Optical Disc Drive (ODD) - Rockwell Automation · c. Secure the ODD backplane board with the two screws you removed in step 3-b. d. Secure the new ODD module using the four screws

O

Ca

AbTh

rep

no

To

Ab

Im

El

Vo

Ab

Be

Re

Pr

In

Re

Re

Re

Po

Ad

Installation Instructions

ptical Disc Drive (ODD)

talog Number 6189V-SLDUAL

pic Page

out This Publication 1

portant User Information 2

ectrostatic Discharge (ESD) Precautions 3

ltage Precautions 3

out the Optical Disc Drive (ODD) 4

fore You Begin 4

quired Tools 4

e-installation Procedure 5

Publication 6177R-IN004B-EN-P - November 2009

out This Publicationis publication provides pre- and post-installation information and procedures on how to

lace the optical disc drive (ODD) in the VersaView Light Industrial 750R and 1450R

n-display computers.

stall the Optical Disc Drive (ODD) 5

move the Side Cover 5

place the Optical Disc Drive (ODD) 7

install the Cover 10

st-installation Procedure 11

ditional Resources 11

2 Opti

Publicati

Impor

Solid staSafety GSGI-1.1 http://litequipmewide varsatisfy t

In no everesulting

The examvariableassume

No pateequipme

ReproduAutomat

Through

WAR

IMPO

ATTEN

SHOCK

BURN

cal Disc Drive (ODD)

tant User Information

te equipment has operational characteristics differing from those of electromechanical equipment. uidelines for the Application, Installation and Maintenance of Solid State Controls (publication

available from your local Rockwell Automation sales office or online at erature.rockwellautomation.com) describes some important differences between solid state nt and hard-wired electromechanical devices. Because of this difference, and also because of the iety of uses for solid state equipment, all persons responsible for applying this equipment must

hemselves that each intended application of this equipment is acceptable.

nt will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages from the use or application of this equipment.

ples and diagrams in this manual are included solely for illustrative purposes. Because of the many s and requirements associated with any particular installation, Rockwell Automation, Inc. cannot responsibility or liability for actual use based on the examples and diagrams.

nt liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, nt, or software described in this manual.

ction of the contents of this manual, in whole or in part, without written permission of Rockwell ion, Inc., is prohibited.

out this manual, when necessary, we use notes to make you aware of safety considerations.

NINGIdentifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.

on 6177R-IN004B-EN-P - November 2009

RTANT Identifies information that is critical for successful application and understanding of the product.

TIONIdentifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you to identify a hazard, avoid a hazard, and recognize the consequences.

HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present.

HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures.

http://www.literature.rockwellautomation.com


Electr

Follow t

•

•

•

•

••

•

VoltagThe com

or remo

ATTEN

SHOCK H

Optical Disc Drive (ODD) 3

ostatic Discharge (ESD) Precautions

hese precautions to prevent ESD discharge:

Transport the computer and replacement parts in static-safe containers such as

conductive tubes, bags, or boxes.

Keep electrostatic-sensitive parts in their containers until they arrive at static-free

stations.

Cover workstations with approved static-dissipating material. Use a wrist strap

connected to the work surface and properly grounded (earthed) tools and equipment.

Keep work area free of nonconductive material, such as ordinary plastic assembly aids

and foam packing.

Avoid touching pins, leads, or circuitry.

Always handle the optical disc drive (ODD) by its metal frame and do not touch its

internal components.

Always hold components with a printed circuit board (PCB) by its edges and lay it

with the assembly-side down.

TIONElectrostatic discharge (ESD) can damage static-sensitive devices or microcircuitry. Observe proper packaging and grounding techniques to prevent damage.


e Precautionsputers contain line voltages. Disconnect all power to the computer before you install

ve system components.

AZARDDisconnect power from the computer before removing components. Failure to disconnect power could result in severe electrical shock and/or damage the computer.

4 Opti

Publicati

About

The OD

be writte

burning

writing d

BeforReview

compati

informa

RequirThese to

•••

ATTEN


the Optical Disc Drive (ODD)

D supports reading and writing data to compatible CD and DVD media. Data may

n to CD media by using either the Windows XP CD writing wizard or the DVD

software provided with this product. The burning software must be used when

ata to DVD media.

e You Beginthe specifications of a new component before installing it to make sure it is

ble with the computer. Record the model and serial number, and any other pertinent

tion of new components for future reference.

ed Toolsols are required:

TIONTo avoid voiding your product warranty, use only Rockwell Automation Allen-Bradley approved replacement parts and accessories.


#2 Phillips screwdriver

Antistatic wrist band (ships with product)

Small wire cutter

Pre-ins

Perform

hardwar

1. T

2.

3.

InstalYou can

CD-RO

RemovFollow t

1. P

2.

IMPOR

IMPOR


tallation Procedure

this pre-installation procedure before removing the side cover or accessing a

e component.

urn off the computer and all peripherals connected to it.

If necessary, label each one to expedite reassembly.

Disconnect power from the computer to avoid exposure to high energy levels.

Disconnect telecommunication cables to avoid exposure to shock hazards from

ringing voltages.

l the Optical Disc Drive (ODD)

TANT Make sure to read and understand the entire installation or removal procedure before you begin to configure the computer hardware.

TANT When installing hardware components that require access to internal components, first back up all computer data to avoid loss of data.


install or replace the ODD in your computer. The computers support slim type

M, DVD-ROM/CD-RW, and DVD-RW drives.

e the Side Coverhese procedures to remove the cover of the computer.

erform the pre-installation procedure.

Unfasten the side cover from the system chassis by removing the two screws located

on the rear edge of the side cover.

6 Opti

Publicati

3.

RC


Slide the cover back about 1.5 cm (0.5 in.), then pull the panel away from the chassis.

XX

. XX

XX

X. X

X

Removing the Side Cover on the 750R Computer

emoving the Side Cover on the 1450R omputer

XX.XXXXX.X

X


ReplacFollow t

1. D

2.

3.

4.


e the Optical Disc Drive (ODD)his procedure to install or replace an ODD.

isconnect the the interface cable from the ODD backplane board.

This cable contains both IDE data and power to the drive.

Cut the cable tie closest to the ODD backplane connector.

Remove the ODD assembly from the computer.

a. Remove the two screws securing the ODD carrier to the system drive cage.

b. Detach the ODD from the system drive cage.

a

b


Remove the ODD module from its carrier.

a. Remove and discard the four screws securing the ODD module to its carrier.

b. Remove the two screws securing the ODD backplane board.

Retain these screws for reassembly.

c. Detach the ODD backplane board from the ODD module.

8 Opti

Publicati

5.

6.

7.


d. Detach the ODD module from its carrier.

Remove the new ODD module from its protective packaging.

Install the new ODD module to its carrier.

a. Lay the ODD module on its carrier.

b. Attach the ODD backplane board to the new ODD module.

c. Secure the ODD backplane board with the two screws you removed in step 3-b.

d. Secure the new ODD module using the four screws (M2x2.5) supplied with the

accessory kit.

a

a

a

a

b

bc

d


The original screws you removed in step 3-a may not be compatible with your new

ODD.

Install the new ODD assembly on the system drive cage.

a

b c

c

d

d

d

d

8.

9.

10.


a. Align the ODD assembly on top of the system drive cage.

b. Secure the ODD assembly to the cage with the two screws you removed in step

2-a.

Connect the IDE cable on the ODD backplane board and install the new cable tie in

the same manner as the original configuration.

Reinstall the side cover.

Perform the post-installation procedure.

b

a


10 Opt

Publicati

ReinstAfter co

side cov

1. M

2.

3.

Rei

ical Disc Drive (ODD)

all the Covermpleting any removal or replacement procedure of internal components, reinstall the

er.

ake sure the computer is in its normal upright position.

Perform steps 1…3 of the post-installation procedure.

Reinstall the side cover.

a. Position the lower edge of the side cover at an angle to the hinge tabs along the

bottom of the chassis.

b. Rest the cover on the hinge tabs, tilting it up until it engages the locking

mechanism at the top of the chassis.

c. Slide the cover towards the front panel to position it into place.

d. Secure the cover once it is attached to the chassis by replacing the two screws

located on the rear edge of the side cover.

Reinstalling the Side Cover on the 750R Computer


XX

. XX

XX

X. X

X

XX.XXXXX.X

X

nstalling the Side Cover on the 14750R Computer

Post-iPerform

1. M

2.

3.

4.

5.

6.

AdditFor add

to these

You can

order pa

distribut

Resourc

VersaVieNon-dispManual,6177R-U

VersaVieNon-dispInstallatpublicat


nstallation Procedure this post-installation procedure after installing or removing a hardware component.

ake sure all components are installed according to the step-by-step instructions.

Make sure that no loose tools or parts are left inside the computer.

Reinstall any expansion boards, peripherals, board covers, and system cables that have

been previously removed.

Reinstall the side cover, if necessary.

Connect all external cables and power to the computer.

Press the power switch to turn on the computer.

ional Resourcesitional information on the VersaView Light Industrial Non-display computers, refer

publications.

e Description

w Light Industrial lay Computers User

Gives an overview of the system and provides procedures to install the computer,


view or download publications at http://literature.rockwellautomation.com. To

per copies of technical documentation, contact your local Rockwell Automation

or or sales representative.

publication M001

set up computer connections, operate the computer, and troubleshoot the computer.

w Light Industrial lay Computers

ion Instructions, ion 6177R-IN001

Provides pre-installation instructions and procedures to machine/wall mount the 750R computer and rack mount the 1450R computer. It also describes how to make peripheral, power, and network connections.


PublicatiSupersedes Pub

RockwRockwel

using its

technica

sample c

can cust

For an a

and trou

informa

or visit h

InstallaIf you ex

installati

also con

module

New PRockwel

shipped

function

Allen-Brad

Automatio

Trademark

United S

OutsideStates

United S

OutsideStates

ell Automation Supportl Automation provides technical information on the Web to assist you in

products. At http://support.rockwellautomation.com, you can find

l manuals, a knowledge base of FAQs, technical and application notes,

ode and links to software service packs, and a MySupport feature that you

omize to make the best use of these tools.

dditional level of technical phone support for installation, configuration,

bleshooting, we offer TechConnect Support programs. For more

tion, contact your local distributor or Rockwell Automation representative,

ttp://support.rockwellautomation.com.

tion Assistanceperience a problem with a hardware module within the first 24 hours of

on, please review the information that's contained in this manual. You can

tact a special Customer Support number for initial help in getting your

up and running.

roduct Satisfaction Returnl tests all of its products to ensure that they are fully operational when

from the manufacturing facility. However, if your product is not

ing, it may need to be returned.

tates 1.440.646.3223Monday – Friday, 8am – 5pm EST

United Please contact your local Rockwell Automation representative for any technical support issues.

on 6177R-IN004B-EN-P - November 2009 41061-377-01(2)lication 6177R-IN004A-EN-P - October 2006 Copyright © 2009 Rockwell Automation, Inc. All rights reserved. Printed in China.

ley, Rockwell Automation, TechConnect, and VersaView are registered trademarks of Rockwell

n.

s not belonging to Rockwell Automation are property of their respective companies.

tates Contact your distributor. You must provide a Customer Support case number (see phone number above to obtain one) to your distributor in order to complete the return process.

United Please contact your local Rockwell Automation representative for return procedure.

http://support.rockwellautomation.com

http://support.rockwellautomation.com

Documents

Optical Disc Drive (ODD) - Rockwell Automation · c. Secure the ODD backplane board with the two screws you removed in step 3-b. d. Secure the new ODD module using the four screws