PANASONIC NV GS80 85 Manual Reparatii

© 2007 Matsushita Electric Industrial Co., Ltd. Allrights reserved. Unauthorized copying anddistribution is a violation of law.

NV-GS80E NV-GS80EBNV-GS80EE NV-GS80EFNV-GS80EG NV-GS80EKNV-GS80EP NV-GS85EENV-GS85GC NV-GS88GKVol. 1Colours

(S)...................Silver Type

Digital Video Camcorder

ORDER NO. VM0702004CE

1 Safety Precautions 3

1.1. General Guidelines 3

2 Warning 4

2.1. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices 4

2.2. Caution for AC Cord (VJA0940 type) 5

2.3. How to Replace the Lithium Battery 6

3 Service Navigation 7

3.1. Introduction 7

3.2. About Lead Free Solder (PbF) 7

4 Specifications 8

5 Service Mode 9

5.1. Error Display 9

5.2. Service Menu 9

6 Service Fixture & Tools 11

6.1. Service Fixture and Tools 11

6.2. Service Position 13

6.3. Removal/Installation of F.P.C. From Non ZIF (Zero

Insertion Force) Connector 15

6.4. Method for Loading/Unloading of Mechanism 16

6.5. EEPROM Data 16

6.6. Special Note 17

7 Disassembly and Assembly Instructions 18

7.1. Cabinet Section 18

7.2. Mechanism Section 36

8 Measurements and Adjustments 38

8.1. Mechanical Adjustment 38

8.2. Electrical Adjustment 40

9 Maintenance 42

9.1. Cleaning Lens, Viewfinder and LCD Panel 42

9.2. How to use the DVC Head Cleaning Tape / VFK1451 42

10 Block Diagrams 43

11 Schematic Diagrams 45

11.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT

NOTES 45

11.2. FRONT SCHEMATIC DIAGRAM 46

11.3. LCD BACKLIGHT SCHEMATIC DIAGRAM 47

11.4. EVF BACKLIGHT / EVF FPC / BATTERY CASE

SCHEMATIC DIAGRAMS 48

11.5. CCD / SIDE L OPERATION / LCD SW SCHEMATIC

DIAGRAMS 49

11.6. INTERCONNECTION SCHEMATIC DIAGRAM 50

12 Printed Circuit Board 51

12.1. FRONT P.C.B. 51

12.2. LCD BACKLIGHT P.C.B. 52

13 Exploded Views 53

13.1. MAIN PARTS SECTION 53

13.2. FRONT AND BOTTOM CASE SECTION 54

13.3. SIDE R SHAFT UNIT AND LCD SECTION 55

13.4. CCD AND LENS SECTION 56

13.5. EVF SECTION 57

13.6. MECHANISM SECTION 58

13.7. PACKING PARTS AND ACCESSORIES SECTION 59

14 Replacement Parts Lists 60

14.1. MECHANICAL REPLACEMENT PARTS LIST 60

14.2. ELECTRICAL REPLACEMENT PARTS LIST 61

15 Voltage Chart 64

CONTENTS Page Page

2

1 Safety Precautions1.1. General Guidelines 1. IMPORTANT SAFETY NOTICE

There are special components used in this equipmentwhich are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,Exploded Views and Replacement Parts List. It is essentialthat these critical parts should be replaced withmanufacturer’s specified parts to prevent shock, fire, orother hazards. Do not modify the original design withoutpermission of manufacturer.

2. An Isolation Transformer should always be used during theservicing of AC Adaptor whose chassis is not isolated fromthe AC power line. Use a transformer of adequate powerrating as this protects the technician from accidentsresulting in personal injury from electrical shocks. It will alsoprotect AC Adaptor from being damaged by accidentalshorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a shortcircuit is found, replace all parts which have beenoverheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices suchas insulation barriers, insulation papers shields are properlyinstalled.

5. After servicing, make the following leakage current checksto prevent the customer from being exposed to shockhazards.

3

2 Warning

2.1. Prevention of Electro Static Discharge (ESD) to ElectrostaticallySensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors andsemiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damagecaused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on yourbody by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such asaluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" cangenerate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Mostreplacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparableconductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as thebrushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)sufficient to damage an ES device).

4

2.2. Caution for AC Cord(VJA0940 type)

2.2.1. Information for your safety

IMPORTANT

Your attention is drawn to the fact that recording of pre-recorded tapes or discs or other published or broadcastmaterial may infringe copyright laws.

WARNING

To reduce the risk of fire or shock hazard, do not expose thisequipment to rain or moisture.

CAUTION

To reduce the risk of fire or shock hazard and annoyinginterference, use the recommended accessories only.

FOR YOUR SAFETY

DO NOT REMOVE THE OUTER COVER

To prevent electric shock, do not remove the cover. No userserviceable parts inside. Refer servicing to qualified servicepersonnel.

2.2.2. Caution for AC Mains Lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plugfor your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that thereplacement fuse has a rating of 5 amperes and it is approvedby ASTA or BSI to BS1362.

Check for the ASRA mark or the BSI mark on the body of thefuse.

If the plug contains a removable fuse cover you must ensurethat it is refitted when the fuse is replaced.

If you lose the fuse cover, the plug must not be used until areplacement cover is obtained.

A replacement fuse cover can be purchased from your localPanasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet inyour home then the fuse should be removed and the plug cutoff and disposed of safety.

There is a danger of severe electrical shock if the cut off plugis inserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code asshown below.

If in any doubt, please consult a qualified electrician.

2.2.2.1. Important

The wires in this mains lead are coloured in accordance withthe following code:

As the colours of the wires in the mains lead of this appliancemay not correspond with the coloured markings identifying theterminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to theterminal in the plug which is marked with the letter N orcoloured BLACK.

The wire which is coloured BROWN must be connected to theterminal in the plug which is marked with the letter L or colouredRED.

Under no circumstances should either of these wires beconnected to the earth terminal of the three pin plug, markedwith the letter E or the Earth Symbol.

2.2.2.2. Before use

Remove the Connector Cover as follows.

2.2.2.3. How to replace the Fuse

1. Remove the Fuse Cover with a screwdriver.

2. Replace the fuse and attach the Fuse cover.

5

2.3. How to Replace the Lithium BatteryThe lithium battery (CGR-F/202AW) is not supplied as a service part and must be replaced as part of the Side R Shaft Unit. (Referto "Disassembly and Assembly Instructions.")

NOTE:

This Lithium battery is a critical component. (Type No.: CGR-F/202AW Manufactured by Panasonic.) (Not supplied)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in equipment designed specifically for its use.

Replacement batteries must be of the same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

6

3 Service Navigation3.1. IntroductionThis service manual contains technical information which will allow service personnel´s to understand and service this model.Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original servicemanual.

Note 1:

1. VSK0561 is indicated on AC Adaptor used on the following models:

NV-GS88GK.

However, the AC Adaptor replacement part number is DE-974HC which should be used when ordering.

2. VSK0561 is indicated on AC Adaptor used in the following models:

NV-GS80E, NV-GS80EB, NV-GS80EE, NV-GS80EF, NV-GS80EG, NV-GS80EK, NV-GS80EP, NV-GS85EE, and NV-GS85GC.

However, the AC Adaptor replacement part number is DE-974GC which should be used when ordering.

Note 2:

1. This service manual does not contain the following information, because of the impossibility of servicing at component level.

a. Schematic Diagram, Block Diagram and P.C.B. layout of Main P.C.B.

b. Parts List for individual parts of Main P.C.B.

2. The following category are recycle module parts. Please send it to Central Repair Center.

a. *Main P.C.B. (LSEP8361P1/ LSEP8361Q1/ LSEP8361R1)

When a part replacement is required for repairing Main P.C.B., replace the assembly parts.

3.2. About Lead Free Solder (PbF)Distinction of PbF PCB:

PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB.

Caution:

· Pb free solder has a higher melting point than standard solder; Typically the melting point is 50-70°F (30-40°C) higher.

Please use a high temperature soldering iron. In case of the soldering iron with temperature control, please set it to700±20°F (370±10°C).

· Pb free solder will tend to splash when heated too high (about 1100°F/600°C).

When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat thesoldering points with the Pb free solder until it melts enough.

7

4 Specifications

8

5 Service Mode5.1. Error Display"PUSH THE RESET SWITCH" is displayed automatically on the EVF or the LCD Monitor when an undesirable condition hasoccurred.

Fig. 1

Note:

When "PUSH THE RESET SWITCH" is displayed repeatedly, service is required. Check the Error Code which is listed in theService Menu.

5.2. Service MenuWhen abnormal detection contents are confirmed, do the following operation. Automatic diagnosis code will be displayed. (ServiceMenu)

To enter the Service Menu

Push the [PHOTO SHOT], [JOYSTICK CONTROL LEFT] and [RECORDING START/STOP] simultaneously for 3 seconds (withno SD Card inserted).

Note:

If a tape or SD Card is inserted, the above operation will not work.

Fig. 2-1

9

To perform the factory setting

After repairing, perform this operation to clear the Mechanism lock code and Lens motor lock code.

1. Set to Service Menu.

2. Press [JOYSTICK CONTROL UP/DOWN] to select item [1].

3. Press [JOYSTICK CONTROL RIGHT] to display [NO/YES] screen.

4. Press [JOYSTICK CONTROL UP/DOWN] to select [YES].

5. Press [JOYSTICK CONTROL CENTER] to end.

To reset the Cylinder elapsed time

After replacing the Cylinder unit, perform this operation to clear the Cylinder elapsed time.






To confirm the error, lock code, or elapsed time






Fig. 2-2

To exit the Service Menu

Unplug the AC Cord.

10

6 Service Fixture & Tools

6.1. Service Fixture and Tools

11

12

6.2. Service Position

6.2.1. Extension Cables for Service Position

Using the following Extension Cables, place the unit as shown for check and service.

Note:

1. The LCD open/close Switch is for changing between LCD Display and EVF Display. When turning on EVF Display, close theLCD Shaft so that LCD open/close Switch stays ON.

2. To eject the Mechanism, hold down the Eject Switch on the Side L Operation Unit for a short time, or open the Cassette Coverof the Side L Operation Unit.

3. Use a grounded ESD wrist strap while disassembling the Lens portion.

4. Connect the F.P.C.s to the connectors, verifying the direction of F.P.C.s.

5. Use extreme care when plugging in or unplugging connectors.

13

Fig. 3

14

6.3. Removal/Installation of F.P.C.From Non ZIF (Zero InsertionForce) Connector

Removal/Installation of F.P.C. from the Non ZIF (ZeroInsertion Force) connector:

1. The Non ZIF connectors and the ZIF connectors are usedon the unit. And there are 2 types (Type A, Type B) of NonZIF connectors.

2. To remove the F.P.C. from the Non ZIF connector, use thePlier for Non ZIF Connector (LSVQ0028) to pull out theF.P.C. as shown. The same Plier for Non ZIF Connector(LSVQ0028) should also be used to install the F.P.C. to theNon ZIF Connector.

Fig. 4-1

3. Connect the F.P.C.s to the Non ZIF connectors, verifyingthe direction of F.P.C as shown.

Fig. 4-2

15

6.4. Method for Loading/Unloadingof Mechanism

CAUTION:

If loading does not start after DC Power Supply is applied,DO NOT continue to apply DC Power.

Apply +3 VDC Power Supply to the Loading Motor terminals.

Loading:

DC (-) to Portion "a," DC (+) to Portion "b"

Unloading:

DC (+) to Portion "a," DC (-) to Portion "b"

Fig. 5

6.5. EEPROM DataCAUTION:

Be sure to save the EEPROM data using PC-EVRAdjustment Program before service and adjustment inorder to make sure to avoid an accidental data loss, etc.using PC-EVR Adjustment Program by first.

16

6.6. Special NoteAll integrated circuits and many other semiconductor devicesare electrostatically sensitive and therefore require the specialhandlings techniques described under the"ELECTROSTATICALLY SENSITIVE (ES) DEVICES" sectionof this service manual.

17

7.1.1. DISASSEMBLY FLOWCHART

This flow chart indicates the disassembly steps of thecabinet parts and the P.C.Boards in order to gain access toitem (s) to be serviced. When reassembling, perform thestep (s) in the reverse order. Bend, route and dress thewires as they were originally.

Note:

1. When removing the cabinet, work with care so as not tobreak the Locking Tabs.

2. Place a cloth or some other soft material under the P.C.Boards or Unit to prevent damage.

3. When reinstalling, ensure that the connectors areconnected and electrical components have not beendamaged.

4. Do not supply power to the unit during disassembly andreassembly.

7 Disassembly and Assembly Instructions7.1. Cabinet Section

18

7.1.2. Disassembly Method

STEPNo.

Ref.No.

PART REMOVESectionNo.

NOTE

2Front Case Ass'y

A B C D E F

2

9

2(519), 3(537), FP6501

3(441), (24)

2(519), FP21,FP22, FP23, FP24, FP61

E10 7Main P.C.B.

5

EVF Unit

MAIN PARTS PORTION

Mechanism Chassis Ass'y

9-

6

Lens Ass'y

7

Battery Case Unit

How to read chart shown above:A: Order of Procedure steps.

When reassembling, perform steps(s) in reverse order.B: Ref No.C: Part to be removed or installed.D: Section No.E: Identification of part to be removed, unhooked, unlocked,

released, unplugged, unclamped, or unsoldered.

F: Refer to "Notes in chart."

7

12

26

2

1

1Bottom Unit1 6(519), (537)

3Side R Shaft Unit& LCD Ass'y

3

4

5

6

2(518), 3(519), FP811

1

1

1

1

1

-

-

-

8Side L OperationUnit

8 (537), 2(L-1)1

42(519), (537),FP91

1

2(537), FP31, FP71, FP72

2(519), FP11

3(404)= 3 Screws (404), 2(L-1) = 2 Looking Tabs (L-1)

19

A

B

C

D

E

F

G

H

1 2 3 4 5 6

1Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.

MAIN PARTS SECTION

2

519

710

26

Lens Ass'y

Front Case Ass'y

537

537

12

519

519

537

Side R Shaft Unit & LCD Ass'yFP61 FP23

FP21

FP31

FP81FP72 FP22

FP24

FP6501

518 518519

537

519

519

7

537

519

519 519 519519

519

519

519

519

519

24

441

441

441

537


519

-3

-4

-3

-7

-8

-7

-5

-2

-2

-1-1

537 -2

-1

537 -2

-1

-1-1

-1

-5

-3-3

-2

-4

-4

-3

-6

-6

FP71

FP91FP11

(L-1)

(L-1)

AB

CD

E

E

AB

CD

E10

20

STEPNo.

Ref.No.

PART REMOVE NOTE

A B C D E F

2 56 ----- -Front Case Unit

SectionNo.





22

10Front P.C.B.1 E30 5(537)2

FRONT CASE PORTION


21

A

B

C

D

E

F

G

H

1 2 3 4 5 6

2 FRONT AND BOTTOM CASE SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.537

537

537

537

537533

702

701

705

703

53

56

6

7

72

30

48

47

519

519

537

519

28

29

45

3246

519

E30

(NV-GS85EE-S/GC-S NV-GS88GK-S)




704(NV-GS85EE-S/GC-S, NV-GS88GK-S)

22

STEPNo.

Ref.No.

PART REMOVE NOTE

1

SectionNo.

A B C D E F

SIDE R SHAFT & LCD PORTION





SectionNo.

3

3

3

3

3

STEPNo.

Ref.No.

PART REMOVE NOTE

12

LCD Backlight P.C.B

LCD Case B

A B C D E F

3

5

4

4

3(L-4)-

3(L-2)

3 11LCD Case A33

2 3 FP8101 11Side R Shaft Unit

2(519), 8(L-1)

E40

35

34

38

31

(533), 3(L-3), FP8102

12LCD Panel Ass'y

12

LCD Shield Case

-----

-----

-----

-----

13Diffusion Sheet

31 42 ----- 13LCD Panel

5 40 13BEF Sheet

3

3

2 39 -----

-----

13Reflect Sheet

3 37 13Lead Light Panel

36 41 13BEF Sheet A

37 36 13Panel Holder Unit


23

A

B

C

D

E

F

G

H

1 2 3 4 5 6

3 SIDE R SHAFT UNIT AND LCD SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.

(L-2)

(L-4)

(L-3)

(L-3)(L-3)

(L-4)

(L-2)

(L-4)

(L-2)

519

519

533

E40

FP8101

FP8102

33

4236

39

37

38

31

40

44

41

35

34

A

A

B

B

LCD Panel Ass'y

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

24

STEPNo.

Ref.No.

PART REMOVE NOTE

2 14Filter Rubber

1 14CCD P.C.B

-----

E50

64

A B C D E F

SectionNo.

CCD & LENS PORTION

4

4

14Optical Filter3 -----63 4

STEPNo.

Ref.No.

PART REMOVE NOTE

3 15Focus Motor Unit

2 15Zoom Motor Unit

66

65

A B C D E F

SectionNo.





4

4

2(536)

2(538),Unsolder

2(538),Unsolder

1 -Lens Angle9 4 (533)

25

A

B

C

D

E

F

G

H

1 2 3 4 5 6

4 CCD AND LENS SECTION

LUBRICATION POINTSWhen the marked parts are replaced, apply the recommended lubricants or adhesive for better maintenance of the unit.

Mark Kind of LubricantGrease Available from Factroy LSUQ0050

Availability Part Number

Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.

Solder

66

65

533

533

538

538

538538

63

9

64

61

536

536

533

Solder

Lubrication Points

Lubrication Points

E50

26

(519), 2(L-2)

EVF PORTION

STEPNo.

Ref.No.

PART REMOVE NOTE

A B C D E F

SectionNo.

2(519), 2(L-1)

2(533)

1 16EVF Earth Plate15 5

3

2

16EVF Spring14 5

16EVF Base Frame FP890113 5

4 16EVF Backlight F.P.C. -----17 5

STEPNo.

Ref.No.

PART REMOVE NOTE

1

A B C D E FHow to read chart shown above:A: Order of Procedure steps.




SectionNo.

17Eye Cap18 5

3

2

18Eye Sight Lever

EVF Lens Unit

-----22 5

18-----23 5


27

A

B

C

D

E

F

G

H

1 2 3 4 5 6

5 EVF SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly/Assembly Procedures" section.

(L-2)

(L-1)(L-1)

(L-2)

13

17

14

23

20

18

22

12

21

15

519

519

533

533

519

FP8901(not supplied)

28

Notes in chart3. Removal of Side R Shaft Unit & LCD Ass'y

1) Remove the 5 Screws (518, 519).2) Disconnect the F.P.C. from Connector FP81.

Installation of Side R Shaft Unit & LCD Ass'yTake care not to damage the F.P.C.1) Connect the F.P.C. to Connector FP81.2) Insert Pin A of Lens into Hole A, and Pin B of Side R Shaft

Unit into Hole B.

Side R ShaftUnit & LCD Ass'y

Side R Shaft Unit

FP81

Pin A

Hole B

LCD Shaft F.P.C.

Pin B

Hole A

518519

518

519

519

Fig. D3

1. Removal of Bottom Unit1) Release the Hand Strap.2) Remove the 7 Screws (519, 537).

Bottom Unit

519

519

519

519

519

519

537

ReleaseHand Strap

<Bottom View>Fig. D1

2. Removal of Front Case Ass'y1) Open the LCD and the Jack Cover and remove the 5

Screws (519, 537).2) Pull and slide out the Front Case Ass'y carefully and

disconnect the F.P.C. from Connector FP6501.

Front Case Ass'y

FP6501

Open LCD

Slide

Open Jack Cover

519

537

537537

519

<Bottom View>

Fig. D2

29

4. Installation of EVF Unit1) Connect the F.P.C. to Connector FP91.2) Insert EVF Earth Plate into the gap, and tighten the 3

Screws (519, 537).

537

519

519EVF Earth Plate

FP91

EVF Unit

Fig. D4

5. Installation of Lens Ass'yTake care not to damage the motor leads and the F.P.C.s.1) Install the Lens Ass'y with the 2 pins, and tighten the 2

Screws (537).2) Connect the F.P.C.s to Connectors FP31, FP71, and

FP72.

FP71

FP72

FP31

Pin

Pin

Lens Ass'y

Motorleads

537

537

Fig. D5

6. Removal of Battery Case Unit1) Open the Cassette Cover to remove the 2 Screws

(519).2) Disconnect the Battery Case F.P.C. from Connector

FP11.

519

519

Battery Case Unit

Open Cassette Cover

FP11Battery Case F.P.C.

Fig. D6

30

7. Installation of Main P.C.B.Take care not to damage the F.P.C.s.1) Connect the F.P.C.s to the connectors on the Main

P.C.B., verifying that the direction of the Flexible Cablesis correct. Refer to "Removal/Installation of F.P.C. FromNon ZIF (Zero Insertion Force) Connector."

2) Tighten the 2 Screws (519).3) After installing the Main P.C.B, confirm the F.P.C.s are

positioned as shown.

519519

Main P.C.B.

Capstan F.P.C.

Side L F.P.C.

Head Amp F.P.C.

Mechanism F.P.C.

Cylinder F.P.C.

Fig. D7

8. Removal of Side L Operation Unit1) Remove the Screw (537).2) Pull off the Mechanism Ass'y while releasing the 2

Locking Tabs (L-1) and the boss.

537

(L-1)

(L-1)

Pull Mechanism Ass'y Boss

Side L Operation UnitFig. D8

9. Replacement of Mechanism Chassis Ass'yWhen replacing the Main Chassis Ass'y or the CylinderUnit, be sure to perform the Envelope Output Adjustment.Refer to "ENVELOPE OUTPUT ADJUSTMENT" inMechanical Adjustment.

Mechanism Chassis Ass'y Handling CautionWhen servicing the Mechanism Chassis Ass'y without theCassette Up Unit, do not handle the Sub Chassis of theMechanism Chassis Ass'y.

Sub Chassis

Sub Chassis

Sub Chassis

Mechanism Chassis Ass'y(with Cassette Up Unit)

Fig. D9

31

10. Installation of Front P.C.B.Install the Front P.C.B. with the 5 bosses, and tighten the5 Screws (537).

Boss

Boss

Boss

Boss

Boss

Front P.C.B.

537

537537

537

537

Fig. D10

11. Removal of Side R Shaft Case Unit and LCD Case ATake care not to damage the F.P.C.1) Open and rotate the LCD to access the 2 Screws (519).2) Release the 8 Locking Tabs (L-1) and remove the LCD

Case A.3) Disconnect the F.P.C. from Connector FP8101.4) Remove the Side R Shaft Unit.

Side R Shaft Unit

LCD (Ass'y)

FP8101

LCD Case A

LCD Shaft F.P.C.

Rotate to access

519

519

(L-1)(L-1)

(L-1)

Fig. D11

12. Installation of LCD Backlight P.C.B., LCD Panel Ass'y,LCD Shield Case Unit and LCD Case BUse extreme care regarding LEDs when handling the LCDBacklight P.C.B.Install in order shown below.1) Install the LCD Panel Ass'y onto the LCD Shield Case

Unit with the 3 Locking Tabs (L-4) while carefullybending the LCD F.P.C. at its base so as not to damageit.

2) Install the LCD Backlight P.C.B. onto the LCD PanelAss'y with the 3 Locking Tabs (L-3).

3) Install the LCD Case B with the 3 Locking Tabs (L-2).4) Tighten the Screw (533) while keeping the LCD

Backlight P.C.B. pressed toward the left. Then, connectthe F.P.C. to Connector FP8102.

LCDShield Case

LCD Panel Ass'y

LCD F.P.C.

LCD Backlight P.C.B.

LCD Case B

(L-2)

(L-2)

(L-3)

(L-4)

(L-4)

(L-4)

(L-3)

(L-3)

FP8102

LEDs

Press533

(L-2)Bend

Fig. D12

32

Panel Holder Unit

LCD Panel

Reflect Sheet

Adhesive tape

Adhesive tape

Portion A

Portions B

Adhesive tape

Lead Light Panel

(stripe)

(stripe)

BEF Sheet A

BEF Sheet

Diffusion Sheet

(white)

Fig. D13-2

13. Installation of LCD Panel, Reflect Sheet, Lead LightPanel, Diffusion Sheet, BEF Sheet, BEF Sheet A andPanel Holder Unita. When replacing the LCD Panel, the Diffusion Sheet,

the BEF Sheet and the BEF Sheet A, make sure toremove the Protection Sheets.To distinguish Sheets from attached ProtectionSheet:- A blue Protection Sheet is affixed to both faces of the

Diffusion Sheet.- A green Protection Sheet is affixed to both faces of the

BEF Sheet.- A green Protection Sheet is affixed to both faces of the

BEF Sheet A.

(green)

(blue)

(green)

Protection Sheet

Protection Sheet

Protection Sheet BEF Sheet A

BEF Sheet

Diffusion Sheet

b. Use extreme care when handling the LCD Panel, theReflect Sheet, the Lead Light Panel, the DiffusionSheet, the BEF Sheet and the BEF Sheet A to avoiddamage, dust, and spots (especially fingerprints, etc.)

Install in order shown below.1) Install in order: the BEF Sheet A, BEF Sheet and

Diffusion Sheet while fitting the corners of each sheetinto the corners of the Panel Holder Unit.

2) Install the Lead Light Panel while fitting the corners intothe corners of the Panel Holder Unit.

3) Place the Reflect Sheet so it is aligned with Portion Aof the Panel Holder Unit, then install it using theadhesive tape portions of the Reflect Sheet.

Reflect Sheet

Do not touch the surface of Lead Light Panel.

Panel Holder Unit

Adhesive tape

Adhesive tape

Fig. D13-1

4) Install the LCD Panel with adhesive tape so it is alignedwith Portions B of the Panel Holder Unit.

33

14. Removal of CCD P.C.B., Filter Rubber and Optical FilterCAUTION:1) When removing the CCD P.C.B., take care that the

Optical Filter does not fall out.2) Use extreme caution when removing the CCD P.C.B.

as it is easily damaged by static electricity. Use a WristStrap while removing and installing.

3) Do not touch the CCD window surface.Installation of CCD P.C.B., Filter Rubber and OpticalFilterInstall in order shown below.1) Install the Optical Filter, taking care the direction is

correct.Note: Make sure that no dust gets on the Optical Filteror in the Lens Unit. Clean the Optical Filter with lenscleaning paper dampened with lens cleaner ifnecessary.

2) Install the Filter Rubber on the Optical Filter, taking carethe direction is correct.Note: Make sure that no dust gets on the FilterRubber.

3) Install the CCD P.C.B. into the Lens Unit. Then, tightenthe 2 Screws (536).Note: Do not touch the Lens Surface. Clean the surfacewith lens cleaning paper dampened with lens cleanerif necessary.

15. Installation of Zoom Motor Unit/Focus Motor UnitInstall the Zoom Motor Unit/Focus Motor Unit so that theShaft of the Zoom Motor Unit/Focus Motor Unit is set in theHolder.

Focus Motor Unit

Zoom Motor Unit

Shaft

Shaft

Holder

Holder

Boss

Boss

Boss

Boss Boss

Fig. D14

16. Installation of EVF Backlight F.P.C., EVF Spring, EVFBase Frame and EVF Earth PlateTake care not to damage the F.P.C. and the Switch.1) Insert the EVF Backlight F.P.C. into the slot and secure

it with the 2 pins. Then, pass it through the hole.2) Install the EVF Sping with the 2 Locking Tabs (L-2), and

tighten the Screw (519).3) Connect the EVF Backlight F.P.C. to Connector FP8901,

and install the EVF Base Frame so that the ribs areinserted into the slots.

4) Install the EVF Earth Plate with the boss, the pin, andthe 2 Locking Tabs (L-1). Then, tighten the 2 Screws(519).

5) After installing, verify the EVF moves correctly.

EVF Backlight F.P.C.

<Bottom View>

Pins

519

519

519

EVF Standby Switch

Pass

FP8901

Rib

Slot

Boss

(L-1)

(L-1)

Pin

Ribs

(L-2)

SlotHole

EVF Base Frame

EVF Earth Plate

(L-2)

EVF Spring

Fig. D15

34

17. Removal of Eye CapRemove the Eye Cap after removing the 2 Screws (533).

18. Handling Cautions of EVF Lens UnitUse extreme care when handling the EVF Lens Unit toavoid damage, dust, and spots (especially fingerprints,etc.)

Installation of EVF Lens Unit, Eye Sight Lever1) Install the Eye Sight Lever into the EVF Case hole in the

direction shown.2) Install the EVF Lens Unit into the EVF Case.3) After installing, verify the Eye Sight Lever and the EVF

Lens Unit work together correctly.

EVF Lens Unit

Eye Sight Lever

Hole

EVF Case

Rotate

Fig. D16

35

7.2. Mechanism Section

No. Item / Part Fig. Removal (Screw, Connector, Flex. & Other)

1

2

Cassette Up Unit

Cylinder Unit

Fig. M1Fig. M2Fig. M3

Move the mechanism into Eject position (For Battery)4-Tabs1-Screw (A)3-Screw (B)

Battery

<Eject Position>

Tab

Hooking

Tab

Cassette Up Unit

Tab

Hooking

Tab

Fig. M1

Fig. M2

36

Cylinder Unit

Screw (A)

Screws (B)

Fig. M3

37

8.1. Mechanical Adjustment

8 Measurements and Adjustments

8.1.1. ENVELOPE OUTPUT ADJUSTMENT

When replacing the Main Chassis Unit or the Cylinder Unit, be sure to perform the Envelope Output Adjustment as shown below.

1. Remove the Bottom Case Unit. (Refer to "Disassembly and Assembly Instructions")

2. Connect the oscilloscope to TP3922 (Envelope) and TP3921 (HID) on the Main P.C.B.

3. Play back the Color Bar Standard Tape (VFM3110EDS). "Envelope" and "HID" signal will be output.

4. Adjust the S1 post by turning the top of post with Post Height Adjustment Fixture (VFK1899) so that the left half of envelopesignal becomes as flat as possible.

5. Adjust the T1 post by turning the top of post with Post Height Adjustment Fixture (VFK1899) so that the right half of envelopesignal becomes as flat as possible.

Fig. E1-1

38

Fig. E1-2

39

8.2. Electrical Adjustment

8.2.1. Initial Guideline

The table below shows which adjustments are necessary according to the unit parts and individual parts to be replaced. Make sureto perform these adjustments shown below as necessary.

40

8.2.2. Installation of USB-SERIAL driver

Execute the "Setup.exe" file in "ComMass" folder by doubleclicking to install the USB-SERIAL driver.

8.2.3. COM Mode

If a Disc or SD Card is inserted, remove before operation.

To enter the PC connection (COM) mode, push the [PHOTOSHOT], [RECORDING START/STOP] and [JOYSTICKCONTROL UP] simultaneously for 3 seconds with the USBCable disconnected.

8.2.4. SET UP OF PC-EVR ADJUSTMENTPROGRAM

1. Turn on the PC and install the PC-EVR AdjustmentProgram into the PC.

2. Execute the "kdv2007.exe" file by double clicking to start upthe PC-EVR Adjustment Program.

The main menu will be displayed.

3. Select the appropriate model.

4. Turn on the camcorder and set to PC connection (COM)mode. Then click "Start".

5. When the communication is complete, the following dialogwill appear.

Click "Yes," and "Save" to save the EEPROM data.

Fig. E2-2

6. When EEPROM data has been saved, the menu willappear.

To perform each adjustment, display the adjustment menuby selecting from "Camera Adjust" or "VCR Adjust" andselect each adjustment item.

Fig. E2-3

Note:

The adjusted data is stored in the EEPROM IC aftereach adjustment.

7. After adjustment, to close the software, select "Exit" in theFile menu or close the window.

Fig. E2-4

8. To release the PC connection (COM) mode, push the[PHOTO SHOT], [RECORDING START/STOP] an[JOYSTICK CONTROL UP] simultaneously for 3 secondswith the USB Cable disconnected.

41

9 Maintenance9.1. Cleaning Lens, Viewfinder and LCD PanelDo not touch the surface of the lens, Viewfinder and LCD Panel with your hand.

When cleaning the lens, use air-blower to blow off the dust.

When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and gently wipe the surface.

Note:

Lens cleaning paper and lens cleaner are available at camera shops, etc.

9.2. How to use the DVC Head Cleaning Tape / VFK1451Please use the cleaning tape as described below.

42

10 Block Diagrams

NV-GS80EG/EF/E/EP/EB/EK/EE, NV-GS85GC/EE, NV-GS88GK

OVERALL BLOCK DIAGRAM

OVERALL BLOCK DIAGRAM

CAMERA DATA (10 BIT)

SERIAL DATA/CLOCK

CAMERA VD/HD

IC3001

IC6001

IC3201

IC5001

IC2001

IC302

IC3301

IC6701

IC6003

IC6005

IC1001, 1002, ETC

CCD DRIVE TIMING GENERATOR

CCD

FOCUS/ZOOM MOTOR DRIVE/OIS DRIVE/IRIS/HALL AMP CONTROL

IC601

MIC

IC701

IC4801

IC7801,IC7802

LENS UNIT

IC303

CCD P.C.B.

SIDE R SHAFT UNIT

SPEAKER

SD CARD SLOT

DV JACK

USB JACK

AVJACK

BATTERY CASE UNIT

MAIN P.C.B.

ECM UNIT

FRONT P.C.B.

CAMERA SIGNAL PROCESS

CAMERA DIGITAL SIGNAL PROCESS

D/A

AUDIO SIGNAL PROCESS

SD I/F

USB I/F

USB I/F

IEEE1394 I/F

IC401

AUDIO I/F

EEPROM

RESET

IC6004

TIMER

POWERSUPPLYCIRCUIT

SYSTEM MICROCONTROLLER

SUB MICROCONTROLLER

IC3301

REC DATA

PB DATA

REC DATA

CAP SPEED ERROR

MODE SW POSITION 1-3SAFETY TAB ON(L)TAKEUP REEL SENSORSUPPLY REEL SENSOR

KEY DATA

PHOTO SW

ZOOM SW

POWER SW

POWER LED ON(L)

STANDBY LED ON(L)

SUPPLY PHOTO TR

TAKEUP PHOTO TR

SENSOR LED ON(H)

CASSETTE DOWN(L)

MIC SERIAL DATA/CLOCK

CYL SPEED ERROR

CAP FG

CYL FG

LOADING MOTORREVERSE/FORWARD

DBR (4 BIT)PB DATA

VIDEOSIGNALPROCESS

IR CIRCUIT

ACCESS LED

BATTERY

POWER LED

OPERATION BUTTON

ZOOM SW

STANDBY LED

SENSOR LED

MIC

CASETTE DOWN SW

SUPPLY PHOTO TR

TAKEUP PHOTO TR

MODE SELECT SW

SAFETY TAB SW

LOADING MOTOR

TAKEUP REEL SENSOR

SUPPLY REEL SENSOR

REMOTE SENSOR

GYRO

LED LIGHT

BATTERYTERMINAL

DC JACK

DVFORMATTINGINTERFACE

FORMATTING/EQUALIZER

CAPSTANMOTOR DRIVECYLINDERMOTOR DRIVE

IC8001

LCDSIGNALPROCESS

LCD BACKLIGHT P.C.B.SIDE R SHAFT UNIT

CYLINDER UNIT

SIDE L OPERATION UNIT

MAIN CHASSIS UNITMECHANISM FPC

CAPSTAN UNIT

EVF UNIT

LCD PANEL

EVF LCD PANEL

HEAD AMP

SDCARD

DRIVE

IC2002

LED DRIVE

+5V

FP11

FJ4801

FP41

FP81

FP72

FP91

FP81

FP24

FP22

FP23

FP21

FP61

FP8102FP8101

FP31

FP6501

P1203SERIAL DATA/CLOCK

LIGHT ON(H)

IR DET

RESET(L)

OIS MICOM RESET

REMOCON

ACCESS LED ON(L)

HALL BIAS/PWM BIAS/HALL AMP GAIN CONTROL

SBA SIF SERIAL DATA/CLOCK

MIC AUDIO

GYRO X, GYRO Y

OIS DRIVEDATA/CLOCK

SP AUDIOAUDIO

MIC AUDIO

CCD

ALC CONTROL/IRIS OPEN/IRIS CLOSE

H1/H2//RESET PULSE

LENS DRIVE DATA/CLOCK

S-VIDEO-YS-VIDEO-C

V1-V4/CH1/CH2 PULSE

AUDIOVIDEO

VIDEO

PB AUDIO DATA

REC AUDIO DATA

LCD-RLCD-GLCD-B

EVF-REVF-GEVF-B

+3.3VUNREG/NOREG+3V+2.5V+1.8V+1.5V-6.5V+8.5V+12VCAP VMCYL VM LED DRIVE

LED DRIVE

LED DRIVE

D/A

LOADINGMOTOR DRIVE

M

LCD/EVF SERIAL DATA/CLOCK

PHOTO SW

FP8902FP8901

EVF BACKLIGHTEVF FPC

RESET SW

POWER SW

(WITH USB2.0 HIGH-SPEED)

(WITHOUT USB2.0 HIGH-SPEED)

(WITH LED LIGHT)

(WITH IR RECEIVER)

(WITH SD SLOT)

OIS HANDSHAKE

OIS SERIAL DATA/CLOCK

43

44

11 Schematic Diagrams11.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT NOTES

1. Important safety notice

Components identified by the sign have special

characteristics important for safety. When replacing anyof these components, use only the specified parts.

2. Do not use the part numbers shown on these drawings forordering.The correct part number and part value is shown in theparts list, and may be slightly different or amended sincethis drawing was prepared.

3. Use only original replacement parts:To maintain original function and reliability of repairedunits, use only original replacement parts which are listedwith their part numbers in the parts list section of theservice manual.

4. Parts different in shape or size may be used.However, only interchangeable parts will be supplied asservice replacement parts.

5. Test point information

: Test point with no test pin.

Schematic Diagram Notes

1. Indication for Zener Voltage of Zener DiodesThe Zener Voltages of Zener Diodes are indicated assuch on Schematic Diagrams.

Example:(6.2V)......Zener Voltage

2. How to identify ConnectorsEach connector is labeled with a Connector No. and PinNo. Indicating what it is connected to (its counter part).Use the interconnection schematic diagram to find theconnection between associated connectors.

Example: The connections between two P.C.B.s are shown below.

POWER SUPPLYP.C.B. MAIN P.C.B.

The Number of pins of the Connector.

Connector No.on Main P.C.B.

P1503 P3004(10 Pins)

Ref. No. of the connection parts such as lead cable, flexible cable which is supplied as a replacement parts.

244

3. Parts marked "PT" are not used in any models includedin this service model.

Example: 100PPT

C6011 R6097PTPT

C6011

Signal Waveform NoteHow to read Signal Waveform

0.5 V 20 µs

V1 1.0 Vp-p Volts/Div

Time/Div

V1:Peak to Peak

3

1

1

2

2

3

Voltage Chart NoteVoltage Measurement

a. Color bar signal in SP mode.b. ---:Unmeasurable or not necessary to measure.

Circuit Board Layout NoteCircuit Board Layouts show components installed forvarious models.For proper parts content for the model you are servicing,please refer to the schematic diagram and parts list.

NOTE:Circuit Board Layouts include components which are not used.

SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT NOTESNV-GS80EG/EF/E/EP/EB/EK, NV-GS85GC/EE, NV-GS88GK

Model Number IndicationModel numbers are indicated without "NV-GS."

45

11.2. FRONT SCHEMATIC DIAGRAM

NOTE:FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES,REFER TO BEGINNING OF SCHEMATIC SECTION.

NOTE:PARTS MARKED "PT" ARE NOT USED.

NOTE: For placing a purchase order of the parts, be sure to use the part number listed in the parts list. Do not use the part number on this diagram.

NV-GS80EG/EF/E/EP/EB/EK, NV-GS85GC/EE, NV-GS88GK

FRONT SCHEMATIC DIAGRAM

LSJB8363FRONT SCHEMATIC DIAGRAM

FJ4801

3ECM_L

2A_GND

1ECM_R

R48103900[D] C4801

1[KB]

C481

1PT

C48080.027[KB]

R4805120K

R480

933

K

C48100.027[KB]

C48098200P

R480

247

00

C481222/6.3V

R480633K

R480

433

KR4

803

22K

C480

7PT

C48060.027[KB]

C48048200P

C48050.027[KB]

R480

812

0K

C48021[KB]

R4811PT

R48073900[D]

IC4801C0ABBB000369

1234

5 6 7 8

C65040.1[KB]

10MR6504

D6503B0ADEJ000038

D6504B3GA00000062

3R3MR6505 C6505

0.22[KB]

Q6501B1ABCF000098

10KR6507

R6506180K

C65030.22[KB]

C65020.1

R650156

C650110/6.3V R6503

100K

R650268K

R6509

1K

Q43052SB1218ARL

R43075600[D]

R4308470[D]

C43011[KB]

R430633K[D]

Q43022SD1819ARL

R430147[D]

Q4306UNR9112J08

Q4307UNR9213J08

U6501B3RAB0000064

1 2 3

C480

310

[KB]

D4301B3AFB0000126

R430247[D]

R43054700[D]

IC7801L2ES00000016

1VREF

4OUT

2

3

IC7802L2ES00000017

1VREF

4OUT

2

3

L7801

10U

C780110[KB]

C780210[KB]

C71024700P[KB]

3900 R7104

JK7101A/V JACK

1

5

3

2

4

D7101D4ED1120A005

C71014700P[KB]

J0JBC0000027R7103

R7105PT

R7101J0JBC0000027

J0JBC0000027R7102

TP7801

TP7802

TP7803

TP7804

C780322/6.3V

C780422/6.3V

3900R7801

3900R7802

3300R7803

3300R7804

0.015[KB]C7805

0.015[KB]C7806

0.015[KB]C7807

0.015[KB]C7808

IC7803C0ABHA000078

1

X_O

UT

2

X_IN

-

3

X_IN

+

4

GND

5

Y_IN

+

6

Y_IN

-

7Y_

OUT

8

VDD1K

R7805

1K

R7806

10KR7807

FP6501

22212019181716151413121110987654321

C780910[KB]

C781010[KB]

C781110[KB]

C781210[KB]

390KR7808

390KR7809

4700R7810

4700

R7811

PTR7812

PTR7813

270KR7814

270KR7815

2200P[KB]C7813

2200P[KB]C7814

TP7805

TP7806

C78151[KB]

Q65022SB1218AHL

R43032R2

D4303B0BC6R200019

D4302B0BC6R200019

XP0450100LQ7801

1

62

4

35

Q48012SD2216J08

ECM_R

ECM_L

Q43012SD1819ARL

D4803B0ACCJ000027

D4804B0ACCJ000027

[1608]

[Y]

[SSMINI]

[1608]

[1608]

[Y]

[1608]

LED_LIGHT

[1608][1608]

[1608]

[1608]

[1608][1608]

[1608]

[1608][1608]

[1608]

[1608]

[1608]

[SMINI][SMINI]

[1608]

[1608]

[1608]

[1608]

[2012]

[1608]

GND

VIDEO

[1608]

AR

AL

PLUG_L

[1608]

[Y]

[Y]

(GYRO X)

(GYRO Y)

[2012]

[2012]

[2012]

[2012]

[2012]

[XREF]

[YREF]

[GYRO_Y]

[GYRO_X]

[1608] [1608]

[1608] [1608]

[1608] [1608]

[1608] [1608]

[1608]

[1608][1608]

[1608]

[1608]

[1608]

[1608]

[1608]

[1608]

[1608]

[1608]

[1608][1608]

LIGHT_REG

PLUGIN_L

A_M_OUT_L

IR_GND

IRDETIR-REMOCON

LIGHT_ON_HLIGHT_REG

GYRO_Y

AUDIO_R

D_GND

IR_GND

D_GND

AUDIO_L

VIDEO_OUT

REGD+3V

D_GND

D_GND

GYRO_X

OIS_SENS_SW

A_M_OUT_R

REGA+5V

[1608]

ECM UNIT+5VREGULATOR

SWITCHINGLIGHT ON-ON

SWITCHINGLIGHT ON-ON

(LED DRIVE)

C

A

B

31 42

(SWITCHING)

(SWITCHING)

(OP AMP)

(SWITCHING)

(OP AMP)

TO MAIN P.C.B.FP41

[1608]

[2012]

(LED DRIVE)

(LED DRIVE)

INFRAREDRECEIVERUNIT

D

5 6

REC AUDIO SIGNALPB VIDEO SIGNALREC VIDEO SIGNAL PB AUDIO SIGNAL

LED LIGHT

IR SENSOR

85GC/EE, 88GK

PT

46

11.3. LCD BACKLIGHT SCHEMATIC DIAGRAM





LCD BACKLIGHT SCHEMATIC DIAGRAM

LSJB8367LCD BACKLIGHT SCHEMATIC DIAGRAM

2 NOTE:ALL INDIVIDUAL PARTS EXCEPT D8102, D8104, D8107, D8109 AND D8111ON LCD BACKLIGHT P.C.B. ARE SUPPLIED AS REPLACEMENT PARTS.WHEN SERVICING THESE PARTS, REPLACE LCD BACKLIGHT P.C.B.INSTEAD OF INDIVIDUAL PARTS.

FP8102

23 CS22 VST21 VCK20 EN19 DWN18 VDD17 VSS16 NRW215 VSSG

14 XSTBY13 PCG12 HST11 REF10 TEST19 NRW18 HCK27 HCK16 PSIG5 G4 R3 B2 RGT1 TEST2

24 COM1

2SC6

054J

0LQ

8104

PTD810

5

PTD810

3

PTD810

6

2SC6

054J

0LQ

8101

PTD810

8

27[D]R8110

27[D]R8112

2SC6

054J

0LQ

8102

2SC6

054J

0LQ

8105

PTD811

0

2SC6

054J

0LQ

8108

27[D]R8119 27[D]

R8124

100UL8101

270[D]R8102

270[D]R8105270[D]R8106

47K

R812

3

5600

[D]

R811

6

*

0R810

3

47K[

D]R8

135

2SA2174J0LQ8112

10K[

D]R8

1361[KB]

C8116PT

R813

3

1[KB]C8113

Q8109PT

PTR812

9

PTR8130 PT

R8134

PTC810

2

PTC810

3

39P

C810

4

39P

C810

5

39P

C810

6

D811

3M

AZ80

560M

L

R810727[D]

Q81132SA2174J0L

R812

610

0K

C81122R2[KB]

C810

94R

7[KB

] Q81072SA2174J0L

R8122PT

R811

50

R811456K[D]

C8110PT

C810

71[

KB]

D810

1MAZ

8062

0ML

PTC8

101

R81271K

0R8

143

PTR814

4

0.1[

KB]

C811

1

PTC810

8

FP8103 PT

23 STV22 CKV21 OEV20 CSV19 OEVE18 FR17 VCSH16 VCSH15 R

14 G13 B12 VSS11 VSS10 STH9 CKH18 CKH27 SB6 CSH5 VDD4 PCG3 VREF2 VVSS1 VCOM

24 VCOM

PTR813

8

PTC8

117

PTC811

8

PTR814

2

PTR814

1

PTC8

119PTR8

139

PTR8140

PTD811

2

NSSW020BT-P1D8111

NSSW020BT-P1D8109 R8

118

PT

0R8113

D8107NSSW020BT-P1

D8102NSSW020BT-P1

PTR810

9

0R8108

0R8145

PTR814

6

* PTC8

115

D8104NSSW020BT-P1

PTR8148

PT

R8149FP8101

22212019181716151413121110987654321

PTR8150

PTR8151

PTR8152

0R8153

0R8154

0R8155

PTQ8114

PTQ8115

PTQ8116

PTR8156 PT

R8157PTR8158

PTR8159

PTR8160

PTC8120

PTQ81

03

PTR8111

LCD_EN

LCD_G

LCD_COM/LCD_OEVE

LCD_WIDE

LCD_BL_+5V

LCD_VST

D_GNDBL_CONT

LCD_R

LCD_HCK2LCD_HCK1

LCD_BLCD_HST

LCD_BL_+5V

LCD_PSIG/LCD_VCSH

LCD_R/L

LCD_XSTB/LCD_FR

D_GND

LCD_PCG

LCD_U/D

LCD_+8.5V

LCD_VCK

(DRIVE)

(DRIVE)

(LED DRIVE)

BACKLIGHTBACKLIGHT BACKLIGHT BACKLIGHT BACKLIGHT

(LED

DRI

VE)

BACKLIGHTDRIVE

(TO LCD SW)

LCD PANELPB VIDEO SIGNALREC VIDEO SIGNAL

B

A

C

31 42 5

(LED

DRI

VE)

(LED

DRI

VE)

(LED

DRI

VE)

(LED

DRI

VE)

(LED

DRI

VE)

47

11.4. EVF BACKLIGHT / EVF FPC / BATTERY CASE SCHEMATIC DIAGRAMS





EVF BACKLIGHT SCHEMATIC DIAGRAMEVF FPC SCHEMATIC DIAGRAM

BATTERY CASE SCHEMATIC DIAGRAM

EVF FPC SCHEMATIC DIAGRAM“FOR REFERENCE ONLY”

EVF BACKLIGHT SCHEMATIC DIAGRAM

“FOR REFERENCE ONLY”

BATTERY CASE SCHEMATIC DIAGRAM

“FOR REFERENCE ONLY” NOTE:BATTERY CASE UNIT IS NOT SERVICEABLE AND ISSUPPLIED AS A UNIT ONLY FOR REPLACEMENT.

L1201MPZ2012S331AT

FL1201PT

1 4

2 3

P1203

121110987654321

L1202MPZ2012S331AT

JK1201

+

-

DC JACK

D

T

BATTREYTERMINAL

T

+

-

+

D

-

[3225]

GNDGNDGNDGNDGND

BATT_DETNC

UNREGUNREGUNREGUNREGUNREG

TO MAIN P.C.B. FP11

A

1 2

NOTE:EVF BACKLIGHT IS NOT SERVICEABLE AND ISSUPPLIED AS A UNIT ONLY FOR REPLACEMENT.

NOTE:EVF STANDBY SWITCH (SW9201) IS NOT SERVICEABLE AND ISSUPPLIED AS A EVF FPC FOR REPLACEMENT.

1[KB]C8903

MAZ80470MLD8902

1[KB]C8902

B3AFB0000129D8901

R8902PT

4700R8901

FP8901

16151413121110987654321

FP8902

181716151413121110987654321

D8903MA3S13300L

PTR8907

PTD8904

2SC6054J0LQ8901

100[D]R8903

STH

CSVENB

CKH2

CKV

NC

DSD

VDD

DSG

COM

VBB

VSSCKH1

STV

EVF_VSS

EVF_ENBEVF_DSD

EVF_G

EVF_VDD

EVF_STV

EVF_STHEVF_VSS

EVF_CKV

EVF_BL_+5V

EVF_CKH2

EVF_VCOM

EVF_DSG

EVF_CKH1

EVF_B

EVF_R

BRGCSH

(MAZ80620ML)

(LED DRIVE)

BACKLIGHT

TO EVF FPC

PB VIDEO SIGNALREC VIDEO SIGNAL

EVF LCD PANELB

A

1 2 3

ESE18L62DSW9201

EVF STANDBY

181716151413121110987654321

16151413121110987654321

EVF_ENBEVF_STV

EVF_BL_+5V

EVF_CKH1

EVF_DSD

EVF_STH

EVF_CKH2

EVF_VCOM

EVF_VDD

EVF_CKV

EVF_DSGEVF_B

EVF_G

EVF_R

EVF_VSSEVF_VSS

EVF_G

EVF_STV

EVF_R

EVF_DSD

EVF_BL_+5V

EVF_CKV

EVF_SLIDE_SW

EVF_STH

EVF_CKH1

NC(EVF_WIDE)

EVF_ENB

EVF_VSS

EVF_VDDEVF_B

EVF_VCOM

EVF_DSG

EVF_CKH2

EVF_VSS

TO MAIN P.C.B.FP91

TO EVF BACKLIGHTFP8901

PB VIDEO SIGNALREC VIDEO SIGNALB

A

1 2 3

48

11.5. CCD / SIDE L OPERATION / LCD SW SCHEMATIC DIAGRAMS





CCD SCHEMATIC DIAGRAM LCD SW SCHEMATIC DIAGRAM“FOR REFERENCE ONLY”

CCD SCHEMATIC DIAGRAMSIDE L OPERATION SCHEMATIC DIAGRAM

SIDE R SHAFT SCHEMATIC DIAGRAM

SIDE L OPERATION SCHEMATIC DIAGRAM“FOR REFERENCE ONLY”

“FOR REFERENCE ONLY” NOTE:CCD P.C.B. IS NOT SERVICEABLE AND ISSUPPLIED AS A UNIT ONLY FOR REPLACEMENT.

NOTE:LCD SW IS NOT SERVICEABLE AND ISSUPPLIED AS A UNIT ONLY FOR REPLACEMENT.

NOTE:SIDE L OPERATION UNIT IS NOT SERVICEABLE AND ISSUPPLIED AS A UNIT ONLY FOR REPLACEMENT.

Q6012SC3931

R6015600

IC601

1

V4

2

V3

3

V2

4

V1

5

GND

6

SBSW

7

CCDO

UT

8

VDD

9RE

SET

10

SUB

11

PT

12

H1

13

H2

14

TEST

C6011[KB]

C60210[KB]

PIN

14 CCDOUT13 GND

12 V111 V210 V39 V48 GND

7 GND

6 +12V5 RESET4 -6.5V3 H22 H11 SUB

NTSC :MN39168FDPAL :MN39268FD

[2012]

(BUFFER)

[3216]

31 2

A

B

TO MAIN P.C.B.FP31

REC VIDEO SIGNAL

(CCD)

SW8201ABC29065-A

SW8202ESE18L61D

30292827262524232221

181716151413121110987654321

1920

22212019181716151413121110987654321

GNDLCD_OPENLCD_HCK2LCD_HCK1LCD_PCG

LCD_+8.5VLCD_R/L

LCD_WIDELCD_HST

LCD_B

LCD_RLCD_G

LCD_PSIG/LCD_VCSHLCD_XSTB/LCD_FR

LCD_U/DLCD_EN

LCD_VCKLCD_VST

LCD_COM

LCD_BL_+5VLCD_BL_+5V

BL_CONTD_GNDD_GND

LCD_RVSSPOUT2SPOUT1

GNDNC

LIBATT++

LCD_HCK2LCD_HCK1

LCD_EN

D_GND

LCD_VST

LCD_PSIG/LCD_VCSHLCD_R

LCD_R/L

LCD_BL_+5V

LCD_U/D

LCD_PCG

LCD_G

LCD_HST

D_GND

LCD_XSTB/LCD_FR

LCD_VCK

LCD_B

LCD_COM

BL_CONT

LCD_BL_+5V

LCD_+8.5V

LCD_WIDE

TO MAIN P.C.B.FP81

TO LCD BACKLIGHTP.C.B. FP8101

LCDOPEN

NORMAL/REVERSE

PB VIDEO SIGNALREC VIDEO SIGNAL

A

B

1 2 3

PB AUDIO SIGNALREC AUDIO SIGNAL

SPEAKERSP001+

BT001BATTERY

R9

R8

SW13

PC

R7

SW3 START/STOPSW10

TAPE PLAYSW5 POWER

DEW SENSOR

D001 STANDBY

D002 POWER

SW11

CARD REC

SW12

CARD PLAY

SW14

DOWN(STOP)

R12

SW17

UP(PLAY)

R11

R10

R13

SW15

RIGHT(FF)

SW16

LEFT(REW)

R14

SW18

MENU

SW19

ENTER

R15

SW1 LIGHT

SW9

TAPE RECR6

SW2EJECT

SW7PHOTO_SW1

R1ZOOM

SW6FOCUS

SW4RESET

R4

R5

SW8PHOTO_SW2

R3R2

PIN

262524232221

181716151413121110987654321

1920

MODE DIAL CROSS KEY

[MF][MNL]

NCGND

EJECT

ZOOM_COM

NC

S/S_SWAD_KEY1(MODE-DIAL)

AD_KEY2(CROSS-KEY)

DEW

NC

NC

AUTO/MNL_SW

RESET_SW

AD_KEY5(LIGHT_SW)

PHOTO_SW

NC

STANDBY_LED

POWER_SW

AD_KEY3(OPE-KEY1)

VREF_L(WIDE)

GNDNC

GND(LED)

MODE_VDD

POWER_LED

VREF_H(TELE)

TO MAIN P.C.B.FP61

A

B

1 2 3

49

11.6. INTERCONNECTION SCHEMATIC DIAGRAM





INTERCONNECTION SCHEMATIC DIAGRAM

INTERCONNECTION SCHEMATIC DIAGRAM

FP31

FP8901FP8902 FP81

LCD BACKLIGHT P.C.B.

MAIN CHASSIS UNIT

MAIN P.C.B. LCD PANEL

CCD P.C.B

LENS UNIT

ECM UNIT

SIDE L OPERATION UNIT

EVF BACKLIGHT EVF FPC

CYLINDER UNIT

CAPSTAN UNIT

DC JACK

BATTERYTERMINAL

FP71

FP24

FP22

FP23

FP6501

FP61

(22 Pins)

(18 Pins) (16 Pins)

FP91

(18 Pins)

FP11

(12 Pins)

(14 Pins)

P1203

(8 Pins)

FP72

(12 Pins)

FRONT P.C.B.

BATTERY CASE UNIT

USBJACK

DVJACK

AV/HPJACK

(10 Pins)

(18 Pins)

MECHANISM FPC

(26 Pins)

(3 Pins)

FP8101 FP8102

(30 Pins) (22 Pins)

FP41

(22 Pins)

(24 Pins)

FJ4801FP21

(26 Pins)

710

EVF LCD PANEL

SIDE R SHAFT UNIT

LCD SWEVF UNIT

SPEAKER

SD UNIT

CARDSLOTSD CARD

85GC/EE, 88GK

50

12 Printed Circuit Board12.1. FRONT P.C.B.



NOTE:CIRCUIT BOARD LAYOUT SHOWS COMPONENTS INSTALLED FOR VARIOUS MODELS.FOR PROPER PARTS CONTENT FOR THE MODEL YOU ARE SERVICING,PLEASE REFER TO THE SCHEMATIC DIAGRAM AND PARTS LIST.

NOTE:CIRCUIT BOARD LAYOUT INCLUDES COMPONENTS WHICH ARE NOT USED.

Parts Location

(DUAL PATTERNS) (DUAL PATTERNS)

(COMPONENT SIDE) (FOIL SIDE)

FRONT P.C.B.LSEP8363B1/LSEP8363C1

FRONT P.C.B. LSEP8363B1 NV-GS80EG/EF/E/EP/EB/EK/EELSEP8363C1 NV-GS85EE/GC, NV-GS88GK

E

C

BE

C

B

EC

B

E

C

B

E

C

B

R4301R4302

R4305

R4303

R7804

R7802

R7803

R7801

R7102 C7815

C7814

C6505

C6501

FP6501

FJ4801

D4804 D4803

1

1

22

3

C6502

C6504

C6503

R6505

R6501

R6503R6502

R7815

1

45

123

4 5 6

8

IC7803

Q7801

R7810 R7814

C7813

R7812R7104R6504

R7105

D6503

R7809 R7813

R7807

R7805

R7811

R7806

R7808

C7802

C7804

C7808C7811 C7809

C7810C7812C7806

C7807

C7805

C7803

C7801

TP7805

TP7803

TP7802

TP7804

TP7806

TP7801

C4301

D4303 D4302

Q4302

Q4306

Q4307

Q4305

Q4301

LSJB8363

1

2

3

A B C

4

EC

B

E

C

B

1

2

3

A B C

4R4308

R4306

D4301

C7101

C7102

R7103

L7801

R4802

C4812

C4806

R4807

D4801

R4804

R4811

R4803

R4808

R4809

R4810

D4802

C4803

C4802C4808

C4809

C4810

C4801

1

1

11

5

4 3 22

23

4

34

4 5

8

C4805 C4804

R4805

R4806

U6501

R6507

R6506

R6509

Q6501

Q6502

Q4801

JK7101

D7101

D6504

R7101IC7802

IC7801

IC4801

R4307

B

C

E

LSJB8363

FRONT P.C.B.Integrated Circuits C7805 B-3 CIC4801 B-1 F C7806 B-3 CIC7801 B-3 F C7807 B-3 CIC7802 B-3 F C7808 B-3 CIC7803 B-3 C C7809 B-3 C

Transisters C7810 B-3 CQ4801 B-2 F C7811 B-3 CQ6501 A-2 F C7812 B-3 CQ6502 B-2 F C7813 C-3 CQ7801 B-3 C C7814 B-3 C

Test Points C7815 B-3 CTP7801 B-3 C ResistorsTP7802 B-3 C R4802 B-2 FTP7803 B-3 C R4803 B-1 FTP7804 B-3 C R4804 B-2 FTP7805 B-3 C R4805 B-2 FTP7806 B-3 C R4806 B-2 F

Connectors R4807 B-1 FFP6501 B-1 C R4808 B-1 F

Diodes R4809 B-1 FD4803 A-1 C R4810 B-1 FD4804 A-1 C R6501 B-2 CD6503 B-2 C R6502 B-2 CD6504 A-3 F R6503 B-2 CD7101 B-3 F R6504 B-2 C

Coil R6505 B-3 CL7801 B-2 F R6506 B-2 F

Capacitors R6507 B-2 FC4801 B-2 F R6509 A-2 FC4802 B-1 F R7101 B-3 FC4803 B-2 F R7102 B-3 CC4804 B-2 F R7103 B-2 FC4805 B-2 F R7104 B-2 CC4806 B-1 F R7801 B-3 CC4808 B-1 F R7802 B-3 CC4809 B-1 F R7803 B-3 CC4810 B-1 F R7804 B-3 CC4812 A-1 F R7805 B-3 CC6501 B-2 C R7806 B-3 CC6502 B-2 C R7807 B-3 CC6503 B-2 C R7808 C-3 CC6504 B-3 C R7809 B-3 CC6505 B-3 C R7810 B-3 CC7101 A-3 F R7811 B-3 CC7102 B-3 F R7814 C-3 CC7801 B-3 C R7815 B-3 CC7802 B-3 C MiscellaneousC7803 B-3 C JK7101 A-3 FC7804 B-3 C U6501 A-2 F

51

12.2. LCD BACKLIGHT P.C.B.


2 NOTE:ALL INDIVIDUAL PARTS EXCEPT D8102, D8104, D8107, D8109 AND D8111ON LCD BACKLIGHT P.C.B. ARE SUPPLIED AS REPLACEMENT PARTS.WHEN SERVICING THESE PARTS, REPLACE LCD BACKLIGHT P.C.B.INSTEAD OF INDIVIDUAL PARTS.

(FOIL SIDE)(COMPONENT SIDE)

LCD BACKLIGHT P.C.B. LSEP8367A1

(DUAL PATTERNS) LCD BACKLIGHT P.C.B.LSEP8367A1

(DUAL PATTERNS)

Parts Location


NOTE:CIRCUIT BOARD LAYOUT SHOWS COMPONENTS INSTALLED FOR VARIOUS MODELS.FOR PROPER PARTS CONTENT FOR THE MODEL YOU ARE SERVICING,PLEASE REFER TO THE SCHEMATIC DIAGRAM AND PARTS LIST.

NOTE:CIRCUIT BOARD LAYOUT INCLUDES COMPONENTS WHICH ARE NOT USED.

LCD BACKLIGHT P.C.B.Transisters Resistors

Q8101 C-4 C R8102 B-3 CQ8102 C-4 C R8103 B-3 CQ8104 C-4 C R8105 B-3 CQ8105 C-4 C R8106 B-3 CQ8107 B-1 C R8107 C-4 CQ8108 C-4 C R8108 C-4 CQ8112 B-4 C R8110 B-4 CQ8113 B-3 C R8112 C-4 C

Connectors R8113 C-4 CFP8101 B-2 C R8114 B-1 CFP8102 C-1 C R8115 B-1 C

Diodes R8116 B-1 CD8101 B-4 C R8119 C-4 CD8113 B-3 C R8123 B-1 C

Coil R8124 C-4 CL8101 A-3 C R8126 B-3 C

Capacitors R8127 B-4 CC8104 B-3 C R8135 B-4 CC8105 B-3 C R8136 C-4 CC8106 B-3 C R8143 B-2 CC8107 B-3 C R8145 B-4 CC8109 A-3 C R8153 B-1 CC8111 B-1 C R8154 C-1 CC8112 B-4 C R8155 B-1 CC8113 B-3 CC8116 B-4 C

B

C

EB

C

E

E

C

BE

CB

EC

B

E

C

B

1

2

3

A B C

4

Q8101

Q8103

Q8108

Q8105

Q8102

Q8104

R8107

R8129R8127R8130R8134

R8115R8116

Q8112 Q8109

R8135

R8136

R8111

R8124

R8113

R8119

D8101C8101

R8112

R8110

R8145C8112R8146

R8141

C8119

R8140

R8126

R8133

FP8103

R8103

Q8113

C8113

C8118C8117

C8120

R8139

R8138

R8143

R8142R8149

R8159

C8103C8102

R8160

R8144

R8154R8153R8148

R8150

R8151

R8123R8115

R8114R8116C8110C8111

R8122

R8152R8155

Q8114

Q8116 Q8107

Q8115

LSJB8367

1

24

22

24

1

1

FP8102

FP8101

C810

8

D8113

C8107C8105C8106C8104

L8101C8109 R8102 R8105 R8106

R8156R8157R8158

R8109

R8108

R8118

EC

B

EC

B

EC

B

EC

B

EC

B

EC

B

E

C

B

1

2

3

A B C

4

D811

1D8

110

D810

9D8

108

D810

7D8

106

D810

4D8

105

D810

2D8

103

D811

2

LSJB8367

52

13 Exploded Views13.1. MAIN PARTS SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

1Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.

MAIN PARTS SECTION

2

519

710

26

Lens Ass'y

Front Case Ass'y

537

537

12

519

519

537

Side R Shaft Unit & LCD Ass'yFP61 FP23

FP21

FP31

FP81FP72 FP22

FP24

FP6501

518 518519

537

519

519

7

537

519

519 519 519519

519

519

519

519

519

24

441

441

441

537


519

-3

-4

-3

-7

-8

-7

-5

-2

-2

-1-1

537 -2

-1

537 -2

-1

-1-1

-1

-5

-3-3

-2

-4

-4

-3

-6

-6

FP71

FP91FP11

(L-1)

(L-1)

AB

CD

E

E

AB

CD

E10

53

13.2. FRONT AND BOTTOM CASE SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

2 FRONT AND BOTTOM CASE SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.537

537

537

537

537533

702

701

705

703

53

56

6

7

72

30

48

47

519

519

537

519

28

29

45

3246

519

E30





704(NV-GS85EE-S/GC-S, NV-GS88GK-S)

54

13.3. SIDE R SHAFT UNIT AND LCD SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

3 SIDE R SHAFT UNIT AND LCD SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.

(L-2)

(L-4)

(L-3)

(L-3)(L-3)

(L-4)

(L-2)

(L-4)

(L-2)

519

519

533

E40

FP8101

FP8102

33

4236

39

37

38

31

40

44

41

35

34

A

A

B

B

LCD Panel Ass'y

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

(L-1)

55

13.4. CCD AND LENS SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

4 CCD AND LENS SECTION

LUBRICATION POINTSWhen the marked parts are replaced, apply the recommended lubricants or adhesive for better maintenance of the unit.

Mark Kind of LubricantGrease Available from Factroy LSUQ0050

Availability Part Number

Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly and Assembly Instructions" section.

Solder

66

65

533

533

538

538

538538

63

9

64

61

536

536

533

Solder

Lubrication Points

Lubrication Points

E50

56

13.5. EVF SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

5 EVF SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.2. The parts indicated by the dotted line are for Ass'y only and are not supplied.3. Disregard Ref. No. suffixes when ordering parts. They are used to describe parts in "Disassembly/Assembly Procedures" section.

(L-2)

(L-1)(L-1)

(L-2)

13

17

14

23

20

18

22

12

21

15

519

519

533

533

519

FP8901(not supplied)

57

13.6. MECHANISM SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

6 MECHANISM SECTION

201

NOTE 1 : When replacing the Main Chassis Unit (Ref. No. 201) or Cylinder Unit (Ref. No. 202), be sure to perform the Envelope Output Adjustment. Refer to "ENVELOPE OUTPUT ADJUSTMENT" in Mechanical Adjustment.

NOTE 1

534534

534

202

535

203

NOTE 1

58

13.7. PACKING PARTS AND ACCESSORIES SECTION

A

B

C

D

E

F

G

H

1 2 3 4 5 6

7 PACKING PARTS AND ACCESSORIES SECTIONIMPORTANT SAFTY NOTICE:

COMPONENTS IDENTIFIED BY THE SIGN HAVE SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS.

113NOTE 2not supplied(NV-GS85EE-S/GC-S,

NV-GS88GK-S)

101

not supplied

120

103

107

104

110

112

108

115

not supplied

125

128

129

(NV-GS88GK-S)

(NV-GS80EG-S/EF-S/E-S/EP-S/EK-S/EE-S, NV-GS85EE-S/GC-S)

(NV-GS80EB-S, NV-GS85GC-S)

(NV-GS85EE-S/GC-S, NV-GS88GK-S)

133

NOTE 2 : Battey is not supplied as a replacemet part. Purchase CR2025 battery locally if required.

59

BEFORE REPLACING PARTS, READ THE FOLLOWING:

1. Use only original replacement parts:

To maintain original function and reliability of repaired units,use only original replacement parts which are listed withtheir part numbers in the parts list.

2. IMPORTANT SAFETY NOTICE

Components identified by the sign have specialcharacteristics important for safety. When replacing any ofthese components, use only the specified parts.

3. Definition of Parts supplier:

a. Parts with mark "SPC" in the Remarks column aresupplied from Spare Parts Center of Panasonic AVCCompany.

b. Parts without mark in the Remarks column are suppliedfrom PSEC.

4. Parts whose Ref. Nos. are the same are interchangeable asreplacement parts. Any of these parts may be ordered andused as a replacement part.

5. Model Number Indication:

Model numbers are indicated in the Remarks columnwithout "NV-GS."

6. Unless otherwise specified;

All resistors are in Ω, K = 1,000 Ω, M = 1,000 kΩ.

7. Abbreviation

RTL: Retention Time Limited

This indicates that the retention time is limited for this item.After the discontinuation of this item in production, it will nolonger be available.

NR: Non Repairable Board Ass´y

MGF CHIP: Metal Glaze Film Chip

C CHIP: Ceramic Chip

COMPLX CMP: Complex Component

W FLMPRF: Wirewound Flameproof

P.C.B.: Circuit Board Assembly

P.C.B.: Printed Circuit Board

E.S.D.: Electrostatically Sensitive Devices

CSP: Chip Size Package

8. AC Adaptor

a. VSK0561 is indicated on the AC Adaptor used in thefollowing models:

NV-GS88GK

However, the AC Adaptor replacement part number isDE-974HC which should be used when ordering.

b. VSK0561 is indicated on AC Adaptor used in thefollowing models:

NV-GS80EG, NV-GS80EF, NV-GS80E, NV-GS80EP,NV-GS80EB, NV-GS80EK, NV-GS80EE, NV-GS85EE,NV-GS85GC, NV-GS88GK

However, the AC Adaptor replacement part number isDE-974GC which should be used when ordering.

14.1. MECHANICAL REPLACEMENTPARTS LIST

Definition of Parts supplier:

1. Parts with mark "SPC" in the Remarks column aresupplied from Spare Parts Center of Panasonic AVCCompany.

2. Parts without mark in the Remarks column are suppliedfrom PSEC.

MECHANICAL REPLACEMENT PARTSRef.No.

Part No. Part Name & Description Remarks

2 LSYK1900 SIDE L OPERATION UNIT 80EG/EF/E/EP/EB/EK/EE

2 LSYK1931 SIDE L OPERATION UNIT 85EE/GC,88GK

6 LSHN0020 TRIPOD

7 LSXK0288 BOTTOM UNIT 80EG/EF/E/EP/EB/EK/EE

7 LSXK0287 BOTTOM UNIT 85EE/GC,88GK

9 LSMA0968 LENS ANGLE

12 LSXK0286 EVF UNIT RTL

13 LSKM1233 EVF BASE FRAME

14 LSMA0970 EVF SPRING

15 LSMA0971 EVF EARTH PLATE

17 LSEP8372A1 EVF BACKLIGHT F.P.C.

18 LSGQ0221 EYE CAP

20 LSYK1904 EVF CASE 1 UNIT,ABS RESIN

21 LSKM1234 EVF CASE,ABS RESIN

22 LSGT0615 EYE SIGHT LEVER

23 LSYK1907 EVF LENS UNIT

24 LSYK1884 MAIN FRAME UNIT

26 LSYK1916 BATTERY CASE UNIT,ABS RESIN

28 LSGQ0222 TRIPOD SHEET

29 LSKF0671 SD COVER 85EE/GC,88GK

30 LSMB0331 SD COVER PIN 85EE/GC,88GK

31 LSYK1988 SIDE R SHAFT UNIT

32 LSMB0332 BELT PIN

33 LSKM1251 LCD CASE A,ABS RESIN 80EG/EF/E/EP/EB/EK/EE

33 LSKM1524 LCD CASE A,ABS RESIN 85EE/GC

33 LSKM1228 LCD CASE A,ABS RESIN 88GK

34 LSKM1232 LCD CASE B,ABS RESIN

35 LSSC0924 LCD SHIELD CASE,ABS RESIN

36 LSYK1924 PANEL HOLDER UNIT

37 LSGL0505 LEAD LIGHT PANEL

38 LSGL0511 DIFFUSION SHEET

39 LSGL0506 REFLECT SHEET

40 LSGL0443 BEF SHEET

41 LSGL0444 BEF SHEET A

42 L5BDDYH00025 LIQUID CRYSTAL DISPLAY PANEL

44 LSYK1923 LCD CASE B UNIT,ABS RESIN RTL

45 LSSC0927 SD EARTH PLATE 85EE/GC,88GK

46 LSGL0510 ACCESS LED PANEL 85EE/GC,88GK

47 LSKF0668 LENS CAP COVER

48 LSKF0669 LENS CAP HINGE

53 LSKF0670 JACK COVER

56 LSYK1912 FRONT CASE UNIT,ABS RESIN

61 LSXN0046 LENS UNIT

63 LSFL0292 OPTICAL LOW PASS FILTER

64 LSMX0230 FILTER RUBBER

65 L6HA66NB0007 ZOOM MOTOR UNIT

14 Replacement Parts Lists

60

Ref.No.


66 L6HA66NB0008 FOCUS MOTOR UNIT

72 LSGQ0223 GRIP BELT

101 VPF1129 POLY BAG

103 LSPG2339 PACKING CASE,PAPER 80EG/EF/E/EP/EB/EK

103 LSPG2438 PACKING CASE,PAPER 80EE

103 LSPG2337 PACKING CASE,PAPER 85EE/GC

103 LSPG2338 PACKING CASE,PAPER 88GK

104 LSPN0767 PAD

107 LSPN0772 TOP PAD

108 K2GJ2DC00015 DV CABLE W/PLUG

110 DE-974GC AC ADAPTOR80EG/EF/E/EP/EB/EK/EE,85EE/GC

110 DE-974HC AC ADAPTOR 88GK

112 K2KC4CB00022 AUDIO VIDEO CABLE W/PLUG

113 N2QAEC000021 INFRARED REMOTE CONTROL UNIT 85EE/GC,88GK

115 K1HA05CD0015 USB CABLE W/PLUG 85EE/GC,88GK

120 LSQT1127-A INSTRUCTION BOOK(GERMAN/FRENCH/ITALIAN/DUTCH/TURKISH)

80EG/EK

120 LSQT1128-A INSTRUCTION BOOK (FRENCH) 80EF

120 LSQT1129-A INSTRUCTION BOOK(PORTUGUESE/SPANISH/SWEDISH/DANISH)

80E

120 LSQT1130-A INSTRUCTION BOOK(ENGLISH/POLISH/CZECH/HANGARIAN)

80EP

120 LSQT1131-A INSTRUCTION BOOK (ENGLISH) 80EB

120 LSQT1234-A INSTRUCTION BOOK(RUSSIAN/UKRAINIAN)

80EE

120 LSQT1124-A INSTRUCTION BOOK(RUSSIAN/UKRAINIAN)

85EE

120 LSQT1123-A INSTRUCTION BOOK(CHINESE(TRADITIONAL)/ENGLISH/RUSSIAN/ARABIC)

85GC

120 LSQT1126-A INSTRUCTION BOOK(CHINESE(SIMPLIFIED))

88GK

125 K2CR2DA00004 AC CORD W/PLUG80EG/EF/E/EP/EK/EE,85EE/GC

128 K2CA2CA00020 AC CORD W/PLUG 88GK

129 K2CT3CA00004 AC POWER CORD W/PLUG,250V80EB,85GC

133 LSPF0107 POLY BAG

201 VXY1979Z1 MAIN CHASSIS UNIT

202 VEG1663-M CYLINDER UNIT

or 202 VEG1704-M CYLINDER UNIT

or 202 LSEG0179 CYLINDER UNIT

203 VXA8334 CASSETTE UP UNIT SPC

441 VHD1133 SCREW,STEEL

518 XQS2+A35FN SCREW,STEEL

519 XQN16+BF4FN SCREW,STEEL

533 XQN16+BJ4FN SCREW,STEEL

534 VHD1861 SCREW,STEEL

535 XQN14+B2FN SCREW,STEEL

536 XQN16+AJ4FN SCREW,STEEL



701 LSEK0684 ELECTRIC CONDENSOR MICROPHONEUNIT

702 LSMG0136 MIC DAMPER

703 LSSC0926 FRONT EARTH PLATE

704 B3RAB0000064 INFRARED RECEIVER 85EE/GC,88GK

705 LSKM1243 JACK PIECE

710 LSJB8369 FRONT F.P.C.

Ref.No.


E10 LSEP8361P1 MAIN P.C.B. RTL80EG/EF/E/EP/EB

E10 LSEP8361R1 MAIN P.C.B. RTL80EK/EE

E10 LSEP8361Q1 MAIN P.C.B. RTL85EE/GC,88GK

E30 LSEP8363B1 FRONT P.C.B. RTL80EG/EF/E/EP/EB/EK/EE

E30 LSEP8363C1 FRONT P.C.B. RTL85EE/GC,88GK

E40 LSEP8367A1 LIQUID CRYSTAL DISPLAYBACKLIGHT P.C.B.NR

E50 LSEQ0831 CCD P.C.B.NR

SERVICE FIXTURES AND TOOLSRef.No.


VFM3110EDS COLOR BAR STANDARD TAPE SPC

VFK1451 DVC HEAD CLEANING TAPE SPC

LSVQ0028 PLIER FOR NON ZIF CONNECTOR

LSUQ0050 GREASE

LSUA0019 EXTENSION CABLE 8P


VUVS0007 EXTENSION CABLE 12P

VFKW0124A EXTENSION CABLE 14P


VFK1174 EXTENSION CABLE 30P


VUVS0012 EXTENSION CABLE 22P

VFK1164LBX1 LIGHT BOX SPC

VFK1164TCM02 INFINITY LENS (WITH FOCUSCHART)

SPC

VFK1164TAR58 ATTACHMENT RING (58mm) SPC







VFK1164TAR3A ATTACHMENT RING (30.5mm) SPC


VFK1164TFCT2 COLOR CONVERSION FILTER (C14) SPC

VFK1164TFWC2 WHITE CHART SPC

VFK1164TFCB2 COLOR BAR CHART SPC

VFK1164TFGS2 GRAY SCALE CHART SPC

VFK1899 POST HEIGHT ADJUSTMENTFIXTURE

SPC

14.2. ELECTRICAL REPLACEMENTPARTS LIST

Definition of Parts supplier:

1. All parts are supplied from PSEC.

PRINTED CIRCUIT BOARD ASSEMBLYRef.No.


E10 LSEP8361P1 MAIN P.C.B. E.S.D.RTL80EG/EF/E/EP/EB

E10 LSEP8361R1 MAIN P.C.B. E.S.D.RTL80EK/EE

E10 LSEP8361Q1 MAIN P.C.B. E.S.D.RTL85EE/GC,88GK

61

Ref.No.


E30 LSEP8363B1 FRONT P.C.B. RTL80EG/EF/E/EP/EB/EK/EE

E30 LSEP8363C1 FRONT P.C.B. RTL85EE/GC,88GK

E40 LSEP8367A1 LIQUID CRYSTAL DISPLAYBACKLIGHT P.C.B.NR

E50 LSEQ0831 CCD P.C.B.NR

14.2.1. MAIN P.C.B.FPC CONNECTORS

Ref.No.


FP11 K1MN12BA0197 CONNECTOR 12P





FP31 K1MN14A00088 CONNECTOR 14P





FP81 K1MN30AA0091 CONNECTOR 30P


14.2.2. FRONT P.C.B.INTEGRATED CIRCUITS

Ref.No.


IC4801 C0ABBB000369 IC, LINEAR

orIC4801

C0ABBB000262 IC, LINEAR

IC7801 L2ES00000016 GYROSCOPE

IC7802 L2ES00000017 GYROSCOPE

IC7803 C0ABHA000078 IC, LINEAR

TRANSISTORSRef.No.


Q4801 2SD2216J08 TRANSISTOR SI NPN CHIP

orQ4801

B1ABCF000104 TRANSISTOR SI NPN CHIP

orQ4801


Q6501 B1ABCF000098 TRANSISTOR SI NPN CHIP

orQ6501


Q6502 2SB1218AHL TRANSISTOR SI PNP CHIP

orQ6502

B1ADCF000063 TRANSISTOR SI PNP CHIP

orQ6502

B1ADCF000075 TRANSISTOR SI PNP CHIP

Q7801 XP0450100L TRANSISTOR COMPLX CMP SI NPNCHIP

orQ7801

B1HBCFA00011 TRANSISTOR COMPLX CMP SI NPNCHIP

orQ7801

B1HBCFA00016 TRANSISTOR COMPLX CMP SI NPNCHIP

DIODESRef.No.


D4803 B0ACCJ000027 DIODE SI CHIP

orD4803

MA2S111008 DIODE SI CHIP

D4804 B0ACCJ000027 DIODE SI CHIP

orD4804

MA2S111008 DIODE SI CHIP

D6503 B0ADEJ000038 DIODE SI CHIP

D6504 B3GA00000062 INFRARED SENSOR

D7101 D4ED1120A005 SURGE ABSORBER

RESISTORSRef.No.


R4802 ERJ3GEYJ472V MGF CHIP 1/16W 4.7K

R4803 ERJ3GEYJ223V MGF CHIP 1/16W 22K




R4807 D0HB392ZA002 MGF CHIP 1/16W 3.9K



R4810 D0HB392ZA002 MGF CHIP 1/16W 3.9K

R6501 ERJ3GEYJ560V MGF CHIP 1/16W 56 85EE/GC,88GK

R6502 ERJ3GEYJ683V MGF CHIP 1/16W 68K 85EE/GC,88GK


R6504 ERJ3GEYJ106V MGF CHIP 1/16W 10M

R6505 ERJ3GEYJ335V MGF CHIP 1/16W 3.3M




R7101 J0JBC0000027 FERRITE BEAD CHIP

















CAPACITORSRef.No.


C4801 F1H1A105A036 C CHIP 10V 1UF

C4802 F1H1A105A036 C CHIP 10V 1UF

C4803 F1J0J106A004 C CHIP 6.3V 10UF

C4804 F1H1H822A219 C CHIP 50V 8200PF

C4805 F1H1C273A041 C CHIP 16V 0.027UF

C4806 F1H1C273A041 C CHIP 16V 0.027UF

C4808 F1H1C273A041 C CHIP 16V 0.027UF

C4809 F1H1H822A219 C CHIP 50V 8200PF

C4810 F1H1C273A041 C CHIP 16V 0.027UF

C4812 F3F0J226A032 TANTALUM CHIP 6.3V 22UF

C6501 F3F0J106A032 TANTALUM CHIP 6.3V 10UF 85EE/GC,88GK

C6502 F1H1C104A008 C CHIP 16V 0.1UF 85EE/GC,88GK

C6503 F1H1A224A012 C CHIP 10V 0.22UF

C6504 F1H1C104A041 C CHIP 16V 0.1UF

C6505 F1H1A224A012 C CHIP 10V 0.22UF

C7101 F1H1H472A219 C CHIP 50V 4700PF

C7102 F1H1H472A219 C CHIP 50V 4700PF

C7801 F1J1A106A023 C CHIP 10V 10UF

C7802 F1J1A106A023 C CHIP 10V 10UF



C7805 F1H1H153A219 C CHIP 50V 0.015UF

C7806 F1H1H153A219 C CHIP 50V 0.015UF

C7807 F1H1H153A219 C CHIP 50V 0.015UF

C7808 F1H1H153A219 C CHIP 50V 0.015UF

C7809 F1J1A106A023 C CHIP 10V 10UF

C7810 F1J1A106A023 C CHIP 10V 10UF

C7811 F1J1A106A023 C CHIP 10V 10UF

C7812 F1J1A106A023 C CHIP 10V 10UF

C7813 F1H1H222A219 C CHIP 50V 2200PF

C7814 F1H1H222A219 C CHIP 50V 2200PF

C7815 F1H0J1050012 C CHIP 6.3V 1UF

62

COILSRef.No.


L7801 G1C100KA0055 COIL CHIP 10UH

FPC CONNECTORRef.No.



JACKRef.No.


JK7101 K2HC105E0007 MIC JACK SOCKET

MISCELLANEOUSRef.No.



701 LSEK0684 ELECTRIC CONDENSOR MICROPHONEUNIT

702 LSMG0136 MIC DAMPER

703 LSSC0926 FRONT EARTH PLATE

704 B3RAB0000064 INFRARED RECEIVER 85EE/GC,88GK

705 LSKM1243 JACK PIECE

14.2.3. LIQUID CRYSTAL DISPLAYBACKLIGHT P.C.B.NR

TRANSISTORSRef.No.


Q8101 2SC6054J0L TRANSISTOR SI NPN CHIP




Q8107 2SA2174J0L TRANSISTOR SI PNP CHIP




DIODESRef.No.


D8101 MAZ80620ML DIODE ZENER CHIP 6.2V

D8113 MAZ80560ML DIODE ZENER CHIP 5.6V

RESISTORSRef.No.


R8102 ERJ3RBD271V MGF CHIP 1/16W 270

R8103 ERJ6GEY0R00V MGF CHIP 1/10W 0



R8107 ERJ3RED270V MGF CHIP 1/16W 27





R8114 ERJ3RBD563V MGF CHIP 1/16W 56K















CAPACITORSRef.No.


C8104 ECJ1VC1H390J C CHIP 50V 39PF



C8107 F1H1A105A036 C CHIP 10V 1UF

C8109 F1J1A475A023 C CHIP 10V 4.7UF

C8111 F1H1C104A041 C CHIP 16V 0.1UF

C8112 F1J1A2250007 C CHIP 10V 2.2UF

C8113 F1H1A105A036 C CHIP 10V 1UF

C8116 F1H0J1050012 C CHIP 6.3V 1UF

COILSRef.No.


L8101 G1C101KA0055 COIL CHIP 100UH

FPC CONNECTORRef.No.




63

15 Voltage Chart

MODE REC PIN NO.

MODE REC PIN NO.

MODE REC PIN NO.

MODE REC PIN NO.

MODE REC PIN NO.

MODE REC PIN NO.

MODE REC PIN NO.

FP111 02 03 04 05 06 07 ---8 8.19 8.110 8.111 8.112 8.1

FP211 ---2 03 2.84 05 1.46 1.57 2.48 1.49 1.410 0.411 8.112 7.413 014 015 2.816 2.817 2.818 019 020 021 022 023 024 025 026 0

FP221 02 03 1.64 1.65 1.66 1.67 1.68 1.69 1.610 0

FP231 1.32 0

3 1.34 2.65 0.66 0.67 2.38 2.89 2.410 1.411 0.512 1.413 014 0.515 0.616 0.617 0.518 0.5

FP241 02 03 04 1.95 1.96 1.97 1.98 0

FP311 8.22 03 -0.24 -0.25 -6.16 -6.17 08 09 11.910 5.811 6.512 1.513 1.814 6.6

FP411 02 03 1.44 1.45 2.86 1.27 1.38 09 010 011 012 4.813 4.8

14 4.815 0.116 1.817 0.218 0.219 020 021 2.622 0

FP611 2.82 ---3 04 ---5 06 ---7 2.88 2.89 2.810 2.011 1.812 1.813 ---14 015 ---16 017 018 1.719 2.820 2.221 2.822 023 1.424 1.525 ---26 0

FP711 1.42 1.43 1.44 1.45 4.56 4.87 08 4.89 010 4.411 1.212 013 1.414 1.415 1.416 1.217 2.7

18 0.119 2.020 1.521 0.822 1.4

FP721 1.62 1.33 1.44 1.45 1.06 1.47 1.88 1.49 1.810 1.411 1.012 1.4

FP811 02 03 1.34 1.35 0.26 8.67 2.88 09 010 2.511 2.512 2.513 2.514 2.815 2.816 2.217 1.218 0.119 2.220 4.821 4.822 2.323 024 025 1.826 0.327 0.228 029 ---30 3.2

FP911 2.82 03 04 0

5 06 2.57 -0.78 2.59 8.610 2.511 0.212 2.513 2.114 015 1.216 1.417 1.418 2.2

MAIN P.C.B.

64

Documents

PANASONIC NV GS80 85 Manual Reparatii