Upload
totalofficesupport
View
240
Download
0
Embed Size (px)
Citation preview
7/27/2019 Panasonic Dp2310 Service Manual
1/485
Order Number: MGCS040801C0H21
Digital Imaging SystemsDP-2310/3010DP-2330/3030
[ Version 2.1 ]
This service information is designed for experienced repair technicians only and is not intended for use by the general public.It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
WARNING
2005 Panasonic Communications Co., Ltd. All rights reserved. Unauthorized copying and distribution isa violation of law.
7/27/2019 Panasonic Dp2310 Service Manual
2/485
2
The contents of this Service Manual and the Specifications are subject to changewithout notice.Panasonic Communications Co., Ltd. reserves the right to make improvements inthe product design without reservation and without notice.Published in Japan.
Information regarding Lead-Free (PbF) solder:
Distinction of PbF PCB:PCBs (manufactured) using lead free solder will have a mark followingthe PCB part numbers in a label on the PCB.
Caution:Pb free solder has a higher melting point than standard solder; typicallythe melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering ironwith temperature control and adjust it to 700 20 F (370 10 C). Exercise care
while using higher temperature soldering irons, do not heat the PCB for too longto prevent solder splash or damage to the PCB.Pb free solder will tend to splash when heated too high (about 1100 F/600 C).ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:URL: http://www.senju-m.co.jp ) is recommended when repairing PbF PCBs.
This Product Uses Lead (Pb) Free Solder Printed CircuitBoards (PCBs).
http://www.senju-m.co.jp/http://www.senju-m.co.jp/7/27/2019 Panasonic Dp2310 Service Manual
3/485
3
Important NoticePlease read this notice completely BEFORE installing any optional accessories. As failure to properly install the additional board or connector with the power ON (only the front power switch Off) could damage the copier's SPC or SC board.
Please follow the instructions below:1.It is essential that you turn OFF power to the Main Power
Switch located in the rear of the copier.2.It is essential that you unplug the Main AC Power Cord from
the wall outlet.3. Please carefully read the installation instructions and follow
each step.
Note:If the Hard Disk Drive Unit is installed, to prevent a Disk Scan Function from beingperformed (similar to Windows OS when the power is abruptly interrupted), it isimportant to follow the step sequence below when turning OFF the Power Switches on
the machine.1. Turn the Power Switch on the Left Side of the machine to the OFF position first.2. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk
Drive Unit.3. Turn the Main Power Switch on the Back of the machine to the OFF position.
(This interrupts all the power to the machine)4. Unplug the AC Power Cord.
* The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation and without notice.
7/27/2019 Panasonic Dp2310 Service Manual
4/485
4
Hinweis:
7/27/2019 Panasonic Dp2310 Service Manual
5/485
5
Precautions
Power and Ground Connection CautionsEnsure that the plug connection is free of dust. In a damp environment, a contaminatedconnector can draw a significant amount of current that can generate heat and eventuallycause fire if left unattended over an extended period of time.
Always use the power cord provided with your machine. When an extension power cord is
required, always use a properly rated cord.120 V/15 A or AC 220 - 240V/10 AIf you use a cord with an unspecified current rating, the machine or plug may emit smoke orbecome hot to the touch.
Do not attempt to repair, pull, bend, chafe or otherwise damage the power cord. Do notplace a heavy object on the cord. A damaged cord can cause fire or electric shocks.
Never touch a power cord with wet hands. Danger of electric shock exists.
If the power cord is damaged or insulated wires are exposed, contact the authorizedPanasonic dealer for a replacement. Using a damaged cord can cause fire or electric
Stop operation immediately if your machine emits smoke, excessive heat, unusual noise, or
abnormal smell, or if water is spilt onto the machine. These conditions can cause fire.Immediately switch Off and unplug the machine, and contact the authorized Panasonic .
Do not disconnect or reconnect the machine while the power switch is in the On position.Disconnecting a live connector can cause arcing, consequently deforming the plug andcause fire.
When disconnecting the machine, grasp the plug instead of the cord. Pulling on a cordforcibly can damage it and cause fire or electric shock.
When the machine is not used over an extended period of time, switch it Off and unplug it.If an unused machine is left connected to a power source for a long period, degraded insulationcan cause electric shocks, current leakage or fire.
Be sure to switch Off and unplug the machine before accessing the interior of the machinefor cleaning, maintenance or fault clearance. Access to a live machine's interior can causeelectric shock.
For Your SafetyTo prevent severe injury and loss of life, read this section carefully before servicing the Panasonicmachine to ensure proper and safe operation of your machine.
This section explains the Warnings and Cautions used in the machine and/or this manual.
WARNING: Denotes a potential hazard that could result in serious injury or death.
CAUTION: Denotes hazards that could result in minor injury or damage to the machine.
This section also explains the Warnings and Cautions used in the machine and/or this manual.
These symbols are used to alert operators to a specific operating procedurethat must not be performed.
These symbols are used to alert operators to a specific operating procedurethat must be emphasized in order to operate the machine safely.
WARNING
Please ensure that the machine is installed near a wall outlet and is easily accessible.
shocks.
dealer.
7/27/2019 Panasonic Dp2310 Service Manual
6/485
6
Once a month, unplug the machine and check the power cord for the following. If you notice any unusualcondition, contact the authorized Panasonic dealer.
The power cord is plugged firmly into the receptacle.The plug is not excessively heated, rusted, or bent.The plug and receptacle are free of dust.The cord is not cracked or frayed.
Operating SafeguardsDo not touch areas where these caution labels are attached to, the surface may be very hot and may causesevere burns.
Do not place any liquid container such as a vase or coffee cup on the machine. Spilt water can cause fire orshock hazard.
Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get into themachine, they can short-circuit internal components, and cause fire or electric shocks.
If debris (metal or liquid) gets into the machine, switch Off and unplug the machine immediately.Operating a debris-contaminated machine can cause fire or electric shock.
Do not try to alter the machine configuration or modify any parts. An unauthorized modification can causesmoke or fire.
Consumable SafeguardsNever dispose of toner, toner cartridge or a waste toner container into an open flame. Toner remaining in thecartridge can cause an explosion, burns and/or injuries.
Keep button batteries/stamp out of the reach of children. If a button battery/stamp is swallowed accidentally,get medical treatment immediately.
Installation and Relocation CautionsDo not place the machine near heaters or volatile, flammable, or combustible materials such as curtains thatmay catch fire.
Do not place the machine in a hot, humid, dusty or poorly ventilated environment. Prolonged exposure tothese adverse conditions can cause fire or electric shocks.
Place the machine on a level and sturdy surface that can with stand.If tilted, the machine may tip-over and cause injuries.
When moving the machine, be sure to unplug the power cord from the outlet. If the machine is moved with thepower cord attached, it can cause damage to the cord which could result in fire or electric shock.
CAUTION
When relocating the machine, remove the toner and/or developer, and pack the machine with properpacking materials for shipping.
7/27/2019 Panasonic Dp2310 Service Manual
7/485
7
Operating SafeguardsDo not place a magnet near the safety switch of the machine. A magnet can activate themachine accidentally, resulting in injuries.
Do not use a highly flammable spray or solvent near the machine. It can cause fire.
When copying a thick document, do not use excessive force to press it against the scanningglass. The glass may break and cause injuries.
Never touch a labelled area found on or near the heat roller. You can get burnt. If a sheet ofpaper is wrapped around the heat roller, do not try to remove it yourself to avoid injuries orburns. Switch Off the machine immediately, and wait until it cools down.
Do not use conductive paper, e.g. folding paper, carbon paper and coated paper. When apaper jam occurs, they can cause a short circuit and fire.
Do not place any heavy object on the machine. An off-balance machine can tip-over or theheavy object can fall, causing damage and/or injuries.
Keep the room ventilated when using the machine for an extended period of time to minimizethe ozone density in the air.
When copying with the document cover open, do not look directly at the exposure lamp.Direct eye exposure can cause eye fatigue or eye injury.
Pull out paper trays slowly to prevent injuries.
When removing jammed paper, make sure that no pieces of torn paper are left in the machine.A piece of paper remaining in the machine can cause fire. If a sheet of paper is wrappedaround the heat roller, or when clearing a jammed paper that is difficult or impossible to see,do not try to remove it by yourself. Doing so can cause injuries or burns. Switch Off themachine immediately, and wait until it cools down.
Consumable SafeguardsNever heat the drum cartridge, or scratch its surface. A heated or scratched drum can behazardous to your health.
Do not mix new and old batteries together, as they can burst or leak, causing a fire or
injuries. Be sure to use the specified type of batteries only..
Ensure that batteries are installed with correct polarity. Incorrectly installed batteries canburst or leak, resulting in spillage or injuries.
OthersWhen clearing a paper jam or other fault, follow the appropriate procedure given in this manual.The machine has a built-in circuit for protection against lightning-induced surge current. If lightningstrikes in your neighborhood, switch Off the machine. Disconnect the power cord from the machineand reconnect only when the lightning has stopped.If you notice flickering or distorted images or noises on your audio-visual units, your machine maybe causing radio interference. Switch it Off and if the interference disappears, the machine is thecause of the radio interference. Perform the following procedure until the interference is corrected.
Move the machine and the TV and/or radio away from each other.Reposition or reorient the machine and the TV and/or radio.Unplug the machine, TV and/or radio, and replug them into outlets operating on different circuits.Reorient the TV and/or radio antennas and cables until the interference stops. For an outdoorantenna, ask your local electrician for support.Use a coaxial cable antenna.
CAUTION
7/27/2019 Panasonic Dp2310 Service Manual
8/485
8
memo
7/27/2019 Panasonic Dp2310 Service Manual
9/485
Table of Contents
9
Specifications Table ............................111.1. Copy Function.........................................11
1.2. Fax, Printer and Internet FaxFunctions .............................................. ..20
1.3. System Combination...............................29
1.4. Options List.............................................301.5. External View..........................................32
1.6. Control Panel..........................................35
1.7. Fans and Motors.....................................36
1.8. Clutches and Switches ...........................36
1.9. PC Boards ..............................................37
Disassembly Instructions .....................382.1. General Disassembly..............................38
2.2. Disassembly Instructions ........................39
2.3. Screw Identification Template.................82
Maintenance, Adjustments andCheck Points .......................................... 86
3.1. Preventive Maintenance .........................86
3.2. Required Tools .......................................88
3.3. Preventive Maintenance Points ..............89
3.4. Preventive Maintenance Check List .......91
3.5. Resetting the P/M(Preventive Maintenance) Counter .........93
3.6. Lubrication Point List ..............................94
3.7. Updating the Firmware ...........................97
3.8. Adjusting the Printer Registration,LSU Image Side to Side .......................108
3.9. Calibrating the LCD ..............................110
Troubleshooting ..................................1114.1. Initial Troubleshooting Flowchart..........111
4.2. Improper LCD Display ..........................112
4.3. Printed Copy Quality Problems.............113
4.4. Document Feeder (ADF) ......................131
4.5. Troubleshooting the LAN Interface .......136
4.6. Error Codes (For Copier) ......................144
4.7. Information Codes Table(For Facsimile)......................................157
4.8. Diagnostic Codes (For Facsimile).........163
4.9. Troubleshooting (For Printer)................170
Service Modes ......................................172
5.1. Service Modes (For Copier)..................1725.2. Service Modes (For Facsimile) .............203
System Description ............................. 2336.1. Printing Process ................................... 233
6.2. Precaution with Consumables.............. 234
6.3. New Image StabilizingTechnology....................... .................... 236
6.4. Mechanical Operation .......................... 2396.5. Automatic Document Feeder ............... 241
6.6. Receive Mechanism............................. 244
6.7. Glossary of Electrical Abbreviations ....................................... 254
Installation ............................................. 2617.1. Precautions During Set Up................... 261
7.2. Unpacking ............................................ 263
7.3. Installation Procedure .......................... 263
7.4. Adjustment ...........................................271
Options and Supplies .......................... 2738.1. Service Notes "Firmware Update"
for PCL-IPX/SPX or PS-IPX/SPXOption Installation(For DP-2330/3030) ............................. 273
8.2. Service Notes "Firmware Update"for PCL or PS Option Installation(For DP-2310/3010) ............................. 277
8.3. Installing the Printer Controller Module
for GDI-IPX/SPX (DA-GC601) ............ 2818.4. Installing the Printer Controller Module
for PCL6 (DA-PC300) ......................... 283
8.5. Installing the Printer Controller Modulefor PCL6-IPX/SPX (DA-PC301) .......... 285
8.6. Installing the Printer Controller Modulefor PS / PCL6 (DA-MC300) ................. 287
8.7. Installing the Printer Controller Modulefor PS / PCL6-IPX/SPX(DA-MC301) ........................................ 289
8.8. Installing the Network Scanner Module (DA-NS600)............................. 291
8.9. Installing the Network Scanner Module for DDS (DA-NS601) .............. 293
8.10. Installing the Internet Fax / E-MailModule (DA-NF600) ............................. 295
8.11. Installing the Fax CommunicationBoard (DA-FG300) ............................... 299
8.12. Installing the Hard Disk Drive Unit(DA-HD30) ........................................... 308
8.13. Installing the Accounting Software(DA-WA10) ........................................... 315
8.14. Installing the DD Server Software(DA-WS20) ........................................... 316
7/27/2019 Panasonic Dp2310 Service Manual
10/485
Table of Contents
10
8.15. Installing the Expansion F-ROMBoard (DA-EM600) ...............................317
8.16. Installing the Sorting Image Memory16 / 64 / 128 MB(DA-SM16B / 64B / 28B).......................319
8.17. Installing the Expansion Flash Memory
Card 4/8 MB (UE-410047/410048).......3218.18. Installing the 3rd Paper Tray
(DA-DS303) / 4th Paper Tray(DA-DS304) and the Stand for 4-Paper Tray Configuration (DA-DA230-PA)for DP-2310/3010 .................................322
8.19. Installing the 3rd Paper Tray(DA-DS305) / 4th Paper Tray(DA-DS306) and the Stand for 4-Paper Tray Configuration (DA-DA230-PA)for DP-2330/3030 .................................326
8.20. Installing the Deluxe Stand(DA-DA310 / DA320) for USA Only ......330
8.21. Installing the Stand(DA-DA310-PA / DA320-PA)for DP-2310/3010 .................................332
8.22. Installing the Stand(DA-DA311-PA / DA321-PA)for DP-2330/3030 .................................334
8.23. Installing the 1-Bin Finisher (DA-FS300)...........................................336
8.24. Installing the Exit Tray [Inner](DA-XN200) for DP-2310/3010.............342
8.25. Installing the Exit Tray [Inner](DA-XN201) for DP-2330/3030.............344
8.26. Installing the Exit Tray [Outer](DA-XT200)...........................................346
8.27. Installing the Automatic DocumentFeeder (DA-AS200) and the Inverting
Automatic Document Feeder (DA-AR250) for DP-2310/3010.............348
8.28. Installing the Automatic DocumentFeeder (DA-AS201) and the Inverting
Automatic Document Feeder (DA-AR251) for DP-2330/3030.............354
8.29. Installing the Platen Cover (DA-UC200) ..........................................360
8.30. Installing the Key Counter HarnessKit (DA-KH200) .....................................361
8.31. Installing the Dehumidifier Heater Kit(DZTQ000048).....................................363
8.32. Installing the Dehumidifier Heater Kit(DZTQ000049).....................................371
8.33. Replacing the OPC Drum .....................383
8.34. Replacing the Laser Unit (LSU)............387
General Network Information ............. 3919.1. Network Protocol.................................. 391
9.2. Layer Functions and Technology ......... 393
9.3. Network Layer ...................................... 397
9.4. Transport Layer.................................... 401
9.5. Upper Layer ......................................... 4039.6. SMTP
(Simple Mail Transfer Protocol)............ 408
9.7. ITU T.37 and RFC2305........................ 409
9.8. Communication Protocols .................... 415
9.9. POP(Post Office Protocol Version 3) ........... 418
9.10. Troubleshooting from a PC ..................421
9.11. Verifying the Configuration and Mail Account Type (SMTP or POP) ............. 422
9.12. Dynamic Host Configuration Protocol(DHCP) - Extended Feature................. 423
9.13. Message Disposition Notifications(MDN) - Extended Feature................... 426
9.14. Lightweight Directory Access Protocol(LDAP) - Extended Feature........... ....... 430
9.15. Lightweight Challenge-responseMechanism POP (APOP)- Extended Feature .............................. 430
9.16. SMTP Service Extensionfor Authentication (SMTP Auth)
- Extended Feature .............................. 4329.17. Direct Internet Fax XMT
- Extended Feature .............................. 434
Schematic Diagram ............................. 43510.1. General Circuit Diagram....................... 435
10.2. Finisher Circuit Diagram....................... 436
Finisher Option (DA-FS300) ................ 43711.1. General Description ............................. 437
11.2. Maintenance and Inspection ................ 44011.3. Operation and System
Description ........................................... 450
7/27/2019 Panasonic Dp2310 Service Manual
11/485
11
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
1 Specifications Table1.1. Copy Function
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
Basic Specifications1 Type Desktop2 Platen Fixed3 Original Position
Platen Left / Rear ADF / i-ADF Left / Center
4 Recording Paper Path Center 5 Face Up / Face Down Face Down6 Drum Organic Photo Conductor (OPC)7 Copy Process Dry Electrostatic System
8 Developing Process Dry Dual Components9 Toner Recycle No10 Fusing System Heat & Pressure
11 Max Original Size Ledger (11 x 17 in) / A3 (297 x 420 mm)
12 Paper Size
Paper Tray
LDR, LGL, LTR, LTR-R, INV-R For USA and Canada
A3, A4, A4-R, A5, A5-R, B4, FLS For EUFLS = 8 x 13 in, 8.5 x 13 in A3, B4, A4, A4-R, B5, B5-R For Other Destinations
Bypass
LDR, LGL, LTR, LTR-R, INV-R For USA and Canada
A3, A4, A4-R, A5, A5-R, B4, FLS For EUFLS = 8 x 13 in, 8.5 x 13 in A3, B4, A4, A4-R, B5, B5-R For Other Destinations
Bypass Envelope No13 Warm-up Time Approx. 35 sec 68 F (20 C)
14 First Copy Time Less than 4.5 sec
From Platen/ Letter/ A4Portrait/ 1st Paper Tray.Period between Start Key ispressed and Paper exits to
the lower Inner tray.When LSU is ready.15 Copy Speed
Ledger / A3 15 / 16 cpm 18 / 19 cpm
From 1st Paper Tray, exit toLower Inner Tray andContinuous Copy.
Legal / B4 / FLS 17 / 17 / 18 cpm 21 / 21 / 23 cpmLetter-R / A4-R 20 / 19 cpm 25 / 24 cpmLetter / A4 23 cpm 30 cpmInvoice-R / A5 / A5-R 23 cpm 30 cpm
16 ZoomEnlargement Selected Original size / Copy size
Reduction Selected Original size / Copy sizeZoom 25 - 400% 1% Step
7/27/2019 Panasonic Dp2310 Service Manual
12/485
12
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
17 Paper Feed Front Loading Universal Paper TrayPaper Tray
Capacity 550 sheets x 2
USA and CanadaLTR : 20 lb (75 g /m 2)
Other Destinations A4 : 80 g /m 2
Auto Size Setting No
Low Level Warning Empty OnlyBypass
Capacity 50 sheets Auto Size Setting Yes
Paper Capacity(Std. Configuration)
1,150 sheets
18 Acceptable Paper WeightPaper Tray 16-24 lb / 60-90 g /m2
Sheet Bypass 15-35 lb / 55-133 g /m2
19 Multi Copy Range 999 sheets20 Gradation
Text Bi-LevelText / Photo 256 steps Halftone by Error DiffusionPhoto 256 steps
21 Resolution 600 dpi Scanning and Printing.
22 Standard Sorting MemorySize
16 MB
23 Standard Page Memory Size 32 MB24 Exit Tray Capacity Standard: 250 sheets25 Color No26 Dimensions
(W x D x H) 23.58 x 27.83 x 27.44 in(599 x 707 x 697 mm)
H: To Platen Glass.
27 Operating Space
(W x D) 38.50 x 27.83 in(978 x 707 mm)
Includes Bypass Paper Tray.
28 Weight158.73 lb (72 k g ) Main Unit180.78 lb (82 k g ) Main Unit with i-ADF mounted
Options1 Paper Feed System Max. 550 sheets x 4
550 sheets 3rdPaper Feed Module
Yes Motor is mounted.
Paper Size Detection Manual Control Panel SelectableLow Level Paper Warning Empty Only
550 sheets 4thPaper Feed Module
Yes Motor is not mounted.
Paper Size Detection Manual Control Panel SelectableLow Level Paper Warning Empty Only
Max. Paper Capacity 2,250 sheets
USA and CanadaLTR : 20 lb (75 g /m 2)
Other Destinations A4 : 80 g /m 2
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
13/485
13
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
2 CabinetStand for 4-Paper Tray Configuration
Option Base Plate with Casters
Stand for 3-Paper Tray Configuration
Option Low Plain Stand
Stand for 2-Paper Tray Configuration
Option High Plain Stand
3 Platen Cover Option For EU and Other Destinations
Free Stop Yes From 30 to 70 degrees.4 ADF
Single Side Type Option For EU and Other Destinations
Original Set Face UpScanning Method Sheet Through
Capacity (Original) 50 sheets
USA and CanadaLTR : 20 lb (75 g /m2)
Other Destinations A4 : 80 g /m2
SADF Mode YesFree Stop Yes From 30 to 70 degrees.
5 Inverting ADF (i-ADF)
Duplex TypeStandard For USA and Canada
OptionFor EU and Other Destinations
Original Set Face UpScanning Method Sheet Through
Capacity (Original) 50 sheets
USA and CanadaLTR : 20 lb (75 g /m2)
Other Destinations A4 : 80 g /m2
SADF Mode Yes Available for single sidescanning only.
Free Stop Yes From 30 to 70 degrees.6 Exit Tray (Inner)
Tray Position Inner Number of Bins 1Face Up / Face Down Face DownBin Capacity Upper / Lower Bins: 250 sheets
Multi Tray Function Option (Inner 2-way)
Requires the Optional ExitTray (Inner).Max. 3 way using OptionalExit Tray (Outer) or Finisher.
Shift Tray Function No
7 Finisher Option Not available with Exit Tray(Outer).
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
14/485
14
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
Tray Position Outer Number of Bins 1Face Up / Face Down Face DownBin Capacity 500 sheets LTR, LTR-R, A4, A4-R, B5
250 sheets LDR, LGL, A3, B4, FLS
Multi Tray Function YesMax. 3 way using OptionalExit Tray (Inner) and Exit Tray(Outer) or Finisher.
Shift Tray Function Yes
Staple Function Yes
No Manual Stapling.Not available with Rotation.Not available with INV, INV-R,
A5, A5-R or B5-R.Stapler Capacity 3,000 pins
Max. Number of PagesStapled 30 sheets / set
LTR, LTR-R, A4, A4-R, B5 :30 sheetsLDR, LGL, A3, B4, FLS: 20sheets
Staple Position Rear / Upper 1 PositionPunch Function No
8 Exit Tray (Outer) Option Not available with Finisher.Tray Position Outer Number of Bins 1Face Up / Face Down Face DownBin Capacity 250 sheets LTR / A4
Multi Tray Function Yes Max. 3 way using OptionalExit Trays (Inner and Outer).
Shift Tray Function No
9 Dual-Path Exit Guide Unit Standard For Exit Tray (Inner or Outer),Finisher and Duplex printing.
10 Paper Transport Unit StandardTo be used for Exit Tray(Outer), Finisher and Duplexprinting.
11 Automatic Duplex Unit Standard12 Counter
Key Counter Capability Option The Harness Kit contains onlyHarnesses, Bracket and aScrew.
13 Dehumidifier Option Supplied as a Service Part.14 Sorting Image Memory
Optional Image Memory 1(16MB)
Yes Unit comes standard with16MB.1-Slot available for anOptional Image Memorymodule.
Optional Image Memory 2(64MB)
Yes
Optional Image Memory 3(128MB)
Yes
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
15/485
15
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
15 Hard Disk Drive Option
Additional Optional SortingImage Memory (Minimum 16MB) is required for the HardDisk Drive to function. (For Tandem, Remote Copy, etc.)
Features1 Automatic Features
Auto Magnification Selection Yes Auto Paper Selection Yes Auto Paper Tray Selection Yes
Auto Start Yes Reservation while Power OnInitial
Energy Saver Automatically enters theSleep or Shutdown Modeafter 15 minutes from the
Standby or Energy Saver Mode.Manually enters the EnergySaver Mode by pressing theEnergy Saver key.Sleep or Shutdown mode iscontrolled by the GeneralFunctions setting.
Standby Mode Yes (140Wh)
Energy Saver Mode Yes (28W)
Sleep Mode Yes (18W) Turns Off the Heater Power.
Shutdown Mode
Yes (3W)100 VAC Power SupplyNetwork Function not
available
Yes (4W)220 VAC Power SupplyNetwork Function notavailable
Remote Diagnostic Yes
Requires the FaxCommunication Board(DA-FG300) option or theInternet Fax / E-MAIL Module(DA-NF600) option.
Machine Stops when Out of Toner
Yes PPC Function
2 Additional FeaturesLow Level Paper Warning Empty OnlyPhoto Mode Yes 256 steps
Original Detection Release Yes Manually overridden whenusing the Original Size keys.Edit / Effects
Book Mode YesEdge Mode YesMargin Mode YesX-Y Zoom Yes 25 - 400%
Stamping
Page, Date, Issue Yes Available only when using the ADF.
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
16/485
16
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2-Sided Copy YesInverse Mode (Negative /Positive)
Yes
Centering Mode Yes With Digital Sky Shot
Mirror Mode NoImage Repeat YesOthers (Inverting ADF &
ADU)
2-Page Copy Mode Yes LDR LTR x 2
(A3 A4 x 2, B4 B5 x 2)2 in 1 Yes4 in 1 Yes6 in 1 Yes For USA and Canada
8 in 1 Yes For EU andOther Destinations
Booklet Mode YesCopy from four 1-Sidedpages to 1 Booklet Modesheet.
Duplex Copy1 2 Yes2 1 Yes Available only when using the
i-ADF.2 2 YesBook 2 Yes
1st Page BLANK Yes 1 2/2 1/2 21st Page IMAGE Yes Book 2
Image Rotation (90 or 270 ) YesElectronic Sorting YesRotation Sorting YesInsertion Job
Cover Mode Yes Available when using the ADFor i-ADF.
Page Insertion Mode YesOHP Interleave Mode YesPresentation Mode Yes
Department Counter Yes 300 Departments
ADF
Multi Size Feed YesLDR and LTR, LGL andLTR-R, A3 and A4, B4 andB5, A4-R and A5
JOB Build and SADFMode
Yes
Original Counter NoJob Memory Yes 5 Jobs in MemoryJob Time Display YesConcurrent Copy Yes 12 Concurrent Copy Jobs
Tandem Copy Mode YesRemote Copy Mode YesScan Once Print Many Mode Yes
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
17/485
17
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
Job Complete Notice YesTrial Copy Mode YesWeekly Timer YesFunction Mode Yes
Interrupt YesElectronic Counter YesDigital Sky Shot Mode YesCheck / Slip Mode Yes
3 Control PanelDisplay Wide Touch Panel LCD
Status Lamp YesGREEN : Scanning /
PrintingRED : Alarm / Warning
Key
Original Size YesCopy Size YesKeypad YesClear YesStop YesStart YesEnergy Saver YesMulti Size Feed NoSort / Finish NoFunction Mode Yes
Original DetectionRelease
No
Interrupt YesReset YesOne-Touch key No
Mode Change Yes Copier / Printer / NW Scanner / Fax and Internet Fax Mode
LCD Main Indication
Message Language(Default)
English (American) For USA and Canada
Specified Language For EU and Other
DestinationsOriginal Size / ImageIndication
Yes(without Image)
Paper Size / ImageIndication
Yes(without Image)
Paper Tray Selection YesSelected Paper Tray /Tray Status
Yes
Original Mode Selection Yes Text / Text-Photo / PhotoCopy Density Selection Yes
Setting Confirmation YesFunction Classification YesZoom Magnification Yes
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
18/485
18
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
Number of Copies YesJOB Build and SADF /Multi Size Feed Mode
Yes
Error Code Yes
Finishing YesWarning Indicators Yes Add Toner YesToner Waste Container Full
Yes
Add Paper (No Paper) Yes Add Paper (Under 50 sheets)
No
Paper Jam Indication YesPaper Jam Location Yes
Service Alert Call YesUser Error YesMachine Error YesHistory of Jam Errors Yes
4 Main UnitTotal Counter Yes (Standard) Mechanical Counter Max. Weight of Documentson the Platen Glass
11.02 lb (5 k g )
ADF with Document Guide YesClip Pocket Yes
Operating InstructionsPocket No
Warning / Caution Label Specified Language5 Optical System
Original Detection Method Reflective Photo Sensor TypeScanning Method 600 dpi CCDDehumidifier Yes Supplied as a Service PartMechanical Multi CopyMode
No
6 Process System
Type Separate OPC Unit andDeveloper Unit TypeToner 15 kDrum Life 60 kDeveloper Life 120 kToner Waste Container YesDehumidifier Yes Supplied as a Service Part
Manual Add Toner YesManually adds toner to thedeveloper (up to TDC threshold)
Efficiency1 Productivity ADF Productivity (LTR / A4)
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
19/485
19
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
ADF 100%Inverting ADF 100%
ADU Copy Productivity(LTR / A4) Throughput
When exiting to lower Inner Tray from 1st Tray.When LSU is ready.
Transport Method Stack less1 21 copy 70% 57%5 copies 90% 80%10 copies 95% 85%
PM Cycle1 PM Cycle
Major PM 120 kMinor PM (Cleaning) 60 k
Packing Configuration
1 Packing Dimension 28.58 x 32.91 x 42.91 in(726 x 836 x 1090 mm)
2 Packing Weight 218.26 lb (99 kg)3 Accessories
Process Unit YesDeveloper NoToner NoToner Waste Container NoOuter Tray No OptionOperating Instructions Yes
Power Supply
1 Power Requirement
99 - 138 VAC 47 - 63 HzSingle phase
100 VAC Power Supply
180 - 264 VAC 47 - 63 HzSingle phase
220 VAC Power Supply
2 Power Consumption Less than 1500 WAmbient Conditions
1 Temperature 50 - 80 F / 10 - 30 C2 Relative Humidity 30 - 80%
3 Safety
UL1950 / CSA C22.2 No.950 For USA and Canada
EN60950 For EU andOther Destinations
4 Energy Saver Energy Star Compliant
5 EMI Class A computing device in FCC RulesPart 15 For USA and Canada
6 Lead Free Solder (PbF) This Product uses Lead Free (PbF)PCBsRefer to the Parts Manual for details
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
20/485
20
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
1.2. Fax, Printer and Internet Fax Functions
1.2.1. Fax Function
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
Main Specifications
1 Compatibility G3 ITU-T Std & Non-Std2 PSTN Line Port Yes 1-Line Only3 Leased Line Port No4 V.24 Line Port No5 Modem Speed 33.6 - 2.4kbps T.30/V.34/V.17/V.29/V.27ter 6 Coding Scheme JBIG/MMR/MR/MH7 ECM Yes Conforms to ITU-T Rec. T.30 ECM8 Short Protocol Yes (B, D)
9 Transmission Speed Approx. 3 sec ITU-T Image No. 1(A4, Std Resolution)
10Communication Resolutiondpi x lpi (pels/mm x lines/mm)
Transmission Std. 203 x 98 (8 x 3.85)Fine 203 x 196 (8 x 7.7)S-Fine 203 x 391 (8 x 15.4)
406 x 391 (16 x 15.4)600dpi 600 x 600 dpi
Reception Std. 203 x 98 (8 x 3.85)Fine 203 x 196 (8 x 7.7)S-Fine 203 x 391 (8 x 15.4)
406 x 391 (16 x 15.4)600dpi 600 x 600 dpi
600 dpi communication is onlyavailable between WORKiO DP-2310/3010/3510/4510/6010 and other T.30compliant machines.
Scanner Mechanism1 Scanning Device CCD (ADF / Platen)2 Scanning Speed (ADF)
Resolution Vertical Horizontal
A4, Scanned in Vertical or HorizontalDirection.Excluding Initializing Time and ADFslipping factor.
Std: 203 x 98 (8 x 3.85)dpi x lpi (pels/mm x lines/mm)
0.6 sec 0.4 secFine: 203 x 196 (8 x 7.7)dpi x lpi (pels/mm x lines/mm)S-Fine: 406 x 391 (16 x15.4) dpi x lpi (pels/mm xlines/mm)
1.1 sec 0.8 sec
600dpi: 600 x 600 1.7 sec 1.2 secScanning Speed (Platen)Resolution Vertical Horizontal600dpi: 600 x 600 1.7 sec 1.2 sec
3Scanning Resolutiondpi x lpi (pel/mm x lines/
mm)
Std 203 x 98 (8 x 3.85)Fine 203 x 196 (8 x 7.7)S-Fine 203 x 391 (8 x 15.4)
406 x 391 (16 x 15.4)600dpi 600 x 600 dpi4 Document Size (Max.) ADF: Ledger / A3
7/27/2019 Panasonic Dp2310 Service Manual
21/485
21
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
5 Effective Scanning Width LDR (11.5 in) / A3 (292 mm)6 A3 Size TX/RX Yes Conforms to ITU-T A37 Reduction XMT Yes A3 to B4 / A3 to A4 / B4 to A48 ADF Capacity 50 sheets Face-Up, feed from top page
9 Collation Stack Yes Face DownPrinter Mechanism
1 Recording Method LP
2 Recording Speed 23 / 30 ppm(A4 Horizontal)
Recording Speed attained after the 1stcopy.
3 Recording Resolution Fax 600 x 600 dpi
4 Recording Paper Size Ledger / Legal / Letter / A3 / B4 / A4 / A5
Invoice : Not supported.Ledger size is transmitted as A3 sizefor N. American models. If A3 isreceived, approx. 1" of image on bothedges are not printed on Ledger sizepaper.
5 Effective Printing Width 11.4 in (289 mm) Conforms to ITU-T A36 Recording Paper Capacity 1,150 sheets Optional max. 2250 sheets7 Collation Stack Yes Face Down
8 Consumable Toner Bottle, Developer,OPC Drum and Staples
Fax Memory
1 Standard Memory
DP-2330/3030:3 MB (180 pages)
DP-2310/3010:
2 MB (120 pages)
Flash ROM, ITU-T Image No.1(A4, Std Resolution)
2 Optional Memory 4 MB (+320 additional pages)8 MB (+640 additional pages)Expansion Flash Memory Card, usingITU-T Image No.1 (A4, Std Resolution)
Dual Operation1 Multi Task Operation Yes2 Direct XMT Reserve Yes3 Memory XMT Reserve Yes
4 Number of Memory JobFiles
Yes Max. 50 files
Dialing/Telephone Features
1 Auto Dialers 200 StationsPlus an additional 800 stationsavailable to select from, when theoptional Hard Disk Drive (DA-HD30) isinstalled.
2 Phone Book DirectorySearch Dialing
Yes
3 Total Auto Dialers 270 Stations 200 Address Book + 70 Full Number Dialing
4 Program Dials 125 Max. Tel Number Digits 36
6Max. Station NameCharacters 15
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
22/485
22
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
7 Full Number Dialing(Buffered Dialing)
Yes Max. 70 stations
8 Direct Dialing(Monitor Dialing)
Yes Voice mode
9 Automatic Redialing Yes Up to 15 times at 0 to 15 min. intervals10 Manual Redialing Yes Pressing the REDIAL/PAUSE button11 Line Monitor Speaker Yes12 Chain Dialing (Hybrid Dial) Yes In Monitor Dialing mode only13 Pulse / Tone Dialing Yes 10 pps / DTMF14 Pulse to Tone Change No15 Flash Key Yes16 Handset No
Transmission Features1 Direct Transmission Yes
2 Memory Transmission Yes Page Retransmission3 Quick Memory
TransmissionYes
4 Multi-Station Transmission(Sequential Broadcasting)
Yes Max. 270 stations
5 Direct DeferredTransmission
No ADF Deferred Transmission
6 Deferred Transmission Yes Max. 50 timers
7 Deferred Multi-StationTransmission
Yes
8 Priority Direct Transmission Yes Priority ADF Transmission
9 Priority MemoryTransmission
No
10 Batch Transmission Yes Real Time (up to 5 Files)
11 90 Degree RotationTransmission
Yes
12 Cover Sheet Yes13 Confidential Mail Box No14 Multi-Copy Transmission No
15 Memory Back-Up YesFAX : Back-up with Flash Memory.Copy / Printer : No Back-up with D-RAM
16 Duplex Scanning Yes With Inverting ADF (i-ADF)Reception Features
1 Substitute Reception Yes
2 Fixed Reduction YesLTR/A4/LGL: 70 - 100%(in 1% Steps),Top & Left Alignment
3 Auto Reduction YesLTR/A4/LGL: 70 - 100%(in 1% Steps),Top & Left Alignment
4 Overlap Printing Yes Page End Approx. 0.51 in (13 mm)5 Receive to Memory Yes
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
23/485
23
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
6 Distinctive Ring Detector (DRD)
No
7 90 Degree RotationReception
Yes
8 Duplex Printing YesPolling
1 Polling Yes2 Turnaround Polling No3 Multi-Station Polling Yes Max. 270 stations4 Deferred Polling Yes Max. 50 timers
5 Deferred Multi-StationPolling
Yes Max. 50 timers / 270 stations
6 Direct Polling Tx No7 Memory Polling Tx Yes 1 File
8 Preset Polling Password Yes9 Temporary Polling
PasswordYes
10 Continuous Polling YesConvenience
1 Panel Display Wide Touch Panel Display2 Voice Contact No3 Edit File Mode Yes With View Mode4 Incomplete File Save Yes With View Mode5 Automatic Cover Sheet Yes
Certainty1 Verification Stamp Yes2 Header / Total Page Print Yes3 Transaction Journal Yes 200 Transactions / with View Mode4 Comm. Journal Yes With Image Data5 Last Ind. XMT Journal Yes
List Printouts1 One-Touch List -2 ABBR. No. List -3 Program List Yes
4 Address Book Search List Yes Auto Dialer List5 Fax Parameter List Yes6 File List Yes With View Mode7 Ind. XMT Journal Yes8 Directory Sheet No
Identifications1 Logo Yes 25 Characters2 Multiple Logo No3 Character ID Yes 16 Characters4 Numeric ID Yes 20 Digits
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
24/485
24
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
Special Communications1 Password XMT / RCV No2 Selective Reception No TSI Check3 Relay XMT Request No
4 Relay XMT Center No5 Confidential XMT / Polling No6 Confidential Center No7 Mailbox XMT / Polling No8 Mailbox Center No9 File XMT No
10 Fax Forward Yes Received File Transfer (Only with Internet FAX Option)
11 Sub-Address XMT Yes T. Routing12 Sub-address RCV No
13 OMR-XMT NoStandards
1 PSTNFCC Part 68: 1997 / Industry
CanadaNo. CS-03: Issue 8 1996
Others1 Fax Access Code Yes2 PIN Code Access Yes For USA and Canada only3 Intelligent Redial (AI) Yes 5 Files4 Department Code Yes 300 Departmental Codes
5 Power Saver Mode Yes6 Self Diagnostic Function Yes
7 Remote DiagnosticFunction
Yes
8 Check & Call Function Yes9 V.24 / Encryption Interface No
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
7/27/2019 Panasonic Dp2310 Service Manual
25/485
25
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
1.2.2. Printer Function
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
Interface1 Centronics Parallel I/F No
2 LAN (Network) Ethernet 10Base-T/100Base-TX
3 USB Port Yes USB4 IEEE-1394 No
Printer Function
1 Printing SizeLDR, LGL, LTR, LTR-R, INV-R For USA and Canada
A3, A4, A4-R, A5, A5-R, B4, FLS For EU A3, B4, A4, A4-R, B5, B5-R For Other Destinations
2 Bypass Yes3 Stapling Yes Requires Optional Finisher
4 Printing Resolution (dpi) 600 x 600(with Smoothing)Selectable 600 dpi, with Smoothing,the results are similar to PS3 / PCL6Printers (1200 dpi Interpolated).
5 Interface USB / Ethernet
6 OSWin 98 / Win Me /
Win NT 4.0 / Win 2000 /Win XP / MAC 8.6-10.1
MAC 8.6-10.1 is PS only.
7 GDI Yes8 PDL (PCL6) Yes Requires Optional PCL6 Emulation Kit.
9 PDL (PS3) Yes Requires Optional PS / PCL6
Emulation Kit10 Duplex Printing Yes Custom Size/Post Card Size is notavailable.11 Collation Stack Yes12 Status Monitor No13 Network Printing Yes14 Network Status Monitor Yes15 Smoothing Yes16 Applicable PC IBM PC, AT or Compatible, MAC MAC is PS only.17 Multi-Task Operation
Printing while Fax-XMTfrom Memory Yes
Printing while Fax-RCVinto Memory
Yes
Fax-XMT from Memorywhile Printing
Yes
Fax-RCV into Memorywhile Printing
Yes
18 Output to separate tray for Printing, Fax, Copy
Yes
19 Font YesRequires Optional PCL6 or PS / PCL6Emulation Kit
20 Security Print Yes Requires Optional HDD UnitMax. 100 Boxes
7/27/2019 Panasonic Dp2310 Service Manual
26/485
26
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
1.2.3. Network Scanner Function
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
Interface1 Centronics Parallel I/F No
2 LAN (Network) Ethernet 10Base-T/100Base-TX
3 USB Port No4 IEEE-1394 No Firewire
Network Scanning Function1 Scanning Device CCD (i-ADF / Platen)
2 Scanning Speed (ADF) 30 opmITU-T Image No. 1 (A4, StdResolution), JBIG, 600 dpiExcluding Data XMT Time.
3 Halftone 256 Halftone Shades With Error Diffusion
4 Max. Document Size Ledger, A3
5 Scanning Resolution(dpi)
600 x 600300 x 300150 x 150
Selectable, 600 dpi Optical Scanner
6 OS Win 98 / Me /Win NT 4.0 / Win 2000 / XP
7 2-Sided Scanning Yes With i-ADF.
8 File Format Mult-page TIFF / PDF TIFF can also be converted to PDFwith the PDMS Software
9 Completion Notice Yes Auto Pop-up on the PC Screen(requires Network Status Monitor -installed with PDMS Software)
10 Protocol TCP/IP, Non-Std
7/27/2019 Panasonic Dp2310 Service Manual
27/485
27
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
1.2.4. Internet Fax Function
ItemsDescription
RemarksDP-2310/2330 DP-3010/3030
Main Specifications1 Communication Protocols SMTP / POP3 / MIME
2 Max. Modem Speed NA3 Coding Scheme JBIG/MMR/MR/MH
4 File Format TIFF / PDF
Selectable(PDF format can be used for Scan-to-Email when sending to a PC.However, since current Internet Faxstandards do not support this fileformat, it cannot be used for sendingto another Internet Fax machine)
5 Line Interface RJ-45 Ethernet LANScanner Mechanism
1 Max. Document Size Ledger, A32 Effective Scanning Width 11.4 in (289 mm)
3 Scanning Resolutiondpi x lpi (pel/mm x lines/mm)
Std 203 x 98 (8 x 3.85)Fine 203 x 196 (8 x 7.7)S-Fine 203 x 391 (8 x 15.4)
406 x 391 (16 x 15.4)600dpi 600 x 600 dpi
LAN: 600 dpi, 16 x 15.4 ScanningResolution is available withParameter setting
Printer Mechanism1 Printing Resolution 600 dpi2 Effective Recording Width 11.4 in (289 mm)
Transmission Features
1 Multi-Task Operation Yes Simultaneous operation of G3 Faxand LAN is available.
2 Memory Transmission Yes
3 Sequential Multi-StationTransmission
Yes
4 Simultaneous Multi-StationTransmission YesMax. 270 stations(200 Address Book + 70 Full Number Dialing)
5 Sender Selection Yes
6 G3 / Email MixedBroadcasting Yes
7 Deferred Transmission Yes
8 Fax Forward Yes Received File Transfer, only withInternet FAX Option
9 Sub-address RCV Yes Inbound Routing, only with InternetFAX Option
10 Mail Header Email Header Print Selection Yes All or From / To / Subject onlySubject Line Random Entry
7/27/2019 Panasonic Dp2310 Service Manual
28/485
7/27/2019 Panasonic Dp2310 Service Manual
29/485
29
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
1.3. System Combination
Document SensorMotor
Scanner Unit(SDR PC Board)
Expansion FlashMemory Card4 or 8M
Main PC Board(SC PC Board)
Image Memory
Either Option
Electronic Sorting Memory
Dual-Path Exit GuideUnit
Paper Transport Unit
2nd Paper Tray (CST2 PC Board)
3rd Paper Tray (CST3 PC Board)
4th Paper Tray (CST2 PC Board)
1-Bin Finisheror
Exit Tray (Outer)
Motor, Sensor, SL
Solenoid, Sensor
DehumidifierHeater Kit
Option
Standard Configuration
Panel(PNL PC Board)
Key CounterHarness Option
16, 64, 128MB
Hard Disk Option
PCL6Emulation Option
PS/PCL6Emulation Option
NetworkScanner Option
Internet Fax/ E-Mail Option
USBInterface
Printer
10/100 EthernetInterface
MJR
Fax CommunicationOption (FXB)
SPC PC Board
Inverting ADF (i-ADF)
ADF PC Board
AutomaticDuplex Unit
IPC Board
(EXFD PC Board)
7/27/2019 Panasonic Dp2310 Service Manual
30/485
30
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
1.4. Options List Options
Option Name Option Number RemarksPrinter Controller Module for PCL6 DA-PC300
For DP-2310 / 3010Multi Page Description LanguageController Module for PS/PCL6
DA-MC300
Printer Controller Module for PCL6-IPX/SPX DA-PC301 For DP-2330 / 3030
(For USA and Canada, can also be usedfor DP-2310 / 3010 without IPX/SPX)Multi Page Description Language
Controller Module for PS/PCL6-IPX/SPX DA-MC301
Printer Controller Module for GDI-IPX/SPX DA-GC601For DP-2330 / 3030
Document Distribution System DA-WR10Network Scanner Module DA-NS600 For Network ScanningNetwork Scanner Module for DDS DA-NS601 For DP-2330 / 3030Internet Fax / E-Mail Module DA-NF600 Internet Fax/Email CommunicationFax Communication Board DA-FG300 G3 Fax Communication
Hard Disk Drive Unit DA-HD30 Additional Optional Sorting Image Memory(Minimum 16 MB) is required for the HardDisk Drive to function.(For Tandem, Remote Copy, etc.)
Expansion Board DA-EM600 F-ROM Board (8 MB)Expansion Flash Memory Card, 4 MB UE-410047
Additional Memory for Fax / Internet FaxExpansion Flash Memory Card, 8MB UE-410048Image Memory (16MB) DA-SM16B
For Electronic SortingImage Memory (64 MB) DA-SM64BImage Memory (128MB) DA-SM28B
DD Server Software DA-WS20 For DD Server Function Accounting Software DA-WA10 For Accounting Function1-Bin Finisher DA-FS300Exit Tray (Outer) DA-XT200Exit Tray (Inner) DA-XN200 For DP-2310 / 3010Exit Tray (Inner) DA-XN201 For DP-2330 / 3030Platen Cover DA-UC200 Available in Specified Destinations
Automatic Document Feeder DA-AS200For DP-2310 / 3010
Inverting Automatic Document Feeder DA-AR250 Automatic Document Feeder DA-AS201
For DP-2330 / 3030Inverting Automatic Document Feeder DA-AR2513rd Paper Tray DA-DS303
For DP-2310 / 30104th Paper Tray DA-DS3043rd Paper Tray DA-DS305
For DP-2330 / 30304th Paper Tray DA-DS306Stand (High) DA-DA310 Available in Specified Destinations
For DP-2310 / 3010Stand (Low) DA-DA320Stand (High) DA-DA311 Available in Specified Destinations
For DP-2330 / 3030Stand (Low) DA-DA321Base Plate with Casters DA-DA230 Available in Specified DestinationsKey Counter Harness Kit DA-KH200* DZTY000161 is not available by
Supply rout / policy change.
7/27/2019 Panasonic Dp2310 Service Manual
31/485
31
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
Supplies
Note:PCL6 is a Page Description Language of the Hewlett-Packard Company.PS3 is a Page Description Language of the Adobe Systems Company.
Available in Specified Destinations
Part Name Part Number RemarksToner DQ-TU15E 15 kStaple Cartridge FQ-SS32OPC Drum DQ-H60EDeveloper DQ-Z120E
7/27/2019 Panasonic Dp2310 Service Manual
32/485
32
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
1.5. External View1. Standard Configuration
2. With Optional System Console Configuration
3 3
. 8 6 i n ( 8 6 0
m m
)
2 7
. 4 4 i n ( 6 9 7
m m
)
23.58 in (599 mm) 27.83 in (707 mm)
Manufacturer's Name and Address Factory ID
Product complies with DHHS Rules 21CFR Subchapter J in effect at dateof manufacture.
(For USA Only)
Front View Right ViewLeft View
Top View
Rear View
CAUTION!
THIS PRODUCT CONTAINS A LITHIUM BATTERY. DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. DISPOSE OF USED BATTERIES ACCORDINGTO THE INSTRUCTIONS OF YOUR LOCAL SOLID WASTE OFFICIALS.
4 5
. 9 8 i n ( 1 1 6 8
m m
)
1 2 . 0 5 i n
( 3 0 8
m m
)
14.84 in(377 mm)
Front View Right ViewLeft View
Top View
Rear View
7/27/2019 Panasonic Dp2310 Service Manual
33/485
33
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
3. Space Requirements With Options
2 7
. 8 3 i n ( 7 0 7 m m
)
2 7
. 8 3 i n ( 7 0 7 m m
)
2 7
. 8 3 i n ( 7 0 7 m m
)
14.2 in (379 mm)
14.92 in (379 mm)
14.92 in (379 mm)
Copier + Finisher
Copier + Outer Exit Tray
Copier
3.94 in (100 mm)
3.94 in (100 mm)
10.83 in (275 mm)
14.84 in(377 mm)
9.88 in
(251 mm)
3.46 in (88 mm)
3.94 in (100 mm)
3.94 in (100 mm)
3.94 in (100 mm)
3.94 in (100 mm)
3 . 9
4 i n ( 1 0 0 m m
)
3.94 in (100 mm)
3.94 in (100 mm
3.94 in (100 mm)
51.65 in (1312 mm)
51.65 in (1312 mm)
51.65 in (1312 mm)
46.38 in(1178 mm)
60.67 in(1541 mm)
71.06 in(1805 mm)
15.94 in (405 mm)
15.94 in (405 mm)
15.94 in (405 mm)
23.58 in (599 mm)
23.58 in (599 mm)
23.58 in (599 mm)
3 . 9
4 i n ( 1 0 0 m m
)
3 . 9
4 i n ( 1 0 0 m m
)
7/27/2019 Panasonic Dp2310 Service Manual
34/485
34
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
1.5.1. Serial Number ContentsThe contents of the 11-digit Serial Number is as follows:
2 3 4 5 61
Sequential Production Number5-Digit Sequential Production Number
00001 ~ 99999 = 1 ~ 99,999 unitsA0001 ~ Y9999 = 100,000 ~ 329,976 units(Letters I and O are skipped)
3-Digit number or alphanumeric representation(Except Letters I and O)
For Example:= DP-2310-PU
= DP-3010-PU
Production Facility
Production YearStarting with Year 2001, the last 2-digits of the year isrepresented as: A ~ T
A : 01 (2001) K : 11 (2011)B : 02 L : 12C : 03 M : 13D : 04 N : 14E : 05 O : 15F : 06 P : 16G : 07 Q : 17H : 08 R : 18I : 09 S : 19J : 10 (2010) T : 20 (2020)
Production MonthA : January G : JulyB : February H : AugustC : March I : SeptemberD : April J : OctoberE : May K : NovemberF : June L : December
7 8 9 10 11
Model Number and Destination Code (Main Unit)
39J
39H = DP-2310-PB39K
=
DP-3030-PB
DP-3010-PB39L= DP-2330-PU= DP-3030-PU3ZF
3ZD = DP-2330-PB3ZE=3ZG
7/27/2019 Panasonic Dp2310 Service Manual
35/485
35
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
1.6. Control Panel
DP-2310/3010
DP-2330/3030
7/27/2019 Panasonic Dp2310 Service Manual
36/485
36
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
1.7. Fans and Motors
1.8. Clutches and Switches
Scanning Motor (201)
LVPS Fan (322)
LSU Fan (315)
Main Motor (907)
ADF Motor (1801)Transport Motor (1320)
Toner Motor (958)
Lift DC Motor (1152)
Fan (459)
ILS PCB (19124)(Front Cover Sensor)
Paper Feed RollerClutch (1105)
Paper Feed Roller
Clutch (1105)
Intermediate RollerClutch (957)
Sheet Bypass FeedRoller Clutch (1105)
Registration RollerClutch (957)
ADF RollerClutch (1788)
IntermediateClutch (969)
Feed 2 RollerClutch (1787)
Micro Switch (461)
7/27/2019 Panasonic Dp2310 Service Manual
37/485
37
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
1.9. PC Boards
CST2 PCB (1913)
DCB PCB (1906)HSU PCB (1974)
LVPS (1910)Optional LVPS (1912)
NFL PCB (1909)
RLB PCB (1917)
ACD PCB (1904)
ADF PCB (1907)PNL3 PCB (113)
EXFD PCB (1978)
MJR PCB (1915)
DC PCB (1905)FXB PCB (1916)
SDR PCB (1903)
PNL2 PCB (123)
CDS PCB (1986)
WTS PCB (1982)
SC PCB (1901)
HVPS (1911)
SPC PCB (1902)
LED PCB (1982)SNS PCB (1981)
PNL1 PCB (1908)
PNL4 PCB (114)
SNS PCB (1981)LFB PCB (1969)
CCD (207)
7/27/2019 Panasonic Dp2310 Service Manual
38/485
38
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2 Disassembly Instructions2.1. General Disassembly
Pertinent Disassembly Instruction sections are shown below.
7/27/2019 Panasonic Dp2310 Service Manual
39/485
39
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
2.2. Disassembly Instructions
2.2.1. Inverting-Automatic Document Feeder (i-ADF) Unit
(1) Open the ADF Cover (1831).(2) Remove 4 Silver Screws (B1).
(3) Lift the ADF Input Tray (1604).(4) Slightly pull the right edge of the ADF Rear
Cover upward.
(5) Release the Latch Hooks .(6) Remove the ADF Rear Cover (1601).
(7) Lower the ADF Input Tray back in place.(8) Disconnect the AMT Harness (1951) from the
Clutch.(9) Remove the Snap Ring (S9).
(10) Remove the ADF Roller (1728) Assembly.
(11) Remove the Snap Ring (S9).(12) Remove the Clutch (1788).
(13) Remove the Bushing (1621).(14) Remove the Rear ADF Guide (1725).
7/27/2019 Panasonic Dp2310 Service Manual
40/485
40
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(15) Remove the Snap Ring (S9).(16) Remove the Pin (744).(17) Remove the ADF Shaft (1724).(18) Remove the ADF Roller (1728).
(19) Remove the Snap Ring (S9).(20) Remove the Pre-Feed Roller Shaft (1730).(21) Remove the Pre-Feed Roller (1731).
(22) Remove 1 Silver Screw (B1).(23) Remove the ADF Front Cover (1637).Note:
Release 3 Latch Hooks in alphabetical order andin the direction as shown by each arrow.
(24) Remove 4 Screws (19).(25) Remove the Upper ADF Guide (1723).
(26) Remove the Snap Ring (S9).(27) Remove the Torque Limiter Bushing (1741)
and Torque Limiter Spring (1742).Note:
When reinstalling the Torque Limiter Assembly,ensure that the Torque Limiter Spring is placedinto the deeper slot of the Separation Roller.
(28) Remove the Separation Roller (1740).(29) Disconnect the APNT Harness (1956) and
remove Sensor (1045) (Original DetectionSensor).
7/27/2019 Panasonic Dp2310 Service Manual
41/485
41
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(30) Disconnect all Connectors on the ADF PCBoard.
(31) Remove 2 Screws (19).(32) Remove the ADF PC Board (1907).
(33) Remove 2 Screws (24).(34) Remove the ADF Motor (1801).
(35) Remove 6 Screws (19).(36) Remove the Sensor Bracket (1663).
(37) Remove 4 Screws (19).(38) Remove the Motor Bracket (1811) and Gear
Bracket (1802) Assemblies.Note:
Apply Molykote EM-50L Grease to all Gears andShafts except to the following: E26S35 Drive Gear (1805), E26S35 Gear F (3305), ADF Motor (1801),and the shafts of Drive Shaft 2 (1817) and ExitRoller (1751).
7/27/2019 Panasonic Dp2310 Service Manual
42/485
42
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
< Cleaning ADF Roller, Pre-Feed Roller, DriveRoller and Feed 2 Roller>
(1) Open the ADF Cover (1831).(2) Clean the ADF Roller (1728), Pre-Feed Roller
(1731), Drive Roller (1872) and the Feed 2Roller (1753) with a soft cloth, saturated withisopropyl alcohol.
< Cleaning Exit Roller and Inverting Feed Roller>
(3) Lift the ADF Input Tray (1604).(4) Open the ADF Exit Cover (1854).(5) Clean the Exit Roller (1751) and the Inverting
Feed Roller (1853) with a soft cloth, saturatedwith isopropyl alcohol.
7/27/2019 Panasonic Dp2310 Service Manual
43/485
43
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
2.2.2. Control Panel Unit
(1) Pull the Battery Holder (104) part of the wayout.
(2) Release the Latch and remove the BatteryHolder (104) out.
(3) Remove 6 Silver Screws (B1).(4) Remove the Left Platen Cover (514) and the
Right Platen Cover (516).(5) Remove 2 Silver Screws (B1).
(6) Slightly lift the Control Panel Assembly.(7) Disconnect 4 Harnesses on the PNL1 PC Board
(CN220, CN221, CN222 and CN224).(8) Remove 1 Screw (21) to disconnect the Ground
Connector .(9) Remove the Control Panel Assembly.
(10) Disconnect 4 Harnesses on the PNL1 PC Board(CN223, CN225, CN229 and CN230).
7/27/2019 Panasonic Dp2310 Service Manual
44/485
44
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(11) Remove 4 Screws (F10).(12) Remove the PNL1 PC Board (1908).
(13) Remove 7 Screws (F10).(14) Disconnect the Harness on the PNL2 PC Board
(CN251).(15) Remove the PNL2 PC Board (123).Note:
After reassembling the Control PNL2 PC Board,make sure that the Battery Holder isreinstalled.
(16) Disconnect the Harness on the INV PC Board(CN2).
(17) Remove 2 Screws (P5).(18) Remove the INV PC Board (129).
(19) Remove 2 Screws (P5).(20) Release 2 Latch Hooks and remove the Upper
Control Panel Cover (122).
7/27/2019 Panasonic Dp2310 Service Manual
45/485
45
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(21) Remove 1 Screw (P5).(22) Remove the PNL4 PC Board (114).
(23) Remove 4 Screws (P5).(24) Remove the PNL3 PC Board (113).
(25) Remove 2 Screws (H4).(26) Remove 2 Screws (H4).(27) Remove the LCD Module (128).
(28) Remove the Touch Panel (127).
7/27/2019 Panasonic Dp2310 Service Manual
46/485
46
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.2.3. Scanner Unit
(1) Remove the Left and Right Platen Covers (514, 516) and the Control Panel Assembly .(Refer to 2.2.2. )
(2) Remove 2 Screws (19).(3) Remove the Glass Assembly (557).
(4) Remove the Glass S (559).
(5) Holding by the center, slowly move the LampBase Assembly to the center of the Scanner Base Frame in the direction shown by the arrow.
(6) Remove 4 Screws (19).(7) Remove the F/R Scanner Frame (240).
7/27/2019 Panasonic Dp2310 Service Manual
47/485
47
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(8) Remove 2 Screws (19).(9) Remove the 2 Lamp Plate Springs (232).
(10) Disconnect the Harness on the LFB PC Board(CN181).
(11) Remove the Scanning Lamp (204).
(12) Remove 2 Mirror Plate Springs (230).(13) Remove Mirror 1 (264).Note:
Observe the position of the Mirror 1 beforeremoving it. The Black Mark on the Mirror,indicates non-reflective side. When reinstalling,
make sure the smooth side of Mirror 1 with theBlack Mark is pointing downwards.
(14) Disconnect 2 Harnesses on the Inverter PCBoard (CN1 and CN2).
(15) Remove 1 Screw (19).(16) Remove the Inverter Upper Cover (212).
(17) Remove 2 Screws (19).(18) Remove the Inverter PC Board (268).
7/27/2019 Panasonic Dp2310 Service Manual
48/485
48
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(19) Remove 2 Red Screws (D24).(20) Remove the FPC Cable Holder A (215)
Assembly.
(21) Holding by the center, slowly move the LampBase Assembly towards the left of the Scanner Base Frame.
(22) Disconnect the Harness on the LFB PC Board(CN181).
(23) Remove 1 Screw (19).
(24) Remove the FPC Cable Holder B (216) Assembly.
(25) Remove 2 Sliders on the Connectors.(26) Remove the FPC Cable (260).Note:
The Sliders must be reinstalled whenreassembling.
(27) Remove 4 Silver Screws (S6).(28) Open the Rear Cover .(29) Remove 4 Silver Screws (S6).
(30) Remove the Rear Right Cover (507) and theRight Rear Cover (518).
7/27/2019 Panasonic Dp2310 Service Manual
49/485
49
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(31) Remove the E-Ring (5Y).(32) Remove the Synchro Belt (208).
(33) Remove the MXL34 Pulley (217).(34) Remove 1 Screw (6P).(35) Remove the Fan (459).
(36) Disconnect the Harness on the Scanning Motor.(37) Remove 3 Screws (19).(38) Remove the Motor Bracket (249) Assembly.Note:
When reinstalling the Motor Bracket, tighten theupper screw first.
(39) Remove 2 Screws (36).(40) Remove the Scanning Motor (201).
7/27/2019 Panasonic Dp2310 Service Manual
50/485
50
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(41) Disconnect the Harness on the SC PC Board(CN106).
(42) Release 2 Latch Clips and remove the FerriteCore .
(43) Remove 3 Red Screws (D24).(44) Remove the CCD Assembly (207).
Note:When reinstalling the CCD Assembly, align thehole with the Red Mark on the CCD Assembly withthe hole on the Scanner Base Frame as illustratedand secure it with 3 Red Screws.
(45) Remove 1 Screw (6P).(46) Remove the CN Bracket (511) Assembly.
7/27/2019 Panasonic Dp2310 Service Manual
51/485
51
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(47) Remove 2 Screws (19).(48) Remove the SDR PC Board (1903).
(49) Remove 6 Screws (19).(50) Remove the F/R Scanner Frame (240).
(51) Remove 2 Red Screws (D24).(52) Remove the Rear Lamp Belt Lock (228).(53) Remove the Front Lamp Belt Lock (227).(54) Remove the Lamp Base Bracket (224)
Assembly.
(55) Remove the 3 Sliders (211).
7/27/2019 Panasonic Dp2310 Service Manual
52/485
7/27/2019 Panasonic Dp2310 Service Manual
53/485
53
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(3) Install the Mirror 2 Bracket (233) Assembly.(4) Reinstall the 2 Inner Timing Belts (202).
Note:The Bracket must be adjusted by moving ittowards the center until it stops against thenotches in the frame.
(5) While holding each side of the Bracket againstthe notch, secure the Rear Mirror Belt Lock (238) and the Front Mirror Belt Lock (236) with2 Screws (18).
(6) Install the Lamp Base Bracket (224) Assembly.Note:
The Bracket must be adjusted by moving ittowards the right edge until it stops against thenotches in the frame. Make sure that the Mirror 2Bracket Assembly is positioned in the notches in
the center of the frame.
(7) While holding each side of the Bracket againstthe notch, secure the Rear Lamp Belt Lock (228) and the Front Lamp Belt Lock (227) with2 Red Screws (D24).
7/27/2019 Panasonic Dp2310 Service Manual
54/485
7/27/2019 Panasonic Dp2310 Service Manual
55/485
55
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
2.2.4. Process Unit
(1) Open the Right Cover (1201).(2) Remove 1 Screw (6P).(3) Remove the Harness Cover (1525).(4) Unlock the Angled Rear Arm (1218) and
the Front Arm (1217).
(5) Open the Right Cover and hook the AngledRear Arm into the lower Hook Hole.
(6) Open the Front Cover (528).(7) Remove the Toner Waste Container (618).
(8) Remove the Toner Bottle (617).(9) Remove 1 Screw (19).
(10) Remove the Connector Cover (Clear Blue)(538).
7/27/2019 Panasonic Dp2310 Service Manual
56/485
56
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(11) Disconnect the Harness .(12) Loosen the Process Unit Screw (743).(13) Slide the Process Unit out.Caution:
To prevent damage to the Process Unit, ensurethe Right Cover is still open before pulling theProcess Unit out.
Caution:Exercise caution not to scratch the surface of theOPC Drum (Green), and not to touch it with barehands.
Caution:The OPC Drum is sensitive to light. To preventoptical exposure problems, do not expose theOPC Drum to direct sunlight or bright light (even if it is a 1000-Lux fluorescent lamp).
(14) Remove 1 Screw (1Y).(15) Remove the Front Lock Plate Assembly (751)
(longer plastic tab).(16) Remove 1 Screw (1Y).(17) Remove the Rear Lock Plate Assembly (752)
(shorter plastic tab).
(18) Turn the OPC Drum Assembly in the directionof the arrow and remove.
Caution:Exercise caution not to scratch the surface of theOPC Drum (Green), and not to touch it with barehands.
7/27/2019 Panasonic Dp2310 Service Manual
57/485
57
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(19) Remove the Harness from clamp, disconnectthe Connector .
(20) Remove 2 Screws (51) and 1 Snap Ring (G6).(21) Remove the Hopper Unit .
Note:When reinstalling the Hopper Unit, insert thehooks into the recessed holes on the Developer Unit as illustrated.
(22) Release 3 Latch Hooks and remove theDeveloper Cover (825).
(23) Stand the Developer Unit as illustrated over asuitable container and dump the used Developer and Toner by rotating the Gear.
(24) Clean the Developer Unit with a dry soft cloth.(25) Reinstall the Hopper Unit .
7/27/2019 Panasonic Dp2310 Service Manual
58/485
58
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(26) Shake the Developer Bottle thoroughly (approx.30 seconds).
(27) Pour the appropriate developer evenly into thedeveloper unit. Make sure to empty the bottle.
(28) Close the Developer Cover .
Note:When reinstalling the Developer Cover, ensurethat 2 Magnet Roller Sheets are outside asillustrated.
(29) Remove the OPC Drum Shaft Holder Assembly.
(30) Lift the OPC Drum , holding the right side wherethe OPC Drum Shaft Holder Assembly was
installed.Note:
Do not touch the surface of the OPC Drum withbare hands when removing or reinstalling it.Grease from fingerprints will affect copy quality.When installing a new OPC Drum, clean the BiasCharge Roller with a soft dry cloth.
(31) Remove the Bias Charge Roller (725).(32) Remove 2 Screws (20).
7/27/2019 Panasonic Dp2310 Service Manual
59/485
59
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(33) Remove the Cleaning Roller (706).
(34) Remove 2 Bias Charge Roller Holder (728) Assemblies.
Note:When reinstalling the Bias Charge Roller Holder
Assembly on the rear side, install the Bias ChargeRoller Holder (728) first and then the Bias ChargeRoller Bushing (726) with the Bushing Coil Spring(727) as illustrated.
(35) Remove 2 Screws (23).(36) Remove the Cleaning Blade (704).(37) Remove the Scoop Sheet (710).
7/27/2019 Panasonic Dp2310 Service Manual
60/485
60
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.2.5. Fuser Unit
CAUTION:To prevent from getting burned, do not install, remove, clean or make adjustments when the Fuser Unit ishot.
(1) Open the Right Cover (1201).(2) Remove 1 Screw (6P).(3) Remove the Harness Cover (1525).(4) Unlock the Angled Rear Arm (1218) and
the Front Arm (1217).
(5) Remove 1 Screw (6P).
(6) Remove the Support Plate (476).
(7) Remove 1 Screw (6P).(8) Remove the Strap Cover (1022).
(9) Disconnect the 3 Harnesses on the Terminals of Fuser Unit.Note:
When reinstalling, make sure that the 3 Harnessesare connected correctly as illustrated.
7/27/2019 Panasonic Dp2310 Service Manual
61/485
61
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(10) Disconnect 2 Harnesses .(11) Remove 4 Screws (4N).(12) Remove the Fuser Unit .
(13) Remove 4 Screws (6P).(14) Remove the Dual-Path Exit Guide .
(15) Clean the Feed Roller (1510) with a soft cloth,saturated with isopropyl alcohol.
(16) Clean the Feed Roller (1510) with a soft cloth,saturated with isopropyl alcohol.
7/27/2019 Panasonic Dp2310 Service Manual
62/485
62
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(17) Remove 3 Screws (4N).(18) Remove the Lower Fuser Cover (1003).
(19) Remove 2 Screws (21).(20) Disconnect the Harness .(21) Remove the Cleaning Web Roller Unit .
(22) Remove 1 Screw (21).(23) Remove the Rear Web Bracket (1071).(24) Remove the Cleaning Web Roller (1083) and
Web Pressure Roller (1080).
(25) Remove 2 Screws (36).(26) Remove the Thermostat (1038).(27) Remove 2 Screws (36).(28) Remove the Thermal Fuse (1040).(29) Remove 2 Screws (1Y).
(30) Remove the Thermistor Assembly (1041).
7/27/2019 Panasonic Dp2310 Service Manual
63/485
63
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(31) Remove 3 Screws (23).(32) Remove 2 Screws (19).(33) Remove the Harness Guide (1004).
(34) Remove 1 Screw (21).(35) Remove the Rear Lamp Holder (1021).
(36) Remove 2 Screws (16).
(37) Remove 1 Screw (21).(38) Remove the Front Lamp Holder (1018).
7/27/2019 Panasonic Dp2310 Service Manual
64/485
64
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(39) Remove 2 Fuser Lamps (1043 and 1044).Note:
Make sure to check the wattage of each Fuser Lamp when replacing.
Note:1. When reinstalling, route the Harnesses along the
hooks as illustrated.2. Be sure to install the longer Harness to the Gear
side and the shorter Harness to the other side.
3. Make sure that the 600W Fuser Lamp (WhiteHarness) is plugged into the upper left slot andthe 450W Fuser Lamp (Red Harness) is pluggedinto the lower right slot.
4. Route the Harnesses (White, Black and Red)along the 3 hooks as illustrated.
5. Do not touch the glass portion of the Fuser Lampwith bare hands. Grease from the fingerprints willshorten its life cycle, use a soft cloth, saturatedwith isopropyl alcohol to clean fingerprints.
6. Use care when handling the Fuser Lamps toavoid breakage.
(40) Remove 2 Screws (21).(41) Remove the Front and Rear Roller Holders
(1056 and 1057).
7/27/2019 Panasonic Dp2310 Service Manual
65/485
65
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(42) Remove the Fuser Roller (1026) Assembly.
(43) Remove the 2 C-Rings (1078).(44) Remove the E40 Heat Roller Gear (1014).(45) Remove the Plate Spacer (1023).(46) Remove the 2 Insulation Bushings (1006).(47) Remove the 2 Bearings (1046).Note:
1. The Plate Spacer is installed only to the non-Gear side.
2. Do not scratch the surface of the Fuser Roller when removing or reinstalling it.
Clean the Insulation Bushings with a soft cloth,saturated with isopropyl alcohol.
Clean the surface of the Fuser Roller with a softcloth, saturated with isopropyl alcohol.
(48) Disconnect the Harness .(49) Remove 2 Screws (23).(50) Remove the Upper Fuser Cover (1002).
7/27/2019 Panasonic Dp2310 Service Manual
66/485
66
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(51) Remove the Exit Roller (1028).
(52) Remove the Turn Guide (1007).(53) Remove 1 Screw (19).(54) Remove the Upper Guide (1001).
(55) Remove 5 Upper Fingers (1067).
(56) Remove the Pressure Roller (1027).
7/27/2019 Panasonic Dp2310 Service Manual
67/485
67
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(57) Remove 2 Bearings (1039).Note:
1. When reinstalling, make sure to install withBearing's Retainer Ring facing towards theRoller.
2. Do not scratch the surface of the PressureRoller when removing or reinstalling it.
Clean the surface of the Pressure Roller with a softcloth, saturated with isopropyl alcohol.
7/27/2019 Panasonic Dp2310 Service Manual
68/485
68
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.2.6. Drive Unit
(1) Remove 4 Silver Screws (S6).(2) Open the Rear Cover (302).
(3) Remove 4 Silver Screws (S6).(4) Remove the Rear Right Cover (507) and the
Right Rear Cover (518).
(5) Remove 2 Silver Screws (B1).(6) Remove the Lower Rear Cover (506).(7) Remove 1 Screw (24).(8) Remove 5 Fly Wheels (922).
(9) Remove the Process Unit . (Refer to 2.2.4. )(10) Remove 3 Screws (21).(11) Remove the HVPS Unit .
7/27/2019 Panasonic Dp2310 Service Manual
69/485
69
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(12) Disconnect the MT Harness (1926) on the MainMotor (CN1 and CN2).
(13) Remove 5 Screws (4N).(14) Remove the Main Motor (907).
(15) Disconnect the Connector on each of the 3Clutches.
(16) Remove 3 Snap Rings (S9).(17) Remove 3 Clutches (969, 1105 x 2).(18) Release The Harnesses from 4 Harness
Clamps.
(19) Remove 4 Screws (6P).(20) Remove the RD Cover (411).
(21) Remove 1 Screw (6P) and 2 Screws (19).(22) Remove the 1st Tray Drive Bracket (939).
7/27/2019 Panasonic Dp2310 Service Manual
70/485
70
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(23) Remove 3 Screws (19).(24) Remove the Motor Bracket (908).
7/27/2019 Panasonic Dp2310 Service Manual
71/485
7/27/2019 Panasonic Dp2310 Service Manual
72/485
72
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
(11) Remove 1 Screw (19).(12) Remove the Registration Pinch Roller (1222).
Clean the surface of the Registration Pinch Roller with a soft cloth, saturated with isopropyl alcohol.
(13) Remove the Roller Cleaner (1229).
Note:When installing the Roller Cleaner, make sure thatturn a felt of black side upwards as illustrated.
(14) Remove 3 Screws (C8).(15) Remove the BTR Guide (1223).
7/27/2019 Panasonic Dp2310 Service Manual
73/485
73
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(16) Remove the BTR Gear (1234).(17) Remove the Bias Transfer Roller (1221).
Clean the surface of the Bias Transfer Roller onlywith a soft dry cloth.
7/27/2019 Panasonic Dp2310 Service Manual
74/485
74
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.2.8. Sheet Bypass
(1) Remove 1 Screw (19).(2) Remove 1 Screw (1Y).(3) Remove the Snap Ring (S9).(4) Remove the P6L5 Conductive Bushing (972).(5) Remove the Dual-Path Guide (1203).
(6) Remove 1 Screw (19).(7) Remove the Feed Roller (1244).
Clean the surface of the Feed Roller with a softcloth, saturated with isopropyl alcohol.
(8) Remove the Separator Pad (1242).
Clean the rubber surface of the Separator Holder pad with a soft cloth, saturated with isopropylalcohol.
(9) Remove the Pressure Plate (1295).
7/27/2019 Panasonic Dp2310 Service Manual
75/485
75
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(10) Remove 1 Screw (X6).(11) Remove the Reverse Roller Guide (1294).
(12) Remove the Reverse Roller (1291) Assembly.
(13) Remove the Bushing (1286).(14) Remove the Washer (1288).
(15) Remove the E-Ring (J7).(16) Remove the Reverse Roller (1291).
Clean the surface of the Separation Roller with asoft cloth, saturated with isopropyl alcohol.
7/27/2019 Panasonic Dp2310 Service Manual
76/485
76
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.2.9. Paper Feed Module
(1) Remove the Process Unit . (Refer to 2.2.4. )(2) Remove the Clutch (1105). (Refer to 2.2.6. )(3) Remove the Snap Ring (S9).(4) Remove the Registration Roller (1121).
Clean the surface of the Registration Roller with asoft cloth, saturated with isopropyl alcohol.
(5) Remove 2 Screws (19).(6) Remove the Process Unit Guide (1104).
(7) Slide the 1st Paper Tray out.(8) Remove the Paper Feed Roller (1144).
Clean the surface of the Paper Feed Roller with asoft cloth, saturated with isopropyl alcohol.
(9) Remove the Reverse Clutch (1132).(10) Remove the C25 Gear Roller (1145).
Clean the surface of the C25 Gear Roller with asoft cloth, saturated with isopropyl alcohol.
7/27/2019 Panasonic Dp2310 Service Manual
77/485
7/27/2019 Panasonic Dp2310 Service Manual
78/485
7/27/2019 Panasonic Dp2310 Service Manual
79/485
79
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
2.2.11. Paper Transport Unit
(1) Remove the Inner Tray (1522).
(2) Push open the Paper Transport Jam Cover (1302).
(3) Clean 6 Pinch Rollers (1518) with a soft cloth,saturated with isopropyl alcohol.
7/27/2019 Panasonic Dp2310 Service Manual
80/485
80
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.2.12. PC Board
(1) Remove 7 Screws (6P).(2) Disconnect all the Harnesses on the SC PC
Board.(3) Remove the SC PC Board (1901).
(4) Remove 3 Screws (6P).(5) Disconnect all the Harnesses on the SPC PC
Board.(6) Remove the SPC PC Board (1902).
(7) Remove 2 Shoulder Silver Screws (L8: Upper)and 2 Silver Screws (S6: Lower).
(8) Remove 2 Screws (6P).(9) Open the LVPS Cover (301).
7/27/2019 Panasonic Dp2310 Service Manual
81/485
81
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
(10) Remove 6 Screws (6P).(11) Disconnect all the Harnesses on the ACD PC
Board.(12) Remove the ACD PC Board (1904).
(13) Remove 2 Screws (6P).(14) Disconnect all the Harnesses on the DC PC
Board.(15) Remove the DC PC Board (1905).
(16) Remove 9 Screws (6P).(17) Remove all the Harnesses on the LVPS(18) Remove the LVPS (1910).
7/27/2019 Panasonic Dp2310 Service Manual
82/485
82
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
2.3. Screw Identification Template* For DP-2330/3030
Part No. Figure RemarkRef. No.
DZPA000094
DZPA000088743
Shoulder ScrewDZPA0000251033
WasherXWG55E12FY1052
XTB3+8J19
XTB3+8JFJ
XYN3+F823
XYN3+F8FJ
XTB3+6F21
XTB3+6FFJ
XTB3+8F20
XTB3+8FFJ
XYN3+J618
XYN4+F824
XYN3+F636 XYN3+F6FJ
XTB3+10F51
XTB3+6J62
XTB3+10J1Y
XYN3+J816
Washer
XWG364
XYN3+J6FJ
XYN4+F8FJ
XTB3+10FFJ
XTB3+6JFJ
XTB3+10JFJ
XYN3+J8FJ
XWG3FJ
Screw
Screw *
Screw
Screw *
Screw
Screw *
Screw
Screw *
Screw
Screw *
Screw
Screw *
Screw
Screw *
ScrewScrew *
Screw
Screw *
Screw
Screw *
Screw
Screw *
Screw
Screw *
Washer *
7/27/2019 Panasonic Dp2310 Service Manual
83/485
83
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
Part No. Figure RemarkRef. No.
ScrewDZPB000020C2
Silver ScrewDZPB000007B1
XTW3+10SE8
XTW3+8SFCC8
XTW3+8SFJ
XTW3+6LFC
6PXTW3+6LFJ
XTB26+6J7B
XTB26+6JFJ
XSN3+W8FC4N
XTW3+10SFJ
XSN3+W8FJ
Screw
Screw
Screw
Screw
Screw
XTB3+32JE5
XTB3+24JE6
Blue Screw (For DP-2310/3010 only)
Red Screw (For DP-2310/3010 only)
DZPA000014D25
Bule Screw
Red Screw
DZPA000013D24
Black Screw
Black Screw (For DP-2310/3010 only)XTB3+8JFKB4
E-Ring
XUC65Z
XYN3+F45M
E-Ring
XUC45Y
XTB3+32JFJ
XTB3+24JFJ
XTB3+8JFJ-B
XTB3+8JFJ-R
XTB3+8JFI
XUC6FJ
XYN3+F4FJ
XUC4FJ
Screw
Screw
Screw
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
E-Ring (For DP-2310/3010 only)
E-Ring (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
7/27/2019 Panasonic Dp2310 Service Manual
84/485
84
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
Part No. Figure RemarkRef. No.
ScrewXTN3+10GF9
Silver ScrewXSN4+W10FNF7
ScrewDZPA000063F4
WasherDZPK000021F6
Snap RingFFPFJ0039BG6
E-RingXUC3VMJ6
E-RingXUC4VMJ7
E-RingXUC7VMJ8
Snap RingFFPFJ0033BH6
Snap RingFFPFJ0041BH7
XTB3+8GF10
XTB3+8GFJ Screw
E-RingXUC2VML7
Shoulder ScrewDZPB000031L8
XTB3+4FL9
XTB3+4FFJ Screw
XTB26+8JH4 XTB26+8JFJ
Screw
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
7/27/2019 Panasonic Dp2310 Service Manual
85/485
85
DP-2330/3030
MAR 2005Ver. 2.1
DP-2310/3010
Part No. Figure RemarkRef. No.
ScrewDZPA000086S6
ScrewFFPFA0152P7
ScrewXTN3+8GP5
Snap RingDZJM000171S9
Silver ScrewXTW3+10LFNV4
ScrewDZPA000087T2
Screw
XTB3+12JP2
XTB3+12JFJ
Tumb ScrewDZPA000064M2
Screw
B3x6TTS-RPP1
XTB3+6FFJ-RP
Red Screw
XTB3+12FS8
XTB4+10FN3
XYN3+F5FYT4
XTN3+6FR-CT5
XTB3+12FFJ
XTB4+10FFJ
XYN3+F5FJ
XTN3+6FFJR
Screw
Screw
Screw
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Red Screw (For DP-2310/3010 only)
7/27/2019 Panasonic Dp2310 Service Manual
86/485
7/27/2019 Panasonic Dp2310 Service Manual
87/485
7/27/2019 Panasonic Dp2310 Service Manual
88/485
88
DP-2330/3030
MAR 2005Ver.2.1
DP-2310/3010
3.2. Required Tools
3.2.1. Preventive Maintenance Method
No. Tools No. Tools1 Soft Cloth 7 Pliers2 Isopropyl Alcohol 8 Cotton Swab3 Phillips Screwdriver (#2) 9 Brush
4 Stubby Phillips Screwdriver (#2) 10KS-660 - Conductive Grease(Available from Shin-Etsu Silicones of America, Inc.URL: http://www.shinetsusilicones.com )
5 Slotted Screwdriver (3/32 in) 11Molykote EM-50L Grease(Available from Dow Corning,URL: http://www.dowcorning.com )
6 Tweezer
No. Part Description ImportantAction Comments
1 Memory Data Check 1. Print the RAM DATA for reference and as a pre-caution.2. After completing the task(s), print and compare the RAM
DATA with the previously printed one.2 Auto Docume