Embed Size (px)
Citation preview
Activate ORFICAST™ in waterof 65°C (149°F) during 1 minute. Dry heating is alsopossible (see instructions for use).
1 Dry ORFICAST™ slightly. The tape can also be appliedin wet condition.
2
Overlap the material duringfolding. Make sure the overlapping does not covermore than half the size ofthe total width of the ORFICAST™ tape.
4Apply circularly fromdistal to proximal. Stretchthe material slightly duringapplication.
3
Finishing: Dry or wet heatthe edges and fold downgently. Pressed material results inpermanent attachment.Material not pressed: nopermanent attachment (it ispossible to loosen the layers)
5 Fixation of loop tape: dryheat ORFICAST™ locally withhot air and press firmlytogether.
6
CIRCULAR FINGER SPLINT
Activate ORFICAST™ in waterof 65°C (149°F) during 1 minute. Dry heating is alsopossible (see instructions for use).
1 Application: apply circularlyfrom distal to proximal.Stretch the material slightlyduring application.
2
Mold the material over thepalmar side to conform tothe anatomy and arches ofthe hand.
4Overlap the material duringfolding. Make sure the overlapping does not covermore than half the size ofthe total width of the ORFICAST™ tape.
3
Mold material from the ulnarside to the radial side, overthe dorsal part of the handand back to the thumb andas such wrapping it aroundthe hand.
5 Finishing: wet or dry heatthe edges and fold downgently.
6
THUMB SPLINT
ORFICAST™ THERMOPLASTIC TAPE
drivenbycare
ORFICAST™ THERMOPLASTIC TAPE
All
rig
hts
rese
rved
. No
par
t of t
his
pub
licat
ion
may
be
pro
duc
ed, s
tore
d in
a re
trie
val s
yste
m o
r tra
nsm
itte
d, in
any
way
, for
m o
r by
any
mea
ns,
ele
ctro
nic
, mec
han
ical
, ph
otoc
opyi
ng
or o
ther
wis
e, w
ith
out p
rior
wri
tten
per
mis
sion
of O
rfit
Ind
ustr
ies.
©
ORF
IT In
dus
trie
s
The seams from overlapping that are visible on the outside are not perceptible on the inside which gives ORFICAST™ a very soft surface to thetouch.
ORFICAST™ is extremely comfortable for your patient
MALLET FINGER SPLINT
Activate ORFICAST™ in water of65°C (149°F) during 1 minute.Fold the material in two layersafter heating.
1
Press the lateral edges firmly to-gether.
5
Press the folded material firmlytogether.
2 If necessary, stretch ORFICAST™broadwise.
3 Apply the pressed material onthe volar and dorsal fingertip.
4
Take off the splint and mark trimming lines
6 Cut away excess material.7 Apply hook and loop tape byusing hot air and pressing firmlytogether.
8
drivenbycare Art. Nr. 22076E
ORFIT Industries • Vosveld 9A • B-2110 Wijnegem • BelgiumPhone: (+32) (0) 3.326.20.26 • Fax: (+32) (0) 3.326.14.15
e-mail: [email protected] • www.orfit.com
21-0
3-20
11
EU:Patent application No. 08164533.5 filed on September 17, 2008
Published on April 22, 2009 with No. 2050848)
USA:Patent application N° 12/212,124 filed on September 17, 2008
Published on March 19, 2009 under N° 2009/0075542 - publication)
ORFIT® Industries America • 350 Jericho Turnpike, Suite 101 • Jericho, New York 11753Toll Free: 1-888-ORFIT-US (1-888-673-4887) • Tel: 516-935-8500
Toll Free Fax: 1-877-935-8505 • Fax: 516-935-8505E-mail: [email protected] • www.orfit.com
