OPERATIONAL & MAINTENANCE MANUAL SEM Model · PDF fileSecurity Engineered Machinery Co., Inc OPERATIONAL & MAINTENANCE MANUAL SEM Model 0201 OMD REV: 1 Security Engineered Machinery

Security Engineered Machinery Co., Inc

OPERATIONAL & MAINTENANCE MANUAL

SEM Model 0201 OMD REV: 1

Security Engineered Machinery Co., Inc

NATIONWIDE SERVICE

Phone Toll Free 1(800)225-9293

Email: [email protected]

Fax: (508)366-6814

Website: WWW.SEMSHRED.com

***IMPORTANT SAFETY PROCEDURES*** Your new CD/DVD shredder incorporates powerful, heavy duty cutting mechanisms, serious and permanent injury may result if proper precautions are not followed.

1. This equipment should never be operated by children or individuals that are untrained or incapable of understanding these safety precautions!

2. Do not reach into the feed opening for any reason! Never insert fingers, hands, other extremities, or objects not meant to be shredded into the feed opening!

3. Do not operate or come in close proximity to this equipment wearing long hair, necktie, loose clothing, or jewelry which may activate a photoelectric on/off switch and/or be pulled into the shredder.

4. Maintenance or repair of this equipment should be performed only be trained, authorized service personnel.

5. Always disconnect electrical power (unplug) before removing or opening the cover or other panels providing access to internal mechanisms.

SPECIFICATIONS Shred Size 2.2 mm x 4 mm Dimensions 40.25”H x 21.5”W x 23.25”D Weight 260 lbs. Cutting Power up to 1600 pieces/hr. CD’s or DVDs * IMPORTANT see below *Important: This machine is to be used for CD’s or DVDs only, not paper. If used for paper warranty may be voided. Note: For 115V/1/60Hz units a 20 amp line is required. For best results this line should not be more than 50 feet from the circuit breaker panel.

For NATIONWIDE SERVICE Call 1(800)225-9293

2

Table of Contents READ CAREFULLY BEFORE USING Proper care of your new CD/DVD shredder will ensure many years of trouble free operation, with minimum of maintenance or repair. IMPORTANT: Please note that all packaging should be retained by the customer for (30) days from the time of receipt. In the event that this unit needs to be sent back for replacement or repair this packaging will be required to do so. Should the packaging have been discarded before the (30) day requested period, packaging costs will be incurred by the customer. Contents Page No. Safety Procedures…………………………………………………………………………………………..2 Table of Contents…………………………………………………………………………………………..3 Safety Precautions………………………………………………………………………………………..4-6 Installation and Set-up………….…………………………………………………………………..............7 Operation and Feeding …………………………………………………………………………….…....8-11 Troubleshooting.…………………………………..…………………………………………………...12-15 Accessories..............……………………………………………………………………………………….16 Technical Information……………………………………………………………………………………..17 Spare Parts List ………………………………………………………………………………………...18-23 Wiring Diagram………………………………………………………………………………………...24-26

Customer Service Security Engineered Machinery Co., Inc. PO Box 1045 5 Walkup Drive Westboro, MA 01581 Tel: 800-225-9293 Fax: 508-366-6814 Website: www.semshred.com E-mail: [email protected]

Order On-line: GSA Customers: www.fedshred.com Commercial Customers: www.semshred.com IMPORTANT Two to three preventive maintenance calls per year are recommended Only authorized SEM service personnel should be allowed to service the shredder.


3

SAFETY PRECAUTIONS The door must be closed when operating the shredder. Ensure free access to mains. Automatic standby that switches off after 1 hour; green LED control light is off.

For NATIONWIDE SERVICE Call 1(800)225-9293 4

SAFETY PRECATIONS Cont… Remove plug before cleaning the machine. Do not operate the machine without the safety flap (A). ON/OFF! Quick stop’! Open the door!


SAFETY PRECATIONS Cont…

Destroyed CD/DVD material must not be emptied onto the floor. Danger of slipping!


INSTALLATION Installing the oiler: • Take the oiler holder out of the cabinet and hook it into the side of the cabinet (A). • Remove the lid from the oil bottle (B) • Put the oil tube into the oil bottle and screw on (C) • Click the tube into the connection (D) Insert the plastic bag in the container. Note: Must use SEM proprietary Anti Static Bag #638ASB0201. If not used static will affect machines performance and may void warranty.

Close the door; Plug into wall socket.


OPERATION When Using for the first time the oil pump starts automatically:

•Press after approximately 30 seconds red blinking LED (A) disappears. When the oil bottle (B) is changed: •Press the rocker switch “R” until the red LED (A) no longer blinks red. Flashing LED (A): •Cutting shafts are automatically oiled. Warning: Materials other than CD’s or DVDs may jam and /or damage the cutting unit. Shredding Paper may void Warranty. NO PAPER!


8

OPERATION Cont…. •Press the rocker switch (1.): green light is on, The machine is now ready for operation. •Machine starts automatically when CD/DVD is inserted. (Note: The machine will automatically switch off after one hour and the green LED control light will turn off.) •When the machine is switched off continuous operation can be switched on. Press or hold until the machine starts. To switch off the continuous operation press or hold or “R” Note: Feed one CD or DVD at a time only, through small slot only as shown in (2.)

LED shows red (A). Stops automatically if too many CD/DVDs are inserted. LED shows yellow (B). Maximum CD/DVDs capacity during shredding process. LED Shows green (C). Normal CD/DVDs capacity during shredding process.

Important: Between CD/DVDs insertion allow the machine to return to the LED green light. (C) If you insert CD/DVDs while the LED yellow light (B) is lit you may cause a jam, (See page 11 for jams). Stops automatically when no further CD/DVDs are inserted. By continuous operation press or “R” switch off.


9

OPERATION Cont…. Stops automatically when door is opened symbols and flash alternatively. Stops automatically when plastic bag is full. Enough (half full, because of weight, otherwise it is too heavy to be transported) The “bag full” indicator lights.

Stops automatically if too many CD/DVDs are inserted. Automatic reverse if CD/DVDs jam.

(Symbol “ON/OFF” flashes).

For NATIONWIDE SERVICE Call 1 (800)225-9293 10

OPERATION Cont….

If required: (Jam)

Open the safety flap (1.) Remove CD/DVD (2.) Reset by pressing the rocker switch . Re-feed the CD/DVD.


11

TROUBLESHOOTING Machine will not start. Is the machine plugged in? Is the rocker switch pressed?

Is the green light rocker switch ON? (1) Feed only one CD/DVD at a time into the opening (2).


12

TROUBLESHOOTING Cont…. Feed the CD/DVD into the center of the feed opening. (photo cell) (A) Is the door open? Is the container half full? Note: Container will not fill all the way this is a factory setting. If filled completely then container would be to heavy.


13

TROUBLESHOOTING Cont…. Machine will not stop.

Unplug from the main. Clean the photo cell (A) with a small brush or Q-tip with isopropyl (rubbing alcohol)

By continuous operation press or “R” switch off.

Machine stops. Symbols and “R” flash alternatively. • Overload protection. Cooling down period approximately 10-15 minutes. • Symbol lights green, machine is ready for operation. Container “indicator illuminates but bag is not half full. • Remove container (A) • Clean the level sensor with a brush (B) or Q-tip with isopropyl (rubbing alcohol)


14

TROUBLESHOOTING Cont…. None of the above mentioned methods helped To solve the problem: Contact our Customer Service at 1(800)225-9293


15

ACCESSSORIES Environmentally friendly oil (4 gallons) Part # 647OILHV Proprietary Anti-Static Plastic Bags (50 pieces) Part # 638ASB0201


16

TECHNICAL INFORMATION Do not shred paper clips. Do not destroy Paper.

This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 98/37/EG, 2006/95/EG and 2004/108/EG. Since 1/29/09 will be replaced by 2006/42/EG from12/29/2009 Sound Level Information: The sound level at the work place is less than the ISO 7779 standard’ maximum permissible level of<70 db (A). The exact technical specifications can be found on the technical specifications sticker on the machine. To claim under guarantee, the machine must still carry its original identification label. Subject to alterations without notice.


Parts List


18

Parts List Cont….


Parts List Cont….

Parts List Cont….


Parts List Cont….


Parts List Cont….


Parts List Cont….


23

Wiring Diagram


24

Wiring Diagram Cont…..


Wiring Diagram Cont…..


Documents

OPERATIONAL & MAINTENANCE MANUAL SEM Model · PDF fileSecurity Engineered Machinery Co., Inc OPERATIONAL & MAINTENANCE MANUAL SEM Model 0201 OMD REV: 1 Security Engineered Machinery