Owner's Manual - Kenmore

Embed Size (px)

Citation preview

  • 8/3/2019 Owner's Manual - Kenmore

    1/25

    Side by Side RefrigeratorRefrigerador de dos puertasR_frig_rateur c6te & c6te% . ,

  • 8/3/2019 Owner's Manual - Kenmore

    2/25

    TABLE OF CONTENTSWARRANTY .................................................................................... 2REFRIGERATOR SAFETY ............................................................. 3REFRIGERATOR INSTALLATION ................................................. 4

    Unpacking .................................................................................... 4Location Requirements ................................................................ 4Electrical Requirements ............................................................... 5Base Grille .................................................................................... 5Door Removal ............................................................................... 6Door Closing and Alignment ........................................................ 8Water Supply Connection ............................................................ 8Water System Preparation ........................................................... 9Normal Sounds ............................................................................ 9

    REFRIGERATOR USE .................................................................... gEnsuring Proper Air Circulation .................................................... 9Using the Controls ..................................................................... 10Water and Ice Dispensers .......................................................... 11Water Filtration System .............................................................. 12Ice Maker and Storage Bin/Bucket ............................................ 13

    REFRIGERATOR FEATURES ...................................................... 14Refrigerator Shelves ................................................................... 14Flip-up Shelf ............................................................................... 14Adjustable Flip-up Shelf ............................................................. 14Dell Drawer ................................................................................. 15Convertible Vegetable/Meat Drawer, Crisper and Covers ... .. .. . 15Convertible Vegetable/Meat Drawer Temperature Control ....... 15Crisper Humidity Control ........................................................... 15Wine or Can/Bottle Rack ........................................................... 16Utility Bin .................................................................................... 16

    FREEZER FEATURES .................................................................. 16Freezer Shelf .............................................................................. 16Freezer Basket or Bin ................................................................. 16

    DOOR FEATURES ........................................................................ 16Door Rails ................................................................................... 16Can Racks and Door Bins .......................................................... 17

    REFRIGERATOR CARE ............................................................... 17Cleaning ...................................................................................... 17Changing the Light Bulbs ........................................................... 17Power Interruptions .................................................................... 18Vacation and Moving Care ........................................................ 18

    TROUBLESHOOTING .................................................................. 19SERVICE ........................................................................................ 22

    In the U.S.A ................................................................................ 22In Canada ................................................................................... 22Accessories ................................................................................ 22

    WATER FILTER CERTIFICATIONS ............................................. 23PRODUCT DATA SHEETS ........................................................... 24

    WARRANTYONE-YEAR FULL WARRANTY ON REFRIGERATORFor one year from the date of purchase, when this refrigerator isoperated and maintained according to instructions attached to orfurnished with the product, Sears wil l repair this refrigerator, freeof charge, if defective in material or workmanship.FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATIONSYSTEMFor five years from the date of purchase, when this refrigerator isoperated and maintained according to owner's instructionsattached to or furnished with the product, Sears will repair thesealed system (consist ing of refr igeration, connecting tubing, andcompressor), free of charge, if defective in materials orworkmanship.The above warranty coverage applies only to refrigerators whichare used for storage of food for private household purposes andexcludes original and replacement Kenmore Fil tered Ice & Waterfilter cartridges (if equipped with the filter system). Original andreplacement cartridges are warranted for 30 days, parts only,against defects in material or workmanship.WARRANTY SERVICE IS AVAILABLE BY CONTACTING THENEAREST SEARS SERVICE CENTER IN THE UNITED STATESOR CANADA.This warranty applies only while this product is in use in theUnited States or Canada. This warranty gives you specificlegal rights, and you may also have other rights which varyfrom state to state or province to province.Warranty terms may vary in Canada. Contact your local SearsService Center for complete details.

    Sears, Roebuck and Co.Dept. 817WA, Hoffman Estates, IL 60179

    Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8Product RecordIn the space below, record your complete model number, serialnumber, and purchase date. You can find this information on themodel and serial number label located on the inside wall of therefrigerator compartment.Have this information available to help you obtain assistance orservice more quickly whenever you contact Sears concerningyour refrigerator.Model number 106.Serial numberPurchase dateSave these instructions and your sales receipt for futurereference.

    2

  • 8/3/2019 Owner's Manual - Kenmore

    3/25

    REFRIGERATOR SAFETYYour safety and the safety of others are very important.

    We have provided many important safety messages in this manual and on your appliance. Always read and obey allsafety messages.

    This is the safety alert symbol.This symbol alerts you to potential hazards that can kill or hurt you and others.All safety messages will follow the safety alert symbol and either the word "DANGER" or"WARNING." These words mean:You can be killed or seriously injured if you don'timmediately follow instructions.You can be killed or seriously injured if you don'tfollow instructions.

    All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell youwhat can happen if the instructions are not followed.

    IM PORTANT SAFETY INSTRUCTIONSWARN IN G:To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basicprecautions:n Plug into a grounded 3 prong outlet.n Do not remove ground prong.n Do not use an adapter.n Do not use an extension cord.n Disconnect power before servicing.n Replace all panels before operating.n Remove doors from your old refrigerator.

    Use nonflammable cleaner.n Keep flammable materials and vapors, such asgasoline, away from refrigerator.n Use two or more people to move and installrefrigerator.n Disconnect power before installing ice maker (onice maker kit ready models only).n Use a sturdy glass when dispensing ice or water(on some models).

    SAVE THESE INSTRUCTIONSProper Disposal ofYour Old Refrigerator

    Before you throw away your old refrigerator or freezer:n Take off the doors.n Leave the shelves in place so that children may not easilyclimb inside.

    IMPORTANT: Child entrapment and suffocation are not problemsof the past. Junked or abandoned refrigerators are stil l dangerous- even if they will sit for "just a few days." If you are getting rid ofyour old refrigerator, please follow these instructions to helpprevent accidents.

  • 8/3/2019 Owner's Manual - Kenmore

    4/25

    REFRIGERATORINSTALLATION

    Removing packaging materials Remove tape and glue residue from surfaces before turningon the refrigerator. Rub a small amount of liquid dish soapover the adhesive with your fingers. Wipe with warm waterand dry.

    Do not use sharp instruments, rubbing alcohol, flammablefluids, or abrasive cleaners to remove tape or glue. Theseproducts can damage the surface of your refrigerator. Formore information, see the "Refrigerator Safety" section.When Moving Your Refrigerator:Your refrigerator is heavy. When moving the refrigeratorfor cleaning or service, be sure to protect the floor.Always pull the refrigerator straight out when moving it.Do not wiggle or "walk" the refrigerator when trying to moveit, as floor damage could occur.

    Cleaning before useAfter you remove all of the packaging materials, clean the insideof your refrigerator before using it. See the cleaning instructionsinthe "Refrigerator Care" section.Important information to know about glass shelvesand covers:Do not clean glass shelves or covers with warm water whenthey are cold. Shelves and covers may break if exposed tosudden temperature changes or impact, such as bumping.For your protection, tempered glass is designed to shatterinto many smal l, pebble-size pieces. This is normal. Glassshelves and covers are heavy. Use special care when re-moving them to avoid impact from dropping.

    Explosion HazardKeep flammable materials and vapors, such asgasoline, away from refrigerator.Failure to do so can result in death, explosion,or fire.

    To ensure proper ventilation for your refrigerator, allow for _/2n.(1.25 cm) space on each side and at the top. When installing yourrefrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum oneach side (depending on your model) to allow for the door toswing open. If your refrigerator has an ice maker, allow extraspace at the back for the water line connections.NOTE: Do not install the refrigerator near an oven, radiator, orother heat source, nor in a location where the temperature will fallbelow 55F (13C).

    //

    //2" 1.25 cm (

    /

    ,m2" (5.08 cm) f

    4

  • 8/3/2019 Owner's Manual - Kenmore

    5/25

    ElectricalShockHazardPlugintoagrounded3 prongoutlet.Donot removegroundprong.Donot useanadapter.Donot usean extension cord.Failure to follow these instructions can result indeath, fire, or electrical shock.

    Before you move your refrigerator into its final location, it isimportant to make sure you have the proper electricalconnection:

    Recommended grounding methodA 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, groundedelectrical supply is required. It is recommended that a separatecircui t serving only your refrigerator be provided. Use an outletthat cannot be turned off by a switch. Do not use anextension cord.NOTE: Before performing any type of installation, cleaning, orremoving a light bulb, turn the control (Thermostat, Refrigeratoror Freezer Control depending on the model) to OFF and thendisconnect the refrigerator from the electrical source. When youare finished, reconnect the refrigerator to the electrical sourceand reset the control (Thermostat, Refrigerator or Freezer Controldepending on the model) to the desired setting.

    To remove the base grille:1. Open both refrigerator doors.2. Place hands along the ends of the grille, with your thumbsalong the top. Push in with your thumbs and pull up on thebottom.NOTE: Be sure to refasten the Tech Sheet behind the base grilleafter cleaning.To replace the base grille:1. Open the doors.2. Line up the grille support tabs with the metal clips,3, Push the grille firmly to snap it into place.

  • 8/3/2019 Owner's Manual - Kenmore

    6/25

    TOOLSNEEDED:/4n.,1/2n.,and%6n.hex-headocketwrenches,flat-headcrewdriverndaPhillipscrewdriver.IMPORTANT:eforeoubegin,urnherefrigeratorontrolOFF,nplugefrigeratorrdisconnectower.Removeoodandanyadjustableoororutilitybinsromdoors.

    Electrical Shock HazardDisconnect power before removing doors.Reconnect both ground wires before operating,Failure to do so can result in death or electrical shock.

    \

    Top Left Hinge

    1. Do Not Remove Screw

    Water DispenserTubing Connection

    11. Red Outer Ring

    Base Grille

    Door Removal

    Handle Removal(Optional)

    Top Right Hinge

    Do Not Remove Screw

    Bottom Hinge

    1. Do Not Remove Screw

    6

  • 8/3/2019 Owner's Manual - Kenmore

    7/25

    NOTE: It may only be necessary to remove either the door handleor the doors to get your product through the doorway of yourresidence. Measure the door opening to determine whether toremove the refrigerator handles or the doors.Handle Removal (optional)

    1. Apply firm pressure with your hand on the face of trim. Slidetop trim up and bottom trim down away from handle. Lift trimpieces off shoulder screws (see Graphic 1).2. Remove handle screws and handles.3. Move refrigerator into place. Replace handles as shown (seeGraphic 1).Door Removal

    Door and Hinge Replacement1. Replace both bottom hinges, if removed. Tighten screws.2. Assistance may be needed to feed the water line through thebottom hinge while reinstall ing the freezer door. Carefully feedthe dispenser tubing through the bottom left hinge beforereplacing the door on the hinge.NOTE: Provide additional support for the doors while the tophinges are being replaced. Do not depend on the door magnetsto hold the doors in place while you are working.3. Reconnect water dispenser tubing by pushing tubing intofitting until it stops and black mark touches face of fitting (seeGraphic 3). On some models, replace tubing in hose clip.4. Align and replace the top left hinge as shown (see Graphic 4).Tighten screws.

    Electrical Shock HazardDisconnect power before removing doors.Failure to do so can result in death orelectrical shock.

    1. Unplug refrigerator or disconnect power.2. Open both refrigerator doors. Remove the base grille bypulling up on the bottom outside corners (see Graphic 2).3. Close both doors and keep them closed until you are ready toli ft them free from the cabinet.4. If you have a dispenser (ice or water), disconnect the waterdispenser tubing located behind the base grille on the freezerdoor side (see Graphic 3).

    Press red outer ring against the face of fitting and pull thedispenser tubing free. On some models, remove tubing from hose clip.

    5. Remove top left hinge screw and cover as shown (seeGraphic 4).

    6. Disconnect wiring plug and both ground wires from groundwire screw (on some models) as shown (see Graphic 4).

    7. Remove remaining left hinge screws and hinge as shown (seeGraphic 4). Do not remove screw 1.8. Carefully lift freezer door straight up off bottom hinge (seeGraphic 5). The water dispenser tubing remains attached to

    the freezer door and pulls through the bottom le_ hinge.Make sure you protect the dispenser tubing from damage.9. Remove top right hinge cover and screws as shown (seeGraphic 6). Do not remove screw 1.10. Lift the refrigerator door straight up off bottom hinge.11. It may not be necessary to remove the bottom hinge to movethe refrigerator through a doorway. Both bottom hinges havesimilar construction.

    Disassemble the hinges as shown (see Graphic 7). Do notremove screw 1.

    Electrical Shock HazardReconnect both ground wires.Failure to do so can result in death orelectrical shock.

    Style 1 Reconnect both ground wires. Reconnect wiring plug.

    Style 1Style 2

    Reconnect wiring plug.5. Replace left hinge cover and screws.6. Replace the refrigerator door by carefully lifting the door ontothe bottom right hinge.7. Align and replace the top right hinge as shown (seeGraphic 6). Tighten screws.8. Replace hinge cover and screws. Tighten screws.9. Plug into a grounded 3 prong outlet.

  • 8/3/2019 Owner's Manual - Kenmore

    8/25

    3,

    Door Closing1. Move the refrigerator into its final position.2. Place a level inside the refrigerator at the back of the top shelf(see Graphic 6).3. Locate the leveling screws behind the base grille of therefrigerator on either side.4. Use a hex-head socket wrench to adjust the rear rollerleveling screws unti l the refrigerator is level. Turn the rearroller leveling screw to the right to raise that side of therefrigerator or turn the leveling screw to the left to lower thatside (see Graphic 9). Make sure refrigerator is level beforeproceeding.5. Check the door alignment after leveling the refrigerator.Door Alignment

    If the doors are uneven after leveling the product (seeGraphic 10), follow the steps below.1. Use a hex-head socket wrench to adjust the front rollerleveling screws until the doors are even. Turn the front roller

    leveling screw to the right to raise that side of the refrigeratoror turn the leveling screw to the left to lower that side (seeGraphic 11).NOTE: Open and close both the refrigerator and freezer doorsafter each adjustment to check the door alignment.2. Open the doors and replace the base grille. Line up the grillesupport tabs with the metal clips. Push the grille firmly tosnap it into place.NOTE: Be sure to refasten the Tech Sheet behind the base grille.

    Read all d irections carefully before you begin,IMPORTANT: If you turn the refrigerator on before the water line isconnected, turn the ice maker OFE All installations must meet local plumbing code requirements. Use copper tubing and check for leaks. Install copper tubingonly in areas where temperatures wil l remain above freezing.Tools required: Standard screwdriver, 7/_en. and _/2n. open-endwrenches or two adjustable wrenches, V4in. nut driver and drillbit, hand drill or electric drill (properly grounded).NOTE: Your refrigerator dealer has a kit available with a V4in.(6.36 mm) saddle-type shutoff valve, a union, and copper tubing.Before purchasing, make sure a saddle-type valve complies withyour local plumbing codes. Do not use a piercing-type or 3/_6n.(4.76 mm) saddle valve which reduces water flow and clogs moreeasily.Cold water supplyConnect the ice maker to a cold water line with water pressurebetween 30 and 120 psi. If you have questions about your waterpressure, call your uti li ty company.Connecting to Water Line

    1. Unplug refrigerator or disconnect power.2. Turn OFF main water supply. Turn ON nearest faucet longenough to clear line of water.

    Locate a V2in. to 1_/4n. (1.25 cm to 3.18 cm) vertical COLDwater pipe near the refrigerator.NOTE: Horizontal pipe will work, but drill on the top side ofthe pipe, not the bottom. This will help keep water away fromthe drill and normal sediment from collecting in the valve.

    4,

    5,

    Determine the length of copper tubing you need. Measurefrom the connection on the lower left rear of refrigerator to thewater pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use _/4n.(6.36 mm) O.D. (outside diameter) copper tubing. Be sureboth ends of copper tubing are cut square.Using a grounded drill, drill a _/4n. hole in the cold water pipeyou have selected.

    27. ...... .........3

    ! Cold WaterPipe 5 Compression Sleeve2. Pipe Clamp 6.Shutoff Valve3. Copper Tubing 7. Packing Nut4. Compression Nut

    6. Fasten the shutoff valve to the cold water pipe with the pipeclamp. Be sure the outlet end is solidly in the V4in. dri lled holein the water pipe and that the washer is under the pipe clamp.Tighten the packing nut. Tighten the pipe clamp screwscarefully and evenly so washer makes a watertight seal. Donot overtighten or you may crush the copper tubing.

    7. Slip the compression sleeve and compression nut on thecopper tubing as shown. Insert the end of the tubing into theoutlet end squarely as far as it will go. Screw compression nutonto outlet end with adjustable wrench. Do not overtighten.8. Place the free end of the tubing in a container or sink, andturn ON the main water supply. Flush the tubing until water is

    clear. Turn OFF the shutoff valve on the water pipe. Coil thecopper tubing.Connecting to Refrigerator

    1. Attach the copper tube to the valve inlet using a compressionnut and sleeve as shown. Tighten the compression nut. Donot overtighten. Use the tube clamp on the back of therefrigerator to secure the tubing to the refrigerator as shown.This will help prevent damage to the tubing when therefrigerator is pushed back against the wall.

    2. Turn shutoff valve ON.3, Check for leaks. Tighten any connections (includingconnections at the valve) or nuts that leak.

    ............................. /

    ............... 2

    ! Tube Clamp2 Copper Tubing

    3, Compression Nut4, Valve Inlet4. The ice maker is equipped with a built-in water strainer. If

    your water conditions require a second water strainer, installit in the V4in. (6.35 mm) water line at either tube connection.Obtain a water strainer from your nearest appliance dealer.5. Plug in refrigerator or reconnect power.

    8

  • 8/3/2019 Owner's Manual - Kenmore

    9/25

    Please read before using the water system.Immediately after installation, follow the steps below to makesure that the water system is properly cleaned.1. Open the freezer door and turn off the ice maker. For Style 1lift up the wire shutoff arm as shown. For Style 2 move theswitch to the OFF (right) setting as shown. The ON/OFFswitch is located on the top right side of the freezercompartment.Style 1

    Style 2

    NOTES: If your model has a base grille filter system, make sure thebase grille filter is properly installed and the cap is in thehorizontal position. Do not use with water that is microbiologically unsafe orof unknown quality without adequate disinfection beforeor after the system.2. Use a sturdy container to depress the water dispenser baruntil the water begins to flow. Flush the water system bydispensing and discarding 2 to 3 gal. (8 to 12 L) of water.Cleaning the system will take approximately 6 to 7 minutes

    and will help clear air from the line. Additional flushing may berequired in some households.NOTE: As air is cleared from the system, water may spurt outof the dispenser.

    3. Open the freezer door and turn on the ice maker. For Style 1lower the wire shutoff arm. For Style 2 move the switch to theON (left) position. Please refer to the "Ice Maker and StorageBin/Bucket" section for further instructions on the operationof your ice maker. Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Depending on your model, you may want to select themaximum ice feature to increase the production of ice.

    No SouYour new refrigerator may make sounds that your old one didn'tmake. Because the sounds are new to you, you might beconcerned about them. Most of the new sounds are normal. Hardsurfaces, such as the floor, walls, and cabinets, can make thesounds seem louder. The fol lowing describes the kinds of soundsand what may be making them. If your product is equipped with an ice maker, you will hear abuzzing sound when the water valve opens to fill the ice

    maker for each cycle.Your refrigerator is designed to run more efficiently to keepyour food items at the desired temperatures and to minimizeenergy usage. The high efficiency compressor and fans maycause your refrigerator to run longer than your old one. Youmay also hear a pulsating or high-pitched sound from thecompressor or fans adjusting to optimize performance.You may hear the evaporator fan motor circulating air throughthe refrigerator and freezer compartments. The fan speedmay increase as you open the doors or add warm food.Rattling noises may come from the flow of refrigerant, thewater line, or items stored on top of the refrigerator.Water dripping on the defrost heater during a defrost cyclemay cause a sizzl ing sound.As each cycle ends, you may hear a gurgling sound due tothe refrigerant flowing in your refr igerator.Contraction and expansion of the inside walls may cause apopping noise.You may hear air being forced over the condenser by thecondenser fan.

    You may hear water running into the drain pan during thedefrost cycle.

    REFRIGERATOR USEIn order to ensure proper temperatures, you need to permit air toflow between the two sections. Cold air enters the bottom of thefreezer section and moves up. It then enters the refrigeratorsection through the top vent. Air then returns to the freezer asshown.

    f

    I

    Do not block any of these vents with food such as soda, cereal,bread, etc. If the vents are blocked, airflow will be prevented andthe temperature controls will not function properly.

  • 8/3/2019 Owner's Manual - Kenmore

    10/25

    IMPORTANT:ecauseircirculatesetweenothsections,nyodorsormednonesectionwilltransferotheother.Youmustthoroughlyleanbothsectionsoeliminatedors.Topreventodorransferromood,wraporcoveroodsightly.

    ElectronicControlsonsomemodels}Foryourconvenience,ourcontrolsre preset at the factory,When instal ling your refrigerator, make sure that the controls arestill preset to the "mid-settings" as shown.

    FREI_B{ REFRI6ERATOR

    OOOOOOO OOOOOOO1 = _ @ 5 0 7 i = _ @ s i 7To turn on refrigerator: Press and hold ON/OFF for 2 seconds. The indicator lightsshow the current temperature control settings.

    NOTE: Settings to the left of the mid-setting make thetemperature less cold. Settings to the right of the mid-settingmake the temperature colder.IMPORTANT: The Refrigerator Control adjusts the refrigerator compartmenttemperature. The Freezer Control adjusts the freezercompartment temperature. Wait 24 hours after you turn on the refrigerator before you putfood into it. If you add food before the refrigerator has cooledcompletely, your food may spoil. Adjusting the Refrigeratorand Freezer Controls to a colder setting will not cool thecompartments any faster. If the temperature is too warm or too cold in the refrigerator orfreezer, first check the air vents to be sure they are notblocked, before adjusting the controls. The preset settings should be correct for normal householdusage. The controls are set correctly when milk or juice is ascold as you like and when ice cream is firm.Adjusting Electronic Controls

    NOTE: Wait at least 24 hours between adjustments. Recheck thetemperatures before other adjustments are made.If you need to adjust temperatures: Press the FREEZER or REFRIGERATOR arrow to move the

    indicator light to the right, one setting at a time. Continuemoving the indicator light until the desired setting is reached.

    o o s 7 INOTE: With each press of the arrow, you will hear a beep asthe light moves to the next setting. The indicator light movesto a setting of "7" and then returns to the setting of "1 " .

    CONDITION: SETTING ADJUSTMENT:Refrigerator too cold REFRIGERATOR Control- Not set correctly for one setting lowerconditionsRefrigerator too warm REFRIGERATOR Control- High use or room very warm one setting higherFREEZER too cold FREEZER Control one- Not set correctly for setting lowerconditionsFreezer too warm/too little ice FREEZER Control one- High use or heavy ice usage setting higher

    Additional Electronic Control Panel FeaturesAdditional features are located on the control panel at the top ofthe refrigerator compartment.Water Filter Indicator Light and ResetNOTE: Do not use with water that is microbiologically unsafeor of unknown quality without adequate disinfection beforeor after the system.The water filter display will help you know when to change yourwater filter cartridge. To change your filter, see the "Changing aBase Grille Filter" section.

    INDICATOR: STATUS:GOOD (green) New filter installedORDER (yellow) Order filter, 10% filter life remainsREPLACE (red) or when Replace water filterwater flow decreases

    After changing the water filter cartridge, reset the water filterindicator by pressing and holding the RESET for 2 seconds.The status light will change from Replace (red) to Good(green) when the system is reset,

    _O

    Accelerated Ice ProductionThe accelerated ice feature assists with temporary periods ofheavy ice usage by increasing ice production over a 24-hourperiod. Press ICE touch pad to set the freezer temperature to -10F(-23C). The Accelerated Ice setting will remain on for 24

    hours unless manually turned off.

    If increased ice production is desired at all times, set theFreezer Control to a colder setting. Adjusting the freezer to acolder temperature may make some foods, such as icecream, harder.

    10

  • 8/3/2019 Owner's Manual - Kenmore

    11/25

    Cut HazardUse a sturdy glass when dispensing ice or water.Failure to do so can result in cuts.

    Depending on your model, you may have one or more of thefollowing options: the ability to select either crushed or cubedice, a special light that turns on when you use the dispenser, or alock option to avoid accidental dispensing.The ice dispenser

    Ice dispenses from the ice maker storage bin in the freezer. Whenthe dispenser lever is pressed: A trap door opens in a chute between the dispenser and theice bin. Ice moves from the bin and falls through the chute. When you release the dispenser lever, the trap door closesand the ice dispensing stops. The dispensing system will notoperate when the freezer door is open.Some models dispense both cubed and crushed ice. Beforedispensing ice, select which type of ice you prefer. The buttoncontrols are designed for easy use and cleaning. For cubed ice, press the CUBE button until the red indicator

    appears in the window above the CUBE button.

    For crushed ice, press the CRUSH button until the redindicator appears in the window above the CRUSH button.For crushed ice, cubes are crushed before being dispensed. Thismay cause a slight delay when dispensing crushed ice. Noisefrom the ice crusher is normal, and pieces of ice may vary in size.When changing from CRUSH to CUBE, a few ounces of crushedice will be dispensed along with the first cubes.TO dispense ice:1. Press button for the desired type of ice.2. Press a sturdy glass against the ice dispenser lever. Hold theglass close to the dispenser opening so ice does not falloutside of the glass.

    3. Remove the glass to stop dispensing.NOTE: The first few batches of ice may have an off-flavorfrom new plumbing and parts. Throw the ice away. Also, takelarge amounts of ice from the ice bin, not through thedispenser.

    The water dispenserIf you did not flush the water system when the refrigerator wasfirst installed, press the water dispenser bar with a glass or jaruntil you draw and discard 2 to 3 gal. (8 to 12 L) or approximately6 to 7 minutes of water after water begins dispensing. It will take3 to 4 minutes for the water to begin dispensing. The water youdraw and discard cleans the system and helps clear air from thelines. Allow several hours for the refrigerator to cool down andchill water.IMPORTANT: Depending on your model, the small removabletray at the bottom of the dispenser is designed to catch smallspills and allow for easy cleaning. There is no drain in the tray.The tray can be removed from the dispenser and carried to thesink to be emptied or cleaned.

    JTo dispense water:1. Press a glass against the water dispenser lever.2. Remove the glass to stop dispensing.NOTE: Dispense enough water every week to maintain a freshsupply.

    The dispenser lightThe dispenser area has a light. It can be turned on manually bypressing the QN button at the right-hand side of the controlpanel. The red indicator above the QN button will appear.Qn some models: Whenever you use the dispenser the lever willautomatically turn the light on.

    LIGHTOFF ON

    NOTE: See the "Changing the Light Bulbs" section forinformation on changing the dispenser light bulb.On models without crushed ice, the light switch is a rocker-styletype. Push the switch to turn the light on, and push again to turnthe light off.

    IMPORTANT: You do not need to apply a lot of pressure tothe lever in order to activate the ice dispenser. Pressing hardwill not make the ice dispense faster or in greater quantities.11

  • 8/3/2019 Owner's Manual - Kenmore

    12/25

    The dispenser lock (on some models) Style 1: Behind the base grille filterYour dispenser can be turned off for easy cleaning or to preventaccidental dispensing by small children and pets. To turn off thedispenser, press the LOCK button. The indicator will appearabove the LOCK button and the ice and water dispensers will notwork. To unlock the dispenser, press the UNLOCK button untilthe indicator appears. Then continue to dispense ice or water asusual.

    1. Remove the base grille (see "Removing the base grille"section). Rotate the cartridge counterclockwise to a verticalposition and pull the filter cartridge out.NOTE: There will be water in the cartridge. Some spilling mayoccur.

    DISPENSERLOCK UNLOCK

    NOTE: The lock feature does not shut off power to the product,to the ice maker, or to the dispenser light. It simply deactivatesthe dispenser levers.

    The base grille water filter status light (on some models)The water filter status light will help you know when to changeyour water filter cartridge. The light is located at the top of therefrigerator compartment. The light will change from green toyellow. This tells you that it is almost time to change the waterfilter cartridge (90% of the filter life has been used). It isrecommended that you replace the base grille water filtercartridge when the water filter indicator light changes to red ORwater flow to your water dispenser or ice maker decreasesnoticeably. (See "Changing a base grille water f il ter cartridge"later in this section.)NOTE: Do not use with water that is microbiologically unsafeor of unknown quality without adequate disinfection beforeor after the system.

    1. Status Light2. Light Switch

    After changing the water filter cartridge, reset the water filterstatus light by pressing the light switch 5 times within 10seconds. The status light will change from red to green when thesystem is reset.Non-indicator water filter (on some models)

    If your refrigerator does not have the water filter status light, youshould change the water filter cartridge every 6 to 9 monthsdepending upon your usage. If the water flow to the waterdispenser or ice maker decreases noticeably before 6 monthshave passed, replace the water fi lter cartridge more often.

    Changing a base grille water filter cartridgeThe base grille water filter is located below the freezercompartment door. Depending on your model, you may have afilter that is located behind the base grille (Style 1) or a filter thatis located through the base grille (Style 2).

    2. Take the new cartridge out of its packaging and removeprotect ive cover from o-rings.3. Push the new filter cartridge into the base until it stops.Rotate the cartridge clockwise to a horizontal posi tion. Flushthe water system (see "Flushing the Water System AfterReplacing Filter" later inthis section).

    Style 2: Through the base grille filter1. Locate the water filter cartridge cap in the front base grille.Rotate the cap counterclockwise to avertical position andpull the cap and filter cartridge out through the base grille.

    NOTE: There will be water in the cartridge. Some spilling mayOCCUR

    2. Remove the cartridge cap by sliding it off the end of the oldcartridge. The cap will slide to the left or right. DO NOTDISCARD THE CAR

    3. Take the new cartridge out of its packaging and removeprotect ive cover from o-rings.

    4. Slide the cartridge cap onto the new cartridge. Seeillustration in Step 2.5. With cartridge cap in t he vertical position, push the new filter

    cartridge into the base grille unti l it stops. Rotate the cartridgecap clockwise to a horizontal position. Flush the watersystem (see "Flushing the Water System After ReplacingFilter" later in this section).

    12

  • 8/3/2019 Owner's Manual - Kenmore

    13/25

    Flushing the Water System After Replacing FilterUse a sturdy container to depress the water dispenser bar untilthe water begins to flow. Flush the water system by dispensingand discarding 2 to 3 gal. (8 t o 12 L) o f water. Cleaning thesystem will take approximately 6 to 7 minutes and will help clearair from the line. Additional flushing may be required in somehouseholds.NOTE: As air is cleared from the system, water may spurt out ofthe dispenser.Using the dispenser without the water filter

    You can run the dispenser without a water filter cartridge. Yourwater will not be filtered.1. Remove the base grille water filter cartridge. For Style 1,replace the base grille after removing the fi lter.2. For Style 2, slide the cartridge cap off the end of the filtercartridge. DO NOT DISCARD THE CAR With the cartridgecap in the vertical position, insert the cap into the base grilleunti l i t stops.

    3. Rotate the cartridge cap to a horizontal position. Thecartridge cap might not be even with the base grille.

    To turn the ice maker on/off (Style 1):The on/off switch for the ice maker is a wire shutoff arm locatedon the side of the ice maker.1. To turn the ice maker on, simply lower the wire shutoff arm.NOTE: Your ice maker has an automatic shutoff. As ice is

    made, the ice cubes will fill the ice storage bin and the icecubes will raise the wire shutoff arm to the OFF (arm up)position.2. To manually turn the ice maker off, lift the wire shutoff arm tothe OFF (arm up) position and listen for the click to make surethe ice maker will not continue to operate.

    To increase ice production rate: Normal Ice Production: In normal ice production mode, theice maker should produce approximately 7 to 9 batches of icein a 24-hour period. If ice is not being made fast enough, turn

    the Freezer Control toward a higher (colder) number in halfnumber steps. (For example, if the control is at 3, move it tobetween 3 and 4.) Wait 24 hours between each increase. Maximum Ice Production (on some models): In maximum iceproduction, the ice maker should produce approximately 10to 14 batches of ice in a 24-hour period. If your refrigerator

    has the maximum ice production feature, push the switch toMAX.To remove and replace freezer shelf ice bin (Style 1):1. Pull the covering panel out from the bottom and then slide itback toward the rear.2. Lift the wire shutoff arm so it clicks into the OFF (up) position.Ice can still be dispensed, but no more can be made.3. Lift up the front of the storage bin and pull it out.

    4. Replace the bin by pushing it in all the way or the dispenserwill not work. Push the wire shutoff arm down to the ONposition to restart ice production. Make sure the door isclosed tightly.

    To turn the ice maker on/off (Style 2):The ON/OFF switch is located on the top right side of the freezercompartment.1. To turn the ice maker on, slide the control to the ON (left)position.

    NOTE: Your ice maker has an automatic shutoff. The icemaker sensors will automatically stop ice production, but thecontrol wil l remain in the ON (left) position.

    2. To manually turn the ice maker off, slide the control to theOFF (right) position.

    To remove and replace freezer door ice bucket (Style 2}:1. Place four fingers in bucket base opening and rest thumb onthe release button.2. Holding the base of the bucket with both hands, depress therelease button and lift the bucket up and out. It is notnecessary to turn the ice maker control to the OFF (right)

    position. The ice maker will not produce ice without thebucket installed in the door.

    /

    To care for ice storage bin or bucket:1. Empty the ice container. Use warm water to melt the ice if

    necessary.NOTE: Never use anything sharp to break up the ice in thebin or bucket. This can cause damage to the ice containerand the dispenser mechanism.

    13

  • 8/3/2019 Owner's Manual - Kenmore

    14/25

    2. Wash ice bin or bucket with a mild detergent, rinse well and 2. Replace the shelf by guiding it back into the slots on thedry thoroughly. Do not use harsh or abrasive cleaners or frame and pushing the shelf in past the stop.solvents.REMEMBER: Allow 24 hoursto produce the first batch of ice. Discard the first three batches of ice produced to avoidimpurities that may be flushed out of the system. The quality of your ice will be only as good as the quality ofthe water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply.Water softener chemicals (such as salt) can damage parts ofthe ice maker and lead to poor quality ice. If a softened watersupply cannot be avoided, make sure the water softener isoperating properly and is well maintained.

    It is normal for the ice cubes to be attached at the corners.They wi ll break apart easily.For Style I ice maker, do not force the wire shutoff arm up ordown.

    Do not store anything on top of or in the ice maker or ice binor bucket.

    REFRIGERATORFEATURESYour model may have some or all of these features. Features thatcan be purchased separately as product accessories are labeledwith the word "Accessory." Not all accessories will fit all models.Ifyou are interested in purchasing one of the accessories, pleasecall the toll-free number on the cover or in the "Accessories"section.Important information to know about glass shelvesand covers:Do not clean glass shelves or covers with warm water whenthey are cold. Shelves and covers may break if exposed tosudden temperature changes or impact, such as bumping.For your protection, tempered glass isdesigned to shatterinto many smal l, pebble-size pieces. This is normal. Glassshelves and covers are heavy. Use special care when re-moving them to avoid impact from dropping.

    Shelves and Shelf FramesTo remove and replace a shelf/freme:1. Remove the shelf/frame by tilting it up at the front and lifting itout of the shelf supports.2. Replace the shelf/frame by guiding the rear shelf hooks intothe shelf supports. Tilt the front of the shelf up until rear shelfhooks drop into the shelf supports. Check to make sure thatthe shelf issecurely in position.

    To raise or lower the shelf:.1. Raise the shelf by pulling forward on the lever located at thebottom front of the shelf and lift until the shelf locks into the

    vertical position.2. Lower the shelf until it is latched securely in place.

    Your model may have glass or wire shelves. Store similar foodstogether and adjust the shelves to fit different heights. Thisreduces the time the refrigerator door is open and saves energy.Slide-out Shelves (on some models)

    To remove and replace a shelf in a metal frame:1. Pull the shelf forward to the stop. Tilt the front of the shelf upand lift it slightly as you pull the shelf from the frame.

    To raise or lower the shelf:.1. Raise the shelf by first sliding it back and down to make ithalf-width. (You can use the shelf in this position to allowtaller items to be stored on the shelf below.)2. Lift the front of the shelf until it fits securely in place againstthe back wall. Lower the shelf securely back into position.3. Pull the front of the shelf forward until it fits into place.

    I

    14

  • 8/3/2019 Owner's Manual - Kenmore

    15/25

    The dell drawer stores raisins, nuts, spreads, and other smallitems at normal refrigerator temperatures.TO remove and replace the dell drawer:1. Remove the dell drawer by sliding it straight out to the stop.Lift the front and slide the drawer out the rest of the way.2. Replace the dell drawer by sliding it back past the stop.

    Crisper and Convertible Vegetable Meat DrawersTo remove and replace drawers:1. Slide crisper or meat drawer straight out to the stop. Lift thefront of drawer with one hand while supporting the bottom ofdrawer with other hand and slide the drawer out the rest of

    the way.2. Replace the crisper or meat drawer by sliding it back in fullypast the drawer stop.Crisper or Vegetable/Meat Drawer Covers

    To remove and replace covers:1. Remove the crisper and meat drawer. Press up in center of

    crisper glass insert until it rises above the plastic frame.Holding the crisper glass firmly, carefully slide the glass insertforward to remove.2. Lift crisper cover frame and remove. Repeat steps to removethe meat drawer cover.

    3. Replace back of meat drawer cover frame into supports orslides on side walls of the refrigerator and lower or slide thefront of the cover frame into place.4. Slide rear of glass insert into cover frame and lower front intoplace. Repeat steps to replace the crisper cover.

    The convertible vegetable/meat drawer can be adjusted toproperly chill meats or vegetables. The air inside the pan iscooled to prevent "spot" freezing and can be set to keep meatsat the National Livestock and Meat Board recommended storagetemperatures of 28- 32F (-2- 0C).

    IMPORTANT: To extend freshness, wrap meats in airtight,moisture-proof materials before storing. Always store meat asrecommended.Adjusting the controlThe convertible control comes preset at the lowest meat setting.To change a control setting: Move the control to the right (colder)or to the left (less cold) as desired.To store vegetables: Set the control to VEG (all the way to the left)to store vegetables at their optimal storage temperatures (whichneed to be warmer than those for meat).

    IMPORTANT: If food starts to freeze, move the control to the left(less cold). Remember to wait 24 hours between adjustments.Doing so gives the temperature of the food time to change.Meat storage guideStore most meat in original wrapping as long as it is airtight andmoisture-proof. Rewrap if necessary. See the following chart forstorage times. When storing meat longer than the times given,freeze the meat.Fresh fish or shellfish .. ... .. .. ... .. .. . use same day as purchasedChicken, ground beef, variety meat (liver, etc.) .. ... .. .. 1-2 daysCold cuts, steaks/roasts ........................................... 3-5 daysCured meats ........................................................... 7-10 daysLeftovers - Cover leftovers with plastic wrap, aluminum foil, orplastic containers with tight lids.

    You can control the amount of humidity in the moisture-sealedcrisper. Adjust the control to any setting between LOW andHIGH.LOW (open) lets moist air out of the crisper for best storage offruits and vegetables with skins. Fruit: Wash, let dry and store in refrigerator in plastic bag orcrisper. Do not wash or hull berries until they are ready to use.Sort and keep berries in original container in crisper, or storein a loosely closed paper bag on a refrigerator shelf. Vegetables with skins: Place in plastic bag or plasticcontainer and store in crisper.HIGH (closed) keeps moist air in the crisper for best storage offresh, leafy vegetables. Leafy vegetables: Wash in cold water, drain and trim or tearoff bruised and discolored areas. Place in plastic bag orplastic container and store in crisper.Humidity control location: Humidity Control oncrisper drawer (Style 1 - on left) Humidity Control on crisper cover (Style 2 - on right)

    HIs_ S 4 3 2 I Low

    15

  • 8/3/2019 Owner's Manual - Kenmore

    16/25

    Ca JB< Ateo_ s{ '_es(xSes-Accesso'y

    To remove and replace the wine rack (left) or can/bottlerack (right):1. Remove the rack by pulling it straight out from the shelf.2. Replace the rack by sliding it in between the shelf and thewall of the refrigerator.

    The freezer basket or bin can be used to store bags of frozenfruits and vegetables that may slide oft freezer shelves.TO remove and replace the freezer basket or bin:1. Remove basket or bin by sliding it out to the stop.2. Lift the front of the basket or bin and slide it o ut the rest of the

    way.

    NOTE: For long-term storage, place eggs in a covered containeror in their original carton on an interior shelf.

    FEATURESYour model may have some or all of these features. Features thatcan be purchased separately as product accessories are labeledwith the word "Accessory." Not all accessories will fit all models.Ifyou are interested in purchasing one of the accessories, pleasecall the toll-free number on the cover or in the "Accessories"section.To remove and replace the shelf:.1. Lift the shelf off of the supports.2. Slide it out of the shelf support holes.3. Replace shelf in the reverse order.

    Frozen food storage guideStorage times will vary according to the quality and type of food,the type of packaging or wrap used (should be airtight andmoisture-proof), and the storage temperature. Ice crystals insidea sealed package are normal. This simply means that moisture inthe food and air inside the package have condensed, creating icecrystals.Put no more unfrozen food into the freezer than will freeze within24 hours (no more than 2 to 3 Ibs. of food per cubic foot[907-1,350 g per L] of freezer space). Leave enough space in thefreezer for air to circulate around packages. Be careful to leaveenough room for the door to close tightly.For more information on preparing food for freezing, check afreezer guide or reliable cookbook.

    3, Replace the basket or bin by positioning it on the side wallguide rails. Lift the basket or bin front slightly while pushing itpast the guide rail stops and slide basket or bin in the rest ofthe way.

    DOOR FEATURESYour model may have some or all of these features. Features thatcan be purchased separately as product accessories are labeledwith the word "Accessory." Not all accessories will fit all models.If you are interested in purchasing one of the accessories, pleasecall the toll-free number on the cover or in the "Accessories"section.

    The door rails may be removed for easier cleaning.Snap-on Door Rails

    To remove and replace the rails:1. Remove the rails by pushing in slightly on the front of thebracket while pulling out on the inside tab. Repeat thesesteps for the other end of the rail.2. Replace the rails by aligning the ends of the brackets with thebuttons on the sides of the door liner, Firmly snap bracketand rail assembly onto the tabs above the shelf as shown.

    Drop-in Door RailsTo remove and replace the rails:1.2.

    Remove the rails by pulling straight up on each end of the railReplace the rails by sliding the shelf rail into the slots on thedoor and pushing the rail straight down until it stops.

    16

  • 8/3/2019 Owner's Manual - Kenmore

    17/25

    NOTE: Can racks may be purchased as an Accessory for somemodels,TO remove and replace the racks/bins:1. Remove the racWbin by lifting it and pulling it straight out.2. Replace the rack/bin by sliding it in above the desiredsupport and pushing it down until it stops.

    REFRIGERATOR CARE

    Explosion HazardUse nonflammable cleaner.Failure to do so can result in death, explosion,or fire.

    Both the refrigerator and freezer sections defrost automatically.However, clean both sections about once a month to preventodors from building up. Wipe up spi lls immediately.Cleaning your refrigerator1. Unplug refrigerator or disconnect power.2. Remove all removable parts from inside, such as shelves,crispers, etc.3. Hand wash, rinse, and dry removable parts and interiorsurfaces thoroughly. Use a clean sponge or soft cloth and amild detergent in warm water.

    Do not use abrasive or harsh cleaners such as windowsprays, scouring cleansers, f lammable f luids, cleaningwaxes, concentrated detergents, bleaches or cleanserscontaining petroleum products on plastic parts, interiorand door liners or gaskets. Do not use paper towels,scouring pads, or other harsh cleaning tools. These canscratch or damage materials.

    To help remove odors, you can wash interior walls with amixture of warm water and baking soda (2 tbs. to 1 qt.[26 g to .95 L] of water).4. Wash stainless steel and painted metal exteriors with a cleansponge or soft cloth and a mild detergent in warm water. Donot use abrasive or harsh cleaners. Dry thoroughly with a softcloth. For additional protection against damage to painted

    5.

    metal exteriors, apply appliance wax (or auto paste wax) witha clean, soft cloth. Do not wax plastic parts.NOTE: To keep your Stainless Steel refrigerator looking l ikenew and to remove minor scuffs or marks, it is suggested thatyou use the manufacturer's approved Stainless Steel Cleaner& Polish.IMPORTANT: This cleaner is for Stainless Steel parts only!Do not allow the Stainless Steel Cleaner & Polish to come intocontact with any plastic parts such as the trim pieces,dispenser covers or door gaskets. If accidental contact doesoccur, clean plastic part with a sponge and mild detergent inwarm water. Dry thoroughly with a soft cloth. To order thecleaner, see the "Accessories" section.There is no need for routine condenser cleaning in normalhome operating environments. If the environment isparticularly greasy or dusty, or there is signi ficant pet traffic inthe home, the condenser should be cleaned every two tothree months to ensure maximum efficiency.If you need to clean the condenser: Remove the base grille (see "Base Grille" or "DoorRemoval" section). Use a vacuum with a soft brush to clean the grille, theopen areas behind the grille and the front surface area ofthe condenser. Replace the base grille when finished.

    6. Plug in refrigerator or reconnect power.B

  • 8/3/2019 Owner's Manual - Kenmore

    18/25

    Refrigerator Crisper Light or Upper Freezer Light (on somemodels) Remove light shield by grasping the top center of the shieldand pulling forward while turning it slightly to one side. Ifnecessary, remove top crisper drawer to access crisper lightshield.

    Replace the light shield by inserting the tabs on one end intothe slotted holes in the refrigerator or freezer liner. Then,carefully bend the shield at the center to insert the tabs onthe other end.

    Upper Freezer Light (on some models) Remove the light shield by grasping the sides and squeezingin toward the center and while pulling forward the shield.

    Replace the light shield by fitting the tabs into the slottedholes in the freezer liner. Push in the shield until it snaps intoplace.

    Lower Freezer Light Beneath Ice Bin (on some models) Remove the light shield by grasping the sides and squeezingin t oward the center. Once the side hooks of shield are free

    from the freezer lining, pull down the shield.Replace the light shield by squeezing the sides toward thecenter and inserting the side hooks into the slotted holes.Once the side hooks are in place, snap the front tab into theslotted hole.

    Lower Freezer Light Behind Top Freezer Basket (on somemodels) Depending on your model, remove the top freezer basket ortop freezer basket shelf. Remove light shield by removing thePhillips screw on the top of the shield. Carefully, rotate the

    shield until the left tab can be gently pulled from the freezerwall. Replace the light shield by inserting the left tab into thefreezer wall. Align top tab with screw hole and replace screw.

    If the power will be out for 24 hours or less, keep both refrigeratordoors closed to help food stay cold and frozen.If the power will be out for more than 24 hours, do one of thefollowing: Remove all frozen food and store it in a frozen food locker. Place 2 Ibs. (907 g) of dry ice in the freezer for every cubicfoot (28 L) of freezer space. This will keep the food frozen for

    two to four days. If neither a food locker nor dry ice is available, consume orcan perishable food at once.REMEMBER: A full freezer stays cold longer than a partia lly filledone. A freezer full of meat stays cold longer than a freezer full ofbaked goods. If you see that food contains ice crystals, it may berefrozen, although the quality and flavor may be affected. If thecondition of the food is poor, dispose of it.

    Vacations

    If you choose to leave the refrigerator on while you're away:1. Use up any perishables and freeze other items.2. If your refrigerator has an automatic ice maker:

    Raise wire shutoff arm to OFF (up) position or move theswitch to the OFF (right) setting. Shut off water supply to the ice maker.

    3. Empty the ice bin.If you choose to turn the refrigerator off before you leave:1. Remove all food from the refrigerator.2. If your refrigerator has an automatic ice maker:

    Turn off the water supply to the ice maker at least one dayahead of time. When the last load of ice drops, raise the wire shutoff armto the OFF (up) position or move the switch to the OFF(right) setting.

    3. Depending on your model, turn the Thermostat Control orRefrigerator Control to QFR See the "Setting or Using theControl(s)" section.4. Clean refrigerator, wipe it, and dry well.5. Tape rubber or wood blocks to the tops of both doors to propthem open far enough for air to get in. This stops odor andmold from building up.Moving

    When you are moving your refrigerator to a new home, followthese steps to prepare it for the move.1. If your refrigerator has an automatic ice maker:

    Turn off the water supply to the ice maker at least one dayahead of time. Disconnect the water line from the back of the

    refrigerator. When the last load of ice drops, raise the wire shutoff armto the OFF (up) position or move the switch to the OFF(right) setting.

    2. Remove all food from the refrigerator and pack all frozen foodin dry ice.3. Empty the ice bin.

    18

  • 8/3/2019 Owner's Manual - Kenmore

    19/25

    4. Depending on your model, turn the Thermostat Control orRefrigerator Control to OFR See the "Setting or Using theControls" section.5. Unplug the refrigerator.6. Empty water from the defrost pan.7. Clean, wipe, and dry thoroughly.8. Take out all removable parts, wrap them well, and tape themtogether so they don't shift and rattle during the move.9. Depending on the model, raise the front of the refrigerator soit rolls more easily OR screw in the leveling legs so they don't

    scrape the floor. See the "Door Closing" or "Leveling YourRefrigerator" section.10. Tape the doors shut and the power cord to the refrigeratorcabinet.When you get to your new home, put everything back and refer tothe "Refrigerator Installation" section for preparation instruct ions.Also, i f your refrigerator has an automatic ice maker, remember toreconnect the water supply to the refrigerator.

    1ROUBLESHOOTINGTry the solutions suggested here first in order to avoid thecost of an unnecessary service call,Your refrigerator will not operate

    Is the power supply cord unplugged? Plug into a grounded3 prong outlet. Has a household fuse or circuit breaker tripped? Replacethe fuse or reset the circuit breaker. Is the refrigerator or freezer control turned to the OFFposition? Refer to the "Setting or Using the Controls"section. Is the refrigerator defrosting? Recheck to see if therefrigerator is operating in 30 minutes, Your refrigerator wil lregularly run an automatic defrost cycle. Is the refrigerator not cooling? For models with digitalcontrols, turn the unit OFF then ON again to reset. See the"Setting or Using the Controls" section. If this does notcorrect the problem, cal l for service.The lights do not work

    Is the power supply cord unplugged? Plug into a grounded3 prong outlet. Is a light bulb loose in the socket or burned out? See the"Changing the Light Bulb(s)" section,There is water in the defrost drain pan

    Is the refrigerator defrosting? The water will evaporate. It isnormal for water to drip into the defrost pan. Is it more humid than normal? When it is humid, expect thatthe water in the defrost pan will take longer to evaporate.The motor seems to run too much

    Has a large amount of food just been added to therefrigerator? Adding a large amount of food warms therefrigerator. The motor normally will run longer to cool therefrigerator back down.Are the doors opened often? The motor will run longerwhen this occurs. Conserve energy by getting all items out atone time, keeping food organized, and closing the door assoon as possible.Are the controls not set correctly for the surroundingconditions? Refer to the "Setting or Using the Controls"section.Are the doors not closed completely?. Close the doorsfirmly. If they do not close completely, see "The doors will notclose completely" later in this section.Are the condenser coils dirty? This prevents air transfer andmakes the motor work harder. Clean the condenser coils.Refer to the "Cleaning" section.Are the door gaskets not sealed all the way around?Contact a technician or other quali fied person.NOTE: Your new refrigerator will run longer than your old onedue to its high-efficiency motor.

    _,J_J_J_J_J_,,,,,_,_,,,,,,,,,,,,,,,,,,,,,,_,,_,,,,,,,,,,,,,,,,,,,,,Theefrigerator seems to make too much noise The sounds may be normal for your refrigerator. See the"Normal Sounds" section.

    The ice maker is not producing ice or not enough ice Has the ice maker just been installed? Wait 72 hours for fullice production to begin. Once your refrigerator is cooled, theice maker should produce 70 to 120 cubes every 24 hours.

    Is the freezer temperature cold enough to produce ice?Wait 24 hours after ice maker hook-up for ice production. Seethe "Setting or Using the Controls" section.Is the ice maker wire shutoff arm in the OFF (arm up)position (on some models)? Lower the wire shutoff arm tothe ON (arm down) position. See the "ice Maker and StorageBin/Bucket" section.Is the ice maker switch in the OFF (right) position (onsome models)? Move ice maker switch to the ON (left)position. See the "ice Maker and Storage Bin/Bucket"section.

    Is the water line shutoff valve to the refrigerator turnedon? Turn on the water valve. See the "Water SupplyConnection" section.

    Is the room temperature hotter than normal? The motorwill run longer under warm conditions. At normal room temperatures, expect your motor to run about 40% to 80% ofthe time. Under warmer conditions, it will run even more.

    Does the ice maker mold have water in it or has no icebeen produced? Make sure your refrigerator has beenconnected to a water supply and the supply shutoff valve isturned on. See the "Water Supply Connection" section.Is an ice cube jammed in the ice maker ejector arm?For models with an interior ice bin, remove the ice from theejector arm with a plastic utensil. For models with an icebucket located on the freezer door, access the ice maker bydepressing the ice sensor door on the upper left side of thefreezer interior. While depressing the sensor door, l ift the icemaker service door and remove the ice from the ejector witha plastic utensi l. See the "ice Maker and Storage Bin/Bucket"section.Has a large amount of ice just been removed? Allow 24hours for ice maker to produce more ice.Are the controls set correctly? See the "Setting or Usingthe Controls" section.

    19

  • 8/3/2019 Owner's Manual - Kenmore

    20/25

    Is there a water filter installed on the refrigerator? The filter may be clogged or installed incorrectly. Check the filterinstal lation instructions to ensure that the fi lter was instal ledcorrectly and is not clogged. If installation or clogging is not a problem, call a technician or other quali fied person.

    NOTE; If not due to any of the above, there may be a problemwith the water l ine. Cal l for service.Off-taste, odor or gray color in the ice

    Are the plumbing connections new, causing discolored oroff-flavored ice? Discard the first few batches of ice.Have the ice cubes been stored too long? Throw old iceaway and make a new supply.Does the freezer and ice bin or bucket need to becleaned? See the "Cleaning" or "Ice Maker and Storage Bin/Bucket" section.Has food in the freezer or refrigerator been wrappedproperly? Use airtight, moisture-proof packaging to helpprevent odor transfer to stored food.Does the water contain minerals (such as sulfur)? A filtermay need to be installed to remove the minerals.Is there a water filter installed on the refrigerator? Gray ordark discoloration in ice indicates that the water filtrationsystem needs additional flushing. Run additional waterthrough the water dispenser to flush the water filtrationsystem more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to7 minutes initially). Discard discolored ice.

    Is there ice in the bucket? See "The ice maker is notproducing ice" earlier in this section.Has the dispenser arm been held in too long? Releasedispenser arm. Ice will stop dispensing when the arm is hein too long. Wait three minutes for dispenser motor to resetbefore using again. It is best to take large amounts of icedirectly from the ice bin or bucket, not through the dispense

    Ice bucket difficult to removeIs the ice bucket difficult to remove (on some models)?For models with an ice bucket located on the freezer door,select "cubed" ice. Using a sturdy glass, quickly depress arelease the ice dispenser arm. Open the freezer door, depresthe release button on the ice bucket and lift upward. Referthe "Ice Maker and Storage Bin/Bucket" section.

    The water dispenser will not operate properly

    The ice dispenser will not operate properly Is the freezer door closed completely? Push the door f irmlyshut. If it will not shut all the way, see "The doors will notclose completely" later in this section.

    Is the ice bin or bucket installed correctly? For modelswith an interior ice bin, push the ice bin in all the way. If theice bin does not go ina ll the way, it may not be put ins traight.Pull it out and try again. For models with an ice bucketlocated on the freezer door, the bucket should sit level. Toremove the bucket, press the release button on the right sideof the bucket and lift straight up. Replace the bucket in thedoor making sure it is properly aligned and snapped securelyinto place. Refer to the "Ice Maker and Storage Bin/Bucket"section.Has the wrong ice been added to the bin or bucket? Useonly cubes produced by the current ice maker. If other cubeshave been added, remove all cubes and check to see thatnone have become stuck in the delivery chute.Has the ice frozen in the ice bin or bucket? Shake the icebin or bucket to separate cubes. If cubes do not separate,empty bin or bucket and wait 24 hours for ice to restock.Has the ice melted around the auger (metal spiral) in theice bucket? Dump the ice cubes and clean the ice bucketcompletely. Allow 24 hours for the ice maker to restock. Donot try to remove the melted ice with a sharp object. Youcould damage the ice bucket.Is ice stuck in the delivery chute? Clear the ice from thedelivery chute with a plastic utensil. Do not use anythingsharp to remove the ice. You could cause damage.Is the ice dispenser stalling while dispensing "crushed"ice? Stop dispensing ice. Change the ice button from"crushed" to "cubed." Depress the ice dispenser arm using asturdy glass. If cubed ice dispenses correctly, depress thebutton for "crushed" ice and begin dispensing again. Refer tothe "Water and Ice Dispensers" section.

    Has the water system not filled? The water system needsto be filled the first time it is used. Use a sturdy container tdepress the water dispenser bar until the water begins toflow. Flush the water system by dispensing and discarding2 to 3 gal. (8 to 12 L) o f water. Cleaning the system will takeapproximately 6 to 7 minutes and will help clear air from thline. Addit ional f lushing may be required in some householdsSee the "Water and Ice Dispensers" section.Is the water shutoff valve not turned on or the water linconnected at the source? Make sure the water shutoff valis turned on and the water source is connected to therefrigerator. See the "Water Supply Connection" section.Is the water shutoff valve clogged or incorrectly installedSee the "Water Supply Connection" section. If clogging orinstallation is not a problem, call for service or contact aplumber.Is there a kink in the home water source line? If you findsuspect a kink in the water line, call for service.Is there a water filter installed on the refrigerator? Thefilter may be clogged or incorrectly installed. First, check thfilter instal lation instructions to ensure that the fi lter wasinstalled correctly and is not clogged. If installation orclogging is not a problem, call for service.

    Water or ice is leaking from the dispenserIs the glass not being held under the ice dispenser longenough, causing the ice to spill? Hold the container undethe ice chute for two to three seconds after releasing thedispenser lever. Water or ice may continue to dispense durinthis time.Is an ice cube stuck in the chute and holding the trapdoor open? Remove the cube.Is there a water filter installed on the refrigerator? Thewater filtration system may have air in the lines, causing watto drip. Additional flushing may help clear air from the linesNormal dispenser use should flush air from the lines withinto 72 hours.

    Water flow from the dispenser decreases noticeablyIs there a water filter installed on the refrigerator?The filter may be full or incorrectly installed. Remove thewater fil ter cartridge (see the "Water Fi ltration System"section). Operate the dispenser. If the water flow increasesnoticeably, replace the fi lter.

    20

  • 8/3/2019 Owner's Manual - Kenmore

    21/25

    The dispenser water is not cool enough The doors will not close completely Has the refrigerator been newly installed? Allow 24 hours Are food packages blocking the door open? Rearrangefor the refrigerator to cool completely. Has a large amount of water been recently dispensed?Allow 24 hours for the water to cool completely. Has water not been recently dispensed? The first glass ofwater may not be cool. Discard the first glass of water.

    The divider between the two compartments is warmThe warmth is probably due to normal operation of theautomatic exterior moisture control . If stil l concerned, call forservice.

    containers so that they fit more tightly and take up lessspace.Is the ice bin or ice bucket out of position? Formodelswith an interior ice bin, push the ice bin in all the way. If theice bin does not go in all the way, it may not be put in straight.Pull it out and try again. For models with an ice bucketlocated on the freezer door, the bucket should sit level. Toremove the bucket, press the release button on the right sideof the bucket and lift straight up. Replace the bucket in thedoor making sure it is properly aligned and snapped securelyinto place. See the "ice Maker and Storage Bin/Bucket"section.

    Temperature is too warm Are the air vents blocked in either compartment? Thisprevents the movement of cold air from the freezer to therefrigerator. Remove any objects from in front of the air vents.

    See the "Ensuring Proper Air Circulation" section for thelocation of air vents. Are the door(s) opened often? The refr igerator wil l warm

    when this occurs. Keep the refrigerator cool by getting allitems out at one time, keeping food organized, and closingthe door as soon as possible. Has a large amount of food just been added to therefrigerator or freezer? Adding a large amount of food

    warms the refrigerator. It can take several hours for therefrigerator to return to the normal temperature. Are the controls set correctly for the surroundingconditions? See the "Setting or Using the Controls" section. Is the refrigerator not cooling? For models with digitalcontrols, turn the unit OFF then ON again to reset. See the"Setting or Using the Controls" section. If this does notcorrect the problem, cal l for service.There is interior moisture buildup

    Are the air vents blocked in the refrigerator? Remove anyobjects from in front of the air vents. See the "EnsuringProper Air Circulation" section for the location of air vents.

    Are the door(s) opened often? Avoid humidity buildup bygetting all items out at one time, keeping food organized, andclosing the door as soon as possible.

    Is the room humid? It is normal for moisture to build upinside the refrigerator when the room air is humid. Is the food packaged correctly? Check that all food is

    securely wrapped. Wipe off damp food containers beforeplacing in the refrigerator. Are the controls set correctly for the surroundingconditions? See the "Setting or Using the Controls" section. Was a self-defrost cycle completed? It is normal fordroplets to form after the refrigerator self-defrosts.

    Are the pans, shelves, bins, or baskets out of position?Put the crisper cover and all pans, shelves, bins, and basketsback into their correct positions. See the "Crisper and CrisperCovers" section for more information.Are the gaskets sticking? Clean gaskets according to thedirections inthe "Cleaning" section.Does the refrigerator wobble or seem unstable? Level therefrigerator. See the "Door Closing" or "Leveling Refrigerator"section, depending on your model.Were the doors removed during product installation andnot properly replaced? Remove and replace the doorsaccording to the "Door Removal" section on some models, orcall a qualified service technician.

    The doors are difficult to open Are the gaskets dirty or sticky?. Clean gaskets according tothe directions in the "Cleaning" section.

    Computer Troubleshooting (on some models)See the "Computer and Software User Guide" for informationregarding your computer system.

    21

  • 8/3/2019 Owner's Manual - Kenmore

    22/25

    SERVICEMaster Protection AgreementsCongratulations on making a smart purchase. Your newKenmore_"_appliance is designed and manufactured for years ofdependable operation. But like all products, it may requirepreventive maintenance or repair from time to time. That's whenhaving a Master Protection Agreement can save you money andaggravation.Purchase a Master Protection Agreement now and protectyourself from unexpected hassle and expense.The Master Protection Agreement also helps extend the life ofyour new appliance. Here's what's included in the Agreement:

    Expert service by our 12,000 professional repair special istsV Unlimited service and no charge for parts and labor on all

    covered repairsv" "No-lemon" guarantee - replacement of your coveredproduct if more than three product failures occur within twelvemonthsv"Product replacement if your covered product can't be fixedv" Annual Preventive Maintenance Check at your request- noextra chargev" Fast help by phone - non-technical and instructionalassistance on products repaired in your home, plus convenientrepair schedulingPower surge protection against electrical damage due topower fluctuations

    v" Rental reimbursement if repair of your covered producttakes longer than promisedOnce you purchase the Agreement, a simple phone call is all thatit takes for you to schedule service. You can call anytime day ornight, or schedule a service appointment onl ine.Sears has over 12,000 professional repair specialists, who haveaccess to over 4.5 million quality parts and accessories. That'sthe kind of professionalism you can count on to help prolong thelife of your new purchase for years to come. Purchase yourMaster Protection Agreement today!Some limitations and exclusions apply. For prices andinformation call 1-800-827-6655.Sears Installation ServiceFor Sears guaranteed professional installation of homeappliances and items like garage door openers and waterheaters, in the U.S.A. cal l 1-800-4-MY-HOME _.

    Your purchase has added value because you can depend onSears HomeCentral for service. With over 2,400 ServiceTechnicians and access to over 900,000 parts and accessories,we have the tools, parts, knowledge and skills to back ourpledge: We Service What We Sell.Sears Maintenance AgreementsYour Kenmore _ appl iance is designed, manufactured and testedto provide years of dependable operation. Yet any majorappliance may require service from time to time. The SearsMaintenance Agreement offers you an outstanding serviceprogram, affordably priced.The Sears Maintenance Agreement Guarantees tomorrow's service at today's price. Eliminates repair bills resulting from normal wear and tear. Covers non-technical and instructional service calls. Provides an annual Preventive Maintenance Check, at yourrequest, to ensure that your appliance is in proper runningcondition.Some limitations apply. For information concerning SearsHome Central": Maintenance Agreements, call1-800-361-6665.

    Replacement PartsTo order stainless steel cleaner or replacement filters, cal l1-800-4MY-HOME and ask for the appropriate part numberl isted below or contact your authorized Kenmore dealer.Stainless Steel Cleaner & Polish:Order Part #D22 M40083 RBase grille water filter cartridges:Cyst Cartridge:Order Part #9902 (WF-NLC250 and WF-LC400)

    22

  • 8/3/2019 Owner's Manual - Kenmore

    23/25

    WATER FILTERCERTIFICATIONSWater _nt Device

    Certif_ato Numbez98- 1366

    D+t_]n_t*_ Ko,mmbetL_,,1998

    Depart_mtofIkalthServicesWater Tx_tment DeviceCertificate Numb_

    98-1367Ds_ Bm_: Novlmmb_ IS+19:J8

    TrtdemlrldMedd D#h_ox_on R Iicemeat Eleme_tlvrnmpootcF-i.c4oo , i.c 4oo

    Mnnhetarm w_qp0o] _,

    Thewxtertrextlmentde_l i)lllt_donl_ll_ _t tJ!huyem e_t]te)e tddngr _t_t pu. rluat_em_Jo 11611_0 of ,be .e_+(lll ltnd S fe;_+_ (+" _,be 1+0LlIdl _ ] le_iL4:_ rd,it ee_ po lUl Letlm t I.

    Mkrobld letl _O_tlt_[D Dtl acid TlrbH 1 _ djOlO'_] COBtlt_[]_ll

    Rtt_d Serdee Ct_aei tT: 400

    Do no use where water it mlc robl ologXcxl l_ _tafe or wflh water of unknowu quarry, e_cept thais ys tems c la im ing cyst redleflon m_y be u|ed on w ater coat jlaing cysts.

    23

  • 8/3/2019 Owner's Manual - Kenmore

    24/25

    PRODUCT DATA SHEETSBase Grille Water Filtration System Model WF-NLC250/NLC250

    (_) Tested and certified by NSF International against ANSI/NSF Standard2 for the reduction of Chlorine (Class I) Taste and Odor and againstANS/NSF Standard 53 for the reduct on of Lead, Cysts and Turb d ty.Capacity; 250 Gal lons (946 Liters)Service Flow Rate: 0.5 GPM (1.89 L/min.) @ 60 psi.

    Substance Reduction U.S. EPA Average Maximum Average Minimum % Average % NSF TestAesthetic Effects MCL Influent Effluent Effluent Reduction Reduction NumberChlorine Taste/Odor N/A 1.9 mg/L N/A 0.04 mg/L N/A 97.9% 994707Particulate N/A 610,000/mL* N/A 154/mL N/A 99.97% 994711Contaminant U.S. EPA Average Maximum Average Minimum % Average % NSF TestReduction MCL Influent Effluent Effluent Reduction Reduction NumberCyst 99.95%** 89,250/mL* 6/mL 2.3/mL 99.993% 99.997% 994710Turbidity 0.5 NTU 29 NTU 0.1 NTU 0.09 NTU 99.5% 99.69% 994710Lead: @pH 65 0.015 mg/L 0.16 mg/L*** 0.001mg/L 0.001 mg/L 99.4% 99.4% 994708Lead: @pH 8.5 0.015 mg/L 0.16 rag/L*** 0.002 mg/L 0.001 mg/L 98.8% 99.4% 994709Base Grille Water Filtration System Model WF-LC400/LC400

    (_) Tested and certified by NSF International against ANSI/NSF Standard2 for the reduction of Chlorine (Class I) Taste and Odor and againstANS/NSF Standard 53 for the reduct on of Lead, Cysts and Turb d ty.Capacity; 400 Gallons (1514 Liters)Service Flow Rate: 0.5 GPM (1.89 L/min.) @ 60 psi.

    Substance Reduction U.S. EPA Average Maximum Average Minimum % Average % NSF TestAesthetic Effects MCL Influent Effluent Effluent Reduction Reduction NumberChlorine Taste/Odor N/A 2.0 mg/L N/A 0.04 mg/L N/A 98% 994707Particulate N/A 610,000/mL* N/A 154/mL N/A 99% 994711Contaminant U.S. EPA Average Maximum Average Minimum % Average % NSF TestReduction MCL Influent Effluent Effluent Reduction Reduction NumberCyst 99.95%** 89,250/mL* 6/mL 2.3/mL 99.993% 99.997% 994710Turbidity 0.5 NTU 29 NTU 0.12 NTU 0.09 NTU 99.59% 99.69% 994710Lead: @pH 65 0.015 mg/L 0.16 mg/L*** 0.001mg/L 0.001 mg/L 99.4% 99.4% 994708Lead: @pH 8.5 0.015 mg/L 0.16 rag/L*** 0.002 mg/L 0.001 mg/L 98.8% 99.4% 994709 It is essential that operational, maintenance, and filterreplacement requirements be carried out for the product toperform as advertised. Model WF-NLC250 Change cartridge at least every 6-9months. Use replacement cartridge NLC 250, part# 9902.2002 suggested retail price of $39.95 U.S.A./S49.95 Canada.Prices are subject to change without notice. Model WF-LC400 The filter monitor system measures theamount of water that passes through the filter and alerts youto replace the filter. When 90% of the filter's rated life is used,the filter indicator light changes from green to yellow. When

    100% of the filter's rated life is used, the filter indicator lightchanges from yellow to red, and it is recommended that youreplace the fi lter. Use replacement cartridge LC400,part# 9902. 2002 suggested retail price of $39.95 U.S.A./$49.95 Canada. Prices are subject to change without notice. The product is for cold water use only. Do not use with water that is microbiologically unsafe or ofunknown quality without adequate disinfection before or a_erthe system.

    Refer to the front cover or "Assistance or Service" section forthe Manufacturer's name, address and telephone number.

    Refer to the "Warranty" section for the Manufacturer's limitedwarranty.Application Guidelines/Water Supply Parameters

    Water Supply City or WellWater Pressure 30 - 120 psi (207 - 827 kPa)

    * Test requirement is at least t00,000 particles/ml of AC Fine Test Dust.** Cyst performance is % reduction based on NSF Standard 53.

    *** Test requirement is 0.15 mg/L 10%. These contaminants are not necessarily in your water supply. Performance may vary based on local waterconditions. NSF is a registered trademark of NSF International24

  • 8/3/2019 Owner's Manual - Kenmore

    25/25

    Your HomeFor repair-in your home-of all major brand appliances,lawn and garden equipment, or heating and cooling systems,no matter who made it, no matter who sold it!

    For the replacement parts, accessories andowner's manuals that you need to do-it-yourself.For Sears professional installationof home appliancesand items like garage door openers and water heaters.

    1-800-4-MY-HOME (1-soo-469-4ss3)Call anytime, day or night (U.S.A. and Canada)www.sears.com www.sears.ca

    Our HomeFor repair of carry-in items like vacuums, lawn equipment,and electronics, call or go on-line for the location of your nearest

    Sears Parts & Repair Center,1-800-488-1222

    Call anytime, day or night (U.S.A. only)www.sears.com

    To purchase a protection agreement ona product servicedby Sears:1-800-827-6655 (U,S,A,) 1-800-361-6665 (Canada)

    Para pedir serviciode reparaci6na domicilio,y para ordenarpiezas:1-888-SU-HOGAR _

    (1-888-784-6427)

    Au Canada pour service en fran_ais:1-800-LE-FOYER Mc(1-800-533-6937)www.sears.caSEARS

    TM M5/02