839

Technical Data sheet for Part-turn Worm Gearboxes Technical Data sheet for Multi-turn Bevel Gearboxes

40

Dimension Data sheet for Multi-turn Bevel Gearboxes

TECHNICAL DATA FOR PART-TURN WORM GEARBOXES (FLANGE MOUNTED) AND PRIMARY REDUCTION GEARS GS 40.2 GS 125.2/VZ 4

Application Manual operation and motor operation of valves (e.g. butterfly valves,

ball valves, louver valves)

For special applications, please consult AUMA.

Worm gearboxes GS 40.2 GS 125.2 with primary reduction gearing VZ 4 Valve Gearboxes

Max.

Permissible valve torque

Valve attachment

Gearbox size

Suitable primary

reduction gearing Factor1)

Turns for

90 Input shaft

Max. input torques

Weight2)

in Nm up to

Flange acc. to EN ISO

5211

Max. shaft

diameter in mm Type

Reduction ratio (i)

mm in Nm GS+VZ

kg GS VZ GS+VZ

420 F07

3)

F10 25 GS 40.2 - 21:1 - 21:1 9 5.25 20 47 3.5

1000 F103)

F12 36 GS 63.2 - 39:1 - 39:1 16.7 9.75 20 60 9

2000 F123)

F14 48 GS 80.2 - 40:1 - 40:1 17.3 10 20 116 13.5

4000 F143)

F16 60 GS 100.2

- 40:1 - 40:1 17.3 10 30 232 30

VZ 4 40:1 3.92:1

157:1 58.5 39 20 68 34

8000 F163)

F25 80 GS 125.2

- 52:1 - 52:1 22.5 13 30 356 43

VZ 4 52:1 3.92:1

204:1 75.5 51 20 106 47

Gearbox size

Primary reduction gearing

Possible combinations with multi-turn actuators

Multi-turn actuator

Flange mounting of

actuator

Max. weight4)

Operating times for 50 Hz5)

in seconds for 90 at actuator speed in rpm

Actuator for max. input

torque

Type 4 5.6 8 11 16 22 32 45 63 90 125 180 EN ISO

5210 DIN 3210

GS+VZ+SA max. kg

GS 40.2 - 40 28 20 14 - - - - - - SA6 F10 G0 37

GS 63.2 - 146 104 73 53 36 27 18 13 - - - - SA6 F10 G0 42

GS 80.2 - 150 107 75 55 38 27 19 14 - - - - SA12 F10 G0 47

GS 100.2 - 150 107 75 55 38 27 19 14 - - - - SA25 F14 G 102

VZ 4 589 420 296 216 148 108 74 54 37 27 19 13 SA12 F10 G0 67

GS 125.2 - 195 139 98 70 49 35 24 17 12 - - - SA50 F14 G 143

VZ 4 765 546 384 274 192 137 99 69 48 35 24 176) SA12 F10 G0 80

1) Conversion factor from output torque to input tor q u e to determine the actuator size. This can be use d to select the actuator for torque other than the m ax. permissible valve torque.

2) With coupling (with pilot bore), grease filling i n the gear housing and without handwheel 3) Observe maximum torque for valve mounting flange s according to EN ISO 5211 4) With coupling (with pilot bore) and grease filli n g in the gear housing, multi-turn actuator AUMA NO R M with 3-phase AC motor, standard electrical connec t ion,

output drive E type and handwheel 5) Standard values at 50Hz, at 60 Hz the speeds inc r e ase by 20% and the operating times are reduced to 83% of the indicated values 6) Observe max. output torque of the multi-turn act u ator.

We reserve the right to alter data according to imp rovements made. Previous documents become invalid w ith the issue of this document.

We reserve the right to alter data according to improvements made.

1.

At max.output torque 2.

Conversion factor Output torque: Input Torque

3.

The permissible axial forces are considerably beyond the max.thrust of actuators available

when converting rotary to linear movement by using

trapezoidal thread 4.

Gearbox without hand wheel and actuator mounting flange

5.

Observing the permissible effort at hand wheel 6.

Depending on required gearbox output torque

*Option Can be provided on request.

Features and functions Type of duty

Short time duty S2-15 min ( OPEN -CLOSE Duty)

Direction of rotation

Clockwise rotation at input shaft results in

clockwise rotation

at output drives Input shaft

Cylindrical with parallel key according to IS 2048

Operation

Motor operation

With electric multi-turn actuator

Flanges for mounting of multi-turn actuator as per standard ENISO5210/DIN3210

Manual

operation

Via hand wheel

Available hand wheel

diameters, selection according to the max. output torque

Type

ABG

14.2

ABG

16.2

ABG

25.2

ABG

30.2

Hand wheel dia mm

350/400

400/640

500/640

640/800

Valve attachment

Valve attachment

Dimensions according to EN ISO 5210

Service conditions

Mounting position

Any position

Enclosure protection according to IS/IEC 60529

Standard

IP67 -

Dust proof & water tight

Option

IP 68 -

Enclosure can be provided on request

Corrosion protection

Standard

Suitable for installation in industrial units, in water or power plants with a low pollutant concentration

Option

Others on request

Paint

Standard

Powder coating as primer

+ Epoxy finish paint

Option

Other paints on request

Colour

Standard

Smoke grey Code 692 as per IS:5

Option

Other coloures

on request

Ambient TemperatureStandard

20 C to +80 C

Option Other temperature requirements on request.

BEVEL GEARBOX ABG14.2-ABG30.2

Technical data Gearbox Type

ABG14.2 ABG16.2 ABG25.2 ABG30.2 Max. Output torque Nm 750 1500 2500 5000 Reduction ratio 4:1 4:1 6:1 8:1 Input torque1)Nm 208 417 463 694 Mech. advantage2) 3.6 3.5 5.4 7.2 Stem dia Max.mm 50 60 72 100 Thrust Permissible for A type3)kN 160 200 320 450 Input shaft dia mm 30 30 30 30 Output drive - Type A type Weight4) kg 16 32 54 85 Hand wheel dia5)mm

350/400

400/640

500/640

640/800

Valve attachment

EN

ISO 5210

F16/F14*

F25/F16*

F30/F25*

F35/F30*

DIN 3210

G3/G*

G4/G3*

G5/G4*

G6/G5*

Combination with actuator

Actuator mounting flange

EN

ISO 5210

F14

F14

F14

F14

DIN

3210

G

G

G

G

Suitable actuator

SA25

SA50

SA50/ SA60

SA606)

Weight of actuator kg

71

99

99

99

/F16*

/G3*/SA100

BEVEL GEARBOX ABG14.2-ABG30.2

Dimension

Gearbox type d1 d2 d3 d4

d5 d6 D D1 D2 D3 D4 R d A G H h1 h2 L N U V

Min Max

ABG14.2 130 165 210 M20 20 50 76 350/400 175 140 100 18 17 30 130 160 94 5 30 195 225 62 9

ABG16.2 200 254 300 M16 30 60 89 400/640 175 140 100 18 17 30 185 174 96 5 24 265 280 70 9

ABG25.2 230 298 350 M20 25 72 114 500/640

175 140 100 18 17 30 237 186 110 5 30 302 337 90 3

ABG30.2 260 356 415 M30 30 100 140 640/800

175/210

140/ 165

100/ 130

18/ 22

17/ 25

30 256 225 129 5 45 323 356 112 13

X- As Per Requirement For manual operation

Mounting flange for electrically operated actuator

We reserve the right to alter data according to improvements made.

38

Dimension Data sheet for Multi-turn Bevel Gearboxes Technical Data sheet for Part-turn Worm Gearboxes

9

GS 40.2 GS 125.2/VZ 4 TECHNICAL DATA FOR PART-TURN WORM GEARBOXES (FLANGE MOUNTED) AND PRIMARY REDUCTION GEARS Features and functions Version Standard: clockwise rotation LR, counterclockwise r o t a t i o n R L , o p t i o n : R o r L Self-locking The gearboxes are self-locking when at s t a n d s t i ll u n d e r n o r m a l s e rvice conditions; strong vibration may

cancel the self-locking effect. While in motion, safe b r eaking is not guaranteed. If this is required , a separate brake must be used.

End stops Positive for both end positions by trave li n g n u t , s e n s i t iv e a d j u s t m e nt GS - Swing angle Fixed swing angle up to max. 120; s e t i n t h e f a c t o r y t o 9 2 unless ordered otherwise Mechanical position indicator Standard :

Option : Pointer cover for continuous position indication Protection cover for buried service instead of pointer cover.

Input shaft Cylindrical with parallel key according t o I S 2 0 4 8 . ( r e f e r t o t a b l e s page 8) Operation Motor operation With electric multi-turn actuator, d ir e c t l y o r t h r o u g h p r imary reduction gearing VZ

Flanges for mounting of multi-turn actuator (refer to tables page1). Type of duty Short-time duty S2-15 min. (openclose d u t y ) Manual operation Via handwheel, directly or through p r im a r y r e d u c t i o n g e aring VZ

Available handwheel diameters, selection according to the max. output torque: Type GS40.2 GS63.2 GS80.2 GS100.2 GS125.2

Primary red. gearing - - - - VZ 4 - VZ 4 Handwheel mm 250/300 250/300 300/400 300/400 250/ 3 0 0 4 0 0 / 5 0 0 3 00/400

Primary reduction gearing Primary redu c t i o n g e a r i n g - P l a n e t a r y V Z r e d u c t i o n r a t io f o r r e d ucing the input torques (refer to tables page 8). Valve attachment Valve attachment Dimensions accord i n g t o E N I S O 5 2 1 1 ( refer to table page 8)

Standard: Option:

GS 40.2 GS 125.2: with spigot GS 40.2 GS 125.2: without spigot

Splined coupling for connection to the valve shaft

Standard:

Option:

With pilot bore Worm gearbox can be repositioned 4 x 90 on coupling Machined with bore and keyway or square bore

Service conditions Mounting position Any position Enclosure protection according to IS/IEC 60529

Standard: Option:

IP 67, Totally enclosed protection against short time immersion in water IP 68, Enclosure can be provided on request

Corrosion protection Standard: Suitable for installation in industrial units, in w ater or power plants with a low pollutant concentration

Paint Standard: Option:

Epoxy primer + Epoxy finish paint Other paints on request

Colour Standard: Option:

Smoke grey Code 692 as per IS: 5 Other colours on request

Ambient temperature Standard: Option:

20 C to +80 C Others temperature requirements on request.

Lifetime Lifetime for 90 rotary movement

Gearbox size

GS 40.2 GS 63.2 GS 80.2 GS 100.2 GS 125.2

No. of cycles 7)

for max. torque 10,000 10,000 5,000 5,000 2,500

Lever gearboxes - type GF Refer to Pages 24 - 31.

7) Number of cycles according to standard EN 15714 -2

We reserve the right to alter data according to imp rovements made. Previous documents become invalid w ith the issue of this document.

BEVEL GEARBOX DIMENSIONAL DATA GK 40.1

We reserve the right to alter data according to improvements made. Previous data sheets become invalid with the issue of this data sheet.