our linkages, your solution - Automotion · PDF fileSpringfix Linkages is a division of Automotion Components ... Torque Ratings for Plain Bearing Universal Joints ... R3680.020 20

Universal Joints

...our linkages, your solution

214

Springfix Linkages is a division of Automotion Components Ltd

springfixlinkages.com

Universal Joints OverviewUniversal Joints

Single Universal Joints

Available with plain bearings or needle roller bearings. Plain bore and keyed bores stockedas standard, hex or square shaped bores on request.

Double Universal Joints

Available with plain bearings or needle roller bearings. Plain bore and keyed bores stockedas standard, hex or square shaped bores on request.

Stainless Steel Universal Joints

Single and double universal joints with plain bearings and plain bores. Keyed, hex, orsquare shaped bores available on request.

Telescopic Universal Joints

Two universal joints connected by a sliding splined shaft with the ability to extend, allowingadjustments in length during installation.

Universal Joint Bellows

Available for both single and double universal joints, bellows are used to cover and protectthe joints.

Quick Release Universal Joints

Quick change mechanism one end of the joint to allow rapid connection and release of theshaft, ideal when time is critical.

Sizes Bore sizes from 6mm diameter up to 50mm diameter.




Sizes Available to protect joints up to 58mm outside diameter.


Pages 226 - 229

Pages 222 - 225

Pages 233- 234

Pages 220 - 221

Pages 230 - 231

Pages 232

01483 266 784 215


[email protected]

Universal JointsTechnical InformationSelection and Assembly

When one single joint is coupled with two shafts (of which the driving one is rotating at aconstant speed) forming an angle, a periodic variation of the driven shaft is caused withexactly four uctuations per revolution.

The difference between the maximum and the minimum speed of the driven shaft dependson the angle formed by the two shafts. The difference grows with the an increase of the anglea°. To have a homokinetic transmission, either two opposite single joints (ensuing that that thetwo central yokes lie on the same plane and the angles are equal) or a double joint need to be tted. The irregularity caused by the former articulation is cancelled by the latter. The overalllength resulting from the coupling of the two single joints can be reduced by using a double joint.In other words, the double joint is to be considered as the shortest homokinetic transmission.

For low speed applications (Max. 1000 rpm), joints with plain bearings (rubbing bearings) aresuggested. They are able to support shock loads, motion reversals, irregular runnings andrelatively high torques. The working angles must be be restricted when using at speedsbetween 500 - 1000 rpm. Please consult our technical department if you have such an application.

For high rotation speeds, relatively low torques or wide angles, joints with needle rollerbearings are preferred. They can reach 4000 RPM dependent on the angle.

216



Technical InformationTorque Ratings for Plain Bearing Universal Joints

Universal Joints

How to read diagramsThe joint capacity to transmit a regular torque at a constant load with no shocks, for along period, mainly depends on the number of revolutions per minute and the inclinationangle a° of the two axes. The diagrams on the following pages are based on this. Eachcurve corresponds to the joint size (outside diameter “D”) and represents the torque thatthe joint can transmit depending on speed and working angle a°.

The diagrams can be directly read if angle (a°) is 10°. For wider angles, torques arereduced, therefore these are to be corrected using the correction vales (F) relating to theangle shown in the table.

IMPORTANTDiagrams’ values are merely indicative and refer to the single joints only. When choosing adouble joint, you have to consider that they can transmit a torque about 10% lower thanthe same sized single joints. Each application has its own particular motion characteristics,such as: shock loads, motion reversals, connected masses, kind of starting, presence ofelastic joints, stops and starts, etc., that have to be considered when choosing the joint.

Example

Working angle a° Correction value F

5° 1,2510° 1,0015° 0,8020° 0,6525° 0,5530° 0,45

35° 0,3840° 0,3045° 0,25

01483 266 784 217


[email protected]

Universal JointsTechnical InformationTorque Ratings for Plain Bearing Universal Joints

218



Technical InformationTorque Ratings for Needle Roller Bearings Universal Joints

Universal Joints

Example

Working angle a° Correction value F

5° 1,2510° 1,0015° 0,9020° 0,8025° 0,7030° 0,50

35° 0,4040° 0,3045° 0,25

01483 266 784

219


[email protected]

Universal JointsTechnical InformationTorque Ratings for Needle Roller Bearings Universal Joints

220 springfixlinkages.comSpringfix Linkages is a division of Automotion Components Ltd

Telescopic Universal JointsUniversal Joints

MaterialFree cutting steel (9SMnPb28k, no. 10718, greased). Bearing type: plain bearing.

Technical NotesTo DIN 808.Maximum bending angle 45° per joint. The drive speed of universal joints with journal bearings must not exceed 1000 rpm.

TipsDouble universal joints are used where large bending angles are required or where two shafts offset in relation to each other. Zinc plated available on request.

R3680

l1

l3l4 l4

d1l2

d3 l2

d2

d1 w2

w1

Order No. d1 H7 d2 l1 min. l1 max. l2 l3 stroke l4 w1 JS9 w2 shaft d3Xg

R3680.010 10 22 140 170 48 30 12 3 11,4 11x14x6 22 310R3680.110 10 22 160 200 48 40 12 3 11,4 11x14x6 22 360R3680.210 10 22 160 240 48 60 12 3 11,4 11x14x6 22 380R3680.310 10 22 230 240 48 100 12 3 11,4 11x14x6 22 500

R3680.012 12 25 160 190 56 30 13 4 13,8 13x16x6 26 500R3680.112 12 25 180 225 56 45 13 4 13,8 13x16x6 26 560R3680.212 12 25 200 270 56 70 13 4 13,8 13x16x6 26 620R3680.312 12 25 220 300 56 80 13 4 13,8 13x16x6 26 670R3680.412 12 25 250 355 56 105 13 4 13,8 13x16x6 26 760R3680.512 12 25 280 420 56 140 13 4 13,8 13x16x6 26 840R3680.612 12 25 300 450 56 150 13 4 13,8 13x16x6 26 900

R3680.014 14 28 300 200 60 30 14 5 16,3 13x16x6 29 620R3680.114 14 28 180 220 60 40 14 5 16,3 13x16x6 29 640R3680.214 14 28 200 260 60 60 14 5 16,3 13x16x6 29 720R3680.314 14 28 220 300 60 80 14 5 16,3 13x16x6 29 780R3680.414 14 28 250 350 60 100 14 5 16,3 13x16x6 29 870R3680.514 14 28 280 420 60 140 14 5 16,3 13x16x6 29 960R3680.614 14 28 300 450 60 150 14 5 16,3 13x16x6 29 1030R3680.714 14 28 350 550 60 200 14 5 16,3 13x16x6 29 1170R3680.814 14 28 400 650 60 250 14 5 16,3 13x16x6 29 1330

R3680.016 16 32 190 220 68 30 16 5 18,3 16x20x6 32 900R3680.116 16 32 210 250 68 40 16 5 18,3 16x20x6 32 980R3680.216 16 32 240 320 68 80 16 5 18,3 16x20x6 32 1100

221 01483 266 [email protected]


Telescopic Universal JointsTelescopic Universal Joints Universal Joints

R3680.316 16 32 250 350 68 100 16 5 18,3 16x20x6 32 1140R3680.416 16 32 275 390 68 115 16 5 18,3 16x20x6 32 1240R3680.516 16 32 300 430 68 130 16 5 18,3 16x20x6 32 1330R3680.616 16 32 380 590 68 210 16 5 18,3 16x20x6 32 1600R3680.716 16 32 400 630 68 230 16 5 18,3 16x20x6 32 1730



R3680.022 22 45 250 280 95 30 22 6 24,8 23x28x6 47 2350R3680.122 22 45 270 320 95 50 22 6 24,8 23x28x6 47 2510R3680.222 22 45 290 350 95 60 22 6 24,8 23x28x6 47 2670R3680.322 22 45 330 430 95 100 22 6 24,8 23x28x6 47 3000R3680.422 22 45 330 470 95 120 22 6 24,8 23x28x6 47 3160R3680.522 22 45 330 710 95 240 22 6 24,8 23x28x6 47 4130



Order No. d1 H7 d2 l1 min. l1 max. l2 l3 stroke l4 w1 JS9 w2 shaft d3Xg


Double Universal JointUniversal Joints

MaterialFree cutting steel (9 SMnPb28k, no. 10718).Bearing type: Plain bearing.

Technical NotesTo DIN 808/7551.

Maximum bending angle 45° per joint.

Max. drive speed of joints with journal bearings 1000 rpm.

TipsDouble universal joints are used where large bending angles are required or where two shafts offset in relation to each other.

Product variations available on request: needle bearings, square bores and hex bores. For stainless steel see R3696.

R3684

l4 d1 w2

w1

d2

l2 l3 l2

l1

d1

Order No. Bore d1 H7 d2 l1 l2 l3 l4 w1 JS9 w2Xg

R3684.010 Round Bore 10 16 74 26 22 15 - - 80R3684.012 Round Bore 12 22 88 31 26 18 - - 200R3684.016 Round Bore 16 25 104 37 30 21 - - 300R3684.020 Round Bore 20 32 124 43 38 24 - - 500R3684.025 Round Bore 25 42 156 54 48 31 - - 1200R3684.030 Round Bore 30 50 188 66 56 38 - - 1700R3684.040 Round Bore 40 70 238 83 72 47 - - 4300

R3684.210 with keyway 10 16 74 26 22 15 3 11,4 80R3684.212 with keyway 12 22 88 31 26 18 4 13,8 200R3684.216 with keyway 16 25 104 37 30 21 5 18,3 300R3684.220 with keyway 20 32 124 43 38 24 6 22,8 500R3684.225 with keyway 25 42 156 54 48 31 8 28,3 1200R3684.230 with keyway 30 50 188 66 56 38 8 35,3 1700R3684.240 with keyway 40 70 238 83 72 47 12 43,3 4300



Double Universal JointDouble Universal Joint Universal Joints

MaterialFree cutting steel (9SMnPb28k, no. 10718).Bearing type: Plain bearing.

Technical NotesTo DIN 808.



TipsDouble universal joints are used where large bending angles are required or where two shafts offset in relation to each other.

Product variations available on request: square bores and hex bores.

For stainless steel see part number R3696, for needle roller bearings see part number R3686.

R3685

l4 d1 w2

w1

d2

l2 l3 l2

l1

d1


R3685.006 Round Bore 6 16 56 17,0 22 8 - - 80R3685.008 Round Bore 8 16 62 20,0 22 11 - - 80R3685.010 Round Bore 10 22 74 24,0 26 12 - - 150R3685.012 Round Bore 12 25 86 28,0 30 13 - - 250R3685.014 Round Bore 14 28 96 30,0 36 14 - - 400R3685.016 Round Bore 16 32 104 34,0 36 16 - - 450R3685.018 Round Bore 18 36 114 37,0 40 17 - - 700R3685.020 Round Bore 20 42 128 41,0 46 18 - - 1000R3685.022 Round Bore 22 45 145 47,5 50 22 - - 1550R3685.025 Round Bore 25 50 163 54,0 55 26 - - 2000R3685.030 Round Bore 30 58 190 61,0 68 29 - - 2900R3685.032 Round Bore 32 58 198 65,0 68 33 - - 3000R3685.035 Round Bore 35 70 212 70,0 72 35 - - 4750R3685.040 Round Bore 40 80 245 80,0 85 39 - - 7200R3685.050 Round Bore 50 95 290 95,0 100 46 - - 12,000

R3685.206 With Keyway 6 16 56 17,0 22 8 2 7 80R3685.208 With Keyway 8 16 62 20,0 22 11 2 9 80R3685.210 With Keyway 10 22 74 24,0 26 12 3 11,4 150R3685.212 With Keyway 12 25 86 28,0 30 13 4 13,8 250


Double Universal JointUniversal Joints

R3685.214 With Keyway 14 28 96 30,0 36 14 5 16,3 400R3685.216 With Keyway 16 32 104 34,0 36 16 5 18,3 450R3685.218 With Keyway 18 36 114 37,0 40 17 6 20,8 700R3685.220 With Keyway 20 42 128 41,0 46 18 6 22,8 1000R3685.222 With Keyway 22 45 145 47,5 50 22 6 24,8 1550R3685.225 With Keyway 25 50 163 54,0 55 26 8 28,3 2000R3685.230 With Keyway 30 58 190 61,0 68 29 8 33,3 2900R3685.232 With Keyway 32 58 198 65,0 68 33 10 35,3 3000R3685.235 With Keyway 35 70 212 70,0 72 35 10 38,3 4750R3685.240 With Keyway 40 80 245 80,0 85 39 12 43,3 7200R3685.250 With Keyway 50 95 290 95,0 100 46 14 53,8 12,000




Double Universal JointNeedle roller bearingsDouble Universal JointNeedle roller bearings

Universal Joints

MaterialFree cutting steel (9SMnPb28k, no. 10718).Bearing type: needle roller bearing.



Max. drive speed of joints 4000 rpm.

TipsDouble universal joints are used where large bending angles are required or where two shafts offset in relation to each other. Product variations available on request: square bores and hex bores.

R3686

l4 d1 w2

w1

d2

l2 l3 l2

l1

d1


R3686.010 Round Bore 10 22 74 24,0 26 12 - - 150R3686.012 Round Bore 12 25 86 28,0 30 13 - - 250R3686.014 Round Bore 14 28 96 30,0 36 14 - - 400R3686.016 Round Bore 16 32 104 34,0 36 16 - - 450R3686.018 Round Bore 18 36 114 37,0 40 17 - - 700R3686.020 Round Bore 20 42 128 41,0 46 18 - - 1000R3686.022 Round Bore 22 45 145 47,5 50 22 - - 1550R3686.025 Round Bore 25 50 163 54,0 55 26 - - 2000R3686.030 Round Bore 30 58 190 61,0 68 29 - - 2900R3686.032 Round Bore 32 58 198 65,0 68 33 - - 3000R3686.035 Round Bore 35 70 212 70,0 72 35 - - 4750R3686.040 Round Bore 40 80 245 80,0 85 39 - - 7200R3686.050 Round Bore 50 95 290 95,0 100 46 - - 12,000

R3686.210 With Keyway 10 22 74 24,0 26 12 3 11,4 150R3686.212 With Keyway 12 25 86 28,0 30 13 4 13,8 250R3686.214 With Keyway 14 28 96 30,0 36 14 5 16,3 400R3686.216 With Keyway 16 32 104 34,0 36 16 5 18,3 450R3686.218 With Keyway 18 36 114 37,0 40 17 6 20,8 700R3686.220 With Keyway 20 42 128 41,0 46 18 6 22,8 1000R3686.222 With Keyway 22 45 145 47,5 50 22 6 24,8 1550R3686.225 With Keyway 25 50 163 54,0 55 26 8 28,3 2000R3686.230 With Keyway 30 58 190 61,0 68 29 8 33,3 2900R3686.232 With Keyway 32 58 198 65,0 68 33 10 35,3 3000R3686.235 With Keyway 35 70 212 70,0 72 35 10 38,3 4750R3686.240 With Keyway 40 80 245 80,0 85 39 12 43,3 7200R3686.250 With Keyway 50 95 290 95,0 100 46 14 53,8 12,000


Single Universal JointUniversal Joints

MaterialFree cutting steel (9SMnPb28k, no. 10718).Bearing type: plain bearing.

Technical NotesTo DIN 808/7551.

Maximum bending angle 45° per joint. Max. drive speed of joints with journal bearings 1000 rpm.

TipsSingle universal joints are used where shafts off-set towards each other. Product variations available on request: square bores and hex bores. For stainless steel see R3694.

For needle roller bearings see part number R3690.

R3688

d1 w2

w1

d2

l2 l2

l1

l3

Order No. Bore d1 H7 d2 l1 l2 l3 w1 JS9 w2Xg

R3688.010 Round Bore 10 16 52 26 15 - - 50R3688.012 Round Bore 12 22 62 31 18 - - 120R3688.016 Round Bore 16 25 74 37 21 - - 200R3688.020 Round Bore 20 32 86 43 24 - - 350R3688.025 Round Bore 25 42 108 54 31 - - 800R3688.030 Round Bore 30 50 132 66 38 - - 1200R3688.040 Round Bore 40 70 166 83 47 - - 2900

R3688.210 With keyway 10 16 52 26 15 3 11,4 50R3688.212 With keyway 12 22 62 31 18 4 13,8 120R3688.216 With keyway 16 25 74 37 21 5 18,3 200R3688.220 With keyway 20 32 86 43 24 6 22,8 350R3688.225 With keyway 25 42 108 54 31 8 28,3 800R3688.230 With keyway 30 50 132 66 38 8 33,3 1200R3688.240 With keyway 40 70 166 83 47 12 43,3 2900



Single Universal JointSingle Universal Joint Universal Joints

MaterialFree cutting steel (9SMnPb28k, no. 10718).Bearing type: journal bearing.




TipsSingle universal joints are used where shafts off-set toward each other.

Product variations available on request: square bores and hex bores.

For stainless steel see R3694.

R3689

d1 w2

w1

d2

l2 l2

l1

l3


R3689.006 Round Bore 6 16 34 17 8 - - 50R3689.008 Round Bore 8 16 40 20 11 - - 50R3689.010 Round Bore 10 22 48 24 12 - - 100R3689.012 Round Bore 12 25 56 28 13 - - 160R3689.014 Round Bore 14 28 60 30 14 - - 200R3689.016 Round Bore 16 32 68 34 16 - - 300R3689.018 Round Bore 18 36 74 37 17 - - 450R3689.020 Round Bore 20 42 82 41 18 - - 600R3689.022 Round Bore 22 45 95 47,5 22 - - 950R3689.025 Round Bore 25 50 108 54 26 - - 1200R3689.030 Round Bore 30 58 122 61 29 - - 1850R3689.032 Round Bore 32 58 130 65 33 - - 2000R3689.035 Round Bore 35 70 140 70 35 - - 3150R3689.040 Round Bore 40 80 160 80 39 - - 4600R3689.050 Round Bore 50 95 190 95 46 - - 7600

R3689.206 With Keyway 6 16 34 17 8 2 7 50R3689.208 With Keyway 8 16 40 20 11 2 9 50R3689.210 With Keyway 10 22 48 24 12 3 11,4 100R3689.212 With Keyway 12 25 56 28 13 4 13,8 160R3689.214 With Keyway 14 28 60 30 14 5 16,3 200R3689.216 With Keyway 16 32 68 34 16 5 18,3 300R3689.218 With Keyway 18 36 74 37 17 6 20,8 450R3689.220 With Keyway 20 42 82 41 18 6 22,8 600R3689.222 With Keyway 22 45 95 47,5 22 6 24,8 950


Single Universal JointUniversal Joints

R3689.225 With Keyway 25 50 108 54 26 8 28,3 1200R3689.230 With Keyway 30 58 122 61 29 8 33,3 1850R3689.232 With Keyway 32 58 130 65 33 10 35,3 2000R3689.235 With Keyway 35 70 140 70 35 10 38,3 3150R3689.240 With Keyway 40 80 160 80 39 12 43,3 4600R3689.250 With Keyway 50 95 190 95 46 14 53,8 7600




Single Universal jointNeedle roller bearingSingle Universal jointNeedle roller bearing

Universal Joints

MaterialFree cutting steel (9SMnPb28k, no. 10718).Bearing type: needle roller bearing.

Technical NotesTo DIN 808.Maximum bending angle 45° per joint. Roller bearing lubricated for life. No maintenance required. Precise, silent and smooth running. Max. drive speed of 4000 rpm.

TipsSingle universal joints are used where shafts off-set towards each other. Product variations available on request: square bores and hex bores.

R3690

d1 w2

w1

d2

l2 l2

l1

l3


R3690.010 Round Bore 10 22 48 24 12 - - 100R3690.012 Round Bore 12 25 56 28 13 - - 160R3690.014 Round Bore 14 28 60 30 14 - - 200R3690.016 Round Bore 16 32 68 34 16 - - 300R3690.018 Round Bore 18 36 74 37 17 - - 450R3690.020 Round Bore 20 42 82 41 18 - - 600R3690.022 Round Bore 22 45 95 47,5 22 - - 950R3690.025 Round Bore 25 50 108 54 26 - - 1200R3690.030 Round Bore 30 58 122 61 29 - - 1850R3690.032 Round Bore 32 58 130 65 33 - - 2000R3690.035 Round Bore 35 70 140 70 35 - - 3150R3690.040 Round Bore 40 80 160 80 39 - - 4600R3690.050 Round Bore 50 95 190 95 46 - - 7600

R3690.210 With Keyway 10 22 48 24 12 3 11,4 100R3690.212 With Keyway 12 25 56 28 13 4 13,8 160R3690.214 With Keyway 14 28 60 30 14 5 16,3 200R3690.216 With Keyway 16 32 68 34 16 5 18,3 300R3690.218 With Keyway 18 36 74 37 17 6 20,8 450R3690.220 With Keyway 20 42 82 41 18 6 22,8 600R3690.222 With Keyway 22 45 95 47,5 22 6 24,8 950R3690.225 With Keyway 25 50 108 54 26 8 28,3 1200R3690.230 With Keyway 30 58 122 61 29 8 33,3 1850R3690.232 With Keyway 32 58 130 65 33 10 35,3 2000R3690.235 With Keyway 35 70 140 70 35 10 38,3 3150R3690.240 With Keyway 40 80 160 80 39 12 43,3 4600R3690.250 With Keyway 50 95 190 95 46 14 53,8 7600


Bellowsfor single universal joints

Universal Joints

MaterialRubber.

TipsBellows give universal joints full protection against ingress of dirt. They can be filled with grease which gives long term lubrication for friction bearings. Bellows should be secured at each end with two cable ties (not supplied).

R3691

d2

l

d1

Order No. To suit joint of o.d d1 d2 l

R3691.016 16 15,0 28 34R3691.018 18 16,5 32 40R3691.022 22 20,5 40 45R3691.025 25/26 24,5 48 50R3691.028 28/29 27,5 52 56R3691.032 32 30,5 56 65R3691.036 36/37 35,5 66 72R3691.042 42 40,0 75 82R3691.045 45/47 45,0 84 95R3691.050 50/52 50,0 92 108R3691.058 58 56,0 100 122



Bellowsfor double universal jointsBellowsfor double universal joints

Universal Joints

MaterialBlack elastomer plastic (smooth PVC).

TipsBellows give universal joints full protection against ingress of dirt. They can be filled with grease which gives long term lubrication for friction bearings. Bellows should be secured at each end with two cable ties (not supplied).

R3692l

d1 d2

Order No. To suit joint of o.d d1 d2 l

R3692.016 16 16 35 55R3692.022 22 20 36 65R3692.025 25 24 44 70R3692.028 28 28 51 80R3692.032 32 32 62 90R3692.042 42 40 73 120R3692.050 50 50 90 155


Universal Jointwith quick change coupling

Universal Joints

MaterialFree cutting steel (9 SMnPb28 k, no. 10718, greased).

Bearing type: plain bearing.




TipsRapid change coupling ideal where time is critical. Retention of shaft accomplished with two ball bearings engaging the shaft via a round bore with keyway.

Product variations available on request: needle bearings and hex shaped bores.(Keyway and hex shaped bores on quick change end only unless requested otherwise.)

R3693d2

d1

l3

d4d4/2

l4

l2 l2

l1

d1 d2

d1

d3

d3

w2

w1

Order No. d1 H7 d2 l1 l2 l3 l4 d3 d4 w1 JS9 w2Xg

R3693.010 10 22 62 31 17 11,5 8,7 4 3 11 100R3693.012 12 25 74 37 21 13,5 11 4 4 13,3 160R3693.014 14 25 74 37 21 13,5 13 4 5 15,3 160R3693.016 16 32 86 43 24 14 14,8 6,35 5 17,3 310R3693.018 18 36 96 48 28 19 16 8 6 19,8 460R3693.020 20 42 108 54 31 19 18 8 6 22,8 610R3693.022 22 45 120 60 34 20,5 20 10 6 24,8 960R3693.025 25 50 132 66 38 20,5 23 10 8 28,3 1150R3693.030 30 58 166 83 49 25 28 10 8 33,3 2080



Stainless Single Universal JointStainless Single Universal Joint Universal Joints

MaterialStainless steel (AISI 304).

Technical NotesTo DIN 808.Maximum bending angle 45° per joint.

TipsProduct variations available on request: Keyways, square bores and hexshaped bores.

R3694

d1

d2

l2 l2

l1

l3

Order No. d1 H7 d2 l1 l2 l3Xg

R3694.006 6 16 34 17 8 50R3694.008 8 16 40 20 11 50R3694.010 10 22 48 24 12 100R3694.012 12 25 56 28 13 160R3694.016 16 32 68 34 16 300R3694.020 20 42 82 41 18 600R3694.025 25 50 108 54 26 1200R3694.030 30 58 122 61 29 1850


Stainless Double Universal JointUniversal Joints

MaterialStainless steel (AISI 304).

Technical NotesTo DIN 808.Maximum bending angle 45° per joint.

TipsProduct variations available on request: Keyways, square bores and hexshaped bores.

R3696

l4 d1

d2

l2 l3 l2

l1

d1

Order No. d1 H7 d2 l1 l2 l3 l4Xg

R3696.006 6 16 56 17 22 8 80R3696.008 8 16 62 20 22 11 80R3696.010 10 22 74 24 26 12 150R3696.012 12 25 86 28 30 13 250R3696.016 16 32 104 34 36 16 450R3696.020 20 42 128 41 46 18 1000R3696.025 25 50 163 54 55 26 2000R3696.030 30 58 190 61 68 29 2900

Documents

our linkages, your solution - Automotion · PDF fileSpringfix Linkages is a division of Automotion Components ... Torque Ratings for Plain Bearing Universal Joints ... R3680.020 20