Personality Masks

Carnival masks

AFRICAN MASKS

Balinese Masks

Pablo Picasso’s depiction of the face

Mask building process

1.Building the mold -A mold is a structure that is covered with a malleable sculpture medium, This medium is later removed and retains the shape of the mold.

The mold will be made from cardboard, newspaper and masking tape. Start by cutting out the basic shape of your mask from cardboard. Also cut out several long strips of

cardboard about an inch wide.Cut slits into the surface of the long strips of cardboard. Do not cut all the way through

the cardboard. This will help the cardboard bend smoothly. Bend these strips around the basic shape of the face and tape onto the larger shape. Now you will have a raised face

shape.On top of this basic structure start taping crumbled up pieces of newspaper. These

pieces of newspaper should be in the shape of the features of the mask. Build up the newspaper and tape until you have a solid and detailed 3D form. This is your mold.

2.Plaster -Cut plaster gauze into small strips. Dip these strips into warm water and completely cover the outside area of the mold. Repeat this process after the first layer is

dry. Let dry overnight and then remove mask from the mold. Plaster should be in the shape of the mold. Place a layer of gauze inside the mask and along the edges. Discard the mold.

3.Finishing touches -After the plaster is dry add small amounts of self hardening (celluclay) clay. This should be for details like hair, wrinkles, texture, etc. Blend and

smooth well so it will adhere to the plaster, let celluclay dry overnight. Also think about

adding any found objects that make conceptual or visual sense. Paint mask.

What Supplies Do I Need To Make The Mold?

• Pencil And Eraser• Ruler• Scissors• Xacto Knife• Stiff Cardboard • Masking Tape

I. Building A Mold

Step 1Using Resources, Draw A Preliminary Sketch In Frontal And Profile Views

I. Building A Mold

Step 2Referring To The Frontal View Of Your Preliminary Sketch, Draw The Outline Of Your Form On A Piece Of Cardboard

I. Building A Mold

Step 3• Measure And Cut

One-Inch Strips Of Cardboard

• Score Strips, Being Careful Not To Cut Through The Cardboard

I. Building A Mold

Step 4• Bend Strips Along

Scoring Lines And Fit Them Perpendicularly Along The Edges

• Tape Strips Securely To The Form

I. Building A Mold

Step 5• The Mold Is Now A

Raised Form

• Reinforce Any Loose Sections With Tape

I. Building A Mold

Step 6• Draw and Cut Out

Shapes For Areas That Will Project

• Tape Shapes To The Form

I. Building A Mold

Step 7• Build Up The Form

By Taping Down Crumpled Newspaper

• This Process Will Require Using Many Layers

I. Building A Mold

Step 8Building The Form Requires Patience As Each Layer Slowly Creates A Three-Dimensional Form

I. Building A Mold

Step 9Continue To Build Up Areas With Newspaper And Tape, Evaluating The Total Form From All Angles

I. Building A MoldFINISHED MOLD

What Supplies Do I Need To Create A Mask?

• Bucket Container• Plaster gauze cut into

small strips• Scissors• Paper to cover table

II. Creating A Mask

Step 1• Dip First Strip Into

water And Apply To Mold

• Continue to Dip And Apply Strips Until The Mold Is Covered Completely

II. Creating A Mask

Step 2• Let plaster dry

thoroughly• Apply another coat of

plaster to fill in thin areas.

II. Creating A Mask

Step 3• Carefully Remove All

Pieces Of The Mold From Mask

• Don’t Panic If Areas Tear – You Can Patch Them

II. Creating A Mask

Step 4• Apply One Coat Of

plaster Inside The Mask, Including The Inside Edge

• Patch Areas That Are Torn Or Too Thin

• Your Mask Is Now Ready For Phase III, Which Is Painting And Embellishing