Embed Size (px)
Citation preview
www.zyxel.com
802.11n Wireless VDSL2 4-port Gateway
Firmware Version 1.10Edition 1, 5/2011
P-873HNUP-51B
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
User Name: admin
Password: 1234
Copyright 2011ZyXEL Communications Corporation
2
Device Panels
POWER
ETHERNET 1-4
USB
WLAN/WPS
ETHERNET WAN
INTERNET
DSL 1
HPNA
POWER
ETHERNET 1-4
USB
ETHERNET WAN
HPNA
RESET
DSL 2
DSL 1
DSL 2
P-873HNUP-51B
3
Requirements
Make sure you have the following things before you start:
• INTERNET ACCESS: You need an Internet account with an ISP (Internet Service Provider) and information such as your user name, password, and so on.
• WEB BROWSER: Internet Explorer 6.0 and later versions, with JavaScript enabled, or Mozilla Firefox 3 and later versions, or Safari 2.0 and later versions. The browser will be used to access the Internet and/or access the P-873HNUP-51B’s Web Configurator.
Hardware Setup
Place the P-873HNUP-51B flat on a desk or table or on the stand for a vertical installation.
Remove the P-873HNUP-51B’s clear plastic covers before using it.
To connect the stand, line up the arrow on the stand with the arrow on the bottom of the device as shown.
4
To connect your P-873HNUP-51B:
3
2
45
6
1
P-873HNUP-51B
5
1. Attach the antenna and point it up.
2. Do one of the following for your Internet connection:
a. DSL 1,2: Use a telephone cable to connect your P-873HNUP-51B’s DSL1 port to a telephone jack (or the DSL or modem jack on a splitter if you have one).
b. If the DSLAM at your ISP supports DSL bonding function, you can connect DSL1 and DSL2 to two seperate telephone jacks. This provides increased throughput at longer distances. You will need to access the Web Configurator and enable the DSL Bonding function in the Broadband > DSL screen. See the User’s Guide for more information.
c. ETHERNET WAN: If you already have a broadband router or modem, use an Ethernet cable to connect the ETHERNET WAN port to it for Internet access.
3. ETHERNET: Use an Ethernet cable to connect a computer to an Ethernet port for initial configuration and/or Internet access.
4. HPNA: Use a coaxial cable to connect to a coaxial outlet and relay Internet traffic throughout your house through coaxial cabling.
5. USB: Connect a USB (version 2.0 or lower) memory stick or a USB hard drive for file sharing. Use a USB extension cable if the stick is too big to fit.
6. POWER: Use the provided power adaptor to connect the POWER socket to an appropriate power source. Make sure the power at the outlet is on. After connecting the power adaptor, look at the lights on the front panel.
• The POWER light blinks while your P-873HNUP-51B starts up and then stays on once it is ready.
• Each LAN light stays on if the corresponding Ethernet port is properly connected and blinks when there is traffic.
• The ETHERNET WAN light stays on if the ETHERNET WAN port is properly connected and blinks when there is traffic.
6
• The USB light turns on when your P-873HNUP-51B detects a connected USB device.
• The HPNA light stays on if the HPNA port is properly connected and blinks when there is traffic.
• The DSL1,2 lights are green when your P-873HNUP-51B has an ADSL connection. They are orange when you have a VDSL connection. If you are not using DSL bonding function, only DSL1 light will be on.
• The WLAN / WPS light flashes green when WLAN is activated and orange while WPS is in process. It stays on green when the wireless LAN is ready and blinks when there is traffic.
• The INTERNET light turns on when the gateway is able to access the Internet and will blink when your P-873HNUP-51B is sending or receiving data.
If the lights do not come on, check your connections and inspect your cables for damage. If the lights are still off, contact technical support.
Set Up a Wireless Network
You can set up a wireless network using the following methods:
Using Wireless Protected Setup (WPS)Press the WPS button on the P-873HNUP-51B’s front panel for more than 5 seconds to turn the WPS function on.
P-873HNUP-51B
7
Follow these steps to add a WPS-enabled device to the wireless network using the WPS/WLAN button.
Set Up a Wireless Network ManuallyThe wireless LAN on your P-873HNUP-51B is enabled by default. To add a wireless client to the network, use the settings found on the side panel of your P-873HNUP-51B, which will look similar to the following example:
Configure wireless devices that you want to connect to the wireless network to use the same wireless settings as the P-873HNUP-51B.
The default wireless settings vary for each P-873HNUP-51B. Refer to the side panel of your device and use the provided information.
Place the devices you want to connect near one another.
Press the WPS button on the P-873HNUP-51B.
The WPS light blinks green and orange.
Press the WPS button on a compatible device within 2 minutes of pressing the button on the P-873HNUP-51B.
The WPS light on the P-873HNUP-51B shines steadily when connected.
1
12
3
SSID: ZyXEL00561Security Mode: WPA-PSKPre-Shared Key: FB373BD356
8
The Web Configurator
The Web Configurator is a web browser tool that allows you to configure the P-873HNUP-51B. The computer and the P-873HNUP-51B need to be in the same IP address range to use this tool.
1. Open your browser and enter http://192.168.1.1 (the P-873HNUP-51B’s default IP address) as the address.
2. Enter the default user name admin and password 1234. Click Login.
If the login screen does not open, make sure you allow web browser pop-up windows, JavaScript and Java permissions. Your computer should be also set to get an IP address automatically from a DHCP server. See the appendices in your User’s Guide for more information.
P-873HNUP-51B
9
3. A welcome screen appears with details about your last login. Select Show this page next time to see the welcome screen on your next login. Otherwise, clear it. Click Continue.
4. The Network Map page appears. This shows whether the P-873HNUP-51B and computers/devices connected to it have Internet access.
10
5. Click Status to display the following screen, where you can view the P-873HNUP-51B’s device, interface, and system information.
P-873HNUP-51B
11
6. Click Quick Start and configure the P-873HNUP-51B’s time zone Internet access, and wireless settings.
See your User’s Guide for how to use the rest of the Web Configurator screens. You will need to refer to the section on how to setup the Broadband connection if the INTERNET LED (light) remains off.
For more information, please refer to the User’s Guide on the provided CD or at the www.zyxel.com download library.
Was this guide helpful? Send your comments to [email protected]
Procedure to View a Product’s Certification(s)
1. Go to www.zyxel.com.
2. Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.
3. Select the certification you wish to view from this page.
12
ENG
LISHD
EUTSC
HESPA
ÑO
LFR
AN
ÇA
IS
Green Product D
eclaration
RoH
S D
irective 2002/95/EC
WEEE D
irective 2002/96/EC
(WEEE: W
aste Electrical and Electronic Equipm
ent) 2008/34/EC
Declaration Signature:
Nam
e/Title: R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Date (yyyy/m
m/dd): 2011/1/24
Green Product D
eclaration
RoH
S Directive 2002/95/EC
WEEE D
irective 2002/96/EC
(WEEE: W
aste Electrical and Electronic Equipm
ent) 2008/34/EC
Unterschrift des Erklärenden:
Nam
e/Titel: R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Datum
(JJJJ/MM
/TT): 2011/1/24
Declaración de Producto Ecológico
Directiva R
oHS 2002/95/EC
Directiva R
EEE 2002/96/EC
(REEE : R
esiduos de Equipos Eléctricos y Electrónicos) 2008/34/EC
Firma de declaración:
Nom
bre/Título: R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Fecha (aaaa/mm
/dd): 2011/1/24
Déclaration de Produit G
reen
Directive R
oHS 2002/95/EC
Directive D
EEE 2002/96/EC
(DEEE : D
échets des Equipements
Electriques et Electroniques) 2008/34/EC
Signature de la déclaration :
Nom
/Titre : R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Date (aaaa/m
m/jj) : 2011/1/24
ITALIA
NO
NED
ERLAN
DS
SVENSK
A
Dichiarazione G
reen Product
Direttiva R
oHS 2002/95/C
E
Direttiva R
AEE 2002/96/CE
(RAEE: R
ifiuti di Apparecchiature Elettriche ed Elettroniche) 2008/34/EC
Firma dichiarazione:
Nom
e/titolo: R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Data (aaaa/m
m/gg): 2011/1/24
Productmilieuverklaring
RoH
S-richtlijn 2002/95/EC
AEEA-richtlijn 2002/96/EC
(AEEA: Afgedankte Elektrische en Elektronische Apparaten) 2008/34/EC
Verklaringshandtekening:
Naam
/titel: R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Datum
(jjjj/mm
/dd): 2011/1/24
Miljödeklaration
RoH
S Direktiv 2002/95/EC
WEEE D
irektiv 2002/96/EC
(WEEE: hantering av elektriskt och
elektroniskt avfall) 2008/34/EC
Deklaration undertecknad av:
Nam
n/Titel: R
aymond H
uang/ Q
uality & Custom
er Service Division Assistant VP
Datum
(åååå/mm
/dd): 2011/1/24
