OXM300002 DBS3900 WiMAX Data Configuration ISSUE1.00.ppt

www.huawei.com

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

英文标题 :40-47pt

副标题 :26-30pt

字体颜色 : 反白内部使用字体 :

FrutigerNext LT Medium

外部使用字体 : Arial

中文标题 :35-47pt

字体 : 黑体副标题 :24-28pt

字体颜色 : 反白字体 : 细黑体

DBS3900 WiMAX Data Configuration

Page3Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

References

DBS3900 WiMAX Commissioning Guide


Objectives

Upon completion of this course, you will be able to: Finish basic data configuration for WiMAX DBS3900


Contents

1. Preparing for the Data

2. Setting Up the OM Links

3. Configuring BTS Data


Contents





WiMAX Network Architecture


OM Link Data

Item Description

IP address of the local maintenance port

The IP address of the maintenance port on CMPT board. Default value: 192.168.0.100

ITFIP The IP address of the physical port corresponding to the OM link. Physically, it is the IP address of the traffic port on the BMPT.

OM IPA logical IP address and is deployed on the BMPT. It is used for the connection between the BTS and the M2000.

M2000 IP The IP address of the M2000 server.

Route The route from the BTS to the M2000.


Data Associated with R6 Interface

Item Description

ITFIPThe IP address of the physical port corresponding to the R6 interface. Physically, it is the IP address of the traffic port on the BMPT.

Signaling IP address A logical IP address, which is deployed on the BMPT. It is used for signaling exchange.

IPPATH The path between the ITFIP and the GWIP.

GWIP The IP address of the ASN-GW, which communicates with the BTS. It’s a logical R6 interface IP address in WASN9770

Route The route from the BTS to the GW.

GWID It is the ID of the ASN-GW, which communicates with the BTS. For example, 0505-0505-0505.


Data Associated with R1 Interface

Item Description

Operator ID The operator ID

Site IDA part of BSID. You can change BSID by changing Site ID.

Configured frequency It is the center frequency of carrier

Bandwidth It is the channel bandwidth of carrier

Sub-frame ratioIt is the ratio of the TDD frame of the downlink to that of the uplink


Zone Information (10M/7M)Configuration Description

SECTORID

DLSEGMENT NO

DLBITMAP ULBITMAPDLZONEIND

ULZONEIND

10M/7M PUSC1/3

0 0 00000003000000000000000FFF 1 1

1 1 0000000C000000000000FFF000 1 1

2 2 000000300000000007FF000000 1 1

10M/7M PUSCALL

0 0 0000003F0000000007FFFFFFFF

8 4

1 1 0000003F0000000007FFFFFFFF

8 4

2 2 0000003F0000000007FFFFFFFF

8 4


Zone Information (5M)

Configuration Description

SECTOR ID

DLSEGMENT NO

DLBITMAP ULBITMAPDLZONEIND

ULZONEIND

5M PUSCALL

0 0 0000001500000000000001FFFF 8 4

1 1 0000001500000000000001FFFF 8 4

2 2 0000001500000000000001FFFF 8 4


Optional Parameters

Serial Number Item

1 Paging group

2 Neighboring cell

3 SectorID

4 CarrierID

5 PreambleIndex

6 DLPUSCPERMBASE

7 DLPUSCALLPERMBASE


Optional Parameters (Cont.)

Serial Number Item

8 DLFUSCPERMBASE

9 DLBANDPERMBASE

10 DLPUSCSTCPERMBASE

11 DLPUSCALLSTCPERMBASE

12 ULPUSCPERMBASE

13 ULPUSCALLPERMBASE

14 ULBANDPERMBASE


BSID and GWID

OperatorID24bits

SiteID16bits

SectorID4bit

CarrierID4bits

OperatorID24bits

CountryID8bits

CityID6bits

SiteID4bits

GW Num6bits

BSID

GWID


Contents





Setting Up the OM Links Locally Run the SET DHCPFUNC command to disable the

DHCP.

Example: SET DHCPFUNC: STRFLG=DISABLE;


Setting Up the OM Links Locally (Cont.) Configure the ITFIP (service interface IP)

Run the RMV ITFIP command to remove the

configured ITFIP

Run the ADD ITFIP command to add the ITFIP

Run the LST ITFIP command to query the ITFIP


Setting Up the OM Links Locally (Cont.) Add IPRT (route)

If the configured route is incorrect, run the RMV IPRT

command to remove the configured route

Run the ADD IPRT command to add IPRT

Run the LST IPRT command to query the IPRT


Setting Up the OM Links Locally (Cont.) Configure the OMCH

Run the MOD OMCH command to modify the

configured OMCH

Run the ADD OMCH command to add an IP

Run the LST OMCH command to query the OMCH

Run the PING command to check whether the OM

links are successfully configured


Contents





Configuring the Equipment Data Run the LST SUBRACK command to query the configurati

ons of the BBU and RRU Run the ADD SUBRACK command to add RRU subracks

BBBI Slot ID CPRI Port IDRRU Subrack ID

RRU ID

1

0 2 0

1 3 1

2 4 2

3

0 5 3

1 6 4

2 7 5


Configuring the Equipment Data (Cont.) Run the LST BRD command to query the

configurations of the board in the BBU

Run the ADD BRD command to add the BMPT or

BBBI if necessary


Configuring the Equipment Data (Cont.) Run the LST RRU command to query the

configurations of the RRU

Run the ADD RRU command to add RRU boards.

Run the ADD SECTOR command to configure sectors

according to the data provided by the operator.

Run the ADD CARRIERBASICINFO command to

configure carriers according to the data provided by

the operator


Configuring Clock Sources and Time Sources Run the SET CLKSRC command to configure the

clock sources

Run the LST TIMESRC command to query the reference time sources of the BTS

Run the SET TIMESRC command to set the reference time sources

If you want to set the time manually, run the SET TIME command to set the time

If you want to use NTP server as time source, run the SET NTPC command to set the time


Configuring Clock Sources and Time Sources (Cont.) Set the time threshold

Run the LST TIMETHRD command to query the time synchronization threshold and the validity

Run the SET TIMETHRD command to set the time synchronization threshold and the validity

Set the time zone and daylight saving time (DST) Run the LST TZ command to query the time zone and

daylight saving time

Run the SET TZ command to set the time zone and daylight saving time

Run the LST TZ command to query the time zone and DST


Configuring R6 Interface Run the SET ETHPORT command to set the attribute of

an Ethernet port

Run the ADD ITFIP command to add the IP address of

an interface

Run the ADD SIGCH command to add a signaling

channel

Run the ADD IPPATH command to add an IP channel

Run the ADD IPRT command to add a route between

the BTS and the ASN-GW


Configuring R6 Interface (Cont.) Run the MOD MIXCFG command to configure the IP

address and ID of the gateway

Run the SET DIFPRI command to set priorities for

differential services. (optional configuration)

Run the PING command to check whether the R6

interface is enabled


Configuring R1 Interface

Run the SET RBSNAME command to set the BTS name

Setup operator ID and site ID, run the following command

Run the MOD CARRIERBLOCKFLAG command to block the

corresponding carrier

Run the RMV BTSINFO command to delete the operator ID

Run the ADD BTSINFO command to add the operator ID and

site ID

Run the LST BTSINFO command to query the operator ID

and site ID

Run the MOD CARRIERBLOCKFLAG command to unblock

the corresponding carrier


Configuring R1 Interface (Cont.) Run the MOD CARRIERBASICINFO command to

configure or modify the basic carrier information

Run the MOD CARRIERZONEINFO command to

modify the zone information table

Run the ADD NBR command to add neighboring

cells

Run the RMV NBR command to remove neighboring

cells


Adding BTS and BS in ASN-GW Log in to the LMT client of the ASN-GW

Configure the local BTS information

Run the LST BTS command to query the information of the local

BTS

Run the ADD BTS command to add the information of the local

BTS

Configure the information of the local BS

Run the LST LBS command to query the information of the local

BS

Run the ADD LBS command to bind BSID with new BTSIP


Summary


Glossary

BS : Base Station

OM : Operation and Maintenance

ITF: Interface

Thank youwww.huawei.com

Documents

OXM300002 DBS3900 WiMAX Data Configuration ISSUE1.00.ppt