Upload
flexiforce
View
230
Download
2
Tags:
Embed Size (px)
DESCRIPTION
Â
Citation preview
www.flexiforce.com
manual
pass doors switch kitINSTALLATION / MAINTENANCE © All rights reserved. FlexiForce®, 2010
OSE-PDSK-IND/RES
GB
www.flexiforce.com
manualATTENTION! GENERAL WARNINGS!
To install, use and maintain this pass doors switch kit safely, a number of precautions must be taken. For the safety of all concerned pay heed to the warnings and instructions given below! If in doubt, contact your supplier.
99 This manual has been written for use by experienced fitters and as such is not suitable for d.i.y. purposes or for use by trainee fitters.
99 This manual describes the installation of certain hardware set components. Be sure to supplement this manual if needed with instructions for any additional components not described in this manual.
99 Before starting, read this manual carefully!99 Certain components may be sharp or have jagged edges. As such you are advised to wear safety gloves.99 During tensioning, springs can exert large forces. Work carefully. Use the proper equipment. Ensure that you are standing in a steady position.
99 Ensure that there is sufficient light during installation. Remove obstacles and dirt. Make sure that there is no one else present other than the fitters. Other people (children!) may get in the way or endanger themselves during the installation.
TERMS AND CONDITIONSThe general terms and conditions of delivery and payment issued by the Metaalunie and designated as METAALUNIE CONDITIONS are fully applicable to all our quotations, contracts and their implementation. We expressly reject all other terms and conditions. On request we will send you a copy of these terms and conditions free of charge. A copy may also be downloaded from our website www.flexiforce.nl.
CONTACTFlexiForce Group B.V.P.O. Box 373770 AA BarneveldThe NetherlandsTel. +31-(0)[email protected]
GB
FF-MANUAL OSE-PDSK-IND/RES
www.flexiforce.com
manual
OSE-SCB1OSE-SCB1
Drill 6.5 mmDrill 19.0 mm
(-)(+)
13 mm
13 mm
CONTENT OF PACKAGING
GB
FF-MANUAL OSE-PDSK-IND/RES
FF-MANUAL OSE-PDSK-IND
FF-MANUAL OSE-PDSK-RES
TOOLS REQUIRED FOR CORRECT AND RAPID ASSEMBLY
1,5 m
200 mm200 mm
1 m
1 m (x4)
750 mm (x4)
OSE-SCB1OSE-MPDS (5 m) OSE-LAD2
OSE-1113926
OSE-1113704W
OSE-MPDS (5 m) 5 mOSE-LAD1
www.flexiforce.com
manualFig. a
Fig. 4Fig. 3
Fig. 5 Fig. 6
Fig. 2Fig. 1
Ø 19mm
Ø 19mm
GB
ASSEMBLY of OSE-PDSK-IND/RES
FF-MANUAL OSE-PDSK-IND/RES
manual
www.flexiforce.comFF-MANUAL OSE-PDSK-IND/RES
Fig. 7 Fig. 8
Fig. 10
Fig. 11
Fig. 9
Fig. 12FF-MANUAL OSE-PDSK-RES FF-MANUAL OSE-PDSK-RES
www.flexiforce.com
GB
ASSEMBLY of OSE-PDSK-IND/RES
FF-MANUAL OSE-PDSK-IND
1006B
1062M
manual
www.flexiforce.comwww.flexiforce.com
Fig. 13
Remarks:
GB
FF-MANUAL OSE-PDSK-IND/RES
FF-MANUAL OSE-PDSK-RES
manualw
www.flexiforce.comFF-MANUAL OSE-PDSK-IND/RES
Wiring instructions to most common CDO controls by brand
GB
Mtec
MFZ
control unit UST2 L
Terminal block X5 connector J6 (remove bridge)
control unit CS300
Terminal block X3 connectors 1 & 2 (remove bridge)
control unit UST1 KL
Terminal block K2 connector J10 (remove bridge)
control unit CS100
Terminal block X13 connectors 1 & 2 (remove bridge)
control unit AS100
Terminal block X3 connectors 4 & 5 (remove bridge)
control unit AS210B
Terminal block X3 connectors 14 & 15 (remove bridge)
Dalmaticmini std. V7E
Long terminal strip connectors 28 & 29
GAROGAS210
Long terminal strip connectors 16 & 17
GfATS970
Terminal block X3 connectors 3.1 & 3.2