PanelView Mounting Levers Installation Instructions · 9-in. Touch Widescreen– 8 Levers 12.1-in. Touch Widescreen–10 Levers 6-in. Touch Screen–4 Levers 7-in. Touch Widescreen–6

Installation Instructions

Original Instructions

PanelView Mounting LeversCatalog Number 2711P-RMCP

Use these mounting levers with these terminals:

• PanelView™ Plus 7 Performance terminals• PanelView 5310 terminals• PanelView 5500 terminals• PanelView 5510 terminals

Summary of ChangesThis publication contains new and updated information as indicated in the following table.

Topic Page

Summary of Changes 1

Prepare for Panel Mounting 2

Mounting Lever Orientation and Lock Sequence 3

Mount the Terminal in a Panel 5

Additional Resources 8

Topic Page

Changed part number from PN-411643 to PN-496931. 8

PanelView Mounting Levers

Prepare for Panel Mounting

Mounting levers insert into the slots around the bezel to secure the terminal in the panel. The number of mounting levers varies by terminal size. Each slot has six notches with alignment marks that are locking positions for a mounting lever. The thickness of the panel in which you mount the terminal determines the locking position that is required to maintain NEMA, UL Type, and IP seals.

Table 1 - Mounting Lever Lock Position

ATTENTION:

• Disconnect all electrical power from the panel before making the panel cutout.• Make sure the area around the panel cutout is clear and that the panel is clean of any debris,

oil, or other chemicals.• Make sure that metal cuttings do not enter any components that are already installed in the

panel and that the edges of the cutout have no burrs or sharp edges.• Failure to follow these warnings can result in personal injury or damage to panel components.

IMPORTANT For complete installation instructions, see the following publications:

• PanelView Plus 7 Performance Terminals User Manual, publication 2711P-UM008• PanelView 5310 Terminals User Manual, publication 2713P-UM001• PanelView 5500 Terminals User Manual, publication 2715-UM001• PanelView 5510 Terminals User Manual, publication 2715P-UM001

Mounting Slot

Mounting Lever Lock

Position Panel Thickness RangeTypical Gauge

1 1.50…2.01 mm (0.060…0.079 in.) 16

2 2.03…2.64 mm (0.080…0.104 in.) 14

3 2.67…3.15 mm (0.105…0.124 in.) 12

4 3.17…3.66 mm (0.125…0.144 in.) 10

5 3.68…4.16 mm (0.145…0.164 in.) 8/9

6 4.19…4.80 mm (0.165…0.188 in.) 7

1 6

1 2 3 4 5 6Notch

Alignment Mark

2 Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018

http://literature.rockwellautomation.com/idc/groups/literature/documents/um/2711p-um008_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2713p-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715p-um001_-en-p.pdf


Mounting Lever Orientation and Lock SequenceFigure 1 - PanelView 5310 Terminals

3 1

2

Round Side Round Side

4

65

2

1

3

4

2 47

5

6

83 1

3 110

7

6

5

8

12.1-in. Touch Widescreen–10 Levers9-in. Touch Widescreen–8 Levers

7-in. Touch Widescreen–6 Levers6-in. Touch Screen–4 Levers

2 49

Flat Side Flat Side

IMPORTANT The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in other orientations.

Rockwell Automation Publication VIEW-IN001C-EN-P - April 2018 3


Figure 2 - PanelView Plus 7 Performance, PanelView 5500, and PanelView 5510 Terminals

Round Side

Flat Side Flat Side

Round Side

3 1

2 4

56

6.5-in. Touch Only–6 LeversPVP7, PV5500, and PV5510 Terminals

472

5 6

183

6.5-in. Keypad and Touch–8 LeversPVP7, PV5500, and PV5510 Terminals

11

2 48

6

7

53 1

9-in. Touch Only, 10.4-in. Touch Only–8 LeversPVP7, PV5500, and PV5510 Terminals

3 110

6

8

7

5

10.4-in. Keypad and Touch, 12.1-in. Touch Only–10 LeversPVP7, PV5500, and PV5510 Terminals

2 49 2 497

11

5

6

12

8103 1

15-in. Touch Only–12 LeversPVP7, PV5500, and PV5510 Terminals

10

14

11

13

129

15-in. Keypad and Touch–14 LeversPVP7, PV5500, and PV5510 Terminals

8 4 62

5 1 73

10

16

14

12

11

13

15

9

19-in. Touch Only–16 LeversPVP7, PV5500, and PV5510 Terminals

8 4 62

5 1 73

7-in. Touch Only–6 LeversPV5510 Terminals Only

3 1

2 4

56

IMPORTANT The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in other orientations.



Mount the Terminal in a PanelFollow these steps to mount your PanelView terminal in a panel cutout.

1. Use the cutout template that is shipped with your terminal to mark the cutout dimensions and cut the hole in the panel.

See Panel Cutout Dimensions on page 8 if you do not have the cutout template.

2. Verify that the sealing gasket is present on the terminal.

This gasket forms a compression type seal. Do not use sealing compounds.

3. Insert and stabilize the PanelView terminal in the panel cutout.

a. Depending on your terminal model, insert the mounting levers in the top corner slots by using the orientation in Mounting Lever Orientation and Lock Sequence that starts on page 3.

b. Rotate the round side of the mounting levers toward the panel.

c. Tilt the terminal toward the panel cutout and guide the terminal upward into the cutout; make sure that the mounting levers stay intact.

IMPORTANT Catalog number 2711P-RMCP mounting levers are used only with PanelView 5310, PanelView 5500, PanelView 5510, and PanelView Plus 7 Performance terminals(1). Do not use these mounting levers with other PanelView terminals.

(1) These mounting levers do not work on PanelView Plus 7 Performance stainless steel terminals.

TIP The mounting levers in the top corner slots help to stabilize the terminal in the panel while you install the remaining mounting levers.

Flat Side

Round Side

10.4-in. terminal shown in this example.



d. Pull the top of the terminal toward you to verify that the mounting levers are still intact and the terminal is stabilized in the panel.

e. Depending on your terminal model, insert the remaining mounting levers in the slots by using the orientations in Mounting Lever Orientation and Lock Sequence that starts on page 3.

f. Reposition the top two mounting levers so that the flat side of the levers makes contact with the panel.The direction that you rotate the mounting levers varies for each terminal size.

4. Slide and rotate each lever to a notch that is one or two positions greater than the final lock position; start with the first lever in the sequence.

For example, if the final lock position is 3, slide the lever to notch 4 or 5.

a. See Mounting Lever Lock Position on page 2 for the final lock position of the mounting levers.

b. See Mounting Lever Orientation and Lock Sequence that starts on page 3 for the locking sequence of your terminal model.

c. Rotate each mounting lever until the flat side comes in contact with the panel.

TIP Use an erasable marker or grease pencil to mark the alignment marks for visibility of the slot positions and to mark the final lock position.

4 5

Flat Side

Flat Side in Contact With the Panel



5. Depending on your terminal model, adjust each mounting lever to its final lock position by using the Mounting Lever Orientation and Lock Sequence that starts on page 3.a. Unlock mounting lever one in the sequence by rotating it away from the panel.

b. With the mounting lever positioned vertically to the slot, slide the mounting lever to the final locking position as shown in Mounting Lever Lock Position on page 2.The outer notch of the mounting lever aligns with the bezel indentation.

c. Carefully rotate the mounting lever back toward the panel.

d. Lock the remaining mounting levers to their final position.

6. Inspect all mounting levers to make sure each is in the correct locked position.

The notch on the outside of mounting lever shows its locked position. These two views show the mounting levers that are locked in position 3.

TIP If the mounting levers are over torqued, they are designed to break off the pin to guard against damage to the bezel. If a pin is broken, turn the mounting lever over and use the other pin to continue the installation.

ATTENTION: All mounting levers must be in the correct locked position and follow the correct lever installation sequence to provide an adequate gasket seal between the terminal and the panel. Rockwell Automation assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.

OR

11

Outer Notches

Top View

Side View


Table 2 - Panel Cutout Dimensions

Additional ResourcesThese documents contain more information about related products from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Terminal Size Input Type Height, mm (in.) Width, mm (in.)6-in. Touch 123 (4.84) 156 (6.14)

6.5-in.Keypad and touch 142 (5.59) 237 (9.33)Touch 142 (5.59) 184 (7.24)

7-in. Touch 150 (5.90) 210 (8.25)9-in. Touch 162 (6.38) 252 (9.92)

10.4-in.Keypad and touch 224 (8.82) 335 (13.19)Touch 224 (8.82) 269 (10.59)

12.1-in. Touch 218 (8.58) 312 (12.28)

15-in.Keypad and touch 290 (11.42) 418 (16.46)Touch 290 (11.42) 353 (13.90)

19-in. Touch 383 (15.08) 457 (17.99)

Resource DescriptionPanelView Plus 7 Performance Terminals User Manual, publication 2711P-UM008

Provides details on how to install, configure, and operate the PanelView Plus 7 Performance terminals.

PanelView 5510 Terminals User Manual, publication 2715P-UM001

Provides details on how to install, configure, and operate the PanelView 5510 terminals.

PanelView 5500 Terminals User Manual, publication 2715-UM001


PanelView 5310 Terminals User Manual, publication 2713P-UM001


Cutout Templates for PanelView Plus 7 Performance and PanelView 5500 Terminals, publication VIEW-DS001

Provides cutout templates for the PanelView Plus 7 Performance and PanelView 5500 terminals.

Cutout Template for PanelView 5510 Terminals, publication 2715P-DS001

Provides cutout templates for the PanelView 5510 terminals.

Cutout Template for PanelView 5310 Terminals, publication 2713P-DS001

Provides cutout templates for the PanelView 5310 terminals.

Allen-Bradley, PanelView, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website athttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication VIEW-IN001C-EN-P - April 2018 PN-xxxxxxSupersedes Publication VIEW-IN001B-EN-P - February 2018 Copyright © 2018 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

*PN-496931*PN-496931

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.pagehttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715p-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2711p-um008_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2713p-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/ds/VIEW-ds001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/ds/2713p-ds001_-en-p.pdfhttp://www.rockwellautomation.com/literature/http://literature.rockwellautomation.com/idc/groups/literature/documents/ds/2715p-ds001_-en-p.pdfhttp://www.rockwellautomation.com

PanelView Mounting Levers Installation InstructionsSummary of ChangesPrepare for Panel MountingMounting Lever Orientation and Lock SequenceMount the Terminal in a PanelAdditional ResourcesContact Information

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Average /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages false /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Average /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

Introduction_Category Types

This tab summarizes Rockwell Automation Global Sales and Marketing preferred printing standards. It also provides guidance on whether a publication should be released as JIT (print on demand) or if it requires an RFQ for offset printing.Find your publication type in the first section below. Use the assigned Printing Category information to determine the standard print specifications for that document type. The Printing Categories are defined below the Publication Type section. Note there may be slightly different print specifications for the categories, depending on the region (EMEA or Americas).For more information on Global Sales and Marketing Printing Standards, see publication RA-CO004 in DocMan.

Publication Type and Print Category

Publication TypeOff Set Print Category Spec. (See table below)JIT Spec. (See table below)DescriptionOrder Min **Order Max **Life Cycle Usage / Release Option

ADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale / Internal

APA3D2Application Solution or Customer Success Story5100Presale / External

ARNANAArticle/Editorial/BylineNANAPresale / Internal

(press releases should not be checked into DocMan or printed)

ATB3, B4D5Application techniques5100Presale / External

BRA2 Primary, A1NABrochures5100Presale / External

CAC2 Primary, C1NACatalogue150Presale / External

CGNANACatalogue Guide150Presale / External

CLNANACollection550Presale / External

COA5, A6, A9D5Company Confidential InformationNANANA / Confidential

CPE-onlyE-only, D5Competitive Information550NA / Confidential

DCE-onlyE-onlyDiscount SchedulesNANAPresale / Internal

DIA1, A3NADirect Mail5100Presale / Internal

DMNANAProduct Demo550Presale / Internal

DSB3D5Dimensions Sheet15Post / External

DUB3D5Document Update15Post / External

GRB2D6Getting Results15Post / External

INB3 Primary, B2D5, D6Installation instructions15Post / External

LMNANALaunch Materials550Presale / Internal

PCB3D5Packaging Contents

PLE-only primary, B3E-onlyPrice List550Presale / Internal

PMB2D6Programming Manual15Post / External

PPA3D1Profile (Single Product or Service). NOTE: Application Solutions are to be assigned the AP pub type.5100Presale / External

QRB2 primary, B3, B5D5, D6Quick Reference15Post / External

QSB2 primary, B3, B5D5, D6Quick Start15Post / External

RMB2D5, D6Reference Manual15Post / External

RNB3D5Release Notes15Post / External

SGB1 Primary, B4D5, D6Selection Guide Colour550Presale / External

SGB2D5, D6Selection Guide B/W550Presale / External

SPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to be assigned the PP pub type.5100Presale / Internal

SRB2, B3D5, D6Specification Rating Sheet5100Presale / External

TDB2 Primary B3, B4, B5D5, D6Technical Data550Presale / External

TGB2, B3D6Troubleshooting Guide15Post / External

UMB2 Primary, B4D6User Manual B/W15Post / External

WDB3D5Wiring Diagrams / Dwgs15Post / Internal

WPB3 Primary, B5D5White Paper550Presale / External

** Minimum order quantities on all JIT items are based on the publication length. **

Publication lengthMinimum Order Quantity

77 or more pages1 (no shrink wrap required)

33 to 76 pages25

3 to 32 pages50

1 or 2 pages100

Pre-sale / MarketingAll paper in this category is White Brightness, 90% or better. Opacity 90% or better

CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements

A14 color170 gsm 2pp100# gloss cover, 100# gloss text

A24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss text

A34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss cover, 80# gloss text

A42 color170gsm Silk – 120gsm Silk80# gloss cover, 80# gloss text

A52 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text

A61 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text

A74 color cover2 color textSelection GuideCategory being deleted10 Point Cover C2S50# matte sheet text

A84 color coverCategory being deleted50# matte sheet text, self cover

2 color text

Selection Guide

A92 color100gsm bond50# matte sheet text, self cover

Selection Guide

Gray shading indicates Obsolete Print Catagories

Post Sale / Technical Communication


B14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S

2 color text50# matte sheet text

B21 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B31 color100gsm bond50# matte sheet text, self cover

B42 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B52 color100gsm bond50# matte sheet text, self cover

Catalogs


C14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S

4 color text45# Coated Sheet

C24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S

2 color text32#-33# Coated Sheet

JIT / PODAll paper in this category is White Brightness, 82% or better. Opacity 88% or better


D14 color170gsm white silk80# gloss cover, coated 2 sides

D24 color120gsm white silk80# gloss text, coated 2 sides, self cover

D34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss text coated 2 sides

D41 color160gsm tab90# index

D51 color80gsm bond20# bond, self cover

D61 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D72 color160gsm tab90# index

D82 color80gsm bond20# bond, self cover

D92 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D10Combination: 4 color cover, with 2 color bodyCover 160gsm with Body 80gsm90# index, 20# bond

Gray shading indicates Obsolete Print Catagories

Just In Time (JIT) or Off Set (OS)?

Use these guidelines to determine if your publication should be JIT (just in time/print on demand) or if it would be more economical to print OS (offset/on a press). OS print jobs require an RFQ (Request For Quote) in US. If your job fits into the “Either” category, an RFQ is recommended, but not required. In the US, RA Strategic Sourcing will discourage or reject RFQs for jobs that fall within the JIT category. Guidelines differ for black & white and color printing, so be sure to check the correct tables.

Black & White Printing

Color Printing

Color Printing

Print Spec Sheet

JIT Printing SpecificationsRA-QR005J-EN-P - 6/14/2013

Printing SpecificationYOUR DATA HEREInstructionsNO

(required) Publication Number:VIEW-IN001C-EN-PSample: 2030-SP001B-EN-P11” x 17”LOOSE -Loose LeafYESPre-sale / MarketingTOP

Use Legacy Number:YES or NO8.5” x 11”PERFECT - Perfect BoundA1LEFT

Legacy Number if applicable:Sample Legacy Number: 0160-5.338.375” x 10.875SADDLE - Saddle StitchA2RIGHTCORNER

Publication Title:PanelView Mounting Levers Install InstructionSample: ElectroGuard Selling Brief80 character limit - must match DocMan Title8.25” x 11” (RA product profile std)PLASTCOIL - Plastic Coil (Coil Bound)A4BOTTOMSIDE

Used in Manufacturing:YESYES or NO - If Yes, must have Part No. listed below8.25” x 10.875”STAPLED1 -1 positionA3

Part Number:PN-496931If SAP Part Number, be sure to enter PN- before the number7.385” x 9” (RSI Std)STAPLED1B - bottom 1 positionA5

(required) CategoryD5Select Print Category A,B,C or D from category list, on "Introduction_Category Types" tab6” x 4”STAPLED2 - 2 positionsA6

Paper Stock Color:White is assumed. For color options contact your vendor5.5” x 8.5” (half-size)THERMAL - Thermal bound (Tape bound)A7

Ink Color:One color assumes BLACK / 4 color assume CMYK / Indicate PMS number here4.75” x 7.75”THERMALO - Thermal Bound (Tape bound - offline)A8

(required) Page Count ofPublication:8Total page count including cover. Enter PAGE count, not SHEET count4.75” x 7” (slightly smaller half-size)A9

(required) Finished Trim Size Width:8.5” x 11”This is sheet size, before folding4.25" x 5.50"Post Sale / Technical Communication

Fold:Half or V or Single FoldReview key below. Leave blank if folded for saddle stitching4” x 6”B1

Finished Fold Size:4.25 x 2.75This is size after folding is completed3” x 5”B2

Binding/Stitching:SADDLE - Saddle StitchReview key below9” x 12” (Folder)B3None

Stitching Location:Blank, Corner or SideA4 (8 ¼” x 11 ¾”) (210 x 297 mm)B4Half or V or Single Fold

Drill Hole (Yes/No):All drilled publications use the 5-hole standard, 5/16 inch-size hole and a minimum of ¼ inch from the inner page border.A5 (5.83” x 8.26”) (148 x 210 mm)B5C or Tri-Fold

Number of Tabs Needed:5 tab in stock at RR Donnelley36” x 24” PosterCatalogsDbleParll

Number of Pages per Pad:Average sheets of paper. 25, 50 75,100 Max24” x 36” PosterC1Sample

Glue Location on Pad:Glue location on pads18” x 24” PosterC2Short (must specify dimensions between folds in Comments)

(required) Business Group:Marketing CommercialAs entered in DocManJIT/PODZ or Accordian Fold

(required) Cost Center:19134 - IAIf your Business Unit is Marketing Commercial, add the appropriate division name after 19134 using the chart on the right. All other Business Units: Enter only the number as in DocMan, no description. Example - 1902119134 - Commerc 19134 - OEM 19134 - Compone 19134 - Power C19134 - Global 19134 - Process 19134 - IA 19134 - Service 19134 - IMC 19134 - Safety 19134 - Industr 19134 - Softwar19134 - Mkt Dig 19134 - US MarkeD1Microfold or French Fold - designate no. of folds in Comments - intended for single sheet only to be put in box for manufacturing

Comments:After the V fold and the booklet is saddle stitched, fold the pub 2 more times for a finished fold size of 4.25 x 2.75, with the part number visible on the outside of the fold.D2Double Gate

FoldsHalf, V, Single C or Tri

Dble Parll

Z or Accordian Microfold or French

Double Gate

Short FoldSaddle-Stitch Items All page quantities must be divisible by 4.Note: Stitching is implied for Saddle-Stitch -no need to specify in Stitching Location.80 pgs max. on 20# (text and cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24# (text and cover)

Perfect Bound Items940 pgs max. w/cover (90# index unless indicated otherwise)70 pgs. min. for spine without words200 pgs min. for spine with words

Plastcoil Bound Items530 pgs max. of 20# (if adding cover deduct equivalent number of pages to equal cover thickness) (90# index unless indicated otherwise)

Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover (90# index unless indicated otherwise)D3

D4

D5

D6

D7

D8

D9

MBD000B0209.bin

MBD000B020B.bin

MBD000B020C.bin

MBD000B020A.bin

MBD000B0205.bin

MBD000B0207.bin

MBD000B0208.bin

MBD000B0206.bin

MBD000B0203.bin

MBD000B0204.bin

Documents

PanelView Mounting Levers Installation Instructions · 9-in. Touch Widescreen– 8 Levers 12.1-in. Touch Widescreen–10 Levers 6-in. Touch Screen–4 Levers 7-in. Touch Widescreen–6