Upload
santosh-sandy
View
219
Download
4
Embed Size (px)
Citation preview
MAGNETIC AND ELECTRIC CIRCUITS IN MACHINES
1Dr.R.RAMESH
Dr. R. RAMESHAssociate Professor
Dept of Electrical and Electronics EnggAnna University , Chennai
1Dr.R.RAMESH
MAGNETIC CIRCUIT OF TRANSFORMER
2Dr.R.RAMESH2Dr.R.RAMESH
MAGNETIC CIRCUIT OF DC MACHINES
3Dr.R.RAMESH3Dr.R.RAMESH
MAGNETIC CIRCUIT OF INDUCTION MOTOR
4Dr.R.RAMESH4Dr.R.RAMESH
5Dr.R.RAMESH
6Dr.R.RAMESH
Electric circuit Magnetic circuitThe emf circulates current in a closed path
The mmf creates flux in a closed path.
Flow of current is opposed by resistance of the circuit.
The creation of flux is opposed by reluctance of the circuit.
The path of current is The path of flux is called The path of current is called electric circuit.
The path of flux is called magnetic circuit.
Resistance, R Reluctance,S=Current=emf/Resistance Flux=mmf/ReluctanceCurrent density,=Current/(area of cross-section)
flux density,B=Flux/(Area of cross-section)
7Dr.R.RAMESH
Electric circuit Magnetic circuit
Current actually flows in the electric circuit.
Flux does not flow, but it is only assumed to flow.
When current flows, the energy is spent
Energy is needed only to create the flux but not to energy is spent
continuously.create the flux but not to maintain it.
Resistance of the electric circuit is independent of current strength.
Reluctance of the magnetic circuit depends on total flux or flux density in the material.( this is due to saturation).
8Dr.R.RAMESH
ESTIMATION OF MMF OF A SECTION
Determine the flux in the concerned section
Calculate the cross-section of the section Calculate the flux density Calculate the flux density From calculated B , detemine H (mmf per
unit length) from B-H curve mmf for concerned section
= length of section * mmf per unit length
9Dr.R.RAMESH
ESTIMATION OF MMF OF A MACHINE
mmf = flux * relucatnce Reluctance will not be uniform Reluctance calculation
Reluctance of air-gap in machines with smooth armature
Reluctance of air-gap in machines with open armature slots
Reluctance of air gap neglecting fringing effect
Reluctance of air gap including fringing effect
10Dr.R.RAMESH
Reluctance of air-gap in machines with smooth
armature
11Dr.R.RAMESH
Reluctance of air-gap in machines with open
armature slots
12Dr.R.RAMESH
Reluctance of air gap fringing effect
13Dr.R.RAMESH
Reluctance of air-gap in machines with smooth armature (sg )
lg / o L y s
Reluctance of air gap neglecting fringing effect
lg / o L (y s - w s)Reluctance of air gap including fringing effect
lg / o L (y s - K cs w s)Effect of ventilating ducts L = L - K n wEffect of ventilating ducts on reluctance of air gap
L = L - K cd nd wdK cs = Carters gap coefficients for slots depends on the ratio of slot opening /airgap length orthe empirical relation is 1/ {1+ (5lg /Ws )}
K cd = Carters gap coefficients for ducts the empirical relation is 1/ {1+ (5lg /Wd )}
14Dr.R.RAMESH
Kgs : Gap contraction factor for slotsReluctance of air gap in machine with open armature
slots / Reluctance of air gap in machine with smooth armature = ys/ys
Kgd : Gap contraction factor for ductsReluctance of air gap in machine with open armature
radial ducts / Reluctance of air gap in machine without armature radial ducts = L/L armature radial ducts = L/L
Kg : Total Gap contraction factor Reluctance of air gap in machine with slotted
armature & ducts / Reluctance of air gap in machine with smooth armature without ducts
Kg = Kgs * KgdKgs = Kgss * Kgsr (for induction motor)
15Dr.R.RAMESH
MMF
mmf required for air gap in machine= 8,00,000 Bav kg lg
if armature is smooth kg =1slot , no ducts kg = Kgssmooth and with ducts kg = Kgd
16Dr.R.RAMESH
MMF CALCULATION FOR TEETH:The calculation of MMF for producing flux in the teeth
of the machine is difficult because :i) The teeth are tapered when parallel sided slots are
used and this results in variation in the flux densityover the depth of the tooth.over the depth of the tooth.
ii) The slots provide another parallel path for the fluxflow, the teeth are normally worked in saturationand hence r becomes low.
17Dr.R.RAMESH
Following METHODS are usually employed for the calculation of MMF required for the tapered teeth:-
i) GRAPHICAL METHOD :ATt = at mean x lt
ii) SIMPSONS RULE :ii) SIMPSONS RULE :at mean = (at1 +4 at2 + at3)/6 A/miii) BT1/3 METHOD : ATt = at1/3 x lt , where at1/3 = MMF for corresponding to B at 1/3 rd
height from the narrow end.
18Dr.R.RAMESH
Graphical Method
19Dr.R.RAMESH
B app= total flux in a slot pitch / Tooth area
B real = Actual flux in a tooth/Tooth B real = Actual flux in a tooth/Tooth area
20Dr.R.RAMESH
Magnetic leakage The flux which passes through unwanted
path is called the leakage flux. Leakage coefficient
= Total flux/ useful flux= (useful flux+ leakage flux) / useful flux
21Dr.R.RAMESH
Types of leakage flux Slot leakage flux Tooth top leakage flux Zigzag leakage flux Zigzag leakage flux Overhang leakage flux Harmonic leakage flux Skew leakage flux Peripheral leakage flux
22Dr.R.RAMESH
Slot leakage flux
23Dr.R.RAMESH
Tooth top leakage flux
24Dr.R.RAMESH
Zigzag leakage flux
25Dr.R.RAMESH
26Dr.R.RAMESH
Dr.R.RAMESH 27