March 2016 143

LUMBER & MILLWORK

4 X 8 SHeetS tYPe 1/8” 1/4” 3/8” 1/2” 5/8” 3/4” 1” ACX Fir S1S * * * * * AAX Fir S2S * * Plum Creek Underlayment Fir B Crossband * * T&G Premium Underlayment Fir * Underlayment Fir C Crossband * * CDX Sheathing Fir * * * * Southern Yellow Pine Textured T 1-11 * Lauan (Meranti) * * * * SurePly Underlayment * A-B Marine * Pressure Treated .40 CDX * * Pryoguard Fire Retardant (Interior Use) * * * Red Oak VC A-4 A-2 A-1 Birch VC A-4 A-2 A-1 Primed MDO (Medium Density Overlay) G1S * MDO (Medium Density Overlay) G2S * MDF (Medium Density Fiberboard) Lite Weight * * MDF Beadboard Primed 2” oc * White Melamine G2S * Wackywood 4X8 (Short Grain Tube) * Wackywood 8X4 (Long Grain Can) * 7/16” 15/32” 5/8” 3/4”OSB * * * * nOte: all plywood thickness are nominal and are slightly less than indicated

Panels: Plywood & OSB

Metal Studs & Gypsum METAL STUDS 8’ 10’ 12’ 10’ Runner

3 5/8” 20 gauge * * * * 3 5/8” 25 gauge * * * * GYPSUM 3/8” 1/2” 5/8” 4 x 8 Drywall * * * 4 x 10 Drywall * * 4 x 12 Drywall * * 4 x 8 Blueboard * * 4 x 12 Blueboard * 4 x 8 Water Resistant *

144 March 2016

LUMBER & MILLWORK

4 x 8 Sheets code 3/4” T&G Subfloor adVan4834 5/8” T & G adVan4858tG 5/8” S. E. adVan4858 1/2” Square Edge adVan4812

www.Huberwood.com

defining Innovation

Floor coverings• Carpetandpad:MaybeinstalleddirectlyoverAdvanTechandHuberBlueflooringpanels.

• Vinyl: Aminimum 1/4” underlayment is recommended. Followfinished flooring manufacturer instructions.

• Hardwoodfloors:Maybeapplieddirectlyover23/32”AdvanTechflooring panels. For Huber Blue flooring, the National WoodFlooring Association (NWFA) and the National Oak FlooringManufacturers Association (NOFMA) recognize the use of 23/32” OSB subfloor under hardwood flooring. For installation of the hardwood flooring follow the recommendations of the manufacturer.

• Ceramic tile: Underlayment is required per ANSI Standard A-108withnotedexceptionof1-1/4”cementmortarapplicationmethod.

• Lightweight concrete: May be applied over AdvanTech andHuber Blue flooring following lightweight concrete manufac-turer’s instructions.

descriptionAdvanTechFlooringandSheathingAdvanTech®flooringdeliversthetotalperformancepackageofstrength,fastenerholding,moistureresistance,andquality.AdvanTechpanelshelpeliminatefloorbounceandsqueaksbydeliveringthehighestBuildingCoderecognizeddesignbending

strengthintheindustrycombinedwithhighsurfacedensitytokeepfastenerssecurelyinplace.Formoistureresistance,AdvanTechflooring–backedbya500daynosandguaranteeandlifetime

limitedwarranty-hasoneofthelowestwaterabsorptionratesinthewood-structuralpanelIndustry.AdvanTech flooring has been voted number one in quality for 12 consecutive years by builders.

Basic usesAdvantech isthefirststructural-usepanelwithproprietarydesigncapacities,whichare superiortothedesigncapacitiesofcommodityPS-2panels. Theyareusedinbothresidential

andcommercialconstructionforfloor,roofandwallsheathingapplications.AdvanTechFlooringpanelsareusedforbothsingle-layerandsub-floorapplicationsaswellasroofsheathing.AdvanTechSheathingpanelsareusedforroofandwallsheathingaswellassub-flooringintwo-layersystems.

THE AdvanTech® FLOORING AND SHEATHING LIMITED WARRANTY

FOR THE BUILDER AND CONTRACTOR:HuberEngineeredWoods(HEW)warrantstotheoriginalretailpurchaserthatitsAdvanTechflooringandsheathingwillnotdelaminatenorrequiresandingduetomoistureabsorptionduringinstallation.

FOR THE CONSUMER:Peaceofmind.TheAdvanTechflooringandsheathingpanelsusedinyourhomeareguaranteedtobefreeofmanufacturingdefectsforaperiodof50yearsfromthedateofmanufacture.

TM

www.advantechperforms.com

March 2016 145

LUMBER & MILLWORK

4 x 8 Sheets code 7/16”GreenZipCombo ZIPWaLL7161/2”OrangeZipCombo ZIPROOF12 5/8” GreenZipCombo ZIPROOF58 ZipR6Sheathing ZWR6

accessories/tools code Acrylic FlexTape ZIPFLeXtaPe4”x90’ZipTape ZIPWaLLtaPe 6”x90’ZipTape 6ZWt ZipLiquidFlash29ozTube ZIPLIQuIdFLaSHZipTapeGun ZIPWaLLGun

ZIP It tIGHt: the Fastest Way to the Perfect tight House

Discover ZIP System® SheathingandTape.It’saone-of-a-kindstructuralroofandwallsystemwithabuilt-inenergy-efficientbarrierthatkeepsmoistureoutandreducesairleakage,whilestillallowingpanelstoproperlydry.Plus,itgoesupinjusttwoeasysteps:1.Installthepanels,2.Tapetheseams.Fewerstepsresultsin40%fasterinstallationwhencomparedtotraditionalhousewrapandfelt.

ZIP System® R-Sheathing 5-in-1 System with Layers of InnovationForinstallationconvenienceandexceptional,long-termperformance,theall-in-oneZIPSystem®R-Sheathingpanelprovidesanewapproachtosealingandinsulatingthebuildingenvelope.Onepaneldeliversthermal,airandmoistureresistance,whileprovidingexcellentstrength and durability.

three thicknesses. two colors. It’s one panel that can do it all.The ZIP System®productlineisdesignedtostreamlineworkonthejobsite.Threepanel thicknessesletyouchoosethestrengthandprotectionyouneedforyourbuild.Eachoneisengineeredforuseonbothroofandwallapplications,meaningonepanelisallyouneed.

www.zipsystem.com

March 2016 181

LUMBER & MILLWORKPVc

www.kleerlumber.com

KLEER Trimboard• Consistent dimensions • Heat bendable• Nominal 3"-16" Widths• 18' & 20' Lengths

Konceal Trimboard• 3/4" x 3/4" Konceal Edge

to accept wood, cement or vinyl sidings

• Nominal 4" & 6" Widths• 18' Length

Konceal Corner• Single Piece - No Joint• 3/4" x 3/4" Konceal Edge• Nominal 4" & 6" Widths• 10' & 20' Lengths

KLEER Corner• Single Piece - No Joint• Square Edges• Nominal 4" & 6" Widths• 10' & 20' Lengths

KLEERFold• Folded & Laminated Kleer• Nominal 2" x 4" and

2" x 6"dimensions• 18' Length

KLEERStart• Siding starter strip• 3/4" Thickness works with

Kleer Konceal Trim Products• Nominal 6" & 8" Widths• 18' Length

KLEER Sheet• Woodgrain or Smooth• 1/4" to 1-1/4" Thick• 4' Width • 8' & 10' Sheet Stock*

KLEERBeed• 1/2" Thick• 4' x 8' & 4' x 10' Sheets• 2" On-Center Bead

KLEERLok• 1/2" Thick• Tongue & Groove with

Blind Nailing Flange• 3-1/4" Width (1-5/8" OC Bead)• 5" Width (2-1/2" OC Bead)

KLEER Moulding• Popular Profi les• Coordinates with

Trim Products

KLEERBlok (9)• Exterior mounting blocks for light

fi xtures, utility meters and more• Solid 1-1/4" thickness• Nominal 7" x 8", 8" x 12", 9" x 14",

16" x 18" and 18" x 24" sizes

KLEERWrap• Fast, economical post wrap • Moulding sets available• 4" x 4" , 6" x 6" ,

and 8" x 8" wraps

KLEERLok Moulding• Used to conceal the ends

of KleerLok and KleerBeed in long runs

• Nominal 3" Width• 16' Length

Sheet Stock

4 x 8 x 1/2" PVC Sheet 4 x 8 x 1/2" PVC 2" O.C. Beaded Sheet4 x 8 x 3/4" PVC Sheet4 x 10 x 3/4" PVC Sheet4 x 8 x 1" PVC Sheet

Trimboards

length12' 18' 20'– 1 x 3 –

1 x 4 1 x 4 5/4 x 41 x 5 1 x 5 5/4 x 51 x 6 1 x 6 5/4 x 61 x 8 1 x 8 5/4 x 8

1 x 10 1 x 10 5/4 x 101 x 12 1 x 12 5/4 x 12

Post Wraps for 4x4

4 x 4 x 10' 7" Outer WrapBed Moulding for Outer WrapBase Cap MouldingCrown Moulding

Post Wraps for 6x66 x 6 x 10' 7" Outer WrapBed Moulding for Outer WrapBase Cap MouldingCrown Moulding

STOCKING

182 March 2016

LUMBER & MILLWORK

For more details on any Kleer product, full installation guidelines and warranty information, please visit www.kleerlumber.com. Not all Kleer products or sizes are available in all areas. Please contact your local Kleer Dealer to verify sizes and product availability.

TIGHT TIGHT

1/16" 1/8" 1/16"

>1/16" >1/8" >1/16"

90°

50°

Below 50°

TIGHT

16"ON CENTER

8"

16" ON CENTER

2" MAX 2" MAX

2" MAX 2" MAX

To help maximize the beauty and performance of Kleer trimboards, please consider the following installation reminders:

• Whenever possible install Kleer over a continuous substrate.• Use the proper quantity and size of fasteners, applied in an even pattern so they will penetrate into

the substrate at least 1-1/2".• Leave the appropriate expansion spaces between pieces of Kleer based on the temperature at the

time of installation.• Use adhesives made for PVC products, like Kleer Cellular PVC Cement or Kleer Cellular PVC Adhesives

to join pieces of Kleer.• Use 100% acrylic latex house paint to fi nish Kleer if you choose a color with an LRV greater than or

equal to 55%.• Use a coating that is formulated specifi cally for exterior vinyl products if you choose a color with an

LRV less than 55%.• Use Kleer Structural Sealant to fi ll expansion gaps and nail and screw holes.

KE

Y R

EM

IND

ER

S

INSTALLATION KEY POINTS, PLEASE REFER TO THE KLEER INSTALLATION GUIDELINES FOR COMPLETE DETAILS

EXPANSION & CONTRACTION

• Like many building materials, Kleer will expand and contract with changes in temperature. This is normal and is not covered by the Kleer Limited Lifetime Warranty. Under normal conditions and when properly fastened, Kleer will expand/contract approximately 1/8" per 18' length of Kleer. Failure to use the proper type and quantity of fasteners may result in expansion and contraction greater than 1/8" per 18'.

• Kleer trimboards should be acclimated to the temperature conditions at the time of installation.

• Fastening Kleer along its entire length will help minimize expansion and contraction.

• When joining Kleer end-to-end (as in long-run applications) pieces may be joined together using scarf joints and Kleer Cellular PVC Cement or Kleer Cellular PVC Adhesive. If joints are glued together, create 1/16" expansion spaces per 18' of run at each end. These expansion spaces should be fi lled using Kleer Structural Sealant.

• Alternatively, rather than gluing pieces together for long runs, leave expansion spaces of approximately 1/8" between the pieces and fi ll with Kleer Structural Sealant. Use scarf joints for all expansion spaces between the pieces in long runs and leave a 1/16" space per 18' of run at each end.

- On cold days (temperatures at low end of the normal annual temperature range), increase expansion space between boards to slightly more than 1/8" per 18' length.

- On hot days (temperatures at high end of the annual temperature range), eliminate the expansion space and butt the pieces together tight.

FASTENING

• Fasten with stainless steel or hot-dipped galvanized nails with blunt tips and round heads (wood siding nails, box nails, etc.). Exterior coated or stainless steel trim-head screws (nothing smaller than a #6 screw) and Cortex® Fasteners may also be used.

• Do not use staples, wire nails or brads to fasten Kleer. Fasteners that can be bent with bare hands will not provide appropriate strength.

• Standard pneumatic nailers, set at 70-80 psi, may be used to fasten Kleer. Air pressure may be adjusted as necessary.

• Pre-drilling is not typically required unless using large nails or installing in temperatures below 40°.

• Fasten Kleer to a fl at, solid wood substrate at least 1-1/2" thick using nails or screws that penetrate into the substrate a minimum of 1-1/2".

• Kleer must have fasteners no more than 2" from each edge.

• Kleer trimboards 8" or narrower require two fasteners evenly spaced across the face of the board and fastened to 1-1/2" thick framing no more than 16" on-center. 10" and 12" Kleer trimboards require three fasteners evenly spaced across the face of the board and fastened to 1-1/2" thick framing no more than 16" on-center. When spanning framing greater than 16" on-center, use Kleer that is a minimum 5/4" (nominal) thickness. Never install Kleer on framing that spans greater than 24" on-center.

• When joining Kleer end to end (as in long-run applications) fasten within one inch of both sides of the joint using the proper size fasteners.

• Kleer sheets 3/4" thick or greater require fastening every four inches along no more than 16" on-center framing. Thinner sheets require fastening every four inches on framing no more than 12" on-center.

• Use of construction adhesive (along with mechanical fastening) may help to minimize expansion and contraction, particularly when Kleer is painted dark colors (LRV less than 55% – see PAINTING section in complete guidelines)

www.kleerlumber.com

March 2016 183

LUMBER & MILLWORK

Applicator GunsKLEER off ers applicator guns for both our 50 ml and 220 ml two-part adhesives. Both applicators are built of high quality materials to last. Our 50 ml gun is constructed of heavy plastic with the ability to accept up to a 10:1 ratio cartridge. The KLEER 220 ml gun is constructed with metal and is produced to last.

Kleer Quick Mixer Tips KLEER Quick Mixer Tips are available for both our 50 ml and 220 ml adhesive tubes. Get the perfect, on-ratio mix of KLEER Cellular PVC Adhesive each and every time. These twist lock mixers were designed with a low internal volume for less waste and greater value. With our 1:1 ratio cartridges, application is simple and eff ective.

Caulk Gun Adaptor KLEER off ers a Caulk Gun Adaptor for the fl exibility to use our 50 ml cartridges with a standard caulk gun.

ADHESIVES AND SEALANT FOR CELLULAR PVC TRIM PRODUCTSDESCRIPTION: Kleer Cellular PVC Cement is a superior quality, fast drying adhesive for bonding Kleer cellular PVC trim products.

FEATURES:• Color matched to Kleer cellular PVC trim products• Dries quickly to produce a strong, yet fl exible, bond• Outstanding resistance to weather and temperature extremes• Completely waterproof and can be used on wet surfaces• UV stable to resist yellowing and fading• Can be applied by brush or roller• Dried fi lms can be reactivated

DESCRIPTION: Kleer Cellular PVC Structural Sealant is a high performance, resilient, fl exible structural sealant that forms a durable, non-shrinking bond when used with Kleer cellular PVC trim products.

FEATURES:• Solvent free, 100% solids formula will not shrink so it is ideal

for fi lling nail holes• Aff ords 100% total joint movement for excellent performance in

fi lling expansion gaps• UV inhibitors resist yellowing and fading• Non-slump formula can be applied vertically and overhead• Can be applied to damp surfaces and won't run if rained upon• 30 minute skin-over signifi cantly reduces dirt pick-up. Can be painted in

1-2 hours with any 100% acrylic house paint• No unpleasant odor and zero VOC's

DESCRIPTION: Kleer Cellular PVC Adhesive is a durable, two-component adhesive for Kleer cellular PVC applications with a work life at 75oF of 4-7 minutes after mixing. It is ideal to fi ll nail holes and gaps up to 3/8" without the need for fasteners or biscuits, and can be used to smooth cut edges for a more fi nished look. It is EPA VOC and CARB compliant.

FEATURES:• Permanent unitizing structural adhesive• Easy to apply• Dries quickly and can be handled in 10-30 minutes• Completely waterproof • UV stable to resist yellowing and fading• Color matched to Kleer Cellular PVC• Paintable

DESCRIPTION: Kleer Cellular PVC Nail Stick is a two-part epoxy that can be used to fi ll nail holes and other minor imperfections in the surface of Kleer cellular PVC products. Once mixed, Kleer Cellular PVC Nail Stick cures to an off -white to light gray color and can easily be sanded, drilled and painted.

FEATURES:• High performance two-part epoxy creates a hard, durable fi nish• Easily fi lls nail holes and other minor imperfections on the surface of

Kleer cellular PVC products• Cures to an off -white or light gray color• Once fully cured, it can be drilled, sanded and painted• UV inhibitors resist yellowing• Doesn't sag and won't shrink after curing

Kleer Cellular PVC Cement

Kleer Cellular PVC Structural Sealant

Kleer Cellular PVC Adhesive

Kleer Cellular PVC Nail Stick

www.kleerlumber.com