R

Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / sales@ctcu.com

2020 V1.0

12-1

10101

0101

12

FMUX04A4E1/T1 + 4x GE Fiber Multiplexer

FMUX04A is a fixed design, PDH multiplexer, with 4x E1/T1 plus 4x 10/100/1000Base-T Ethernet switch that provides simultaneous multi-service through dual (1+1) fiber. The fiber optic line is based on 1.25Gbps SFP technology that allows the flexible use of Multimode or Single mode optics and enables support for different wavelengths and distances. The use of bi-directional SFPs maximizes the utilization of fiber optic line and results in saving fiber line costs. The multiplexer can be equipped with optional AC and DC power supplies for redundant operation. With SNMP and Web-based management in the FMUX04A, the administrator can monitor, configure and control both the local and remote device.

Features

Specifications

▪ 4 channels unframed E1/T1 ▪ 4× 10/100/1000Base-TX Ethernet ports ▪ Auto MDI/MDIX ▪ Auto-Negotiation or Force mode ▪ Supports flow control ▪ RS-232 port for system console ▪ One alarm output port, one Order Wire port ▪ Port based VLAN, tag based VLAN & bandwidth control ▪ 2 plug-in SFP slot for optical SFP module ▪ Forward 9K byte packets on Ethernet port ▪ 1+1 fiber protection, less than 50ms

▪ One clear channel RS232 up to 250Kbps(Async) ▪ Supports Digital Diagnostics Monitoring Interface (DDMI) ▪ AIS on signal loss on E1/T1 and fiber port ▪ Loopback test on E1/T1, RS-232, fiber ports ▪ Supports Dying Gasp ▪ Telnet and web based remote configuration ▪ SNMP management ▪ Supports local or remote In-band management ▪ Supports On-Line F/W upgrade (local or remote) by the SNMP manager

E1/T1 Framing: Unframed (transparent)Bit Rate: E1:2.048 Mb/s , T1: 1.544Mb/sLine Code: E1:AMI/HDB3, T1: AMI/B8ZSLine Impedance:E1: Unbalanced 75 ohms (BNC)E1: Balanced 120 ohms (RJ-45) T1: Balanced 120 ohms (RJ-45)Receiver sensitivity: Short haulJitter Performance: According to ITU-T G.823Standard: ITU-T G.644, G.703, G.704, G.706 and G.732Interface Connectors: RJ-45, BNCTest Loops: LLB (Local Loop Back)

RLB (Remote Loop Back) RRLB (Request Remote Loop Back)

OpticalInterface

Bandwidth in optical Line: 1000 MbpsOptical Connector: LC (SFP module)Distance: 20/40/80 Km

OpticalInterface

Optical Wavelength: 1310nm, 1550nm, WDM Tx1310/Rx1550nm (Type A), WDM Tx1550/Rx1310nm (Type B)

Ethernet Interface Type: 100/1000Base-TConnector: 4x RJ-45Standard: IEEE 802.3, 802.3u, 802.3abDuplex modes: full/half

Indication FX1 Link, FX2 link , E1/T1 Mode/Link/Loopback test,Order wire phone indicator , LAN Link/Speed

Power Input AC : 100~240VAC, DC : 18-75 VDCDimensions 248 × 215 × 43mm (D × W × H)Operating 0 ~ 50°C (Operating) Temperature -10 ~ 20°C (Storage)Humidity 10 ~ 90% non-condensingCertifications CE, FCC, RoHS compliantMTBF 75,000 hrs

Application

SmartView

FMUX04A

OrderWire

4E1/T14E1/T1

SDHADM SDHADMOrderWire

PBX

LAN

RS232 clearchannel

RS232 clearchannel

GbE EthernetLAN

GbE EthernetFMUX04A

4E1/T1+GbE over fiber p to p connection Application

Ordering InformationModel Name Description

FMUX04A -AC Standalone FOM with built-in AC PowerFMUX04A -DC Standalone FOM with built-in DC PowerFMUX04A -AD Standalone FOM with built-in AD(AC+DC) Power

4E1/T1 Fiber Multiplexer FM

UX04A

4E1/T1 Fiber Multiplexer

SNMP option only required in one unit of paired linkNote:

10101

0101

R

Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / sales@ctcu.com2020 V1.0

12-2

12

FMUX1001

FMUX101Modularized 16E1/T1 + 4x GbE ManagedFiber Multiplexer

Modularized 16E1/T1 + 4x FE ManagedFiber Multiplexer

The FMUX1001/FMUX101 is a 1U, 19" rack mountable, PDH fiber optic multiplexer that transmits up to 16 channels plus a 10/100/1000Base-T (FMUX1001) / 10/100Base-TX (FMUX101) Ethernet channel over a single fiber optic link. The FMUX1001/FMUX101 chassis supports redundant power and hot swappable design. The AC supplies operate from 100~240VAC while DC supplies operate from 18~60VDC. From the rear of the chassis, one to four hot swappable quad E1 or T1 line cards, serial data communications (V.35, X.21, RS-530) or FXO/FXS voice cards are supported. The standard FMUX1001 configuration may be viewed or set via the front panel LCD/menu keys, serial VT-100 terminal connection, Telnet, web HTTP or SNMP.

Features

Specifications

▪ 1U, 19 (23)” 4-slot chassis ▪ 16 E1 (2.048Mb/s) Multiplexer with 100/1000Mbps Ethernet and RS-232 data (async) Interface (FMUX1001)

▪ 16 E1 (2.048Mb/s) Multiplexer with 10/100Mbps Ethernet and RS-232 data (async) Interface (FMUX101)

▪ RS-232 port for system console ▪ One alarm output port, one Order Wire port ▪ 4x 10/100/1000Base-T Ethernet ports (FMUX1001)

▪ 4x 10/100Base-T Ethernet ports (FMUX101) ▪ SNMP management ▪ LCD plus menu keys for local configuration ▪ Port based VLAN, tag based VLAN & bandwidth control ▪ Telnet and web based remote configuration ▪ 2 plug-in SFP slot for optical SFP module ▪ Forward 1024K byte packets on Ethernet port

Optical Interface Connector SFP - LC

Data rate 1.25G (FMUX1001), 155M (FMUX101)

Bit Error Rate Less than 10-11

Fiber MM 62.2/125μm, 50/125μmSM 9/125μm

Distance MM 2km. SM 15/30/50/80/120kmWDM 20/40/60/80km

Wavelength 1310, 1550nmElectrical Interface

Console, SNMP RJ45Ethernet 4x RJ45

Alarm RJ45

Standards E1:ITU-T, T1:ITU-T, AT&T, ANSI, Ethernet: IEEE 802.3xIndications PWR, Alarm, Phone, ACO, Port, ChannelsPower Input AC module IN : AC 90 ~ 264V, Out : DC 12V

DC module IN : DC 18 ~ 72V, Out : DC 12VPower Consumption < 25W

Dimensions 250 × 438 × 43mm (D × W × H)Weight 3.58 kgTemperature 0 ~ 50°C (Operating), 0 ~ 70°C (Storage)Humidity 10 ~ 90% non-condensingCertification CE, FCCMTBF 50,000 hrs

Application

FMUX1001 orFMUX101 FMUX1001 or

FMUX101

RS232 clear channelGbE or FE LAN

GbE or FE LAN

Order Wire

SmartView

BTS16E1

16E1

RS232 clear channel

Order Wire

Customer Premise

Equipment

1+1 Optical Protection

Central Office (CO)

(CPE)STM1

ADM

Remote 3G BTS Connection Application

Mod

ularized 16E1/T1 M

ultiplexer FMUX1001 &

FMUX101

Modularized 16E1/T1 Managed Multiplexer

R

Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / sales@ctcu.com

2020 V1.0

12-3

10101

0101

12

FMUX1001 & FMUX101 Interface Module

Standards G.711 A-law (separate modules for FXO)

Distance 2km

Bandwidth 64K voice channel

Connector RJ45 x 4 (4 voice channel /per unit)

Standards G.711 A-law (separate modules for FXS)

Distance 2km

Bandwidth 64K voice channel

Connector RJ45 x 4 (4 voice channel /per unit)

Standards ITU-T, E1A

Card Type V.35/ RS-530 (Include X.21 and RS-449)/ RS-232 I/FBit rate n x 64K, n = 1 to 32

V.35 & RS-530 up to 2MbpsRS-232 up to 115.2Kbps (ASYNC)

Line code NRZClock Mode Transparent, Recovery, External (From data port ETC)

Internal (From oscillator)

Standards ITU-T G.703, G.704, AT&T TR-62411,ANSI T1.403

Ports 4 portsFraming Unframed (clear channel)E1 Data rate: 2.048 Mbps ±50 ppm

Line code: HDB3 / AMILine impedance: 120 ohms ±5%, 75ohms ±5%

T1 Data rate: 1.544 Mbps ±50 ppmLine code: B8ZS / AMILine impedance: 100 ohms ±5%

Receive Level Short haul - 15dBConnector RJ-45

Standards ITU-T G.703, G.704, G.706, G.732

Ports 4 portsFraming Unframed ( clear channel )Data rate E1 2.048 Mbps ± 50 ppmLine code E1 HDB3/AMIReceive Level Short haul - 15dBLine impedance E1 75 ohms ± 5%Connector BNC 75 ohms

4x E1 BNC I/F

Related Cables (Please see order information for more details)

V35 RS530 X21RS449

4x E1/T1 RJ45 I/F

4x Data Com I/F

4x FXO I/F 4x FXS I/F

Control Signal CTS always On or follows RTSDSR constantly ON, except during testloops (RS-530 DSR always connect to DTR)DCD constantly ON, except during fiber signal loss

Test Loops Local loop back, Remote loop back, V.54Connector Type Uses HD-68 pin D type Female with adapter

cables

RS232

Ordering InformationModel Name Description

FMUX1001-CH 1U 19” 4-Slot Rack Mount Chassis

FMUX101-CH 1U 19” 4-Slot Rack Mount Chassis

FMUX-AC Chassis Power Module 90~264VAC

FMUX-DC Chassis Power Module 18~72VDC

FMUX-4E1/T1-RJ45 4ch E1/T1 RJ45 interface card

FMUX-4E1/T1-Wire 4ch E1/T1 Wire Wrap interface card

FMUX-4E1/BNC 4ch G.703 E1 BNC interface card

FMUX-V35 V35 interface card with HD68M to 4 x MB34F cable (30cm)

FMUX-530 RS-530 interface card with HD68M to 4 x DB25F cable (30cm)

FMUX-449 RS-449 interface card with one HD68M to 4 x DB37F cable (30cm)

FMUX-X21 X.21 interface card with one HD68M to 4 x DB15F cable (30cm)

FMUX-232/Sync RS-232 Sync card with one HD68M to 4 x DB9F cable (30cm)

FMUX-232/Async RS-232 Async card with one HD68M to 4 x DB9F cable (30cm)

FMUX-4FXO 4 x FXO interface card

FMUX-4FXS 4 x FXS interface card

FMUX-Phone-2W 2 Wires order Wire (connect to analogue Telephone set)

FMUX-Phone-4W 4 Wires order Wire (connect to Ear-Mic set)

FMUX-EXT/CLK External clock interface card

ACDCAA : AC + ACDD : DC + DCAD : AC + DC

A : 4x E1 BNCB : 4x E1/T1 RJ45C : 4x E1/T1 WireD : 4x V.35E : 4x RS-232/AsyncF : 4x RS-530

2W : 2 Wire Phone4W : 4 Wire Phone

1001 : GbE101 : FE

G : 4x X.21H : 4x RS-449 I : 4x FXO

Card TypeFMUX - - -

Power Type Order Wire

J : 4x FXSL : EXT/CLK

M : 4x RS232/Sync

A A B C DC1 10 0 2 W

1001 : GbE Fiber Multiplexer 101 : FE Fiber Multiplexer

FMUX - CH1 0 0 1

Power Module

FMUX A C

I/F Line Card

FMUX V 3 5

Example:Chassis/Power/Line card Only Whole Set

Interface Module

Interface Mod

ule

16E1/T1 Managed Multiplexer

10101

0101

R

Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / sales@ctcu.com2020 V1.0

12-4

12

FMUX1600FMUX80016 or 8x E1/T1 + 4x GbE, ManagedFiber Multiplexer

The FMUX1600/FMUX800 is 1U 19” rack mountable, PDH fiber optical Multiplexer that transmits up to 16/8 E1/T1 + 4 x 10/100/1000Base-T Gigabit Ethernet over a single fiber optic link. The FMUX1600/FMUX800 chassis in available in three different power configurations; single AC, single DC, or AC+DC. The AC supplies operate from 90 ~ 240VAC while DC supplies operate from 18~60VDC. On the rear of the chassis, the BNC model provides 32/16 unbalanced 75 Ohm coaxial connections with BNC connectors while the RJ-45 model provides 16/8 balanced 120 Ohm connections over twisted pair wiring with RJ45 connectors . With two SFP sockets on fiber ports, the FMUX1600/FMUX800 gives you the fiber cabling connector SFP-LC, both multi-mode and single-mode are available as well as BiDi which allows bi-directional transmissions using only a single fiber cable. 1+1 Automatic optical line protection is also supported for the aggregate fiber ports. The standard FMUX1600/FMUX800 configuration may be viewed or set via serial VT-100 terminal connection or SNMP card with web, telnet, and SNMP management

Features

Specifications

▪ Provides 16/8 E1/T1 G.703 transparent transmission over fiber ▪ Provides 4x 10/100/1000 Mbit/s Ethernet Ports and 1x RS232 ch. ▪ Provides one RS232 channel ▪ Loopback test on E1/T1 fiber port ▪ Provides one hotline channel (order-wire) ▪ Supports full/half duplex, 10M/100M/1000M, auto-Negotiation ▪ Forward 10K byte jumbo packets on Ethernet port

▪ Supports 1+1 fiber line protection. Less than 50ms ▪ Complete alarm function and can monitor remote device status ▪ Power combination AC220V and DC-48V for redundant options ▪ Supports RS232 local management; Supports on-line f/w upgrade ▪ Supports Web, Telnet, SNMP management (optional)

Optical Interface Connector SFP- LCData rate 1.25GbpsBit Error Rate Less than 10-11

Distance MM 2km, SM 15/30/50/80/120kmWavelength WDM 20/40/60/80km

Electrical Interface

Connector Console : RS232 / SNMP : RJ45Ethernet : RJ45 (4-port)Alarm : RS232 / Order wire : RJ11

E1 Interface Standards ITU-T G.703, G.704, G.706, G.732Ports 8/16 portsData Rate 2.048 Mbps ± 50 ppmLine Code HDB3/AMIConnector RJ-45 for 120 ohms BNC for 75 ohms

T1 Interface Standards ITU-T G.703, G.704, AT&T TR-62411, ANSI T1.403Ports 8/16 ports

T1 Interface Data Rate 1.544 Mbps ±50 ppmLine Code B8ZS / AMIConnector RJ-45 for 100 ohms

Certification CE, FCC, RoHS compliantStandards ITU-T G.703, G.823 and G.742, ANSI, AT&T, IEEE 803.2,

IEEE 802.3u, IEEE 802.3abIndications Power, Alarm, LBK, RD, LCK, RNG, ACO, Port, channelPower Input 90 ~ 240VAC, 18~60VDCPower Consumption <25W

Dimensions 250 x 438 x 43mm (D x W x H)Weight 3.58kgTemperature 0 ~ 60°C (Operating), -10 ~ 70°C (Storage)MTBF 50,000 hrs

Application

FMUX1600

Remote

1+1 Protection

Local

RS232 clearchannel

RS232 clearchannel

FMUX1600

Order Wire 3G BTS

16 E1/T1

SDHADM

GbE

Order Wire

GbE

16E1/T1

SmartView

Remote 3G BTS connection Application

16E1/T1 Managed

Multiplexer FM

UX1600 & FM

UX80016E1/T1 Managed Multiplexer

R

Specifications & design are subject to change without prior notice. Please visit CTC Union website for more details. www.ctcu.com / sales@ctcu.com

2020 V1.0

12-5

10101

0101

12

Ordering InformationModel Name DescriptionFMUX1600B-AD 16x E1 BNC + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power

FMUX1600R-AD 16x E1/T1 RJ-45 + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power

FMUX800B-AD 8x E1 BNC + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power

FMUX800R-AD 8x E1/T1 RJ-45 + 4 x 10/100/1000Base-T Ethernet Fiber Multiplexer, build-in AC + DC Power

FMUX1600-SNMP SNMP Card with 10/100Base-TX Ethernet Port

FMUX800-SNMP SNMP Card with 10/100Base-TX Ethernet Port

FMUX-Phone-2 2 Wires Order Wire

FMUX-Phone-4 4 Wires Order Wire

Model Name DescriptionFMUX1600-SNMP SNMP Card with 10/100Base-TX Ethernet Port

FMUX800-SNMP SNMP Card with 10/100Base-TX Ethernet Port

FMUX-Phone-2 2 Wires Order Wire

FMUX-Phone-4 4 Wires Order Wire

Power Type

FMUX1600–□–□□Example: FMUX1600– B – DC

FMUX–Phone –□Example: FMUX–Phone – 2

E1ConnectorType

SNMP option only required in one unit of paired linkNote:

Option Models

16E1/T1 Managed Multiplexer

16E1/T1 Managed

Multiplexer FM

UX1600 & FM

UX800