RELEASED. REPAIREDHEADLIGHTS AND WIRING, CHASED AIR LEAKS. REPLACED GOVERNOR ON COMPRESSOR, CHECKAIR LINE ROUTINE FOR PARK BRAKE CIRCUIT, ADDED SAFETY BRAKE TO LINES STILL THE PARKBRAKES WILL NOT RELEASE. TIGHTEN AND REPLACED MISSING BOLTS ON GRILL AND GUARDS ONDEFECT LIST. REPAIR RIGHT SIDE BRAKE LIGHT. WIRING ON BOX.

2013/12/16-OTROD SHEVALIERBOOST UNIT AND GET RUNNIN. STRAIGHTEN RIG BOARDING RAILING. TAP MOUNTING BOLT HOLESFOR GRADING ON DRIVERS SIDE (THREADS FULL OF PAINT) REMOVE 2 BROKEN BOLTS, TIGHTENPIPING ON FUEL TANK CROSSOVER, STILL LEAKING TANK WILL HAVE TO BE DRAINED, CONTINUEWORKING ON. PARK BRAKE NOT RELEASING

2013/12/17-ENJOHN HOLLOWAYASSISTED WITH DEFECT REPAIRS. ORDERED PARTS FOR AIR COMPRESSOR GOVERNER AND LINES

2013/12/17-EL-OTTRAVIS GRUNERUDREMOVE COVER OVER BATTERIES IN PROPER POSITION. CLEAN BATTERY CONNECTIONS AND TEST.TOP UP WASHER FLUID AND TEST. ADJUST SEAT SLIDES. ASSISTED WITH LIGHT REPAIRS.INSTALLED MISSING BOLTS. SNOW REMOVAL

2013/12/17-OTAARON CDRILL AND TAP BROKEN BOLTS ON HAND RAILING MOUNT. INSTALL MISSING BOLTS. DRILL ANDTAP BROKEN BOLTS ON PANEL IN FRONT OF CAB INSTALL MISSING BOLTS. TROUBLE SHOOT BRAKELIGHT PROBLEM, REPAIR WIRING ISSUES. REPAIR BACK UP LIGHT CIRCUIT. CHANGE HEAD LIGHTBULBS. SNOW REMOVAL INFRONT OF OFFICE AND PAD

2013/12/16-OTCLAUDE BELISLEBOATED TRUCK TO START IN MORNING TAPED ALL HOLES AROUND FRONT OF DECK HOLES WEREFULL OF PAINT PUT ON DECK AND HAND RAILING, HAD TO REMOVE BROKEN BOLTS. TRIED TOREPAIR FUEL LEAK ON CROSS OVER TIME BUT LEAK WOULDNT STOP TANK WILL HAVE TO BEDRAINED AND REPAIRED.

2013/12/17-OTCLAUDE BELISLEFUELED HOT BOX AND BROUGHT IT TO HEAT WHEELS ON 004, FUELS PORTA THAW AND HOOKED IT




UP TO 004. HOOKED UP BOOSTER CABLES, GOT TRUCK STARTED PUT THAT BOX AND PORTA THAWAWAY. WORKED ON BRAKES TILL WE GOT TRUCK MOVING BROUGHT TRUCK TO GARAGE, MOVEDONE TRUCK OUT OF SHOP AND PUT 004 IN THE SHOP. ADDED MORE TO THE REPAIR LIST

2013/12/17-OTROD SHEVALIERPUT HEAT ON UNIT. BOOST BATTERIES, GET RUNNING. WORK ON PARK BRAKES. BY PASS PARKBRAKE VALVE AND BRING OVER TO SHOP. CONTINUE ON DEFECT LIST

2013/12/18-OTLARRY JACOBSASSIST HOOKING UP LINES, HOSES AND WIRING TO MOBILIZE UNIT

2013/12/18-OTDON GRENIERTIE UP LOOSE ENDS ON CAB INSTALLATION, STARTED UP UNIT. RAISE BOX, FULL OF WATER, SET UPTO TAKE IT OUTSIDE AND DUMP BOX, SHOP DOOR BROKE A CHAIN

31-Dec-2012 WOC171698 - 250HR SERVICE 26,588CARRY OUT 750HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013-02-15 SERVICELEE MEISEDRIVE TO KMC AT SUNCOR, SIGN IN AT KMC OFFICE, CALLED CHANCEY TO HAVE UNITS BROUGHT TO KMC LAYDOWN YARD FOR SERVICES, CHANCEY CAME BY AT 9:30 AM AND CALL AGAIN FOR EMECO'S TRUCK TO BE BROUGHT TO KMC LAYDOWN YARD, FIRST EMECO TRUCK SHOWED UP AT 10:50 AM, DID A 250 HR PM ON RDC004 KMC UNIT NUMBER 4R95, CALL CHANCEY ROUGHLY 20 MINS BEFORE THIS SERVICE WAS DONE TO HAVE ANOTHER EMECO TRUCK BROUGHT TO LAYDOWN, OTHER EMECO TRUCK SHOWED UP AT 1:40 PM, IT WAS NOT ONE OF THE TRUCKS NEEDED TO DO A SERVICE ON ONLY HAD 63 HRS ON OIL FROM IT'S LAST SERVICE DONE FEB 12/13, CALL TO GET A (***) DUE FOR SERVICE, CHANCEY CAME BY AGAIN AND CALLED FOR ANOTHER EMECO TRUC,K TRUCK DID NOT SHOW UP IN TIME, SIGNED OUT AT KMC, DRIVE BACK TO EMECO SHOP, CLEAN OUT LUBE TRUCK AND GET READY FOR THE NEXT DAY

2013-03-20- SERVICELEE MEISE250 HR PM

2013-03-20- SERVICEMELVIN BUTLER250 HR SERVICE, CLEAR UP SITE, CRUSH FILTERS, FILL HYD TANK

18-Dec-2012 WOC172867 - BI-WEEKLY DEC 18 - JAN 01, 13 25,144BI - WEEKLY DEC 19 - JAN 01, As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC13

9-Dec-2012 WOC170969 - FIRE SUPP PM 25,144levitt to do fire supp pm

6-Dec-2012 WOC170452 - B/S TEST 25,124




check b/s terring

DEC 6/12 GREG BRISSEAU

PERFORMED TEST AND FILLED OUTSHEETS

DEC 6/12 MICHAEL SEABORNE

BRAKE AND STEERING TEST, CUT OPEN AND INSPECT FILTERS

6-Dec-2012 WOC170451 - VALVE SETS 25,143set engine valves


ASSIST WITH SET UP


VALVE AND INJECTOR SET


FINISH VALVE AND INJECTOR ADJUSTMENT, REMOVE BENT ROCKER ADJUSTING STUD, ROCKER ASSEMBLY AND DAMAGED VALVE BRIDGE, INPSECT EXHAUST VALVES FOR DAMAGE, INSTALL VALVE COVERS AND NEW GASKETS


HELPED TURN ENGINE TO PIN, CLEANED VALVE COVERS, ORDERED PARTS


REPLACE DAMAGED VALVE COMPONENTS FOR CYL #5, ADJUST VALVE LASH (EXHAUST, INTAKE, INJECTOR,) FOR CYL#5

4-Dec-2012 WOC168360 - REPLACE FRONT TIRES 25,124REPLACE FRONT TIRES

4-Dec-2012 WOC169933 - BI-WEEKLY DEC 05 - DEC 18, 12 25,124




BI- WEEKLY DEC 05 - DEC 18, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2

DEC 5/12 AARON C

RETURN PARTS TO FINNING, PICK UP PARTS @ FINNING

DEC 5/12 MICHAEL BROGAN

RECHARGE FRONT STRUTS, CLEAN ENGINE BREATHERS, CHECK BALL STUDS FOR MOVEMENT, NOMOVEMENT WITH DIAL GUAGE, REMOVE LEFT ROCK EJECTOR AND STRAIGHTEN AND INSTALL,CHECK OVER DEFECT LIST, DETAIL CAB, CLEANED PRIMARY FILTER, FILLED GREASE TANK

DED 5/12 JOHN HOLLOWAY

CHECKED UNIT FOR STATUS OF REPAIRS AND TROUBLESHOOTING


REPLACED TORQUE OUTPUT SEAL, INSTALLED NEW U-JOIN BOLTS

DEC 7/12 AARON C

PICK UP PARTS @FINNING

DEC 7/12 TRAVIS GRUNERUD

REMOVED OLD OVERFLOW LINE ON GREASE KEY, HAD NEW HOSES MADE UP, INSTALLED NEWFITTINGS ON KEY AND NEW LINES


CHANGE ENGINE OIL AND FILTERS AFTER ENGINE WORK, (VALVE SET AND VALVE COMPONENTREPLACEMENT) #5 CYLDINDER, COMPLETE OUT SHEET INSPECTION, REPLACE DAMAGED DECALS,MEASURE RIDE HEIGHTS OR ALL STRUTS TO DETERMINE IF ADJUSTMENT IS NEEDED


REPAIRED BUMPER FIRE EXTINGUISHER MOUNTING, REPLACE EXT & TAG, MEASURED RIDE HEIGHTSON STRUTS, NEED RECHARGING, NO NITROGEN IN STOCK, DID OUT INSPECTION, REPLACED EMECODECALS


GREASER PUMP NOT WORKING CHECK WIRE BROKE GOING INTO PUMP REMOVE PUMP SOLDER WIREBACK ON AND INSTALL, BOLTS BROKE ON HYD CONTROL REMOVE GUARD CLEAN MUD AWAY PUTBACK IN PLACE BOLTS ORDERED

DEC 8/12 AARON C

REPAIR DEFECTS, CHARGE FRONT STRUTS INSTALL COVERS, INSTALL REAR COVERS, ORDER PARTS

DEC 8/12 STEPHEN CHANG

SEE OUTSHEET FOR DETAILS, MADE PARTS ORDER SHEET


REPLACED MOUNTING BOLTS ON HOIST VALVE, REPLACED BREATHER ON ROTOCHAMBER, PAINTEDUNT # ON BUMPER, REPAIRED WIRING AT A/C COMPRESSOR, STARTED TO REMOVE LATERAL LINK

DEC 9/12 JOHN HOLLOWAY

ASSISTED MECHANIC WITH DEFECTS FOUND ON FIELD INSPECTION, REINSPECTED PIN ANDBEARINGS FOR DUMP BODY AND LATERAL LINK


REMOVE LATERAL LINK, PRESS OUT BUSHINGS, INSTALL NEW BUSHINGS, INSTALL LATERAL LINK,EARS ON LEFT SIDE OUTSIDE, SPREAD PUT WASHERS ON INSIDE OF CAP, GREASE LATERAL LINK

DEC 10/12 MOVE MACHINE TO OTHER YARD, CHECK FUEL LEVEL (OUT)


TRUCK ACROSS ROAD IN YARD, HOOKED UP LAPTOP, NO ACTIVE CODES, HOOKED UP PORTA THAW




TO WARM UP, STARTED & BROUGHT TO FUEL UP 100L, PARKED BACK IN YARD

DEC 14/12 - SCOTT MYLES

START UP MACHINE ACROSS YARD, MOVE OUT FOR LOW BED TO ACCESS

DEC 14/12 - FRASER GRIFFON

GO TO OTHER YARD, GET UNIT RUNNING, LET WARM UP, CHECK FOR BRAKES RELEASING, MOVEUNIT FROM LINE UP TO BE LOADED

4-Dec-2012 WOC169722 - WASH UNIT BACK FROM RENTAL 25,124QUOTE # QTM4092

WASH UNIT INSIDE AND OUT BACK FROM RENT

DEC 3/12 ED CORRIGAL

LOCK OUT /TAGOUT AND CHECK WHEELS, POWER WASH AND DEGREASE RDC004, FRONT, TOP SIDES, BACK AND UNDERCARRIAGE, POWERWASH WHEEL HUBS INNER AND OUTER

21-Nov-2012 WOC167045 - BI-WEEKLY NOV 21 - DEC 04, 12 25,071




BI-WEEKLY NOV 21 - DEC 04 - 2As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC012

NOV 24/12 ANTHONY DOUTHWRIGHT

INSTALL PRO HEAT AND BOOST MACHINE TO GET RUNNING, START RENTAL RETURN INSPECTION

NOV 24/12 DANNY HILLIER

GOT PORTA THAW AND BROUGHT OVER TO UNIT, HOOKED UP TO UNIT AND LET RUN TIL BLOCKWAS ABOVE 0 C, AND TRIED TO START BUT BATTERIES DEAD, BOOSTED UNIT AND STARTEDENGINE, STARTED ON IN SHEET INSPECTION

NOV 25/12 JOE A

BOOSTED BATTERY, START ENGINE AND WARM UP MACHINE, FINISHED UP OFF RENTALINSPECTION, CHECK ELECTRICAL, BALL STUDS AND STEERING CYLINDER, CHECK LINE AND FINALDRIVE MAGNETIC PLUG, REMOVED AND CHECK TRANSMISSION SERVICE

NOV 26/12 HARLEY OTTESEN

CHANGING OUT BATTERIES AND STARTING UNIT, TAKEN OIL SAMPLES

NOV 16/12 ANTHONY DOUTHWRIGHT

REPLACE BATTERIES, TAKE OIL SAMPLES FROM ALL COMPONENTS

NOV 27/12 LARRY JACOBS

ASSIST ON INSPECTION

DEC 2/12 RICARTE VALIENTE

BROUGHT HOT BOX TO GET WARM UP, WASH AND CLEAN DIRT OUT OF WASH BAY BEFORE PUTTINGUNIT INSIDE

DEC 3/12 LARRY JACOBS

ASSIST WITH BAR RAISE AND LOWER ELECTRICAL ISSUE

DEC 3/12 ALAN MORTON

BRING MACHINE INTO SHOP, CHECK COOLANT LEAK, FIX HORN, CHANGE OUT R/R/ STRUT GREASEFITTING, ORDER PARTS

DEC 4/12 BRUCE GREENWOOD

MOVE UNIT OUT OF WASH BAY AND DUMP BOX, COLD START HOE TO CLEAN TRAY, MAKE UP JUMPERWIRES FOR SOLENOID CONECTION TO LET TRAY DOWN, CLEAN UP PILE OF DIRT REMOVED FROMTRAY, BRING UNIT INTO SHOP, GO THROUGH LIST AND PULL 500 PM SHEET, REMOVE CUST DECALS

DEC 4/12 BRUCE GREENWOOD

R & R TRAY CYLINDER SOLENOID, GO THROUGH DEFECT AND 500 PM SHEET

DEC 4/12 ALLAN MORTON

DRAIN ENGINE OIL, REMOVE ENG OIL FILTERS, REMOVE FUEL FILTERS, REPLACE ENG OIL, AND FUELFILTERS, FILL ENG OIL, RUN ENG, TOP UP OIL, CHANGE OUT ENG AIR FILTERS (OUTERS) CLEAN PRECLEANERS, CHECK BATTERY CHARGE, CONNECTIONS AND CLEAN TERMINALS, ORDER PARTS(CAB/A/C/FILTERS), CLEAN BAY

6-Nov-2012 WOC163741 - BI-WEEKLY NOV 07 - NOV 20, 12 25,071BI-WEEKLY NOV 07 - NOV 20, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

12-Oct-2012 WOC155409 - 500HRS SERVICE 25,124





ENGINE HOURS:

DATE:






PERFORM 500 HR SERVICE, CHECK LIST, CHANGE FILTERS


REPLACE SEAT BELT, REPLACE THREADED BOSS FOR HOSE CLAMP A REAR DIFF, REPAIR HOSE ANDFOR GREASE LINE REAR STRUT, 500 HRS SERVICE

DEC 6/12 GREG BRIESSEAU

500 HR SERVICE, FINISHED SERVICE CHECKS


500 HRS SERVICE, FINISH SERVICE CHECKLIST, FILTER CHANGES, DRAIN FRONT HUBS ANDINSPECT RH HUB FOR SUSPECTED HYD SEAL LEAK


INSTALLED WINTER FRONT, CLEAN UP BAY

9-Oct-2012 WOC157233 - BI-WEEKLY OCT 10 - OCT 23, 12 25,071BI-WEEKLY OCT 10 - OCT 23, 12

OCT 10/12- DANNY HILLIER'

'DROVE OUT TO UNIT AND INSPECTED CHECKED ALL CONNECTIONS ALL OK TRIED BOOSTING UNIT WITH ANOTHER HAUL TRUCK TILL WON'T START, TRIED CORSSING STARTERS OUT AT SOLENOIDS STILL WON'T TRUN OVER BOTH STARTERS SEEM TO BE DRAWING EXCESSIVE CURRENT NEEDS 2 NEW STARTERS NONE IN STOCK HAVE TO BE ORDERED

OCT 11/12- STEPHEN CHERRY

TRAVEL TO SITE , FLRA, TEST STARTERS, BOTTOM ONE GOOD, SOLENOID ON FRAME BAD , CHANGE TOP STARTER CODES UP, NO STARTER , CODE FOR TRANNY , STEERING CHECK HARNESS FOUND SHORTED OUT WIRE AT NEUTRAL RUN SWITCH , REPAIRED TESTED GOOD FOR NOW, NEED SOLENOID FOR BOTTOM STARTER

OCT 11/12- RYAN ELLIS

TRAVEL TO M/L TO PICK UP PARTS, TRAVEL TO SUNCOR TO GO TO 7930, TURNED AROUND AND WENT TO CARMACKS TO START RDC004, TRAVELED BACK TO SUNCOR TO GIVE STEVE PARTS

OCT 18/12- MARK FORAN

FITTING ON THERMOSTAT HOUSING, DRAINED COOLANT, REMOVED FITTING AND FITTING THREADS ARE BAD, ORDERED FITTING FILLED WITH COOLANT HOSE LEAKING ON STEERING VALVE SMALL LEAK NOT FIXED OPERATOR TOOK TRUCK, REPLACED 2 SOLENOIDS FOR STARTING SYSTEM TORQUE PUT SEAL LEAKING ORDER

OCT 18/12- KIRK GILLIS

DO FRAME INSPECTION, CHECK WINDOWS WASH MOTOR AND WIRING, MOVE TRUCK TO OTHER YARD

25-Sep-2012 WOC154839 - BI-WEEKLY SEPT 26 - OCT 09, 12 25,071




BI-WEEKLY SEPT 26 - OCT 09, 12

SEPT 29/12- ERIC OLSEN'

REPAIR GREASE LINE TO LH STEER CYLINER CHECK DOG BONE BOLT BROKEN DID NOT HAVE ONE INTRUCK

SEPT 30/12- ERIC OLSEN

LOAD AND FUEL TRUCK DRIVE TO UNIT AND REPLACE BOLT AND CALL UNIT UP

OCT 9-12 DANNY HILLIAR

CALLED TO UNIT, HYD LEAK AT HYD HOSE, FOR TRANNY, SEEMS TO BE ORING, REMOVED HOSE,REPLACED ORING AND REINSTALLED, RETESTED OPERATION, ALL OK

11-Sep-2012 WOC152786 - BI-WEEKLY SEPT 13 - SEPT 26,12 24,900BI-WEEKLY SEPT 13 - SEPT 26,12

SEPT 13/12- MARK FORAN

MACHINE DOWN FOR LOW FUEL TWO ORINGS LEAKING ON HOSE REPLACED

29-Aug-2012 WOC150576 - BI-WEEKLY AUG 29 - SEPT 12, 12 24,900BI-WEEKLY AUG 29 - SEPT 12, 12

15-Aug-2012 WOC148686 - BI-WEEKLY AUG 15 - AUG 28, 12 24,846BI-WEEKLY AUG 15 - AUG 28, 12

6-Aug-2012 WOC143524 - 250HR SERVICE 24,419Work not performed under this WOClosed to $0

31-Jul-2012 WOC146690 - BI-WEEKLY AUG 01- AUG 14, 12 24,712BI-WEEKLY AUG 01- AUG 14, 12

AUG 10-12 DANNY HILLIAR

DROVE OUT TO UNIT AND INSPECTED, PULLED WIRES FROM STEERING COLUM AND FOUND HORN CONNECTOR NOT CONNECTED, TENSION WEAK IN TERMINAL, REPLACED TERMINALS AND RECONNECTED, DOESNT COME APART NOW AND HORN WORKING

AUG 11/12- DANNY HILLIER

DROVE OUT TO UNIT AND INSPECTED, FOUND BROKEN TRIPPED FOR LIGHTS RESET ADN APPLIED BRAKES , TRIPPED AGAIN, RAISED BOX PINNED, DISCONNECTED BOX LIGHTS AND RETESTESTED BREAKER DIDN'T TRIP INSPECTED LIGHTS AND WIRING ON BOX FOUND WIRING SHORTED TO BOX AT R/SIDE BRAKE LIGHT, MADE REPAIR ON WIRING BUT WIRING NEEDS TO BE REPLACED ON THAT SIDE , CALLED UNIT UP

17-Jul-2012 WOC144451 - BI-WEEKLY JULY 18 - 31, 2012 24,499BI-WEEKLY JULY 18 - 31, 2012

JULY 19/12- MARK FORAN

REPLACE O-RING ON PUMP TO HOSE, CHECK BOTH FRONT HUBS NE METAL MACHINE WAS NOT RUNNING LITTLE OVER FUEL, CHECKED RR DUAL MAG PLUG PLUS 2 FLATS ON PLUGJULY 31/12- MARK FORAN

CHECK LEFT FINAL FOR METAL ONE FLAKE, OIL SAMPLES FOR BOTH FRONT HUBS, REPLACE TRANS SCREEN AND MAGNETIC

9-Jul-2012 WOC143095 - CHECK F/S SYSTEM 24,419CHECK OVER F/S SYSTEM FOR VOYAGER

4-Jul-2012 WOC142349 - BI WEEKLY WORK ORDER 24,65804/07/12 to 17/07/12

JULY 9/12 - DANNY H

DROVE OUT TO UNIT AND INSPECTED, FOUND ORING LEAKING BETWEEN HOSE AND HOIST PUMP, REMOVED HOSE END AND REPLACED ORING, RETESTED ALL OK

JULY 14/12- DANNY HILLIER

DRAINED FOR FRT HUB OILS AND REFILLED, REPAIRED F/REAR BOX LIGHT OUT




20-Jun-2012 WOC140114 - BI-WEEKLY WORK ORDER 24,419Bi-Weekly Work Order 20-06-12 to 03-07-12

JUNE 22/12- MARK FORAN

FAN NOT WORK ON ANY SPEED, OPERATE SMELT FAN GET HOT THEN SHUT SOWN, PARTS ORDERED

JUNE 23/12- MARK FORAN

REPLACED FAN MOTOR FOR CAB

JUNE 24/12 - MARK F INSPECTED SYSTEM NOT FUNCTIONING, FOUND BAD CONNECTION IN HARNESS, REPAIRED

JUNE 30/12 - STEPHEN C

2000 HR PM, FLRA, START ON INSPECTION, SEE SHEET

JUNE 30/12 - MARK F

2000 HR SERVICE, INSPECTION AND SAMPLES

JUNE 30/12 - DARREN J

SET UP AT UNIT AND STARTED 2000 HR SERVICE, DID ALL RUNNING CHECKS, CLEANED UP AND DROVE BACK TO STOP, UNLOADED TOOLS

JULY 1/12 - MARK F

2000 HR SERVICE, CHANGED ALL OILS AND FILTERS

JULY 1/12 - DARREN J

LOAD PARTS AND TOOLS, DROVE TO VOYAGEUR AND SET UP AT UNIT, COMPLETED 2000 HR SERVICE AND INSPECTION

JULY 2/12 - AARON C

GO THROUGH 6 BOXES OF SAMPLE PAPERWORK TO GO TO FINNINF

19-Jun-2012 WOC139997 - CHECK PARK BRAKE UPDATE 24,296CHECK FOR PROPER VALVE ON PARK BRAKE UPDATE

5-Jun-2012 WOC137883 - BI-WEEKLY JUN 06 - JUN 20, 12 24,296BI-WEEKLY JUN 06 - JUN 20, 12

JUNE 9/12- DANNY HILLIER

DROVE OUT TO UNIT AND INSPECTED FOUND SWITCH TURNED ON FOR SECONDARY STEER, TRIED SYSTEM AND WORKING PROPERLY TURNED OFF SWITCH AND EVERYTHING OK, INSPECTED FOR GREASE LINE AND FOUND CAP MISSING FROM STEER CYLINDER BALL STUD CHECKED PLAY IN STEERING LINKAGES AND ALL OK SOURCED OUT PARTS ON SIS AND ORDERED

JUNE 8/12- DANNY HILLIER

DROVE OUT TO UNIT AND REPLACED 2 HEADLIGHTS BULBS

22-May-2012 WOC135023 - BI-WEEKLY MAY 23 - JUNE 05, 12 24,255BI-WEEKLY MAY 23 - JUNE 05, 12

MAY 25/12 MARK FORAN

INSTALLED LINE ON MACHINE AND CALLED FOR OIL FOR MACHINE

MAY 24/12- MARK FORAN

CALL FROM CARMACKS AND HEADED TO VOYAGEUR, REMOVED LINE AND HEADED TO FINNING TO GET HOME MADE, HOSE IS MADE

8-May-2012 WOC133765 - BI-WEEKLY MAY 09 - MAY 22, 12 24,243




BI-WEEKLY MAY 09 - MAY 22, 12

MAY 23/12- JIM MACFARLANE

TRAVEL TO FINNING HOSE NOT MADE WAITED FOR HOSE TO BE MADE, TRAVEL TO VOYAGEAR,INSTALLED HOSE, CALLED FOR OIL FILLED WITH OIL STARTED UNIT . ANOTHER HOSE LEAKING.TORQUE SUPPLY ORDERD HOSE TRAVELED TO FINNING WAITED FOR PARTS RETURNED TO MACHINEINSTALLED HOSE TESTED OK, RETURN TO SHOP CLEAN UP AFTER SHIFT

3-May-2012 WOC133305 - BRAKE STERRING TEST 24,242CHECK SYSTEM OUT

24-Apr-2012 WOC132266 - BI-WEEKLY APR 25 - MAY 08, 12 24,222BI-WEEKLY APR 25 - MAY 08, 12

MAY.2.2012-MICHEAL L WELD SIDE BOARDS ON MACHINE

MAY.2.2012-MICHEAL L NEED SIDE BOARRDS, WELD SIDE BOARDS ON MACHINE

MAY 5.2012-TRANS G REPAIR DEFECTS, BUILD PLATE FOR SUPPORT BRACKET ON FENDER, REMOVE STEPS AND STRAIGHTEN,BUILD SUPPORT BRACKETS

APR 26/12-MICHAEL BROGAN

ASSEMBLE TRANSMISSION PUMP, INSTALL HOSES TO PUMP

APR 26/12- TRAVIS G

REMOVE FUEL LINE CLEAN AROUND CONNECTIONS INSTALL NEW FUEL LINE HELP INSTALL TRANNY SCARENGE PUMP

APR 26/12-MELVIN BUTLER

PARTS RUN TO FINNING FOR HOSES FOR 777, RETURN TO FINIING WITH WRONG HOSES AND GET PROPER HOSE, ALSO PLU SEALS FOR 777

22-Apr-2012 WOC132053 - 1200 HOUR FIRE SUPPRESSION PM 24,255carry out 1200 hour fire suppression service

10-Apr-2012 WOC131061 - BI-WEEKLY APR 11 - APR 24, 12 24,222BI-WEEKLY APR 11 - APR 24, 12APR.13.2012-DAN H CHECK R/F HUB, IS A BIT OVERFULL.GET OIL CHANGED OUT.WELL RUN TRUC K FOR SHIFT AND CHECK AGAIN.CANT WITH DEFECT LIST.LOOK UP AND ORDER PARTS.FIX WIRING FOR REAR BOX LIGHT

APR.17.2012-DAN H TRUCK WAS BEING MOVED OFF SITE, SEPERATORS COMPLAINT OF ALARMS IN CAB AND P/B LIGHT ON.GET RIDE TO UNIT WITH LABOURER.SAFETY TRUCK AND CHECK FINAL WIRES FOR BRAKE OVERSTROKE ARE BROKEN OFF.STRIP WIRES AND TWIST TOGETHER SEND TRUCK ON IT WAY GET RIDE BACK TO SERVIC E TRUCK

APR.22.2012- INSTALLED AXLES AND FINAL DRIVE COVERS, FILLED TRANSMISSION AND DIFFERENTIAL OILS, CHECKED STEERING SYSTEM FOR PLAY, LOOKED INTO DEFECTS LIGHT AND ORDERED REQUIREDX PARTS FOR REPAIRS, SHIMMED BOX PINS TIGHT,CLEANED UP AREA AND FOOLING.

APR.23.2012-STEPHEN B MOVEMENT IN STEERING BALL-JOINTS, CONVERTER SEAL LEAKING, REMOVED STEERING RAM, REPLACED BALL JOINTS, REPLACED O RINGS, INSTALLED CYLINDER,REMOVED DRIVE SHAFT, REMOVED CONVERTER SEAL RETAINER,INCORRECT SEAL WAS ORDERED ( WAITING ON PARTS) ORDERED PART, CLEANED WORK AREA

APR.23.2012-LUCAS A REPLACED RHS STEERING CYLINDER BALL STUDS,REPLACED COOLANT LEVEL INDICATORS AND GSKETS,HELPECD STEPHEN WITH TORQUE OUTPUT SHAFT SEAL REPLACEMENT,NEW SEAL IS TOO BIG,ORDERED PROPER SEAL,WILLARRIVE TOMORROW

29-Mar-2012 WOC129243 - BI-WEEKLY MAR 28, - APR 10, 12 24,222BI-WEEKLY MAR 28, - APR 10, 12

14-Mar-2012 WOC126542 - BI-WEEKLY MAR 14 - MAR 27, 12 24,114




BI-WEEKLY MAR 14 - MAR 27, 12

MAR 14, 2012 - DAN HEINECHECK ON PARTS FOR GREASE INJ. NOT IN YET. TIE UP GREASE INJ SET UP SO TRUCK CAN RUN.START CHECKING FUEL DILUTION COMPLAINTS. CUSTOMERS OIL SAMPLE WERE OLF. BEFORE LASTREPAIR. TRY TO GET MORE RECENT SAMPLE. CHECK OIL LEVEL. TRY TO START. BOOST TRUCK.NEED BIT MORE INFO ON SAMPLE AND HIS.

MAR 16, 2012 - DON PSTART UNITDROVE TO SITE. CHECKED FLUIDS. STARTED UNIT. CHECKED FOR LEAKS. CALLED UP. INSTALLSAT RADIO. PULLED REAR CAB PANEL. ROUTED ANTENNA THROUGH INTO CAB. SECURED ANTENNAWIRE. DROVE BACK TO SHOP.

8-Mar-2012 WOC125564 - GREASE SYS DAMAGE 24,124MACHINE AT LEDCOR SUNCOR BACKED INTO DIRT AND DAMAGED IJECTORS

MAR 15, 2012 - DAN HEINEPULL OFF GREASE BLOCK. REMOVE BROKEN FITTINGS. INSTALL TWO NEW INJECTORS ON MIDDLE SECTION AND UT NEW 4 PIECE BLOCK ON KLEFT SIDE MOUNT BRACKETS. HOOK UP HOSES MISSING 90 DEGREE ELBOWS FOR NEW SECTION. ORDERED PARTS.

MAR 16,2012- DAN HINSTALL ELBOWS AND GREASE LINES. RUN GREASE SYSTEM. ALL OK

7-Mar-2012 CME132 - CHANGE OUT DIFFERENTIAL 23,849OVER HOURED COMPONENT CHANGE OUT - BEFORE FAILURE

CHANGE OUT DIFFERENTIAL WITH FINNING EXCHANGE

APR.21.2012-DEAN FDIFF NEEDS TO CHANGE OUT REPLACE DIF, WASH UNIT, DRAIN WHEEL GROUPS AND DIFF,SSET UP RIGGING AND CRANE, REMOVE NECESARY COMPONENTS,REMOVE DIFF

APR.21.2012-STAN S INSTALL AND TORQUE DRIVE SHAFT, INSTALL LINE, WIRES AND SHIELDS

APR.21.2012-LUCAS A HELPED STEPHEN REMOVE AND INSTALL TRANSMISSION AND DIFFERENTIAL FOR DIFFERENTIAL REPLACEMENT

APR.21.2012-STEPHEN B MOVED MACHINE FROM ACROSS THE ROAD,WASHED TRANNY AND DIFF AREA, DRAINED DIFF AND FINAL DRIVES,REMOVED LINES AND DRIVE SHAFT,REMOVED TRANNY AND DIFF,MOVED INTO SHOP REMOVED DIFF INSTALLED NEW, INSTALLED NEW DIFF,CLEANED WORK AREA AND SHOP.

APR.22.2012-STEPHEN B FINISHED INSTALLEING TRANS AND DIFF,FITTED AXLE,FILLED DIFF AND TRANS, CHECKED MACHINE OVER, MADE PARTS LIST AND JOB SHEET, ORDERED PARRTST CHECKED GREASE SYSTEM STRUS OVER GREAASING ADJUSTED INJECTORS,CHECKED STEERING SYSTEM,REMOVED CAPS READY TO BE WASHED,SHIMED TUB PINS REAR.CLEANED WORK AREA,

27-Feb-2012 WOC123780 - BI-WEEKLY FEB 29 - MAR 13, 12 24,113BI-WEEKLY FEB 29 - MAR 13, 12

MAR 8, 2012 - MARK FFUEL IN OILLEFT SHOP HEADED TO SUNCOR. REMOVED INJECTOR COVERS, TO INSPECT FOR FUEL LEAKS, PRIMED SYSTEM AND NO LEAKS WERE VISABLE. ALSO STARTED AND INSPECT NO LEAKS. OIL SAMPLE TAKEN ABOUT 300 HRS AGO, LEDCOR CHANGED OIL AND WILL RESAMPLE IN 50 HR.

MAR 11, 2012-MARK FOIL SAMPLEOIL SAMPLE FROM ENGINE TO TEST FOR FUEL BUT ENGINE OIL WAS CHANGED BY MISTAKE LAST NIGHT. FRONT STRUT LOW. PUMPS LOAKING BUT WILL NEED TO BE CLEANED. INSPECTED MACHINE.

14-Feb-2012 WOC122253 - BI-WEEKLY FEB 15 - FEB 22, 12 23,802




BI-WEEKLY FEB 15 - FEB 22, 12

FEB 20, 2012 - DAN HEINELOW POWER, SHIFTING COMPLAINTCHECK TRANS SCREEN, CHECK TRANS PRESSURE. ALL OK. CHARGE R/F STRUT LOWER L/F. STARTAND WARM UP. GO FOR TWO LOADS. SHIFTING PROBLEM IS DUE TO LOW POWER. L/H EXHAUSTTEMP A LITTLE LOW. BRING BACK TO LAYDOWN. DO CYL CUT OUT. #2 IS NOT WORKING. PULL #2INJECTOR, FIND EXHAUST BRIDGE BROKEN AT DOWEL SLOT, AND THREE OF THE SOLENOID HOLDDOWN BOLTS ARE SHEARED OFF.

FEB 21, 2012 - DAN HEINELOW POWER, SHIFTING PROBLEMSGOT TO FINNING TO PICK UP PARTS (INJ). APPARENTLY THERE WAS BO STOCK WHEN THEY WENTTO PAICK PARTS. DRIVE BACK TO SHOP. PULL INJ OUT OF OLD ENGINE IN TENT. TRAVEL TO SITE.INSTALL INJ IN UNIT. PIN ENGINE AND CHECK/ADJUST VALVED AND INJ HEIGHT FOR #2. CHECKOTHER VALVE AND INJECTORS. ALL WITHIN SPEC. START AND WARM UNIT. DO CYL CUT OUT, #2IS WORKING NOW, CALL UP AND SEND TO WORK.

1-Feb-2012 WOC120385 - BI-WEEKLY FEB 02 - FEB 14, 12 22,754BI-WEEKLY FEB 02 - FEB 14, 12

FEB 12, 2012 - JIM MACFARLANEENGINE RAISESTICKING VALVESCHECKED MACHINE AND FOUNF THE VALV STICKING WHEN COLD. CUT AND INSPECTED ENGINE OIL FILTER. REMOVED CALVE COVERS AND INSPECTED VALVE TRAIN, ALL IN PLACE. STARTED UNIT AND WARMED UP OK. MACHINE IS IDELING ALOT AND HAD CARBON BUILD UP CAUSING THE VALVE TO STICK WHEN COLD. INSTRUCTED ART TO TELL THE OPERATORS TO LET THE ENGINES IDLE UP TO STAY WARM AND NOT USE THE TRANS LOCK WHEN THE MACHINE ARE PARKED. THIS CAUSES THE MACHINE TO IDLE. UNIT IS STILL DOWN BECAUSE CUSTOMER ROBBED A HOSE FROM ANOTHER UNIT.

26-Jan-2012 WOC119208 - INSTALL HUNGRY BOARDS 22,754Install Hungry BoardsWork carried out on site at LedcorFabricated by Mckenzie WeldingInstalled by SMS

8-Dec-2011 WOC111004 - LOW POWER 22,701TROUBLESHOOT LOW POWER

DEC 8, 2011 - TROUBLESHOOT LOW POWER

DEC 8, 2011 - MARK FWHEN ARRIVING AT SITE SIPERVISOR INFORMED ME TRUCK HAD ENGINE TROUBLE. WENT TO TRUCK CHECK FLUID LEVELS AND INSPECT ENGINE. HOOK COMPUTER UP TO MACHINE NO CODES OF ANY TROUBLE. STARTED TRUCK LET WARM FOR HALF AN HOUR STILL NO CODES. INFORMED LEDCOR SUPERVISOR AND CALLED UP 10:00. OPERATOR ARRIVED WENT FOR DRIVE AND CHECKED PRESSURES AND PERFORMED A CUT OUT TEST ON INJECTORS O.K. MACHINE WORKED AND NO CALLS.

27-Oct-2011 WOC105492 - REPAIR GREASE SYSTEM 21,832Install grease system module that is missing

OCT 27, 2011 - REPAIR GREASE SYSTEM

OCT 28, 2011 - DAN HEINECUT PLATE FOR MODULE. DRILL OUT HOLES AND MOUNT MODULE. INSTALL MODULE IN CAB. HOOK UP HARNESS. FOX WORING BY GREASE PUMP. GET UNIT RUNNING AND CYCLE SYSTEM UNTIL ALL POINTS ARE GETTING GREASE. CLEAN UP WORK AREA, WAIT FOR ESCORT OFF SITE.

OCT 27, 2011 - DAN HEINEPICK THROUGH PART ROOMS AND FIND RIGHT PARTS. FIND MOUNTING STEEL.

OCT 26, 2011 - DAN HEINEDRIVE TO SITE WAIT FOR ESCORT, SIGN IN AND WAIT FOR TRUCK TO SHOW UP. CHECK GREASE SYSTEM, FIND CENTRAL MODULE IN CAB MISSING. CALL OFFICE TO CHECK PART. PARK UNIT OUT OF WAY, WAIT FOR ESCORT OUT.

16-Oct-2011 WOC103957 - CHANGE BELTS AND PULLEY 21,727




change belts and pulley

OCT 16, 2011 - CHANGE BELTS AND PULLEY

OCT 16, 2011 - KEVIN LDRIVE TO MACHINE FILLED OUT FLRA, LOCKED AND TAGGED UNIT OUT OF SERVICE. CHECK FORCAUSE OF FAN BELTS COMING OFF, FOUND FAN BELT TENSIONER PULLEY BEARING FAILED ANDGROOVED IN CRANK CHAFT BELT PULLEY WORN TOO DEEP. ORDERED TENSIONER PULLEY ANDCRANK SHAFT PULLEY AND BELTS ON SUNDAY OCT 16, 2011. CALLED GEORGE AND GAVE HIM PART#'S.

OCT 19, 2011 - MARK FORANLEFT SHOP HEADED TO FINNING TO PICK P PARTS. WAITED AND HOUR FOR PARTS. LEFT FINNINGHEAD TO JACKPINE CALLED FOR ESCORT AND WAITED FOR 45 MINS. STARTED TO INSPECT ANDREMOVE STUMP PANS AND TENSIONER ROLLER AND NOTICED THAT TENSIONER WAS FALLING OFF.BOLT CAME OUT TO HOLD TENSIONER TOGETHER. INSTALLED NEW WASHER AND BOLT. INSTALLEDBELTS ON TRUCK STARTED AND INSPECTED.

14-Oct-2011 WOC103780 - REPAIR DEFECTS 21,727repair hornreplace both left and right side mirrorsreplace dipstickcharge strutsrepair lightsadjust door latch

OCT 14, 2011 - LEE MREPAIRSLOOK AT THE CONDITION OF REARVIEW MIRRORS. SCRATCH WILL NEED TO BE REPLACED. MIRRORS ARE ORDERED. REPLACED HORD FOR THE MEAN TIME, PARTS ARE ON ORDER.

OCT 18, 2011 - MARK FORANINSTALLED MIRROR ON R/H SIDE OF TRUCK. REPLACED DIPSTICK. TRIED TO REPAIR HORN BUT NEED MORE TOOLS. ALSO NEED MORE PARTS

OCT 19, 2011 - MARK FORANREPLACED MIRROR ON L/H SIDE. REPLACED BRUSH KIT FOR HORN. CHARGE STRUT ON RH SIDE STRUT WAS AT 6" CHARGED UP TO 9"

23-Sep-2011 WOC100920 - WINTER PACKAGE 21,578Wards to install winter package

SEPT 22, 2011 - WINTER PACKAGE (WARDS) GUARD (MADE NEEDS INSTALLED)

SEPT 22, 2011 - BUILD GUARD FOR HYD TANK. HEAT AND INSTALL. WINTER PACKAGE INSTALLED. - MIKE LEE

21-Sep-2011 WOC100772 - FIRE SUPP PM 21,599FIRE SUPP PM

SEPT 21, 11 - LEVITTEINSPECTION OF FIRE SUPPRESSION SYSTEM. CHECKED ALL HOSES, NOZZLES, FITTINGS. CHECKED ACTUATION HEADS AND METRONS, METERED PANEL. CHECKED/TESTED PULL STATIONS. TESTED SHOTS, TESTED ENGINE SHUTDOWN, TESTED DAF'S. CHECKED WIRING, MADE REPAIRS TO BATTERY WIRE AND DETECTION WIRING. SYSTEM OK.

20-Sep-2011 WOC100689 - INSTALL GPS OIL SWITCH AND 21,578install oil pressure switch

SEPT 21, 11 - DONHAD TO FIND GPS UNIT, LOCATED PARK BRAKE SWITCH. INSTALLED ENGINE OIL PRESSURE SWITCH.

RAN WIRES TO OIL PRESSURE SWITCH, TESTED GPS.

2-Sep-2011 WOC00850 - REAPIR START ISSUE 21,598found broken wire by conection

SEPT 01, 11 - DALE BTRUCK WOULD NOT START, FOUND STARTER CABLE BROKEN. REPLACED CABLE WITH NEW.

SEPT 11, 11 - DALE BTRY TO BOOST TRUCK TO START. BOTTOM STARTER DOES NOT HAVE GROUND STRAP, HAS BEEN STARTING ON ONE STARTER ONLY. INSTALLED GROUND STRAP. REPAIRED INTERMITTANT HORN BUTTON WIRE, LOOSE CONNECTION. INSTALLED NEW CONNECTOR.




31-Aug-2011 WOC00832 - REPLACE DECALS 21,598REPLACE CAT DECALS

SEPT 02, 11 - DALE BREPLACED CAT DECALS ON FRONT FENDERS. TOUCH UP PAINT, INSTALLED SIGNAL LIGHTS.

SEPT 02, 11 - GLADIATOR, TOMREMOVE DECALS, HEAT UP, REMOVE. DIG MUD OUT FROM BACK SIDE OF LIGHTS. UNBOLT FROM FENDER. MOVE TRUCK OUT OF SHOP, DUMP WATER OUT OF BOX.

NOT DATED - DALE BINSTALLED LAST DECAL. PICKED UP TONIGHT FROM FINNING.

31-Aug-2011 WOC00833 - REPAIR BOX 21,598REPAIR DAMAGE AT LEFT REAR CORNER OF BOX.

SEPT 02, 11 - TOM BCUT OUT AREA AROUND DAMAGE. CLEAN UP AREA. BRING STEEL IN TO MAKE PLATES.

SEPT 03, 11 - TOM BMAKE PATCHES FOR HOLES THAT WERE CUT OUT. WELD IN PATCHES.

SEPT 23, 11 - IRON SMITHGOUGE OLD PLATE OFF ONE SIDE OF BOX LINER AT BACK OF BOX.

SEPT 24, 11 - IRON SMITHGOUGED OUT OLD LINER PLATE. CLEANED UP WITH GRINDER AND PREPED FOR NEW PLATE. LAID OUT NEW PLATE, STARTED CUTTING PLATE.

SEPT 25, 11 - IRON SMITHCUT PLATE FOR LINER. GRIND CLEAN CUT, PLUG WELD HOLES. FIT AND TACKED BOTH LINER PLATES INTO PLACE. WELDED OUT ONE PLATE. STARTED WELDING OTHER ONE.

SEPT 26, 11 - IRON SMITHFINISH WELDING LINER PLATE. GRIND ALL DOG AND WEDGE WELDS OFF FLUSH.

SEPT 26 ,11 IRON SMITH

REPLACE 2 BACK DOVE TAILS IN BOX

14-Aug-2011 WOC00593 - LEFT TRACTION SENSOR CHANGE OU 21,596Remove left side traction control sensor. Old one damaged and not working properly because it is locking the left final drive up when traveling forward or backwards

AUG 14, 11 - KEITH O'NEILATTEMPTED TO PARK UNIT IN BACK OF YARD, WHILE DRIVING NOTICED BRAKES ACTIVATING OCCASIONALLY ON REAR. CONNECTED LAP TOP, CHECKED SENSOR SPEEDS, NOTICED LHR NOT CONSISTANT AND ACTIVATING TRACTION CONTROL REMOVED GUARD, REMOVED SENSOR, HAD DIFFICULTY REMOVING (BENT AND BROKEN). ROBBED PART FROM RDC003 AND INSTALLED. TESTED, NO OK. NOTICED ORING ON LH PARK BRAKE BLEED SCREW LEAKING. CHANGED AND CLEANED BRAKE AND RIM.

3-Aug-2011 WOC00426 - OUT SHEET 21,596




check machine over after KevinL did out sheet and failed

AUG 01, 11 - DEFECTS - AARONBRAKE COOLING HOSE LEAKING FRONT RIGHT OF ENGINE. MARKED WITH RED TAPE. FUEL TANKLEAKING AT FAST FILL. EMERGENCY STEERING VALVE LEAKING, WILL NEED TO CLEAN AND RUN TODETERMINE WHERE OIL IS COMING FROM. LOW BEAM LIGHT OUT. RIGHT REAR FINAL DRIVE DRAINPLUG LEAKING. MISSING WASHER NOZZLE. NEED DOOR STRIKER, DOOR RATTLES, SOME ONE PUTELECTRICAL TAPE ON IT TO SHIM IT UP. MISSING CIG LIGHTER. HEATER VENT MISSING, BROKENABOVE FOOT PEDAL. RIGHT REAR RED LIGHT ON BOX NEEDS REPLACED.

AUG 05, 11 - REPAIR DEFECTS FROM OUT LIST - RENECHECK FOR THE REPAIRS. REPAIR LEFT FRONT LOW BEAM WIRING. START REPAIRING R/R BOXLIGHT WIRING.

AUG 06, 11 - REPAIR DEFECTS - RENEREPAIR (REWIRE) BOTH REAR BOX LIGHTS, R & L. REPLACE DOOR STRIKER. REPLACE LOWER HEATLOUVERS. CLEAN OUT AIR PRE-CLEANERS.

AUG 07, 11 - REPAIR DEFECTS - RENEREPLACE TORQUE OUTPUT SEAL, WASH OFF LEAKAGE, RUN AND CHECK REPAIR, OK. REPAIRLEAKING FITTING AT BRAKE VALVE, REPLACE ORINGS IN FITTING. WAS LEFT LEAKING. RUN ANDCHECK REAPIR, OK. REPAIR LEAK AT EMERGENCY STEERING VALVE. TIGHTEN RELIEF VALVEFITTING. SCRAP OFF BUILT UP LEAKAGE/SLUDGE. CLEAN COVER, WASH OFF LEAKAGE, RUN ANDCHECK REPAIR, OK. WASH OFF LEAKAGE AT FRONT RIGHT BRAKE COOLER HOSE. RUN AND VERIFYLEAK. HOSE IS ORDERED. REMOVED RIGHT REAR FINAL DRIVE DRAIN PLUG, CLEAN GASKET ANDREINSTALL. WASH OFF LEAKAGE. WASH OFF LEAKAGE AT FAST FILL FUEL AND RECHECK FOR LEAK,OK.

AUG 08, 11 - RENEREPAIRED REAR BOX MARKER LIGHTS WIRING. REWIRED, WAS ALL BUTT CONNECTORS ANDBROKEN WIRES. REPLACED AND ADJUSTED DOOR STRIKER POSTS. BOTH SIDES. REPLACEDLOWER DUCT LOUVER FOR CAB. CLEANED OUT AIR FILTER PRE-CLEANER. REPLACED TORQUEOUTPUT SEAL. REPAIRED HYDRAULIC LEAKS, BRAKE VALVE AND LEAKS AT EMERGENCY STEERINGVALVE. WASH OFF AND VERIFY REPAIR. WASH OFF LEAKAGE AT RF BRAKE COOLER HOSE UNDERENGINE AND VERIFY LEAK. HOSE WAS ORDERED AWHILE AGO. WASH OFF LEAKAGE AT FAST FILLVALVE, VERIFY LEAK. NOT LEAKING.

AUG 12, 11 - REPLACED COOLER LINE - RICARTEHELP DALE TO DO OUTSHEET, FOUND DEFECTS THAT NEED ATTENTION. MODIFY AUTO-LUBE SPILLHOSE LINE. INSTALLED WINDSHIELD SQUIRTER NOZZLE. REPLACED COOLER LINE AND MODIFIEDBRACKET TO KEEP HOSE AWAY FROM RUBBING OFF THE COOLER BODY AND TOPPED UP HYDRAULICOIL AND FILLED WASHER FLUID RESEVOIR. TOPPED UP ENGINE OIL AND COOLANT. ALSOREPAIRED BACK UP LIGHT. FILLED UP GREASE.

SEPT 03, 11 - DALE BOUTSHEET INSPECTION, MOVE TO DIVERSIFIED YARD.

SEPT 29, 11 - ROGERMOVE TRUCK AND CHECK ALL FLUIDS. TOPPED UP AS NEEDED. ALL FLUIDS GOOD.

6-May-2011 WOC94509 - REPLACE FUEL WIGGINS FITTING 21,596WIGGINS FITTING LEAKING

MAY 08, 11 - FUEL TANK WIGGINS FITTING - ROD MR&R WIGGINS FITTING ON FUEL TANK. MOVE UNIT TO NEW YARD. T/S STEERING/PARK BRAKE ISSUE FOUND LOOSE CONNECTION ON TRANS LOCK OUT. REPAIRED AND GOOD NOW.

19-Apr-2011 WOC92405 - REPAIR FIRE SUPPRESION 21,595REPAIR FIRE SUPPRESION GOING OFF

APR 19, 11 - RECHARGE - LEVITTDISMOUNTED TANKS ANDBLEW OUT LINES, REPALCED CAPS. VISUALLY INSPECTED SYSTEM. ACTUATOR HAEDS AND DISCHARGE ADAPTORS PUT INSIDE OPERATORS CAB. REPLACE METRONS. RECHARGE ONGOING (NOT COMPLETED)

APR 20, 11 - RECHARGE - LEVITTLIFT TANKS ONTO TRUCK. SERCURE TANKS ONTO SKID. RE-ASSEMBLE TANK HEADS, DO A SYSTEM FUNCTION TEST(PULL STATION, DETECTION, SHOT AND ENGINE SHUT DOWN) RE-ARM SYSTEM OK.

5-Apr-2011 WOC90105 - 2000 HR PM 21,590




MACHINE PARKED AT KMC YARD, KMC DOESNT DO HYD OR DIFF'S ON THE 2000 SO OUR 2000HR ISBEEN DONE TO START FRESH

ARP 6, 11 - 2000 HR SERVICES - KEVIN/LEEGATHER UP KIT, HAD A BIT OF A WAIT DUE TO PARTS GUY HAD TO DO THEIR PAPEROWRK BEFORERELEASING PARTS. HAD TO LOOK THROUGH SEA CONS FOR AIR FILTERS. DRIVE TO UNIT, FILLEDOUT FLRA, LOCKED AND CHOCKED UNIT OUT OF SERVICE. HAD TO WORK AROUND FIRESUPRESSION GUYS, MADE A JOB A LITTLE BIT SLOWER. DRAINED TRANS TANK, TOOK OIL SMAPLEFROM TRANSMISSION. DRAINED TRANSMISSION CANNISTER, WAS DIRT IN BOTTOM OF CANNISTER,CLEANED CANNISTER. REPLACED FILTERS, CLEANED OUT TRANSMISSION SCREEN, MAGNET WASCLEAN, VERY LITTLE FILINGS. CHANGED OUT OIL FILTERS, CLEANED WATER SEPERATOR, WASSMALL AMOUNT OF FIRT IN CANNISTER, REPLACED FUEL FILTERS, PRIMED FUEL SYSTEM, DRAINEDENGINE OIL, TOOK OIL SAMPLE, REFILLED WITH OW 40 OIL. CHANGED FUEL TANK AND HYD TANKBREATHER, CHANGED STEERING FILTERS 1 OF FILTERS WAS MISSING FROM KIT. ONLY CHANGED 1OF THE STEERING FILTERS. DRAINED AND TOOK SOS SAMPLE STEERING OIL.INSTALLED NEW INNER AND OUTER ENGINE AIR FILTERS, REPLACED INNER AND OUTER CAB AIRFILTERS, ALL CAPS AND DRAIN PLUGS CLEANED OFF AND DOUBLE CHECKED FOR TIGHTNESS.FOUND DIFF OVERFILL BY ABOUT 40-50 L, BROUGHT DOWN TO PROPER LEVEL. STARTED TODIAGNOSE FOR LEAKING DUO CONE. RAN UNIT FOR APROX 45 MINS WITH PARK BRAKE. RELEASEDAND APPLIED, NO SIGNIFICANT CHANGE IN DIFF OIL LEVEL. DRAINED AND FILLED DIFF WITH 50WOIL

5-Apr-2011 WOC90062 - 1200HR F/S INSPECTION 21,5901200HR FIRE SUPPRESSION INSPECTION

APR 06, 11 - 1200HR P17CM 777 - LEVITTEREPALCED METRON FIXED SHOT WIRE, TESTED PANEL, TESTED SHOTREPLACED BLOW OFF CAPS, TIGHTENED ALL FITTINGS, CHECK PORTABLE EXT. CHECKED TANK PRESSURE AND CANDISSIENT DATE FLAME TEST DAF'S INSPECTED HOSES

29-Mar-2011 WOC88980 - CHANGE FRONT TIRES 21,591Tires have reached 4000 hr interval

FORMS ON FILENO OTHER INFO

28-Mar-2011 WOC88917 - VALVE SET 21,578fill out sheet

27-Mar-2011 WOC88977 - VALVE SET 21,588complete form and submit

MAR 28, 11 - JIM MPERFORED FIRST VALVE SET. CHECKED ALL SETINGS. DID NOT CHANGE ANY SETTINGS, TORQUED ROCKERF AN NUTS TO 52 FT/LBS. TORQUED INSPECTED FANNUTS TO 82 FT/BS.

26-Mar-2011 WOC88811 - CHANGE TORQUE CONVERTER 21,588- Bolts holding torque together are either broken or missingChange torque pump.

MAR 26, 11 - DEFECTS - JIM MTRAVELED TO UNIT. STARTED AND WARMED. RAISED BODY AND SECURED. REMOVED ACCESSARY DRIVE GUARDS. REMOVED DRIVE SHAFT AND YOKE. REMOVED SEAL. CLEANED AREA, INSTALLED A NEW LIP SEAL. CLEANED UP YOKE AND REINSTALLED. INSTALLED NEW SHFT AND GUARDS. RAN UNIT OK. DRAINED HYDRAULIC TANK. REMOVED LINES FROM TORQUE PUMP. REMOVED PUMP, FOUND THAT THERE WERE BROKEN BOLTS IN THE CASE AND ALL THE BOLTS THAT HELD THE TORQUE TOGETHER WERE LOOSE. REMOVED THE TORQUE FROM THE TRUCK. REPAIRED OIL LEAKS AT THE HOIST VALVE LINES. CHARGES REAR SUSPENSIONS TO START. REMOVE THE DIFF TAG LINK. CLEANED UP AORK AREA, COVERED LINES AND COMPARTMENTS, ORDERED PARTS

APR 2, 11 - R&R TORQUE - DARREN/MARKLOADED PARTS INTO TRUCK, DROVE TO MILDRED LAKE SET UP AT TRUCK AND WAITED FOR MARK TO SHOW UP AND LIFTED TORQUE ONTO PLACE, AND INSTALLED. INSTALLED HOSES ND SWAPPED PARTS ON TO NEW TORQUE SAVENGE PUMP AND INSTALLED REPLACED O-RINGS ON HOSES. CLEANED UP AND DROVE BACK TO THE SHOP. ORDERED PLUGS MISSING FROM TORQUE.

APR 3, 11 - INSTALL TORQUE - DARREN/MARKDROVE TO UNIT AND SET UP. FINISHED INSTALLED ALL PARTS RELATED TO THE REMOVAL OF THE TORQUE. MARK BROUGHT THE LUBE TRUCK AND WE FILLED ALL THE OILS AND CLEANED UP THE GARBAGE AROUND THE TRUCK. RAN THE TRUCK AND LET THE BOX DOWN. PREPED FOR DOG BONE REMOVAL. DRVOE BACK TO THE SHOP.

21-Mar-2011 WOC88211 - DEFECT LIST REPAIRS 21,592




Check list - list defects on service report

MAR 21, 11 - DEFECT LIST - DANLOOK UP AND ORDER PARTS FOR DEFECT LIST

MAR 25, 11 - DEFECTS LIST - JIM MSEARCHED FOR PARTS, CHECKED OVER REPAIR LIST-TRAVEL TO UNIT. START AND WARM UNIT.MOVED MACHINE. RAISED BODY AND FOUND THAT THERE WAS ABOUT 30 TONS OF MUD FROZENFROKEN IN THE BOSY. LOWERED BODY. CALL TO HAVE THE BODY SCRAPED OUTREPLACED MASTER SWITCH, REMOVED BROKEN GREASE LINE FITTING AND INSTALLED NEWFITTINGS. REPAIR CAB AIR FILTER DOOR. SCRAPED KMC DECALS OFF. CLEANED HOIST VALVE ANDTORQUE PUMP TO FIX OIL LEAKSKMC CAME CAN TOOK MACHINE TO CLEAN OUT BODYMAR 27, 11 - JIM MLOADED JACK, STANDS, PUMPS AND PARTS INTO TRUCK. TRAVELED TO UNIT, JACKED UP TRUCK.REMOVED LEFT FRONT WHEEL REMOVED BEARINGS AND HUB. FOUND BEARINGS TO BE FAILING.CLEANED ALL PARTS. LOADED PARTS INTO EMECO TRUCK AND SENT THEM TO THE SHOP. ORDEREDPARTS

MAR 28, 11 - JIM MWELDED OUT BEARINGS CUPS. CLEANED HUB. WAITED FOR PARTS. WHEN PARTS ARRIVED, HEATEDTHE HUB AND INSTALLED NEW CUPS. TRAVELED TO UNIT. INSTALLED INSIDE DUO CONE SEALSBEARINGS AND HUB. SET PRELOAD ON BEARINGS. INSTALLED RETAINER AND BOLTS WITH THREADLOCK. TORQUED BOLTS TO 200 FT/LBSCLEANED UP SITE

MAR 29, 11 - JIM MLOADED TOOLING IN TRUCK. TRAVELD TO UNIT. INSTALLED WHEEL NUTS ON LEFT WHEEL ANDTORQUED TO 1000 FT/LBS. LOWERED MACHI NE FROM THESTAND AND JACK. MOVED THE PLATE NDJACK TOTHE RIGHT SIDE OF THE MACHINE. JACKED UP THE UNIT - INSTALLED THE STAND.REMOVED THE RIGHT FRONT FRONT WHEEL NUTS. KAL TIRE REMOVED THE WHEEL. DRAINED OIL.REMOVED WHEEL HUB. FOUND THE INSIDE DUO CONE SEAL PUSHED OUT OF POSITION CAUSINGTHE OVERFILLING. INSTALLED A NEW INNER SEAL UP. CLEANED THE OUTSIDE SEAL ANDREASSMEBLED THE HUB. CALLED KAL TIRE TO INSTALL THE WHEEL. REMOVED PARK BRAKE RELEASEVALVE CYLINDER AND SPOOL. FOUND BROKEN SPRINGS IN THE VALVE. ORDERED PARTS.

APR 4, 11 - DEFECTS - DARREN/MARKLOADED TOOLING AND PARTS. DROVE TO MILDRED LAKE, SET UP @ UNIT. REMOVED DOGBONE,REPLACED BUSHINGS REINSTALLED THE DOG BONE-BROUGHT KEVIN L. BACK TO THE SHOP. WENTBACK TO THE UNIT AND SETUP. ADJUSTED THE STUTS, HOOKED UP THE LAPTOP AND TURNED OFFTHE PRELUBE. REMOVED WINTER FRONT, HAD TO CLEAN UP AREA, AND MOVE THE TRUCK, IT WASIN THE WAY OFTHE CRANES THAT WERE GOING TO BE WORKING IN THE YARD. DROVE BACK TOEMECO

APR 5, 11 - LEEOFF LOAD USED OIL OUT OF LUBE TRUCK. FILL OUT JHA. LOCK OUT, PUT CHALKS IN PLACE. EVACTWO BARRAWS AND TAKE BARRAWS BACK TO EMECO SHOP. MANUALLY GREASE DOG BONE ONTRUCK. TAKE OFF KMC NUMBER OFF OF FRONT GRILL, BOX NUMBERS ARE WELDED ON, HAVE NOWAY TO GET THEM OFF THE TRUCK. THE NUMBER THAT IS OFF IS MARKED AND PUT WITH THEOTHERS BY THE DRY PARTS TENT. CHECK OILS, TOPPED UP IF NEEDED. CALL FADIE TO SEE IF UNITIS DUE FOR SERVICE, LOOKS LIKE TRUCK HASN'T HAD A ENG SERVICE SINCE NEW MOTOR HASBEEN REPLACED, TRUCK IS ACTIVALLY DUE FOR 2000 HR, PM FILTERS ARE ORDERED

APR 7, 11 - KEVIN/JIM MREMOVED FUEL TANK FROM PALLET, LOADED TANK IN TRUCK. FILLED WITH FUEL. TRAVELED TO KMCYARD. PUMPED FUEL INTO UNIT. STARTED UNIT AND WARMED. CHECKED MACHINE OVER.PERFORMED OUT SHEET INSPECTION AND TIRE REPORT. FOUND OIL LEAK AT BRAKE OIL COOLER,MOVED UNIT TO KAL-TIRE. RETURNED TO SHOP. UNLOADED FUEL TANK.

APR 10, 11 - REPAIR HYD OIL LEAK AT FRONT BRAKE DRIVE VALVE MOUNTED ON BRAKE OILCOOLER - KEVINDRIVE TO FINNING, FILLED OUT FLRA, LOCK AND CHALK UNIT OUT OF SERVICE. CLEANED AREAWITH BRAKE CLEAN AND COMPRESSED AIR, REMOVED ALL LINES AND VLAVES, CLEANED ALLSURFACES, INSPECTED FOR CRACKS OR DAMAGE, WAS OK, INSTALLED ALL NEW O-RINGS ANDREASSEMBLED, MISSING 1 O-RING, BRAKE OIL TEMP SENSOR BLOCK, LOOKED ON SIS FOR PARTNUMBER, COULD NOT FIND IT, COVERED OPEN LINES. DROVE TO ANOTHER MECHANIC AT NORTHGATE, HE HAD PROPER O-RING ON HIS TRUCK. SHIFT WAS OVER, DROVE BACK TO EMECO SHOP.VARIFIED O-RING PART NUMBER IN SERVICE MANUAL. NEED TO INSTALL NEW O-RING ON BRAKEOIL TEMP SENSOR BLOCK AND HOOK UP 2 LINES THAT ARE MARKED.

10-Mar-2011 WOC86652 - FILED INSHEET 21,578




INSHEET INSPECTION AT M LAKE FINNING MACHINE JUST CAME OFF RENT FROM KMC

MAR 10, 11 - DARRENINSPECT AT M LAKE FINNING

MAR 20, 11 - THROTTEL CONTROL - GRANTBOTH KMC AND OUT BACKLOG LIST SHOWING THROGGGLE CONTROL NOT REPAIRED. SEPEND 20MIN TRYING TO FIND PART. BUT UNABLE TO FIND AT SHOP. THEY WERE HERE . TRAVEL TOMACHINE WHILE ON SITE. WAIT FOR MACHINE TO FINISH LOADING. CALLED UNTI DOWNA NDCHECKED. REPAIR WAS DONE. TRAVEL BACK TO KMC SHOP. WINDOW FALLING OUT, CAB COORNEEDS REPLACED.

MAR 21. 11 - TRUCK INSPECTION - LEEGOT CALL FROM DAN. NEEDED HELP TO DO A STRING AND DOG BONE TEST. DOGBONE HAVE SOMEPLAY.

MAR 21, 11 - RETURN FORM RENTAL INSPECTION - DAN HTRAVEL TO UNIT, GET STARTED AND WARM UJP. DO INSPECTION AND CHECKOVER ON MACHINE.FILL OUT INSPECTION SHEET AND TRAVEL BAKC TO SHOP.

8-Mar-2011 WOC86549 - START MACHINES 21,535BOOMER KMC REQUESTED TO START MACHINES AT KMC SUNCOR RDC004 , RDC044 AND XHC001

MAR 08, 11 - MARK FORANSTARTED MACHINES FOR KMC, BOOMER REQUESTED. RDC004 - 21, 535 - HAD TO BOOST MACHINERDC044 - 20, 493XHC001 - 21. 995

14-Feb-2011 WOC83738 - BRAKE PROBLEM 21,487TROUBLESHOOT AND REPAIR BRAKE PROBLEM

FEB 14, 11 - REPAIR BRAKE ISSUE - STEPHENTRAVEL TO SUNCOR, GET PERMIT, WAITED 2 HRS FOR ESCORT TO MACHINE. START MACHINE, FOUND PARK BRAKE WOULD RELEASE BUT THE LIGHT WOULD STAY ONE. REMOVED SENSOR, CLEANED OUT ICE, REASSEMBLED, TESTED GOOD.

FEB 17, 11 - BRAKES STICKING - MARK FCHECKED OVER MACHINE, SEEMED OK. ATTACHED COMPUTER, NO ACTIVE CODES. MOVED MACHINE BACK AND FORTH, SEEMED GOOD. OPERATOR TRANSPORTED MACHINE TO DIFFERENT LAYDOWN, 2 KM. AWAY WHEN ARRIVING, BRARKES STARTED TO STICK. CHECKED BRAKES, BOTH REAR HUBS VERY HOT TO TOUCH.

FEB 18, 11 - FINNINGPICK UP PART, DRIVE OUT TO UNIT, CHANGE OUT HARNESS ON L/H FRONT WHEEL. CHANGE OUT 2 HYD LINES, DID NOT RECEIVE STEERING LINKAGE WILL BE HERE IN A FEW DAYS.

FEB 19, 11 - BRAKES STICKING - MARK FFLRA HAS TO BE SIGNED STARTING TODAY BEFORE WORK BEGINS, WAITED FOR FOREMAN. HAD TO START MACHINE, BOOST OFF OF BOOSTER AND BATTERIES THAT ARE IN TRUCK. TRUCK WOULD NOT HEAT UP BRAKES, HAD TO GET OPERATOR TO COME. PIERRE WENT FOR DRIVE WITH OPERATOR, ORDERING PARTS FOR HAND VALVE, RETARDER BRAKE. HANDLE IS LOOSE, COULD BE CAUSE FOR BRAKES STICKING. DID NOT HEAT UP OTHER WISE WHEN GONE FOR DRVIE. REPLACED FUEL SENSOR ON TANK, NEED TO ORDER NEW ONE. SEATS ARE EXPIRED.

FEB 19, 11 - CUSTOMER COMPLAINT OF BRAKE STAYING ON - FINNINGSIGN IN AND GET PERMIT AT SUNCOR. GET ESCORT TO UNIT, WEATHER WAS COLD. HAVE HARD TIME TO GET TRUCK GOING, AFTER GET UNIT GOING, TRY OUT UNIT. BUT COULD NOT GET RUCK TO ACT UP, CALL FOR OPERATOR AND WENT FOR A FEW LOADS WITH OPERATOR, FIND THAT RETARDER LEVER STRIKING ON SOMETHING.

FEB 20, 11 - REPLACE RETARDER VALVE - MARK FREPLACED RETARDER VALVE ON STEERING COLUMN. NEVER STARTED TO CHECK IF WORKED PROPERLY HAD TO LEAVE FOR OTHER JOB.

4-Feb-2011 WOC82754 - STEERING HOSE LEAK 21,292REPAIR STEERING HOSE LEAK MACHINE WIT KMC SUNCOR

FEB 04, 11 - REPAIR FOR STEERING ISSUE - STEPHENPULL OUT PERMIT, ESCORT TO MACHINE. INSPECT MACHINE, FOUND OIL LEAK FROM STEERING LINE, ORDER LINE. CHECK STEERING OPEARTION, ALL SEEMS GOOD OTHER THEN LINE.

FEB 05, 11 - REPLACE STEERING HOSE - MARK REPLACED STEERING HYD HOSE. REPAIRED ANOTHER STEERING LEAK UNDER CAB. BRAKE SYSTEM FROZEN, RAN FOR AWHILE, SEEM TO BE GOOD. LOW ON OIL, KMC ADDED STEERING OIL.




22-Jan-2011 WOC90097 - 250 HOUR SERVICE - KMC 21,017JANUARY 22, 2011 - KMC PERFORM 250 (325) HOUR SERVICE ON UNIT AT 21017 HOURS

15-Jan-2011 WOC80650 - FIRE SUPP PM 20,955LEVITT TO DOFIRE SUPP

JAN 15, 11 - LEAVITTINSPECT TANK, HOSING, DETECTION WIRE, PORTABLES. RAF'S PULLSTATION. BLOWN LINES AND REPLACED CAPS. SHOT TEST AND ENGINE SHUT DOWN NEED TO BE DONE. FINNING MECHANIC NEED TO CHECK ENGINE SHUT DOWN CONNECTIONS.

JAN 16, 11 - LEAVITTGO TO EMECO. T/SHOT, FOUND ONLY 12 VOLTS ON POWER. CHARGED IT TO 24V. ON GOING.

JAN 18, 11 - LEAVITTWAS ASKED TO COMPLETE REPAIRS ON UNIT. I REPAIRED SHOT HARNESS, CAMGED 12 PIN INSIDE PANEL BOX. ENGINE SHUT DOWN DID NOT FUNCTION. I T/SHOT SHUTDOWN AND RECONNECTED CONNECTOR BEHIND THE CAB. SYSTEM OK.

12-Jan-2011 WOC80217 - RF WHEEL SEALS 20,955change out front right wheel seals

JAN 15, 11 - TROY LUNDYPUT TRUCK ON BLOCKING OUTSIDE AFTER FIXING KALTIRES JACKS. REMOVED FRONT R/H WHEEL SEALS. REPLACED FRONT R/H WHEEL SEALS FOR LEAKING. REPLACED W/S WASHER PUMP.

12-Jan-2011 WOC80306 - DEFECT LIST 20,955minor repairs on machineTruck needed to be started at Northgate.

5-Jan-2011 WOC79574 - INSPECTION 20,954INSPECT MACHINEDO TIRE SURVEY

COMPLETED BY SCOTT M

30-Dec-2010 WOC78770 - ENGINE FAILURE 21,182




ENGINE FAILUREREPLACE ENGINE AS REQUIRED

JAN 03, 11 - GET UNIT TO WASH BAY - RICARTE, ROGERRECHARGED BATTERY FOR THE SECONDARY STEERING. WARM UP EXCAVATOR FOR USING TO PUSHRDC004 TO WASH BAY DN PUT IN WASH BAY.

JAN 04, 11 - SUPPLY AFTER FAILURE ENGINE OF RUNIT. PLEASE TAG CORE FOR FAILURE ANALYSIS.FULL PRORATION TO CUSTOMER. UNIT HRS 19956 CMPT HRS 3800 BM 14000 LIFE 28%

JAN 06, 11 - HENRY, AARONREMOVE RAD COVERS AND BATTERIES. REMOVE RAD CORE. DRAIN OUT COOLANT FROM RAD.DRAIN TORQUE CONVERTOR AND HYD TANK. REMOVE STUMP PANS. UNHOOK HEATER HOSES.REMOVE CABLES OFF OF STARTERS. UNHOOK MAIN ENGINE HARNESS. REMOVE AIR COMPRESSORLINES.

JAN 07, 11 - AARONWE ONLY SPENT ABOUT ONE HOUR ON TRUCK. WE REMOVED HYD HOSES FORM BOTTOM OFENGINE. DRAINED ENGINE OIL. REMOVED DRIVE SHAFT.

JAN 07, 11 - TROY LUNDYRAISED BOX. DRAINED HYD TANK. REMOVED AIR CLEANER PLATFORM AND EST. TUBES. PUDUETSH CONNECTORS ON WIRE ACROSS FRONT OF ENGINE. REMOVED CROSS BRADE. REMOVEDFRONT A/C COMP. MOVED NEW ENG OUT OF WALKWAY. DISCONNECTED FUEL SUPPLY LINE.

JAN 08, 11 - TROY, BRUCEFINISHED ENG REMOVAL. WASHED MACHINE DOWN. MOVED NEW ENGINE INTO PLACE.

JAN 09, 11 - TROY, BRUCECON ENG INSTALL.. CONECTED HOSES AND DRIVE SHAFTS. INSTALLED A/C OMP. HOOKED UPHARNESS AND STARTERS. ORDERED PARTS FOR HYD. TANKS HOSES AND O-RINGS.

JAN 10, 11 - TROYFINISHED CONNECTING TRANS CODER LINES. INSTALLED WATER NECK ON REAR COOLER AND ONEEXH PIPE (ORANGE HOSE ON WATER LINE NEEDS TO BE INSTALLED). REASSEMBLED HYD TANK.REMOVED AND CHECKED FILTERS, OK, NEW ELEMENTS AND O-RING ORDERED. INSTALLED HY LINEFROM TORQUE TO HYD TANK.

JAN 11, 11 - TROYRAN WIRING FOR R/H LIGHTS. TIGHTENED RAD COVER AFTER WELDING CRACKS. FILLEDSTEERING OIL. INSTALLED BATTERIES AND MADE NEW CABLE. INSTALLED FIRE EXT. CHECKEDOVER THEM, RAN MACHINE WITH FINNING MECH. ADJUSTED OIL LEVELS. REPAIRED FOR NOTMAKING OF AIR PRESS.

JAN 11, 11 - HENRY , DALEBOX PM IN THE BOX. BOLTED AT THE BELLY PAN. OIL CHANGED AND OIL FILTERS. TOP COVERSARE INSTALLED.

JAN 12, 11 - TROYREPLACED ENG WITH EXCHANGE UNIT. WELDED BROKEN BRACKET ON CAB WALKWAY. CLEANEDOVER FLOWED GREASE FROM AUTO GREASER TANK. ADJ OIL LEVEL IN SUPP STEERING TANK.WENT THROUGH DEFICIENCY LIST TO REPAIR RELEVANT DEFICTS. REPLACED W/S WIPER BLADE.LOUVER FOR FLOOR VENT REPLACED AS IS MISSING CAB FILTER RETAINER.

NOT DATED , DALE, HENRYINSTALLED UPPER CROSS MEMBER, FAN, RAD, ROUTE ELECTRICAL WIRING/ BATTERY CABLES,ROUTE COOLANT LINES.

NOT DATED, DALE, HENRYINSTALLED HYD LINES OFF OF TANK. INSTALLED ORANGE HOSE TO COOLER. INSTALLED RHSEXHAUST. INSTALLED RAD ELBOWS. FILLED RAD WITH COOLANT. INSTALLED HY FILTERS ANDFILLED ONLY TO HALF. INSTALLED AIR FILTERS.

NOT SIGNED OR DATEDSWITCH OVER COMPONETS FOR OLD TO NEW. INSTALL NEW ENGINE IN PLACE. INSTALL OLDENGINE ON STAND.

JAN 06, 11 - GLADIATORATTEMPT TO RAISE BOX WITH INOPERABLE ENGINE. GOT BOX TO RAISE. PULLED OUT OF WASHBAY. PROCEEDED TO TRY AND RAISE BOX. GOT BOX LIFTED ABOUT 3 1/2 FEET. BLOCKED BOX ATTHAT HEIGHT. PUSHED INTO SHOP TO PULL ENGINE.

JAN 09, 11 - GLADIATORGET PARTS FROM FINNING.

JAN 11, 11 - FINNING




CHECKED UNIT AND TOPPED UP OILS. STARTED AND CHECKED FOR LEAKS. NO LEAKS AND ENGINEWAS RUNNING FINE. UNIT WOULD NOT BUILD AIR PRESSURE. T/SHOT UNLOADER VALVE WASROBBED FOR ANOTHER UNIT. REPLACED VALVE, RESTARTED, EVERYTHING OK. LOWERED BOX.CHECK FLUIDS AGAIN AND TOPPED UP HYD OIL STARTED INSTALLING STUMP GAURDS. CLEANEDUP FOR NEXT SHIFT.

29-Dec-2010 WOC78741 - ENGINE NOISE 20,954Diagnose problem and report

DEC 29, 10 - ENGINE KNOCK - GRANTTRAVEL TO KMC, SIGN IN, GET SUNCOR PERMITS, TRAVEL TO ENTRANCE POINT "D". WAIT FOR CLEARANCE FROM SUNCOR. TRAVEL TO MACHINE. TALKED TO WYLIE FROM FINNING WHO DID ORIGINAL CHECKS. DEEP KNOCK. TRUCK PARKED IN CORNER. START AND CHECK. SUSPECTED BROKEN CRANK OR HOLE IN PISTON. GET OIL FILTER BROUGHT OUT FROM KMC SHOP. REMOVE OIL FILTER AND CUT OPEN, FULL O FSTTE. INSTALL NEW OIL FILTER. ENGINE HAS FAILED.

DEC 30, 10 - ENGINE FAILURE, STEEL IN FILTERS - GRANTCOMPLETED PAPER WORK, TIMESHEETS AND SERVICE REPAORTS FROM PREVIOUS DAY. TRAVEL TO SITE, SIGN IN AT KMC. PULL PERMITS AT SUNCOR. CALL SUNCOR FOR CLEARANCE TO ENTER MINE. TRAVEL TO MACHINE. CHECK ENGINE HOT AND READY TO START. SHIFT SOCKS TO BETTER HEAT ENGINE. FLOAT TRUCK WAS MEANT TO BE IN AT 8:30, NEVER SHOWED UNTIL 4PM.

DEC 31, 10 - ENGINE FAILED, HOLE IN BLOCK - GRANTCALLED BY SUPERVISOR "MARK" THAT ENGINE HAD AN HOLE IN BLOCK. CHECK LOADING ARE IN 305 FOR SIGN OF FAILURE, NONE. LOADED BY GREG "BOOMHAVEN" FROM KMC . CALLED AND HE STATED WAS RUNNING AND SHUT OFF ONCE ON FLOAT HAND'T FAILED AT THAT STAGE. ASKED TO INSPECT NORTH GATE FOR EVIDENCE OF FAILURE. PACK UP TOOLS, TRAVEL TO KMC YARD MEET UP WITH GREG FROM KMC AND TOOK HIS PICK UP TO NORTH GATE FOUND EVIDENCE OF FAILURE. OIL ON GROUND, CHUNKS OF BLOCK AND DOOR ON GROUND. SNOW HAD BEEN KICKED OVER TO HIDE OIL SPILL. DIDN'T HAVE CAMERA AND KMC CAMERA WAS FLAT. TOOK TWO PHOTOS WITH CELL PHONE. RANG MAKR AND CONFIRMED SITE OF FAILURE. NORTH GATE SUNCOR. TRAVEL BACK TO PREVIOUS JOB, GET CLEARANCE FROM SUNCOR.

DEC 31, 10 - GLADIATOR START UP 850 HITACHI. GET RIGGING TO PULL OFF TRUCK. RIG UP MACHINE TO HOE. LOOK FOR HOSE TO PRESSURE UP AIR SYSTEM. GOT TO LEO ROBERTS FOR FITTINGS FOR AIR DRYER. T/SHOOT HOW TO RELEASE PARK BRAKE. CHANGE VALVE POSITION ON DIVERTER VALVE. PULL OFF TRUCK. TOW TRUCK IN YARD. CLEAN UP

24-Dec-2010 WOC78459 - REPAIR SEAT 20,917REPAIR SEAT

DEC 24, 10 - SEAT CLICKING , RETARDER TEMP LIGHT FLASHING OFF AND ON - GRANTTRAVEL TO MACHIEN @ LIMESTONE PIT. CHECK SEAT, FOUND SEAT BASE CRACKED AND BROKEN. INTERMITTANT ELECTRICAL ALARM ON BRAKE TEMP SENSOR OK TO RUN AS SIX OTHER UNITS DOWN.

DEC 27, 10 - TRANNY TEMP ALARM, SEAT BASE BROKEN - GRANTTRAVEL TO MACHINE IN MINE. UNIT WAS IN USE SO WAIT FOR OPEARTOR TO COMPLETE CYCLE. LOCK AND CHOCK TRUCK. T/SHOOT TRANSMISSION TEMP ALALRM, FOUND TEMP SENSOR FAULTY. REPLACED 118-7226 SENSOR WITH ONE FROM TRUCK STOCK. TESTED OK. REMOVE SEAT BASE CRACKED AT LOWER SHOCK MOUNT. INSTALL NEW BASE AND SLIDES. RE-INSTALL SEAT TO BASE. CALL SUNCO R656 SUPERVISOR FOR CLEARANCE TO LEAVE MINE. TRAVEL BACK OFF SITE.

16-Dec-2010 WOC77727 - 2000 HR PM SERVICE 20,6662000 HR PM SERVICECOMPLETED BY KMC

23-Nov-2010 WOC75762 - 2000 HR PM SERVICE 20,1282000 HR PM SERVICECOMPLETED BY KMC

28-Oct-2010 WOC72009 - 1200 HR PM FIRE SUPPRESSION 19,7381200 HR PM FIRE SUPPRESSION

NOV 03, 10- FIRE SUPPRESSION - LEVITTECHECKED ALL HOSES/NOZZLES/FITTINGS. TESTED PANEL. TESTED ENGINE SHUTDOWN. CHECKED BOTTLES, CONTROL HEAD AND PRESSURE. TESTED IR'S/DAF'S. CHECKED WIRING AND PULL STATIONS. CHECKED FIRE EXTINQUISHERS, FOUND 2 MISSING BOLTS IN TANK BRACKET. REPLACED ONE NOZZLE, SYSTEM OK.

13-Oct-2010 WOC72582 - 1750 HR PM SERVICE (KMC) 19,3941750 HR PM SERVICE COMPLETED BY KMC

4-Oct-2010 WOC69836 - CHANGE 4 REAR TIRES 19,306




Supply 2 rims - cracked

CHANGE 4 REAR TIRES. SUPPLY 2 RIMS, OLD ONE CRACKEDTIRE TO BE RETURNED TO KAL-TIRE.2 RIMS - 1 CRACKED, 1 PARTIAL RIM TO BE RETURNEDARNOLD FROM KMC CALLED

30-Sep-2010 WOC69493 - CHANGE TIRE 19,296L:RI tire separated.

COMPLETEDNO OTHER INFONO HOURS REPORTED

29-Sep-2010 WOC69380 - BACK CHARGE 19,296No start - customer asked to machine started. No machine was at the location. It had been started and was being used.

SEPT 28, 10 - KEVIN L CUSTOMER ASKED TO HAVE MACHINE STARTED. DROVE TO MACHINE LOCATION, MACHINE WAS NOT THERE. MACHINE WAS ALREADY STARTED AND HAD LEFT. NOTIFIED CUSTOMER JOHN 780-881-0866.

1-Sep-2010 WOC66628 - REPLACE ALTENATOR 19,030Install Altenator and belt.

SEPT 01, 10 - BATTERY LIGHT ON - GRANTTRAVEL TO UNIT, FOUND ALTERNATOR BEARING FAILED AND ALTERNATOR HOWLING. OPEN W/O, ORDER PARTS. TRAVEL TO FINNING AND PICK UP PARTS. REMOVE AND INSTALL ALTERNATOR WITH OR ALT. TEST OK. REINTALL GUARD, BELT REPLACED AS CRACKING. CLEAN UP. LOCKS AND CHOCKS REMOVED.

25-Aug-2010 WOC66278 - 1750 HR SERVICE 18,992KMC DID A 1750 HR SERVICE AUG 25 AT 18992 HRS

17-Aug-2010 WOC64744 - IN SHEET INSPECTION 18,956Tire report Fill in sheets and submit.

AUGUST 20,10: DEFECT LIST REPAIRS:CHECKED TRUCK FOR ANTIFREEZE LEAK, FOUND THAT MAIN RAD RELIEF VALVE GASKIT LEAKING. REPAIRED LEAK TOPPED ANTIFREEZE UP AND FILLED OUT PRE RENTAL SHEET.

6-Aug-2010 WOC63295 - LIGHTS 18,924REPAIR HEAD LIGHTS

AUGUST 5,10: BATTERY LIGHT:BATTERY LIGHT COMING ON AND OFF. TESTED ALT. ALT. IS GOOD 27AMP. FOUND BATTERY LIGHT WIRE LOSE. TIGHTENED UP. GOOD TO GO +HEAD LIGHT.

14-Jul-2010 WOC61146 - HOIST HOSE 18,908REPLACE LH HOIST CYLINDER HOSE

JULY 15,10: RE & RE HYDRO HOSE:WENT TO FINNING GOT HOSE MADE. RE & RE IT ON THE MACHINE. TOP UP TANK. GOOD TO GO.

24-Jun-2010 WOC58420 - 1500 HR PM 18,7101500 HR PM SERVICE MACHINE AT NACGGO TO UNIT AFTER GRABBING PARTS FROM FINNING. CALL LUBE TRUCK. SPIN FILTERS. TOP UP FUEL ENGINE OIL. SAMPLES, CHECKS AND TEST. RELEASED UNIT WORK.

9-Jun-2010 WOC56730 - CHECK A/C FUNCTION 18,420CHECK PRESSURE/CLUTCH BELTS ETC.

FINNINGTROUBLESHOOT A/C, CONNECT GUAGES, START MACHINE, CHECK PRESSRES WAS A BIT LOW BUT COMPRESSOR WAS CYCLEING. INSTALLED 1LBS OF REFERIERENT, RAN MACHINE OK.

24-May-2010 WOC54705 - B&S TEST 18,423Fill out comleted form and submit.B & S TEST

9-May-2010 WOC53267 - INSTALL P BRK INDICATOR SYSTEM 18,419




Install wheel chock holdersInstall 2 nd fire extinguisher if requiredinstall customer decals.Repaired crack on Rad Housing by hand rail bolts.Welded on plate for extinguisher.Clean Cab

22-Apr-2010 WOC51647 - BACK CHARGE 18,418BACK CHARGEREPARIR / REPLACE STEP ASSEMBLY

APR 22, 10 - REPAIRS AND PREP TO GO TO WORK - GARNETTRAVELLED FROM FOR MCKAY TO SUNCOR - VIA FINNING @ MILDRED LAKE TO PICK UP PARTS. ARRIVED @ TRUCK AND DETERMINED THAT SHORT SHIPPED STEP STRAPS IN PARTS ORDER. APPARENTLY STRAPS WERE IN STOCK IN EMECO PARTS AND HAD NOT BEEN INFORMED. SO DUE TO THE URGENSY OF GETTING THIS TRUCK READY TO GO TO WORK, STOLE STRAPS FROM RDC012 R/SH STEP (THESE STEPS WERE MANGLED AND BENT BUT STRAPS SEEMED OK). ASSEMBLED STEPS AND MOUNTED ON TRUCK, AFTER COMPLETION NOTICED THAT RUNG SPACING WAS UNEQUAL AND AFTER CAREFUL EXAMINATION IT SEEMS THAT THE STRAPS FROM RDC012 WER NOT OEM CAT STRAPS AND ACQUIRED FROM ANOTHER SOURCE. SHOULD BE SERVICABLE ENOUGH BUT WILL NEED REPLACING IN THE FUTURE.

22-Apr-2010 WOC51648 - REPAIR SHIFT ASSEMBLY 18,419REPAIR SHIFT ASSEMBLY

APR 22, 10 - REPAIRS AND PREP TO GO TO WORK - GARNETDISASSEMBLED TRANS SHIFTER SHAFT AND DETENT ASSEMBLY TO DETERMINE WHY CONTROL WERN'T OPERATING NORMALLY. DETERMINED THAT WHEN BRACKET FOR 2-WAY RADIO WAS ATTACHED TO CONSOLE - INSTALLER HAD DRIVEN A SELF TAPPING SCREW DIRECTLY INTO TRANS SHIFTER SHAFT AND FORCED SHAFT AND BEARING OUT OF BORE AND THEN THE DETENT BALLS WOULD NOT ALIGN WITH THEIR APPROPRIATE DETENTS. DISASSEMBLED DETENT HOUSING AND CLEANED AND POSITIONED BEARING BACK INTO PROPER LOCATION AND ENSURED SHAFT WAS ALIGNED ACCORDINGLY. INSTALLED NEW BALLS ( SPRING AND PINS BACK ORDERRED). AND REASSEMBLED. CUT OFF SELF TAPPING SCREW AND INSTALLED SHIFT AND DETENT HOUSING CHANGED WITH SHIFTER LEVER AND TRANS SENSOR. TESTED UNIT AND SEEMS OK. CHARGED SUSPENSION CYLINDERS - ISSUES AND TROUBLES WITH OLD STYLE SCHRADER VALUES NOT SEALING. TIMECONSUMING TO OVERCOME PROBLESM REPAIRED LEAK @ PRIMARY FUEL SCREEN. REMOVED TARP FROM GRILL.TALKED TO TERRY @ THOMPSON BROTHERS AND ASKED IF HE COULD HAVE HIS LUBE TRUCK FILL THE AUTO LUBE RESEVOIR ON THIS TRUCK AND RDC005 BEFORE THEY LEFT FOR ANOTHER SITE.

APR 23, 10 - GARNETCOMPLETED PAPER WORK FROM PREVIOUS DAYS FIELD CALL. RE-INSTALLED SHIFTER SHAFT IN RDC013 ROBBED IN CASE NEEDED IN REMOTE SITEMay 5 09 - Outsheet inspection - Repiar lights Left rear box wiring.Install fire extinguisher and bracket

21-Apr-2010 WOC51613 - INSHEET INSPECTION 18,418INSHEET INSPECTION - COMPLETED

6-Apr-2010 WOC49638 - 1200 HR FIRE SUPPRESSION 18,4171200 HR FIRE SUPPRESSION

APR 06, 10 - LEVITTE, ROYDID A 1200 HR PM ON UNIT. METERED PANEL, CONDUCTED ENGINE SHUT DOWN, BLEW LINES, CHECKED PORTABLE EXTINQUISHER, DAF'S, WIRE AND HOSE CONNECTIONS. UPON CHECKING USED ONE OF 1" HOSE WRAP AND PUT EXTINQUISHER BAGS (NEW ) ON EXTINQUISHERS. SYSTEM OK.

27-Feb-2010 WOC45194 - FIRE SUPPRESSION (INCOMPLETE) 18,130Thompson would not give the trucks after allowing us on site.

CUSTOMER WOULD NOT ALLOW US TRUCKS AFTER ENTRY ON THE SITE.

26-Feb-2010 WOC45113 - TIRE INSPECTION (KAL-TIRE) 18,130TIRE INSPECTION (KAL-TIRE) - COMPLETED

18-Feb-2010 WOC44044 - COLD START MACHINE (FINNING) 18,147




GET TRUCK STARTED FOR TRANSPORT FROM SUSAN LAKE PIT TO SUNCOR

FEB 18, 10 - TRUCK WOULDN'T START - DARRENLOADED UP TOOLS ONTO TRACK. DROVE TO SUSAN LAKE GRAVEL PIT. FILLED OUT FLRA. FOUNDTRUCK WOULD NOT CRANK DUE TO LOW BATTERIES. MOVED ANOTHER TRUCK OVER AND HOOKEDUP JUMPER CABLES. REMOVED AIR CLEANERS AND USED SOME ETHER TO START TRUCK. STARTEDIT AND DISCONNECTED CABLES AND REPACKED OTHER TRUCK. CLEANED UP AND DROVE BACK TOSITE.

FEB 21, 10 - AFTER CUSTOMER ( THOMPSON BROS ) LEFT MACHINE RUNNING AND DID NOT PICK ITUP IT RAN OUT OF FUEL.FUELED UP MACHINE, BLED AND BOOSTED.CHANGE GROUND CLAMP AND HOLD DOWN ON BATTERY

FEB 21, 10 - CHANGED STARTING BATTERY END CABLE - JERAMEY & RICKYTRAVEL TO THE MACHINE, WE OPEN BATTERY BOX, FOUND OUT THE STARTING BATTERY ANGLE ABIT SO WE TOOK THE BOLT FROM CLAMP IN ORDER TO SQUARE THE BATTERY. WE FOUND ALSOTHAT THE BOLT NEED MORE WASHER TO GET MORE CLAMPING FORCE. WE REPLACED THE BATTERYEND DABLE (NEGATIVE TERMINAL). WE TESTED AFTER WE REPLACED, IT WORK GOOD. WE PUT THECOVER BACK ON AND MOVE ON TO THE NEXT JOB. ALSO STRAIGHTENED BATTERY LIDDOWNBRACKET.

FEB 21, 10 - FINNINGBLED FUEL SYSTEM AND STARTED MACHINE _ MACHINE HAD RAN OUT OF FUEL.

3-Feb-2010 WOC42258 - REPLACE PARK BRAKE PRESSURE SW 17,729REPLACE PARK BRAKE AIR PRESSURE SWITCH FOR LIGHT.

25-Jan-2010 WOC41266 - CHARGE FRONT STRUTS 17,974charge front struts

15-Jan-2010 WOC40278 - FRONT STEERING LINK/TIE ROD EN 17,972REPAIR FRONT STEERING LINK AND TIE ROD ENDS

CHANGE FAN MOTORREPLCED BALL STUD IN BOTH RIGHT AND LEFT TIE RODSINSTALLED NEW CENTRE PIN IN CENTER LINKINSTALLED NEW HEATER MOTOR

15-Jan-2010 WOC40275 - 1000 HR PM SERVICE 17,9741000 HR PM SERVICECUT OPEN FILTERS/REPORT SAMPLE COMPARTMENTS

15-Jan-2010 WOC40279 - VALVE SET 17,974VALVE SET

4-Jan-2010 WOC38868 - REPAIR BODY UP SWITCH 17,053REPAIR BODY UP SWITCH DONE BY FINNING

28-Dec-2009 WOC38496 - FUMES GETTING IN CAB 17,708FUMES GETTING INTO CABCHECK THE SOURCE OF THE LEAK AND FIX

DEC 28, 09 - CUSTOMER COMPLAINED ABOUT FUMES GETTING INTO CAB - RICARTETRAVELLED TO THE MACHINE, PUT WHEEL CHUCK ON. WENT INTO THE CAB AND TURNEDTHE HEATER FAN OVER. I WENT UNDER THE CAB TO CHECK IF THERE WAS ANY SMOKE THAT WAS POSSIBLY DRAWN INTO THE CAB. I FOUND ONE TURBO CLAMP WAS LOOSE. I TURNED OFF THE MACHINE TO GET THAT CLAMP TIGHT. AFTER I TRIED TO STARTTHE MAHCINE BUT IT WOULDN'T START. BATTERY WAS WEAK, SO I OPENED THE BATTERY BOX COVER AND FOUND THAT ONE OF THE BATTERY TERMINALS WAS NOT HOOKED UP PROPERLY. CLAMP WAS SEAT ON TOP OF THE POST. I TIGHTEND AND SECURED ALL THE OTHER TERMINALS. I FOUND THAT ONE OF THE GRAB RAILS ON THE RIGHT HAND SIDE WAS BROKEN, WELDING BROKEN OFF. NEED TO BE WELDED TOGETHER.

21-Dec-2009 WOC37802 - FIRE SUPPRESSION SERVICE CALL 17,550Levitt Safety checking on unit problem

WAS INFORMED FROM GRANT OF A TROUBLE CALL. ARRIVED @ COW HARBOUR. METERED PANEL. PANEL INDICATED DL ON DAF. CHECKED DAF. UPON CHECKING FOUND BROKEN WIRE ON THE WIRE HARNESS SIDE. REPLACED OEM. REMETERED PANEL. SYSTEM OK.

18-Nov-2009 WOC28682 - VALVE SET & OIL CHANGE 16,918VALVE SETOIL CHANGE

5-Nov-2009 WOC27243 - CENTRE STEERING LINK 16,918CANCELLED NEW WO 40278





Documents

PICTURE TO COME · source hyd leaks, replaced trans input seal 2014/01/16-cs paul austin clark clean off plate, drill, tap and install fittings-look for hose-found @ aurora laydown