International Conference on Mechanical, Industrial and Materials Engineering 2015 (ICMIME2015)11-13 December, 2015, RUET, Rajshahi, Bangladesh.

Paper ID: AB-000

Author’s Guidelines for ICMIME2015 Full Paper

Author(s) Name(s)1

1Author Affiliation(s)E-mail: icmime.ruet@gmail.com.com

Abstract

The abstract is to be written in this location in fully-justified italicized text. Use the word ”Abstract” as the title, in 12-point Times New Roman, boldface type, centered and, initially capitalized as shown above. The text should be in single spaced format with 10 point Times New Roman font. The maximum length of the abstract is to be kept within 150 words.

Keywords: 3-5 keywords, separated by commas.

1. IntroductionAll manuscripts must be original and written in English. These guidelines include complete descriptions of the fonts, spacing and related information for producing your camera ready paper.Page Limit: Camera ready paper must not exceed 06 (six) printed pages. The document size should be within 2 MB.

2. Formatting your paperAll printed material, including text, illustrations, and charts, must be kept within a print area of 14.96 cm wide by 24.62 cm high. Do not write or print anything outside the print area. All text must be in single spaced and single column format. Text must be fully justified.

3. Main title The main title (on the first page) should begin 3.5 cm from the top edge of the page, centered and in Times 14-point, boldface type. Capitalize the first letter of nouns, pronouns, verbs, adjectives, and adverbs; do not capitalize articles, coordinate conjunctions, or prepositions (unless the title begins with such a word). Leave 12-point blank lines after the title.

4. Author name(s) and affiliation(s)Author names and affiliations are to be centered beneath the title and printed in Times 12-point, non-boldface type. Affiliations of the authors are to be shown after the listing of the author names. In the case of multiple authorship, the respective affiliations are to be identified by superscript, as illustrated above. Include e-mail addresses if possible. Author information should be followed by two 12-point blank lines.

5. Second and following pages The second and following pages should begin 1.0 inch (2.54 cm) from the top edge. On all pages, the bottom margin should be 1.125 inch (2.86 cm) from the bottom edge of the page form A4 paper from the bottom edge of the page.

6. Type-style and fonts Wherever Times is specified, Times Roman or Times New Roman may be used.

7. Main textType your main text in 10-point Times, single-spaced. Do not use double-spacing. All paragraphs should be indented ¼ inch (approximately 0.5 cm). Be sure your text is fully justified- that is, flush left and flush right. Please do not place any additional blank lines between paragraphs.

.

Fig. 1. Experimental setup

Figure and table captions should be 10-point Times plain face. Initially capitalize only the first word of each figure caption and table title. Figures and tables must be numbered separately. For example: “Fig. 1. Title of the figure comes here.”, “Table 1. Title of the table comes here.” Figure captions are to be centered below the figures. Table titles are to be centered above the table. The figures should be in JPG format. It is desirable to place the figure or table at the top or bottom of the pages. Equations should be in 10-point, centered and numbered. The equations are to be referenced in the text as ‘(equation number)’.

(1)

8. First-order headings For example, “1. Introduction”, should be Times 12-point boldface, initially capitalized. flush left, with one blank line before, and one blank line after. Use a period (“.”) after the heading number not a colon.

Second-order headingsAs in this heading, they should be Times 11-point boldface, initially capitalized and indented with one blank line.

9. FootnotesIf possible do not use footnotes. In unavoidable case, place them at the bottom of the column on the page on which they are referenced. Use Times 8-point type, single-spaced.

10. AcknowledgementIf the work is supported or funded by any organization, then it must be acknowledged in this section.

Table 1. Historical data of vapor pressure of ammoniaAuthor Year T p Ref.

Keyes 1918 240-398 0.103-9.96 1Cragoe 1920 195-343 0.00563-3.31 25McKelvey 1923 195-195 0.1 26Beattie 1930 303-405 1.17-11.3 8Overstreet 1937 176-242 0.0008-0.1114 27

2

11. References List and number all bibliographical references in 9-point Times, single-spaced, at the end of your paper. When referenced in the text, enclose the citation number in square brackets, for example [1]. Where appropriate, include the name(s) of editors of referenced books.

[1] A.B. Smith, C.D. Jones, and E.F. Roberts, “Article Title”, Journal, Vol.1, No.2, pp. 1-10, 2012.[2] B.K. Das, M.E. Hoque, and M.R. Zaman, “Paper Title”, Proc. of the IEEE, Paper No.5, pp. 1-10, 2012.[3] C.D. Jones, A.B. Smith, and E.F. Roberts, Book Title, Publisher, edition, pp. 1-6, 2010.

3