OWN000204 BSC6800 System Commissioning ISSUE3.0

7/29/2019 OWN000204 BSC6800 System Commissioning ISSUE3.0

1/40

BSC6800 System Commissioning


2/40

Review

BSC6800 system commissioning includes loading

commissioning, License commissioning, and

interface and service commissioning that

ultimately bring the system into normal operation

after the hardware installation and software

installation .


3/40

Objectives

Master the loading commissioning,

License commissioning, and interfaceand service commissioning .

Upon completion of this course,you will be able to:


4/40

References

31041209-BSC6800 Installation Manual - System

Commissioning (V1.20)


5/40

Course Contents

Overview

Loading Commissioning

Feature Commissioning

Interface and Service Commissioning


6/40

Prerequisite

Preparing Delivery-Attached Manuals

Checking Hardware

Checking Software

Checking Network

Checking Configuration Data

Checking Peer Equipment


7/40

Prerequisite

Hardware Installation check

Hardware installation check

DIP switch and jumper check


8/40

Prerequisite

Software Installation check

Object No. Item Result Remark

Operating

system

1 Windows 2000

Server?

Y [ ] N [ ] If no, install the operating system according to Appendix

A in Huawei BSC6800 WCDMA Radio Network

Controller Installation ManualSoftware Installation.

2 SP4 patch installed? Y [ ] N [ ] If no, install/upgrade the patch according to Appendix A

in Huawei BSC6800 WCDMA Radio Network Controller

Installation Manual

Software Installation.

SQL Server 3 SQL Server 2000

Standard Version?

Y [ ] N [ ] If no, install the SQL Server according to Appendix A in

Huawei BSC6800 WCDMA Radio Network Controller

Installation ManualSoftware Installation.

4 SP3 patch installed? Y [ ] N [ ] If no, install/upgrading the patch according to Appendix A



5 SQL Server started? Y [ ] N [ ]

BAM software 6 BAM version right? Y [ ] N [ ]

7 BAM Server started? Y [ ] N [ ]

8 Files to be loaded in

specified directory?

Y [ ] N [ ]

LMT software 9 LMT version right? Y [ ] N [ ]


9/40

Prerequisite

Network Communication check

Object No. Item Result Remark

Network

configuration

of BAM

Server

1 Network adapters

teamed?

Y [ ] N [ ] If no, team the network adapters according to Appendix A



2 IP setting right? Y [ ] N [ ]

Networkconfiguration

of LMT

computer

3 IP setting right? Y [ ] N [ ]

Internal

network

4 BAM and WMPU in

normal

communication?

Y [ ] N [ ]

External

network

5 LMT and BAM in

normal

communication?

Y [ ] N [ ]


10/40

Procedure

system commissioning procedure

Start

Loading

commissioning

Feature

commissioning

Interface and service

verifying

End


11/40

Course Contents

Overview





12/40

Introduction

loading commissioning procedure

Start

Generatedata

f iles

LoadFAM

sof tware

End

Setloadingchannel

Checkloading


13/40

Introduction

FAM software loading channel

Program files

Data files

WMPU

Boards in WRBS

WMUX/WSPU

BAM

WRSS

WRBS

Other boards in WRSS


14/40

Setting Loading Channel

The loading channel is a LMT-BAM-WRSS-WRBS channel

Setting BAM-WRSS Channel

Carry out SET WMPUIP to set the external IP address of the

WMPU

Setting Routes for BAM (default)

Route No. Network address Netmask Gateway address Interface Metric

1 80.0.0.0 255.0.0.0 10.121.A.C 10.121.A.B 1

2 192.1.0.0 255.255.0.0 10.121.A.C 10.121.A.B 1


15/40

Generating Data Files

The program files have come into being in the BAM Server

since BAM software installation. You need generate the data

files for loading

You may prepare a Man Machine Language (MML) script of

the configuration data (data script) and then generate datafiles from the script for loading in offline mode

checking Data script

Data Script Execution

Carry out FMT DATA to generate the data files for loading


16/40


Host software of the WRSS

BoardHost software

WMPU MPUB.VFS

WNET NETB.VFS, CLKC_LOG.VFS

WLPU LPUBGFI.VFS

WHPU WHPU750.VFS, WHPU1200.VFS, WHPULOGC.VFS, WHPUWC.VFS


17/40


Data file of the WRSS

The data file to be loaded to the WRSS is BNET.dat. When you

prepare a load data file, BNET.dat will be created and saved in

the new folder Config under the directory LoadDATA

To load a data file to the WRSS is right to load BNET.dat to the

WMPU


18/40


Host software of the WRBS

BoardHost software

WMUX B00MUX0.bin

WSPU B00SPU0.bin

WSPUb B00EPU0.bin

WFMR B00FMR0.bin, B00FMR0.dsp

WXIE B00XIE0.bin

WOSE/WOME B00OIE0.bin

WBIE/WTIE B00BIE0.bin


19/40


Data file of the WRBS

The data file of the BSC6800 system is stored as ".dat" file in

the BAM server, When receiving a data load request from a

board subsystem, the server will load the corresponding data file

to the subsystem

Such data files include the configuration data that will be stored

on the WMUX or on the WSPU

The file name of the data file is in the format of HXYABCN.dat


20/40

Loading FAM Software

Setting Loading Mode of Program File

Carry out SET LODPARA . Select "WRSS or "WRBS" for

[Subrack Type] and "FLWF (FORCEDLY LOAD AND WRITE

FLASH)" for [Host code load control]

The program files will be loaded from the BAM Server and

written to the Flash Memory of the corresponding boards when

the boards start or reset.


21/40

Checking Loading

Checking Board State

On the equipment panel

Through an MML command: DSP BRD

The BSC6800 contains two sets of configuration parameters

that respectively exist in FAM and BAM. They are both intables

Carry out ACT CRC to check the data consistency on table level

Carry out CMP TBLDATA to check the data consistency on

record level

Check that the cell setup procedure, common channel setup

procedure and measurement messages are all normal

through the message tracing on a LMT


22/40

Course Contents

Overview





23/40

Introduction

Function of License file

No. Feature Description

1 Max. number of users Max. number of users allowed in the BSC6800

2 Inter-RAT handover out-going switch Inter-RAT handover between GSM and WCDMA (from UMTS to GSM)

3 Inter-RAT handover in-coming switch Inter-RAT handover between GSM and WCDMA (from GSM to UMTS)

4 PDCP header compression functionThe BSC6800 can perform PDCP header compression to increase the

connection rate.

5 Cell ID LCS Location services based on Cell ID

6 OTDOA LCS Location services based on OTDOA

7 A_GPS LCS Location services based on A_GPS

8 Load optimizationThe following optimization means are provided, that is, cell breathing,

load handover and potential user control.

9 AMR controlThe BSC6800 can control the AMR encoding rate to provide the best

speech quality, increase inverse cell coverage and reduce system load.


24/40

Introduction

Function of License file

10 TFO/TrFO

TFO: Speech information is not coded using code converter if UEs in

a mobile-to-mobile call support the same code type as the network.

TrFO: The BSC6800 involved in a mobile-to-mobile call supports

speeches or multimedia services in TrFO mode.

11Dynamic channel configuration

control

Bandwidth resources can be allocated flexibly to satisfy the

requirements of burst PS services. The services can be handed over

between dedicated and common channels so that the resources can

be fully utilized.

12 Direct retry

On setup of an Radio Resource Control(RRC) connection, the

BSC6800 can specify a cell for the User Equipment(UE) to access

according to the resource status to increase the access success rate.

13 Call traceMessage trace and interpretation on standard Iub, Iur, Iu and Uu

interfaces, single subscriber trace and cell trace

14 Cell Broadcast Service(CBS) Cell broadcast service


25/40

Introduction

Commissioning Procedure

Start

Import License file

Activate License

file

Set algorithm

switch of feature

End

Feature controlled

by algorithm switch?

N

Y


26/40

Importing License File

Import a correct License file as prompted during BAM installation

Otherwise, copy the License file to the following directory:

BAM installation directory\LICENSE

BAM installation directory\FTP\LICENSE


27/40

Activating License File

Activating License File with Reconfiguration of RNC ID and PLMN

ID Carry out SET OFFLINE to switch to the offline mode, and then

reconfigure the RNC ID and PLMN ID accordingly

If the BSC6800 has no basic information, carry out ADD RNCBASIC to

add the RNC ID and PLMN ID

If the basic information of the BSC6800 is not authorized in the License file,

carry out MOD RNCBASIC to modify the RNC ID and PLMN ID as those

presented in the License file

Carry out ACT LICENSE to activate license file. BAM will check

validity of the file. If valid, the file will be written into the memory of

BAM

To activate the License function in the FAM, carry out RST SYS to

reset the BSC6800 system


28/40

Activating License File

Activating License File without Reconfiguration of RNC ID and

PLMN ID

Carry out SET ONLINE to switch to the online mode

Carry out ACT LICENSE to activate license file. BAM will check

validity of the file. If valid, the file will be written into the memory ofBAM


29/40

Setting Algorithm Switch of Feature

Carry out SET CORRMALGOSWITCH to set an algorithm switch

You may set the following classes of algorithm switches using the

command:

Channel class algorithm switch

Handover algorithm switch

Power control algorithm switch

Traffic combination switch


30/40

Course Contents

Overview





31/40

Introduction

You need also perform commissioning for interface data and dial-tests for system services before you put the BSC6800 into normal

service


32/40

Iub Interface Commissioning

Physical Link Commissioning

Local loop

Set the loopback type of a test E1/T1 link as LOCAL on a LMT using:

SET E1T1LOP if the E1/T1 link is on an E1/T1 trunk

SET SDHLOP if the E1/T1 link is on an SDH

Carry out LOP E1T1 on the LMT to initiate a local loopback test for theE1/T1 link

Set the loopback type of the test E1/T1 link as NOLOOP on the LMT

When performing a loopback test for an E1/T1 link in an IMA group, be

sure to carry out RST IMAGRP to reset the IMA group after the loopback

test


33/40


Physical Link Commissioning

Combined loop

Set the loopback type of a test E1/T1 link as REMOTE in the operation and

maintenance system at the peer end

Carry out LOP E1T1 on a LMT to initiate a combined loopback test for the

E1/T1 link.


34/40


Control Plane Commissioning

Carry out DSP SAALLNK to check that all Signaling ATM Adaptation

Layer (SAAL) links are available

Carry out DSP IUBP to check that the NCP link and all CCP links are

available

Carry out DSP AAL2ADJNODE to check that the adjacent node of

NodeB is available


35/40


User Plane Commissioning

Carry out DSP AAL2PATH to check that the AAL2 path(s) to a

specified adjacent node is/are functional


36/40

Iu Interface Commissioning

Physical Link Commissioning Control Plane Commissioning

Carry out DSP SAALLNK to check that all SAAL links are available.

Carry out DSP MTP3BLNK to check that all MTP3b links are available.

Carry out DSP SSN to check that all SCCP subsystems are available.

Carry out DSP AAL2ADJNODE to check that the adjacent node of

MSC is available.

User Plane Commissioning


37/40

Iur Interface Commissioning

The commissioning of an Iur interface is similar to that of an Iuinterface.

You need also check that the IP routes of the BSC6800 to other

Radio Network Controllers (RNCs) are available for supporting

lossless relocation. Carry out PNG IPADDR on a LMT to check theconnectivity of an IPoA to another RNC


38/40

Service Commissioning

Dial-tests for basic services

Basic service Dial-test method Expected results

Voice service

Make fifty calls from a UE to a fixed

network phone. Make fifty calls from the

network phone to the UE.

The connection success rate is above 90%. The

calls sound clear. There is no loud noise in the

calls.

Make fifty calls from a UE to another UE.



calls.

CS streaming

service

Send a fax from a UE to the PSTN. Send a

fax from the Public Switched Telephone

Network(PSTN) to the UE.

The UE sends and receives the faxes normally.

Send a video service from a UE to another

UE

The audio part sounds clear. The visual part is

continuous. The two parts are synchronous.

PS service

Activate 384-kbit/s and 144-kbit/s services,

visit World Wide Web(WWW) Server and

browse pages on a UE fifty times.

The activation success is above 90%. The

browsing is successful.

Activate 384-kbit/s and 144-kbit/s servicesand perform download some data using

FLASHGET on a UE for half an hour.

The download is not intermittent. The average

download rate reaches 300 kbit/s or above.

Mobility

management

Perform CS voice service handover fifty

times.The handover success rate is above 95%.

Perform PS service handover fifty times. The handover success rate is above 95%.

Operation and

maintenancemanagement

Perform switchover for the WMPUs,

WMUXs and WSPU/WSPUbs fifty timesduring service

The switchover success rate is above 90%. There

is no service interruption in the switchoverprocedures.


39/40

Service Commissioning

Dial-tests for features

Feature Dial-test method Expected results

Inter-RAT

handover

Hand over a dual-mode UE from UMTS to

GSM and back fifty times.



calls.


40/40

Documents

OWN000204 BSC6800 System Commissioning ISSUE3.0