Implantology

Perfect results effortlessly

Precision and working efficiently with first-class materials is in demand.For the benefit of the patient as well as advantageous for dentists and dental technicians.

1 AFFINIS

AFFINIS®

Innovative surface affinity. AFFINIS has set a new standard due to its fast wetting of mixed material to moist tooth structure and gingival tissue.

Superior flow properties. Due to the structural properties of its surfactant system, AFFINIS provides a very low flow limit (self-contouring consistency). With flow properties similar to hydrocolloids, it flows very well without pressure (tray material) into all critical areas. At the same time, the mixed material delivers sufficient stability and does not drip from the preparation.

Screwing in the impression post for a closed impression.

Checking the location of the impression post.

Brushing the President impression tray with Coltène Adhesive.

Repositioning caps set on the impression post.

The ideally harmonised working and setting time of AFFINIS enables you to work safely and efficiently. After positioning the impression tray, gently press the tray and hold it in place during the short setting time. The impression can be easily removed due to its high tear strength to ensure that all details are captured. An impression with perfect reproduction of the marginal contours and a dimensional change of up to 0.2 % provides the ideal starting situation for the dental technician to produce accurate restorations.

Innovative surface affinity and flow properties lead to perfect results.

Thanks to the innovative surface affinity and superior flow properties of the AFFINIS wash materials (light and regular body), which correspond to the properties of a hydrocolloid, air voids which can result in distortions in the restoration area can be virtually eliminated.

AFFINIS light body AFFINIS regular body

2

2 AFFINIS MonoBody

AFFINIS® MonoBody

≤60s≤60s ≥2min30s

Filling the impression tray with AFFINIS MonoBody.

Syringing around the impression posts using AFFINIS MonoBody.

Positioning of the tray in the mouth. The tray is then pressed into place for 2-3 seconds and held until the material is completely set.

Carefully remove the impression from the mouth.

AFFINIS 360 MonoBody is available in both self-activating 360 ml foil bags for dynamic mixing machines and in 75 ml Automix cartridges for the hand dispenser. The AFFINIS MonoBody single-phase impression material has been developed as a tray and syringe material. It has excellent wetting properties in a moist environment. The AFFINIS surface affinity is comparable with the hydrophilic properties of a polyether or hydrocolloid.

•Snapsetpreventsinaccuraciesduetomovement.•Outstandingthixotropy–stable,flowsunder

pressure •Neutraltaste•Superiorflexibility–easyremoval,alsofrom

the model •Dimensionallystableevenafterdisinfection

The first single-phase impression material with an innovative AFFINIS surface wetting system for perfect impressions in a moist environment.

IMPORTANT: Check the setting of the impression, also intraorally, before removing from the mouth. Higher temperatures will accelerate the setting process, while lower temperatures will slow this down.

Impressively free of voids.

3

3 AFFINIS PreciOuS

AFFINIS®PreciOuS

unscrewingtheimpressionpost.

Screwing in the gingival formers which correspond to the dimensions of the final restoration.

Screwed in gingival former. Introduction of the temporary clamp.

AFFiNiS PreciOuS delivers excellent detail readability. The unique Silver and Goldpigmentation significantly reduces the light scatter and improves the visual perception of detail.

AFFiNiS PreciOuS polyvinylsiloxane (PVS) wash materialshave a contact angle of only 10 degrees. Its superior flow properties enable the impression material to easily register all critical surface details of the preparation, even in a moist environment.

AFFINIS PRECIOUS has been developed to achieve highly accurate results in the mouth and in the laboratory. Immediate wetting of the impression surface enables the plaster to flow more easily in order to produce more accurate stone models.

Superior flow properties where it counts -in the mouth ...

Consistency of AFFINIS PreciOuS.

A perfect impression with AFFINIS PreciOuSregularbodyandAFFiNiSheavy body.

TIP: For a longer working time, the material can be placed in the refrigerator before use.IMPORTANT: To guarantee a perfect bond between both materials when a putty wash impression is taken, the first impression (heavy body, Putty or MonoBody) must be cleaned carefully using lukewarm water, and dried.

AFFINIS PRECIOUS light body AFFINIS PRECIOUS regular body

4

4 Cool Temp NATurAL

Cool Temp® NATurAL

≤35s 30-40s

≥4min30s

The low polymerization temperature prevents irritation to the pulp and avoids any discomfort to your patient. Your patient can lean back, relax and remain cool thanks to a simple and quickfabricationofthetemporaryrestoration.

Thanks to its optimal elastic phase, Cool Temp NATURAL can be removed from the mouth even after a very short oral setting time. The result is an accurate temporary restoration that can be finished and polished without difficulty.

TIP: To simplify removal of cool Temp NATurAL, the preparation can becoated with Coltène Separator before application.SIMPLE AND FAST REPAIRS: Synergy Flow is ideal for repairing small defects and modifying crown margins.

IMPORTANT: coolTempNATurALcanbeusedasatemporaryrestorationforimplant treatments, if an abutment is screwed onto the suprastructure.

Temporary crown and bridge material

Filling the putty matrix with coolTempNATurALforthe temporary restoration.

Insertion of the filled putty matrix into the mouth.

After a short oral setting time,coolTempNATurALhas an elastic consistency which allows easy removal from the mouth with the putty matrix.

Oncethetemporaryrestoration has cured completely, it can be finished and polished without any difficulty.

Cementing the Cool Temp temporary restoration with TempoSiL.

EXCELLENT ESTHETICS•3fluorescentVitaTM* colours

USER FRIENDLY •Lowshrinkage=bettermarginaladaptation•Verygoodpolishingproperties

COOL POLYMERIZATION TEMPERATURE •Lowtemperature=noharm/irritationtothepulp

*Vita™isnotatrademarkofcoltène/Whaledent5

5 JeTBLue BITe

JeTBLue® BITe

≤30s ≥40s

Withthenewsmooth,whippedcreamconsistencyofJeTBLueBiTe,thepatientcanoc-clude naturally without feeling any resistance. The material is applied directly from the car-tridge using a special spreader tip. The very brief, patient-friendly oral setting time ensures foraquickbitesituation.Afterthebiteregistrationhascured,JeTBLueBiTehasahighend hardness of 89 Shore A.

Excellent handling as well as fast accurate setting.

ApplicationofJeTBLueBITe on the lower, fourth quadrant.

Thanks to its whipped cream consistency, the patient can occlude comfortably without resistance.

The oral setting time is only 40 s.

AfterJeTBLueBiTehasset,the bite registration can be removed without leaving any residue.

•Staysexactlywhereyouwantit•Nobiteresistance,norebound•Highendhardnessandstillflexibleforeasy

trimming •Pickyouridealspeed: Fast 30 s working time 40 s oral setting time Superfast 20 s working time 30 s oral setting time

Bite registration material

IMPORTANT: After setting and removal of the material from the mouth, all gingival contacts and undercuts should be removed using a sharp knife or bur. This prevents rebounding of the models when they are set up in the articulator.

JeTBLueBiTeisatrademarkofcoltène/WhaledentintheuSA.JeTBLueisaninternationallyregisteredtrademarkofcoltène/WhaledentAG(withoutuSA) 6

6 PINDex

PINDex®

Casting the impression with superhard plaster stone model.

AmatrixfortheGi-MASKisproducedusingLabPuttyonthe stone model.

The area of the stone model to bereproducedbyGi-MASKcanbe reduced using a plaster carving knife.

Injection holes and outlet spruesforGi-MASKcanbeproduced using a carving knife in the area of the implants.

The PINDex system offers you plenty of decisive advantages for the fabrication of your model and dies. The impression can be casted trouble-free prior to the placement of pins. The precision pins and sleeves can always be inserted absolutely parallel thanks to accurate drilling, so that easy removal and repositioning of the stumps can be guaranteed. The pins are not guided by the base of the plaster stone model, but rather by the precision sleeves made of plastic or metal. This means that there is no abrasion of the plaster stone model.

Simple, fast and secure placement of the pins thanks to laser technology.

•Brightlaserbeamforaccuratedeterminationofthe drill position

•Bestvisibilityunderalllightconditionsforfatigue-freework

•Laserlightthatissuperiortoconventionallightsources

Model precision without compromise

Placement of PINDex pins with sleeves.

Completed PINDex model with laboratory implants.

Model is directly removed from theAccuTrAcacrylicglassframe.

completedAccuTrAcmodel with laboratory implants.

TIP: Briefly rinsing the impression with a cleansing agent and thorough rinsing afterwards with water will reduce the surface tension and simplify casting.

7

[pInDEX model system] [aCCUtRaC model system]

7 Gi-MASK New Formula

Gi-MASK® New Formula

≤2min ≥7min

Quick and easy fabrication: Gi-MASK Automix NewFormula is automatically mixed and applied directly from the cartridge. Its convenient working time of 2 minutes, as well as its short setting time of 7 minutes enables fast production of the gingival mask.

Flexible and tear-resistant: The gingival mask is exposed to high stresses due to repeated insertion and removal during the production of the restoration. Gi-MASK Automix NewFormula provides ideal elasticity and a high tear strength to enable trouble-free completion of the work.

TheLab-PuttymatrixisisolatedusingGi-MASKuniversal separator.

injectGi-MASKusingthemixing and application tip in the corresponding hole, until the material escapes from the opposite hole.

After the setting time, remove the matrix and separate the retention between the injection holes and the outlet sprues using a scalpel.

Remove excess and distortions using a rotating instrument for silicone at a low speed.

Gi-MASKAutomixNewFormulaisusedforaccuratereproductionofsofttissuestructures.The A-Silicone gingival mask delivers all information for the exact design of suprastructures or frameworks. esthetic colouring of the gingival mask helps you to better assess the clinical situation.

Facilitates perfect esthetics, perfect function and periodontal hygiene in dental restorations.

8

NOTE: Gi-MASKisalsoavailableinac-Siliconehandmix(seeorderinginformation).

TheGi-MASKgingivalmaskcan be easily removed from the master model and repo-sitioned.

The PINDex sleeves are positio-ned onto the glued pins.

The model is cut into segments using the PINDex saw.

The critical requirementsfor the articulation of the model have been fulfilled for precision fabrication of implants.

Gi-MASKAutomixNewFormula can be injected directly into the impression. The laboratory implants are covered approx. 5 mm high using the application tip.

PLACE MARKERS: Place a thin wax layer around the visible segment of the impression post, up to the screwed-on analogue (place marker). The same thing can also be done on places inside the impression where the bridge units will be applied later. This saves you the time involved to grind or cut the gingival mask.

Easy to grind and cut. Due to its optimum stability, the gingival mask can be accurately cut using the silicone trimmer bur included in the starter kit or with a scalpel.

9

8 ParaCem universalDc

ParaCem®universalDc

Buccal view of the precise implant crowns.

unscrewingandremovingthegingival former.

Screwing in the abutments produced by the dental technician.

ParaBond Non-Rinse Conditioner is massaged and air-blown. Application of the mixed ParaBond Adhesive A and B afterwards.

ParacemuniversalDcisadualcureuniversalcompositeresincementforcementationofindirectrestorations,includingcrowns,bridges,inlays/onlays,veneersandrootcanalposts(allmaterialssuchasceramics,metal,composite).ParacemuniversalDcisauser-friendlycement that can also be used as a core build-up material.

SMOOTH THIXOTROPIC CONSISTENCY•easyhandling•easyremovalofexcessmaterial•canbeusedforcorebuild-upsmaterial VITA™ SHADES – SIMPLE SHADE SELECTION HIGH ADHESIVE STRENGTH – DURABLE RESTORATION

Highest performance in esthetics, handling and retention. Highshearbondstrength–durablerestoration.ParacemuniversalDcprovidesexcellentretentiontoenameland dentin, ensuring for long lasting restorations. An excellent bond is achieved using ParaBond® Non-Rinse Conditioner with ParaBond Adhesive. Its dual cure properties provide you the choice to light cure for on command cementation, and also ensures for a complete cure via chemical cure where light may not penetrate.

A cement that leaves no wishes unfulfilled.

10

Dose and thoroughly mix ParaCem base and catalyst usinga1:1ratio.

ParacemuniversalDcisap-plied using a brush on to the inside of the restoration.

Checking the contact points and necessary polishing.

Final situation from the buccal view.

post and core.High mechanical strength for core build-ups.

Crowns and bridges.easy removal of excess material due to its ideal thixotropic consistency.

ParacemuniversalDchasbeendevelopedforuniversalapplications.itssmoothconsistencyandexcellent handling properties simplify its use and the removal of excess material.

11

1

2

6530 AFFINIS putty soft Base and Catalyst each 300 ml6531 AFFINIS fast putty soft Base and Catalyst each 300 ml 6535 AFFINIS putty super soft Base and Catalyst each 300 ml

6520 AFFINIS heavy body 75 ml Cartridge 2 x 75 ml MT/TurquOiSe/cLeAr/WHiTe/68/S* 8 pc

6620 AFFINIS fast heavy body 75 ml Cartridge 2 x 75 ml MT/TurquOiSe/cLeAr/WHiTe/68/S* 8 pc

6501 AFFINIS light body 50 ml Cartridge 2 x 50 ml MT/yeLLOW/cLeAr/WHiTe/69/S* 12 pc

6601 AFFINIS fast light body 50 ml Cartridge 2 x 50 ml MT/yeLLOW/cLeAr/WHiTe/69/S* 12 pc 6511 AFFINIS regular body 50 ml Cartridge 2 x 50 ml MT/yeLLOW/cLeAr/WHiTe/69/S* 12 pc

6611 AFFINIS fast regular body 50 ml Cartridge 2 x 50 ml MT/yeLLOW/cLeAr/WHiTe/69/S* 12 pc

ACCESSORIES 50/75 SYSTEM6900 Dispenser50/75ml 1 pc6550 MT/yeLLOW/cLeAr/WHiTe/69/S* 40 pc6552 MT/TurquOiSe/cLeAr/WHiTe/68/S* 40 pc6555 OralTips,yellow 100 pc

PUTTY

SYSTEM 50/75

SYSTEM 50/75

SYSTEM 360

MICROSYSTEMTM

6487 AFFINIS System 360 heavy body Refill pack Base 2 x 300 ml Refill pack Catalyst 2 x 62 ml

6485 AFFINIS System 360 heavy body Starter Kit Base 1 x 300 ml Catalyst 1 x 62 ml Supporting cartridge 1 pc MT/GreeN/cLeAr/WHiTe/50/S* 10 pc

ACCESSORIES SYSTEM 3606160 Supporting cartridge 1 pc6161 MT/GreeN/cLeAr/WHiTe/50/S* 40 pc

6500 AFFINIS light body microSystem™ microSystem™cartridge 4 x 25 ml MT/GreeN/GreeN/WHiTe/70/S* 20 pc OralTips 20 pc

6600 AFFINIS fast light body microSystem™ microSystem™cartridge 4 x 25 ml MT/GreeN/GreeN/WHiTe/70/S* 20 pc OralTips 20 pc

6510 AFFINIS regular body microSystem™ microSystem™cartridge 4 x 25 ml MT/cLeAr/cLeAr/WHiTe/70/S* 20 pc OralTips 20 pc

6610 AFFINIS fast regular body microSystem™ microSystem™cartridge 4 x 25 ml MT/cLeAr/cLeAr/WHiTe/70/S* 20 pc OralTips 20 pc

ACCESSORIES MICROSYSTEM™6270 microSystem™DispenserMKii 1 pc6214 MT/cLeAr/cLeAr/WHiTe/70/S* 40 pc6202 MT/GreeN/GreeN/WHiTe/70/S* 40 pc6210 OralTips 100 pc

6547 AFFINIS MonoBody 75 ml Cartridge 2 x 75 ml MT/TurquOiSe/cLeAr/WHiTe/68/S* 8 pc

ACCESSORIES 50/75 SYSTEM6900 Dispenser50/75ml 1 pc6550 MT/yeLLOW/cLeAr/WHiTe/69/S* 40 pc6552 MT/TurquOiSe/cLeAr/WHiTe/68/S* 40 pc6555 OralTips,yellow 100 pc

6482 AFFINIS System 360 MonoBody Refill pack Base 2 x 300 ml Refill pack Catalyst 2 x 62 ml

6480 AFFINIS System 360 MonoBody Starter Kit Base 300 ml Catalyst 62 ml Supporting cartridge 1 pc MT/GreeN/cLeAr/WHiTe/50/S* 10 pc

ACCESSORIES SYSTEM 3606160 Supporting cartridge 1 pc6161 MT/GreeN/cLeAr/WHiTe/50/S* 40 pc

12

SYSTEM 360

*MT=MixiNGTiPS,S=STrAiGHT

Page2:AFFiNiS

Page3:AFFiNiSMonoBody

3

4

MICROSYSTEMTM

6779 AFFINIS PRECIOUS light body microSystem™ 25mlmicroSystem™cartridge 4 pc MT/GreeN/GreeN/WHiTe/70/S* 20 pc OralTips 20 pc

6780 AFFINIS PRECIOUS regular body microSystem™ 25mlmicroSystem™cartridge 4 pc MT/cLeAr/cLeAr/WHiTe/70/S* 20 pc OralTips 20 pc

ACCESSORIES MICROSYSTEM™6270 microSystem™DispenserMKii 1 pc6214 MT/cLeAr/cLeAr/WHiTe/70/S* 40 pc6215 MT/cLeAr/cLeAr/WHiTe/70/S* 100 pc6202 MT/GreeN/GreeN/WHiTe/70/S* 40 pc6205 MT/GreeN/GreeN/WHiTe/70/S* 100 pc6210 OralTips 100 pc

6775 AFFINIS PRECIOUS light body 50 ml 50 ml cartridge 2 pc MT/yeLLOW/cLeAr/WHiTe/69/S* 12 pc

6776 AFFINIS PRECIOUS regular body 50 ml 50 ml cartridge 2 pc MT/yeLLOW/cLeAr/WHiTe/69/S* 12 pc ACCESSORIES 50/75 SYSTEM6900 Dispenser50/75ml 1 pc6550 MT/yeLLOW/cLeAr/WHiTe/69/S* 40 pc6555 OralTips,yellow 100 pc

5815 Cool Temp Natural A1 Single Pack - 50ml Cool Temp Natural cartridge A1 1 x 50 ml MT/BLue/cLeAr/WHiTe/77/P* 10 pc

5805 Cool Temp Natural A2 Single Pack - 50ml Cool Temp Natural cartridge A2 1 x 50 ml MT/BLue/cLeAr/WHiTe/77/P* 10 pc

5810 Cool Temp Natural A3.5 Single Pack - 50ml Cool Temp Natural cartridge A3.5 1 x 50 ml MT/BLue/cLeAr/WHiTe/77/P* 10 pc

5820 Cool Temp Natural Automix 5ml A1 Refill 10ml Cool Temp Natural Automix syringe A1 2 x 5 ml MT/BrOWN/cLeAr/reD/50/P* 8 pc

5824 Cool Temp Natural Automix 5ml A2 Refill 10ml Cool Temp Natural Automix syringe A2 2 x 5 ml MT/BrOWN/cLeAr/reD/50/P* 8 pc

5825 Cool Temp Natural Automix 5ml A3.5 Refill 10ml Cool Temp Natural Automix syringe A3.5 2 x 5 ml MT/BrOWN/cLeAr/reD/50/P* 8 pc

ACCESSORIES6900 Dispenser50/75ml 1 pc7774 MT/BLue/cLeAr/WHiTe/77/P* 40 pc6748 MT/BrOWN/cLeAr/reD/50/P* 40 pc

13

SYSTEM 50

*MT=MixiNGTiPS,S=STrAiGHT

Page4:AFFiNiS PreciOuS

Page5:coolTempNATurAL

5

6

6491 JET BLUE BITE fast 50ml cartridgeJeTBLueBiTefast 1 x 50 ml MT/PiNK/cLeAr/WHiTe/84/S* 6 pc Spreader Tips 6 pc

6493 JET BLUE BITE superfast 50ml cartridgeJeTBLueBiTesuperfast 1 x 50 ml MT/PiNK/cLeAr/WHiTe/84/S* 6 pc Spreader Tips 6 pc

6492 JET BLUE BITE fast microSystemTM

cartridgeJeTBLueBiTefast 2 x 25 ml MT/cLeAr/cLeAr/WHiTe/70/S* 10 pc Spreader Tips 10 pc

6494 JET BLUE BITE superfast microSystemTM

cartridgeJeTBLueBiTesuperfast 2 x 25 ml MT/cLeAr/cLeAr/WHiTe/70/S* 10 pc Spreader Tips 10 pc

SYSTEM 50/75 ACCESSORIES6900 Dispenser50/75ml 1 pc6551 MT/PiNK/cLeAr/WHiTe/84/S* 40 pc6223 Spreader Tips 100 pc

ACCESSORIES MICROSYSTEM™6270 microSystem™DispenserMKii 1 pc6214 MT/cLeAr/cLeAr/WHiTe/70/S* 40 pc6223 Spreader Tips 100 pc

PINDEX SYSTEM DRILLING UNITSP113LCE PiNDexLASerSystem(230Vceapproved) P113LUK PiNDexLASerSystem(230Vceapproved)withuKPlug

PINDEX SYSTEM ACCESSORIES PX112 Medium Pins and Sleeves (loose fit) 1000 pcPX112T Medium Pins and Sleeves (tight fit) 1000 pc

PX114 LongPinsandSleeves 1000 pc

PX115 Short Pins and Sleeves 1000 pc

PX118 Articulating Pins 100 pcPX119 Carbide Drills 3 pcPX120 Reamer 1 pcPX124 Bulbs 10 pc

PX144 Self Articulating Pins and Sleeves 1000 pcPX145 Self Articulating Pins and Sleeves 100 pcPX145-S Self Articulating Sleeves 1000 pcPX146 Flexible Molds 3 pcPX147 Full Arch Mold 1 pcPX148 FlexibleMolds,right&Left 2 pc

PX153 Dual Pins and Sleeves 1000 pcPX154 Dual Pins and Sleeves 100 pcPX155 TriPLuSPinsandSleeves 1000 pcPX156 LongTriPLuSPinsandSleeves 1000 pc

AT6 STARTER KIT Accu-TrAcacrylicglassframe,brown 6 pcBase plates, white 6 pcArticulation Spacers 6 pcArticulator plates, for magnet 25 pcRecall cards 25 pcNameplates 25 pc

ATR12 REFILL PACK Accu-TrAcacrylicglassframe,brown 12 pcArticulator plates, white 50 pcNameplates 50 pcRecall cards 50 pc

ATN50 TRANSPORTSYSTEM Transport and delivery containers 50 pcNameplates 50 pcPlastic retainers 50 pc

ACCESSORIESATK25 Articulator plates for magnets 25 pc Recall cards 25 pc Nameplates 25 pc ATK300 Articulator plates for magnets 300 pc Recall cards 300 pc Nameplates 300 pcATA20 Lockingarms 20 pc ATT12 Acrylic glass frame, brown 12 pc ATE12 Base plates, white 12 pc ATS1 Articulation spacer, green 1 pc ATS20 Articulation spacer, green 20 pc

14

*MT=MixiNGTiPS,S=STrAiGHT

Page6:JeTBLueBiTe

Page7:PINDex Accu-TrAc

7

8

GI-MASK AUTOMIX NEw FORMULA

8060 Gi-Mask Automix NF Starter Kit Gi-MASKAutomixNFcartridge 2 x 50 ml Gi-MASKuniversalSeparator 50 ml Mixing Tips yellow 12 pc OralTipsyellow 12 pc

8065 GI-MASK Automix NF Refill Kit Gi-MASKAutomixNFcartridge 2 x 50 ml Mixing Tips yellow 12 pc OralTipsyellow 12 pc

ACCESSORIES6550 MT/yeLLOW/cLeAr/WHiTe/69/S* 40 pc6555 OralTipyellow 100 pc6900 Dispenserc/W50/75ml 1 pc8000 Gi-MASKuniversalSeparator 50 ml8075 Trimmer for Silicones 1 pc

8030 Gi-Mask Starter Kit Gi-MaskBase 150 ml Gi-MaskActivator 18 ml Gi-MaskuniversalSeparator 50 ml Application Tips 20 pc Accessories

8035 Gi-Mask Single Pack Gi-MaskBase 150 ml Gi-MaskActivator 18 ml Application Tips 20 pc Accessories

8037 Gi-Mask Refill Pack Gi-MaskBase 150 ml Gi-MaskActivator 18 ml

8036 Gi-Mask Activator 18 ml

7485 ParaCem Universal DC IntroKit ParaCem Base A2 2.5 g ParaCem Base B3 2.5 g ParacemBasewhiteopaque 2.5 g ParaCem Catalyst 3 x 2.5 g ParaBond Adhesive Refill Pack (7486) Accessories

7481 ParaCem Base A2 2.5 g7482 ParaCem Base B3 2.5 g7483 ParaCem Base white opaque 2.5 g7484 ParaCem Catalyst 2.5 g

ParaBond® Adhesive Refill7486 ParaBond Adhesive Refill ParaBond Non-Rinse Conditioner 3 ml ParaBond Adhesive A 3 ml ParaBond Adhesive B 3 ml

15

*MT=MixiNGTiPS,S=STrAiGHT

HANDMIX

AUTOMIX

Page8-9:Gi-MASK

Page10-11:Paracem universalDc

www.coltenewhaledent.com© 2008coltène/WhaledentAG

Coltène/whaledent AGFeldwiesenstrasse 209450Altstätten/SwitzerlandTel. +41 (0)71 757 53 00Fax +41 (0)71 757 53 01office@coltenewhaledent.ch

Coltène/whaledent Ltd.The President Suite-AKendalHouse,BurgessHillVictoriaWayWestSussex,rH159NF/u.K.Tel. +44 (0)1444 235486Fax +44 (0)1444 870640hq@coltenewhaledent.co.uk

Coltène/whaledent Inc.235 Ascot Parkway cuyahogaFalls,Ohio44223/uSATel. +1 330 916 8800Fax +1 330 916 7077productinfo@coltenewhaledent.com92

08u

K-0

9-08

Clinical case:e.T.egloff,Dr.med.dent.,M.S.;D.Zweifel,ZTM,St.Gallen,Switzerland