A: Conductor:1/0 AWG Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

748*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.355 0.362 0.366

0.012 0.018 ‐‐ ‐‐ 0.398 ‐‐

0.330 0.345 0.375 1.045 1.088 1.145

‐‐ 0.005 ‐‐ ‐‐ 1.163 ‐‐

0.024 0.030 0.060 1.095 1.148 1.235

0.070 0.080 0.105 ‐‐ 1.323 ‐‐

Insulation Level100%

Conductor Weight99

Met. Shield Weight84

Cable Weight

Electrical Properties

Cable Description: 1/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.189 0.619Rac @ 25°C: 0.189 0.619Rac @ 105°C: 0.248 0.814

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.584 1.915Rac @ 95°C: 0.741 2.431

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.039 0.127µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 68,336 20,829Shunt Capacitive Susceptance: 14.63 48.01

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 291.2 955.3mA/kf mA/km

4.05 13.30Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 53.22 V/mil 2,095.22 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 99.79 3,928.80V/mil V/mmInsulation ‐ Insulation Shield Interface: 36.28 V/mil 1,428.52 V/mm

Insulation Resistance: 8,734.9 2,662.4Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault11,737 9,351 7,715AmpsAmps Amps

3,525 2,966 2,57710 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

1/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.323 in

435.3 132.7ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

Conductor Spacing (S): 1.323 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.249Real

0.052Imag.

Inductice Reactance: 0.051Impedance

0.254 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.816 0.169 0.833

0.168 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.608 0.364 0.709 Ω/kft 1.995 1.195 2.325 Ω/kftZero Seq. Impedance (Earth Only): 0.302 0.750   Ω/kft 0.992 2.462 2.442 Ω/kft

Electrical Properties ContinuedCable Description: 1/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 202

75% Load Factor: 230 AmpsAmps

Conductor Spacing (S): 1.323 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.249Real

0.057Imag.

Inductice Reactance: 0.057Impedance

0.256 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.818 0.188 0.839

0.188 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.603 0.363 0.703 Ω/kft 1.977 1.190 0.839 Ω/kftZero Seq. Impedance (Earth Only): 0.302 0.739 0.798 Ω/kft 0.992 2.423 2.619 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 202

75% Load Factor: 230 AmpsAmps

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.252Real

0.096Imag.

Inductice Reactance: 0.097Impedance0.269 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.826 0.826 0.884

0.317 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.608 0.352 0.663 Ω/kft 1.844 1.153 2.175 Ω/kftZero Seq. Impedance (Earth Only): 0.302 0.660 0.726 Ω/kft 0.992 2.166 2.382 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 223

75% Load Factor: 249 AmpsAmps

Installation PropertiesCable Description: 1/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 845 3.8 1690 7.5Cable Basket Grip: 845 3.8 1690 7.5

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 16 40312xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:2/0 AWG Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

807*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.398 0.406 0.410

0.012 0.018 ‐‐ ‐‐ 0.442 ‐‐

0.330 0.345 0.375 1.090 1.132 1.190

‐‐ 0.005 ‐‐ ‐‐ 1.207 ‐‐

0.024 0.030 0.060 1.140 1.192 1.280

0.070 0.080 0.105 ‐‐ 1.367 ‐‐

Insulation Level100%

Conductor Weight128

Met. Shield Weight88

Cable Weight

Electrical Properties

Cable Description: 2/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.146 0.478Rac @ 25°C: 0.146 0.478Rac @ 105°C: 0.192 0.629

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.563 1.846Rac @ 95°C: 0.714 2.342

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.042 0.136µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 63,872 19,468Shunt Capacitive Susceptance: 15.66 51.37

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 311.5 1,022.0mA/kf mA/km

4.34 14.23Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 53.74 V/mil 2,115.76 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 96.04 3,781.00V/mil V/mmInsulation ‐ Insulation Shield Interface: 37.31 V/mil 1,468.85 V/mm

Insulation Resistance: 8,168.5 2,489.8Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault14,768 11,761 9,699AmpsAmps Amps

3,660 3,079 2,67610 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

2/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.367 in

428.7 130.7ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A2/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 1.367 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.192Real

0.049Imag.

Inductice Reactance: 0.049Impedance

0.198 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.631 0.162 0.651

0.162 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.550 0.049 0.552 Ω/kft 1.804 0.162 1.811 Ω/kftZero Seq. Impedance (Earth Only): 0.246 0.747 0.786 Ω/kft 0.807 2.450 2.580 Ω/kft

Electrical Properties ContinuedCable Description: 2/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 232

75% Load Factor: 265 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 1.367 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.191Real

0.055Imag.

Inductice Reactance: 0.055Impedance

0.199 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.627 0.181 0.653

0.182 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.542 0.350 0.645 Ω/kft 1.780 1.147 0.653 Ω/kftZero Seq. Impedance (Earth Only): 0.246 0.735 0.775 Ω/kft 0.807 2.410 2.542 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 232

75% Load Factor: 265 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.196Real

0.093Imag.

Inductice Reactance: 0.094Impedance0.217 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.643 0.643 0.712

0.308 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.550 0.340 0.609 Ω/kft 1.659 1.115 1.999 Ω/kftZero Seq. Impedance (Earth Only): 0.246 0.657 0.702 Ω/kft 0.807 2.157 2.303 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 256

75% Load Factor: 287 AmpsAmps

Installation PropertiesCable Description: 2/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 1065 4.7 2130 9.5Cable Basket Grip: 1065 4.7 2130 9.5

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 16 41712xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A2/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:3/0 AWG Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

877*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.447 0.456 0.461

0.012 0.018 ‐‐ ‐‐ 0.492 ‐‐

0.330 0.345 0.375 1.140 1.182 1.240

‐‐ 0.005 ‐‐ ‐‐ 1.257 ‐‐

0.024 0.030 0.060 1.190 1.242 1.330

0.070 0.080 0.105 ‐‐ 1.417 ‐‐

Insulation Level100%

Conductor Weight157

Met. Shield Weight90

Cable Weight

Electrical Properties

Cable Description: 3/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.115 0.376Rac @ 25°C: 0.115 0.377Rac @ 105°C: 0.151 0.496

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.540 1.773Rac @ 95°C: 0.685 2.247

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.045 0.146µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 59,501 18,136Shunt Capacitive Susceptance: 16.81 55.14

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 334.4 1,097.1mA/kf mA/km

4.66 15.28Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 54.22 V/mil 2,134.75 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 92.53 3,642.85V/mil V/mmInsulation ‐ Insulation Shield Interface: 38.35 V/mil 1,509.74 V/mm

Insulation Resistance: 7,613.0 2,320.5Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault18,599 14,806 12,205AmpsAmps Amps

3,814 3,208 2,78810 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

3/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.417 in

421.7 128.5ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A3/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 1.417 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.152Real

0.048Imag.

Inductice Reactance: 0.048Impedance

0.159 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.497 0.156 0.521

0.156 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.506 0.336 0.608 Ω/kft 1.661 1.104 1.994 Ω/kftZero Seq. Impedance (Earth Only): 0.205 0.742 0.770 Ω/kft 0.673 2.435 2.526 Ω/kft

Electrical Properties ContinuedCable Description: 3/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 265

75% Load Factor: 303 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 1.417 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.151Real

0.054Imag.

Inductice Reactance: 0.054Impedance

0.160 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.495 0.176 0.525

0.176 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.499 0.334 0.601 Ω/kft 1.638 1.096 0.525 Ω/kftZero Seq. Impedance (Earth Only): 0.205 0.730 0.758 Ω/kft 0.673 2.395 2.488 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 265

75% Load Factor: 304 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.156Real

0.091Imag.

Inductice Reactance: 0.091Impedance0.180 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.511 0.511 0.591

0.300 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.506 0.327 0.568 Ω/kft 1.524 1.074 1.864 Ω/kftZero Seq. Impedance (Earth Only): 0.205 0.655 0.686 Ω/kft 0.673 2.148 2.251 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 292

75% Load Factor: 328 AmpsAmps

Installation PropertiesCable Description: 3/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 1342 6 2685 ####Cable Basket Grip: 1342 6 2685 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 17 43212xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A3/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:4/0 AWG Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

960*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.502 0.512 0.517

0.012 0.018 ‐‐ ‐‐ 0.548 ‐‐

0.330 0.345 0.375 1.195 1.238 1.295

‐‐ 0.005 ‐‐ ‐‐ 1.313 ‐‐

0.024 0.030 0.060 1.245 1.298 1.386

0.070 0.080 0.105 ‐‐ 1.473 ‐‐

Insulation Level100%

Conductor Weight196

Met. Shield Weight95

Cable Weight

Electrical Properties

Cable Description: 4/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.089 0.293Rac @ 25°C: 0.089 0.294Rac @ 105°C: 0.118 0.386

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.516 1.694Rac @ 95°C: 0.656 2.152

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.048 0.157µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 55,304 16,857Shunt Capacitive Susceptance: 18.08 59.32

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 359.8 1,180.4mA/kf mA/km

5.01 16.44Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 54.66 V/mil 2,151.94 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 89.31 3,515.97V/mil V/mmInsulation ‐ Insulation Shield Interface: 39.38 V/mil 1,550.44 V/mm

Insulation Resistance: 7,078.8 2,157.6Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault23,420 18,637 15,358AmpsAmps Amps

3,986 3,353 2,91310 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

4/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.473 in

414.3 126.3ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A4/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 1.473 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.118Real

0.046Imag.

Inductice Reactance: 0.046Impedance

0.127 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.388 0.151 0.416

0.150 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.469 0.046 0.472 Ω/kft 1.540 0.151 1.547 Ω/kftZero Seq. Impedance (Earth Only): 0.172 0.738 0.757 Ω/kft 0.564 2.420 2.484 Ω/kft

Electrical Properties ContinuedCable Description: 4/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 303

75% Load Factor: 349 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 1.473 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.118Real

0.052Imag.

Inductice Reactance: 0.052Impedance

0.129 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.386 0.169 0.422

0.169 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.463 0.319 0.563 Ω/kft 1.520 1.047 0.422 Ω/kftZero Seq. Impedance (Earth Only): 0.172 0.726 0.746 Ω/kft 0.564 2.383 2.448 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 310

75% Load Factor: 349 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.123Real

0.088Imag.

Inductice Reactance: 0.089Impedance0.151 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.402 0.402 0.495

0.291 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.469 0.314 0.533 Ω/kft 1.411 1.031 1.747 Ω/kftZero Seq. Impedance (Earth Only): 0.172 0.652 0.674 Ω/kft 0.564 2.140 2.213 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 333

75% Load Factor: 376 AmpsAmps

Installation PropertiesCable Description: 4/0 AWG FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 1693 7.5 3386 ####Cable Basket Grip: 1693 7.5 3386 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 18 44912xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A4/0‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:250 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

1,039*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.547 0.558 0.564

0.016 0.022 ‐‐ ‐‐ 0.602 ‐‐

0.330 0.345 0.375 1.250 1.292 1.350

‐‐ 0.005 ‐‐ ‐‐ 1.367 ‐‐

0.024 0.030 0.060 1.300 1.352 1.330

0.070 0.080 0.105 ‐‐ 1.527 ‐‐

Insulation Level100%

Conductor Weight238

Met. Shield Weight99

Cable Weight

Electrical Properties

Cable Description: 250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.075 0.247Rac @ 25°C: 0.076 0.248Rac @ 105°C: 0.099 0.326

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.496 1.627Rac @ 95°C: 0.630 2.065

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.051 0.168µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 51,804 15,790Shunt Capacitive Susceptance: 19.30 63.33

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 384.1 1,260.1mA/kf mA/km

5.35 17.55Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 54.99 V/mil 2,165.13 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 86.73 3,414.46V/mil V/mmInsulation ‐ Insulation Shield Interface: 40.26 V/mil 1,585.14 V/mm

Insulation Resistance: 6,633.3 2,021.9Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault27,652 22,000 18,125AmpsAmps Amps

4,152 3,493 3,03510 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.527 in

406.1 123.8ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A250‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 1.527 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.100Real

0.044Imag.

Inductice Reactance: 0.045Impedance

0.109 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.328 0.146 0.359

0.146 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.448 0.308 0.543 Ω/kft 1.469 1.010 1.783 Ω/kftZero Seq. Impedance (Earth Only): 0.154 0.735 0.751 Ω/kft 0.504 2.411 2.463 Ω/kft

Electrical Properties ContinuedCable Description: 250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 333

75% Load Factor: 384 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 1.527 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.100Real

0.051Imag.

Inductice Reactance: 0.051Impedance

0.112 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.327 0.166 0.367

0.167 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.441 0.306 0.537 Ω/kft 1.448 1.003 0.367 Ω/kftZero Seq. Impedance (Earth Only): 0.154 0.722 0.738 Ω/kft 0.504 2.368 2.421 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 333

75% Load Factor: 384 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.105Real

0.086Imag.

Inductice Reactance: 0.087Impedance0.135 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.343 0.343 0.444

0.284 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.448 0.302 0.510 Ω/kft 1.346 0.992 1.672 Ω/kftZero Seq. Impedance (Earth Only): 0.153 0.650 0.668 Ω/kft 0.504 2.133 2.192 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 365

75% Load Factor: 413 AmpsAmps

Installation PropertiesCable Description: 250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 2000 8.9 4000 ####Cable Basket Grip: 2000 8.9 4000 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 18 46512xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A250‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:350 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

1,212*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.648 0.661 0.668

0.016 0.022 ‐‐ ‐‐ 0.705 ‐‐

0.330 0.345 0.375 1.355 1.395 1.455

‐‐ 0.005 ‐‐ ‐‐ 1.470 ‐‐

0.024 0.030 0.060 1.405 1.455 1.545

0.070 0.080 0.105 ‐‐ 1.630 ‐‐

Insulation Level100%

Conductor Weight326

Met. Shield Weight106

Cable Weight

Electrical Properties

Cable Description: 350 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.054 0.177Rac @ 25°C: 0.054 0.178Rac @ 105°C: 0.071 0.233

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.461 1.512Rac @ 95°C: 0.585 1.918

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.057 0.188µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 46,271 14,103Shunt Capacitive Susceptance: 21.61 70.90

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 430.0 1,410.8mA/kf mA/km

5.99 19.65Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 55.53 V/mil 2,186.03 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 82.84 3,261.25V/mil V/mmInsulation ‐ Insulation Shield Interface: 41.76 V/mil 1,644.01 V/mm

Insulation Resistance: 5,927.7 1,086.8Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault38,628 30,721 25,299AmpsAmps Amps

4,468 3,759 3,26610 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

350 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.630 in

394.5 120.2ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A350‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 1.630 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.072Real

0.043Imag.

Inductice Reactance: 0.042Impedance

0.083 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.235 0.140 0.274

0.139 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.412 0.284 0.500 Ω/kft 1.352 0.932 1.642 Ω/kftZero Seq. Impedance (Earth Only): 0.125 0.727 0.737 Ω/kft 0.411 2.384 2.419 Ω/kft

Electrical Properties ContinuedCable Description: 350 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 401

75% Load Factor: 464 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 1.630 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.072Real

0.048Imag.

Inductice Reactance: 0.048Impedance

0.086 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.235 0.156 0.283

0.157 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.407 0.282 0.495 Ω/kft 1.335 0.926 0.283 Ω/kftZero Seq. Impedance (Earth Only): 0.125 0.716 0.727 Ω/kft 0.411 2.350 2.386 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 400

75% Load Factor: 463 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.077Real

0.082Imag.

Inductice Reactance: 0.083Impedance0.112 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.251 0.251 0.368

0.272 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.412 0.281 0.472 Ω/kft 1.243 0.922 1.547 Ω/kftZero Seq. Impedance (Earth Only): 0.125 0.646 0.658 Ω/kft 0.411 2.120 2.160 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 436

75% Load Factor: 469 AmpsAmps

Installation PropertiesCable Description: 350 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 2800 #### 5600 ####Cable Basket Grip: 2800 #### 5600 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 20 49712xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A350‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:500 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

1,544*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.774 0.789 0.797

0.016 0.022 ‐‐ ‐‐ 0.833 ‐‐

0.330 0.345 0.375 1.480 1.523 1.580

‐‐ 0.005 ‐‐ ‐‐ 1.598 ‐‐

0.024 0.030 0.060 1.530 1.583 1.670

0.100 0.110 0.150 ‐‐ 1.818 ‐‐

Insulation Level100%

Conductor Weight467

Met. Shield Weight117

Cable Weight

Electrical Properties

Cable Description: 500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.037 0.122Rac @ 25°C: 0.038 0.124Rac @ 105°C: 0.049 0.162

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.423 1.388Rac @ 95°C: 0.537 1.763

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.065 0.213µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 40,890 12,463Shunt Capacitive Susceptance: 24.46 80.24

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 486.6 1,596.4mA/kf mA/km

6.78 22.23Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 56.01 V/mil 2,204.97 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 79.26 3,120.56V/mil V/mmInsulation ‐ Insulation Shield Interface: 43.30 V/mil 1,704.77 V/mm

Insulation Resistance: 5,241.1 1,597.5Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault55,136 43,833 36,084AmpsAmps Amps

3,608 3,608 3,60810 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 1.818 in

377.8 115.1ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A500‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 1.818 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.050Real

0.040Imag.

Inductice Reactance: 0.041Impedance

0.064 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.164 0.133 0.211

0.134 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.381 0.258 0.460 Ω/kft 1.249 0.847 1.509 Ω/kftZero Seq. Impedance (Earth Only): 0.103 0.719 0.726 Ω/kft 0.339 2.358 2.382 Ω/kft

Electrical Properties ContinuedCable Description: 500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 489

75% Load Factor: 567 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 1.818 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.050Real

0.046Imag.

Inductice Reactance: 0.046Impedance

0.068 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.165 0.152 0.224

0.152 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.376 0.257 0.455 Ω/kft 1.232 0.842 0.224 Ω/kftZero Seq. Impedance (Earth Only): 0.103 0.707 0.715 Ω/kft 0.339 2.320 2.344 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 487

75% Load Factor: 566 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.055Real

0.078Imag.

Inductice Reactance: 0.079Impedance0.095 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.181 0.181 0.313

0.258 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.381 0.258 0.436 Ω/kft 1.154 0.845 1.430 Ω/kftZero Seq. Impedance (Earth Only): 0.103 0.642 0.650 Ω/kft 0.339 2.107 2.134 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 524

75% Load Factor: 599 AmpsAmps

Installation PropertiesCable Description: 500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 4000 #### 8000 ####Cable Basket Grip: 4000 #### 8000 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 22 55412xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A500‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:750 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

1,934*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 0.949 0.968 0.978

0.020 0.026 ‐‐ ‐‐ 1.020 ‐‐

0.330 0.345 0.375 1.670 1.710 1.770

‐‐ 0.005 ‐‐ ‐‐ 1.785 ‐‐

0.024 0.030 0.060 1.720 1.770 1.860

0.100 0.110 0.150 ‐‐ 2.005 ‐‐

Insulation Level100%

Conductor Weight705

Met. Shield Weight128

Cable Weight

Electrical Properties

Cable Description: 750 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.026 0.084Rac @ 25°C: 0.026 0.087Rac @ 105°C: 0.034 0.113

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.379 1.242Rac @ 95°C: 0.480 1.576

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.076 0.249µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 34,994 10,666Shunt Capacitive Susceptance: 28.58 93.75

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 568.6 1,865.4mA/kf mA/km

7.92 25.98Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 56.42 V/mil 2,221.24 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 75.57 2,975.14V/mil V/mmInsulation ‐ Insulation Shield Interface: 45.01 V/mil 1,772.18 V/mm

Insulation Resistance: 4,487.9 1,367.9Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault82,567 65,618 53,998AmpsAmps Amps

5,435 4,573 3,97310 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

750 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 2.005 in

360.4 109.9ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A750‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 2.005 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.035Real

0.038Imag.

Inductice Reactance: 0.038Impedance

0.052 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.115 0.125 0.170

0.126 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.351 0.226 0.418 Ω/kft 1.153 0.741 1.370 Ω/kftZero Seq. Impedance (Earth Only): 0.088 0.709 0.715 Ω/kft 0.290 2.327 2.345 Ω/kft

Electrical Properties ContinuedCable Description: 750 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 598

75% Load Factor: 698 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 2.005 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.036Real

0.044Imag.

Inductice Reactance: 0.044Impedance

0.057 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.116 0.145 0.186

0.145 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.347 0.225 0.413 Ω/kft 1.138 0.738 0.186 Ω/kftZero Seq. Impedance (Earth Only): 0.088 0.697 0.703 Ω/kft 0.290 2.287 2.306 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 595

75% Load Factor: 696 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.040Real

0.073Imag.

Inductice Reactance: 0.074Impedance0.084 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.132 0.132 0.274

0.243 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.351 0.228 0.399 Ω/kft 1.074 0.747 1.309 Ω/kftZero Seq. Impedance (Earth Only): 0.088 0.638 0.644 Ω/kft 0.289 2.092 2.111 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 630

75% Load Factor: 726 AmpsAmps

Installation PropertiesCable Description: 750 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 6000 #### 12000 ####Cable Basket Grip: 6000 #### 12000 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 24 61112xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A750‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:1000 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

2,290*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 1.095 1.117 1.128

0.024 0.030 ‐‐ ‐‐ 1.177 ‐‐

0.330 0.345 0.375 1.815 1.867 1.920

‐‐ 0.005 ‐‐ ‐‐ 1.942 ‐‐

0.024 0.030 0.060 1.865 1.927 2.010

0.100 0.110 0.150 ‐‐ 2.162 ‐‐

Insulation Level100%

Conductor Weight937

Met. Shield Weight141

Cable Weight

Electrical Properties

Cable Description: 1000 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.019 0.061Rac @ 25°C: 0.020 0.065Rac @ 105°C: 0.025 0.083

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.348 1.141Rac @ 95°C: 0.442 1.449

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.085 0.279µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 31,237 9,521Shunt Capacitive Susceptance: 32.01 105.03

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 637.0 2,089.8mA/kf mA/km

8.87 29.10Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 56.66 V/mil 2,230.63 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 73.33 2,886.94V/mil V/mmInsulation ‐ Insulation Shield Interface: 46.16 V/mil 1,817.45 V/mm

Insulation Resistance: 4,007.4 1,221.5Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault110,011 87,410 71,916AmpsAmps Amps

5,918 4,978 4,32510 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

1000 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 2.162 in

347.7 106.0ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1000‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 2.162 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.026Real

0.037Imag.

Inductice Reactance: 0.037Impedance

0.045 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.086 0.120 0.148

0.121 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.330 0.203 0.388 Ω/kft 1.084 0.666 1.272 Ω/kftZero Seq. Impedance (Earth Only): 0.080 0.702 0.707 Ω/kft 0.261 2.304 2.318 Ω/kft

Electrical Properties ContinuedCable Description: 1000 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 705

75% Load Factor: 825 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 2.162 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.027Real

0.042Imag.

Inductice Reactance: 0.042Impedance

0.050 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.088 0.137 0.163

0.138 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.327 0.202 0.384 Ω/kft 1.072 0.664 0.163 Ω/kftZero Seq. Impedance (Earth Only): 0.080 0.692 0.696 Ω/kft 0.261 2.269 2.284 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 698

75% Load Factor: 819 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.031Real

0.070Imag.

Inductice Reactance: 0.071Impedance0.077 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.103 0.103 0.251

0.232 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.330 0.206 0.373 Ω/kft 1.017 0.677 1.222 Ω/kftZero Seq. Impedance (Earth Only): 0.079 0.634 0.639 Ω/kft 0.260 2.081 2.097 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 730

75% Load Factor: 847 AmpsAmps

Installation PropertiesCable Description: 1000 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 8000 #### 16000 ####Cable Basket Grip: 8000 #### 16000 ####

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 26 65912xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1000‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:1250 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

2,799*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 1.225 1.250 1.263

0.024 0.030 ‐‐ ‐‐ 1.310 ‐‐

0.330 0.345 0.375 1.960 2.000 2.065

‐‐ 0.005 ‐‐ ‐‐ 2.075 ‐‐

0.024 0.030 0.060 2.010 2.060 2.155

0.100 0.110 0.150 ‐‐ 2.295 ‐‐

Insulation Level100%

Conductor Weight1,197

Met. Shield Weight148

Cable Weight

Electrical Properties

Cable Description: 1250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.015 0.048Rac @ 25°C: 0.016 0.053Rac @ 105°C: 0.020 0.067

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.329 1.080Rac @ 95°C: 0.417 1.370

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.091 0.299µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 29,094 8,868Shunt Capacitive Susceptance: 34.37 112.77

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 683.9 2,243.6mA/kf mA/km

9.53 31.25Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 56.80 V/mil 2,236.18 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 72.09 2,838.17V/mil V/mmInsulation ‐ Insulation Shield Interface: 46.86 V/mil 1,844.87 V/mm

Insulation Resistance: 3,675.2 1,120.2Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault137,446 109,194 89,825AmpsAmps Amps

6,254 5,261 4,57110 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

1250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 2.295 in

340.1 103.7ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1250‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6/24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 2.295 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.021Real

0.036Imag.

Inductice Reactance: 0.036Impedance

0.042 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.069 0.118 0.137

0.117 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.317 0.189 0.369 Ω/kft 1.040 0.620 1.211 Ω/kftZero Seq. Impedance (Earth Only): 0.074 0.697 0.701 Ω/kft 0.244 2.288 2.301 Ω/kft

Electrical Properties ContinuedCable Description: 1250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 794

75% Load Factor: 933 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 2.295 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.022Real

0.041Imag.

Inductice Reactance: 0.041Impedance

0.046 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.072 0.134 0.152

0.135 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.314 0.189 0.366 Ω/kft 1.029 0.618 0.152 Ω/kftZero Seq. Impedance (Earth Only): 0.074 0.687 0.691 Ω/kft 0.244 2.254 2.268 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 784

75% Load Factor: 923 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.026Real

0.068Imag.

Inductice Reactance: 0.069Impedance0.073 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.086 0.086 0.238

0.225 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.317 0.193 0.356 Ω/kft 0.981 0.634 1.168 Ω/kftZero Seq. Impedance (Earth Only): 0.074 0.632 0.636 Ω/kft 0.242 2.074 2.088 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 811

75% Load Factor: 945 AmpsAmps

Installation PropertiesCable Description: 1250 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 10000 #### 20000 89Cable Basket Grip: 10000 #### 20000 89

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 28 70012xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1250‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6/24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

A: Conductor:1500 kcmil Class B Compressed Stranded Filled AL ConductorB: Conductor Shield:Semiconducting Thermoset PolymerC: Insulation:Tree Retardant Crosslinked Polyethylene

E: Metallic Shield:1 x 1.5" x 0.005" Bare Copper Tape

D: Insulation Shield:Semiconducting Thermoset Polymer

F: Jacket:Overlaying Polyvinyl Chloride with 3 Red Extruded StripesSingle Conductor Finished Cable Nominal Weights:  lbs/kft*

3,140*Nominal values are subject to manufacturing tolerances:

Component DescriptionThickness Diameter

Min. Min.Nom. Nom.Max. Max.

Physical Properties

‐‐ ‐‐ ‐‐ 1.343 1.370 1.384

0.024 0.030 ‐‐ ‐‐ 1.430 ‐‐

0.330 0.345 0.375 2.100 2.120 2.205

‐‐ 0.005 ‐‐ ‐‐ 2.195 ‐‐

0.024 0.030 0.060 2.150 2.180 2.295

0.100 0.110 0.150 ‐‐ 2.415 ‐‐

Insulation Level100%

Conductor Weight1,411

Met. Shield Weight157

Cable Weight

Electrical Properties

Cable Description: 1500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Conductor Resistance:Rdc @ 25°C: 0.012 0.040Rac @ 25°C: 0.014 0.046Rac @ 105°C: 0.018 0.057

Ω/kftΩ/kftΩ/kft

Ω/kmΩ/kmΩ/km

Shield Resistance:Rac @ 25°C: 0.308 1.009Rac @ 95°C: 0.391 1.281

Ω/kftΩ/kft

Ω/kmΩ/km

Capacitance: 0.100 0.327µF/kft µF/km

Shunt Capacitive Reactance/Susceptance:

Shunt Capacitive Reactance: 26,647 8,122Shunt Capacitive Susceptance: 37.53 123.12

Ω‐kftµS/kft

Ω‐kmµS/km

Charging Current: 746.7 2,449.7mA/kf mA/km

10.40 34.12Dielectric Losses (Per Phase): W/kft W/km

Electrical Stress:Insulation Average Stress ‐ V/mil: 56.93 V/mil 2,241.34 V/mm

Conductor Shield ‐ Insulation Interface Maximum: 70.71 2,783.73V/mil V/mmInsulation ‐ Insulation Shield Interface: 47.65 V/mil 1,875.85 V/mm

Insulation Resistance: 3,420.0 1,042.4Ω‐kft Ω‐km

Velocity of Propagation:

Conductor Fault164,872 130,969 107,726AmpsAmps Amps

6,695 5,632 4,89310 Cycles 16 Cycles 24 Cycles

AmpsAmps Amps

Current @ 250°C:

Shield FaultCurrent @ 200°C:

1500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Input Parameters:

Electrical Properties Based onNormal Operating Temp: 105

Dielectric Constant: 2.32IR Constant @ 60°F: 20000

Earth Resistivity: 100

°C

Ω‐m

Dissipation Factor: 0.07%Voltage (Line to Ground: 19.94 kVConductor Spacing (S): 2.415 in

330.8 100.8ft/µs m/µs

10 Cycles 16 Cycles 24 Cycles

ABC

DEF

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1500‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com

S

TrefoilArrangement

Conductor Spacing (S): 2.415 in

Three‐Phase Trefoil Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.018Real

0.035Imag.

Inductice Reactance: 0.035Impedance

0.039 Ω/kft

Ω/kfReal Imag. Impedance

Ω/kft0.060 0.114 0.129

0.114 Ω/km

Zero Seq. Impedance (Earth  Met. Shield) 0.304 0.173 0.349 Ω/kft 0.996 0.567 1.146 Ω/kftZero Seq. Impedance (Earth Only): 0.072 0.692 0.696 Ω/kft 0.235 2.270 2.283 Ω/kft

Electrical Properties ContinuedCable Description: 1500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Trefoil Conductor Ampacity @ 105°C: 100% Load Factor: 866

75% Load Factor: 1020 AmpsAmps

S S

2S

Flat AdjacentArrangement

Conductor Spacing (S): 2.415 in

Three‐Phase Flat Adjacent Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.019Real

0.040Imag.

Inductice Reactance: 0.040Impedance

0.044 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.063 0.130 0.144

0.130 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.301 0.172 0.347 Ω/kft 0.986 0.566 0.144 Ω/kftZero Seq. Impedance (Earth Only): 0.072 0.682 0.686 Ω/kft 0.235 2.238 2.251 Ω/kft

Flat Adjacentl Conductor Ampacity @ 105°C: 100% Load Factor: 851

75% Load Factor: 1006 AmpsAmps

S S

2S

Flat SpacedArrangement

Conductor Spacing (S): 7.5 in

Three‐Phase Flat Spaced Reactance/Impedance:

Pos/Neg Seq. Impedance (Met. Shield): 0.023Real

0.065Imag.

Inductice Reactance: 0.066Impedance0.069 Ω/kft

Ω/kftReal Imag. Impedance

Ω/kft0.076 0.076 0.227

0.217 Ω/km

Zero Seq. Impedance (Earth+Met. Shield): 0.304 0.178 0.338 Ω/kft 0.945 0.583 1.110 Ω/kftZero Seq. Impedance (Earth Only): 0.071 0.630 0.634 Ω/kft 0.233 2.065 2.160 Ω/kft

Flat Spaced Conductor Ampacity @ 105°C: 100% Load Factor: 874

75% Load Factor: 1024 AmpsAmps

Installation PropertiesCable Description: 1500 KCMIL FILLED STRANDED AL ‐ 0.345" TRXLPE ‐ 1/0.005" CU TAPE SHIELD ‐ PVC JACKET POWERGUARD 35KV 100%

Maximum Pulling Tension

Single Conductor

Conductor Pulling Eye/Bolt: 12000 #### 24000 ####Cable Basket Grip: 10000 #### 20000 89

lbslbs

kN lbs kN

3x1/C Parallel

kN lbs kN

Maximum Sidewall Bearing Pressure:

1500 22lb/ft of bend radius kN/m of bend radius

Maximum Bending Radius:

NEC Applications: 29 73612xO.D. inches mm

Specification / Standard:AEIC CS8, ICEA S‐97‐682, ICEA T‐31‐610,  MV 105 UL 1072

Item No:A1500‐01MV35GT10501

Prepared By:J. DORFMAN

Date:6 /24/2013

Dimensions and weights not designated minimum or maximum are nominal and subject to manufacturing tolerances.Spec No: 314American Wire Group

Tel: 954‐455‐3050 www.buyawg.com