Panasonic KX-NCP1000 R14 - MegaPath · Panasonic KX-NCP1000 R14 SIP Trunk Setup Guide ABSTRACT The Panasonic KX-NCP1000 is a Network Communication Platform (NCP) that provides unified

Panasonic

KX-NCP1000

R14 SIP Trunk Setup Guide

Panasonic KX-NCP1000 R14.

Last Update: 10/05/2012

Panasonic KX-NCP1000 R14 SIP Trunk Setup Guide

ABSTRACT

The Panasonic KX-NCP1000 is a Network Communication Platform (NCP) that provides

unified communication solutions for small to medium businesses. The KX-NCP1000

combines digital (IP) and analog telephony. It is a hybrid system, a mix of key system and

PBX, to include computer telephony integration (by way of software components).

Contents INTRODUCTION ............................................................................................................................................ 1

1. STANDARD FIREWALL ................................................................................................................................. 1

1.1 ADD SIP TRUNK .............................................................................................................................. 2

2. EDGEMARC APPLICATION-LAYER GATEWAY ................................................................................................... 7

2.1 ADD SIP TRUNK .............................................................................................................................. 8

2.3 EDGEMARC SIP ALG SIP TRUNK CONFIGURATION ............................................................................... 13

1

INTRODUCTION

This document does not cover the installation of the KX-NCP1000 itself and assumes

knowledge of the system build and administration, to include access to the default KX-NCP

Maintenance console by way of client software provided by Panasonic.

This document covers MegaPath R14 SIP trunk configurations in conjunction with a third-

party firewall.

The R14 Identity/Device profile required for successful KX-NCP1000 interoperability is the

“Generic SIP Trunk Single Registration” Identity/Device profile.

IMPORTANT: Testing with the Edgemarc 4500-series SIP ALG HAS NOT been conducted at

this time. A known-good standard Edgemarc 4500-series SIP ALG configuration is provided

that works with the Generic SIP Trunk Single Registration Broadsoft R14 Identity/Device

profile.

1. STANDARD FIREWALL

This configuration features a KX-NCP1000 deployed behind a standard, third-party firewall.

The firewall is configured the forward SIP and the Asterisk RTP range from the firewall WAN

IP address to the internal IP address of the KX-NCP1000 NATd behind the firewall.

Figure 1.1 KX-NCP1000 NATd behind a standard, third-party firewall.

IMPORTANT NOTES:

The third-party firewall SHOULD support static NAT for all outbound and inbound

UDP traffic to mitigate one-way audio.

If one-way audio is still an issue with a firewall known to support static NAT, then

ensure that all SIP helper or SIP proxy services are disabled in the firewall.

Port forwarding of SIP and RTP ranges should be in place between the firewall and

the KX-NCP1000. The UDP port for SIP is 5060 and the RTP UDP port range starts at

16000.

Ensure you are clear as to which slot and port number to use when configuring the KX-

NCP1000 Virtual SIP Gateway.


2

1.1 Add SIP Trunk

1. Log in to the KX-NCP Maintenance Console

2. Go to Configuration.

3. Navigate to the Main tab under the Shelf Property – Virtual SIP Gateway tab.

Figure 1.1.1 Main tab under Shelf Property – Virtual SIP Gateway tab.


3

4. Select the applicable slot and port number.

5. Set the following parameters as listed below:

Figure 1.1.2 SIP client settings.

6. Access the Port Property – Virtual SIP Gateway>Main tab.

Figure 1.1.3 Port Property – Virtual SIP Gateway > Main tab.


4

7. Select the appropriate slot and port number.


Figure 1.1.4 SIP server settings.

9. Access the Port Property – Virtual SIP Gateway>Calling Party tab.

Figure 1.1.5 Calling Party tab under Port Property – Virtual SIP Gateway tab.


5

10. Select the applicable slot and port number. Set the following parameters as listed

below:

Figure 1.1.6 Calling Party settings.

11. Select the Port Property – Virtual SIP Gateway>Account tab.

Figure 1.1.7 Account tab under Port Property – Virtual SIP Gateway tab.


6



Figure 1.1.8 Account settings.


7

2. EDGEMARC APPLICATION-LAYER GATEWAY

This configuration features a KX-NCP1000 deployed behind an Edgemarc SIP application-

layer gateway (SIP ALG). The SIP ALG is configured to forward SIP and the RTP range from

the SIP ALG WAN IP address to the internal IP address of the KX-NCP1000 NATd behind the

SIP ALG.

Figure 2.1 KX-NCP1000 NATd behind an Edgemarc SIP ALG.

IMPORTANT: Testing with the Edgemarc 4500-series SIP ALG HAS NOT been conducted at

this time. A known-good standard Edgemarc 4500-series SIP ALG configuration is provided

that works with the Generic SIP Trunk Single Registration Broadsoft R14 Identity/Device

profile.

NOTE: In this example, the LAN-side IP address of the Edgemarc SIP application-layer

gateway is 172.16.248.1 and the IP address of the Panasonic KX-NCP1000 is

172.16.248.165.


8

2.1 Add SIP Trunk

1. Log in to the KX-NCP Maintenance Console.

2. Navigate to Configuration.

3. Access the Shelf Property – Virtual SIP Gateway >Main tab.

Figure 2.1.1 Main tab under Shelf Property – Virtual SIP Gateway tab.


9

4. Select the appropriate slot and port number. Set the following parameters as listed

below:

Figure 2.1.2 SIP client settings.

5. Access the Port Property – Virtual SIP Gateway>Main tab.

Figure 2.1.3 Main tab under Port Property – Virtual SIP Gateway tab.


10


7. Set the following parameters as listed below; the IP address used here is the LAN-

side IP address of the Edgemarc 4500-series SIP ALG:

Figure 2.1.4 Edgemarc SIP ALG settings.

1. Access the Port Property – Virtual SIP Gateway>Calling Party tab.

Figure 2.1.5 Calling Party tab under Port Property – Virtual SIP Gateway tab.


11



Figure 2.1.6 Calling Party settings.

4. Select the Port Property – Virtual SIP Gateway>Account tab.

Figure 2.1.7 Account tab under Port Property – Virtual SIP Gateway tab.


12



Figure 2.1.8 Account settings.


13

2.3 Edgemarc SIP ALG SIP Trunk Configuration

1. Log in to the Edgemarc SIP ALG.

2. Under the VoIP ALG menu option, select the SIP option.

3. In the SIP Settings>SIP Server Address field, enter the fully-qualified domain

name or IP address of the SIP gateway or session border controller assigned to you

by your VoIP service provider.

4. In the SIP Server Port field, enter the SIP server port number.

5. Enable Use Custom Domain.

6. In the SIP Server Domain field, enter speakeasy.net.

Figure 2.3.1 VoIP ALG, SIP Settings.

7. Submit changes.

8. From the SIP sub-menu, select Trunking.


14

9. In the Add a trunking device menu box:

A. Set the Action field to Add new trunking device.

B. In the Name field, enter a recognizable name for the trunking device.

C. In the Address field, enter the IP address of the KX-NCP1000server.

D. In the Port field, enter the SIP port number of the KX-NCP1000server.

E. Click the Commit button to create the SIP trunking device.

Figure 2.3.2 SIP Trunking, SIP Trunking devices


15

10. Under SIP Trunking, go to the “Rules” section to add an inbound rule.

NOTE: For a single SIP registration, we will be using a Default Rule to send all

inbound call traffic to the LAN-SIDE KX-NCP1000server.

11. In the “Add a rule” menu box:

A. Set the Action field to Add a new rule.

B. Set the Type field to Inbound.

C. Set the Trunking device field to the recognizable name you created for the

target trunking device in the last section.

D. Click Commit to create the Default Rule.

Figure 2.3.3 SIP Trunking, Rules, Add a rule.

Documents

Panasonic KX-NCP1000 R14 - MegaPath · Panasonic KX-NCP1000 R14 SIP Trunk Setup Guide ABSTRACT The Panasonic KX-NCP1000 is a Network Communication Platform (NCP) that provides unified