RT0 RF WIRELESS ROOM THERMOSTAT AND RECEIVER

Pack contains ....................................................................................1Installation - Receiver .......................................................................1 Mounting of wall mouting plate .......................................................................1 Wiring ...................................................................................................................1 Mounting of the receiver ...................................................................................2

Installation - Thermostat ....................................................................2 Installing batteries ...............................................................................................2 Mounting of thermostat .....................................................................................2

Pairing procedure..............................................................................3Troubleshooting .................................................................................3

...................................................................3

RTE0RFA NEO ENG FP V04 29 05 2015

WIRING

1

INSTALLATION INSTRUCTIONS

All wiring must be in accordance with IEE regulations. This product is for

Screw AnchorAA Batteries (LR6)

Thermostat Receiver Thermostat table stand

Screws

MOUNTING OF WALL MOUTING PLATE

1- Unscrew the 2 screws under the 2-

are not sure how to install this thermostat consult either with a

PACK CONTAINS

INSTALLATION - RECEIVER

N = Neutral L = Live 1 = Not used 2 = Normally closed 3 = Common

2N L 1 43

3-

2

• On the wall

MOUNTING OF THERMOSTAT

1- Unscrew the 2 screws under the 2-

1- Remove the batteries cover 2- -

3-

INSTALLING BATTERIES

INSTALLATION - THERMOSTAT

MOUNTING OF THE RECEIVER1- 2-

• On the table stand

3-

5- Secure the thermostat by

1-

2

1

2- Fold the stand and lock it into

30° 37°

3

PAIRING PROCEDURE

TECHNICAL SPECIFICATIONS

Receiver:

Signal sending:

Standards:

Environment :

N.B.:

The

Transmitter ReceiverR&TTE EMC RoHS R&TTE-EMC RoHS

EN62311 EN300440-1 EN300440-2

EN60730-1 EN62479 EN300440-1

EN300440-2

NB:

Important:

-

Do not use rechargeable batteries.

The heating does not come on or does not go off.

section on- Check that the radio communication works between the thermostat

TROUBLESHOOTING

Thermostat RF icon and re-3- Thermostat RF icon and recei-

Override RF TestOverride RF Test

-

2- 5 seconds the RF test button

1- 5 seconds the RF test button on the

5 sec

Override RF Test

Override RF Test

5 sec

2- The receiver does not recognize transmitter’s code.

The radio link between the thermostat and the receiver is lost.

- Check that the radio communication works between the thermostat

- Check that the radio communication works between the thermostat

-

Overview ..................................................................................................1Controls and display ...............................................................................1Settings .....................................................................................................1 Initial power up ..................................................................................................1 Pairing procedure ..............................................................................................2

Operating .................................................................................................1 Temperatures setting .........................................................................................1 Factory settings ...................................................................................................2

Troubleshooting .......................................................................................2 .........................................................................2

What is a room thermostat......................................................................2

RTE0RFa NEO ENG FP V02 29 05 2015

RT0 RF WIRELESS ROOM THERMOSTAT AND RECEIVER

1

OPERATING INSTRUCTIONS

1- To start: insert the two AA bat-teries provided into the battery compartment.

the LCD screen as shown for two seconds.

2- show:

- The ambient temperature (°C)

- The icon heating is turned ON.

- The setpoint temperature (°C)

Note: appears on the device.

• Thermostat

have created and designed our products

It is this ease of operation that is intended

energy and money.

OVERVIEW

CONTROLS AND DISPLAY

INITIAL POWER UP

SETTINGS

• LCD Display

C

CMeasured room

temperature

Pairing icon

Low battery icon

Frost protection icon

icon

Temperature setpoint

C

C

Batteries compartment

Reset button

C

RF test button

PAIRING PROCEDURE

The thermostat and the receiver are not bonded together at the facto-ry.

2- for 5 seconds the RF test button on the thermostat. Pairing icon

1- 5 seconds the RF test button on the

5 sec

Override RF Test

Override RF Test

5 sec

C

C

2

Regi

ster

ed tr

adem

arks

- A

ll rig

hts r

eser

ved

NEOMITIS® LIMITED - 4th Floor, Lincoln House, 300 High Holborn, London WC1V 7JH Registered in England and Wales No: 9543404

Tel: +44 (0) 2071 250 236 - Fax: +44 (0) 2071 250 267 - E-mail: contact_uk@neomitis.com

Creating innovative solutions for ambient comfort

www.neomitis.com

FACTORY SETTINGS

than 3 seconds using the tip of a pen.

restored.

Settings Factory settingsSet temperature 20°C

The boiler is not heating:

off. If no increase set temperature.- Check the position of the batteries. Remove them for 30 seconds and

Nothing in the display:- Check the position of the batteries. Remove them for 30 seconds and

TROUBLESHOOTING

4- Thermostat RF icon and re-3- Thermostat RF icon and recei-

Override RF Test

the heating system on and off as necessary. It works by sensing the air temperature, switching on the heating when the air temperature

and switching it off once this set temperature has been reached.Turning a room thermostat to a hi-

-

-

energy and cost you more money.

-

WHAT IS A ROOM THERMOSTAT

-

TECHNICAL SPECIFICATIONS

The desired temperature can be set.1- -

-ture.

TEMPERATURES SETTING

OPERATING

C

C

Override RF Test

The room temperature is not high enough, the boiler is not providing enough heat:- Check the active desired temperature and increase it if need be (see

page 1).You made a mistake while setting:

settings” section (see page 2)have made.

The system is not heating but is on:- If

If the problem persists, then contact your installer.