OVERALL SITE PLAN...530.520.0512 DESIGNS STAR CONTRACTING 2ND FLR. POWER PLAN LIGHTING / REFLECTED...
5
530.520.0512 DESIGNS STAR CONTRACTING OVERALL SITE PLAN RED LION APTS. - 6100 WATERS AVE. A PROPOSED PRIVATE OWNER'S RESIDENCE CONVERSION
OVERALL SITE PLAN...530.520.0512 DESIGNS STAR CONTRACTING 2ND FLR. POWER PLAN LIGHTING / REFLECTED CLG. PLAN S.D. S.D. S.D. S.D. W.P. W.P. EXHST. FAN S T S S EXHST. FAN S T S S S M
ALL WORK TO BE IN ACCORDANCE WITH ALL STATE AND LOCAL CODES AND REQUIREMENTS.
AutoCAD SHX Text
LOCATE ALL RECEPTACLES PER NEC SECTION 210.52.
AutoCAD SHX Text
LOCATE ALL OUTDOOR & WET AREA RECEPTACLES (GFCI) PER NEC SECTION 210.8.
AutoCAD SHX Text
FIXTURES LOCATED OUTDOORS OR IN WET AREAS (SHOWERS) TO COMPLY WITH NEC SECTION 210.52(E) & 406.9(B)(1).
AutoCAD SHX Text
FIXTURES LOCATED IN CLOSETS TO COMPLY WITH NEC SECTION 410.16(A)
AutoCAD SHX Text
VERIFY EXACT LOCATIONS OF PHONE, DATA AND CABLE JACKS WITH OWNER AT ROUGH-IN.
AutoCAD SHX Text
PROVIDE 125V RECEPTACLE NEAR HVAC EQUIPMENT PER NEC 210.63
AutoCAD SHX Text
LOCATE HVAC RECEPTACLES & DISCONNECTS PER NEC ARTICLE 440.
AutoCAD SHX Text
VENT ALL EXHAUST FANS & HOODS TO OUTSIDE AIR (O.S.A.). TERMINATE 3' (MIN.) FROM ALL OPENINGS INTO STRUCTURE.
AutoCAD SHX Text
PRE-WIRE ALL DOORS AND WINDOWS FOR SECURITY ALARM SYSTEM.
AutoCAD SHX Text
ALL MECHANICAL EQUIPMENT TO MAINTAIN MANUF. RECOMMENDATIONS FOR CLEARANCES.
AutoCAD SHX Text
PROVIDE SEPARATE CABLE SYSTEMS FOR PHONE, AUDIO / VIDEO AND COMPUTER INSTALLATIONS.
AutoCAD SHX Text
ALL CIRCUITS SUPPLYING 15 AND 20 AMP BEDROOM OUTLETS ARE TO BE PROTECTED BY ARC-FAULT CIRCUIT INTERRUPTERS.
AutoCAD SHX Text
SYSTEM TO BE MULTI-ZONE SPLIT SYSTEM CONSISTING OF (1) ELECTRIC CONDENSER UNIT AND (1) INTERIOR FURNACE/AIR-HANDLER UNIT LOCATED WHERE SHOWN ON PLANS. EXTERIOR UNIT MOUNTED ON SLAB.
AutoCAD SHX Text
HVAC EQUIPMENT TO BE SIZED BY MECHANICAL CONTRACTOR IN COMPLIANCE WITH ALL STATE AND LOCAL CODES.
AutoCAD SHX Text
S.D.
AutoCAD SHX Text
ALL ELECTRICAL RECEPTACLES TO BE TAMPER RESISTANT PER NEC SECTION 406.12
AutoCAD SHX Text
14.
AutoCAD SHX Text
ALL FAMILY ROOMS, LIVING ROOMS, BEDROOMS, CLOSETS, HALLWAYS, AND SIMILAR ROOMS/SPACES SHALL HAVE ARC-FAULT CIRCUIT INTERRUPTERS (AFCI). PER NEC SECTION 210.12(A)
AutoCAD SHX Text
15.
AutoCAD SHX Text
PROVIDE A MINIMUM OF TWO (2) 20 AMP DEDICATED BRANCH CIRCUITS FOR THE KITCHEN/DINING ROOM. NEC SECTION 210.11(C)(1)
AutoCAD SHX Text
16.
AutoCAD SHX Text
PROVIDE ONE (1) 20 AMP DEDICATED BRANCH CIRCUIT TO SUPPLY THE LAUNDRY RECEPTACLE OUTLET(S). THIS CIRCUIT SHALL HAVE NO OTHER OUTLETS PER NEC SECTION 210.52(F)
AutoCAD SHX Text
17.
AutoCAD SHX Text
AUTOMATIC LIGHTING CONTROL - ROOM VACANCY SENSOR
AutoCAD SHX Text
VS
AutoCAD SHX Text
1606 Staley Ave Savannah, GA 31405 (912) 236-2919
AutoCAD SHX Text
Scale
AutoCAD SHX Text
Job No.
AutoCAD SHX Text
SHEET No.
AutoCAD SHX Text
Checked By
AutoCAD SHX Text
Date Drawn
AutoCAD SHX Text
Drawn By
AutoCAD SHX Text
Description
AutoCAD SHX Text
Sym.
AutoCAD SHX Text
REVISIONS
AutoCAD SHX Text
By
AutoCAD SHX Text
DRAWING STATUS
AutoCAD SHX Text
SHEET TITLE
AutoCAD SHX Text
PROJECT NAME
AutoCAD SHX Text
Date
AutoCAD SHX Text
Copyright
AutoCAD SHX Text
C
AutoCAD SHX Text
POWER / LIGHTING
AutoCAD SHX Text
REFLECTED CLG. PLAN
AutoCAD SHX Text
DAR
AutoCAD SHX Text
.
AutoCAD SHX Text
1/4"=1'-0"
AutoCAD SHX Text
A3
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
SCALE: 1/4" = 1'-0"
AutoCAD SHX Text
+9'-6"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+10'-6"
AutoCAD SHX Text
+10'-6"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+8'-6"
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
EXP.
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
1
AutoCAD SHX Text
-
AutoCAD SHX Text
NEW SOFFIT FRAMING
AutoCAD SHX Text
1
AutoCAD SHX Text
SCALE: 1"=1'-0"
AutoCAD SHX Text
RETURN AIR
AutoCAD SHX Text
GRILL
AutoCAD SHX Text
EXISTING SUSPENDED ACOUSTICAL CEILING TO BE REPLACED WITH FRAMED GYP. BD. CEILING.
AutoCAD SHX Text
+8'-6"
AutoCAD SHX Text
+8'-6"
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+9'-6"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+8'-6"
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
A PROPOSED
AutoCAD SHX Text
PRIVATE OWNER'S
AutoCAD SHX Text
RESIDENCE
AutoCAD SHX Text
RED LION
AutoCAD SHX Text
APARTMENTS
AutoCAD SHX Text
AT THE
AutoCAD SHX Text
.
AutoCAD SHX Text
6100 WATERS AVE.
AutoCAD SHX Text
SAVANNAH, GA
AutoCAD SHX Text
CD SET
AutoCAD SHX Text
PERMIT SUBMITTAL
AutoCAD SHX Text
12/26/17
AutoCAD SHX Text
12-1012
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
SCALE: 1/4" = 1'-0"
AutoCAD SHX Text
FURNITURE SHOWN FOR REFERENCE ONLY
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+8'-0"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+8'-3"
AutoCAD SHX Text
+9'-0"
AutoCAD SHX Text
+8'-0"
AutoCAD SHX Text
NEW 10" DIA. SKYLIGHT TUBES TO BE VELUX 'SUN TUNNEL' W/ RIGID SHAFT, CURB MOUNT TCR KIT AND FROSTED DIFFUSER
DETAILS
A4
CD SET
PERMIT SUBMITTAL
530.520.0512
DESIGNS
STAR CONTRACTING
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
TOILET ROOM IDENTIFICATION SIGNAGE
AutoCAD SHX Text
7
AutoCAD SHX Text
NONE
AutoCAD SHX Text
A4
AutoCAD SHX Text
WOMEN
AutoCAD SHX Text
6" GENDER SYMBOL, TYP.
AutoCAD SHX Text
TACTILE SIGNAGE - COMPLY WITH A.D.A. 703 (LOCATE ON WALL ADJACENT TO DOOR LATCH) LETTERS AND NUMERALS SHALL BE RAISED 1/32", UPPER CASE, SANS SERIF TYPE MEASURING BETWEEN 5/8" AND 2" HIGH WITH BRAILLE LOCATED 3/8" - 1/2" DIRECTLY BELOW TEXT.
AutoCAD SHX Text
BRAILLE - COMPLY WITH A.D.A. 703.2 AND 703.3 GRADE II, DOTS =1/10" ON CENTER IN EACH CELL WITH 2/10" SPACE BETWEEN CELLS, RAISED 1/40".
AutoCAD SHX Text
OBSTRUCTIONS: A PERSON MUST BE ABLE TO APPROACH WITHIN 3" OF SIGNAGE WITHOUT ENCOUNTERING PROTRUDING OBJECTS OR STANDING (SITTING) WITHIN SWING OF DOOR.
AutoCAD SHX Text
6" LOGO INTERNATIONAL SYMBOL OF ACCESS
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
TACTILE EXIT DOOR SIGNAGE
AutoCAD SHX Text
4
AutoCAD SHX Text
NONE
AutoCAD SHX Text
A4
AutoCAD SHX Text
(FACILITY
AutoCAD SHX Text
NAME / LOGO)
AutoCAD SHX Text
EXIT
AutoCAD SHX Text
(FACILITY
AutoCAD SHX Text
NAME / LOGO)
AutoCAD SHX Text
(FACILITY
AutoCAD SHX Text
NAME / LOGO)
AutoCAD SHX Text
EXIT
AutoCAD SHX Text
EXIT AT GRADE-LEVEL EXTERIOR DOOR
AutoCAD SHX Text
DIRECTIONAL SIGN LEADING TO EXIT MOUNTED IN HALLWAY, NOT AT EXIT DOOR
AutoCAD SHX Text
EXIT
AutoCAD SHX Text
TACTILE & BRAILLE EXIT SIGNAGE ALL UPPER CASE, SANS SERIF TEXT 5/8" - 2" HEIGHT, RAISED 1/32" CONTRACTED GRADE 2 BRAILLE - COMPLY WITH A.D.A. 703.3
AutoCAD SHX Text
ILLUMINATED EXIT SIGN WHERE REQUIRED - SEE 5/A005, REFLECTED CEILING PLAN AND ELEC'L DWGS.
AutoCAD SHX Text
NOTES: 1.RAISED CHARACTERS SHALL BE 60" MAX. A.F.F. RAISED CHARACTERS SHALL BE 60" MAX. A.F.F. MEASURED FROM THE BASELINE OF THE HIGHEST LINE OF RAISED CHARACTERS. BRAILLE SHALL BE 48" MIN. A.F.F. MEASURED FROM THE BASELINE OF THE LOWEST LINE OF BRAILLE. MOUNT AT STRIKE SIDE OF DOOR.
AutoCAD SHX Text
2.SIGN TEXT TO BE A 70% CONTRASTING COLOR TO SIGN FIELD. SIGN TEXT TO BE A 70% CONTRASTING COLOR TO SIGN FIELD. 3.SIGN TO COMPLY WITH A.D.A. 608 AND I.B.C. SEC. 1011.3 SIGN TO COMPLY WITH A.D.A. 608 AND I.B.C. SEC. 1011.3 4.ACTUAL SIGN DESIGN AND DIMENSIONS SHALL BE BY PROVIDED BY DESIGN / ACTUAL SIGN DESIGN AND DIMENSIONS SHALL BE BY PROVIDED BY DESIGN / BUILD SIGNAGE CONTRACTOR IN COORDINATION WITH OWNER AND CONTRACTOR. 5.OBSTACLES: A PERSON MUST BE ABLE TO APPROACH WITHIN 3" OF SIGNAGE OBSTACLES: A PERSON MUST BE ABLE TO APPROACH WITHIN 3" OF SIGNAGE WITHOUT ENCOUNTERING PROTUDING OBJECTS OR STANDING (SITTING) WITHIN SWING OF DOOR.
AutoCAD SHX Text
EXIT ROUTE
AutoCAD SHX Text
EXIT FROM AN INTERIOR ROOM BY MEANS OF AN EXIT ACCESS CORRIDOR
AutoCAD SHX Text
NOTE: PROVIDE PROVIDE BLANK SIGN ON OPPOSITE SIDE OF GLASS TO COVER SIGN MOUNTING WHEN SIGN IS MOUNTED TO SIDELIGHT OR WINDOW
AutoCAD SHX Text
1.ALL DIMENSIONS ARE CLEAR DIMENSIONS FROM EDGE OF FIXTURE OR FACE OF FINISH ALL DIMENSIONS ARE CLEAR DIMENSIONS FROM EDGE OF FIXTURE OR FACE OF FINISH 2.GENERAL CONTRACTOR TO PROVIDE STRUCTURAL SUPPORT AND/OR METAL REINFORCEMENT IN GENERAL CONTRACTOR TO PROVIDE STRUCTURAL SUPPORT AND/OR METAL REINFORCEMENT IN STUD WALLS AT ALL CASEWORK, CABINETS, SHELVING, EQUIPMENT ETC. REFER TO 8 & 12 ON A902 FOR TYPICAL BACKING REQUIREMENTS. 3.TOILET ACCESSORIES SHALL NOT PROJECT INTO CLEAR SPACES. TOILET ACCESSORIES SHALL NOT PROJECT INTO CLEAR SPACES. 4.DISPENSERS SHALL NOT PROJECT MORE THAN 4" FROM FACE OF WALL.DISPENSERS SHALL NOT PROJECT MORE THAN 4" FROM FACE OF WALL.
AutoCAD SHX Text
PLAN
AutoCAD SHX Text
15"
AutoCAD SHX Text
15"
AutoCAD SHX Text
15"
AutoCAD SHX Text
42" MIN., 1-1/2" DIA. GRAB BAR
AutoCAD SHX Text
36" MIN., 1-1/2" DIA. GRAB BAR
AutoCAD SHX Text
F.O. WALL OR PARTITION, WHERE OCCURS
AutoCAD SHX Text
1-1/2" SPACE BETWEEN FACE OF WALL & FACE OF BAR
AutoCAD SHX Text
48" GRAB BAR
AutoCAD SHX Text
17"
AutoCAD SHX Text
17"
AutoCAD SHX Text
17"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
F.O. COUNTER TOP
AutoCAD SHX Text
MIRROR
AutoCAD SHX Text
27"
AutoCAD SHX Text
27"
AutoCAD SHX Text
27"
AutoCAD SHX Text
9"
AutoCAD SHX Text
9"
AutoCAD SHX Text
9"
AutoCAD SHX Text
KNEE SPACE
AutoCAD SHX Text
LEVER OPERATING PUSH TYPE OR ELECTRONICALLY CONTROLLED
AutoCAD SHX Text
S.D. W/ HIGHEST OPERABLE PART AT 40" A.F.F.
AutoCAD SHX Text
MIRROR
AutoCAD SHX Text
PIPE INSULATION AT HOT WATER & DRAW
AutoCAD SHX Text
FACE OF WALL WHERE OCCURS
AutoCAD SHX Text
FACE OF WALL
AutoCAD SHX Text
TOP OF FIN. FLOOR
AutoCAD SHX Text
WATER CLOSET
AutoCAD SHX Text
24"
AutoCAD SHX Text
24"
AutoCAD SHX Text
24"
AutoCAD SHX Text
F.O. TILE
AutoCAD SHX Text
2'-0"
AutoCAD SHX Text
2'-0"
AutoCAD SHX Text
2'-0"
AutoCAD SHX Text
2'-0"
AutoCAD SHX Text
2'-0"
AutoCAD SHX Text
FLUSH VALVE CONTROL ON OPEN SIDE
AutoCAD SHX Text
T.P.D.
AutoCAD SHX Text
F.O. TILE
AutoCAD SHX Text
17"
AutoCAD SHX Text
17"
AutoCAD SHX Text
17"
AutoCAD SHX Text
18"
AutoCAD SHX Text
18"
AutoCAD SHX Text
18"
AutoCAD SHX Text
30" X 48" CLR. FLOOR. SPACE; DOOR CAN'T SWING INTO REQ'D. CLEAR SPACE IN MULTI-FIXTURE TOILETS
AutoCAD SHX Text
T.P.D.
AutoCAD SHX Text
LAVATORY
AutoCAD SHX Text
WATER CLOSET
AutoCAD SHX Text
NOTE: TOILET PAPER & FEMININE NAPKIN DISPENSERS LOCATED ON THE GRAB BAR SIDE OF AN ACCESSIBLE TOILET ROOM OR STALL SHALL NOT PROJECT MORE THAN 3" FROM THE FINISHED WALL SURFACE NOR BE LOCATED CLOSER THAN 1-1/2" CLEAR OF THE TANGENT POINT OF THE GRAB BAR.
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
1'-6"
AutoCAD SHX Text
PLAN
AutoCAD SHX Text
ELEVATION
AutoCAD SHX Text
SECTION
AutoCAD SHX Text
FRONT ELEV
AutoCAD SHX Text
SIDE ELEV
AutoCAD SHX Text
%%130
AutoCAD SHX Text
%%130
AutoCAD SHX Text
%%130
AutoCAD SHX Text
%%130
AutoCAD SHX Text
BLOCKING
AutoCAD SHX Text
BLOCKING SEE
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
TOILET ROOM ACCESSORIES HEIGHTS & CLEARANCES
AutoCAD SHX Text
11
AutoCAD SHX Text
1/4" = 1'-0"
AutoCAD SHX Text
A4
AutoCAD SHX Text
BABY CHANGING STATION
AutoCAD SHX Text
TOILET PAPER DISPENSER
AutoCAD SHX Text
PARTITIONS
AutoCAD SHX Text
SOAP DISPENSER (SURFACE)
AutoCAD SHX Text
FOR ACCESSIBLE TOILETS, PROVIDE FLIP-OVER, SLIDING OR OTHER TYPE OF LATCH THAT DOES NOT REQUIRE THE USER TO GRASP OR TWIST. ACCESSIBLE DOOR WITH PULLS ON BOTH SIDES. ALL TOILET PARTITION DOORS TO BE OPERABLE WITHOUT SPECIAL TOOLS OR KEY.
ALL OTHER ACCESSORIES NOT TO PROJECT MORE THAN 4" FROM THE FINISHED WALL SURFACE WHEN LOCATED ALONG THE PATH OF TRAVEL.
AutoCAD SHX Text
SEE
AutoCAD SHX Text
SEE
AutoCAD SHX Text
7.
AutoCAD SHX Text
6.
AutoCAD SHX Text
5.
AutoCAD SHX Text
GRAB BARS:
AutoCAD SHX Text
A.
AutoCAD SHX Text
B.
AutoCAD SHX Text
C.
AutoCAD SHX Text
D.
AutoCAD SHX Text
A.
AutoCAD SHX Text
A.
AutoCAD SHX Text
B.
AutoCAD SHX Text
GRAB BARS, FASTENERS AND MOUNTING DEVICES SHALL BE DESIGNED FOR 250 POUNDS PER LINEAL FOOT LOAD.
AutoCAD SHX Text
GRAB BARS AND ANY WALL OR OTHER SURFACE ADJACENT TO IT SHALL BE FREE OF ANY SHARP OR ABRASIVE ELEMENTS.
AutoCAD SHX Text
GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS.
AutoCAD SHX Text
EDGES SHALL HAVE A MINIMUM RADIUS OF 1/8 INCH.
AutoCAD SHX Text
THRESHOLD:
AutoCAD SHX Text
WHEN A THRESHOLD OR RECESSED DROP IS USED, IT SHALL BE A MAXIMUM OF 1/2 INCH IN HEIGHT AND SHALL BE BEVELED OR SLOPED AT AN ANGLE NOT EXCEEDING 45 DEGREES FROM THE HORIZONTAL.
AutoCAD SHX Text
MISCELLANEOUS REQUIREMENTS:
AutoCAD SHX Text
THE TOTAL GRIPPING SURFACE OF THE OPERATING HANDLE OF SWITCHES INTENDED TO BE USED BY THE OCCUPANT OF THE ROOM OR AREA TO CONTROL LIGHTING AND RECEPTACLE OUTLETS, APPLIANCES, OR COOLING, HEATING AND VENTILATING EQUIPMENT SHALL BE NOT LESS THAN 3 FEET NOR MORE THAN 4 FEET ABOVE THE FLOOR
AutoCAD SHX Text
THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE THE STANDARD USED TO IDENTIFY FACILITIES THAT ARE ACCESSIBLE TO AND USABLE BY PHYSICALLY DISABLED PERSONS. THE SYMBOL SHALL CONSIST OF A WHITE FIGURE ON A BLUE BACKGROUND. THE BLUE SHALL BE EQUAL TO COLOR NR. 15090 IN FEDERAL STANDARD 595A.
AutoCAD SHX Text
8
AutoCAD SHX Text
A4
AutoCAD SHX Text
ACCESSIBILITY NOTES
AutoCAD SHX Text
URINAL
AutoCAD SHX Text
TOP OF FIN. FLOOR
AutoCAD SHX Text
17" MAX. TO FACE OF RIM
AutoCAD SHX Text
2'-6"
AutoCAD SHX Text
2'-6"
AutoCAD SHX Text
2'-6"
AutoCAD SHX Text
2'-6"
AutoCAD SHX Text
30"x48" CLEAR FLOOR SPACE
AutoCAD SHX Text
PLAN
AutoCAD SHX Text
FRONT ELEVATION
AutoCAD SHX Text
%%130
AutoCAD SHX Text
%%130
AutoCAD SHX Text
2
AutoCAD SHX Text
-
AutoCAD SHX Text
5
AutoCAD SHX Text
-
AutoCAD SHX Text
BLOCKING AS REQ'D
AutoCAD SHX Text
5
AutoCAD SHX Text
-
AutoCAD SHX Text
TOWEL DISPENSER WHERE UNOBSTRUCTED
AutoCAD SHX Text
ROOM IDENTIFICATION AT DOORS AND
AutoCAD SHX Text
INT'L SYMBOL OF ACCESSIBILITY
AutoCAD SHX Text
1
AutoCAD SHX Text
SCALE: NONE
AutoCAD SHX Text
A4
AutoCAD SHX Text
60" W FROM SIDE WALL x 59" D FROM REAR WALL PER A.D.A. 604.8.1.2; COMPARTMENT DOOR SHALL NOT SWING INTO THIS AREA
AutoCAD SHX Text
3
AutoCAD SHX Text
A4
AutoCAD SHX Text
A4
AutoCAD SHX Text
FIXTURE MOUNTING HEIGHTS AND CLEARANCES
AutoCAD SHX Text
9
AutoCAD SHX Text
EQUIPMENT & ELECTRICAL DEVICES MOUNTING HEIGHTS AND CLEARANCES
AutoCAD SHX Text
GRADE 2 BRAILLE, TYPICAL
AutoCAD SHX Text
ACCEPTABLE SIGN STYLES
AutoCAD SHX Text
PROVIDE BLOCKING AS NECESSARY IN WALL TO SUPPORT PARTITIONS
AutoCAD SHX Text
18" MIN., 1-1/2" DIA. VERT. GRAB BAR
AutoCAD SHX Text
NOTE: TOILET PAPER DISPENSERS SHALL COMPLY WITH ICC/ANSI SECTION #309.4. IF MOUNTED BELOW THE GRAB BAR THE DISPENSER SHALL BE MOUNTED IN SUCH A WAY THAT THE OUTLET IS LOCATED IN AN AREA BETWEEN 24" AND 42" FROM THE REAR WALL. THE OUTLET OF THE DISPENSER SHALL BE 18 INCHES MINIMUM AND 48 INCHES MAXIMUM ABOVE THE FLOOR AND SHALL NOT BE LOCATED BEHIND THE GRAB BARS. IF THE DISPENSER IS SURFACE MOUNTED AND BELOW THE GRAB BAR IT SHALL BE AT LEAST MOUNTED WITH THE TOP OF THE DISPENSER AT LEAST 1-1/2" BELOW THE GRAB BAR - ICC/ANSI 2009 SECTION #604.7.
AutoCAD SHX Text
WALL MOUNT PHONE OUTLET
AutoCAD SHX Text
6'-8"
AutoCAD SHX Text
6'-8"
AutoCAD SHX Text
6'-8"
AutoCAD SHX Text
MANUAL FIRE ALARM PULL
AutoCAD SHX Text
WALL SCONCE
AutoCAD SHX Text
D
AutoCAD SHX Text
Q
AutoCAD SHX Text
DT
AutoCAD SHX Text
P
AutoCAD SHX Text
P/D
AutoCAD SHX Text
D
AutoCAD SHX Text
Q
AutoCAD SHX Text
DT
AutoCAD SHX Text
P
AutoCAD SHX Text
P/D
AutoCAD SHX Text
PHONE / DATA
AutoCAD SHX Text
T
AutoCAD SHX Text
SW
AutoCAD SHX Text
SW
AutoCAD SHX Text
THERMOSTAT
AutoCAD SHX Text
DUPLEX
AutoCAD SHX Text
QUADPLEX
AutoCAD SHX Text
DATA
AutoCAD SHX Text
PHONE
AutoCAD SHX Text
SWITCH
AutoCAD SHX Text
DOUBLE SWITCH
AutoCAD SHX Text
SWITCH AT DOOR OR CASED OPENING
AutoCAD SHX Text
3'-4" MIN.
AutoCAD SHX Text
3'-4" MIN.
AutoCAD SHX Text
WALL HOOKS (WALL OR DOOR MOUNTED)
AutoCAD SHX Text
IF FIRE EXTINGUISHER WEIGHT IS OVER 40 LBS., MAX. HEIGHT = 3'-6"
AutoCAD SHX Text
FIRE EXTINGUISHER CABINET
AutoCAD SHX Text
ACCESSIBLE
AutoCAD SHX Text
MIN. UNDER F.E. CAB
AutoCAD SHX Text
RAISED LETTERS
AutoCAD SHX Text
%%uNOTES:
AutoCAD SHX Text
3.
AutoCAD SHX Text
4.
AutoCAD SHX Text
1.
AutoCAD SHX Text
2.
AutoCAD SHX Text
GRADE 2 BRAILLE
AutoCAD SHX Text
NAME
AutoCAD SHX Text
(FACILITY
AutoCAD SHX Text
NAME / LOGO)
AutoCAD SHX Text
ROOM
AutoCAD SHX Text
202
AutoCAD SHX Text
5.
AutoCAD SHX Text
ACTUAL ROOM NAME / NUMBER TO BE PROVIDED BY BUILDING OWNER.
AutoCAD SHX Text
SIGN TEXT TO BE A CONTRASTING COLOR TO SIGN FIELD
AutoCAD SHX Text
SIGN TO BE A.D.A. / IBC COMPLIANT PER SEC. 703
AutoCAD SHX Text
ACTUAL SIGN DESIGN AND DIMENSIONS SHALL BE BY PROVIDED BY DESIGN / BUILD SIGNAGE CONTRACTOR IN COORDINATION WITH OWNER AND CONTRACTOR.
AutoCAD SHX Text
MEASURING BETWEEN 5/8" AND 2" HIGH.
AutoCAD SHX Text
LETTERS AND NUMERALS SHALL BE RAISED
AutoCAD SHX Text
1/32", UPPER CASE, SANS SERIF TYPE
AutoCAD SHX Text
ACCESSIBLE ENTRANCES
AutoCAD SHX Text
ACCESSIBLE TOILET AND BATHING FACILITIES
AutoCAD SHX Text
%%uINTERNATIONAL SYMBOL OF ACCESIBILITY%%u
AutoCAD SHX Text
ACCESSIBLE PASSENGER LOADING ZONES
AutoCAD SHX Text
THIS SYMBOL SHALL BE LOCATED AT:
AutoCAD SHX Text
ACCESIBLE PARKING SPACES
AutoCAD SHX Text
1A
AutoCAD SHX Text
1B
AutoCAD SHX Text
CELL WITH 2/10" SPACE BETWEEN CELLS,
AutoCAD SHX Text
GRADE II, DOTS =1/10" ON CENTER IN EACH
AutoCAD SHX Text
%%uBRAILLE CHARACTERISTICS:%%u
AutoCAD SHX Text
RAISED 1/40".
AutoCAD SHX Text
7.
AutoCAD SHX Text
6.
AutoCAD SHX Text
1B
AutoCAD SHX Text
SIDELIGHT OR WINDOW WHERE OCCURS - PROVIDE BLANK SIGN ON OPPOSITE SIDE OF GLASS TO COVER SIGN MOUNTING
AutoCAD SHX Text
%%130
AutoCAD SHX Text
OBSTRUCTIONS: THERE MUST BE A CLEAR SPACE OF 18" MINIMUM BY 18" MINIMUM, CENTERED ON TACTILE CHARACTERS, BEYOND THE ARC OF ANY DOOR SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN POSITION
AutoCAD SHX Text
MOUNTING HEIGHT = 48" MIN. ABV THE FINISH FLOOR FROM THE BASELINE OF THE LOWEST BRAILLE CELLS AND 60" MAX. ABV THE FINISH FLOOR MEASURED FROM THE BASELINE OF BASELINE OF OF THE HIGHEST LINE OF RAISED CHARACTERS.
AutoCAD SHX Text
F.O. CEILING
AutoCAD SHX Text
FIRE ALARM & VISUAL SIGNAL
AutoCAD SHX Text
SMOKE DETECTOR
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
BLOCKING FOR GRAB BAR, ETC. (ITEMS 50 LBS. OR MORE)
AutoCAD SHX Text
2
AutoCAD SHX Text
3"=1'-0"
AutoCAD SHX Text
A4
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
MISC. BLOCKING (ITEMS 50 LBS. OR LESS)
AutoCAD SHX Text
5
AutoCAD SHX Text
NONE
AutoCAD SHX Text
A4
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
NOT USED
AutoCAD SHX Text
10
AutoCAD SHX Text
A4
AutoCAD SHX Text
4 X 6 BLOCK W/
AutoCAD SHX Text
EA. END. ANCHOR
AutoCAD SHX Text
TO STUD FRM'G
AutoCAD SHX Text
(4)-16d NAILS @
AutoCAD SHX Text
FINISH AS SCHEDULED
AutoCAD SHX Text
GYP. BD.
AutoCAD SHX Text
BRACKET
AutoCAD SHX Text
WALL MOUNTING
AutoCAD SHX Text
SEALANT, TYP.
AutoCAD SHX Text
(2) #14 X 3" WOOD SCREWS PER BRACKET
AutoCAD SHX Text
A34 TOP & BOT EACH END OF BLOCK
AutoCAD SHX Text
GRAB BAR OR OTHER ITEM REQUIRING ANCHORAGE
AutoCAD SHX Text
NOTE: : 1.BACKING PLATE FOR MISC. ITEMS, I.E. BACKING PLATE FOR MISC. ITEMS, I.E. SURFACE MOUNTED MIRRORS, WASTE RECEPTACLES, TOWEL DISPENSERS, EQUIPMENT, ETC. MAX WEIGHT - 50 LBS 2.USE SELF-TAPPING SHEET WOOD USE SELF-TAPPING SHEET WOOD SCREWS WHEN ATTACHING ITEMS TO BACKING PLATE 3.ATTACH TO MINIMUM OF 3 STUDS; DO ATTACH TO MINIMUM OF 3 STUDS; DO NOT CANTILEVER IF SUPPORT IS NEDDED BEYOND STUD, CONTINUE BACKING PLATE TO NEXT STUD.
